Manual - FAST.Eu
Contents
1. Connecting the drain hose You must connect the drain hose at a height from 50 cm minimum to 110 cm maximum from the bottom part of the appliance Secure the drain hose using a clamp The loose end must not be submerged in water Built in This dishwasher is designed to be built in Adhere to all warnings and instructions contained in this user s manual during installation Before installation check that the required dimensions of the dishwasher to be built in correspond to the dimensions of the installation location see illustration below 815 870 EN 9 Copyright 2012 Fast CR a s Revision 10 2012 After connecting the inlet and drain hoses slide the dishwasher into the installation area Take care not to damage crimp bend or otherwise impair any of the hoses WARNING Only remove the top cover if it is absolutely necessary for the installation into the built in area The dimensions of some built in areas may be higher and so the dishwasher will fit in with the top cover attached Turning on the dishwasher Before turning on the dishwasher check the recommendation below The dishwasher is levelled and properly seated Is the inlet valve opened Joints do not leak in the connection points Cables are properly connected Is the power source turned on The water supply hose and the drain hose are not knotted up You have removed all packaging material and all printed materials EN 10 C2. designed to be used with automatic dishwashers Never use soap washing or cleaning detergents designed for hand washing Keep all these substances out of the reach of children Store all cleaning agents in a safe place Keep children away from all washing and rinsing agents and at a sufficient distance from the open dishwasher door because there could be remains of detergents inside Do not use any solvents in the dishwasher The could cause an explosion Dishwasher detergents are very alkaline and their ingestion may be life threatening Avoid contact with the skin or eyes because there is a danger of chemical burns of eyes or skin Keep children at a sufficient distance from the dishwasher when the door is open Follow the safety instructions of the dishwasher detergent manufacturer The water inside the dishwasher is not intended for drinking It may contain remains of detergents Place sharp items in such a way that they do not damage the door seal WARNING Knives and other utensils with sharp tines and blades must be placed inside the basket with tips facing downwards or in a horizontal position Ensure that the dishwasher door is always closed except for the time when dishes are being inserted or removed This will prevent the danger of tripping over the door and subsequent injury If the door is open do not allow children to come close to the dishwasher EN 3 Copyright 2012 Fast R a s Revision 10 2012 WARNIN
3. There is a danger of suffocation e The electrical and plumbing installation necessary for the connection of this dishwasher may only be performed by a person with relevant qualifications Maximum permitted water pressure is 1 Mpa Minimum permitted water pressure is 0 03 Mpa Connect the appliance to the water source using a new hose do not use a used hose The power cord must not be excessively or dangerously bent or pressed during the installation For safety reasons changing the technical parameters or making any other modifications to the appliance is dangerous e Never use the dishwasher if the electrical connection or the water hose are damaged or if the control panel workbench or its support is damaged when the inside of the appliance is freely accessible Contact a local service centre to avoid exposing yourself to possible dangers e You must not drill into any side of the dishwasher so that you do not damage the plumbing and electrical components e Do not turn on your dishwasher until all covers are properly installed WARNING When using the dishwasher follow all the notices below EN 2 Copyright 2012 Fast CR a s Revision 10 2012 5 Grounding instructions This appliance must be grounded In the event of a failure or malfunction the grounding will reduce the risk of injury by electrical shock by ensuring a lower resistance to the electrical current This appliance is equipped with a power cord with a grou
4. and other important part of the dishwasher This is not covered by the warranty Only refill the salt compartment when the salt warning indicator light on the control panel lights up Depending on how well the salt dissolves the warning indicator light may stay on even after the salt compartment has been refilled If there is no salt warning indicator light on the control panel on some models you can estimate the amount after adding salt to the system by the number of cycles performed by the dishwasher If salt runs out anywhere remove it by starting the rinse program or the quick wash program Adding rinsing aid Rinsing aid compartment e The rinsing aid is released during the last rinse so that water drops do not remain on your dishes causing Stains It also improves drying due to the fact that all the water flows off the dishes Your dishwasher is designed to only be used with a liquid rinsing aid The rinsing aid compartment is located on the inside wall of the door next to the dishwashing detergent compartment e Fill up the compartment by opening it and pouring in the rinsing aid until the indicator goes completely dark The capacity of the rinsing aid compartment is approximately 110 ml NOTE Use only branded dishwasher rinsing aids Never pour other mixtures such as liquid detergents etc into the rinsing aid compartment Otherwise the dishwasher may be damaged When should the rinsing aid be refilled Ifthe rins
5. their chemical additives are essential for the removal of soils their decomposition and removal from the dishwasher For this purpose the majority of commercial quality dishwashing detergents are suitable Dishwashing detergents There are 3 types of dishwashing detergents 1 containing phosphates and chlorine 2 containing phosphates and without chlorine 3 without phosphates and without chlorine New dishwashing detergents usually do not contain phosphates and so the softening function of the phosphates is missing In such a case we recommended the use of a softening salt even when the water hardness is a mere 6 dH If you use dishwashing detergents without phosphates and have hard water this leads to the frequent appearance of white stains on dishes and glasses In such a case you will therefore achieve better results if you add more dishwashing detergent Chlorine free dishwashing detergents whiten only slightly For this reason strong and colourful stains will not be completely removed In such a case select a program with a higher temperature EN 15 Copyright 2012 Fast CR a s Revision 10 2012 Concentrated dishwashing detergents Based on their chemical composition dishwashing detergents are divided into two basic types e standard alkaline dishwashing detergents with caustic additives e less alkaline dishwashing detergents with natural enzymes Using standard washing programs in combination with concentrated dish
6. water supply company If you use hard water in your dishwasher scale deposits will be left on your dishes which may negatively affect the washing efficiency and lifetime of your dishwasher The appliance should be equipped with a special softener which uses the salt compartment for salt specifically designed for eliminating scale and minerals from water Identifying water hardness The dish washing efficiency of your dishwasher depends on the hardness of the water used Therefore your dishwasher is equipped with a system which reduces water hardness at the main water inlet The better the system is set up the better the achieved washing efficiency Your water supplier should provide you with information about water hardness in your area or you may measure it yourself using a simple harness test a special testing strip not included Take the Allowyour Leavethe Take it out of Wait Compare the hardness value on the testing tap water testing strip thewaterand approxi strip to the hardness table supplied strip out toflow over dippedin tap it mately with the testing strip of the the strip for the water 1 minute packaging approxi for approxi for the mately mately result 1 minute 1 second i Levell OILILL No Lime second l i Level2 OILILL Very low lime content Level3 TTT TTT WM WM Low lime content Level4 TTT TM MN WM Medium lime content Ee Level 5 TTM MN MN MW Limecontent Level6 MCM MN MM High l
7. DISHWASHER USER S MANUAL ttn at nnee rent eenen PD 1251 BiT Dear customer Thank you for buying a PHILCO brand product So that your appliance serves you well please read all the instructions in this user s manual CONTENTS PART 1 BEFORE PUTTING INTO OPERATION sssenorsenessersndenerdennendenenssnnendense pee seendennerdinnendenbsnnesndsnsenetnediee 2 e Important safety INS RUCUONS i2 ssssevnvevovessivicevvissvonniessysanoeriessboauehstnssnecaivenvevnceianssdansepvuavnoneoenios dnnsnuststedennnenmonndvontvaasnvansses aonvion ste 2 PART 2 DESCRIPTION OF THE PRODUCT ccsssacvcesvescesatencssccacsscosebecsvesseosssaccnasasndasnankosacsnssucnsassersastereesucsseveesc ne 5 PART 3 INSTALLATION ccsccscssssisciscssssssscsccsssscsesccsasssssnsussssnssesssacscosesnscascscsnesssssasessssvestsscsecssussceasssensssssssossvesececeus 6 A cece sete ex aires sen sues AE T A 6 e PIM eee denon 6 EE ede Koln ng 7 a OWO ar TE EA EA 7 a Connecting munnke lg Ag 8 LN 9 PART 4 CONTROL PANEL issssssisssscscsassicsaccdscesoiesscdacusnedsssosdnsnsacceccsecwsscdes ssaduenssacescsessnssdceavedvsnecasesisasssseacoevesseess 11 5102 oe ant Sententia etienne vaten bednet teton 12 Iro TENEN 12 EN 13 ACE ES MAO AMON eedt eetbare debatten dende 14 e Function of the detergent s sxsssxassnsivavinvesstannsnevsnstessovacsvssanacaavnpsaiaden noot bidon hteravan kaastaart mondesdankenarentesdandskdens 15 e Dosage of the CETEKGOMTs cissssnneieiovsosncasneosicin
8. G Do not sit on the door or on the wire racks do not stand on them or handle them with brute force Do not touch the heating elements during operation or immediately afterwards These instructions are intended only for dishwashers with freely accessible heating elements Do not place any heavy items on the door when it is open and do not stand on it The appliance could tip over Open the dishwasher carefully during operation so that water does not spray out and so that you do not get scalded by the escaping steam Do not pull any dishes out of the dishwasher until the cycle is completed After the completion of a washing cycle check that the detergent compartment is empty After using the dishwasher disconnect it from the power source and turn off the water supply Under no circumstances tamper with the control buttons Servicing disposal If it is necessary to repair the appliance contact an authorised service technician who should use only original spare parts If the power cord is damaged it must be replaced by the manufacturer or the manufacturer s service technician to prevent injury to persons or damage to the appliance Never attempt to repair the appliance yourself Repairs carried out by inexperienced persons may lead to injuries or serious damage to the appliance Contact a local service centre Always request original spare parts When taking an old dishwasher out of service or when disposing it remove the dishwas
9. ainer Always use salt designed for dishwashers The salt compartment is located under the lower rack and you should refill it in the following manner NOTE e Use only salt specifically designed for use in dishwashers Any other kind of salt which is not specifically designed for use in dishwashers particularly table salt would damage the softener system in the dishwasher Damage caused by the use of inappropriate salt is not covered by the manufacturer s guarantee and the manufacturer takes no responsibility for any damages caused Add the salt before starting one of the full washing cycle programs This will prevent salt crystals or salt water from lying at the bottom of the dishwasher where this could lead to corrosion EN 13 Copyright 2012 Fast CR a s Revision 10 2012 a Slide out the lower rack and then unscrew the lid of the salt compartment see pic 1 2 b Before the first wash pour 3 4 litre of water into the salt compartment c Place the funnel included accessory on the opening of the compartment and pour 2 kg of salt into it e It is normal for a smaller amount of water to run out of the compartment d After filling the compartment screw the lid back on by turning it in the clockwise direction e You should start a washing program immediately after the salt compartment has been refilled we recommended the rinse or quick wash program Otherwise the salt water could damage the filtration system pump
10. angerous to open the dishwasher door during a wash because you could be scalded by hot water EN 24 Copyright 2012 Fast CR a s Revision 10 2012 After the end of the washing cycle 1 After ending the washing cycle the end the program indicator light End will turn on Press the ON OFF button to turn off the dishwasher 2 Disconnect the power cord from the power socket and shut off the water inlet NOTE Wait a few minutes before taking dishes out of the dishwasher so that you do not handle the dishes while they are hot and more susceptible to breakage and they will dry better too NOTE If you open the door during the washing cycle or an electrical power outage occurs the washing cycle will be interrupted and it will resume after the door is closed or the electrical power supply is renewed EN 25 Copyright 2012 Fast CR a s Revision 10 2012 PART 6 MAINTENANCE AND CLEANING Filtration system The filter prevents food remains or other foreign items from entering the pump Food remains may clog the filter and in such a case it is necessary to take it out The filtration system consists of a coarse filter a plastic filter and a micro filter fine filter 1 Plastic filter Food remains and soils caught by this filter are pulverised by a special jet on the bottom spraying arm and flushed down the drain 2 Coarse filter Larger parts e g bits of bone or glass which could clog the drain are stop
11. as soon as the washing program finishes the end of program indicator light will be lit At the same time a sound will be made 5 times NOTE The washing program that was set previously will remain in the dishwasher s memory Before turning on the dishwasher again check that you have selected the correct washing program Child lock function To prevent buttons from being pressed accidentally it is possible to activate the child lock function Hold down the Start Pause and delayed start buttons at the same time for 4 seconds The 3 h indicator light will flash once To cancel the child lock function hold down the Start Pause and delayed start buttons at the same time for 4 seconds The 3 h indicator light will flash twice EN 11 Copyright 2012 Fast R a s Revision 10 2012 Before first use Before you put your dishwasher into operation a set water softening pour 3 4 litre of water into the salt compartment and fill it up with salt fill the rinsing aid compartment fill the dishwashing detergent compartment an Water softener The water softener is made so that it releases minerals and salts contained in water which would have a negative effect on the operation of the dishwasher The higher the content of these minerals and salts the harder the water is You should set the water softener according to the water hardness in your area Information about water hardness in your area should be provided by your
12. at the new owner can find out about the operation of the appliance and the relevant warnings e Before installation or operation of the appliance you MUST carefully read all the safety instructions and the user s manual e Before putting the appliance into operation for the first time check that it has not been damaged during transport e If the appliance is supplied in the winter months when the temperature falls under 0 C store the appliance at room temperature for 24 hours before first use e This dishwasher is designed for washing household dishwasher safe dishes Use the dishwasher only for the purposes for which it was designed The dishwasher is designed for a maximum of 12 sets of dishes e This appliance must not be used by any persons including children with mental disabilities weak strength or by inexperienced persons unless they have been properly trained or schooled in the safe use of the product or unless they are properly supervised by a qualified person who is responsible for their safety e Children must be supervised to ensure that they do not play with the appliance Installation e Check that the dishwasher has not been damaged during transport Never connect a damaged appliance If the dishwasher is damaged contact the supplier e It is necessary to remove all packaging from the dishwasher before it is used Dispose of the packaging materials in a proper manner Do not allow children to play with the packaging material
13. cuit oner owen Check that the dishwasher is turned on and the door is shut The properly Check that the power plug is correctly connected turned on dishwasher to the power socket will not Check that the water supply is correctly connected and start Water pressure is low Np whether it is open The dishwasher door is Check that the door is closed properly and secured with not closed properly the latch IRS 8 NOTONTE Check the drain hose The drain hose dishwasher The filteriecdoaded Check the coarse filter is not ggea see section Cleaning the filters draining i eT Check the kitchen sink and ensure that it drains well If the water The kitchen sink is ni doned problem is an incorrectly draining sink first call a plumber ggen and only then the service technician Technical problems Use only special detergents for dishwashers to prevent the formation of suds If this occurs open the dishwasher and allow the suds to evaporate Pour 0 4 of cold water into the dishwasher Close the dishwasher to the latch and then start the rinse cycle to drain the water Repeat if necessary Always immediately clean the rinsing aid Use a dishwashing detergent not containing dyes An incorrect There are dishwashing detergent suds in the was used dishwasher The rinsing aid has spilled out You have used a dishwashing detergent with dyes There are stains i
14. e frequency V Hz 220 240 V 50 Hz EN 34 Copyright 2012 Fast R a s Revision 10 2012 INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS Dispose of packaging material at a public waste disposal site DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES The meaning of the symbol on the product its accessory or packaging indicates that this product shall not be treated as household waste Please dispose of this product at your applicable collection point for the recycling of electrical amp electronic equipment waste Alternatively in some states of the European Union or other European states you may return your products to your local retailer when buying an equivalent new product The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health which could be caused as a result of improper liquidation of waste Please ask your local authorities or the nearest waste collection centre for further details The improper disposal of this type of waste may fall subject to national regulations for fines For business entities in the European Union If you wish to dispose of an electrical or electronic device request the necessary information from your seller or supplier Disposal in other countries outside the European Union If you wish to dispose of this product request the necessa
15. e only branded dishwashing detergents designed for dishwashers WARNING The dishwashing detergent is corrosive Keep it out of children s reach Using the dishwashing detergent Use only dishwashing detergent specifically designed for use in dishwashers Store the dishwashing detergent in a dark and dry place Do not put dishwashing detergent powder into the compartment unless you intend to start the dishwasher EN 16 Copyright 2012 Fast CR a s Revision 10 2012 Dosage of the dishwashing detergent 1 Release the clip to open the dishwashing detergent compartment 2 Place the required amount of dishwashing detergent into the main wash detergent compartment if you are using a dishwashing powder Make sure that the amount of the dishwashing detergent is between the MIN and MAX level lines 3 Ifthe dishes are overly soiled also add dishwashing detergent into the pre wash partition Close the dishwashing detergent compartment 5 Now turn on the dishwasher gt A NOTE The mark MIN in the main wash detergent compartment corresponds to approximately 20g of dishwashing detergent The pre wash detergent compartment will take approximately 5g of dishwashing detergent Follow the recommended dosages and storage indicated by the manufacturer on the packaging of the dishwashing detergent Close the lid and press it down until it clicks in If the dishes are heavily soiled also add dishwashing detergent into
16. her door This will prevent children or animals from closing themselves inside the dishwasher and prevent this life threatening situation EN 4 Copyright 2012 Fast CR a s Revision 10 2012 PART 2 PRODUCT DESCRIPTION Upper rack with cup shelves Top spraying arm Lower rack Bottom spraying arm Filters Rating label Control panel Washing detergent and rinsing aid compartment Basket for cutlery 10 Salt compartment located in the bottom part of the appliance 11 Rail of the upper rack 12 Active drying system for better dish drying results in the dishwasher Sey Be WN a EN 5 Copyright 2012 Fast CR a s Revision 10 2012 PART 3 INSTALLATION Unpacking Remove the external packaging remove the protective plastic film from the surface of the appliance if used and clean the external parts of the appliance with an agent designed for this purpose Do not use steel wool or any coarse agents which could irreparably damage the surface of the appliance Carefully remove all papers and adhesive tape from the appliance doors and other parts packed in polystyrene Remove documents and accessories from inside the appliance The packaging material is recyclable and is marked with a recycling symbol For disposal follow the local regulations Packaging materials plastic bags polystyrene parts etc must be kept out of the reach of children because they present a possible source of danger Ca
17. ight 2012 Fast CR a s Revision 10 2012 How to disconnect the water supply hose e Shut off the water inlet e Reduce water pressure by pressing the reduce pressure button This will reduce the water pressure and prevent water from possibly squirting out into the room e Unscrew the water supply hose from the water tap WARNING To prevent water from staying in the hose close the water inlet into the dishwasher This does not apply to dishwashers with the aqua stop function Connecting the drain hose Insert the drain hose into the waste water pipe with a minimum diameter of 4 cm or leave it lying in the sink and ensure that it is not bent or dented Use a special plastic bracket supplied with the appliance The hose must be at a height of 50 to 110 cm above the ground The loose end of the hose must not be submerged in water so that reverse water flow does not occur max 110cm NOTE The hose must be at a height of 50 to 110 cm above the ground The loose end must not be submerged in water EN 8 Copyright 2012 Fast CR a s Revision 10 2012 Draining water e Connect the drain hose The drain hose must be properly attached so that water does not leak Check that the hose is not knotted up or pinched Extending the hose e If you need to extend the drain hose you must use the same type of drain hose e The hose must not be longer than 4 meters Otherwise the efficiency of the dishwasher would be reduced
18. ilure Shut off the water inlet Contact an authorised service centre It is not possible to pump residual water out of the dishwasher The drain hose is clogged The filters may be clogged Turn off the dishwasher and turn on the cancel wash programs If the problem persists contact an authorised service centre Heat malfunction Contact an authorised service centre The warning indicator light is activated when the dishwasher overflows Faulty electronic card Turn off the dishwasher and close the water inlet Contact an authorised service centre Contact an authorised service centre Overheating malfunction the temperature of the dishwasher is too high Heat sensor error Contact an authorised service centre Contact an authorised service centre WARNING e Inthe event that the dishwasher becomes flooded close the water supply before calling the service technician e Ifas a result of flooding or a water leak there is water in the bottom container pour it out before turning on the dishwasher again EN 33 Copyright 2012 Fast CR a s Revision 10 2012 PART 8 TECHNICAL SPECIFICATIONS Water pressure MPa 0 03 1 0 MPa Hot water supply connection max 70 C Total power input W 2200 W NOTE All the here mentioned data is subject to change Operating voltag
19. ime content EN 12 Copyright 2012 Fast CR a s Revision 10 2012 Setting salt consumption The dishwasher is designed to enable the adjustment of salt consumption on the basis of the hardness of the water used This should optimise and adapt the level of salt consumption Water hardness setting indicator ejojolo ojejolo Table for setting up water hardness dF dE French English unit unit 0 9 0 6 Indicator lights P1 and P5 are lit 10 20 7 14 Indicator lights P2 and P5 are lit 12 17 21 30 15 21 Indicator lights P3 and P5 are lit O O 31 40 22 28 Indicator lights P4 and P5 are lit jololole 41 55 29 39 Indicator lights P1 P4andP5arelit O O 6 32 50 56 90 40 63 Indicator lights P2 P4andP5arelit O O 1 Press and hold down the program selection button 2 In this time press the power button 3 Hold down the program selection button until the indicator lights P1 P2 P3 P4 P5 start flashing Then release the button 4 Use the program selection button to set the water hardness level 5 Toconfirm and save into the dishwasher s memory press the power button O O NOTE Your water supplier will provide you with information about the hardness of your water CAUTION If your dishwasher does not have a water softening system you can skip this chapter Adding salt into the salt cont
20. ing aid compartment is empty the relevant indicator light on the control panel will turn on indicating the need to add rinsing aid After filling the compartment with rinsing aid the entire indicator is dark As the rinsing aid is gradually used up the point of the indicator becomes smaller Never allow the amount of rinsing aid to fall below 1 4 of the compartment volume EN 14 Copyright 2012 Fast CR a s Revision 10 2012 CAUTION Wipe any spilled rinsing aid with a wiping cloth so that excessive suds are not formed in the following wash Do not forget to put the lid back on before closing the dishwasher door Setting dial rinse The rinsing aid compartment has six different settings Its factory level setting is 3 If stains form on the dishes or if there is a problem with drying the dishes increase the released amount of the rinsing aid by removing the lid and turning the dial to 4 If despite this step the dishes are not without stains after drying adjust the setting again to a higher level until the dishes are clean after drying If rinsing aid residues remain on the dishes reduce the level to 1 2 The recommended setting is 3 The value set by the manufacturer is 3 NOTE If there are water drops or scale stains on the dishes after the wash increase the dosage If there are white stains or blueish layers on glasses or knife blades lower the dosage Function of the detergent Dishwashing detergents with
21. is 220 240 V 50 Hz power socket specification 12 A 250 V Check that the water inlet is fully open Press the ON OFF button Use the program selection button to select the desired program If necessary select an additional function Close the door to automatically start the program The indicator light of the selected program will turn off when the program is started WN N O uUi D Monitoring the program You can monitor the progress of the washing cycle by watching the indicator lights on the control panel turn on and off NOTE Do not open the dishwasher until the end of washing cycle indicator light turns on During the drying process the dishwasher will not make any sound for 40 50 minutes This is a normal event Changing a program A Changing a program that is already running 1 Carefully open the door Wait until the spraying arms stop Allow excess steam to escape 2 Select a new program 3 Close the door and the new program will start B Cancelling a program 1 Carefully open the door Wait until the spraying arms stop Allow excess steam to escape 2 Press and hold the program selection button for approximately 3 seconds The end of program indicator light will start flashing and the program indicator light will turn off 3 Close the door and the dishwasher will automatically drain the water approximately 30 seconds after the door is closed After this a sound will be made 5 times WARNING Itis d
22. kitchen paper towels because they could scratch or leave marks on the stainless steel parts of the dishwasher Protection against frost In winter take steps against the dishwasher freezing After every wash do the following e Disconnect the dishwasher from the power source Close the water inlet and disconnect the supply hose from the water valve Drain water from the water supply hose and the water valve Drain the water into a container Reconnect the water supply hose to the water valve Take out the filter on the bottom of the dishwasher and using a sponge suck up the water from the waste tank NOTE If your dishwasher is not working because it has frozen contact an authorised service technician EN 28 Copyright 2012 Fast CR a s Revision 10 2012 Cleaning the spraying arms It is important to regularly clean the spraying arms so that hard water minerals do not clog the jets and the bearings of the spraying arms Detach the spraying arms by turning the nut clockwise remove the washer from the spraying arm and then the spraying arm itself Wash the spraying arms in warm soapy water and clean out the jets using a brush After thoroughly flushing them reattach them How to keep your dishwasher in good condition e After every wash After every wash close the water inlet into the dishwasher and leave the door slightly open so that humidity that would otherwise accumulate inside is ventilated out e Disconnec
23. les Wash 40 C Hot rinse IL Pre wash and removal of soils from dishes Pre wash UI Electricity consumption kW h Water consumption I mm Ui vEt NOTE It is necessary to refill the rinsing aid into the compartment Copyright 2012 Fast C R a s EN 23 Revision 10 2012 WARNING Short programs do not include the drying function The above mentioned values were obtained on the basis of laboratory tests according to relevant standards These values may change depending on conditions such as the type of dishes used degree of dirtiness type of dishwashing detergent water pressure water hardness etc NOTE The above provided values are only for your orientation They have been determined on the basis of laboratory tests in accordance with respective standards The values may differ depending on the conditions under which the appliance is used and other factors such as pressure water pressure water temperature ambient temperature etc Turning on the appliance starting a washing program 1 Pull out the lower and upper rack load it with dishes and then slide back in We recommend that you first load the lower rack and only then the upper rack see Load the dishwasher racks Fill the compartment with dishwashing detergent see section Dosage of the dishwashing detergent Connect the power plug to the power socket Power source
24. n a vertical position are dangerous Long and or sharp cutlery e g kitchen knives must be placed horizontally in the upper rack Do not overfill your dishwasher For better washing results and lower power consumption Taking dishes out of the dishwasher To prevent water dripping down from the upper rack on to the dishes in the lower rack we recommended you first empty the lower rack and only then the upper rack Filling the upper rack The upper rack is designed for lighter dishes e glasses cups and mugs and saucers also small plates small bowls and shallow pots if they are not too soiled Place the dishes in such a way that they will not be moved by the sprayed water current Loading the lower rack We recommend you place larger cookware and hard to clean cookware into the lower rack e pots pans lids serving plates and bowls It is better to place serving plates and lids on the sides of the rack so that the spraying arm does not become blocked EN 19 Copyright 2012 Fast CR a s Revision 10 2012 Remember that e pots serving bowls etc must be place bottom up e deep pots should be placed at an angle so that water can freely run out of them e the tines on the lower rack can be folded so that you can insert larger pots and pans or more smaller items Special cookware e g large pans or plates should be placed in the lower rack The recommended placement is shown below Incorrec
25. nding conductor and power plug You must connect the power plug into an appropriate power socket installed and grounded in accordance with local laws and regulations WARNING e The incorrect connection of the grounding conductor may create a risk of injury by electrical shock If you have any doubts about the proper grounding of the appliance ask a qualified electrician or service technician for verification Do not modify the power plug included with the appliance if it does not fit into the power socket Ask a qualified electrician to install a proper power socket Correct use Before inserting dishes or kitchen utensils check that they are suitable for washing in a dishwasher The manufacturer of the dishes or kitchen utensils will provide more details or such information is included in the attached documentation Not adhering to this notice may lead to the damage of dishes or kitchen utensils or also the appliance The warranty does not cover this kind of damage Do not wash plastic items in the dishwasher unless they are marked by the manufacturer as dishwasher safe For plastic items without such markings follow the recommendations of the manufacturer When using the dishwasher you should prevent the plastic items from coming into contact with the heating element These instructions are intended only for dishwashers with freely accessible heating elements Use only agents detergents and rinsing aids salt and polishing agents
26. not are not satisfac dry tory The dishes were incorrectly loaded You did not add enough rinsing aid You took the dishes out too soon Load the dishwasher with dishes according to the instructions Increase the amount of rinsing aid fill up the rinsing aid compartment Do not take the dishes out of the dishwasher immediately after the wash Slightly open the door so that steam is released Only take the dishes out when they are warm and you can hold them in your hand First unload the lower rack This will prevent wetting the dishes with water dripping from the upper rack You selected an incorrect program Knives do not have a quality surface treatment During a short program the water temperature is lower This also reduces the washing efficiency Select a longer program Water drainage is a somewhat more difficult from these items These types of knives or dishes are not suitable for dishwashers EN 32 Copyright 2012 Fast CR a s Revision 10 2012 Error codes Error code Possible causes P3 nk P5 Insufficient water supply Check that the water inlet is fully open and that the water supply was not interrupted Shut off the water inlet Unscrew the water supply hose and clean out the filter on the end of the hose Restart the dishwasher contact an authorised service centre Water supply fa
27. nside the dishwasher General problems There is a white film inside the dishwasher Clean out the inside of the dishwasher using a damp sponge with detergent Use rubber gloves To prevent the risk of the formation of suds never use any other detergents than those designed for use with dishwashers The white film is caused by hard water minerals The affected items are not resistant to corrosion After refilling the salt you did not start any program Salt particles got into the washing cycle Loose water softener lid Check the lid Check that it is pulled tight On the cutlery there are rust stains After adding salt always run a quick wash without dishes and without the Turbo function activated if available EN 30 Copyright 2012 Fast R a s Revision 10 2012 Noise Problem Banging noise is coming from the dishwasher The dishwasher coming from the dishwasher What to do The spraying arm is hitting some dishes located in a rack Interrupt the program and rearrange the dishes so that they no longer interfere Dishes are placed loosely in the dishwasher Interrupt the program and rearrange the dishes Knocking noise coming from the hoses This may be caused by the installa tion or diameter of the hoses This has no affect on the operation of the dishwasher If in doubt contact an authorised ser
28. opyright 2012 Fast CR a s Revision 10 2012 PART 4 CONTROL PANEL Control panel salt tinse aid program delay timer 9h end 1 Power button ON OFF Turning on off power to the appliance After turning on the Start Pause indicator light will come on 2 Program selection button press the button to select the desired program 3 Delayed start button the washing program can be postponed by 3 6 and 9 hours Repeatedly press the delayed start button Delay to select the length of the delay until the dishwasher is started To activate the function press the Start Pause button If you wish to change the set time press the Start Pause button and then set a new value for the delayed start Reconfirm using the Start Pause button If you press the delayed start button when the time is set to 12 hours the delayed start indicator light will turn off If at this time you press the Start Pause button the program will start You can check the set delayed start value by looking at the control lights For example if you set 9 hours the indicator lights 6 h 3 h will gradually light up 4 Salt warning indicator light It will light up if salt needs to be refilled Rinsing aid warning indicator light It will light up if rinsing aid needs to be refilled The warning indicator lights will turn off during the washing cycle or when using 3 in 1 tablets even if the amount is insufficient End of program indicator light
29. ounded replace the socket rather than using adapters etc which could lead to overheating or burning WARNING The incorrect connection of the grounding conductor may create a risk of injury by electrical shock If you have any doubts about the proper grounding of the appliance ask a qualified electrician or service technician for verification Do not modify the power plug supplied with the appliance If the power plug does not correctly fit into your power socket ask a qualified electrician to replace it Water supply How to connect the water supply hose You must connect the dishwasher to a water supply using a new hose Do not use perished old or otherwise damaged hoses Water pressure must be in the range 0 03 MPa to 1 MPa If the water pressure in your system is lower ask for advice from our service department e Pull out the hose fully from the storage area in the rear part of the dishwasher e Screw in the water supply hose to a tap with a 3 4 thread e Fully open the water supply before turning on the dishwasher Water supply hose The water supply hose has double wall The water filling system guarantees intervention by blocking the water supply in the event that the water supply hose fails WARNING The hose connected to the water supply to the sink may break if the sink is connected to the same water system as the dishwasher We recommend that you disconnect the hose and seal the opening EN 7 Copyr
30. ped by the coarse filter Remove the soils caught by this filter by taking the filter out gently press the plug on the top of this filter and lift it up 3 Fine filter This filter stops the remains of soils and food in the area of the water tank and prevent the remains from returning back to the area of the dishwasher during the wash Installing the filter The filter effectively removes food remains from the water used to wash the dishes and so this water can be used repeatedly during the wash You will achieve better wash results if you regularly clean out the filter For this reason it is better to remove the food remains from the filter after every wash by flushing out the semi circular filter and containers under running water Take out the filter by pulling upwards on the container handle WARNING e Never use the dishwasher without a filter e An incorrectly seated filter may lower the efficiency of the dishwasher and cause damage to dishes EN 26 Copyright 2012 Fast CR a s Revision 10 2012 1 To remove and clean the filtration system turn the filter anticlockwise and then lift it up 2 Pull out the metal plastic filter 3 Take the course filter out of the fine filter NOTE Follow all the steps of this procedure remove the filtration system then reinstall it by proceeding from step 3 tostep 1 Recommendation e After every use of the dishwasher check that the filters are not clogged e You can take o
31. refully inspect the appliance If you discover any faults stop the installation and contact the vendor Placement Place the appliance in the desired location The dishwasher is equipped with a water supply hose and a drain hose which can be connected either on the right or left hand side of the dishwasher Levelling the appliance After placing the dishwasher in its place it is not level you can level it by using the levelling feet Under no circumstances should the dishwasher be tilted by more than 2 Connecting to a power source WARNING For reason of personal safety Do not connect to an extension cord or a multi plug socket Under no circumstances remove or cut away grounding from the power cord Power source demands Information about the required voltage for the connection of the dishwasher to a suitable power source is contained on the appliance s rating label Use the required 10 16A fuse the recommended delaying fuse or circuit breaker and ensure that this appliance has its own independent electrical circuit A Before use check that the appliance is properly grounded EN 6 Copyright 2012 Fast CR a s Revision 10 2012 Electrical connection Check that the voltage and frequency of the used power source correspond to the information on the appliance s rating label Insert the power plug only into a properly grounded power socket If the socket to which the appliance will be connected is not properly gr
32. ry information about the correct disposal method from local government departments or from your seller C lt This product meets all the basic EU regulation requirements that relate to it Changes to the text design and technical specifications may occur without prior notice and we reserve the right to make these changes EN 35 Copyright 2012 Fast R a s Revision 10 2012
33. sernsdscensnevncansnnnnnvsooxrssbvdensenisediiovneaessons abedendonnchunnieaanebspbsavdeniasenonsseveavsash cdvnseseaennies 17 PART 5 WASHING DISHES CUTLERY ccscssscsssccsascssssssscsssscesveccssossssscescsasscsssssssessssvesesscssossccsccasscesssssscscosvessesss 18 TRIN NS AC Me cg sesccecfesececzcnegse sags tasnencvtbeszes eas teccnteccazescassassertavcaieorhissesta ayisseca cuss ose tty esacusearanes a 19 Filing the lower rack ig ssicccppszcunzecesecxosseanaena can sasstenstc consecntesstuiiaoayeadbicasdtesisssadsce ansedsaueassveatasescpaearasehiiseat ust ensseeaa aetatneateeaiens 19 s Setting the Upper TACK gsr cpuseceaztseqresosntezsecaesessessesitsconszecaneucqoisasaicosccxscehisseada estosecusueschee ces eassusearasesauseersiereasacvsmnssoueteay scoters 20 e Tilting down the tines in the upper rack essessssessssessssesssssssssessssescsescsesscsesscsesscsesscsessesesscsecsesecsssecssseeseseeasseeasseessaseess 21 We ASKS Or CUE e EEEE ENEN EEA E E drank VEAN A AEE E oaren 22 e Turning on the appliance starting a washing program sssssessessssssssssssssssssssscssssessssssesssssessssscsesssecsesseasseeseaeeaes 24 Changing a progra EE 24 PART 6 MAINTENANCE AND CLEANING ssscrsurserserderversereerterdenteorsndansentesssstorsenterenaads sesteohentenmentermsndersendeded 26 a Filtration Syste ensen deet nes vesten eroderen deedeetee 26 GSE ERSA ca vecescaceva E EE E A E men EEE E E E EES 26 e Cleaning the filter ssssesessseeesssssesss
34. sition in the front part of the upper rack as shown in the picture Serving spoons 1 Table spoons 2 Forks 3 Knives 4 Dessert spoons 5 Teaspoons 6 Ladles 7 8 Serving forks 12345678 WARNING e Ensure that no cutlery projects through the bottom of the basket e Always place sharp cutlery with the tip pointing downwards For your personal safety and to achieve the maximum quality way place cutlery into the basket ensuring that e individual items are not lying on each other e the cutlery is placed with the handle pointing downwards e place knives and other dangerous cookware with the handle pointing upwards EN 22 Copyright 2012 Fast CR a s Revision 10 2012 Program table Program Temperature Food types Degree of soiling Dishwashing detergent A 25 cm 15 cm B 5 cm Washing cycle process Washing cycle time min Intensive wash P1 Heavily soiled dishes for hygienic removal of soils A B Pre wash Wash 70 C Cold rinse Hot rinse Dishes soiled from soup sauces pasta eggs rice potatoes stewed meat fried foods A B Wash 65 C Cold rinse Hot rinse Economical wash P3 50 C Lightly soiled dishes from coffee milk tea cold meat vegetables B gt Pre wash Wash 50 C Cold rinse Hot rinse Quick wash 40 C Lightly soiled dishes from coffee milk tea cold meat vegetab
35. sseerssseeesssseessssseorsssreenssseenssseesssseeeossesressssteossseeeossesressseeosssstoeosssteossserorsserrossestesssstessssrerssseeres 27 e Dishwasher Care eseseesseeessesssessseesseesscesseesseesseesssesseeoseresecosscosscoseeeserenstosseossteseeesscesstosseeoseeesetosstosstosetosetestosstossteseeesscesseosseessees 27 e Protection against froSt sssssesssssesessseeesssseesssseeosssseeesssseenssseessssserossestossssteonsseeeosseerossseeorosseteosssteosssteorssterosseseesssseessssterosseeres 28 PART 7 PREVENTION OF MINOR MALFUNCTIONS eeessessssssssssssoosococececcesessssosossosssesocoecccecesesssssssssssssssseo 30 E ENOC ONOS aerie E AE A AOE ene 33 PART 8 TECHNICAL SPECIFICATIONS csssssscscsccoccssecassacensescnnshacsevadosssiacesesa tasendcnauntvnssbacencasensonccsccoseeetnacsasestsess 34 EN 1 Copyright 2012 Fast CR a s Revision 10 2012 PART 1 BEFORE PUTTING INTO OPERATION Important safety instructions e Read carefully and store for future use e The safety of this appliance complies with industry norms and meets legal appliance safety requirements However as manufacturers we consider it our duty to provide you with the following safety instructions e It is essential that you store this user s manual in a safe place so that you can use it in the future If you intend to sell the appliance give it to another owner or if you move always make sure that the user s manual is attached to the appliance so th
36. t arrangements of dishes Setting the upper rack Setting the height of the upper rack The height of the upper rack can be set so as to create more space for larger dishes in the upper lower rack The height of the upper rack can be set by inserting the wheels at various heights into the rails Long pieces of cookware eating utensils ladles and knives should be placed in the rack so that they do not interfere with the rotation of the spraying arms If you will not use a rack you may tilt it down or even remove it q A T ed a lo p_k J FS Ei B EN 20 Copyright 2012 Fast CR a s Revision 10 2012 Setting the height of the side partitions You can set the height of the side partitions to create more less room for larger smaller glasses cups in the top rack At the same time the side partitions are divided into 4 smaller sections so you can set 2 different heights on either side Tilting down the tines in the upper rack The lower rack is equipped with special tilting tines making it possible to quickly and easily adjust the lower rack area based on your current needs EN 21 Copyright 2012 Fast CR a s Revision 10 2012 Basket for cutlery Place cutlery into the basket with the handle downwards If the basket has side partitions place spoons separately into the appropriate openings Particularly long cutlery should be place in a horizontal po
37. t from the power socket Always disconnect the dishwasher from the power source before cleaning or any maintenance e No solvents or sandy cleaning agents Never clean the external or rubber parts of the dishwasher using solvents or sandy cleaning agents Only use a wiping cloth dipped in warm soapy water Remove stains from the surface of the dishwasher using a wiping cloth dipped in water with a little vinegar or a cleaning agent specially designed for dishwashers e When taking out of operation for an extended period We recommend that you run an empty cycle without dishes and then disconnect the dishwasher from the power source shut off the water supply and leave the dishwasher door slightly open This will help to increase the lifetime of the door seals and will prevent the accumulation of odours inside the dishwasher e Moving the appliance In the event that you need to move the appliance you must move it in the vertical position If it is really necessary place it down on its rear side e Seal One of the factors causing odours inside the dishwasher is food remains which get caught in the seals You can prevent this by regularly cleaning with a damp sponge EN 29 Copyright 2012 Fast CR a s Revision 10 2012 PART 7 PREVENTION OF MINOR MALFUNCTIONS Possible causes A burned fuse or the Replace the fuse or turn on the circuit breaker Disconnect circuit breaker is off any other appliances sharing the same cir
38. t performance if you follow these instructions for inserting dishes into the racks The function and appearance of the racks and the cutlery basket may differ depending on the model of the dishwasher NOTE Do not place any items into the dishwasher soiled by cigarette ash wax varnish or paint When buying new dishes check that they are dishwasher safe First remove remaining or burned on foods It is not necessary to wash dishes under running water Insert the dishes into the dishwasher as follows Items such as cups glasses pots pans etc should be placed bottom up Curved cookware and cookware with projections should be placed at an angle to allow water to freely flow out Place dishes safely so that they cannot tip over Place dishes in such a way that the spraying arms can rotate freely during the wash NOTE Do not wash very small pieces in the dishwasher because they can easily fall out of the rack EN 18 Copyright 2012 Fast CR a s Revision 10 2012 e Hollow cookware e g cups glasses pans etc should be placed bottom up so that water does not accumulate inside them during the wash Dishes and cutlery must not be inserted into each other or to cover each other To prevent damaging glasses they must not touch each other Place hard to clean large cookware in the lower rack The upper rack is intended for lighter and fragile dishes such as glasses cups and mugs Knives with a large blade placed i
39. the pre wash compartment This dose will be used during the pre wash phase of the wash NOTE You can find the information about dishwashing detergent dosages in the washing program table Keep in mind that the results may differ depending on the degree of soiling and hardness of the water used Follow the manufacturer s recommendations on the dishwashing detergent package EN 17 Copyright 2012 Fast CR a s Revision 10 2012 PART 5 WASHING DISHES CUTLERY e Purchase dishes designated as dishwasher safe e Useagentle dishwashing detergent marked as gentle on dishes If necessary seek out further information from the dishwashing detergent manufacturer e For certain types of dishes select a lower temperature e To prevent possible damage remove glassware and cutlery from the dishwasher as soon as possible after the end of the wash Unsuitable are cutlery with wooden bone or mother of pearl handles plastic parts that are not heat resistant older cutlery with glued parts that are not heat resistant glued cutlery or dishes tin or copper dishes crystal glassware metal parts susceptible to corrosion wooden cutting boards dishes made from synthetic fibres Partially suitable are e some types of glass may corrode after several washes e silver and aluminium cookware may become discoloured by the wash e glazed patterns may fade if washed frequently NOTE Your dishwasher will achieve the bes
40. ut the filtration system by unscrewing the coarse filter Remove any food remains and clean out the filters under running water NOTE You should clean the entire filtration set once per week Cleaning the filters To clean the coarse and fine filters use a brush Reassemble the individual parts of the filter as shown on pictures 1 2 and 3 Reinsert them back into the dishwasher in their place and press them downwards WARNING Do not knock on the filters when cleaning them Otherwise the filters could bend which would lower the efficiency of the dishwasher Never use the dishwasher without a filter An incorrectly seated filter may lower the efficiency of the dishwasher and cause damage to dishes Dishwasher care You can clean the control panel using a light damp wiping cloth Thoroughly dry the area after cleaning Clean the exterior parts of the dishwasher using a quality polish Never use any sharp items steel wool or coarse sandy cleaning products to clean any part of the dishwasher EN 27 Copyright 2012 Fast CR a s Revision 10 2012 Cleaning the door To clean the door edges use a soft warm damp wiping cloth To prevent water leaking into the door lock or its electronic parts do not use any cleaning agents in sprays WARNING e Never use cleaning agents in sprays to clean the dishwasher door because this could damage the door lock and electrical parts Do not use sandy cleaning agents or certain types of
41. vice centre The results of the wash are not satisfactory The dishes are not clean The dishes were not loaded into the dish washer correctly See chapter Washing dishes cutlery The program was not sufficiently intensive Insufficient amount of Use more dishwashing detergent dishwashing detergent or use a different one Dishes are blocking the Rearrange the dishes so that the spraying arms spraying arms can rotate freely Select a more intensive program See Program table The filters on the bottom of the dishwasher are not clean or correctly installed This may cause the spraying arm jets to become clogged Clean the filter or install them properly Clean out the spraying arms See Cleaning the spraying arms There is rust on glass Black or brown stains on plates Dishwashing detergent remained in the compartment Combination of soft water and an excessive dose of dishwashing detergent If you have soft water for cleaning and washing glass use less dishwashing detergent and a shorter cycle Aluminium dishes were leaning against the plates Remove these stains using a gentle cleaning agent The dishes blocked the lid of the compartinent Rearrange the dishes in the dishwasher Copyright 2012 Fast CR a s EN 31 Revision 10 2012 Drying results The dishes are
42. washing detergents reduces pollution and is appropriate for your dishes These programs are specifically improved with enzymes which are contained in concentrated dishwashing detergents that can dissolve soils For this reason you can achieve the same results with concentrated dishwashing detergents using a standard washing program as you would achieve only with the use of an intensive program Dishwashing tablets The dissolving speed of various brands of dishwashing tablets may differ For this reason some tablets may not dissolve during the short programs and therefore fail to perform their cleaning function So when using tablets use the long programs to ensure the removal of all dishwashing detergent remains Dishwashing detergent compartment You must fill up the compartment before starting any washing cycle according to the instructions contained in the dishwashing cycle table Your dishwasher uses less dishwashing detergent and rinsing aid than an ordinary dishwasher Generally a single tablespoon of dishwashing detergent is sufficient for a standard wash For more heavily soiled dishes you will need more dishwashing detergent Always add the dishwashing detergent immediately before starting the dishwasher otherwise it could become damp and subsequently not dissolve completely NOTE e Ifthe lid is closed press the button The lid will open e Always add the dishwashing detergent immediately before starting each washing cycle e Us
Download Pdf Manuals
Related Search