BWD1409W 60 cm 9 kg Freestanding washer dryer
Contents
1. o Pre washing helps to loosen soil before the main wash 28 Stain removal rules o Use warm water for soaking or pre washing stained laundry Hot water can set stains o Most stains are easier to remove when they are fresh o Before treating any stain try to establish what kind of stain it is how old the stain is what the fabric type is and whether the fabric is colourfast check the care label to find this out o Washing and drying can fix some stains o When bleach is recommended use a mild fabric bleach that is safe for the fabric o If you need to use a stain remover put the stained area face down on a paper towel or white cloth Apply the stain remover to the back of the stain This forces the stain off the fabric instead of through it Stain removal guide STAIN TO REMOVE Blood Rinse immediately in COLD water If the stain remains soak in cold water with an enzyme pre wash Chewing gum Use ice in a plastic bag to harden the gum Scrape off what you can and then sponge with white spirit Chocolate Sponge with COLD water and then soak in an enzyme pre Cocoa wash If stains persist rub in a little detergent and then rinse in cold water Coffee Blot up quickly and then rinse out in COLD water Rub in a little detergent and then machine wash at the maximum temperature allowed according to the wash care label Ice cream If the stain is still apparent sponge with white spirit Deodorant Rub the affec2. 21 IMPORTANT If you are draining water from the bail hose and drain pump filter in an emergency You should take care as the water coming from the machine mid cycle could be hot Especially if the water is being drained in the middle of one of the hotter wash cycles Cleaning the water inlet filter o Clean the filter when water leaks from the water inlet o Always pull the power plug out before cleaning o Turn off the water supply to the washer and separate the inlet hose o Pull the inlet filter out Remove the dirt from the inlet filter with a brush and replace Winter storage o You should install your appliance in a location where it will not be subjected to freezing temperatures o If you are going to store your appliance in a location where the temperature will drop below freezing in winter then you should follow the table below To winterize the washer To use the washer again e Turn off the water supply e Flush the water pies e Disconnect and drain the water and hoses inlet hoses e Reconnect the water e Run the washer on a drain and inlet hoses spin setting for one minute e Turn on the water e Unplug the power supply cord supply e Reconnect the power supply cord Removing stains Garments that are covered in stains grease or are heavily soiled may need to be pre washed or soaked before being placed inside of the washer dryer o Soaking helps to remove protein type stains like blood milk or grass
3. Error code failure system General troubleshooting Contact details Environmental note Ihis appliance is marked according to the European directive 2002 96 EC on Waste electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product Ihe symbol iis on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office vour household waste disposal service or the shop where you purchased the product o The packaging materials that Baumatic uses are environmentally friendly and can be recycled o Please discard all packaging material with due regard for the environment I mportant safety information Your safety is of the utmost importance to Baumatic Please make sure that you read this instruction booklet before attempting to install or use the appliance If you are unsure of any of the information contai
4. USER MANUAL FOR YOUR BAUMATIC BWD1409W 60 cm 9 kg Freestanding washer dryer S a Baumatic NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a safe place so that it is easily available for future reference for you or any person not familiar with the operation of the appliance GS 25 05 10 Contents Environmental note I mportant safety information Specifications Description of the appliance Control panel LCD display Detergent drawer Preparing the wash cycle Preparing your garments for washing A selection of wash care symbols Detergents and conditioners Wash program table Wash program guidance Selecting a wash program Descriptions of the wash programs End of cycle Pausing a wash program Changing a wash program Delay start feature Child lock Maintenance and cleaning In daily use Control panel and washer dryer cabinet Detergent drawer The washer dryer drum Door 95 maintenance wash Cleaning the drain pump filter Cleaning the water inlet filter Winter storage Removing stains Stain removal rules Stain removal guide Poor wash results I nstallation Removing the transit bolts Locating your washer dryer Connecting to the mains water supply Connecting to the water outlet Levelling the appliance Power supply Before first use maintenance wash
5. and close the door Put the detergent into the main wash compartment and prewash compartment in the detergent drawer Softener should be below the MAX level Only put detergent into the prewash compartment if you want to add a prewash to your cycle When you want to use bleach put this in the main wash compartment with the detergent Press the power button 1 and the LED display will show Press the delay start button 9 If you press the start pause button 2 next without selecting a program the cotton wash is selected as a default wash cycle Alternatively you can select a wash using the wash program selection dial 3 and you can also alter the temperature 4 and spin speed 5 by pressing the relevant buttons Select the time delay you require by pressing the time delay button 9 You can choose between 2 to 12 hours and the displayed time will show the program s finishing time The finishing time may vary depending on your selected temperature Press the start pause button 2 The time delay LED should light The delicate quick 20 tub clean and drain programs cannot be selected using the time delay function You also cannot add clothes during a time delay cycle 24 Child lock Your appliance has a child lock option if this is set it will mean that nobody can affect the operation of the wash program once it has started o To activate the child lock press and hold the wash button 6 and the temperatur
6. is provided with the appliance Your appliance should only be connected to a cold water supply For an ordinary tap 1 Pull down the collar of the 2 Loosen the four screws 3 Fit the water tap adapter inlet hose to separate it slightly in order to fit the onto the water tap and from the water tap adapter onto the water tap tighten the four screws adapter evenly whilst pushing up the adapter so that the rubber seal can stick to the water tap tightly M eb P 6 4 Remove the tape and 5 Connect the inlet hose to 6 Connect the other end of tightly screw connector B the water tap adapter by the hose to the water inlet into connector A pulling down the collar on on the rear of the washer the end of the hose by turning it clockwise until it is tight Check that the rubber seal is present inside the inlet hose adapter on this end of the hose cx E g 33 For a screw shaped tap 1 Connect the inlet hose to your 2 Connect the other end of M the hose to the water inlet seals must be present on bo n tha mar nf the of the connectors Otherwise Dv ine washer there may be a leak y turning it clockwise until it is tight Water tap 4 cA Rubber AN seal i 1 4 N HE C Rubbi E gt Seal Check that the rubber seal Inlet is present inside the inlet hose hose Connector adapter on this end of the hose Connecting to the water outlet v Secure the d
7. only if you want to use the pre wash option Softener should be poured into the middle compartment of the detergent drawer the level should be below the MAX level If you want to use bleach then you should put it into the main wash compartment with your detergent Press the power button 1 the LCD display will show and all the program lights will come on Use the wash program selection knob 3 to select the synthetic program A wash temperature of 309C with an 800 rpm spin will be selected automatically by the appliance You can use the temp button 4 to adjust the wash temperature cold 30 C and 40 C wash temperatures are available You can use the spin button 5 to adjust the spin speed A 1400 rpm spin speed is not available with the synthetic wash program You can use the wash button 6 to select a pre wash or soak and the rinse button 11 can be pressed to program a rinse Press the start pause button 2 the door will lock and after a few seconds you will hear the machine start to fill with water 18 Delicate handwash program O Put the laundry into the drum and then close the door The maximum wash load size is below 3kg for the delicate program In the detergent drawer put detergent into the main wash compartment Softener should be poured into the middle compartment of the detergent drawer the level should be below the MAX level If you want to use bleach then you should
8. put it into the main wash compartment with your detergent Press the power button 1 the LCD display will show and all the program lights will come on Use the wash program selection knob 3 to select the delicate program A wash temperature of cold with a 400 rpm spin will be selected automatically by the appliance The wash temperature of cold is not adjustable for the delicate wash program You can use the spin button 5 to adjust the spin speed 1400 and 1000 rpm spin speeds are not available with the delicate wash program You can use the rinse button 11 to select the rinse cycle option Press the start pause button 2 the door will lock and after a few seconds you will hear the machine start to fill with water 19 Intensive program O Put the laundry into the drum and then close the door Put detergent into the main wash and pre wash compartments in the detergent drawer Softener should be below the MAX level Put detergent into the pre wash compartment only if you want to add pre wash When you want to use bleach put it into the main wash compartment with detergent Press the power button 1 The LED shows only and all program lights will turn on Use the wash program selection knob to select the intensive program Select the intensive program using the program selection dial 3 The machine will set a washing temperature of 60 C and a spin speed of 1000rpm If you want
9. s the drain hose placed higher than 1m above floor Error display 573 Vibrating and too noisy s the washer installed on an uneven floor Have all the transit bolts removed o If IE LE OE or UE are displayed on the LED display you should turn the appliance off using the POWER button and then switch it back on again using the POWER button o If PFE is displayed on the LED display you should turn the appliance off using the POWER button switch it back on again using the POWER button press the SPIN button and then press the START PAUSE button 37 If a fault code reappears after following the above advice and clearing the fault code You should turn the washer dryer off using the POWER button Disconnect the appliance from your mains supply Then arrange for an engineer to attend the appliance You should contact the Baumatic Customer Care Department on 0118 933 6911 IF AN ENGINEER ATTENDS DURING THE GUARANTEE PERIOD AND FINDS THAT A FAULT HAS BEEN CAUSED BY AN ITEM ON THE ERROR CODE LIST WHICH COULD HAVE BEEN CLEARED BY THE CUSTOMER THEN YOU MAY BE LIABLE FOR THE COST OF THE SERVI CE CALL General troubleshooting Water under the washer dryer o Tighten the drain pump filter o Check the drain and inlet hose and make sure that they are fully tightened Washer dryer vibrates during the spin cycle o Check that the transport locking devices have been removed see installation instructions o Ma
10. will be operated with a locked door and supplied water Press the power button 1 the LCD display will show and all the program lights will come on Use the wash program selection knob 3 to select the drain program Press the start pause button 2 the door will lock and after a few seconds you will hear the machine start to drain I MPORTANT Please note that the appliance will not spin on this particular wash cycle Tub clean program O O Dry Press the power button 1 and the LED will show only Select the tub clean program using the program selection dial 3 The machine will automatically set a soak program and a spin speed of 400 rpm and a cold water temperature Put the laundry into the drum and close the door The maximum load size for a drying cycle is 7 kg Press the power button and the LED will show Select the level of dryness you want by pressing the dry button Continue pressing the dry button if you want to set a length of time for a drying cycle Once the display has scrolled through the cycles you can select a time ranging from 1 to 4 hours 22 O Press the start pause button 2 and the machine will begin the cycle after a few seconds For approximate drying times for each cycle see the table below Drying Cycle Approximate Time hr min 01 00 04 00 Low temperature 01 40 01 30 Cupboard 03 30 04 30 It is possible to select a separate drying cycle o
11. The washer dryer automatically selects a temperature for a particular wash program However it is possible to alter the temperature by using the temp button All temperatures will not be available on certain wash programs o The washer dryer automatically selects a spin speed for a particular wash program However it is possible to alter the spin speed by using the spin button All spin speeds will not be available on certain wash cycles o Important You should make sure that the selected spin speed is appropriate for the garments that you are washing o Important Before opening the door of the appliance you MUST spin the clothes and drain the water See the section called Spin only o The active phases will appear at the top of the LED display as the wash program progresses o The LCD display shows an approximate time for the selected wash cycle Please note that factors external to the machine e g the temperature of your water supply your water pressure etc can affect the time it takes for a wash cycle to complete 16 Selecting a wash program Cotton program o Put the laundry into the drum and then close the door The maximum load size is 9kg for a cotton wash o In the detergent drawer put detergent into the main wash and pre wash compartments o Put detergent into the pre wash compartment only if you want to use the pre wash option o Softener should be poured into the middle compartment of the detergent drawe
12. ains on them o The garments are soiled with oils ointments or grease and were washed without enough detergent o The wash temperature selected was too low o Fabric conditioner has come into contact with the garments If this happens try to wash out these stains as quickly as you can and try to avoid getting conditioner on the garments in future 30 After the final rinse can still see foam o Modern detergents can result in there still being foam in the final rinse this does not mean that the washing is not being rinsed properly There is white residue on my garments when remove them from the appliance Modern detergents can contain insoluble contents white residue after a wash cycle is not necessarily a sign of the garments being insufficiently rinsed by the washer dryer O o You should shake out the garment or brush it off In future possibly turn the garment inside out before it is washed You may wish to move from a powder detergent and switch to a liquid detergent instead Installation IMPORTANT THIS INSTALLATION MUST BE COMPLETED BY A SUITABLY QUALIFIED PERSON BAUMATIC ONLY SANCTION THE INSTALLATION GIVEN IN THIS INSTRUCTION MANUAL YOU SHOULD KEEP THE TRANSIT PACKAGING IN CASE YOU NEED TO TRANSPORT THE MACHINE IN THE FUTURE Removing the transit bolts IMPORTANT Before installing or operating the washer dryer YOU MUST remove the transit bolts that hold the drum in position whilst th
13. are labels indications o The wash care symbols should be used to help you to select the most suitable wash program They will also help you to sort your laundry into different loads depending on the fabric type and the highest temperature which the garment can be washed at Detergents and conditioners The amount of detergent that you need to use in your appliance will depend on o The degree of soiling Lightly soiled garments in general require less detergent o The size of the wash load A smaller wash load will require a reduction in the amount of detergent o The hardness of your tap water The harder your water is then the more detergent you will need to use The detergent manufacturers normally give guidance as to how much extra detergent should be used depending on the hardness of the water 14 Liquid detergent If you are using liquid detergent then in the majority of cases the liquid should be placed inside the dosing device supplied by the detergent manufacturer and placed inside the drum All instructions on the detergent packaging should be followed Water softening agents If your tap water is hard then it may be prudent to utilise a water softening agent This will help to ensure that the appliance does not become clogged with hard water deposits You may also find that it will allow you to lessen the amount of detergent that you are using When using any detergent or water softening agent the recommendat
14. code may appear on the LCD display The following error codes can possibly be remedied by the customer and the steps outlined below should be followed BEFORE COMPLETING ANY MAINTAINEANCE ON THE APPLIANCE IT SHOULD BE DISCONNECTED FROM YOUR POWER SUPPLY PROBLEM CHECK POINT The washer will not s there a power failure operate at all s the power cord correctly connected to the electrical outlet Did you tum on the power Did you press the Start Pause button s there the correct amount of laundry in the washer Water is not supplied Did you connect the inlet hose and open the water tap Error dispiay IEA s the inlet hose or the water tap frozen s the water supply shut off s there any foreign matter blocking up the inlet hose filter The washer will not drain Is the drain hose frozen or blocked by dirt Eror display r3 s the drain hose kinked or deformed s the end of the drain hose immersed in water s there excessive dirt inside the drain filter The washer will not spin Are the clothes in the drum collected on one side Zar s the washer installed on an uneven floor or is there serious Error display a Win vibration s the door open The lamp TE will light up in this case The washer will stop s the filter of the drain pump clogged during spinning s the drain pump operating Spinning is insufficient Did you use the proper amount of detergent oe
15. ction on wash care symbols Your washing should also be sorted out according to the degree of soiling Check all pockets on a garment to make sure that they are empty Remove any detachable metal items badges paperclips safety pins etc Zips should be closed duvet covers and pillow cases should be buttoned up and any loose straps should be tied up This will help to prevent other garments from getting damaged during the wash Woollens and knitted coloured fabrics should be turned inside out before being washed in the appliance Small delicate items tights baby socks should be placed in either a washing net or a zipped pillow case Curtains should be handled with particular care All plastic hooks or metal strips must be removed before being washed in the appliance Coloured items and whites should be washed in separate wash cycles New garments often contain an excess of dye therefore it is advisable to wash them separately for their first wash Garments should be unfolded and shook out before being placed inside the machine 13 A selection of wash care symbols Washing boiling normal normal Do not temp 95 C temp 60 C temp 40 C wasch xl delicate manual ll Dry cleaning ka Do not all solvents all but TRI Benzine only clean Do not Ill Spin dryer normal OW high dry I Dia not 110 C 150 C 20010 iran IV Ironing N select a programme taking into account the c
16. d leave the porthole door open for a short period of time Cleaning the drain pump filter IMPORTANT Switch off your washer dryer and disconnect the plug from your mains supply You should clean out the filter approximately every ten washes If the drain pump filter is not cleaned regularly then your appliance may find it difficult to pump out water efficiently o You should regularly check to see if any deposits have formed or there are any foreign bodies in the drain pump filter o Locate the drain pump filter flap that is on the base of the appliance in the front right hand corner o Use a coin to open the drain pump filter flap o Pull out the bail tube that is to the left of the drain pump filter Place the end of the tube into an adequately sized bowl and then remove the cap from the end of it o When water no longer runs out of the bail tube you can turn the drain pump filter cover anti clockwise This will allow you to remove the drain pump filter from its housing o Remove any debris from the drain pump filter by running it under a tap o After cleaning reinsert the drain pump filter into its housing Tighten the drain pump filter by turning it clockwise you should keep tightening it until you cannot turn it any further o Reinsert the cap into the end of the bail hose making sure that it is securely in place Slide the bail hose back into its original position and then close the drain pump filter flap
17. e appliance is being transported o On the rear of the appliance identify the 4 transit bolts 3 o Using the spanner supplied unscrew the 4 transit bolts o You should keep the 4 transit bolts and spanners in case you need to transport the appliance elsewhere in future o Cover the holes that you removed the transit bolts from using the 4 transit covers supplied Drain Hose Washer 4 o Before commencing installation check i the location where you intend to install the appliance You should make sure that you have everything in place that is Laundry necessary for the correct installation o Do not place or store your washer dryer in a location where the ambient temperature could fall below O C otherwise the water in it could freeze up o Never place or store laundry products on top of the appliance o Install the washer on a flat solid floor If the washer is installed on an uneven or suspended floor it could cause excessive noise and severe vibration which may result in the malfunction of the appliance o You should also level off the washer dryer using the adjustable feet on the base of the appliance 32 o There should be a gap of 2 cm either side of the washer dryer a 10 cm gap should be left behind the appliance Connecting to the mains water supply IMPORTANT The washer dryer should never be connected to the water mains using an existing inlet hose YOU MUST utilise the inlet hose that
18. e button 4 at the same time for approximately three seconds o Follow the same steps to deactivate the child lock Maintenance and cleaning I n daily use o Once a wash cycle has completed you should pull out the detergent drawer slightly so it can dry out o Leave the porthole door ajar for a short while after a wash cycle has completed This should help to prevent stagnant smells and to protect the door seal o Close the water tap o We suggest that you disconnect the appliance from your mains supply when it is not in use Control panel and washer dryer cabinet I MPORTANT Do not use any abrasive cleaner or household polish on either the control panel or operating parts o Wipe over the control panel and the external surface of the machine using a brand new damp cloth with warm water o If you ever spill any liquid detergent or conditioner from the detergent drawer onto the washer dryer cabinet then these should be cleaned up immediately as they could be corrosive Detergent drawer Occasionally the detergent drawer should be cleaned to remove any detergent residue that has built up o Pull the detergent drawer out as far as it will go press down the catch in the middle section of the drawer and then pull the drawer out 25 o Wash the detergent drawer in warm soapy water For ease of cleaning you can remove the upper part of the fabric softener compartment o Detergent can also accumulate inside th
19. e detergent drawer recess so you should also clean this out using a brush o Once you have finished cleaning the detergent drawer and recess you should slide the drawer back into its original position The washer dryer drum The drum of your washer dryer is constructed from stainless steel However if there are objects that can rust placed inside the drum then it is possible for the drum to become stained IMPORTANT Do not use a descaling agent iron steel wool or scouring agents to clean the drum of your appliance o Remove any rust stains on the drum with an appropriate stainless steel cleaning agent Door o You should regularly check to see if any deposits have formed or there are any foreign bodies inside or underneath the rubber door gasket This sits inside the opening of the porthole door 95 maintenance wash Approximately once a month you should complete a 95 maintenance wash this is a wash cycle which you run without clothing placed in the drum but still using detergent This helps prevent the build up of bacteria inside of the drum and the rest of the appliance o Place detergent in the main wash section of the detergent drawer Ideally you should use a power or liquid detergent that contains bleach o Select a 95 cotton wash Press the start pause button 2 the door will lock and after a few seconds you will hear the machine start to fill with water 26 o Atthe end of the wash cycle you shoul
20. ions of the manufacturers should be followed Wash program table Program Fabric type Proper Maximum temp Load Cotton First check if laundry is 60 C Pre wash Normal machine washable white Cold 30 C rinse cotton linen towel and 40 C sheets 95 C Colourfast garments shirts night dresses pyjamas and lightly soiled white cottons underwear 40 C BUM 3kg handwash damaged silk curtains 3kg Intensive Heavy soiled clothes blue 60 C Cold Pre mE Less than jeans climbing clothes ruck 30 C 40 C rinse 3kg sack sports wear 95 C Mound 20 Coloured p which is p soiled 3kg EM wear Lightly soiled fast and thin Cold Cold Pre uM laundry 309C rinse 409C load un mem outside 15 Pre Wash If the laundry is heavily soiled the pre wash option is recommended This option is available for cotton and synthetic wash programs You should place detergent in the pre wash compartment of the detergent drawer as well as in the main wash compartment Rinse Will introduce an additional rinse which will help to remove traces of detergent residue Water This will add an extra 6 litres of water to the rinse section of any cycle to increase the rinse performance without lengthening the cycle time Wash program guidance o A wash program option can only be selected if the program table advises that it is possible with the wash cycle you have selected o
21. ke sure that the washer dryer is installed on a flat and level floor o Ensure that all four feet are resting firmly on the floor by pressing down on each corner and making sure that the appliance is stable If it is unstable then follow the Locating your washer dryer and Levelling the appliance sections Poor spin results o Clean the drain pump see Cleaning the drain pump filter section Water in the detergent drawer o Although there will be some water residue left in the detergent drawer after a wash cycle has completed If the drawer is full of water then you may need to clean the detergent drawer 38 I MPORTANT Your appliance has an unbalance control system If this system detects that the washload is unevenly distributed inside the drum Your washer dryer will try to redistribute the load before spinning If after several attempts it is unable to redistribute the washload then the appliance will either spin at a slower speed or skip the spin cycle and proceed to the drain section of the wash cycle Uneven load distribution can be caused by too large a wash load or too small a wash load It can also occur if a single item if washed inside the appliance IMPORTANT If your appliance appears not to be operating correctly then you should disconnect it from your mains supply and then contact the Customer Care Department on telephone number 0118 933 6911 DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF Please n
22. ned in this booklet please contact the Baumatic Advice Line General Safety o Repairs to your appliance must only be carried out by a Baumatic engineer or one of its authorised service agents Any attempt by an inexperienced person to repair the appliance could result in injury or damage to your washer dryer o If you notice that the mains cable is damaged The appliance must not be used The same applies if you notice that the worktop control panel or base area is damaged As this could allow access to the internal components of the machine o The appliance should be turned off and isolated from the mains supply before either cleaning or maintenance work is attempted o The mains cable must not be used to pull the plug out of the electrical socket o The machine should not be sprayed with water o The glass of the porthole door may become hot during the higher temperature wash programs o The machine should be allowed to cool before carrying out an emergency drain or cleaning the drain filter o Itis possible for small animals to chew either the mains cable or water hoses which could cause an electric shock hazard Installation o The installation instructions contained within this user manual should be followed o It is obligatory for the completed installation to comply with all relevant building regulations and local water authority requirements Before the first use of the appliance we advise that a 95 degree co
23. nstability of the machine when the adjustable legs have been set to the correct level 35 Power supply v IMPORTANT The electrical socket must still be accessible once the appliance is installed v Consult the rating plate located on the inner rim of the porthole door or the right hand side of the cabinet BEFORE making the electrical connections Ensure that the voltage reaching the plug is the same as that on the rating plate v DO NOT REMOVE THE RATING PLATE AS THE INFORMATION ON IT IS IMPORTANT v The moulded plug that is supplied with the appliance must be placed into an earthed and insulated socket Y Broken or damaged power leads must only be replaced by a suitably qualified person A power lead of a similar type must be used in replacement v IMPORTANT We do not recommend that this appliance is connected to an extension lead Before first use maintenance wash o When your washer dryer has been correctly installed we recommend that you perform a maintenance wash cycle without any clothing being placed inside of the drum o This will check that all aspects of the installation are correct it will also remove any deposits that may have been left on the drum by the manufacturing process o Select a 95 C cotton wash o A small quantity of detergent should be used during this maintenance wash 36 Error code failure system If your appliance senses that it is not operating correctly then an error
24. ose Detergent drawer Drain hose Drain pump filter flap Adjustable feet Accessories Control panel Cotton Norma Y NA Quick 20 ri Wash Wah Soak Peia Doon Chid Synthetic Ni B Sports Wear code wc A wE Delicate Hand Wash I Y H Tub Clean Spin f Weeku x mon moon wwo BEE EEE Intensive nn Br Drain iseleng bon Cupbosd Very Time 1 Power button Press this button to turn the power on or off 2 Start pause button Operation and temporary stop is repeated as it is pressed When you want to change a program while it is in use press this button then select the program you want to change to and then press this button 3 Wash program selection knob You can select the wash cycle you want by rotating the Delicate Hand Wash V TubCiean knob to choose from 8 options Lintensive Pain around the outside EB gt N Cotton Normal Quick 20 Synthetic W Sports Wear pl 4 Temperature button This button can be used to ES adjust the temperature of the water according to the type emp of load that needs cleaning As the button is pressed the temperature of the water can be selected through the following options Li Cold gt 30 C 340 C gt 60 C 395 C perm 1 Dry 5 Spin button By pressing this button the spin speed can be chosen You can set
25. ote that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault then you may be liable for the cost of the call out charge The appliance must be accessible for the engineer to perform any necessary repair If your appliance is installed in such a way that an engineer is concerned that damage will be caused to the appliance or your kitchen then he will not complete a repair This includes situations where appliances have been tiled in sealed in with sealant have wooden obstructions placed in front of the appliance like plinths Or any installation other than the one specified by Baumatic Ltd has been completed Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance IMPORTANT Baumatic Ltd operates a policy of continuous improvement and reserves the right to adjust and modify its products without prior notification 39 D Baumatic United Kingdom Baumatic Ltd Baumatic Buildings 6 Bennet Road Reading Berkshire RG2 0QX United Kingdom Sales Telephone 0118 933 6900 Sales Fax 0118 931 0035 Customer Care Telephone 0118 933 6911 Customer Care Fax 0118 986 9124 Spares Telephone 01235 437244 Advice Line Telephone 0118 933 6933 E mail salesObaumatic co uk customercare baumatic co uk spares baumatic co uk technical baumatic co uk Website ww
26. r the level should be below the MAX level o If you want to use bleach then you should put it into the main wash compartment with your detergent e Press and hold the power button 1 the LCD display will show and all the program lights will come on e If you press the start pause button 2 next without selecting a program the cotton normal wash will be selected as the default program e Alternatively you can use the wash program selection knob 3 to select the cotton program e A wash temperature of 40 C with an 800 rpm spin will be selected automatically by the appliance e You can use the temp button 4 to adjust the wash temperature cold 30 C 40 C 60 C and 95 C wash temperatures are available e You can use the spin button 5 to adjust the spin speed e You can use the wash button 6 to select a pre wash or soak to a cycle You can also press the rinse button 11 to include a rinse Press the start pause button 2 the door will lock and after a few seconds you will hear the machine start to fill with water The machine will automatically use the appropriate amount of water by sensing the weight of your laundry 17 Synthetic program O Put the laundry into the drum and then close the door The maximum wash load size is below 3kg for the synthetic program In the detergent drawer put detergent into the main wash and pre wash compartments Put detergent into the pre wash compartment
27. r for the drying cycle to run on automatically from the wash cycle IMPORTANT If you are running on automatically from the wash cycle please note that the maximum size of drying load is 7 kg End of cycle o Atthe end of a wash cycle the door lock light will remain lit for a couple of minutes I MPORTANT You should not attempt to open the porthole door until the door lock light has gone out When the door lock light has gone out and you hear the door lock disengage you can open the porthole door and remove the laundry Pausing a wash program O If you want to pause a wash program temporarily you should press the start pause button 2 When you want to restart the wash cycle press the start pause 2 button again Changing a wash program O O If you want to change a wash program once the wash cycle is already in progress you should first press the start pause button 2 Use the wash program selection knob 3 to change the wash program to the one that you require 23 O IMPORTANT Changing the wash program will cancel any spin or temperature alterations that you have made and any program options that you have selected You will need to make the spin temperature alterations again and re select any program options that you require Delay start feature Your appliance has a delay start feature which allows you to delay the start of a wash cycle until a later time O Put the laundry into the drum
28. r through the porthole door Therefore please check the drum before using the appliance Any packaging that is removed from the machine should be kept away from children All detergents should be kept out of a child s reach and in a safe place Specifications 18 wash programs 5 drying programs 9 kg wash load 7 kg drying load 1400 rpm maximum spin speed O Or ame a O LED display Delay start Digital condensing dry system Digital countdown indicator Wash phase indicator Tilted drum Air bubble washing system 488 mm porthole and 180 door opening Antibacterial surface Failure detection system Imbalance control system Overflow protection Foam protection Adjustable feet Direct drive system Safety door lock O O 20 70 29 OG cuoc X 0 70 00 DO 20 0 Appliance dimensions Height 850 mm Width 600 mm Depth 645 mm Energy ratings Energy efficiency class wash only A Wash performance class A Water extraction performance class A For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice The rating plate for your washer dryer will either be located on the right hand side of the cabinet or behind the porthole door Model Number Serial Number Date of Purchase Description of the appliance Inlet h
29. rain hose so that it cannot move whilst the washer dryer is in use v Place the end of the drain hose on Outlet hose your drain pipe Push it a short way retainer down into your drain pipe v IMPORTANT Do not insert the drain hose too deeply into the water pipe as this may cause siphoning VV TY Fires 4 Tie strap Y Utilise the outlet hose retainer and tie strap to keep the outlet hose in position when the appliance is on a wash cycle aye My 34 v NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH Levelling the appliance v Place the washer dryer on a solid and level floor surface v DO NOT PLACE THE WASHER DRYER ON A CARPET OR A SUSPENDED FLOOR CL If the washer is installed on an L g E unsuitable floor it could make j pm b MC z h neiaa considerable noise vibrate and Two N EOS y cause a malfunction a Pa y MA hi mm P REM m On a slope Uneven floor 2 Adjust the level of the washing machine using the adjustable legs Please check if there is any gap between the four adjustable legs and the floor Turn the adjustable legs using the enclosed spanner adjust the level of the machine and make sure that it is stable Adjust the fixing nuts tightly so that the washer Adjustable maintains the adjustment leg 3 Make sure that the washing machine does not move when you press down the four comers of the washer s top plate I MPORTANT There should be no i
30. ry gt Spin Wash display This lights the wash functions that have been selected such as a pre wash or a soak Wash program temperatures This light indicates which wash temperature has been selected Spin speeds This light indicates whether a spin speed has been selected Child lock This light indicates that the child lock has been switched on Door lock This light indicates that the automatic door lock has been activated as the cycle is in progress Timer display This indicates how long is left of the wash cycle that is in progress Dry display This indicates which drying cycle has been selected 11 Detergent drawer wash Conditioner Pre wash section Main wash section UY This compartment should have detergent placed in it you should also put a water softening agent in this section if you use one The detergent will be added to the drum at the start of the main wash program Conditioner section e This compartment should be used for liquid conditioners fabric softener starch They will be added to the wash load during the final rinse Pre wash section LU This compartment should have detergent placed in it if you are going to select a pre wash before the main wash cycle 12 Preparing the wash cycle Preparing your garments for washing O Your washing should be sorted out according to the fabric type and the wash care symbol that is printed on the garment s wash care label see separate se
31. ted area with white vinegar and then rinse out unl in COLD water Sponge with white spirit Treat stiffened areas with an enzyme pre wash softener normally Rub a little detergent on the stain and then wash normally Grass Sponge with white spirit vt EE meer 20 Grease and Lay the affected area facedown on an absorbent cloth Using stain Wash normally Apply lemon juice and salt and then place in the sun Wash normally Lipstick Sponge with white methylated spirit and wash normally Mildew Wash in WARM water and detergent Moisten area with lemon juice dry in the sun and wash normally If the stain persists and the fabric is suitable use a mild fabric bleach Brush off any dry mud Rinse in COLD water If the stain persists rub in a little detergent and wash normally paint flammable dry cleaning fluid and wash normally bordi aed Po whilst still wet rinse in WARM water and wash paint normally Dampen a cloth with hydrogen peroxide lay it over the affected area and press with a fairly hot iron Poor wash results My garments are looking grey and there are limescale deposits present in the drum of my washer dryer There is not enough detergent being added The incorrect detergent is being used Stains are not being pre treated The correct wash program or wash temperature was not selected Oe 20 020 have followed the advice given above but my garments are still coming out with grey st
32. the spin speed by rpm through the following options Rinse Hold 2 400 2 800 2 1000 2 1400 6 Wash button You can select the cycle you want by using this button The light of the chosen cycle will glow after selection As the button is pressed the wash cycle is chosen through the following options Wash 2 Soak 2 Pre wash 7 Dry button You can select the dry cycle you require by pressing this button You can choose through the following options depending on how dry you want your items to be Low temp 2 Iron gt Cupboard gt Very gt Time 8 Water button You can press this button to add an extra 6 litres of water to the rinse section of any wash cycle to increase the rinse performance without lengthening time it takes to complete 9 Delay start button This button can be used to delay the start of the wash cycle from between 1 12 hours 10 Memory button You can use this button to recall a cycle that you have previously programmed the washer dryer to remember 11 Rinse button You can press this button to introduce an additional rinse which will help to remove traces of detergent residue 10 LED display Soak Pre Wash Door amp Child amp ce we oe n BBB 400 800 1000 1400 ENP LIE Y EA ET Iron Cupboard Very Time Wash cycle progress indicator This lights when a wash cycle is in progress to indicate what stage of the wash cycle the appliance has reached from Wash 2 Rinse 2 D
33. to change the washing temperature 4 the spin speed 5 or add wash options pre wash or soak 6 or a rinse 11 then press each button accordingly Press the start pause button 2 The door will lock and the machine will supply wash water depending on the weight of the laundry The appliance will then begin washing Quick 20 program O Put the laundry into the drum and then close the door The maximum wash load size is below 3 kg for the Quick 20 wash program In the detergent drawer put detergent into the main wash compartment Softener should be poured into the middle compartment of the detergent drawer the level should be below the MAX level If you want to use bleach then you should put it into the main wash compartment with your detergent Press the power button 1 the LCD display will show and all the program lights will come on 20 Use the wash program selection knob 3 to select the Quick 20 program A wash temperature of cold with an 800 rpm spin will be selected automatically by the appliance Press the start pause button 2 the door will lock and after a few seconds you will hear the machine start to fill with water Sports wear program O Put the laundry into the drum Put detergent and softener into the detergent drawer Softener should be below MAX level Then close the door Put detergent into the pre wash compartment only if you want to add pre wash When you
34. tton wash is completed No garments should be placed inside the machine however a small amount of detergent must be used During Use It is recommended that the appliance is unplugged and the water supply is turned off after the machine is used This appliance is only designed to wash normal domestic washloads If you use your washer dryer in any other way or it is incorrectly used then Baumatic accepts no liability for any damage that might be caused and any guarantee will be void No attempt should be made to alter or modify the specifications of this appliance The detergents that you place in this appliance should be suitable for automatic washer dryers With regards to dosage levels the detergent manufacturer s recommendations should be followed You should not wash garments that have been in contact with flammable materials Your washer dryer should not be used for dry cleaning If you use either dyes or bleaching agents inside this machine then you should consult with the manufacturer of these products to make sure they are suitable for use in your washer dryer Baumatic cannot be held responsible for any damage that may result Child Safety O O O Your washer dryer should only be used by adults You should not allow children in the area of the machine unsupervised You should not let them touch the controls or play with the appliance It could be possible for a child or pet to gain access to the washer drye
35. w baumatic co uk Republic of Ireland Service Telephone 1 890 812 724 Spares Telephone 091 756 771 Czech Republic Baumatic CR spol s r o Pr myslov z na Sever 696 460 11 Liberec 11 Czech Republic 420 483 577 200 www baumatic cz Slovakia Baumatic Slovakia s r o Galv niho 7 D Slovakia 421 255 640 618 Germany Baumatic Gmbh Lilienthalstrasse 1 320 52 Herford Deutschland 49 5221 694 99 0 www baumatic de Italy Baumatic Italia S R L Via Galvani N 3 35011 Campodarsego PD 3904 9920 2297 www baumatic it Holland Baumatic Benelux B V Grindzuigerstraat 22 1333 MS ALMERE Nederland 3136 549 1555 www baumatic nl 40 42 43 44
36. want to use bleach put it into the main wash compartment with detergent Press the power button 1 and the LED will show only and all program lights will turn on Select the sports wear program using the program selection dial 3 The washing temperature will be automatically set at cold with a spin speed of 800 rpm You can alter the temperature of the water by pressing the temperature button 4 Only cold 30 C and 40 C are selectable Press the start pause button 2 and the door will lock The wash water supplied will be influenced by the weight of the laundry The appliance will then begin washing Spin only O Put the laundry into the drum and then close the door Press the power button 1 the LCD display will show and all the program lights will come on Select the spin speed 5 that you require by pressing the spin button The water temperature is set to cold automatically 21 Press the start pause button 2 the door will lock and after a few seconds you will hear the machine start to spin Only wash O Drain Put the laundry into the drum and put detergent and softener into the detergent drawer Then close the door Press the power button 1 and the LED will show only Select the wash course you want by pressing the wash button 6 The temperature will automatically be set to cold Press the start pause button 2 and the washer
Download Pdf Manuals
Related Search