brita pegler triflow 110107
Contents
1. consistent flow Supplies should be from a common source either mains or tank fed but if supplies are not equal pressures then non return valves should be fitted not supplied To achieve this please order Pegler Prestex 802 check valve order reference code 551001 15mm It is also both Pegler and BRITA s recommendation and good plumbing practice that a service valve should also be installed in both the inlet supply lines upstream of the product for ease of any future maintenance To satisfy this requirement and that stated above then we recommend you fit Pegler Prestex 8028 combined double check valve and service valve order reference code 551020 15mm The installation of all parts of the tap has to be done according country specific directives for installation of drinking water devices The tap used in combination with the water filter tap must be free of limescale build up It is not permitted to use a water softener before the filter The 3 Way Titanium and 3 Way Rosedale models have been designed to function under the following conditions Transport Ambient temperature operation storage transport 1 60 C Minimum supply pressure on cold side 1 0 bar cartridge optimum pressure 1 5bar Maximum supply pressure on cold side 6 0 bar Minimum supply pressure on hot side 0 1 bar Maximum supply pressure on hot side 6 0 bar To gain best performance from the BRITA filter cartridge please ensure that the cartridge is not exposed to te2. pressure may incur dripping for longer periods of time brita pegler triflow 110107 11 1 07 14 2 Page 4 Pre installation Checks 1 Ensure that there is sufficient space to install the product without it hampering its operation When fitting in a corner position make sure there is sufficient clearance for the use of the handles and the movement on the spout 2 Ensure that the outlet will protrude sufficiently into the sink s and will clear any obstructions 3 When installing the product the hot inlet should be on the left hand side and the cold on the right hand side and the filter handle facing the front INSTALLATION For both Titanium and Rosedale Kitchen Filter taps 1 Decide location of the cartridge this should be located with a suitable distance from the tap hole BRITA and PEGLER recommend no more than 0 75meters At this point do not assemble the cartridge to the cartridge head Please note It may be noted that surplus tube may be noticeable depending on the cartridge location Neither PEGLER nor BRITA advise that this tube is cut due to exacting requirements of the cut finish Likewise the surplus tube can be used to fix around the internal wall of the cupboard if required to ensure free space within 2 Turn off the water supply And drain down system 3 Remove the old kitchen tap by disconnecting any flexible hoses or copper tails from the domestic supply Unscrew any clamping nuts and screws from the underside of the
3. tap 4 Once old tap is removed clean around the sink tap hole and ensure it s clean from dirt and debris 5 Screw the first flexible hose into body of the tap and tighten up ensuring O ring seal is firmly in place to prevent any leaks 6 The product comes with ease of installation push fit connectors Push in loose plastic tube not identified with tag into push fit connector mounted in base of tap body Push home until stop is achieved IMPORTANT NOTE In any event of installing a plastic hose into the incorrect push fit connection to remove press the release collar around the push fit and pull out hose oe brita pegler triflow 110107 11 1 07 14 2 Page 5 7 Locate and screw in clamping stud until stop is achieved 8 Seperately push in lifetime indicator cable into base flange ensuring O ring is located in place with in the base flange hole 9 Ensure the rubber seal is in position in the separate base flange and locate roughly over the hole in the ware 10 Feed indicator light cable through the hole in ware and decide orientation of indicator light IMPORTANT NOTE Deciding on the angle of the indicator light now will make installation easier later Take care not to pull or damage the indicator light cable 11 Position the tap onto base flange in desired position Ensure all parts are located through the flange including the threaded clamping stud single stainless steel flexible hose and t
4. to BRITA will be recycled Please send to FREEPOST RLZS YGLS ZLGL BRITA COALVILLE LE67 1TE Cartridge Distributor Brita Water Filter Systems Ltd Brita House 9 Granville Way Chaucer Industrial Estate Bicester Oxfordshire OX26 4JT United Kingdom For information on BRITA and cartridge queries please contact BRITA customer care Telephone 0845 0770 035 brita pegler triflow 110107 11 1 07 14 2 Page 12 Maximum drilled hole size 048 Optimum drilled hole size 044 1 3 4 dia Minimum drilled hole size 33 All dimensions in mm Version 2 Nov 06
5. ation WHO guidelines for drinking water quality IMPORTANT NOTE For people with kidney disease or dialysis patients During the filtering process there may be a slight increase in potassium content If you have kidney disease and or have to live according to a potassium regulated diet we recommend that you discuss the use of the filter with your doctor If you have kidney disease and or have to live according to a potassium regulated diet we recommend that you call Brita Care Customer Services on 0044 0 870 487 1000 for further information which you may wish to discuss with your doctor If your BRITA System is not in use for several days 1 2 days we recommend that you flush the filter system with at least 1 2 litres BRITA recommends that the filter system not be taken out of use for longer periods After stagnation times of over 4 weeks the filter should be flushed with 6 0 litres or alternatively replaced In this connection please also remember the maximum useful life of the filter cartridge of 3 months Explanation of BRITA filter cartridge Serial No Example of the batch code 5154 First digit 5 year of production 2005 Second and third digit 15 calendar week No 15 Fourth digit 4 4th day of the week 4 Thursday The BRITA filter must be thoroughly flushed until water runs completely clear The filter cartridge should be changed after 500 litres but latest 3 months after commissioning regardless of the level
6. brita pegler triflow 110107 11 1 07 14 2 Page 1 ia t Your Guide to the Installation Care and Maintenance of BRITA FRANCIS PEGLER 3 Way Titanium and 3 Way Rosedale Pegler BRITA Water Filter Systems Ltd Pegler Limited BRITA House St Catherine s Avenue 9 Granville Way Doncaster South Yorkshire Bicester 0X26 4JT DN4 8DF www BRITA co uk www pegler co uk brita pegler triflow 110107 11 1 07 14 2 Page 2 Water regulations requirements It is important to ensure that the water supplies to your taps and mixers are connected in accordance with the water regulations WRAS requirements and good plumbing practice Please note The production of all component parts on both tap and cartridge have been manufactured using appropriate materials and as such all appropriate parts in contact with potable water have been given full WRAS approval Contact either Pegler or BRITA for the official WRAS approval number Please note it is a water regulation requirement to fit double check valves on the inlets of your current kitchen tap especially if the water is single flow and therefore mixes within the spout or body of the tap The 3 Way Titanium and the 3 Way Rosedale are single flow taps and for installation in line with those regulations it is both BRITA and Pegler s recommendation and good plumbing practice that the supplies of hot and cold water to the sink mixer should be at equal balanced pressures in order to provide a
7. he two plastic hoses all fit through hole in the base flange us 12 Once loosely in place check again that handle and spout movement is not obstructed es brita pegler triflow 110107 11 1 07 14 2 Page 6 13 After loosely mounting in place offer the second flexible hose up through the ware into the 3 Way tap and tighten up ensuring O ring seal is firmly in place to prevent any leaks 14 To tighten the mixer to the ware firstly place horse shoe shaped clamping plate onto the threaded clamping stud ensure larger diameter is positioned under sink Then secure by screwing tight the clamping nut taking care of indicator light cable as this is now hanging down from tap 15 Once again re check that handle and spout movement is not obstructed before tightening fully home Please note The operation of the valves and the handles is such that they are precise and easy to operate Total movement from fully on to fully off is only 90 or quarter of a turn Excessive force once opened or closed may force the valve to malfunction 16 The cartridge head has already been semi assembled with brass check valve elbow in place on the inlet of the cartridge head and a plastic connection piece on the outlet of the cartridge head These have both been assembled to a defined torque and therefore should not be removed by anyone other than a BRITA or PEGLER approved installation engineer 17 Screw the head bracket and the cartridge
8. head screws are provided for the bracket assembly then screw the cartridge to the cartridge head after removing the yellow plastic protection cap This simply pulls away oe brita pegler triflow 110107 11 1 07 14 2 Page 7 18 Once assembled offer under the sink usually in a kitchen cupboards the cartridge to find its best location ensuring allowance is made for the pre assembled electronic box Likewise be aware that to replace the cartridge you have to unscrew so sufficient room below the cartridge is required for removal Note the cartridge can be located in a vertical or horizontal manner 19 Once its location is identified remove the cartridge and mark the location of the holes from the bracket on the internal wall of the cupboard This will help with the assembly of the bracket onto the wall 20 Screw the bracket in place 21 Re assemble the cartridge back into the cartridge head 22 Take the hose identified with a tag and simply push into the outlet end of the cartridge head until stop is achieved The remaining plastic hose should then be pushed into the brass check valve elbow until the stop is achieved 23 Once completed push in the connecting plug on the end of the lifetime indicator cable into the socket on the side of the electronic box Remove the battery clip and insert the battery supplied loose ref CR2032 using the indication on the battery carrier for confirmation of the correct installation of the batter
9. id green light e When the filter condition is considered to be at 90 of its life then the light will turn amber When the life of the filter has been exhausted then it will turn red When the battery voltage has dropped to a low level it is indicated by a red flash Solid Green filter OK Solid Amber filter past 90 of usable life Sold Red filter needs changing Red flashes battery need replacing It is recommended that the batteries should be changed every twelve months to reduce the risk of battery leakage When a new filter is fitted pressing the reset button restarts the lifetime indicator Changing the battery will not affect the filter state counters oe brita pegler triflow 110107 11 1 07 14 2 Page 9 CARE AND MAINTENANCE To maintain the surface finishes simply wipe occasionally with a mild detergent on soft damp cloth dry using soft cloth never use abrasive cleaners or chemical household cleaners avoid contact with concentrated bleach PEGLER products are manufactured to the highest standards and should require little or no maintenance In the unlikely event of any spare part requirements please contact your nearest stockist or Pegler Technical Helpline Telephone 0870 1200 285 Fax 01302 560537 Cartridge Exchange Instructions Water filter tap cartridge The filter cartridge should be exchanged after 500 litres or after 3 months whichever occurs first to ensure optimum filter performance 1 Whe
10. mperatures below 4 C or in excess of 30 C Average filter capacity is based on 500 litres or 3 months average usage A design tested non return valve pursuant to DIN 3269 1 DIN 3269 2 DVGW and SVGW has been factory fitted at the water inlet of the connecting fitting The BRITA Filter must only be connected to a potable cold water supply Do not use a BRITA Filter where water is microbiologically unsafe or with waters of unknown quality without appropriate sterilisation If an instruction is received from the authorities that mains water must be boiled the BRITA filtered water must also be boiled When the instruction to boil water is no longer in force a new filter cartridge must be inserted and the connections must be cleaned For certain groups of people e g those with impaired immunity and for babies it is generally recommended that tap water should be boiled this also applies to filtered water Irrespective of the water used you should use utensils with stainless steel such as kettles and saucepans to boil the water In particular people who are sensitive to nickel should use appliances made of stainless steel or kettles with concealed elements oe brita pegler triflow 110107 11 1 07 14 2 Page 3 For reasons of hygiene the filter is given a special treatment with silver A small amount of silver which poses no known threat to health may be transferred to the water This transference would be within the World Health Organis
11. n cartridge exchange indicator gives signal filter cartridge needs to be exchanged Please see sequence of indicator within user manual supplied with the initial tap Red light to indicate filter ae exchange 2 Remove exhausted cartridge by unscrewing clockwise from the filter head 3 Remove plug from the top of the new filter cartridge 4 Insert new filter cartridge into filter head and turn anti clockwise until in place Do not over tighten oe brita pegler triflow 110107 11 1 07 14 2 Page 10 5 Restart the cartridge exchange indicator by pressing the Reset button located on the battery housing 6 Turn on the filtered water and flush water through the cartridge for approximately 1 minute 3 litres or until water runs completely clear Turn handle to operate BRITA filter water 7 Check the tap to see that the cartridge exchange indicator has turned to solid green Please see Special Guidelines for lifetime indicator If not please repeat step 5 oe brita pegler triflow 110107 11 1 07 14 2 Page 11 8 Please note date of exchange into your booklet of maintenance below Cartridge Exchange Date he seeceeeeeeeeeeeeeeeeeeeeeeeeaes Note Exhausted filter cartridges can be disposed of in accordance with the local laws and regulations in principle normal domestic waste In addition please note that all BRITA components have been manufactured from recyclable materials Any cartridges returned
12. of exhaustion To ensure optimum filter performance the electronic exchange indicator integrated in your tap tells you when to change the cartridge Filter head of the filter system is designed for a service life of 5 years and bear a production date Exchange must be carried out after 5 years by an expert Please store cartridge always in original sealed foil at a cool and dry place Although every effort is made to ensure good tasting reliable odour free water BRITA cannot offer guaranteed improvement on water quality if the intake of water is microbiologically unsafe or of unknown quality without adequate disinfection before entering the cartridge unit An independent institute has also certified the food grade quality of BRITA water and filter products A copy of this is available upon request Should excessive flow be experienced then it may be necessary to install a Pressure reducing valve upstream from the product Please order Pegler Prestex PRV 2 order reference code 5A2011 15mm which will reduce inlet pressure to 1 5bar minimum Please note The 3 Way Titanium and 3 Way Rosedale will for a short period after use drip this is to allow water pressure within the spout to reduce to atmospheric conditions and remove any pressure from the filter and filter head It has been deemed that the amount of dripping after use is acceptable at the 1 5 bar optimum operating pressure Installations made above this recommendation operating
13. y oe brita pegler triflow 110107 11 1 07 14 2 Page 8 24 Connect inlets to supplies using a appropriate connectors or please order PEGLER Prestex 40 straight coupling order reference code 709017 15mm X 15mm Please note Please ensure that filter water is always connected via the cold supply line In normal installation types hot is on the left and cold is on the right when viewed from the front 25 Turn on water supply and check for leaks before the handles are turned on 26 Next turn on the individual tap handles and check for further any addition leaks Please note The filter water is dispensed via the front handle identified with the BRITA logo 27 Press the reset button and hold for 2 seconds and with immediate effect the lifetime indicator light in the flange tap should be seen solid red and then green YOU HAVE NOW STARTED THE LIFETIME INDICATOR FOR IMMEDIATE USE 28 For immediate use of the filtered water simply run for a minute approx 3 litres or until water runs clear This is purely to activate the filter material within each cartridge for perfect BRITA filter water Please note This simply running on for a minute approx 3 litres or until water runs clear needs to be done at the point of use for each new cartridge Special Guidelines for lifetime indicator The lifetime indicator is to function only when the tap is delivering BRITA filtered water e When the filter and battery are OK there will be a sol
Download Pdf Manuals
Related Search