User Manual
Contents
1. a safety cable that can hold 12 times of the Hook optional Safety cable optional weight of the unit when installing the fixture The equipment must be fixed by professionals And it must be fixed at a place where is out of the touch of people and has no one pass by or under it 3 8 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The fixture does not work no light Check the connection of power and main fuse 2 Measure the mains voltage on the main connector Not responding to DMX controller DMX LED should be on If not check DMX connectors cables to see if link properly If the DMX LED is on and no response to the channel check the address settings and DMX polarity If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may MN cause damage or interference to DMX interface circuit Some fixtures don t respond to the easy controller You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal No response to the sound Make sure the fixture does not receive DMX signal Check microphone to see if it is good by tapping the microphone O2. the MENU button up to when the rhe is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button eT Software version Press the MENU button up to when the Lee is blinking on the display Pressing ENTER button and the display will show the version of software of the unit To go back to the functions press the MENU buiton Reset Press the MENU button up to when the is blinking on the display Pressing ENTER button and all the motors will back to their home position 4 3 Home Position Adjust Press Enter button for about 5 seconds OPAN will shown on the display press ENTER button to confirm then use DOWN and UP button to adjust the home position 127 127 of the motor Once the position has been selected press the ENTER button to setup or exit the offset mode without any change press the MENU button 5 How To Control The Fixture You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller 3 By DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show 340b on the display After that the unit will be ready to receive DMX signal or run the built in programs 5 1 Master Slave Built In Preprogrammed Function By linking the units in mas
3. to 1 5 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin4 5 not used 4 How to set the fixture OS m i g 10 ee i ai 48 E 1 Display To show the various menus and the selected functions LED 3 MASTER On Master Mode 4 SLAVE On Slave Mode Button To select the programming functions To go backward in the selected functions To go forward in the selected functions To confirm the selected functions 0 DMX output For DMX512 link use 3 5 pin XLR plug cable to input DMX signal A DMX input For DMX512 link use 3 5 pin XLR plug cable to link the next unit 2 Only for remote control By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode function 3 Microphone Receive music for the sound active 4 Safety Ring For attached the safety cable 5 Mains output Connect to supply mains power for the next unit 6 Mains input Connect to supply mains power 4 4 2 Main Function To select any functions press MENU button until the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press ENTER button to 6 DMX512 Configuration 1 amp 3
4. CH modes setup or it will automatically return to the main functions without any change after idling 10 DMX512 Configuration seconds Back to the functions without any change press MENU button The main functions are shown below Chi Ch2 Sng Dimmer Strobe Color Rotation 4 DMX512 Address Setting ao Ron ge TER Rand eas Cor i 4 olor H ra el 250 255 Chase TE xe nie ii Chase jI 248 255 208 218 Colorz 246 255 T am Mast Mode 230 249 Chase 11 200 207 Color 26 TT olor Gi Slave Mode Normal 210 229 Chase 10 184 191 Color 24 GL o Slave mode 2 Light Show 190 209 Chaseg 200 247 aera Elles 135 045 te 160 167 Color 21 sai ama Show 170 189 Chase 8 182 189 Color 20 i WI iE HH 2 150 169 Chase 7 136 143 Color 18 OOF Ty on a 130 149 Chase6 120 127 Color 16 a 110 129 Chase 5 104 111 Color 14 we J4 olor MENUH eT o Sound Mode on 096 103 Color 13 oF F Sound Mode off 90 109 Chase 4 o56 085 Cobra orig EES Blackout Mode Yes Blackout 70 89 Chase 3 072 079 Color 10 Blackout Mode No Blackout 064 071 Color 9 ToT LED 90 69 Chase 2 056 063 Color 8 Pa on on 048 055 Color7 off LED off 30 49 Chase 1 040 047 Color6 032 039 Color 5 IEP di SP Normal 0 29 OFF 024 031 Color 4 2s j olor 45 19 Inversion 008 015 Color 2 te St Self Test 000 007 Color 1 Fixture Hours uf Software Version SPH Reset DMX 512 Address Setting Press the MENU button up to when the is shown on the displ
5. Versia LINKABLE T i k SSS E e LED 340B User Manual Please read the instructions carefully before use Innovation Quality Performance 15 TABLE OF CONTENTS 1 Safety Instructions 2 Technical Specifications 3 Installation 4 How to set the fixture 5 How to control the fixture 6 DMX 512 Configuration 7 DMX 512 Connections 8 Troubleshooting 9 Fixture Cleaning EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements 14 9 Fixture Cleaninc The cleaning of internal must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60
6. ay Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX 512 address Once the address has been selected press ENTER button to setup or automatically exit menu mode without any change after 10 seconds Back to the previous functions without any change press MENU button Channel Mode 5 2 Easy Controller by CA 8 it The easy remote control is used only in master slave mode By connecting 2 O to the 1 4 microphone jack of the first unit you will find that the remote j controller on the first unit will control all the other units for Stand by Function and Mode selection Mira hs Blackout Blackout the unit Select Speed Select Show 1 Slow Show 1 8 2 Middle 3 Fast Ay col ify n ii l 7 ji a i rii ae 1 44 1 SynchroStrobe Function 2 Asynchro Strobe 3 Sound Strobe Sound Strobe Show ae LED OFF LED ON LED blinking 5 3 DMX Controller Using universal DMX controller to control the units you have to set DMX address from 1 to 512 channels so that the units can receive DMX signal Press the MENU button up to when the Modder js showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to t
7. d on or sound off Once select press ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button ur Ng _ O Blackout mode Press the MENU button up to when the bind is shown on the display Pressing ENTER button Use DOWN and UP button to select the blackout or normal Once select press ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button LED display Press the MENU button up to when the Led is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP buiton to select display on or L oF Fldisplay off mode Once select press ENTER button to setup or exit menu mode without any change after 10 seconds Back to the functions without any change press MENU button again AJI CO Li I Display Inverse _ it Press MENU button until is blinking on the display Use DOWN and UP button to select normal or ds iP inverse press ENTER button to setup Back to the functions without any change press MENU button OC iL ct Self Test Press the MENU button up to when the best is blinking on the display Pressing ENTER button and the unit will run the built in programmer for self test To go back to the functions press the MENU button cot rir 5 Fixture Hours Press
8. days 13 WARNING 1 Safety Introductions A N Please read the instructions carefully which includes important information about the installation operation and maintenance Please keep this User Manual for future consultation If you sell the fixture to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the fixture Its important to ground the yellow green conductor to earth in order to avoid electric shock Disconnect main power before servicing and maintenance Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this In the event of serious operating problem stop using the fixture immediately Never try to repair the fixture by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Do not connect the device to any dimmer pack Do not touch any wire during operation and there might be a hazard of electric shock To prevent or reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture The housing must be replaced if they are visibly damaged Do not look directly at the LED light beam while the fixture Is on There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs by yoursel
9. f In the unlikely event your fixture may require service please contact your nearest dealer Due to the magnifying type lens please keep the lens out of contact with direct sunlight Direct sunlight can cause heat to build up inside of the unit which will seriously damage unit For power supply do not connect in series much more than 31 units use another mains supply for next 31 units 2 technical Specifications Featuring 1 x 10W tri color high powered LED and specially designed mechanism the Radiant LED shoots tons of powerful and laser like muticolor beams covering the entire room with amazing effects Great built in lighting shows under Master Slave and Sound Active Full range dimmer and variable strobe effects Optional CA 8 easy controller for enjoying instant lighting shows at you fingertips LED display for easy navigation idear for discotheques clubs bars parties Mobile Dus ect Input Voltage 100V 240V 50 60Hz Power consumption 20W Fuse T 6 3A LED 1 x 10W Tri color LEDs 30000hrs rated Dimension 301 x 235 x 290mm J Weight 4 5kgs oo A 235 3 Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly A e fixed to avoid vibration and slipping while operating p Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the units weight Also always use
10. he functions without any change press the MENU button again If you use please refer to the following diagram to address your DMX512 channel for the first 4 units aa E E E 3 channels mode HEALT Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the 1 channel or 3 channels mode Once select press the ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button cin fits Slave Mode Press the MENU button up to when the Sind is shown on the display Pressing ENTER button Use DOWN and UP button to select the master or Si slave 1 or Gi ol Slave 2 mode Once select press the ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button 5 mn i d Show Mode Press the MENU button up to when the SAd is shown on the display Pressing ENTER button Use DOWN and UP button to select the Sh i Random show or Gh show 1 or Gh ol Show 2 or or show8 Once select press ENTER button to store or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the Soun
11. ne of the channels is not working well The stepper motor might be damaged or the cable connected to the PCB is broken The motor s drive IC on the PCB might be out of condition 7 DMX512 Connections The DMX8512 is widely used in intelligent lighting control with a maximum of 512 channels COMMON os ay fr DMXINPUT 3 2 2 DMX OUTPUT Na 5 DMX SY Termination reduces signal errors and to avoid signal DaN transmission problems and interterence Itis always se advisable to connect a DMX terminal ws Resistance 120 ohm 1 4W between pin2 DMX and rw pin3 DMX of the last fixture 1 Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 2 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 3 At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 Each lighting fixture needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually O amp 1 are equal
12. ter slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to set the first unit in master mode and select Sh Olrandom show ah li show 1 or or show 8 Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to select normal or 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave led lights will constantly on 2 light show In slave mode means the unit works as the master unit and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only
Download Pdf Manuals
Related Search