V-max - Manual Handling Solutions
Contents
1. Socket for power cable on the V max Control panel Socket for power cable out and charging cable in 1 1 4 Control panel Push button ON OFF Indicator of battery charge and malfunction Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK v max Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com AAT Ideen bewegen mehr V max 1 2 Technical data Height 24 cm Measurements Width 47 5 cm Depth 18 5 cm Driving unit including grips 8 5 kg Battery pack 8 6 kg Weight Power cable 220 g Battery bag plus Velcro straps 180 g Battery charger 740 g Seat s width minimum 36 cm maximum negative Margins for mounting the V max to the wheelchair ren Maximum permissible total weight 200 kg person wheelchair V max continuously adjustable Speed 6 km per hour forward 3 km per hour backward Capacity with one battery pack up to 15 km Maximum slope up to 20 Batteries 2x12V 12 Ah Direct current motor 24V Limiting values stipulated by the wheelchair manufacturers must be no ted and observed Range and climbing capacity depend on the weight of the person who is transported as well as on the floor surfaces the ground the terrain etc Weight and climbing diagram Slope 20 15 Dt 1 M 10 o 0 40 kg 80 kg 120 kg 160 kg 200 kg2. Total weight In the interest of progress we reserve the right for technical changes Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 6 AAT Ideen bewegen mehr 1 3 Delivery package The delivery package contains Wheelchair wheels including handrim and toothed ring V max driving unit plus pushing and control grip Battery pack plus bag Operator s manual Charger plus operator s manual aS well as the components mounted to the wheelchair such as the bra cket power cable and the bag for the battery pack no picture In addition a holding device is necessary which is atteched to the wheel chair beforehand 1 4 Optional accessories Anti tilt support Voltage transformer for the car Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 7 AAT Ideen bewegen mehr V max 2 Assembly and Operation The V max can only be used in connection with a special bracket which must be mounted to your wheelchair This bracket may only be mounted by AAT or dealers authorized by AAT 2 1 Brackets All brackets are especially developed and adjusted to each individual wheelchair which means
3. V max starting from the date of purchase The warranty covers faulty ma terial and manufacturing defects The warranty does not include e natural wear and tear e damage caused by operation beyond set limitations e damage caused by improper handling e forced damage e unauthorized changes made on the device and or its accessories 8 2 Liability Neither AAT Alber Antriebstechnik GmbH nor its agents or authorized dea lers and sales representatives are liable for the safety reliability or perfor mance of the V max or for any claims for personal Injury or property damage which may arise from the following e the V max was handled and used inappropriately e the V max was not checked every two years by an authorized dealer or AAT GmbH e the V max was used not in accordance with all instructions and pre cautions included in this user s manual e the V max was used with Insufficient battery charge e assembly repairs or other work was done by unauthorized personnel e parts or accessories other than those recommended by the manufac turer of the V max were used parts of the V max were changed or removed entirely Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK v max Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com eo AAT Ideen bewegen mehr AAT Alber Antriebstechnik GmbH Postfach 10 05 60 D 72426 Albsta
4. be performed by the company AAT Alber An triebstechnik or their authorized dealers The V max may only be attached to wheelchairs whose seats measure at least 36 cm All wheelchairs must be checked according to generally ac knowledged technical norms and their operators manuals must be ap plied when using the V max When operating the V max all stipulations required by the wheelchair ma nufacturer such as e g maximum gradient or maximum load as well as all other general guidelines must be observed Indicated limitations are not to be exceeded under any circumstances 5 The maximum total weight of 200 kg is composed of the weight of the person to be transported plus the weight of the wheelchair and the V max 3 3 Correct use attendant Thorough instruction into the use of the v max by your dealer or a repre sentative of AAT Alber Antriebstechnik is part of the delivery package and takes place at an appointment of your choice This is a free service at no extra charge 5 Do not use the v max without being trained to operate it 5 Only an attendant and not the wheelchair driver him or herself may use the pushing and braking aid V max because of the danger of til ting the wheelchair especially when driving on slopes 5 In the interest of your safety the v max may only be operated by peo ple instructed in the use of the device and further by people who are physically and mentally capable to manage the V max in al
5. that the bracket right left pictured in this operator s manual may differ from the one attached to your wheel chair 5 Before each use check whether the bracket is securely fastened to the wheelchair In case screws have loosened or fallen out you may not use the V max Please contact your dealer immediately 2 2 Battery pack A bag for the battery pack is attached under the seat of the wheelchair Simply slide the battery pack into its bag and fix it with a Velcro strap Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 8 AAT Ideen bewegen mehr 2 3 Hook on the V max p gt I To mount the V max the powered axles must be inserted entirely Press the two buttons toward the PRESS button until they lock See pictu N K re on the right Now slide the v max evenly on both sides into the brackets AR 5 Make sure the v max with its wheelchair links is in a straight line yi when you insert it into the brackets Then the machine slides automatically into the appropriate place in Q the brackets AA Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com g AAT Ideen bewegen
6. 4 sales manualhandlingsolutions co uk www manualhandlingsolutions com 11 VA Ideen bewegen mehr v max 2 4 1 Attaching the grips Due to the special toothing it is possible to insert the grips into the grip holders in the most comfortable position for each individual users See picture on the right indicating the grip positions which have proven most comfortable for frequent use 2 4 2 Removal of the grip Pull the locating pin The grip unlocks and you can lift it out of the link Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com ie AAT Ideen bewegen mehr v max In case you do not need the device for some time simply remove the grips and put them back into their respective holders and on the V Max If you like remove the V max entirely from the wheelchair and set the de vice on its grips which function as sturdy legs in such case Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 13 AAT Ideen bewegen mehr V m ax 2 5 Anti tilt support You may only use V max if anti tilt supports have been attached to your wheelchair If your wheelchair is not equipped with anti tilt supports we offer them as a
7. AT Ideen bewegen mehr Table of contents CE declaration of conformity Table of contents 2 2 nn m nn 288 eae 1 Introduction 2 2 nn mn nn nn 1 1 Product description ao 2 2 2 2 2 m nn nn 1 2 Technical data 2 nn m m nn Lo Delivery package 2 2 2 2 nn m nn 1 4 Optional accessories a 2 2 2 2 2 0 2 ee eae 2 Assembly and Operation a 2 2 2 nn 0 m m nn nn 2 Brackets 2 2 2 2 nn nn nn 2 2 Battery pack 2 2 m a u a Zid Attaching the V max 2 2 nn ee ee 2 4 Control grip and pushing grip 2 5 Anti tilt support aoao a a a nn nn 3 Safety instructions and awareness of potential hazards 3 1 General information m nn nn 22 Technical requirements 4 I Correct use of the V max 2 2 2 2 nn 3 4 Environmental influences 35 Driving 5 5 SSG owe aw a Rw Rw KG 3 6 Special instructions 2 nn m nn 4 Display and control elements a 2 2 2 2 nenn 4 1 Control grip owes bee Kwa eee Oe we 4 2 ON OFF switch m nn eee eee 4 3 LED control lights for battery charge 5 Battery pack 1 ee Dic General information concerning the type of battery 072 ee re me ee a ee ER 9 2 Change of fuses 2 2 2 nn m nn eee eee Trouble shooting malfunction 2 2 2 2 u 2m Care maintenance and recycling disposal Tad Cale r vee ee he Ja Maintenance n
8. Pushing and Braking Aid v max User s Manual Ideen bewegen mehr Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com AAT Ideen bewegen mehr V max CE Declaration of conformity The company AAT Alber Antriebstechnik GmbH herewith declares that the products of the power system V max are developed and manufactured ac cording to the general guidelines 93 42 EWG of the European Union This declaration loses all validity if the above mentioned devices have been tampered with or changed in any way without the knowledge and agreement of the company AAT Alber Antriebstechnik CE Signature of the manufacturer Markus Alber Managing partner Hd a la Yih AAT Alber Antriebstechnik GmbH The power system V max is being tested according to the norm DIN EN 12184 C11 99 at the institution for certification of medical products GmbH Technical University Berlin TESTED AND MONITORED AAT Alber Antriebstechnik GmbH P O Box 10 05 60 D 72426 Albstadt AAT Tel 49 74 31 12 95 0 Fax 49 74 31 1295 35 info aat online de www aat online de v max_gb_11 06 Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com A
9. al they are probably used up In such case have your batteries checked by your local dealer and ex changed If necessary 5 Always charge your battery pack with the AAT charger delivered with your V max This particular charger automatically turns off when the batteries are fully charged keeping them from being overcharged 5 1 1 Charging the batteries attached to the wheelchair To charge the batteries you may leave the battery pack in its bag attached to the wheelchair First pull the plug of the power cable then Insert the plug of the charger entirely into the charging socket Finally plug the charger into the wall socket 5 During the charging process the LED display shows a constant red light 5 As soon as the charging process is finished the LED display blinks red Afterwards you first remove the charger s plug from the wall socket and then you pull the plug from the charging socket Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 19 AAT Ideen bewegen mehr V max 5 1 2 Charging the batteries in your vehicle By means of a voltage transformer you may even charge your battery pack while driving your car First remove the power cable Then fully insert the plug of the charger into the charging socket on the battery pack Then connect the cha
10. c brake is activated However for safety reasons the electro magnetic brake is activited imme diately after releasing the rocker switch 5 Depending on the driving situation the strong effect of the elec tro magnetic brake may bring the wheelchair to an immediate ab rupt stop The panic switch works in both directions of driving forwards and bac kwards 4 2 ON OFF push button A number of LED s located on the control panel next to the On Off button inform you about the charge of the battery If you have not used the V max for longer than 5 minutes it turns itself off automatically In such case press the button again to reactivate the device 4 3 Battery charge A number of LED s located on the control panel next to the On Off button inform you about the charge of the battery LED s and their meaning If the diode lights up in the first green column the battery pack is 100 charged the second green column the battery pack is 80 charged the third green column The abattery pack is 60 charged the yellow column the battery pack is 40 charged the red column the battery pack is 20 charged If the LED in the red column lights up you must recharge the battery pack Due to the extensive self tests of the electronics it is possible that the charge indication only shows 80 even though the batteries are full Please wait approximately one minute then the charge will be indicated corre
11. ctly Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 18 AAT Ideen bewegen mehr V max 5 Battery pack The battery pack of the V max is maintenance free and rechargeable Its durability depends directly on the number of charging discharging cycles 5 1 General information concerning the battery pack If you take good care of your battery pack by recharging it regularly you prolong its durability The V max s electronics constantly check the battery s charge and thus prevent a total discharge if used adequately 5 Avoid a total discharge of the battery pack Recharge it after each partial discharge i e after each use of the V max The battery pack undergoes a so called self discharge therefore you should connect your battery pack whenever possible to a charger The charging automatism which switches from charging the battery to retail ning the charge when it is full kicks in and keeps the battery from overcharging If your battery pack has not reached its full capacity it is possible that with a new battery pack it takes a few charging discharging cycles to build up the full capacity The battery pack can be charged in any position It is considered as safe as dry cells and admitted to air travel by DOT and IATA If fully charged batteries empty faster than usu
12. dt Tel 0 7431 12950 Fax 0 74 31 12 95 35 Email info aat online de www aat online de Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com
13. g the batteries whene ver possible 5 Charging and taking care of your batteries is the same thing in this case If fully charged batteries empty faster than usual they presumably are used up Have them checked by your local dealer or an AAT representati ve and if necessary exchanged 7 1 2 Cleaning Please clean your control unit driving unit battery pack and brackets with a mild household cleaner 5 Make sure that no water gets into the v max therefore merely use a damp cloth for cleaning 5 In the interest of your safety do not use a high pressure cleaning de vice 7 2 Maintenance The V max Is a device particularly low in maintenance Nevertheless for safety reasons your v max needs to be checked once every 2 years even though there may not be any malfunction or outer damage Please contact your dealer or your AAT representative concerning the maintenance work 7 3 Disposal Your V max and its battery pack are products with a long durability Once the device Is old and out dated you may return it to AAT Alber Antriebs technik GmbH or your local dealer for disposal Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com ec AAT Ideen bewegen mehr 8 Warranty and liability 8 1 Warranty There is a 24 month warranty 6 months on the battery pack on the
14. ield Please turn the device OFF and ON again If the device Is still indicating malfunction charge the batteries in case of low voltage In all other ca ses please contact your dealer Red LED blinks Type of malfunction ie Malfunction of the motor the motor controller or the battery pack 2X Low voltage batteries empty 3X Overvoltage Ax Electro magnetic brake at fault DX Electronics damaged 6x Electronics damaged We purposely avoided the activation of the electro magnetic brake as soon as the device recognizes a malfunction of some kind 5 If you want to activate the electro magnetic brake push the rocker switch hard to overcome the pressure point and the panic switch is activated Then release the rocker switch Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 21 AAT Ideen bewegen mehr V max 7 Care maintenance and recycling The v max does not call for particular maintenance and in contrast to the batteries special care except for occasional cleaning see chapter 7 1 2 is not necessary 7 1 Care 7 1 1 Battery pack The V max s batteries are air tight maintenance free rechargeable and of excellent quality Total discharge leads to loss of capacity as well as a shorter durability 5 Therefore avoid a total discharge by rechargin
15. l situa tions that may occur while using it The attendant must be able to catch the wheelchair plus the person sit ting in it if the chair should tilt backwards Anti tilt supports are obligato ry 5 Should you feel insecure handling the v max please contact your dealer or one of the AAT representatives Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 19 AAT Ideen bewegen mehr 3 4 Environmental influences electromagnetic compatibility Electromagnetic compatibility signifies the capacity of an electric device to function satisfactorily in its electromagnetic environment without inter fering with other devices that are also in said environment The v max successfully passed all the EMV tests required by law 3 5 Driving Generally all limits of your wheelchair specified by the manufacturer must be observed and not exceeded 5 Always put your speed control in the position of its lowest possible speed when you start driving Although the V max manages gradients up to 22 never exceed the ma ximum gradient stipulated by the manufacturer of your wheelchair It is obligatory to use anti tilt supports 5 Be careful when you drive downhill for quite some time with full bat teries Driving downhill generates electricity which charges the bat teries additional
16. ly This can lead to overvoltage The v max goes into coast and must be stopped manually or by means of the emergency switch Please see chapter 4 1 3 Panic switch 3 6 Special instructions for operation If the V max is turned off the wheelchair cannot be moved manually the driving unit is blocked up In order to achieve the desired braking effect you must turn on the V max 5 The v max can be stopped at any time be it during regular operati on an emergency situation or when malfunctioning by pushing and releasing the panic switch Please turn to chapter 4 1 3 for further information on the panic switch v max Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 16 AAT Ideen bewegen mehr V max 4 Control and display elements Your V max is ready to go when you receive it Once the V max is correctly mounted and connected you can turn it on and use it immediately Please practise using it with an empty wheelchair to get a feeling for the machine and its functions This also applies to the panic switch system 4 1 Control grip The wheelchair driver s attendant uses all of the V max s functions by me ans of the control grip 4 1 1 Speed control The speed control allows you to pre select the speed 5 Turn the speed control counter clockwise all the way for minimum s
17. mehr V max Now you press the PRESS button to unlock the levers and the powered axles come out The power unit is activated if both buttons have reached their ou ter position 5 The driving unit locked properly if the wheelchair cannot be moved manually any more Now you can insert the plug of the power cable into its socket on the V max Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 10 Luu Ideen bewegen mehr v max Then you put the other plug of the power cable into its socket on the battery pack 2 4 Pushing and control grip The wheelchair driver s attendant controls all functions of the v max by means of the control grip Since the control grip and the pushing grip can be installed either on the right or the left side the V max is ideal for both right handed or left handed users At the ends of the regular wheelchair grips links are attached into which you can stick both grips of the V max on either side These particular grip holders allow the user to insert either one of the grips in various positions on the right or the left side so an individual and comfortable adjustments ot the grips is possible Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK Tel 0044 1553 811977 Fax 0044 1553 81100
18. n optional accessory with the V max Particular fixtures for these anti tilt supports are already integrated into the brackets of the V max 2 5 1 Attaching and removing the tilt supports Insert the anti tilt support entirely into the V max s bracket Then lock the anti tilt support with the safety pin Slide the safety pin all the way into the hole drilled into the bracket while pressing the unlo cking button in the middle of the safety pin s head Then release the unlocking button 5 Always check whether the safety pins sit securely in the bracket Make sure they cannot be removed without pressing the unlocking button 2 5 2 Removing the anti tilt supports Press the unlocking button and keep it pressed to take out the safety pins Now you can remove the anti tilt supports Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 14 AAT Ideen bewegen mehr V max 3 Safety instructions and awareness of potential hazards 3 1 General information All general rules for the safe use of a wheelchair apply without reservation while operating the V max To assure the safe use of the V max it is indispensable to observe the fol lowing directions 3 2 Technical requirements Attaching the brackets of the V max on the wheelchair or making changes on said brackets can only
19. oaoo 2 nn ee ee ee es 7 3 Liabily a s 2 u 4 5 2 u RR A ER aa He 8 Warranty and liability 8 1 Warranty a aoao a n 8 2 Liapillty s gett ESE Shee SRE SE Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 OTQ UK VXOrOoO NN PP W N V max Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 3 AAT Ideen bewegen mehr V max 1 Introduction v max is a newly developed pushing and braking aid operated by an assi stant The device directly propels the back wheels of a wheelchair Compared to common power systems the V max possesses considerable advantages such as e g a permanent and efficient power transmission 1 1 Product description 1 1 1 Main features E Control grip E Driving unit Wheels plus handrim and toothed ring Brackets on the wheelchair Anti tilt support Battery pack plus bag and Velcro strip D Pushing grip Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com A AAT Ideen bewegen mehr 1 1 2 Control grip Speed control Rocker switch backwards forwards Link to hold grips Helix cable 1 1 3 Driving unit Battery pack Control grip Power switch Driving units link to the wheelchair
20. peed You must begin with minimum speed when you use the V max for the first time 4 1 2 Rocker switch With the rocker switch you determine the direction and speed up to the pre selected speed of the V max 5 Use the rocker switch carefully To drive forward press the longer back part of the rocker switch To drive backward press the shorter front part of the rocker switch The v max speeds up the more you press the rocker switch until you reach the maximum pressure point It slows down the more you release the ro cker switch If the user lets go of the rocking switch altogether and it reaches its neut ral position the power comes to a standstill To increase the braking ef fect the power reverses poles Two seconds after standstill is reached an electro magnetic parking bra ke becomes active Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 12 AAT Ideen bewegen mehr V max 4 1 3 Panic switch If during an emergency you press the rocker switch too hard so that the pressure point is overcome the so called panic switch causes the V max to go from driving mode into coast As long as you keep the rocker switch pressed you can drive the patient away from the dangerous situation However as soon as you release the rocker switch the electromagneti
21. rger to the voltage transformer Finally you plug the transfor mer into the cigarette lighter Afterwards you first pull the transformer s plug from the cigarette lighter before you disconnect it from the charger 5 2 Change of fuses The battery pack has two fuses each 30 A in a drawer Once the lower fuse is burnt out replace it by the upper extra fuse If a change of fuses IS necessary put a pin in the opening on the side of the battery pack This unlocks the drawer so you may pull it out 5 Always use the same 30 A fuses Manual Handling Solutions 58 Paige Close Watlington Kings Lynn Norfolk PE33 0TQ UK Tel 0044 1553 811977 Fax 0044 1553 811004 sales manualhandlingsolutions co uk www manualhandlingsolutions com 20 AAT Ideen bewegen mehr V max 6 Trouble shooting malfunction If there are problems using the V max please check the following trouble shooting chart and see whether you can fix them yourself Problem Check and potential solution Is the charger connected to the V max If so remove charging cable and connect the power cable Battery pack is empty If so charge the batteries V max cannot be turned on Fuse is damaged If so exchange the fuse If the V max still cannot be turned on contact your local AAT dealer Batteries do not charge Call your local AAT dealer Malfunction is indicated by a blinking red light diode in the control f
Download Pdf Manuals
Related Search