AEG F 65411 VI Dishwasher User Guide Manual Operating
Contents
1. 1 Open the appliance door The washing program stops 2 Close the appliance door The washing program continues from the point of interrup tion Cancelling a washing program 1 Press and hold function buttons B and C until all the program lights come on 2 Release function buttons B and C to cancel the washing program At this point you can follow these steps 1 Switch off the appin Downloaded from DishWasher Manual com Manuals Select and start a washing program 2 Seta new washing program Fill the detergent dispenser with detergent before you set a new washing program End of the washing program The washing program is complete when e The appliance stops automatically e The audible signal for the end of the program operates 1 Open the door The digital display shows 0 The indicator light for the completed program stays on 2 Switch off the appliance For better drying results keep the door ajar for some minutes before you remove the dishes Let the dishes cool down before you remove them from the appliance Hot dishes are easily damaged Removing the load e First remove items from the lower basket then from the upper basket e There can be water on the sides and door of the appliance Stainless steel becomes cool more quickly than the dishes Standby mode If you do not switch off the appliance at the end of the washing program the appliance automatically goes into standby mode The stand2. i If you connect the water drain hose to a trap spi got under the sink remove the plastic membrane If you do not remove the membrane remaining food can cause a blockage in the drain hose spigot The appliance has a security feature to prevent dirty water going back into the appliance If the spigot of the sink has a non return valve this valve can cause the appliance to drain incorrectly Remove the non return valve Remove entire internal membrane wy CAUTION Make sure that the water couplings are tight to prevent water leakage Ensure that hoses are not crushed or kinked under or behind the appliance Once connected the inlet hose to the water tap turn the tap on and check that there are no leaks D KUUE s D MAY N ELECTRICAL CONNECTION WARNING Safety standards require the appliance to be earthed Prior to using the appliance for the first time ens supply on the rating plate match that of the supp The fuse rating is also to be found on the rating p Always plug the mains plug onto a correctly insta ure that the rated voltage and type of ly where the appliance is to be installed ate led approved socket Do not use multi ways plugs connectors and extension cables This can constitute a fire hazard through overheating If necessary have the domestic wiring system soc replaced contact your local Customer Care centre et replace
3. 330 399 2310 SI 3339 2 5 260 329 260 329 2 6 3 2 1 4 190 259 190 259 1 9 2 5 1 3 70 189 70 189 0 7 1 8 1 2 lt 70 lt 70 lt 0 7 1 1 1 No use of salt required i You must set the water softener manually and electronically Manual adjustment i The appliance is set at the factory at position 2 1 Open the door 2 Remove the lower basket 3 Turn the water hardness dial to position 1 or 2 refer to the chart 4 Install the lower basket 5 Close the door Electronic adjustment i The dishwasher is factory set at level 5 1 Switch on the appliance 2 Make sure that the appliance is in setting mode 3 Press and hold function buttons B and C until the indicator lights of function buttons A B and C start to flash 4 Release function buttons B and C 5 Press function button A The indicator lights for function buttons B and C go off The indicator light for function button A continues to flash The digital display shows the current level You can hear an audible signal Example digital display shows G 5 intermittent audible signals level 5 6 Press the function button A one time to increase the water softener level by one step 7 Continue pressing function button A until the desired water softener level is achieved 8 Press the on off button to save the operation Downloaded from DishWasher Manual com Manuals Use of dishwasher salt USE OF DISH
4. Clean the water tap The appliance does not fill with wa The water tap is closed ter Open the water tap e The filter in the water inlet hose is blocked Clean the filter e The installation of the water inlet hose is not correct The hose can be kinked or squashed ake sure that the installation is correct e intermittent audible signal e There is a blockage in the sink spigot the digital display shows 2 7 Clean the sink spigot The appliance will not drain The installation of the water drain hose is not correct The hose can be kinked or squashed Make sure that the installation is correct e intermittent audible signal e Close the water tap and contact your Customer Care Cen e the digital display shows JO fe The anti flood device operates The program does not start e The appliance door is not closed Close the door e Mains plug is not connected Plug in appliance to the mains e The fuse has blown out in the household fuse box Replace the fuse e Delay start is set Cancel the delay start to start the program immediately After the check switch on the appliance The program continues from the point of inter ruption If the malfunction shows again contact your Customer Care Centre If the display shows a fault code not described in the chart contact your Customer Care Centre These data are necessary to help you quickly and correctly e Model Mod Downfoddedusbay mbar Wi G
5. f ry to fill the rinse aid container Refer to Use of rinse aid 1 The indicator light is off while a washing programme operates Digital display The display shows e adjusted level of the water softener e activation deactivation of the rinse aid dispenser only with multitab function on Downloaded from DishWasher Manual com Manuals Control panel B program duration remaining time to the end of the program end of a washing program number of hours in delay start fault codes deactivation activation of the audible signals Delay start button Use the delay start button to delay the start of the washing program with an interval be tween 1 and 19 hours Refer to Select and start a washing program Function buttons Use the function buttons for these operations o set the water softener Refer to Setting the water softener o deactivate activate the audible signals Refer to Deactivation activation of the audible signals o activate deactivate the multitab function Refer to Multitab function o deactivate activate the rinse aid dispenser when multitab function is active Refer to Multitab function o cancel the washing program in progress or a delay start in progress Refer to Select and start a washing program Setting mode The appliance must be in setting mode for these operations To set a washing program To set the water softener level To deactivate activate the
6. 2 e You can only activate or deactivate the rinse aid dispenser when the multitab function is activated To activate deactivate the rinse aid dispenser 1 Switch on the appliance 2 Make sure that the appliance is in setting mode 3 Press and hold function buttons B and C The indicator lights for function buttons A B and C start to flash 4 Press function button B The indicator lights for function buttons A and C go off The indicator light for function button B continues to flash The digital display shows the setting Od Rinse aid dispenser deactivated fal Rinse aid dispenser activated 5 Press function button B again The digital display shows the new setting 6 Switch off the appliance to save the operation To use normal detergent again 1 Deactivate the multitab function Fill the salt container and rinse aid dispenser Adjust the water hardness setting to the highest level Do a washing program without dishes Adjust the water softener to the water hardness in your area Adjust the rinse aid dosage OO ors SELECT AND START A WASHING PROGRAM i Set the washing program with the door ajar The washing program only starts after you close the door Until then it is possible to modify the settings Downloaded from DishWasher Manual com Manuals Select and start a washing program Follow these steps to set and start a washing program 1 Switch on the appliance 2 Make s
7. Maximum 800 kPa 116 psi Place settings 9 Downloaded from DishWasher Manual com Manuals Installation INSTALLATION INSTRUCTIONS INSTALLATION There should be a minimum The hose should not be Fix drain hose max of Remove entire plastic 2mm gap between the top of extended by more than 10mm below the top of membrane from sink trap the dishwasher and 2 metres or water pump the dishwasher spigot amp fit drain hose to spigot underside of bench top out problems may occur with clamp Secure dishwasher with brackets and screws provided DISHWASHER Gap on both sides should be equal amp no greater than 5mm per side If floor is not level adjust levelling legs to suit POWE R S UPPL Y 230 240V 10 Amps Inlet water supply e Cold water pressure 800 kPa max 50 kPa min e Water flow rate 10 L minute min e f cold water pressure is in excess of 800 kPa a pressure reducing valve should be used Check for leaks WARNING Make sure that mains plug is disconnected from the mains socket during installation CAUTION Obey the instructions in the enclosed template to e build in the appliance e install the furniture door e connect to the water supply and drain i Install the appliance under a counter kitchen worktop or sink If a repair is necessary the appliance must be easily accessible for the engineer Put the appliance adjacent to a water tap and drain For
8. a safety valve The water inlet hose is under pressure only while the water is running If there is a leak in the water inlet hose the safety valve interrupts the running water Be careful when you install the water inlet hose JN WARNING e The mains cable is in the double walled inlet hose Do not immerse the water inlet hose or the safety valve in water e Do not attempt to shorten the inlet hose f the water inlet hose or the safety valve is damaged immediately turn off the power and remove the mains plug from the mains socket e Only a qualified Service Engineer can replace the water inlet hose with safety valve AN WARNING Dangerous voltage i In order to pass the safety valve through the kitchen cabinets an opening of at least 45mm x 90mm is needed Water drain hose Use the supplied hose clamp to connect the water drain hose to the sink The highest point of the drain hose must be no more than 60 cm from the floor and must have a continuous fall to the plumbing connection The drain hose can be lengthened using additional lengths and connectors These must be purchased from Electrolux Spare Parts The extension length must not exceed 2 metres The drain hose must be free of kinks and obstructions Remove the sink plug when the appliance drains the water to prevent that the water goes back into the appliance Downloaded from DishWasher Manual com Manuals Electrical connection
9. audible signals To deactivate activate the rinse aid dispenser Press the on off button The appliance is in setting mode when All the program indicator lights are on Press the on off button The appliance is not in setting mode when Only one program indicator light is on A washing program is set It is necessary to cancel the program to go back to the setting mode Refer to Select and start a washing program Audible signals You can hear an audible signal at the end of the washing program during the setting of the level of the water softener when the appliance has a malfunction The activation of the audible signals is set at the factory Do these steps to deactivate the audible signals 1 2 3 4 Switch on the appliance Make sure that the appliance is in setting mode Press and hold function buttons B and C until the indicator lights of function buttons A B and C start to flash Press the function button C Downloaded from DishWasher Manual com Manuals Use of the appliance oO 6 Indicator lights for function buttons A and B go off Indicator light for function button C flashes The digital display shows the setting Ob Audible signals deactivated Ib Audible signals activated The audible signals are activated Press the function button C again The digital display shows the new setting The audible signals are deactivated Switch off the appliance to save the operatio
10. the venting of the appliance only water hoses and mains cable openings are necessary DownldSRe HOSE PASAS EDISE gA Mis adiygtment of its height Installation Make sure that the water inlet hose the drain hose and the mains cable are not kinked or squashed when you insert the appliance Adjust the level of the appliance Make sure that the appliance is level to close and seal the door correctly If the level of the appliance is correct the door does not catch on the sides of the cabinet Loosen or tighten the adjustable feet until the appliance is level Adhesive steam protection foil Fit the steam protection on the front part of the 450 worktop along the entire width mm Fixing to the adjacent units A WARNING Use the supplied brackets to attach the appliance under the worktop or to the adjacent units to prevent injury or damage 1 Fit the supplied angular brackets in the slots on the top of the appliance Downloaded from DishWasher Manual com Manuals Water connection 2 Use the supplied screws to secure the appliance in position upwards or side ways Make sure the screws are tight ened Custom made kick panel For integrated appliances and full stainless steel door appliances We recommend that you make a custom made kick panel that aligns your kitchen cabinets e A notched continuous panel is necessary to pre vent door swing interferenc
11. this warranty unless the defect claimed is due to faulty or defective parts or workmanship Electrolux is not liable in the following situa tions which are not exhaustive The Appliance is damaged by i accident ii misuse or abuse including failure to properly maintain or service iii normal wear and tear iv power surges electrical storm damage or incorrect power supply v incomplete or improper installation vi incorrect improper or inappropriate operation vii insect or vermin infestation The Appliance is modified without authority from Electrolux in writing The Appliance s serial number or warranty seal has been removed or defaced The Appliance was serviced or repaired by anyone other than Electrolux or its Au thorised Service Centres This warranty the contract to which it relates and the relationship between you and Electrolux are governed by the law applicable in the Australian State where the Appli ance was purchased or the law applicable in New Zealand if the Appliance was pur chased in New Zealand Where the Appliance was purchased in New Zealand for busi ness purposes the Consumer Guarantee Act does not apply Limitation of Liability To the extent permitted by law Electrolux excludes all warranties other than as contained in this document Electrolux shall not be liable for any loss or damage whether direct or indirect or consequential arising from your purchase use or non use of the Appliance D
12. Favorit 65411 VI User manual Dishwasher Downloaded from DishWasher Manual com Manuals Contents Thank you for choosing one of our high quality products To ensure optimal and regular performance of your appliance please read this instruction manual carefully It will enable you to navigate all processes perfectly and most efficiently To refer to this manual any time you need to we recommend you to keep it in a safe place And please pass it to any future owner of the appliance We wish you much joy with your new appliance OPERATING INSTRUCTIONS 3 SELECT AND START A WASHING PROGRAM 19 SAFETY INFORMATION 3 Select and start a washing program with Correct use 3 delay start 20 General safety 3 Cancelling a delay start 20 Child safety 3 Interrupting a washing program 20 Installation 4 Cancelling a washing program 20 PRODUCT DESCRIPTION 6 aa oe program 7 CONTROL PANEL 8 Standby mode 21 Digital display 8 WASHING PROGRAMS 23 cise nossa 2 CARE AND CLEANING 26 unction buttons 9 Setting mode 9 Cleaning the filters 26 Audible signals 9 External cleaning 27 Internal cleaning 27 EER INE AERAANG o Long periods of non operation 27 SETTING THE WATER SOFTENER 0 Frost precautions 27 Manual adjustment 1 Moving the machine 27 Electronic adjustment 11 WHAT TO DO IF 28 USE OF DISHWASHER SALT 2 TECHNICAL DATA 29 USE OF RINSE AID 2 INSTALLATION INSTRUCTIONS 30 Adjusting the rinse a
13. WASHER SALT A CAUTION Only use dishwasher salt Types of salt that are not suitable for dishwashers cause damage to the water softener AN CAUTION Grains of salt and salty water on the bottom of the appliance can cause corrosion Fill the appliance with salt before you start a washing program to prevent corrosion Do these steps to fill the salt container 1 Turn the cap anticlockwise to open the salt container 2 Fill the salt container with 1 litre of water only the first operation 3 Use the funnel to fill the salt container with salt 4 Remove the salt around the opening of the salt container 5 Turn the cap clockwise to close the salt container i It is normal that water overflows from the salt container when you fill it with salt USE OF RINSE AID A CAUTION Only use rinse aid specified for dishwashers Do not fill the rinse aid dispenser with other products e g dishwasher cleaning agent liq uid detergent This can cause damage to the appliance i Rinse aid makes it possible to dry the dishes without streaks and stains Rinse aid is automatically added during the last rinsing phase Follow these steps to fill the rinse aid dispenser Downloaded from DishWasher Manual com Manuals Use of rinse aid 1 Press the release button A to open the rinse aid dispenser lt 2 al AIS A Ei Qa 2 Fill the rinse aid dispenser with rinse a
14. and used in Australia or New Zea and and is in addition to and does not exclude restrict or modify in any way any non excludable statutory warranties in Australia or New Zealand Electrolux warrants that when dispatched from an Electrolux warehouse the Appli ance is free from defects in materials and workmanship for the Warranty Period During the Warranty Period Electrolux or its Authorised Service Centre will at no extra charge if your appliance is readily accessible without special equipment and subject to these terms and conditions repair or replace any parts which it considers to be defec tive You agree that any replaced Appliances or parts become the property of Electro ux This warranty does not apply to light globes batteries filters or similar perishable parts Parts and Appliances not supplied by Electrolux are not covered by this warranty Where you are within an Electrolux service area this warranty covers the cost of trans port of the Appliance to and from Authorised Service Centres of Electrolux and travel ing costs for representatives of the Authorised Service Centre to and from your home or business If you are outside an Electrolux service area you will bear these costs For information about whether you are within an Electrolux service area please phone 13 13 49 in Australia or 0800 10 66 10 in New Zealand Proof of purchase is required before you can make a claim under this warranty You may not make a claim under
15. arse filter A 2 microfilter B 3 flat filter C Follow these steps to clean the filters 1 Open the door 2 Remove the lower basket 3 To unlock the filter system turn the handle on the microfilter B approximately 1 4 anti clockwise 4 Remove the filter system 5 Hold the coarse filter A by the handle with the hole 6 Remove the coarse filter from the microfil ter Downloaded from DishWasher Manual com Manuals Care and cleaning 7 Remove the flat filter C from the bot tom of the appliance ike 8 Clean the filters below running water 9 Put the flat filter C in the bottom of the appliance 10 Put the coarse filter A in the microfilter B and push the filters together 11 Put the filter system in position 12 To lock the filter system turn the handle on the microfilter B clockwise until it ocks in position 13 Install the lower basket 14 Close the door i Do not remove the spray arms If the holes in the spray arms become clogged remove remaining parts of soil with a cock tail stick External cleaning Clean the external surfaces of the appliance and control panel with a damp soft cloth Only use neutral detergents Do not use abrasive products scouring pads or solvents acetone etc Internal cleaning Do an inspection at intervals of 3 months Set a washing program for heavily soiled dishes Use detergent
16. at cutlery and dishes do not cover other cutlery and dishes Make sure that glasses do not touch other glasses Put small objects in the cutlery basket Plastic items and pans with non stick coatings can retain water droplets Plastic items do not dry as well as porcelain and steel items e Put light items in the upper basket Make sure that the items do not move A CAUTION Make sure that the spray arms can move freely before you start a washing program A WARNING Always close the door after you load or unload the appliance An open door can be danger ous Lower basket Put saucepans lids plates salad bowls and cutlery in the lower basket Arrange service dishes and large lids around the edge of the basket Downloaded from DishWasher Manual com Manuals Loading cutlery and dishes The rows of prongs in the lower basket can be ad justed flat to load pots pans and bowls Cutlery basket WARNING Do not put long bladed knives in a vertical position Arrange long and sharp cutlery hori zontally in the upper basket Be careful with sharp items Put forks and spoons with the handles down Put knives with the handles up Mix spoons with other cutlery to prevent them nesting together Use the cutlery grids for best washing results If the dimensions of the cutlery prevent use of the cutlery grids you can fold t
17. ay from children There is a risk of suffocation Keep all detergents in a safe area Do not let children touch the detergents Downfod fie FUIL EH aA ASIA AY Hoa CAR ARRANGE OMEN the door is open Safety information Installation Make sure that the appliance is not damaged because of transport Do not connect a damaged appliance If necessary contact the supplier Remove all packaging before first use A qualified and competent person must do the electrical installation A qualified and competent person must do the plumbing installation Do not change the specifications or modify this product Risk of injury and damage to the appliance Do not use the appliance if the mains cable or the water hoses are damaged if the control panel worktop or plinth area are damaged so that you can get access to the inner side of the appliance Contact your local Customer Care Centre Do not drill into the sides of the appliance otherwise damage to hydraulic and electrical components may occur JN WARNING Carefully obey the instructions for electrical and water connections Downloaded from DishWasher Manual com Manuals Safety information Downloaded from DishWasher Manual com Manuals HRW Product description PRODUCT DESCRIPTION Upper basket Water hardness dial Salt container Detergent dispenser Rinse aid dispenser E Rating plate Filters E Lower spray arm EJ Uppe
18. but do not put dishes in the appliance Long periods of non operation Do these steps when you do not use the appliance for a long period 1 Disconnect the mains plug from the mains socket 2 Close the water tap 3 Keep the door open to prevent unpleasant smells 4 Keep the inner side of the appliance clean Frost precautions CAUTION Do not install the appliance where the temperature is below O C The manufacturer is not responsible for damage because of frost If not possible empty the appliance and close the door Disconnect the water inlet hose and remove water from the water inlet hose Moving the machine Do these steps to move the appliance 1 Disconnect the mains plug from the mains socket 2 Close the water tap 3 Remove the appliance and the hoses Downloaded from DishWasher Manual com Manuals What to do if 4 Do not tilt the appliance during transport WHAT TO DO IF The appliance does not start or stops during operation If there is a fault first try to find a solution to the problem yourself Refer to following charts If you cannot find a solution to the problem yourself contact your dealer or the Customer Care Centre A WARNING Switch the appliance off before you do the suggested corrective actions Fault code and malfunction Possible cause and solution e intermittent audible signal e The water tap is blocked or restricted with limescale the digital display shows
19. by mode decreases power consumption to less than 1 watt Three minutes after the end of the program all indicator lights go off and the digital dis play shows one horizontal bar Press one of the buttons not the on off button to go back to end of program mode Downloaded from DishWasher Manual com Manuals Select and start a washing program Downloaded from DishWasher Manual com Manuals Washing programs WASHING PROGRAMS Washing programs Degree of soil Type of load Program description INTENSIV CARE 70 Heavy soil Crockery cutlery Prewash pots and pans Main wash up to 70 C 2 intermediate rinses Final rinse Drying AUTO MATIC 2 Any Crockery cutlery Prewash pots and pans Main wash up to 50 C or 65 C 1 or 2 intermediate rinses Final rinse Drying 30 MIN 3 Normal or light soil Crockery and cut Main wash up to 60 C lery Final rinse Partial load ECO 50 4 Normal soil Crockery and cut Prewash lery Main wash up to 50 C 1 intermediate rinse Final rinse Drying Yas Normal or light soil Delicate crockery ain wash up to 45 C and cutlery 1 intermediate rinse Final rinse Drying 1 This program includes the sanitize function that gives more hygiene to dishes and glasses In the last rinse the temperature increases to 68 C and is kept above 65 C for minimum 10 minutes 2 During the AUTO MATIC program the soil level of the dishes is given by how cloudy the water is The program duration and co
20. d If the mains cable has to be The mains plug must be accessible after the appliance has been installed Never unplug the appliance by pulling on the cab Test the appliance Run a quick washing program water washes and drains with no leaks e Always pull the plug and ensure that the appliance fills with The manufacturer accepts no liability for failure to observe the above safety precautions Downloaded from DishWasher Manual com Manuals Environment concerns ENVIRONMENT CONCERNS The packaging materials are environmentally friendly and can be recycled The plastic com ponents are identified by markings e g gt PE lt gt PS lt etc Discard the packaging materials in the applicable container at the community waste disposal facilities A WARNING To discard the appliance follow the procedure e Pull the mains plug out of the socket e Cut off the mains cable and mains plug and discard them e Discard the door catch This prevents children closing themselves inside the appliance and endangering their lives Old appliance Make sure that the appliance goes to the applicable collection point for recycling Make sure that this appliance is discarded correctly Inappropriate waste discard of the ap pliance causes negative consequences for the environment and human health For more information about the recycling of this appliance contact your local city office your household waste disposal service or th
21. e and to keep kick panel alignment with adjacent units e Cut a notch in the kick panel sufficient to let the door swing freely under the appliance e Make a check for interference Open and close the door slowly If the door touches the kick panel trim to prevent interference Attach the kick panel to adjacent cabinets so that if service is necessary you can remove it ao E WATER CONNECTION Water inlet hose Connect the appliance to a cold water supply Connect the inlet hose to a water tap with an externa A CAUTION Always use new hoses when you connect the appliance not be used The water inlet hose must be examined a deterioration and replaced if necessary The water pressure must be in the limits refer to Tech water authority gives you the average mains pressure Downloaded from DishWasher Manual com Manuals BSP thread spout of 3 4 e to the water mains Old hoses must an interval of twelve months for nical data Make sure that the local in your area Water connection Make sure that there are no kinks in the water inlet hose and that the water inlet hose is not squashed or entangled Fit the hose nut correctly to prevent water leaks AN CAUTION Do not connect the appliance to new pipes or pipes that have been not used for a long time Let the water run for some minutes then connect the inlet hose The water inlet hose is double walled and has an inner mains cable and
22. e shop where you purchased the appliance WARRANTY Electrolux FOR SALES IN AUSTRALIA AND NEW ZEALAND This document sets out the terms and conditions of product warranties for Electro lux branded appliances It is an important document Please keep it with your proof of purchase documents in a safe place for future reference should you require serv ice for your Electrolux appliance General Terms and Conditions 1 In this warranty Electrolux means Electrolux Home Products Pty Ltd ABN 51 004 762 341 in respect of Appliances purchased in Australia and Electrolux NZ Limited in respect of Appli ances purchased in New Zealand Appliance means any Electrolux product purchased by you accompanied by this document Warranty Period means i where you use the Appliance for personal domestic or household purposes in Australia the period of 24 months and in New Zealand the period of 24 months ii where you use the Appliance for commercial purposes in Australia the period of 0 months and in New Zealand the period of 0 months if the period stated is 0 months you are not covered by this product warranty following the date of original purchase of the Appliance you means the purchaser of the Appliance not having purchased the appliance for re sale and your has a corresponding meaning Downloaded from DishWasher Manual com Manuals Warranty 10 This warranty only applies to Appliances purchased
23. hem out You can open the cutlery basket to remove the cutlery more easily Follow these steps to remove the cutlery 1 Put the cutlery basket on a table or work surface 2 Open the handle 3 Remove the cutlery i Hold the two parts of the handle tightly when you move the cutlery basket Downloaded from DishWasher Manual com Manuals Loading cutlery and dishes Upper basket The upper basket is for plates maximum 24 cm in diameter saucers salad bowls cups glasses and lids Arrange the items to let water touch all surfaces e For longer items fold the cup racks up Adjustment of the height of the upper basket If you put large plates in the lower basket first move the upper basket to a upper position Maximum height of the dishes in Po the upper basket the lower basket Upper position 20 cm Lower position 24 cm 31 cm 27 cm Follow these steps to move the upper basket to the upper position Downloaded from DishWasher Manual com Manuals Use of detergent 1 Pull the basket out until it stops 2 Carefully lift the two sides until the mechanism is engaged and the basket is stable Follow these steps to move the upper basket to the lower position 1 Pull the basket out until it stops 2 Carefully lift the two sides upwards 3 Hold the mechanism and g
24. id The mark max shows the maximum level 3 Remove the spilled rinse aid with an ab sorbent cloth to prevent too much foam during the subsequent washing program 4 Close the rinse aid dispenser Adjusting the rinse aid dosage The rinse aid is set at the factory at position 4 You can set the rinse aid dosage between position 1 lowest dosage and position 6 highest dosage Turn the rinse aid dial to increase or decrease the dosage Increase the dosage if there are water droplets or limescale on the dishes Decrease the dosage if there are streaks whitish stains or bluish layers on the dishes i Wash hands to remove any residue of rinse aid from skin Downloaded from DishWasher Manual com Manuals Loading cutlery and dishes LOADING CUTLERY AND DISHES Helpful hints and tips Only use the appliance for household utensils that are suitable for dishwashers Do not use the appliance to clean objects that can absorb water e g sponges household cloths e Before you load cutlery and dishes follow these steps Remove all food remainings and debris Make burnt remaining food in pans soft e While you load cutlery and dishes follow these steps Load hollow items e g cups glasses and pans with the opening down Make sure that water does not collect in the container or in a deep base Make sure that cutlery and dishes do not lie inside one another Make sure th
25. id dosage 3 INSTALLATION 30 LOADING CUTLERY AND DISHES t Adjust the level of the appliance 31 Helpful hints and tips 4 Adhesive steam protection foil 31 Lower basket 14 Fixing to the adjacent units 31 a gt Custom made kick panel 32 pper baske Adjustment of the height of the upper WALER SONNECTION a basket 16 ea He i ater drain hose USE OF DETERGENT 7 ELECTRICAL CONNECTION 34 ee ENVIRONMENT CONCERNS 35 To activate the multitab function 9 To activate deactivate the rinse aid Old appliance 35 dispenser 9 WARRANTY 35 Subject to change without notice Downloaded from DishWasher Manual com Manuals Safety information OPERATING INSTRUCTIONS N SAFETY INFORMATION i For your safety and correct operation of the appliance read this manual carefully before installation and use Always keep these instructions with the appliance even if you move or sell it Users must fully know the operation and safety features of the appliance Correct use Only use the appliance to clean household utensils that are suitable for dishwashers Do not put solvents in the appliance Risk of explosion Put the knives and all items with sharp points in the cutlery basket with their points down If not put them in a horizontal position in the upper basket e Use only products specified for dishwashers detergent salt rinse aid If you open the door while the appliance is in operation hot steam can escape Risk of skin burns Do not remo
26. ler Manual com Manuals Technical data e Serial number S N For these data refer to the rating plate Write the necessary data here Model description Product number Serial number The cleaning results are not satisfactory The dishes are not clean Limescales particles on the dishes The dishes are wet and dull There are streaks milky spots or a bluish coating on glasses and dishes Dry water drop stains on glasses and dishes TECHNICAL DATA Dimensions Electrical connection Voltage Overall power Fuse Water supply pressure Capacity The selected washing program is not applicable for the type of load and soil The baskets are loaded incorrectly so that water cannot reach all surfaces Spray arms do not turn freely because of incorrect arrangement of the load The filters are dirty or not correctly installed The quantity of detergent is too little or missing The salt container is empty The water softener is adjusted on a wrong level The salt container cap is not closed correctly e No rinse aid has been used The rinse aid dispenser is empty Decrease the rinse aid dosage Increase rinse aid dosage The detergent can be the cause Width mm 446 Height mm 818 898 Depth mm 550 Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door Minimum 50 kPa 7 psi
27. n Do these steps to activate the audible signals 1 Do the above procedure until the digital display shows necessary setting USE OF THE APPLIANCE Refer to specified instructions for each step of the procedure 1 Check if the water softener level is correct for the water hardness in your area If neces sary set the water softener 2 Fill the salt container with dishwasher salt 3 Fill the rinse aid dispenser with rinse aid 4 Load cutlery and dishes into the dishwasher 5 Set the correct washing program for the type of load and soil 6 Fill the detergent dispenser with the correct quantity of detergent 7 Start the washing program SETTING THE WATER SOFTENER The water softener removes minerals and salts from the water supply Minerals and salts can have bad effect on the operation of the appliance Water hardness is measured in equivalent scales e mg l millimol per litre ppm parts per million e mmol l millimol per litre international unit for the hardness of water Adjust the water softener in to the water hardness in your area If necessary contact your local water authority Water hardness Water hardness setting 10 910 1250 910 1250 Qi 125 2 760 909 760 909 7 6 9 0 2 9 650 759 650 759 05 76 2 8 510 649 510 649 5 1 6 4 2 7 Downloaded from DishWasher Manual com Manuals Setting the water softener JN Water hardness Water hardness Sue 400 509 400 509 4 0 5 0
28. nsumptions can change This depends if the appliance is fully or not and on the level of soil on the dishes The appliance adjusts automatically the temperature of the water during the main wash 3 This is the perfect daily program to clean a partial load Ideal for a family of 4 persons who only want to load breakfast and dinner crockery and cutlery 4 Test program for test institutes Please refer to separate leaflet supplied for test data Consumption values Energy in kWh Water in litres INTENSIV CARE 70 1 3 1 5 14 15 AUTO MATIC 0 8 1 3 10 19 30 MIN 0 8 8 ECO 50 0 8 0 9 12 13 Vase 0 6 0 7 lil 12 1 The digital display shows the program duration Downloaded from DishWasher Manual com Manuals Washing programs i The pressure and temperature of the water the variations of power supply and the quantity of dishes can change these values Downloaded from DishWasher Manual com Manuals Washing programs Downloaded from DishWasher Manual com Manuals Care and cleaning CARE AND CLEANING WARNING Switch the appliance off before you clean it Cleaning the filters CAUTION Do not use the appliance without the filters Make sure that the installation of the filters is correct Incorrect installation will cause unsatisfactory washing results and damage to the appliance If necessary clean the filters Dirty filters decrease the washing results The dishwasher has three filters 1 co
29. ortant Notice Before Calling a Service Technician please check carefully the operating instructions service booklet and the warranty terms and conditions FOR SERVICE OR TO FIND THE ADDRESS OF YOUR NEAREST STATE SERVICE CENTRE IN AUSTRALIA Please call 13 13 49 For the cost of a local ca Australia only FOR SERVICE OR TO FIND THE ADDRESS OF YOUR NEAREST AUTHORISED SERVICE CENTRE IN NEW ZEA LAND Free call 0800 10 66 10 New Zealand only SERVICE AUSTRALIA A Electrolux ELECTROLUX HOME PROD UCTS SERVICE NEW ZEALAND Electrolux ELECTROLUX HOME PROD UCTS Downloaded from DishWasher Manual com Manuals FOR SPARE PARTS OR TO FIND THE ADDRESS OF YOUR NEAREST STATE SPARE PARTS CENTRE IN AUSTRALIA Please call 13 13 50 For the cost of a local call Australia only FOR SPARE PARTS OR TO FIND THE ADDRESS OF YOUR NEAREST SPARE PARTS CENTRE IN NEW ZEALAND Free call 0800 10 66 20 New Zealand only Downloaded from DishWasher Manual com Manuals Downloaded from DishWasher Manual com Manuals www aeg electrolux com shop e A e 4 J 117960262 B 412010 ownloaded from DishWasher Manual com Manuals CE
30. ownloaded from DishWasher Manual com Manuals 11 Provisions of the Trade Practices Act and State consumer legislation in Australia and the Consumer Guarantees Act the Sale of Goods Act and the Fair Trading Act in New Zealand imply warranties or conditions or impose obligations upon Electrolux which cannot be excluded restricted or modified To the extent permitted by law the liability of Electrolux if any arising out of or in relation to the Appliance or any services sup plied by Electrolux shall be limited where it is fair and reasonable to do so in the case of Appliances at its option to the replacement or repair of the Applian ces or the supply of equivalent products or the payment of the cost of replacing the Appliances or having the Appliances repaired or of acquiring equivalent Appliances Upon being replaced parts and Appliances become the property of Electrolux or in the case of services at its option to the supply of the services again or the pay ment of the cost of having the services re supplied and in the case of Appliances or services supplied in New Zealand loss or damage whether direct or indirect or consequential that is reasonably foreseeable Privacy You acknowledge that in the event that you make a warranty claim it will be necessary for Electrolux and its Authorised Service Centres to exchange information in relation to you to enable Electrolux to meet its obligations under this warranty Imp
31. r spray arm Light beam After the start of the washing program a light beam shows on the floor below the appli ance door If the appliance is installed higher with a flush kitchen furniture door the light beam will not be visible Light beam The red light is on Indication of the start of a washing program The red light stays on dur ing the washing program The red light flashes Indication of a malfunction The red light goes off Indication of the end of a washing program Downloaded from DishWasher Manual com Manuals Product description Downloaded from DishWasher Manual com Manuals BEEBE Control panel CONTROL PANEL INTENSIV AUTO 30 ECO Das E MULTITAB CARE 70 m MATIC m MIN 50 I EES REST MUTE INTENSIV AUTO 30 ECO E MULTITAB Dw CARE 70 MATIC MMN 50 a 745 e On off button Digital display Delay start button Program selection buttons Indicator lights E Program indicator lights Function buttons Indicator lights MULTITAB The indicator light shows the activation deacti vation of the multitab function Refer to Multi tab function g 1 The indicator light comes on when it is necessa ry to fill the salt container Refer to Use of dish washer salt The salt indicator light can stay on for some hours but it does not have an unwanted effect on the operation of the appliance 3 1 The indicator light comes on when it is necessa
32. titab function is for combi detergent tablets These tablets contain agents such as detergent rinse aid and dishwasher salt Some types of tablets can contain other agents Do a check if these tablets are suitable for the local water hardness Refer to the instruc tions from the manufacturer The multitab function can be set with any program When you set the multitab function it stays on until you deactivate it The multitab function automatically stops the rinse aid and water softener operation The rinse aid indicator light and salt indicator light are deactivated The program duration can increase if you use the multitab function Downloaded from DishWasher Manual com Manuals Select and start a washing program RE Activate or deactivate the multitab function before the start of a washing program You cannot activate or deactivate the multitab function when the program operates Can cel the washing program then set the program again To activate the multitab function e Press and hold the two multitab buttons function buttons D and E The multitab indica tor light comes on To deactivate the multitab function e Press and hold the two multitab buttons function buttons D and E The multitab indica tor light goes off i Follow these steps if the drying results are not satisfactory 1 Fill the rinse aid dispenser with rinse aid 2 Activate the rinse aid dispenser 3 Set the rinse aid dosage to position
33. uide it back down slowly CAUTION e Do not lift or lower the basket on one side only e If the basket is in the upper position do not put cups on the cup racks USE OF DETERGENT i Only use detergents powder liquid or tablet that are suitable for dishwashers Follow the data on the packaging e dosage recommended by the manufacturer e storage recommendations W Do not use more than the correct quantity of detergent to decrease pollution Follow these steps to fill the detergent dispenser 1 Open the lid of the detergent dispenser 2 Fill the detergent dispenser A with deter gent The marking shows the dosage 20 approximately 20 g of detergent 30 approximately 30 g of detergent Downloaded from DishWasher Manual com Manuals HEE Multitab function 3 If you use a washing program with pre wash put more detergent in the prewash detergent compartment B 4 If you use detergent tablets put the deter gent tablet in the detergent dispenser A 5 Close the lid of the detergent dispenser Press the lid until it locks into position i Different brands of detergent dissolve in different times Some detergent tablets do not have the best cleaning results during short washing programs Use long washing programs when you use detergent tablets to fully remove the detergent MULTITAB FUNCTION The mul
34. ure that the appliance is in setting mode 3 Press one of the program buttons Refer to the Washing programs chart for program details The indicator light of the selected program stays on All other program indicator lights go off The digital display shows the program duration 4 Close the door The washing program starts i When the washing program operates you cannot change the program Cancel the washing program Refer to Cancelling a washing program Select and start a washing program with delay start 1 Press the on off button 2 Seta washing program The program indicator light comes on 3 Press the delay start button until the display shows the necessary delay start of the washing program The delay start indicator light comes on 4 Close the door The countdown of the delay start starts When the countdown is completed the washing program starts automatically i If you open the door during the countdown it will interrupt the countdown When you close the door again the countdown continues from the point of interruption Cancelling a delay start 1 Press and hold function buttons B and C until all the program lights come on When you cancel a delay start you also cancel the washing program 2 Set anew washing program A WARNING Only interrupt or cancel a washing program if necessary Open the door carefully Hot steam and water can escape Interrupting a washing program
35. ve dishes from the appliance before the end of the washing program When the washing program is completed disconnect the mains plug from the mains socket and close the water tap Only an authorised service engineer can repair this appliance Use only original spare parts Do not do repairs yourself to prevent injury and damage to the appliance Always con tact the Customer Care Centre General safety Some dishwasher detergents are strongly alkaline They can be extremely dangerous if swallowed Avoid contact with skin and eyes Keep the children away from the appliance when the door is open Check that the detergent dispenser is empty after completion of the washing programme Obey the safety instructions from the manufacturer of the dishwasher detergent to pre vent burns to eyes mouth and throat e Only put detergent in the dispenser before you start a washing program e Do not drink the water from the appliance Detergent residues can stay in your appli ance Always close the door when you do not use the appliance to prevent injury and not to stumble over the open door Do not sit or stand on the open door Child safety This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely Young children should be supervised to ensure that they do not play with the appliance Keep all the packaging aw
Download Pdf Manuals
Related Search