8pc Truck Bed LED Lighting Kit
Contents
1. 10 11 INSTALLATION INSTRUCTIONS Tech Support 896 768 5700 EXT 2 TechSupport LeDGlow com y W d W A _ n a Attach the wire that you just connected to the positive 12 volt source to the right post on the on off switch using the supplied female spade connector Connect both power wires with the white stripe to the center post on the on off switch using the supplied female spade connector Note If you want to use an existing or different switch than the one provided be sure to verify the switch is rated for 12 volts and follow specific instructions for the switch Route both solid black ground wires to the left post brass pin on the on off switch B rass Kit lt Run Additional Ground 12 Volt Power Source Power From Kit Attach a ground wire to a ground source and connect this wire to both of the kit s ground wires Connect them all to the left post brass pin on the on off switch using the supplied spade connector This will provide illumination to the switch when turned on Secure all the excess wire with zip ties Once the Truck Bed Lighting Kit is installed and powered ensure all of the lights are functioning properly INSTALLATION INSTROCTIONS L GLOW Tech Support 856 768 5700 EXT 2 DOD TechSupport LEDGlow com ONE YEAR NON TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER LEDGlow Lighting LLC LEDGlow warrants to the original retail consumer purchaser and n2. for customers in the contiguous United States LEDGlow will pay the shipping charges if any Product fails during the first thirty 30 days after purchase The Product must be returned in its original carton or in a similar package affording an equal degree of protection LEDGlow will return the repaired or replaced Product freight prepaid to the Purchaser LEDGlow does not provide Purchasers with temporary replacement units during the warranty period or at any other time This limited warranty is non transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle on which the Product is installed An original retail consumer purchaser is a person who originally purchases the Product or a gift recipient of a new Product that is in its original packaging and unopened This limited warranty is subject to all of the following terms and conditions TERMS AND CONDITIONS 1 NOTIFICATION OF CLAIMS WARRANTY SERVICE IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR WORKMANSHIP WRITTEN NOTICE WITH AN EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW ALL WARRANTY CLAIMS MUST BE MADE WITHIN THE WARRANTY PERIOD AND ANY PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN ACCORDANCE WITH LEDGLOW S PROCEDURES INCLUDING USE OF RMA NUMBERS SUPPLIED BY LEDGLOW AFTER NOTIFICATION THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND T
3. ES FROM WARRANTY COVERAGE PRODUCTS SOLD AS IS AND OR WITH ALL FAULTS LEDGLOW ALSO EXCLUDES FROM WARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS FUSES AND BATTERIES All software and accompanying documentation furnished with or as part of the Product is furnished AS IS 1 e without any warranty of any kind except where expressly provided otherwise in any documentation or license agreement furnished with the Product 4 PROOF OF PURCHASE REGISTRATION The Purchaser s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility Registration of any Product or of this limited warranty is voluntary and failure to register will not diminish any rights available under this warranty DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2 312 3 OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE LIMITATION OF LIABILITY THE LIABILITY OF LEDGLOW IF ANY AND PURCHASER S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH SUCH CLAIM IS MADE IN
4. HE ORIGINAL WARRANTY PERIOD THE SPECIFIC WARRANTY ON THE REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY 90 DAYS FOLLOWING THE REPAIR OR REPLACEMENT OF THAT PART OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY WHICHEVER IS GREATER 2 EXCLUSIVE REMEDY ACCEPTANCE PURCHASER S EXCLUSIVE REMEDY AND LEDGLOW S SOLE OBLIGATION IS TO SUPPLY OR PAY FOR ALL LABOR NECESSARY TO REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW OR REBUILT REPLACEMENTS FOR DEFECTIVE PARTS LEDGLOW WILL REFUND THE PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR OR REPLACEMENT FAILS TO REMEDY THE DEFECT PURCHASER S FAILURE TO MAKE A CLAIM AS PROVIDED IN PARAGRAPH 1 ABOVE OR CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY PURCHASER OF ALL CLAIMS THERETO 3 EXCEPTIONS TO LIMITED WARRANTY LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT THAT IS SUBJECTED TO ANY OF THE FOLLOWING ABUSE IMPROPER USE NEGLIGENCE ACCIDENT MODIFICATION FAILURE TO FOLLOW THE OPERATING PROCEDURES OUTLINED IN THE USER S MANUAL FAILURE TO FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE MANUAL FOR THE PRODUCT ATTEMPTED REPAIR BY NON QUALIFIED PERSONNEL OPERATION OF THE PRODUCT OUTSIDE OF THE PUBLISHED ENVIRONMENTAL AND ELECTRICAL PARAMETERS OR IF THE PRODUCT S ORIGINAL IDENTIFICATION TRADEMARK SERIAL NUMBER MARKINGS HAVE BEEN DEFACED ALTERED OR REMOVED LEDGLOW EXCLUD
5. INSTALLATION INSTROCTIONS L DGLOW estes sMUEKT LOSS OEE TechSuppnort LEDGIoOw com 8pc Truck Bed LED Lighting Kit Warning Please check your state and local laws before installing this Truck Bed Lighting Kit Every state has different policies and procedures in place regarding aftermarket LED lighting accessories LEDGlow is not responsible for any fines that you may receive while using this lighting kit This kit is for off road use only Warning The installation of this kit is recommended to be installed by a licensed professional The improper installation of this kit will void all warranties It is recommended to install each lighting strip using 3M Adhesion Promoter which allows for a much stronger bond between the adhesive tape of the pod light and the cleaned mounting surface of your truck bed PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS TRUCK BED LIGHTING KIT Truck Bed Lighting Kit Includes 2 Strands of 4 Pod Lights 1 On Off Switch 2 Female Spade Connector 16 Screws Truck Bed Lighting Kit Installation 1 Prior to installation clean the proposed mounting areas with soap and water then wipe down with alcohol and allow time to dry 2 Arrange the lights in your truck bed the way you plan on installing them You can refer to the schematic below for the ideal placement of each pod light Be sure there is enough space under the bedrail or tonneau cover to mount eac
6. NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER GOVERNING LAW This non transferrable limited warranty shall be governed by the law of the State of New Jersey U S A and the United States of America excluding their conflicts of laws principles The courts of Camden County New Jersey shall have the exclusive jurisdiction over any legal action with respect to this warranty This limited warranty gives specific legal rights You may also have other rights that may vary from state to state or from country to country Some states or countries do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you You are advised to consult applicable state or country laws for a full determination of rights
7. h pod light If the strand of lights is too long gather the excess wire between the pods and secure them with zip ties Note Do not cut the wires between each pod in order to shorten them This will void ALL warranties 3 Once you have determined the locations where you want to mount each pod you can mount each pod light to the cleaned surface of your bedrail Be sure to press firmly on each pod to ensure it is secured Optional To achieve the strongest bond between the pods and the mounting surface of the bedrail you can use 3M Adhesion Promoter which is sold separately from your kit 4 Route the power wires from both light strands through the truck bed and into your cab using an existing hole with a rubber grommet If you do not have an existing hole in your cab you can drill a new hole to pass the wires through Note If you are drilling a new hole be sure to install a rubber grommet to ensure the metal does not cut the power wires over time 5 Connect the 16 or 18 gauge automotive grade wiring to a positive 12 volt source You can connect the wire to the positive terminal of the battery or at any 12 volt source in the fuse box using LEDGlow s Expandable Circuit which is sold separately from your kit Note Be sure to install a 5 amp inline fuse 5 8 inches from the power supply If you would like the truck bed lights to turn on without your truck being on connect this power wire to a constant 12 volt source L DGLOV
8. ot any other purchaser or subsequent owner that this Product will be free from defects in material or workmanship for a period of one 1 year from the purchase date This warranty does not cover any Product that is 1 installed incorrectly or 2 damaged by collisions vandalism other accidents or similar causes For a period of one 1 year from the date of purchase at no charge to the Purchaser LEDGlow will repair or replace this Product if it is determined by LEDGlow to be defective After the warranty period the Purchaser must pay all charges for parts and labor Coverage under this warranty is only valid within the United States including its territories as well as in certain other countries Purchasers should check our website www LEDGlow com to determine the warranty coverage in the countries in which they are located LEDGlow does not warrant the installation of the Product which is the sole responsibility of the Purchaser Installation should be done by licensed professionals Improper installation may cause damage to the Product and any vehicle in which it is installed and may cause burns and electrical injury to individuals LEDGlow s warranty does not cover any expenses incurred in removing Products that are defective or re installing replacement Products in their place During the warranty period to have the Product repaired or replaced the Purchaser must return the Product freight prepaid by the Purchaser to LEDGlow but
Download Pdf Manuals
Related Search