DSM800 Vessel Monitoring and Control Indoor Display User`s Manual
Contents
1. Chassis Support Screws Page 4 Revision 1 0 Maretron Step 9 Secure the DSM800 by fastening the retention screw of the wall mounting bracket Figure 4 Figure 4 Secure the DSM800 2 3 2 Panel Mounting To mount the DSM800 using the optional panel mounting kit Maretron part number MAFLPK 12 please follow the steps below Please note that the clamps found within the panel mounting kit support a maximum panel thickness of 3 8 or 0 375 Step 1 Select the position on the panel to mount the DSM800 Step 2 Cut out a section from the panel that corresponds to the rear panel dimensions of the DSM800 Take care that the panel section that is cut out is smaller than the overall size of the metal frame that surrounds the DSM800 but just large enough for the rear panel of the DSM800 to fit through Figure 5 Revision 1 0 Page 5 DSM800 User s Manual Suggested 9 Cut out size gt gt A E SS Figure 5 DSM800 Cutout Dimensions units in mm Step 3 Slide the DSM800 through the hole until the aluminum frame is flush against the panel Step 4 Insert the panel mounting clamps into the pre formed holes along the edges of the chassis behind the aluminum frame 6 clamps come with the optional panel mount kit 4 clamps are used and two are extras Step 5 Tighten the screws that pass through the panel mounting clamps until the plastic caps at the front of all the screws are firmly secured to the2. OR OTHER THEORIES OF LAW WITH RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY MARETRON OR ANY UNDERTAKINGS ACTS OR OMISSIONS RELATING THERETO Maretron does not warrant that the functions contained in any software programs or products will meet purchaser s requirements or that the operation of the software programs or products will be uninterrupted or error free Purchaser assumes responsibility for the selection of the software programs or products to achieve the intended results and for the installation use and results obtained from said programs or products No specifications samples descriptions or illustrations provided Maretron to Purchaser whether directly in trade literature brochures or other documentation shall be construed as warranties of any kind and any failure to conform with such specifications samples descriptions or illustrations shall not constitute any breach of Maretron s limited warranty Page 22 Revision 1 0 Maretron Warranty Return Procedure To apply for warranty claims contact Maretron or one of its dealers to describe the problem and determine the appropriate course of action If a return is necessary place the product in its original packaging together with proof of purchase and send to an Authorized Maretron Service Location You are responsible for all shipping and insurance charges Maretron will return the replaced or repaired product with all shipping and handling prepaid except for requests req
3. connection with which Maretron s products or parts shall be used With respect to products not manufactured by Maretron Maretron s warranty obligation shall in all respects conform to and be limited to the warranty actually extended to Maretron by its supplier The foregoing warranties shall not apply with respect to products subjected to negligence misuse misapplication accident damages by circumstances beyond Maretron s control to improper installation operation maintenance or storage or to other than normal use or service THE FOREGOING WARRANTIES ARE EXPRESSLY IN LIEU OF AND EXCLUDES ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE Statements made by any person including representatives of Maretron which are inconsistent or in conflict with the terms of this Limited Warranty shall not be binding upon Maretron unless reduced to writing and approved by an officer of Maretron INNO CASE WILL MARETRON BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES DAMAGES FOR LOSS OF USE LOSS OF ANTICIPATED PROFITS OR SAVINGS OR ANY OTHER LOSS INCURRED BECAUSE OF INTERRUPTION OF SERVICE INNO EVENT SHALL MARETRON S AGGREGATE LIABILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT S INVOLVED MARETRON SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES WHETHER ARISING OUT OF BREACH OF CONTRACT OR WARRANTY TORT INCLUDING NEGLIGENCE
4. highest standards for years of dependable and accurate service The DSM800 is a dedicated touch screen that comes preloaded with Maretron s N2KView vessel monitoring and control software N2KView hardware license key sold separately The N2KView software allows you to configure as many favorite screens as you want with exactly the information you want to see Although not suitable for outdoor applications the DSM800 provides an extremely simple touch interface for monitoring and controlling critical systems from inside the vessel The DSM800 is ruggedized for marine use and includes a solid state disk drive to withstand the pounding associated with waves And since the DSM800 only dissipates 25 watts there is no need for internal cooling fans that are noisy and wear out causing electronics to overheat and fail As an alternative to controlling the DSM800 through the touch screen the DSM800 includes two USB ports for connecting keyboards mice or trackballs The DSM800 also has an Ethernet port for communicating with an NMEA 2000 network see Figure 1 through Maretron s Internet Protocol Gateway IPG100 Alternatively the DSM800 can network through Ethernet to a PC running N2KServer Although the DSM800 comes pre installed with the N2KView software a separately purchased N2KView hardware license key plugged into the IPG100 or PC is required see IPG100 User s Manual for more details The Ethernet port is also used for connectin
5. 1 Turning the LEET ed 17 3 2 Turning the DSM800 Off rset nete aie ete tao snd ta A Bl e et Bi tel 17 3 3 Using the DSM800 n sc eee saca a ei tat teii a intii tai toi 17 4 dal 18 5 TET OM 19 6 Technical Specifications n ee taci eu aie pane iai tt an i in nea 20 7 Tenne E OM tame eee ema id iati tn bat 21 8 Maretron 1 Year Limited Warranty nana nana 22 Revision 1 0 Page iii DSM800 User s Manual Table of Figures Figure 1 DSM800 Network Diagram ENEE 1 Figure 2 Wall Mounting Bracket EE 4 atelier 4 Figure 4 Secure the DSMEDD ae Seg 5 Figure 5 DSM800 Cutout Dimensions units in mm 6 Figure 6 Tighten the Panel Mounting Clamp Screws ENEE 7 Figure 7 DSM800 Arm Mounting Retention Screw Holes rrrrrnnnnnnnrrrnnnnnnnnnnnnnnnnrrrnnnnnnnnnnrnnnnnrrnnennne 8 Figure 8 DSM800 Interface Connector Panel unn 9 Figure 9 LAN COME 9 Figure 10 USB Device Connection eseu 10 Figure 11 DSM800 Startup Screen Liar B sau i la i dai i a ete 11 Figure 12 N2KView Window with Tabs Dieplave nenea eee 12 Figure 13 Configuration Dialog E 13 Figure 14 N2KView Window with Tabs Dieplave 14 Figure 15 Connections Settings Dialog ci coca a aa oC Gian a DD bilan avin Dl Cal a la a 15 Page Revision 1 0 Maretron 1 General 1 1 Introduction Congratulations on your purchase of the Maretron DSM800 Vessel Monitoring and Control Indoor Display Maretron has designed and built your display to the
6. Maretron DSM800 Vessel Monitoring and Control Indoor Display User s Manual Revision 1 0 Copyright O 2011 Maretron LLP All Rights Reserved Maretron LLP 9014 N 23 Ave 10 Phoenix AZ 85021 7850 http www maretron com Maretron Manual Part M003002 Revision 1 0 Page i DSM800 User s Manual Revision History Rev Description 1 0 Original document Pageii Revision 1 0 Maretron Table of Contents INI gt ere eee ere ne ee E ENE 1 ES Ne po is de 1 1 2 Firmware Revision Lae eee 2 13 DSM800 F at reS searoncioenaea boa e na a nt a en a i ie e i 2 1 4 DSM800 AccessS ri s ee 2 1 5 Eege 2 2 MEAN eee na anca ani Lao iati De o 3 2 1 Unpacking the BOK Luster nu la ema e ile d ee i aaa a 3 2 2 Choosing a Mounting Location nana 3 23 Mounting the DSM E 3 2 3 1 E Mounting un 3 202 Panel Mo EE 5 2 3 3 Arm Mounting Vase iai aa cians ie pide aia lia iii iti 7 2 4 Connecting the DSM80O0 sasea oaza ie aia avi PU a i date dau tit 8 241 LAN MUR oct ului ilie ala ina ti aia a anii 9 242 USB Device Connection ii ii a a i die 10 2 4 3 Power COMME CHON oi ini nn n mn o nea it on on pe oa ev tara a a pet ni net 10 2 4 4 Power Sequencing ENEE 11 25 Configuring KN 11 2 5 1 Manually Entering LAN Connection Information men nn 12 2 5 2 Entering N2KServer or IPG100 Connection Information mce cecene eee 14 3 Operating the DSM800 noa e ireal m a ne e n a i afet a a 17 3
7. Opening the DSM800 will expose the sensitive electronic components to adverse environmental conditions that may render the unit inoperative Please do not open the DSM800 as this will automatically void the warranty If service is required please return the unit to an authorized Maretron service location Revision 1 0 Page 19 DSM800 User s Manual 6 Technical Specifications Specifications Parameter Value Comment Display Size 8 LED Backlit LCD with Resistive Touch Screen Display Resolution 800x600 Pixel count Display Brightness 300cd m Contrast Ratio 400 1 LCD Color 262K Viewing Angle 130 H 120 V Backlight MTBF 30 000 hours USB Ports Two USB 2 0 Ethernet Ports One RJ 45 GbE For connection to Maretron IPG100 and or router Audio Connection One Speaker Output Approvals Parameter Comment FCC CE CB CCC Electrical Parameter Value Comment Operating Voltage 10 14 Volts DC Voltage 9 30 VDC with optional DC DC adapter Power Consumption Maximum 25 Watts Mechanical Parameter Value Comment Overall Dimensions DxWxH 1 69 x 9 21 x 6 97 43mm x 234mm x 177mm Weight 1 76 Ibs 8kg Front Panel Material ABS Plastic Mounting Wall Rack Stand ARM VESA 75mm x 75mm Environmental Parameter Value Operating Temperature 10 C to 50 C Storage Temperature 10 C to 60 C Page 20 Revisio
8. aintenance is important to ensure continued proper operation of the Maretron DSM800 Perform the following tasks periodically e Clean the unit with a soft cloth Do not use chemical cleaners as they may remove paint or markings or may corrode the DSM800 enclosure or seals Do not use any cleaners containing acetone as they will deteriorate the plastic enclosure Do not spray cleaning liquids directly onto the DSM800 e Ensure that the unit is mounted securely and cannot be moved relative to the mounting surface If the unit is loose tighten the mounting screws e Check the security of the power and network cables connected to the DSM800 and tighten if necessary Page 18 Revision 1 0 Maretron 5 Troubleshooting If you notice unexpected operation of the Maretron DSM800 follow the troubleshooting procedures in this section to remedy simple problems No activity on the display Check the connection to the power and network connectors and tighten if necessary Ensure that power is supplied to the connected power cable Press the power switch located on the underside of the device on the right hand side of the unit behind the LCD screen Other Issues Please refer to the Troubleshooting section of the N2KView User s Manual If these steps do not solve your problem please contact Maretron Technical Support refer to Section 7 for contact information Warning There are no user serviceable components inside the Maretron DSM800
9. dividual sections for additional details e Unpacking the Box Section 2 1 Choosing a Mounting Location Section 2 2 Mounting the DSM800 Section 2 3 Connecting the DSM800 Section 2 4 Configuring the DSM800 Section 2 5 Page 2 Revision 1 0 Maretron 2 Installation 2 1 Unpacking the Box When unpacking the box containing the Maretron DSM800 you should find the following items e 1 DSM800 Vessel Monitoring and Control Indoor Display 1 63000 FSP0481AC101C RS AC Power Adapter 1 32000 000002 RS AC Power Cord 1 12VDC Pigtail 90 Connector 1 44013 030041 RS Screw Kit 1 XTR103 0002 RS Touch Pen 1 DSM800 User s Manual 1 N2KView Documentation CD ROM 1 Warranty Registration Card If any of these items are missing or damaged please contact Maretron 2 2 Choosing a Mounting Location The DSM800 front panel is splash proof IEC IP64 rating protected against the effects of splashed water Although the front panel is splash proof the display panel is intended for indoor use only it is not day light or sun light readable so the DSM800 should be mounted in an indoor location 2 3 Mounting the DSM800 The DSM800 has three mounting options which include e wall mounting if access to the backside of the mounting surface is not available requires purchase of MAFLWK 12 wall mounting Kit accessory e panel mounting requires purchase of optional MAFLPK 12 Panel Mounting Kit accessory e a
10. e connectors e 1x12 V DC Power input connector 1 x Audio line out jack 1 x Power switch 1 x Reset button 1 x RJ 45 Gigabit Ethernet LAN port 2 x USB 2 0 connectors The external I O interface connector panel is shown in Figure 8 Page 8 Revision 1 0 Maretron 12V DC power input Audio line out Power switch RJ45 USB Reset button Figure 8 DSM800 Interface Connector Panel 2 4 1 LAN Connection There is one external RJ 45 LAN connector The RJ 45 connector enables connection to an external network To connect a LAN cable with an RJ 45 connector please follow the instructions below Step 1 Locate the RJ 45 connector on the bottom panel of the DSM800 Series Step 2 Align the connector Align the RJ 45 connector on the LAN cable with the RJ 45 connector on the bottom panel of the DSM800 See Figure 9 Step 3 Insert the LAN cable RJ 45 connector Once aligned gently insert the LAN cable RJ 45 connector into the onboard RJ 45 connector Figure 9 LAN Connection Revision 1 0 Page 9 DSM800 User s Manual 2 4 2 USB Device Connection There are two external USB 2 0 connectors To connect a USB 2 0 or USB 1 1 device please follow the instructions below Step 1 Locate the USB connectors The locations of the USB connectors are shown in Figure 8 Step 2 Align the connectors Align the USB device connector with one of the connectors on the bottom panel See Figure 10 Step 3 Insert the device connector Once al
11. g Internet Protocol IP cameras for viewing within the N2KView software DSMg00 Optional Ethernet USB Keyboard g Or Mouse KS Maretron as IPG100 NMEA 2000 Engine Network Monitor Battery Monitor Electrical Panel Tank Monitor Figure 1 DSM800 Network Diagram Revision 1 0 Page 1 DSM800 User s Manual The Maretron DSM800 is designed to operate within the harsh demands of the marine environment However no piece of marine electronic equipment can function properly unless installed configured and maintained in the correct manner Please read carefully and follow these instructions for installation configuration and usage of the Maretron DSM800 in order to ensure optimal performance 1 2 Firmware Revision This manual corresponds to the DSM800 running N2KView Version 3 2 1 3 DSM800 Features The Maretron DSM800 has the following features e 8 LED Backlit LCD Panel with Resistive Touch Screen 800 x 600 Pixels 300 nits of brightness Solid State Disk Drive Fanless cooling system USB Ports for connecting Keyboards and Mice Ethernet Port for Receiving Networked Data and Video 1 4 DSM800 Accessories Maretron offers the following accessories for the DSM800 e MAFLPK 12 Panel Mounting Kit e MAFLWK 12 Wall Mounting Kit e DC DC 01 60 W DC DC 9 30 VDC input power adapter 1 5 Quick Install Installing the Maretron DSM800 display involves the following five steps Please refer to the in
12. h located on the back panel see Figure 8 to turn the DSM800 on or off If the DSM800 is turned on then the LED found on the front panel will be illuminated blue If the power switch is pushed to power down the DSM800 the LED will be illuminated yellow The DSM800 can also be switched on and off by applying or removing power through an external switch or breaker Anytime the power is reapplied to the DSM800 it will turn on 2 5 Configuring the DSM800 In order to use the DSM800 you must already have N2KServer installed and running on either a Windows PC or on a Maretron IPG100 Internet Protocol Gateway You must also have some information as to the configuration of your local area network The DSM800 will start up with the following warning screen E Warning Maretron N2KView Vessel Monitoring and Control System Software Version 3 2 20110111 WARNING By pressing Accept you acknowledge that while Maretron products are designed to be accurate and reliable they should be used only as aids to navigation and vessel monitoring and not as a replacement for traditional aids and techniques Exit Enter Demo Mode Accept N eae Figure 11 DSM800 Startup Screen You are required to press Accept and thereby acknowledge this warning message before N2KView will run in Live Mode Alternatively you may Enter Demo Mode In Demo Mode you will not be able to connect to a Server and view live data instead simulated da
13. igned gently insert the USB device connector into the onboard connector Figure 10 USB Device Connection 2 4 3 Power Connection The DSM800 can be connected to a power source in one of three ways over current protection should be provided and should be sized in accordance with ABYC E 11 AC and DC ELECTRICAL SYSTEMS ON BOATS 1 Directly with 10 14VDC power source using the 12VDC pigtail 90 connector supplied in the box a Connect the wire with writing along the entire length to the negative supply b Connect the wire with the white dash along the entire length to the positive supply c Plug the 90 connector into the DSM800 s 12VDC power input connector 2 Indirectly with 100 240VAC 50 60Hz power source using the AC power adapter and the AC power cord supplied in the box a Connect the AC power cord to the AC power adapter b Connect the AC power cord to the AC power outlet c Connect the 12VDC connector from the AC power adapter to the DSM800 s 12VDC power input connector 3 Directly with a 9 32VDC power source using the optional DC DC power adapter Maretron Part No DC DC 01 a Connect the 9 32VDC input wires of the DC DC power adapter to the 9 32VDC supply b Connect the 12VDC output connector from the DC DC power adapter to the DSM800 s 12VDC power input connector Page 10 Revision 1 0 Maretron 2 4 4 Power Sequencing When the DSM800 is connected to an appropriate power source you can use the power switc
14. n 1 0 Maretron 7 Technical Support If you require technical support for Maretron products you can reach us in any of the following ways Telephone 1 866 550 9100 Fax 1 602 861 1777 E mail support maretron com World Wide Web http Awww maretron com Mail Maretron LLP Attn Technical Support 9014 N 23 Ave Suite 10 Phoenix AZ 85021 USA Revision 1 0 Page 21 DSM800 User s Manual 8 Maretron 1 Year Limited Warranty Maretron warrants the DSM800 to be free from defects in materials and workmanship for one 1 year from the date of original purchase If within the applicable period any such products shall be proved to Maretron s satisfaction to fail to meet the above limited warranty such products shall be repaired or replaced at Maretron s option Purchaser s exclusive remedy and Maretron s sole obligation hereunder provided product is returned pursuant to the return requirements below shall be limited to the repair or replacement at Maretron s option of any product not meeting the above limited warranty and which is returned to Maretron or if Maretron is unable to deliver a replacement that is free from defects in materials or workmanship Purchaser s payment for such product will be refunded Maretron assumes no liability whatsoever for expenses of removing any defective product or part or for installing the repaired product or part or a replacement therefore or for any loss or damage to equipment in
15. nks Pair Bluetooth Device Calibrate Touch Screen Close Figure 13 Configuration Dialog C Uncheck the Use DHCP box to indicate that your LAN does not use DHCP d In the IP Address field enter the IP address you wish to assign to the DSM800 e In the Netmask field enter the netmask value used on your LAN in most cases this value will be 255 255 255 0 f In the Gateway field enter the IP address of the default gateway of your LAN g In the Name Server field enter the IP address of a DNS Dynamic Name Service Server used on your LAN h Click the Update button to make these changes permanent The screen will go blank for a few seconds while this is being done Revision 1 0 Page 13 DSM800 User s Manual 2 5 2 Entering N2KServer or IPG100 Connection Information Once the DSM800 has been properly configured to connect to your LAN you must configure the connection to enable the DSM800 to receive information from an instance of N2KServer or an IPG100 Server This is done through the following steps A Tachometer wm JG e d z i Ce Cie It Pi Screens Setup gt o e C 404 Vi 4 rpm a NG psi Engine Load Alternator Voltage pr Oil Ten f I A fe A f AN m ed BA IK aa N e ae e 2 Alerts Setup D Cameras Setup A8 b LE Var ar 15 0 7 NA 176 E er KZ ol E e os GA KZ Fuel Rat Fuel P
16. panel Figure 6 Page 6 Revision 1 0 Maretron Panel Screen Clamp mm i Figure 6 Tighten the Panel Mounting Clamp Screws 2 3 3 Arm Mounting NOTE When purchasing a mounting arm please ensure that it is VESA compliant and that the arm has a 75 mm interface pad If it is not VESA compliant it cannot be used to support the DSM800 The DSM800 is VESA Video Electronics Standards Association compliant and can be mounted on an arm with a 75mm interface pad To mount the DSM800 on an arm please follow the steps below Step 1 Please correctly mount the arm onto the base surface To do this refer to the installation documentation that came with the mounting arm Step 2 Once the mounting arm has been firmly attached to the base surface lift the DSM800 onto the interface pad of the mounting arm Step 3 Align the retention screw holes on the mounting arm interface with those in the DSM800 The arm mount retention screw holes are shown in Figure 7 Step 4 Secure the DSM800 to the interface pad by inserting the retention screws through the bottom of the mounting arm interface pad and into the DSM800 Revision 1 0 Page 7 DSM800 User s Manual VESA mount screw holes Figure 7 DSM800 Arm Mounting Retention Screw Holes 2 4 Connecting the DSM800 All I O interface connections of the DSM800 are found on the bottom panel The UO interface panel located on the bottom of the DSM800 has the following I O interfac
17. ressure u e RK Level Password Configuration R IN j gal US hour Figure 14 N2KView Window with Tabs Displayed a Click anywhere inside the N2KView screen to display the screen tabs as shown in Figure 14 above b Click on the Connections tab on the right side of the N2KView screen to display the Connections Settings dialog Page 14 Revision 1 0 Maretron Connections Settings N2KServer Connection Hostname IP Address 10 0 0 77 Password Features Requested Basic Platinum Connection State Disconnected IPG100 found at 10 0 0 91 IPG100 found at 10 0 0 77 Disconnect Connect Email Connection Mail Server Name Mail Account User Name Password From Email Address Default Email Address Figure 15 Connections Settings Dialog Ensure that N2KView is not connected to a N2KServer by pressing the Disconnect button While N2KView is connected you are not able to edit fields In the Hostname IP Address text box enter the IP address of the computer or IPG100 running N2KServer If your DSM800 configuration has been programmed to match your LAN the left side of the N2KServer Connection window will display the address of any N2KServer running on a PC or IPG100 s found on the LAN Leave the Port setting at the initial value of 6544 unless the router between N2KView and N2KServer has been set up to do port translation In
18. rm mounting requires purchase of a VESA 75mm mounting arm Maretron suggests a location at which the display can be viewed from a relatively straight angle 2 3 1 Wall Mounting To mount the DSM800 using the optional wall mounting kit Maretron part number MAFLWK 12 please follow the steps below Step 1 Select the location on the wall for the wall mounting bracket Step 2 Carefully mark the locations of the four screw holes in the bracket on the wall Step 3 Drill four pilot holes at the marked locations on the wall for the bracket retention screws Step 4 Align the wall mounting bracket screw holes with the pilot holes Revision 1 0 Page 3 DSM800 User s Manual Step 5 Secure the mounting bracket to the wall by inserting the retention screws into the four pilot holes and tightening them see Figure 2 3 3 y Figure 2 Wall Mounting Bracket Step 6 Insert the four monitor mounting screws provided in the wall mounting kit into the four screw holes on the rear panel of the DSM800 and tighten until the screw shank is secured against the rear panel Figure 3 Step 7 Align the mounting screws on the monitor rear panel with the mounting holes on the bracket Step 8 Carefully insert the screws through the holes and gently pull the monitor downwards until the monitor rests securely in the slotted holes Figure 3 Ensure that all four of the mounting screws fit snugly into their respective slotted holes Figure 3
19. ta will be provided to stimulate the controls Revision 1 0 Page 11 DSM800 User s Manual The first time you start the DSM800 you must ensure that the device can connect to your LAN local area network The DSM800 comes from the factory preconfigured to obtain its LAN connection information from a DHCP Dynamic Host Control Protocol server If your local area network uses a DHCP server no configuration is necessary and the DSM800 should be able to successfully connect to the local area network 2 5 1 Manually Entering LAN Connection Information If your local area network does not use DHCP you must manually enter the LAN connection information into the DSM800 This is done through the following steps Alerts Engines DC Systems Tachometer ma a Xe NE Noss on Load Screens Setup oe gt p Alerts Setup Fuel Pressure Fuel Rate Cameras Setup KO Water In Fuel galusyhour 17 galUSyhour Figure 12 N2KView Window with Tabs Displayed a Click anywhere inside the N2KView screen to display the screen tabs as shown in Figure 12 above b Click on the Configuration tab on the right side of the N2KView screen to display the Configuration dialog Page 12 Revision 1 0 Configuration x Configuration Label Filename Network Configuration Use DHCP gene NOK View Gateway Name Server Screen Configuration BM Enable Screen Blanking Delay Before Screen Bla
20. the Password text box enter the same server password that you entered into the N2KServer Service Manager for N2KServer running on a PC or programmed into the IPG100 If you have purchased the Platinum Edition of N2KView and wish to use all of the Platinum Edition features select Platinum from Features Requested If you have purchased the Basic Edition of N2KView or you wish to use only the BasicEdition subset of features of N2KView leaving the Platinum Edition features available for another copy of N2KView select Basic from Features Requested Click Connect The Connection State part of the window will blink Connecting for a few seconds It will then either display Connected if the connection was successfully made or display a message indicating that the connection was not made and suggesting further action to take Revision 1 0 Page 15 DSM800 User s Manual If no data is displayed please check the following 1 Make sure the Server Password entered in N2KView matches the Server Password entered into the N2KServer Service Manager on the computer running N2KServer or the IPG100 as appropriate If the server is running on an IPG100 the password in the IPG100 is set from a DSM250 or N2KAnalyzer 2 Make sure the Server Address matches the IP address of the computer or IPG100 running N2KServer 3 Make sure you have appropriate instrumen
21. ts on the NMEA 2000 network to provide the data you are trying to view on the N2KView screen To test the network connection between N2KView and the N2KServer you may wish to run N2KServer in Simulated Data mode 4 Make sure that the instances that are being monitored correspond to the instances being transmitted You can set the instance number of the component to Any to make sure that there is any data of that type on the bus Page 16 Revision 1 0 Maretron 3 Operating the DSM800 3 1 Turning the DSM800 On To turn on the DSM800 when the front panel LED is illuminated yellow press the power rocker switch located underneath the DSM800 on the right hand side of the unit behind the LCD screen To turn on the DSM800 when the front panel LED is not illuminated turn on the power from the external breaker or switch 3 2 Turning the DSM800 Off To turn the DSM800 off use the Shutdown administrative tab of the N2KView software Alternatively you can power down the unit by pressing the DSM800 s power rocker switch Lastly you can power down the unit by turning of the power source with an external breaker or external switch 3 3 Using the DSM800 The DSM800 runs a fully functional version of the Maretron N2KView software Please refer to the N2KView User s Manual included with the DSM800 for detailed operating instructions Revision 1 0 Page 17 DSM800 User s Manual 4 Maintenance Regular m
22. uiring expedited shipping i e overnight shipments Failure to follow this warranty return procedure could result in the product s warranty becoming null and void Maretron reserves the right to modify or replace at its sole discretion without prior notification the warranty listed above To obtain a copy of the then current warranty policy please go to the following web page http Awww maretron com company warranty php Revision 1 0 Page 23
Download Pdf Manuals
Related Search