Imove 7s
Contents
1. 1 mul 0 MENU HH PAH Self Test Reset DMX512 Address Setting DMX512 Address Setting Show mode 1 Show mode 2 Show mode 3 Show mode 4 Slave Mode Normal Slave mode 2 Light Show Blackout Mode Yes Blackout Blackout Mode No Blackout _ Normal Color Split Color Pan Normal Pan Inversion Tilt Normal Tilt Inversion Dimmer Normal Dimmer Inversion LED on LED off Display Normal Display Inversion 9E Focus Adjust FES Fixture Hours Press the MENU button up to when the is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Stand by Blackout the unit X Y moving show Color Gobo selection X Y moving setting mode selection 1 Hold on for gobo 1 Pan position Show 1 Show 4 change 2 Tilt position Please refer to Show 2 Press shortly for 3 Dimmer mode in 4 2 Main color change First set Master unit Function then set Slave units position Mode sound 1 Sound 2 Slow Sound 3 Position Latch LED off LED norm2. 2 By easy controller 3 By iLead controller please refer to the user guide of iLead or by universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show IM8S IM7S on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 5 1 Master Slave Built In Preprogrammed Function cima tw be CL You can select blackout mode 24 110 jn 2 O0 yes blackout or no blackout mode while the unit is turned on By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to select Im i Zi I 2 C show 2 or x show 3 or Sih H show 4 mode by easy controller Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and show 1 or sound LED will flash to the music The other units will have to set in slave mode Std and select normal or 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave LED lights will constantly on 2 light show In Ltd slave
3. DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit 6E C Some units don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the unit Set the proper address D No response to the sound 1 Make sure the unit does not receive DMX signal 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition F The lamp is cutting out intermittently 1 The lamp is not working well Check the main voltage either too high or too low 2 Internal temperature may be too high Check and if necessary replace the fan on the head 2 1 Inserting Exchanging rotating gobos DANGER Install the gobos with the device switched off only Unplug from mains before changing gobos Open the cover by loosening the fastening screw at the sides of the cover If you wish to use other forms and patterns as the standard gobos or if the gobos are to be exchanged remove the fixation ring with an appropriate tool Remove the gobo and insert the new gobo Press the fixation ring together and insert it in the front of the gobo CAUTION Never unscrew the screws of t
4. the structure to which you are attaching the unit is secure and is able to support a weight of 30 kgs for each unit Below drawing is for IM 8S only Safety chain Mounting plate e en SF ES empl ne ue ee 7m pS ak 2 Technical Specification Power supply AC 120V 60Hz or 230V 240V 250V 50 60Hz Lamp Discharge lamp MSD 250 2 GY 9 5 IM 8S Discharge HTI 150W GY 9 5 IM 7S Optical system Standard 13 focused beam angle IM 8S Focus adjustable by DMX control Shutter Dimmer Blackout 0 100 smooth dimming and strobe speed variable 1 10 flashes per second Gobo wheel Independent gobo wheel with 7 gobos plus open gobos are interchangeable 4 metal gobos 2 glass gobos and 1 effect gobo Gobo wheel rotates with variable speed giving shaking effect Color wheel Independent color wheel with 9 dichroic mirrors plus white Color wheel rotates with variable speed giving rainbow effect 5E Movement Pan 540 in 2 8 second Tilt 270 in 1 6 second DMX Channels Standard DMX512 signal addressing and can be controlled by any universal DMX controller P IMS Channel 1 Pan motion Pan motion Channel 2 Tilt motion Tilt motion Channel 3 Shutter Shaking Shutter Shaking Channel 5 Channel 6 Gobo Rotation Channel 7 Dimmer Channel 8 Dimension 360mm x 397mm x 503mm IM 8S 373mm x 295mm x 451mm IM 7S Weight 26 kg IM 8S 13 kg IM 7S G
5. Specification 2 1 Inserting Exchanging rotating gobos 2 2 Beam angel 3 Lamp 4 How To Set The Unit 4 1 Control Panel 4 2 Main Function 5 How To Control The Unit 5 1 Master Slave Built In Preprogrammed Function 5 2 Easy Controller 5 3 iSolution Operation Universal DMX Controller 5 4 DMX512 Configuration 5 5 DMX512 Connection 6 Troubleshooting 7 Fixture Cleaning 1 Safety Instruction A WARNING Please read carefully the instruction which includes important information about the installation usage and maintenance Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit The unit is designed for use with the MSD 250 2 IM 8S or HTI 150 IM 7S Do not use any other type of lamp Its important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before fuse lamp replacement or servicing 3E Replace fuse lamp only with the same type Make sure there are no f
6. Technical Specifications IM 8S IM 7S AC 120V 60Hz or AC 230 240 250V 50 60Hz Fuse 20mm Glass T6 3A Fast Blow Dimension 373mm x 295mm x 451 mm Weight 13 kg Innovation Quality Performance Z Solution Your integrated Solution LINKABLE oes STAND ALONE User Guide Professional Entertainment Technology 7 Fixture Cleaninc The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC 2E EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements TABLE OF CONTENTS 1 Safety Instruction 2 Technical
7. To go back to the functions without any change press the MENU button again Pan Inversion is showing on the display Pressing ENTER Press the MENU button up to when the i button and the display will blink Use DOWN and UP button to select the pan inversion mode Once the mode has been selected press the ENTER button normal or to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU buiton again Tilt Inversion Press the MENU button up to when the 1 CLE jg showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the tilt inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU buiton again 11E normal or Dimmer Inversion Press the MENU button up to when the 5 button and the display will blink Use DOWN and UP button to select the dimmer inversion mode Once the mode has been selected press the ENTER is shown on the display Pressing ENTER normal or button to setup or automatically return to the main functions without any change after 8
8. XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 4 DMX512 Configuration IM 7S without Channel 8 Focus DMX512 Configuration Ch Cch Ch3 248 255 Open 255 Fastest speed Gobo change 247 Fastest speed Shaking 4h fy 4 128 Slowest speed Gobo change 112 127 132 Slowest speed shaking 131 Fastest speaad shutter j A 046 063 032 047 16 Slowest speed shutter 008 015 Open 000 007 Blackout Q A O 016 031 000 015 obo Rotation Dimmer Focus 255 Fatest speed Rainbow affect 128 Slowest speed Rainbow effet 116 127 Pink 103 115 Light Green 090 102 UV Purple OF 7 089 Blue 064 076 Orange 052 063 Yellow 039 051 Light Blue 026 038 Magenta 013 025 Green 000 012 White 255 Fastest speed Rainbow effect P 128 Slowest speed Rainbow effect 121 127 Pink 113 120 Light Green 106 112 UVP urple light Green 098 105 UV Purple 091 097 Blue UV Purple 083 090 Blue 076 082 Orange Blue 068 075 Orange 061 067 Yellow Orange 053 060 Yellow 046 052 Light Blue Yellow 038 045 Light Blue 031 037 Magenta Light Blue 023 030 Magenta 016 022 Greent Magenta 008 015 Green 000 007 White 246 255 Stopped 245 Fastest speed clackwise 135 Slowest speed clockwise 121 134 Stepped 120 Slowes
9. al blinking LED on LED fast blinking 5 3 1 iSolution Operation Strobe 1 Gobo Color sync strobe Function 2 Sync strobe 3 Two light strobe Consistent DMX configuration enable iMove to be linked together with iRock and iShow and controlled at the same time DMX address can be set remotely by iLead controller please refer to the user manual of iLead controller No need to calculate the DMX channels of each fixture in the chain Automatic switching between DMX function and built in stand alone programs 5 3 2 DMX Controller An universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the Moor js showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units DMX address can be setting remotely by IL 0824 controller No need to calculate the DMX channels of each fixture in the chain LLL es 5 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogram function
10. d under ceiling The spot is mainly projecting in front of the stage Pan movement angel left to right to left 160 Tilt movement angel 90 vertically front 75 back 15 Slave Mode Press the MENU button up to when the SLiic is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the normal or 2 light show mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again I Blackout Mode Lid is showing on the display Pressing ENTER Press the MENU button up to when the m button and the display will blink Use DOWN and UP button to select the 3 00 yes blackout or C no no blackout mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU buiton again Color Mode Press the MENU button up to when the IO is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the S normal or 2L split color mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds
11. he rotating gobo as the ball bearing will otherwise be opened 2 2 Beam angel IM 8S IM 7S Lamp HTI 150W Beam angle 13 degree 383 lux 3770 734 382 191 lux Se ey Eff Lamp MSD 250 2 Bea 6470 1503 756 mangle 13 degree e pe O 2 5 7 8 10 Oo 2 8 5 7 8 10 Distance m Distance m In case of replacement of the lamp or maintenance do not open the fixture within 15 minutes until the unit cools down after switching off Because of its high internal pressure there might be a risk that the Discharge lamp would explode during operation The lamp emits intense UV radiation which is harmful to the eyes and skin The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp 7 Discharge lamp MSD 250 2 IM 8S HTI 150W IM 7S Always switch off the main supply and never handle h the lamp or luminaries when is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age temperature and improper handling eS E EL of the lamp Do not use the lamp any longer than its A b an specified life 3 TN er reflector for the best spot Ad
12. just lamp position by ge ee screws A B and C 7E 5 5 DMX512 Connection The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels DMX512 120 ohm 174W COMMON Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMA and pin3 DMA of the last fixture 1 If you use a controller with 5 pins DMX connector you need to use a 5 to 3 pin adapter 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMxX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not branched or split to a Y cable DMX512 Is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 6 The end of the DMX512 system should be terminated to reduce signal errors 7 3 pin
13. lammable materials close to the unit while operating as it is fire hazard Use safety cable when fixes this unit Don t handle the unit by taking its head only but always by taking its base Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85C Don t touch the housing bare hand during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing bulb or serving In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to any dimmer pack or power pack Do not touch any wire during operation as high voltage might be causing electric shock H If The IM 7S pan belt is broken Turn off the main power Unscrew all the screws A and open the base housing cover B Unplug all the connect wires C that from the arm to PC board and igniter Unscrew the screws D that fix the bridge E Unscrew the screws F that fix the axis gear G Ooo FW N Change a new belt H by going through all connecting wires that from the arm to base and through the bridge for correct position 7 Set up the gear axis to the bridge and scre
14. mode means the unit works normally and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 5 2 Easy Controller The easy remote controller is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote control on the first unit will control all the other units for Stand by Function and Mode 10E Show Mode Press the MENU button up to when the Sri is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the Sol anc show 2 or show 3 or ahi H show 4 mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions show 1 or without any change after 8 seconds To go back to the functions without any change press the MENU button again Show 1 mode Fixture is placed on the floor Tilt movement angle 210 Show 2 mode Fixture is fixed under ceiling Tilt movement angle 90 Show 3 mode Fixture is placed on the speaker The spot is always projecting to the audience s direction i e in front of the stage Pan movement angel left to right to left 160 90 horizon Tilt movement angel 60 above horizon 30 below Show 4 mode Fixture is fixe
15. nctions press the MENU button again lll Self Test Press the MENU button up to when the cese is blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again Fixture Hours Press the MENU button up to when the car oi js blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again LOL I JLL Reset Press the MENU button up to when the 22C js blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again
16. obo Rotation Dimmer G If The IM 8S pan belt is broken Turn off the main power Unscrew all the screws A and open the base housing cover B Unplug all the connect wires C that from the arm to PC board and igniter Unscrew the screws D that fix the bridge E Unscrew the screws F that fix the axis gear G oak won Change a new belt H by going through all connecting wires that from the arm to base and through the bridge for correct position 7 Set up the gear axis to the bridge and screwed it Note do not press the belt 8 Put the belt around the axis gear and motor gear 9 Plug all the connect wires C that form the arm to PC board and igniter 10 Adjust the pan home position 11 Screw the base housing cover B 6 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connection of power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 Ifthe DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another
17. seconds To go back to the functions without any change press the MENU button again Led Display is showing on the display Pressing ENTER Press the MENU button up to when the L button and the display will blink Use DOWN and UP button to select the Ltt Led off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go Led on or back to the functions without any change press the MENU buiton again Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button up to when the is blinking on the display Use the ENTER button to change to the mode oar display inversion It will automatically store after 8 seconds Or press the ENTER display normal To go back to the functions press button again return to the mode the MENU button toe Display normal mode for the fixture putting on the floor Display inversion mode for the fixture fixing under ceiling Focus Adjust Press the MENU button up to when the CAOL ig blinking on the display Pressing ENTER button the unit will focus on tilt 90 and then the unit will focus on pan 0 pan 90 pan 180 pan 270 in every pressing ENTER button Use DOWN and UP bution to adjust focus To go back to the fu
18. t speed counterclockwise 0 010 Fastestspead counterclockwise 000 008 Stopped 8E 4 How To Set The Unit 4 1 Control Panel MENU DOWN UP REMOTE CONTROL Display To show the various menus and the selected functions LED DMX input present MASTER On Master Mode Slave Mode Button MENU To select the programming functions DOWN To go backward in the selected functions To go forward in the selected functions To confirm the selected functions Remote controller input By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode Sensitivity To adjust the sound sensitivity Microphone To receive audio signal for sound activation DMX input output For DMX512 link use 3 pin XLR plug cable to link the unit together 4 2 Main Function To select any of the pre set functions press the MENU button up to when the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to setup or it will auto any change after idling 8 seconds To go back matically return to the main functions without to the functions without any change press the MENU button The main functions are shown below gt as wi a Z u ha It gt ie X E uw aL We Ty fy Ea a
19. wed it Note do not press the belt 8 Put the belt around the axis gear and motor gear 9 Plug all the connect wires C that form the arm to PC board and igniter 10 Adjust the pan home position 11 Screw the base housing cover B Pay attention to the belt tension when install the belt Please refer to the photos below For IM 8S Pressed Photo 1 Normal 77E N S35 fi J n hE SS __ i BSS ea Py BIC FA Ly S 5 nt 2 ra Ss ae am Pressed Photo 2 4E Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Never touch bulb with bare fingers as it is very hot after using Hot lamp explosion hazard Do not open the unit within five minutes after switching off Do not start on the unit without bulb enclosure or housing are damaged gt The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Do not look directly at the light while the bulb is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that
Download Pdf Manuals
Related Search