INTRODUCTION - House of Hifi
Contents
1. TEST Button Press to display the TEST PATTERN menu from which you can select the preferred test pattern ADJUST Button Press to display the ADJUST menu OPERATE Button Press to display the OPERATE menu Backlight Switch Turns the backlight on and off PIC FUNC Button Press to display the picture adjustment screen NOTE Some function items will not be used depending on the input video signal SOUND FUNC Button Press to display the VOLUME adjustment screen You can adjust the volume of the ISS 6010 ISS 6010G Switcher PICTURE PIC MUTE Button Press to mute the picture Press again to return the picture SOUND MUTE Button Press to mute the sound Press again to return the sound NOTE This works only with the ISS 6010 ISS 6010G DISPLAY Button Press to turn on or off the ON SCREEN display 11 12 13 14 15 16 17 18 19 20 FOCUS Button Press to enter the FOCUS mode STATIC Button Press to enter the STATIC mode You can adjust the static convergence POINT Button when the point convergence board installed Press to enter the POINT mode You can adjust the point convergence TILT SKEW ALIGN Button Press to enter the TILTSKEW ALIGNMENT mode You can adjust the tilt and the skew of the projected image TILT SKEW CONV Button Press to enter the TILTSKEW CONVERGENCE mode You can adjust the tilt and the skew convergence for the red or blue CRT B2. Remote control functions External control PC control Supplied accessories Environment Sound emission 610 W x 754 D x 309 H mm 24 1 8 W x 29 S B D x 12 1 8 H inch 56 kg 123 4lbs Wired application Wireless operating distance 7m 23ft User remote RC 6010 Power ON OFF Input signal select Picture mute Bright Contrast Color I Sharpness 1 Tint 2 Volume 3 Sound mute 3 Source information Static convergence Normalize Enter End Full function remote RC 6011 Test Display Help Information Input list Static focus Edge focus H V position White balance select Static convergence Wave convergence Point convergence H V amplitude HIV linearity H V key stone H V pin cushion H V blanking Tilt Skew H V bow Store Normalize Enter End Power ON OFF Input signal select Picture mute Bright Contrast Color 1 Sharpness 1 Tint 2 Volume 3 Sound mute 3 Source information Static convergence Normalize Enter End Power ON OFF Input signal select Picture mute Remote control data input Acceptable Full function remote control unit RC 601 I User remote control unit RC 6010 Remote cable 4m 13ft Remote cable 16m 52ft AC line cable Ceiling mounting kit User s manual Installation manual not included with PG 6000G PG 9000G Picture size spacers PC control software one manual and one floppy disk Temperature 0 to 40 degrees C Humidity 0 to 90 non c
3. INPUT 1 through 10 Changed to the corresponding number slot of the ISS 6010 ISS 6010G When using the projector with two ISS 6010 ISS 6010G or more To switch to another input signal enter the master slot number then the slave slot number by using INPUT but tons and press the ENTER button For example If you want to select a signal from the no 3 slot of the slave Switcher which is connected to the no 2 slot of the master Switcher first press the INPUT 2 button then the INPUT 3 button and finally press the ENTER button e When pressing any one of the INPUT buttons to directly access one signal among two or more of the same signals the projector will output the signal listed in the upper line automatically To select the one listed in the lower line use the CURSOR A or button and press the ENTER button INPUT SELECT List Format Page P01 to P10 Connection condition of the Switcher The Switcher connected NAME VTR 1 VTR 2 VIDEO 1 VTR 3 RGB 1 VIDEO 2 VIDEO 3 NTSC PAL SECAM Slot number of the master Switcher SW 2 LEVEL DATE 12 01 92 12 03 92 12 11 92 12 24 92 12 25 92 12 30 92 12 31 92 01 15 93 01 16 93 01 29 93 Date registered Source name of input signal Slot number of the sub Switcher BASIC OPERATION Source Information This is for viewing the signal information and the current status of various setting Proceed as follows 1 Press the OPERATE button e Th
4. be displayed 2 Use the CURSOR lt 4 or button to select YES XXXXXXXX 3 Press the ENTER button DATA NORMALIZE e The NORMAL function will be executed YES NO NOTE If you select NO you will exit this mode suspending current status XXXXXXXX Adjustment item to be normalized To return to the last stored level LOAD 1 Press the NORMAL button while holding down the CTL but ton e A confirmation message will be displayed 2 Use the CURSOR lt lt or P button to select YES XXXXXXXX DATA LOAD 3 Press the ENTER button e The LOAD function will be executed NOTE If you select NO you will exit this mode suspending current status YES XXXXXXXX Adjustment item to be loaded AN SPECIFICATIONS Projection type Projection system Scanning frequency Retrace time Video bandwidth CRT Lens Picture size Resolution Pixel resolution Light output Contrast ratio High voltage Input Convergence Convergence limits Warm up time Setup signal Power supply Power consumption Input current Safety and regulation Refraction type Projector and screen are separated 3 lens and 3 CRT s in line H 15 to 61 1kHz V 38 to 150Hz PG 6000 PG 6000G H 15 to 90kHz V 38 to 150Hz PG 9000 PG 9000G H 4 0 uS fH 15 to 30kH2 H 2 5 uS fH 30 to 9OkHz v 350 uS 7OMHz 3dB 7 inch liquid cooling Deflection angle 90 degrees Hybrid lenses multilayer co
5. signal from the INPUT SELECT list e See page 20 INPUT SELECTION for more details 5 Adjust the picture and sound e See pages 14 through 18 for more details NOTE The volume function works only with the ISS 6010 ISS 6010G 6 To turn off the power press the POWER OFF button on the remote control or the POWER button on the rear panel 7 Press the POWER switch on the front terminal to turn off the main power of the projector 8 Last turn off the connected equipment power BASIC OPERATION Displaying the Menu and Adjustment Screen You can easily access your desired screen by selecting menus Depending upon button selection your desired screen will be displayed as shown below a OPERATE menu NOTE Examples of the screen display are only when used with the ISS 6010 M 6010G PIC FUNC PICTURE menu PICTURE 1 BRIGHT 2 CONTRAST Adjustment screen 3 COLOR 4 SHARPNESS 5 TINT POSITION OPERATE menu POSITION menu POSITION 1 SHIFT Adjustment screen 2 BLANKING SOUND FUNC OPERATE 1 PICTURE SEERE 2 POSITION 3 SOUND Adjustment screen 4 INPUT SELECT INPUT LIST 5 SOURCE INFO INPUT SELECT screen 6 STATIC SOURCE INFO e The SOUND item is INFORMATION not included in the screen OPERATE menu on the stand alone TATI mode STATIG Adjustment screen e The PIC FUNC POSITION SOUND FUNC INPUT LIST INFO and STATIC buttons are on the full fu
6. terminal on the back of the Switcher NOTE Only the ISS 6010 ISS 6010G is compatible with this projector OPTION 1 Input Terminal For future system expansion S VIDEO Input Terminal Connect to the S video output of the external equipment such as VCR with an S video output VIDEO Input Terminal Connect to the video output of the external equipment such as video equipment S VIDEO VIDEO Select Switch Selects either the S VIDEO input or the VIDEO input terminal PART NAMES AND FUNCTIONS Control panel on the rear 11 12 13 mitnuiuo o POWER CONTRO OPLAATE ENTER ENO DOWN ue 11 POWER Button 17 UP Button Turns the projector on or off when the projector is Used to increase the selected adjustment level or in the standby condition Main Power switch on move the cursor upward When used with the and Standby indicator lit CONTROL button the UP button works as the CURSOR gt button on the remote control unit 12 CONTROL Button Used with other buttons similar to a shift key ona 18 NORMAL LOAD Button typewriter or computer This is the same with the Returns the adjustment data to the standard level CTL button on the remote control NORMAL function Pressing this button with holding down the 13 OPERATE Button CONTROL button returns the adjustment data to Press to display the OPERATE menu You can the last stored level LOAD function select the following adjustment functions from this menu 19 Select Counter 1 PICT
7. using the CURSOR buttons BLANKING e Top U and Right R Pressing Aor P increases Pressing Wor 4 decreases e Bottom D and Left L Pressing W or lt 4 increases Pressing A or P decreases To end this adjustment press the END button to display the STORE menu e Whenever the END button is pressed the screen will be changed in this order POSITION menu P OPERATE menu STORE menu Use the CURSOR lt 4 or P to select either YES or NO and press ENTER STORE e If the position adjustments have not been changed the STORE menu will not be displayed YES NO e Will be returned to the source screen Items to select The data will be stored The data will not be stored e To exit this mode without storing the current status select NO If the current status is not stored due to other button operation the STORE menu will be displayed BASIC OPERATION Sound Adjustment only when used with the ISS 6010 ISS 6010G Adjust the volume to your preference Proceed as follows 1 Press the OPERATE button e The OPERATE menu will be displayed 2 Use the CURSOR A or F button to highlight the 3 OPERATE SOUND line and press the ENTER button to display the 1 PICTURE c 2 POSITION VOLUME screen You can also select the VOLUME 5 SOUND screen directly by pressing the INPUT 3 button 4 INPUT SELECT 5 SOURCE INFO NOTE You c
8. FUNCTIONS Terminal panel on the front 1 POWER Switch Main power 6 Press to turn the main power on The STANDBY indicator is lit In this condition you can start up the projector by pressing the POWER ON button on the remote control or the POWER button on the rear panel Press again to turn the main power off NOTE When turning off the main power first return the projector to the standby condition by pressing the POWER OFF button on the remote 7 control or the POWER button on the rear panel and then turn off the main POWER switch These procedures are to protect your projector and the 8 connected equipment 2 AC INPUT Connect the supplied power cord here 9 3 REMOTE 2 Jack When the supplied full function remote control is used in the wired condition connect the supplied 10 remote cable here The wireless control does not work when the plug of the remote cable is inserted here 4 RGB H V and V Input Terminals Connect R G B H Horizontal sync and V Vertical sync outputs of the external equipment such as the Switcher If using a component with a combined sync SYNC output connect it to the H V terminal 5 Remote Sensor Receives the signal from the supplied remote control when used in the wireless condition REMOTE 1 Terminal This terminal allows external control of the projector from either the Switcher or from an external control When the Switcher is used connect to the REMOTE 1
9. INTRODUCTION Before operating this projector please read this manual carefully and completely This manual will provide you with the basic instructions for operation of the projector Installation preliminary adjustments and procedures which require the opening of the projector and contact with electrical components should be performed by service personnel For continued safe and reliable operation use only cables supplied by the manufacturer for power Adhere to all notes and warnings Features Multi scan circuit automatically locks on video superdata from 15kHz to 61 1kHz MultiSync 6PG and graphics signals from 15kHz to 90kHz MultiSync 9PG You can interface video and high resolution RGB signals from various computers workstations and graphics boards 7 CRTs with deflection angle 90 degrees produce a detailed picture with a resolution of 1280 x 1024 pixels Impregnated cathode used in the CRTs makes possible 800 lumens of light output ECP lens produces an image with true color reproduction e AKB circuit provides a stable white balance The wide band video circuit provides of 7OMHz of Video Bandwidth Display size can be altered to accommodate any picture size from 60 to 300 diagonal In addition to ceiling mounting floor desk top and rear installations are possible Digital point convergence provides high accuracy for a projecting fine graphic displays This can be purchased as an optional item for the M
10. OW ALIGN Button Press to enter the BOW ALIGNMENT mode You can adjust the horizontal and the vertical bow of the projected image BOW CONV Button Press to enter the BOW CONVERGENCE mode You can adjust the horizontal and the vertical bow convergence for the red or blue CRT AMPLITUDE ALIGN Button Press to enter the AMPLITUDE ALIGNMENT mode You can adjust the horizontal width and the vertical height of the projected image AMPLITUDE CONV Button Press to enter the AMPLITUDE CONVERGENCE mode You can adjust the horizontal and the vertical convergence amplitude for the red or blue CRT LINEARITY ALIGN Button Press to enter the LINEARITY ALIGNMENT mode You can adjust the horizontal and the vertical linearity of the projected image PART NAMES AND FUNCTIONS 21 22 23 24 25 26 27 28 29 LINEARITY CONV Button Press to enter the LINEARITY CONVERGENCE mode You can adjust the horizontal and the vertical linearity convergence for the red or blue CRT Pressing with CTL button controls the LINEAR BALANCE convergence KEY STONE ALIGN Button Press to enter the KEY STONE ALIGNMENT mode You can adjust the horizontal and the vertical key stone of the projected image Pressing with CTL button controls the KEY BALANCE alignment KEY STONE CONV Button Press to enter the KEY STONE CONVERGENCE mode You can adjust the horizontal and the vertical key stone convergence for the red or blue CRT Pressing
11. R button to display the POSI TION menu You can also select the 2 POSITION menu directly by pressing the INPUT 2 button 3 Use the CURSOR A or F button to select either or BLANKING and press the ENTER button You can also select the item directly by pressing the INPUT 1 or 2 button e The selected adjustment screen will be displayed Items to select SHIFT Position of the picture e BLANKING Screen area NOTE You can enter the position adjustment screen di rectly using the POSITION button on the full function re mote control The POSITION button will toggle between the SHIFT and BLANKING 4 Adjust the position or screen area When selecting SHIFT Use the CURSOR buttons to move the position of the picture e Pressing lt or P moves the picture left or right e Pressing A or V moves the picture up or down NOTE Adjust to position the picture in the center of the raster Over shift adjusting to the top of the raster may cause the top of the picture to curve OPERATE 1 PICTURE 2 POSITION 3 SOUND 4 INPUT SELECT 5 SOURCE INFO 6 STATIC POSITION 1 SHIFT 2 BLANKING POSITION SHIFT BASIC OPERATION When selecting BLANKING 1 2 Hold down the CTL button and press CURSOR buttons to choose the right left top or bottom edge The marker on the selected side will turn to a solid color A v POSITION Adjust the blanking
12. T SELECT list directly 6 STATIC using the INPUT LIST button on the full function remote control P01 INPUT SELECT 3 Use the CURSOR Aor F button to highlight the signal to be ISS 6010 SW 2 LEVEL switched to and press ENTER to change to the selected input signal NO INPUT NAME DATE 01 M 01 S 01 VTR 1 12 01 92 02 M 01 S 02 VTR 2 12 03 92 03 M 01 S 03 VIDEO 1 12 11 92 04 M 01 S 04 VTR 3 12 24 92 05 M 01 S 05 RGB 1 12 25 92 06 M 01 S 06 VIDEO 2 12 30 92 07 M 01 S 07 VIDEO 3 12 31 92 08 M 01 S 08 NTSC 01 15 93 09 M 01 S 09 PAL 01 16 93 10 M 01 S 10 SECAM 01 29 93 NOTE To advance to the next page or to the previous page hold down the CTL button then press the CURSOR A or V button To directly access a page hold down the CTL button then any one of the INPUT buttons 4 Toend the INPUT SELECT list press the END button e Whenever the END button is pressed the screen will be changed in this order OPERATE men Source screen Continued on the next page BASIC OPERATION NOTE e While you are viewing a source screen you can also select the input signal directly by pressing the INPUT 1 through 10 button In this case INPUT buttons function as follows When using the projector in stand atone operation INPUT 1 Changed to the VIDEO input or S VIDEO input on the projector INPUT 2 Changed to the RGB input on the projector When using the projector with the ISS_6010 ISS 6010G
13. URE A INPUT SELECT Displays 00 in normal operation 2 POSITION 5 SOURCE INFO 3 SOUND 6 STATIC 20 REMOTE Indicator Flashes when the projector receives a signal from NOTE The SOUND item is not included in the the remote control OPERATE menu on the stand alone mode 21 STANDBY Indicator 14 ENTER Button Lights up when the projector s main POWER Executes menu selection and switches to selected switch is on Flashes when the projector might not input be connected with the Switcher correctly or when the Switcher might be turned off 15 END Button Exits t adjustment mode 22 POWER Indicator Lights up when the projector is turned on 16 DOWN Button Used to decrease the selected adjustment level or 23 Remote Sensor move the cursor downward When used with the Receives the signal from the supplied remote CONTROL button the DOWN button works as control when used in the wireless condition the CURSOR lt button on the remote control unit PART NAMES AND FUNCTIONS Remote control unit User Remote Control RC 6010 Full Function Remote Control RC 6011 NOTE The full function remote control is designed for setup adjustment Use the user remote control for normal operation PART NAMES AND FUNCTIONS 1 10 POWER Buttons ON OFF Press the ON button to turn the projector on when the projector is in the standby condition STANDBY indicator lit Press the OFF button to return the projector to the standby condition
14. an enter the VOLUME adjustment screen di 6 STATIC rectly using the SOUND FUNC button on the full function remote control SOUND 3 Use the CURSOR buttons to adjust the volume e The CURSOR P or A button increases the volume VOLUME The CURSOR lt lt or V button decreases the volume 4 Toend this adjustments press the END button to display the STORE menu e Whenever the END button is pressed the screen will be changed in this order OPERATE menu STORE menu STORE 5 Use the CURSOR lt or P button to select either YES YES NO or NO and press the ENTER button e If the VOLUME data has not been changed the STORE menu will not be displayed Items to select The data will be stored The data will not be stored e To exit this mode without storing the current status select No If the current status is not stored due to other button operation the STORE menu will be displayed BASIC OPERATION Input Selection You can switch from one input to any other input signal Proceed as follows 1 Press the OPERATE button e The OPERATE menu will be displayed 2 Use the CURSOR A or F button to highlight the 4 INPUT OPERATE SELECT and press ENTER to display the INPUT SE 1 PICTURE LECT list You can also select the INPUT SELECT list a o directly by pressing the INPUT 4 button 5 SOURCE INFO NOTE You can display the INPU
15. ating F1 0 60 to 300 inches diagonal LOOOTV lines 1280 x 1024 dots 800 lumens Small area peak high light brightness 1 200HDTV method 32kV RGB signal 0 7Vp p 75ohm positive BNC H V sync 0 7 to 4 0Vp p 75ohm negative or positive BNC COMP sync 0 7 to 4 0Vp p 75ohm negative o r positive BNC Sync on G 0 3 to 0 6Vp p 75ohm negative BNC Video 1 0Vp p 75ohm positive BNC or switchable S video Y I OVp p 7S5ohm positive C 0 28Vp p 75ohm burst level Video system NTSC PAL SECAM and NTSC4 43 Digital convergence Pre set 100 positions Quick copy convergence Static and wave convergence Point convergence PG6000 PG 6000G Optional PG 9000 PG 9000G Standard Less than 0 2 of V height 20 minutes Cross hairs Cross hatch Dot Window pattern H test pattern AC 120V 60Hz PG6000 PG 9000 AC 220 240V 50Hz PG6000G PG 9000G PG 6000 PG 6000G 430W PG 9000 PG 9000G 500W 5 8A AC 120V PG 6000 6 7A AC 120V PG 9000 3 8A AC 220 240V PG 6000G 4 4A AC 220 240V PG 9000G PG 6000 PG 9000 Meets FCC class A requirements UL Approved UL 1950 Governed by IEC 950 CSA certified Meets DHHS requirements PG 6000G PG 9000G Meets TUV GS requirements Governed by EN 60950 and IEC 950 Meets FTZ class B requirements Governed by DBP Vfg 243 Meets x ray requirements Governed by R ntgenverordnung R6V lava SPECIFICATIONS Cabinet dimensions Weight Remote control
16. e OPERATE menu will be displayed 2 Use the CURSOR Aor V button to highlight the 5 SOURCE INFO line and press the ENTER button to display the SOURCE INFORMATION screen You can also select the SOURCE INFORMATION screen directly by pressing the INPUT 5 button NOTE You can enter the SOURCE INFORMATION screen directly using the INFO button on the full function remote control 3 To end the SOURCE INFORMATION screen press the END button e Whenever the END button is pressed the screen will be changed in this order OPERATE menu P Source screen NOTE You can not change NAME LOCK SYNC DETECT COLOR TEMP AKB COUNTER and TIMER in this screen SOURCE INFORMATION Screen Format OPERATE 1 PICTURE 2 POSITION 3 SOUND 4 INPUT SELECT 5 SOURCE INFO 6 STATIC SOURCE INFORMATION M 01 S 01 A LOCK se ON FREQUENCY F SYNC DETECT fh 3k KHz AUTO Fv 2 Hz MANUAL SEPA G SYNC SYNC COLOR TEMP AKB HD VD 6500 K VIDEO MODE 9300 K OFF COUNTER TIMER NTSC 3 58 FEAR RRA KKK SEK Slot number of the master switcher Slot number of the sub switcher Slot number of the master switcher DURCE INFORMATIO 3K KKK KAKA ON Scanning frequency OFF SYNC DETECT fh 2 KHz AUTO COMP Fv Hz MANUAL SEPA G SYNC SYNC input polarity YNC Source lock for RGB signal Sync signal Color temperature COLOR TEMP AKB Auto wh
17. enter the picture adjustment screen directly using the PIC FUNC button on the full function remote control Each time you press the PIC FUNC button the picture functions will rotate as follows CONTRAST gt COLOR gt SHARPNESS gt TINT BRIGHT 4 Use the CURSOR buttons to adjust a picture to your preference e The CURSOR P or Abutton increases the level BCTORE e The CURSOR lt or V button decreases the level BRIGHT 5 To end this adjustment press the END button to display the STORE screen e Whenever the END button is pressed the screen will be changed in this order PICTURE menu gt OPERATE menu gt STORE menu e If the picture adjustments have not been changed the STORE menu will not be displayed BASIC OPERATION 6 Use the CURSOR lt or P button to select either YES or NO and press the ENTER button e Will be returned to the source screen STORE YES NO Items to select The data will be stored The data will not be stored e To exit this mode without storing the current status select NO If the current status is not stored due to other button operation the STORE menu will be displayed BASIC OPERATION Position Adjustment Adjust the position and screen area Proceed as follows 1 Press the OPERATE button e The operate menu will be displayed 2 Use the CURSOR Aor button to highlight the 2 POSI TION line Press the ENTE
18. ing control levels cursor movement and convergence adjustments NORMAL Button Returns the adjustments level for each VIDEO or RGB input signal to the standard level When pressed once the confirmation message will be displayed When YES is selected and ENTER is pressed the data will be returned to the standard level Pressing with CTL returns the adjustment data to the last stored level LOAD function STORE Button Memorizes the adjustments setting of each VIDEO or RGB input signal separately When pressed once the confirmation message STORE will be displayed When selecting YES and ENTER is pressed the data will be stored in memory END Button Ends the adjustment mode ENTER Button Executes menu selection and switches to selected input CTL Button Used with other buttons similar to a shift key on a typewriter or computer Remote Control Jack Insert the plug of the supplied remote cable here when the full function remote control is used in the wired condition PART NAMES AND FUNCTIONS Battery installation and replacement User remote control Full function remote control 1 Press down on the battery compartment cover 1 Press down on the battery compartment cover and slide the cover in the direction of the arrow and slide the cover in the direction of the arrow 2 Install the two new batteries making sure that their 2 Install the two new batteries making sure that their polari
19. ings Power supply The PG 6000 and PG 9000 projector are designed to operate on 120V 60H2 and the PG 6000G and PG 9000G are designed to operate on 220 240V 50Hz AC power supply Make sure your local power supply matches these requirements before operation Handle the power cord carefully and avoid excessive bending A damaged cord may cause electric shock or fire If the projector is not to be used for an extended period remove the plug from the power outlet Cleaning Unplug the projector from the power outlet before cleaning Clean the cabinet and front panel periodically with a soft cloth If heavily stained use a mild detergent solution Never use strong detergents or solvents such as alcohol or thinner to clean your projector Lens cleaning Avoid touching the lens surfaces Special coating is applied to the lens surfaces Consult your dealer for lens cleaning Fire and Shock Precautions Adequate ventilation must be provided to prevent heat build up inside the projector Make sure the ventilation holes are unobstructed Keep the inside of the projector free from foreign objects such as paper clips nails paper etc Do not attempt to retrieve such objects yourself or insert metal objects such as wire and screw drivers inside the projector If a hazardous object falls inside the projector unplug it immediately and call a qualified electrical repairman for removal Do not set liquids on top of the projector PART NAMES AND
20. ite balance HD VD 3200 K a 6500 K ON ideo color system VIDEO MODE 9300 K OFF COUNTER TIMER NTSC 3 58 FE AK OK KK FE AK IK 3K NOTE The example of the screen display is only when Counter Timer BASIC OPERATION Static Convergence Adjustment Adjust for the red and blue CRTs to place their pattern on top of the green test pattern center only NOTE The static convergence adjustment should be per formed for R and B CRT Carry out the adjustment after dis playing a motion picture for 20 minutes or more Proceed as follows 1 Press the OPERATE button e The OPERATE menu will be displayed OPERATE 2 Use the CURSOR A or button to highlight the 6 1 PICTURE STATIC line and then press the ENTER button to display 2 POSITION 3 SOUND 4 INPUT SELECT 5 SOURCE INFO ANG the STATIC adjustment screen You can also select the STATIC adjustment screen directly by pressing the INPUT 6 button NOTE The STATIC adjustment can also be displayed by pressing the STATIC button on the full function remote con trol CONVERGENCE 3 Press the R or B button to display the pattern to be aligned 2 RAG with the Green pattern as used a reference color CRT R e You can turn on or off each CRT beam R and B separately 4 Hold down the CTL button then select the CRT you wish to adjust with the R and B buttons 5 Align the center of the Red or the Blue pattern with the ce
21. nction remote control only CAUTION Do not display a bright and still picture for longer than 20 minutes This could damage the CRTs NOTE The explanation of the operation on the following pages is for use with the remote control You can also operate the projector using the buttons on the control panel of the projector BASIC OPERATION Picture Adjustment To adjust the picture for each input proceed as follows NOTE The Color Sharpness and Tint controls are not included in the PICTURE menu for RGB signal The Tint control is not included in the PICTURE menu for SECAM PAL signal 1 Press the OPERATE button e The OPERATE menu will be displayed OPERATE 2 Use the CURSOR Aor button to highlight the IPICTURE and press the ENTER button to display the PICTURE 2 POSITION 3 SOUND menu You can also select the PICTURE menu directly by pressing the INPUT 1 button eae 5 SOURCE INFO 6 STATIC PICTURE 3 Use the CURSOR A or Wbutton to select a picture function 1 BRIGHT and then press the ENTER button You can also select an 3 f sA item directly by pressing an Input button 4 SHARPNESS e The picture adjustment screen will be displayed 5 TINT Items to select e BRIGHT Bright control CONTRAST Contrast control e COLOR Color intensity control SHARPNESS Picture detail control TINT Red and green values control NOTE You can
22. nter of the Green pattern using the CURSOR buttons e The CURSOR lt aP button moves the pattern right or left The CURSOR A or V button moves the pattern up or down 6 Repeat steps 3 to 5 for the other CRTs if necessary 7 To end this adjustment press the END button to display the STORE menu e Whenever the END button is pressed the screen will be changed in this order OPERATE menu STORE menu An BASIC OPERATION 8 Use the CURSOR lt aP button to select either YES or NO and press the ENTER button e If the STATIC convergence data has not been changed the STORE menu will not be displayed Items to select The data will be stored The data will not be stored e To exit this mode without storing the current status select NO If the current status is not stored due to other button operation the STORE menu will be displayed BASIC OPERATION Picture and Sound Mute This function mutes a picture or sound To mute a picture or sound e Pressing PICTURE PIC MUTE mutes a picture Pressing SOUND MUTE motes sound Pressing again restores the picture or sound NOTE When picture is muted no OPERATE menu or ADJUST menu can be accessed Normal and Load Function Adjustment settings can be returned to the standard level or the previously stored set level To return to the standard level NORMAL 1 Press the NORMAL button e A confirmation message will
23. ondensing Storage 10 to 50 degrees c PG 6000 PG 9000 45dB PG 6000G PG 9000G 70dB A Complies with DIN 45635 or ISO 7779 1 This works only for VIDEO signals 2 This works only for NTSC video signals 3 This works only with the Switcher operation Specifications are subject to change without notice The dimensions given for the projector do not include protruding parts AA APPENDIX Screen Format in Projecting a Picture NOTE The example of the screen display is only when used with the ISS 6010 ISS 6010G Date Current time Input Source name NOTE e Consult your dealer for changing the on screen display mode e Ifthe main power is not supplied to the projector for three days or more the built in clock may have to be reset If this happens consult your dealer for setting date and time ne
24. ty matches the diagrams inside the polarity matches the diagrams inside the battery compartment battery compartment NOTE The remote control is powered by two 1 5V AA batteries Remote control cautions Use the remote control within the valid operating range within a distance of about 7m 23 ft and at 30 degrees angle left and right Handling remote control and batteries Do not drop or mishandle the remote Do not get the remote wet If the remote gets wet wipe it dry immediately Avoid heat and humidity e When not using the remote for a long period remove the batteries e Do not use new and old batteries together or use different types together e Do not take apart the batteries heat them or throw them into a fire e Avoid using the full function remote control as wireless with the backlight switch ON for an extended period of time This can cause short battery life BASIC OPERATION Projecting the Picture aeesoeoanvee User remote control To project the picture source proceed as follows 1 Turn on the main power of the projector e Press the POWER switch on the front terminal 2 Turn on the connected equipment s power 3 Turn on the power e Press the POWER ON button on the remote control or the POWER button on the rear panel 4 Select an input signal source by pressing one of the ten INPUT buttons on the remote control You can also select a
25. ultiSync 6PG Easy accessing of adjustment item with on screen menus e Accepts up to 100 inputs with the ISS 6O10 ISS 6010G Video system compatible with NTSC PAL SECAM and NTSC 4 43 Up to 100 convergence patterns can be stored in the stand alone mode in digital memory Quick copy convergence for fast easy set up from one preset signal Built in self diagnostics for on sight troubleshooting Built in CROSS HAIR CROSS HATCH DOT WINDOW and H FOCUS test patterns for accurate setup Source information status display The SEQUENCER function allows the projector to automatically select input signals one after another INTRODUCTION Important Safeguards The following are important safety instructions designed to ensure the long life of your projector and to prevent fire and shock hazards Be sure to read these safety instructions carefully and follow all warnings given below Installation Place the projector on a flat level surface and in a dry area free from dust and moisture Do not place the projector in direct sunlight near stoves or other heat radiating appliances Smoke steam and exposure to direct sunlight could adversely affect the internal components Avoid rough handling when moving your equipment as a strong shock could damage its internal components If installing the projector on the ceiling use only parts supplied by the manufacturer Observe all instructions and warn
26. with CTL button controls the KEY BALANCE convergence PIN CUSHION ALIGN Button Press to enter the PIN CUSHION ALIGNMENT mode You can adjust the horizontal and the vertical pin cushion of the projected image Pressing with CTL button controls the PIN BALANCE alignment PIN CUSHION CONV Button Press to enter the PIN CUSHION CONVERGENCE mode You can adjust the horizontal and the vertical pin cushion convergence for the red or blue CRT Pressing with CTL button controls the PIN BALANCE convergence INPUT Button Selects menus and switches input signals HELP Button Press to display the explanation of the current selected function and available functions INPUT LIST Button Press to display the list of the recorded input signals INFO Button Press to display the various parameters and settings of the currently displayed image 30 31 32 33 34 35 36 37 38 39 KELVIN Button Press to enter the WHITE BALANCE mode You can adjust the white and the black level POSITION Button Press to enter the position mode You can adjust the horizontal and vertical position and horizontal and vertical blanking R G and B Buttons Turn each CRT beam on and off separately When using with the CTL button you can select the CRT to be adjusted during convergence and center focus adjustments Note that the G button is only on the full function remote control CURSOR Buttons Used for increasing and decreas
Download Pdf Manuals
Related Search