Home

SBOX-100-QM87i_UMN_v1.00

1. 50 Azalia HD Audio Enabled 52 Serial IRQ Mode Continuous Q J J 52 Power Saving Function ERP Disabled 52 VT d IDISabIed I u __ _ 53 Primary Display AUTO uuu u uuu uuu u u u uuu 54 DVMT Pre Allocated 256N U J J 54 DVMT Total Gfx Mem 256N J J J 55 Primary IGFX Boot Display VBIOS Default 55 Bootup NumLock State Or u J Q J J 57 Quiel Boot Enabled RENTEN 57 Option ROM Messages Force BIOS J U J J Q 57 Launch PXE OpROM Disabled J J T J J 58 UEFTIBool IDISaDIGO uu u uuu uuu u uu u u u uuu uuu uuu Ou D REGN ena 58 Administrator Password LLULLU LLULLU 58 User PassWord
2. SBOX 100 QM87i Fanless Marine Computer 1 5 Technical Specifications The specifications for the SBOX 100 QM87i are listed below SBOX 100 QM87i CPU 22nm 4th generation dual core Intel Core i5 4400E CPU 2 7GHz 3M cache System Chipset Intel QM87 Express Chipset System Memory Two 1600 MHz 2 GB DDR3 SDRAM SO DIMM preinstalled system max 16 GB Two GbE LAN RJ 45 connectors with teaming support and 2 kV isolation protection LAN1 Intel I217 LM with Intel AMT 9 0 support Intel 1210 Ethernet controller CAN Bus 2 x CAN bus 2 0B terminal block 3 pin with 2 5 kV isolation protection Display 1 x DVI D connector 1 x HDMI connector 1 x VGA connector Serial Port 1 x RS 232 DB 9 serial port non isolated 4 x RS 232 422 485 9 serial port 2 5 kV isolation protection 2 x USB 2 0 port 2 x USB 3 0 port 1 x Line in jack 1 x Line out jack 1 x Mic in jack SBOX 100 QM87i Fanless Marine Computer Keyboard Mouse 1 x PS 2 connector Storage 2 x 2 5 SATA 6GB s SSD bay with RAID 0 1 function 1 x External CFast socket with a screwed cover Expansion Slot 1 x Full size PCle Mini slot 1 x Full size Half size PCle Mini slot 1 x IRIS 2400 remote management module slot LED Indicators Power on green off orange HDD CFast active blinking in red IPMI enabled blue disabled off Isolated 18 V 36 V DC 4A max 3 pin ter
3. J J Qux J J Q J J 80 VGA Connector VGA1 Pinouts J J anna anna anna anna 81 HDMI Connector HDMI1 Pinouts J J Q J J 81 RJ 45 GbE Connector LAN1 2 CN1 Pinouts 82 RS 232 Serial Port COM1 Pinouts J J 82 USB 2 0 Connector 0581 Pinouts 82 USB 3 0 Connector USB3_CN1 Pinouts J J 83 A w SBOX 100 QM87i Fanless Marine Computer BIOS Ment T 29 BIOS Menu 2 Advance Ed 30 BIOS Menu 3 ACPI Configuration J J asia J J T aui nra Q J J RR CRUS 31 BIOS Menu 4 RIC Wake Settings 32 BIOS Menu 5 Trusted Computing J cus sues us Cut anna Ca nex E Q T J J 33 BIOS Menu 6 CPU Configuration J eu nnn 34 BIOS
4. 38 Intel AMT Enabled Saa 39 Un Configure Disabled 39 USB DEVICES aykay 40 Legacy USB Support Enabled Lu III 40 MONTON u 41 Serial Port Enabled MUN J mnnn 43 Change S uuu ull l l ll lll l i ll l i i iii N 43 5 8 78 uuu uuu TEM 44 Change III LIL a 44 Serial Port Mode RS485 45 endi 45 Change Settings E a EEE 45 Serial Port Mode RS485 UULULL TT u 46 Serial Port Enabled U 46 Change Selungs lAUEO suec u uuu lll ll lll ll l ll l l il l Renata 46 Serial Port Mode R9485 47 Serial Port Enabled LLL AA IILI LI s 47 Change 47 Serial Port Mode RS485 48 Console Redirection Enabled Ed 49 Auto Recovery Function Disabled
5. 56 BIOS MENU riage cre cere ss su 56 BIOS 22 Sec rily uuu L Iis 58 BIOS 2 59 BIOS Menu 24 Server ManagemoenLt J J U J Q T J J 60 BIOS Menu 25 System Event Log nuu oce 61 BIOS Menu 26 BMC Network Configuration J nennen nana nnns 63 Chapter 1 Introduction Integration Corp SBOX 100 QM87i Fanless Marine Computer 1 1 Overview Figure 1 1 SBOX 100 QM87i Fanless Marine Computer The SBOX 100 QM87i series is a fanless marine computer with Intel Core 15 4400 processor and Intel 87 Express Chipset The SBOX 100 QM87i is preinstalled 4 GB of DDR3 SO DIMM and can accommodate up to 16 GB of DDR3 memory Storage in the system is handled by two 2 5 SATA 6Gb s SSD bays CFast card slot In addition the SBOX 100 QM87i features Intelligent Platform Management Interface 2 0 IPMI 2 0 that helps lower the overall costs of server management by enabling users to maximize IT resource save time and manage multipl
6. t t t t bt gt gt Y Step 4 username and password are Username admin Password admin Step 5 Press the login button to login the system Step 6 The IEI iMAN Web Interface appears Maintenance Firmware Update Integration Enter the user name and password to login system The default login To understand how to use the IEI Web GUI please refer to the IRIS 2400 Web GUI user manual in the utility CD came with the SBOX 100 QM87i The user manual describes each function in detail SBOX 100 QM87i Fanless Marine Computer Chapter 4 BIOS Setup m SBOX 100 QM87i Fanless Marine Computer 4 1 Introduction The BIOS is programmed onto the BIOS chip The BIOS setup program allows changes to certain system settings This chapter outlines the options that can be changed Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice 4 1 1 Starting Setup The UEFI BIOS is activated when the computer is turned on The setup program can be activated in one of two ways 1 Press the DEL or F2 key as soon as the system is turned on or 2 Press the DEL or F2 key when the Press DEL or F2 to enter SETUP message appears on the screen If the message disappears before the DEL or F2 key is pressed restart the compu
7. 76 Table 6 16 SATA Connector S ATA1 Pinouts J J J 77 Table 6 17 SATA Connector S 2 Pinouts J J J 77 Table 6 18 SATA Power Connector SATA PWR 1 Pinouts 77 Table 6 19 SATA Power Connector SATA_PWR 2 Pinouts 78 Table 6 20 SMBus Connector SMB1 78 Table 6 21 SPI Flash Connector 1 Pinouts J J J 78 Table 6 22 SPI Flash Connector CN2 79 Table 6 23 TPM Connector 1 Pinouts T 79 Table 6 24 Rear Panel Connectors J U J J 80 i Integration Integration Table 6 25 Table 6 26 Table 6 27 Table 6 28 Table 6 29 Table 6 30 Table 6 31 Table 6 32 SBOX 100 QM87i Fanless Marine Computer CAN Bus Connector Pinouts J J J 80 DVI Connector DVD Pinouts
8. 51 ITP 9 Ci OOM u unu Tte tV UM LEM 51 4 4 2 System Agent SA Configuration 53 4 4 2 1 Graphics Configuration 54 25 9 Memory Conf owr u teret ta 56 dopo E 56 ORI eee 58 ND ANTE SC sss e 59 AS SERVER MANAGEMENT n eee 60 2 TO LLG L PO L u aya 61 4 8 2 BMC Network Configuration 63 XU PS RIN b Tu usa E 64 5 1 SYSTEM MAINTENANCE 65 5 2 SO DIMM REPLACEMENT PROCEDURE csccscccccccecceccecceccecceccuscescescecceccescescesces 65 Integration Corp SBOX 100 QM87i Fanless Marine Computer 6 INTERFACE CONNECTORS 68 6 1 PERIPHERAL INTERFACE CONNECTORS 69 6 2 INTERNAL PERIPHERAL CONNECTORS 71 0 2 Audio Connector AUDIO T 72 0 2 2 Connector BATI aqayahaqqaykayiakasyapaqasaqapayqahqqasa 72 6 2 3 Chassis Intrusion Connector CHASSISI 6 2 4 Digital I
9. IE IEI Integration Corp 14019 SBOX 100 Q Dual Core CPU Intel QM87 Express Chipset GbE LAN HDMI DVI D VGA CAN Bus CFast Slot RS 232 422 485 USB 2 0 USB 3 0 iRIS 2400 ROHS Compliant User Manual Rev 1 00 June 4 2015 15 Integration Corp SBOX 100 QM87i Fanless Marine Computer Revision C June 4 2015 Initial release m e Integration Corp SBOX 100 QM87i Fanless Marine Computer Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability design and function and does not represent a commitment on the part of the manufacturer In no event will the manufacturer be liable for direct indirect special incidental or consequential damages arising out of the use or inability to use the product or documentation even if advised of the possibility of such damages This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer TRADEMARKS All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and or registered trademarks of their respective owners Page Ill LINFRODUC TION GG u 1 LOS R
10. Regulatory Compliance Page 84 SBOX 100 QM87i Fanless Marine Computer DECLARATION OF CONFORMITY This equipment is in conformity with the following EU directives m EMC Directive 2004 108 EC m Low Voltage Directive 2006 95 EC m RoHS 1 Directive 2011 65 EU m Ecodesign Directive 2009 125 EC If the user modifies and or install other devices in the equipment the CE conformity declaration may no longer apply If this equipment has telecommunications functionality it also complies with the requirements of the R amp TTE Directive 1999 5 EC English IEI Integration Corp declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Bulgarian IEI Integration Corp 1999 5 Cesky Czech IEI Integration Corp t mto prohla uje Ze tento za zen je ve shod se z kladn mi po adavky dal mi p slu n mi ustanoven mi sm rnice 1999 5 ES Dansk Danish IEI Integration Corp erkl rer herved at f lgende udstyr overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF Deutsch German IEI Integration Corp erkl rt dieses Ger t entspricht den grundlegenden Anforderungen un
11. Integration Corp SBOX 100 QM87i Fanless Marine Computer WARNING The precautions outlined in this chapter should be strictly followed Failure to follow these precautions may result in permanent damage to the SBOX 100 QM87i B 1 Safety Precautions Please follow the safety precautions outlined in the sections that follow B 1 1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times Follow the electrostatic precautions outlined below whenever the SBOX 100 QM87i is opened Make sure the power is turned off and the power cord is disconnected whenever the SBOX 100 QM87i is being installed moved or modified not apply voltage levels that exceed the specified voltage range Doing so may cause fire and or an electrical shock Electric shocks can occur if the 100 8 7 chassis is opened when the SBOX 100 QM8 i is running not drop or insert any objects into the ventilation openings of the SBOX 100 QM87i If considerable amounts of dust water or fluids enter the SBOX 100 QM87i turn off the power supply immediately unplug the power cord and contact the SBOX 100 QM87i vendor DO O Drop the SBOX 100 QM87i against a hard surface O Ina site where the ambient temperature exceeds the rated temperature sa agno EM SBOX 100 QM87i Fanless Marine Computer B 1 2 Anti static Precaut
12. eres A cceee 59 Save Changes and op ea EE aa 59 Discard Changes and Reset J U caa AG nC Quand 59 G uu uu uu 59 Save uu S 60 E 60 SEL Components Enabled 61 M gH 61 When SEL is Full DO Nothincg 62 Log EFI Status Codes 62 Configuration Address source Unspecified 63 a E Integration Corn qe SBOX 100 QM87i Fanless Marine Computer 3 Appendix D Watchdog Timer Page 97 Integration Corp SBOX 100 QM87i Fanless Marine Computer The following discussion applies to DOS environment IEI support is contacted the website visited for specific drivers for more sophisticated operating systems e g Windows and Linux The Watchdog Timer is provided to ensure that standalone systems can always recover
13. J J Q J J 72 Table 6 3 Battery Connector Pinouts J 72 Table 6 4 Chassis Intrusion Connector CHASSIS1 Pinouts 72 Table 6 5 Digital Connector 0101 Pinouts c eeceee J J 73 Table 6 6 EC Debug Connector LPT DB1 Pinouts 73 Table 6 7 Fan Connector CPU FAN 1 Pinouts T 73 Table 6 8 Front Panel Connector F_PANEL1 Pinouts 74 Table 6 9 IPMI LED Connector IPMI_LED1 Pinouts 74 Table 6 10 LAN Active LED Connector LAN ACT LED1 74 Table 6 11 PCle Mini Slots MINI PCIE1 MINI PCIE2 Pinout 75 Table 6 12 Power Connector PWR1 Pinouts 75 Table 6 13 Power Button Connector PWR BTN1 Pinouts erre eene 76 Table 6 14 PS ON Connector PS 1 Pinouts 76 Table 6 15 RS 232 422 485 Connectors COM2 5
14. Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 24 Server Management e wae Integration Corp AEN SBOX 100 QM87i Fanless Marine Computer 4 8 1 System Event Log Use the System Event Log menu BIOS Menu 25 to configure the system event log of the BMC Aptio Setup Utility Copyright C 2012 American Megatrends Inc Server Mgmt Enabling Disabling Option Change this to enable or SEL Components Enabled disable all features of System Event Logging Erasing Settings during No When SEL is Full Do Norhang Select Screen Custom EFI Logging Options Log EFI Status Codes Both Enter Select Changes NOTE All values changed here do not take effect Fl General Help until computer is restarted F2 Previous Values Is Optimized Defaults F4 Save amp Exit EOC BE Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 25 System Event Log SEL Components Enabled Use the SEL Components option to enable or disable all features of System Event Log SEL when the system boots gt Disabled DEFAULT System Event Log is disabled Enabled System Event Log is enabled Erase SEL No Use the Erase SEL option for erasing SEL gt No DEFAULT Do not erase system event log gt Yes On next Erase system event log on next reset reset I
15. Integration Corp gt SBOX 100 QM87i Fanless Marine Computer 4 3 10 1 Serial Port n Configuration Use the Serial Port n Configuration menu BIOS Menu 13 to configure the serial port n Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced J TNI M Enable or Disable Serial Port COM Serial Port Enabled Device Settings IO 3F8h IRQ 4 Change Settings Auto lt Select Screen 7 Select Item EnterSelect 1 1 Previous Values ES Optimized Defaults F4 Save ESC Boom m Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 13 Serial Port n Configuration Menu 4 3 10 1 1 Serial Port 1 Configuration gt Serial Port Enabled Use the Serial Port option to enable or disable the serial port gt Disabled Disable the serial port gt Enabled DEFAULT Enable the serial port gt Change Settings Auto Use the Change Settings option to change the serial port IO port address and interrupt address gt Auto DEFAULT The serial port IO port address and interrupt address are automatically detected gt IO 3F8h Serial Port I O port address is 3F8h and the interrupt IRQ 4 address is IRQ4 SBOX 100 QM87i Fanless Marine Computer gt IO 3E8h Serial Port I O port address is 3E8h and the interrupt IRQ 3 4 address is IRQ3 4 gt IO 2F8h Serial Port I O port address is 2F8h and the interrupt IRQ
16. blinking in red 1x IPMI LED indicator enabled blue disabled off 2 Knockout hole for SMA antenna connector RS 232 422 485 COM2 COM4 Power LED HDD CFast LED LED COM3 COM5 Figure 1 2 Front Panel The default settings for 2 5 are to 5 485 To configure the COM port mode please change the BIOS options in Advanced gt F81866 Super IO Configuration gt Serial Port Configuration refer to Section 4 3 10 1 SBOX 100 QM87i Fanless Marine Computer 1 4 Rear Panel The 5 100 87 rear panel provides access to the following external I O connectors 1 18V 36 V DC input terminal block 1 x Audio line in jack 1 x Audio line out jack 1 x Audio mic in jack 1 power mode switch 2 bus terminal block 1 x slot 1 Clear CMOS switch 1 x DVI D connector 2x RJ 45 connector 1 x HDMI connector 1 Keyboard Mouse PS 2 connector 1 Power button 1 x RS 232 9 serial port 2 USB 2 0 port connector 2 USB port connector 1 x VGA connector 2 x USB 2 0 AT ATX Switch CFast Slot 18 V 36V CAN Bus DC Input HDMI DVI Clear CMOS Line in Line out 9 Mic in Power Button RS 232 VGA GbE iRIS COM1 2 X USB 3 0 Keyboard Mouse Figure 1 3 Rear Panel m mo
17. from catastrophic conditions that cause the CPU to crash This condition may have occurred by external EMI or a software bug When the CPU stops working correctly Watchdog Timer either performs a hardware reset cold boot or a Non Maskable Interrupt NMI to bring the system back to a known state A BIOS function call INT 15H is used to control the Watchdog Timer INT 15H AH 6FH Sub function Sets the Watchdog period Time out value Its unit second is dependent on the item Watchdog Timer unit select in CMOS setup Table D 1 AH 6FH Sub function Call sub function 2 to set the time out period of Watchdog Timer first If the time out value is not zero the Watchdog Timer starts counting down While the timer value reaches zero the system resets To ensure that this reset condition does not occur calling sub function 2 must periodically refresh the Watchdog Timer However the Watchdog timer is disabled if the time out value is set to zero A tolerance of at least 10 must be maintained to avoid unknown routines within the operating system DOS such as disk I O that can be very time consuming SBOX 100 QM87i Fanless Marine Computer When exiting a program it is necessary to disable the Watchdog Timer otherwise the system resets Example program INITIAL TIMER PERIOD COUNTER W_LOOP MOV MOV INT AX 6F02H BL 30 15H setting the
18. off Does not enable the keyboard Number Lock automatically To use the 10 keys on the keyboard press the Number Lock key located on the upper left hand corner of the 10 key pad The Number Lock LED on the keyboard lights up when the Number Lock is engaged Quiet Boot Enabled Use the Quiet Boot BIOS option to select the screen display when the system boots gt Disabled Normal POST messages displayed Enabled DEFAULT OEM Logo displayed instead of POST messages Option ROM Messages Force BIOS Use the Option ROM Messages option to set the Option ROM display mode gt Force DEFAULT Sets display mode to force BIOS BIOS gt Keep Sets display mode to current Current SBOX 100 QM87i Fanless Marine Computer gt Launch PXE OpROM Disabled Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices gt Disabled DEFAULT Ignore all PXE Option ROMs gt Enabled Load PXE Option ROMs gt Boot Disabled Use the UEFI Boot option to enable or disable to boot from the UEFI devices gt Disabled DEFAULT Boot from UEFI devices is disabled gt Enabled Boot from devices is enabled 4 6 Security Use the Security menu BIOS Menu 22 to set system and user passwords Aptio Setup Utility Copyright 2012 American Megatrends Inc Main Advanced Chipset Boot Security e Password Description Set Administrator Pas
19. 3 4 address is IRQ3 4 gt IO 2C0h Serial Port I O port address is 2COh the interrupt IRQ 3 4 address is IRQ3 4 gt IO 2C8h Serial Port I O port address is 2C8h and the interrupt IRQ 3 4 address is IRQ3 4 4 3 10 1 2 Serial Port 2 Configuration Serial Port Enabled Use the Serial Port option to enable or disable the serial port gt Disabled Disable the serial port Enabled DEFAULT Enable the serial port gt Change Settings Auto Use the Change Settings option to change the serial port 10 port address and interrupt address gt Auto DEFAULT The serial port IO port address and interrupt address are automatically detected gt IO 2F8h Serial Port I O port address is 2F8h and the interrupt IRQ 3 address is IRQ3 gt IO 3F8h Serial Port I O port address is 3F8h and the interrupt IRQ 3 4 address is IRQ3 4 gt IO 2F8h Serial Port I O port address is 2F8h and the interrupt IRQ 3 4 address is IRQ3 4 gt IO 2C0h Serial Port I O port address is 2C0h and the interrupt IRQ 3 4 address is IRQ3 4 SBOX 100 QM87i Fanless Marine Computer gt IO 2C8h Serial Port I O port address is 2C8h and the interrupt IRQ 3 4 address is IRQ3 4 Serial Port Mode RS485 Use the Serial Port Mode option to set the Serial Port 2 signaling mode gt Rs232 Configure Serial Port 2 as RS 232 RS422 Configure Serial Port 2 as RS 422 5485 DEFAULT Configure Serial Port 2 as RS 485 4 3 10 1 3 Se
20. Change Settings Auto Use the Change Settings option to change the serial port port address and interrupt address gt Auto DEFAULT The serial port IO port address and interrupt address are automatically detected gt lO 2E8h Serial Port I O port address is 2E8h and the interrupt IRQ 10 address is IRQ10 2 lO 3E8h Serial Port I O port address is 3E8h and the interrupt IRQ 10 11 address is IRQ10 11 SBOX 100 QM87i Fanless Marine Computer gt IO 2E8h Serial Port I O port address is 2E8h and the interrupt IRQ 10 11 address is IRQ10 11 gt IO 2D0h Serial Port I O port address is 2D0h and the interrupt IRQ 10 11 address is IRQ10 11 gt IO 2D8h Serial Port I O port address is 2D8h and the interrupt IRQ 10 11 address is IRQ10 11 Serial Port Mode RS485 Use the Serial Port Mode option to set the Serial Port 4 signaling mode 5232 Configure Serial Port 4 as RS 232 RS422 Configure Serial Port 4 as RS 422 gt RS485 DEFAULT Configure Serial Port 4 as RS 485 4 3 10 1 5 Serial Port 5 Configuration gt Serial Port Enabled Use the Serial Port option to enable or disable the serial port gt Disabled Disable the serial port gt Enabled DEFAULT Enable the serial port gt Change Settings Auto Use the Change Settings option to change the serial port 10 port address and interrupt address gt Auto DEFAULT The serial port IO port address and interrupt address are automatically dete
21. O Connector 73 6 2 5 Debug Connector LPT DB 2 c 73 6 2 6 Fan Connector CPU 73 6 2 7 Front Panel Connector F_PANELLI 74 6 2 8 IPMI LED Connector IPMI_LED1 74 6 2 9 LAN Active LED Connector LAN ACT LED1 74 6 2 10 PCIe Mini Slots MINI PCIEI MINI PCIE2 74 0 2 1 Power Connector PWRI 72 6 2 12 Power Button Connector PWR_BTNI 6 6 213 PS_ON Connector PS ON u teense 6 6 2 14 RS 232 422 485 Connector COM2 6 0 2 15 SATA Connector S od Dl 76 O21 O SATA Connector 9 qu 77 6 2 17 SATA Power Connector SATA_PWR1 77 6 2 18 SATA Power Connector SATA_PWR2 78 6 2 19 SMBus Connector EC SMB1 78 OLLOS L ia 78 6 2 21 SPI Flash Connector EC CN2 79 0 2 22 TPM Connector EPMT 79 6 3 EXTERNAL INTERFACE PANEL CONNEC
22. QM87i c The SBOX 100 QM87i boots from the USB flash drive d Enter the following command ipmitool 20 30 02 01 03 00 00 there is a space between each two digit number e Aserial of number shows The last four two digit hexadecimal numbers are the IP address Convert the hexadecimal numbers to decimal numbers Step 2 remote management console open web browser Enter the managed system IP address in the web browser Figure 3 15 5 10 10 1873 Figure 3 15 Web Address Step 3 The login page appears in the web browser SF A 51040J4 1605n cx html SBOX 100 QM87i Fanless Marine Computer Dashboard FRU information Server Heelih Configuration Remote Control Video Recording Dashboard Dashboard gives the overall information about the status of he device and remote server Device Information Firmware Revision 07020910 Firrmeare Budd Time Dec 17 2013 12 26 20 CST Revision 8271ER25 Network Information Lan Address 12 34 56 98 86 88 Network Mode IPv Address 105014160 V Nebw rk Mode 1 Address Remote Control Sensor Monitoring f e e 5 Senna Readng CPU_TEMPI 338 C 575_ 23 C CPU CORE 1 7423 Vows 5 135 Vols 12 175 Vote 1 487 0 079 Vots 3 343 Vots 3 279 Vots CPU FAN 08 ORPN Figure 3 16 IEI iMAN Web GUI A NOTE
23. is SATA PWR1plus SATA PWR2 Total 12V SATA power is SATA PWR1plus SATA PWR2 Table 6 18 SATA Power Connector SATA PWR1 Pinouts Table 6 19 SATA Power Connector SATA_PWR2 Pinouts 6 2 19 SMBus Connector EC SMB1 Table 6 20 SMBus Connector EC SMB1 6 2 20 SPI Flash Connector SPI1 Table 6 21 SPI Flash Connector SPI1 Pinouts S E es Integration Corp SBOX 100 QM87i Fanless Marine Computer 6 2 21 SPI Flash Connector EC 2 DESCRIPTION SMCLK1 EC SMDAT1 EC Table 6 22 SPI Flash Connector EC CN2 6 2 22 TPM Connector TPM1 Table 6 23 TPM Connector TPM1 Pinouts 6 3 External Interface Panel Connectors The table below lists the rear panel connectors on the SBOX 100 QM87i motherboard Pinouts of these connectors can be found in the following sections ATX AT mode switch J ATXCTL1 6 pin terminal block CAN1 Clear CMOS button Push button J CMOS1 DVI VGA combo connector DVI 15 pin female D sub SBOX 100 QM87i Fanless Marine Computer HDMI connector HDMI Keyboard mouse and USB 2 0 combo connector PS 2 K B USB1 USB 2 0 port GbE connectors RJ 45 LAN1 2 CN1 RS 232 serial port COM1 USB 3 0 connectors USB 3 0 port USB3 Table 6 24 Rear Panel Connectors 6 3 1 CAN Bus Connector CAN1 gt em e _ s
24. is powered to RAM off Power to the RAM is maintained The computer returns slower to a working state but more power is saved SBOX 100 QM87i Fanless Marine Computer 4 3 2 RTC Wake Settings The RTC Wake Settings menu BIOS Menu 4 configures RTC wake event Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced Wake system with Fixed Time Disabled Enable or disable System wake on alarmevent When enabled System will wake on the dat Pro mini See specifieq lt Select Screen Select Item Enterselect to Change General Help F2 Previous Values F3 Optimized Defaults F4 Version 2 15 1236 Copyright 2012 American Megatrends Inc BIOS Menu 4 RTC Wake Settings Wake System with Fixed Time Disabled Use the Wake System with Fixed Time option to specify the time the system should be roused from a suspended state gt Disabled DEFAULT The real time clock RTC cannot generate a wake event s ia Em Integration Corp S SBOX 100 QM87i Fanless Marine Computer 9 WW Enabled If selected the following appears with values that can be selected Wake up every day Wake up date Wake up hour Wake up minute Wake up second After setting the alarm the computer turns itself on from a suspend state when the alarm goes off 4 3 3 Trusted Computing Use the Trusted C
25. meme Table 6 25 CAN Bus Connector Pinouts 6 3 2 DVI Connector DVI we oscuro ETT TIEN s essemus e 7 eem oe Table 6 26 DVI Connector DVI Pinouts SBOX 100 QM87i Fanless Marine Computer 6 3 3 VGA Connector VGA1 2 e Integration Corp DESCRIPTION DESCRIPTION Table 6 27 VGA Connector VGA1 Pinouts 6 3 4 HDMI Connector HDMI1 DESCRIPTION LL DESCRIPTION 2 f 1 HDMI_DATA1 aa rama is HPD Table 6 28 HDMI Connector HDMI1 Pinouts Integration Corp SBOX 100 QM87i Fanless Marine Computer 6 3 5 GbE Connectors LAN1 2 CN1 PIN NO DESCRIPTION DESCRIPTION 1 2 ewe e pem ee pee Table 6 29 RJ 45 GbE Connector LAN1 2 CN1 Pinouts 6 3 6 RS 232 Serial Port COM1 LIA DESCRIPTION LIN DESCRIPTION Table 6 30 RS 232 Serial Port COM1 Pinouts 6 3 7 USB 2 0 Connectors USB1 mao 2 je _ Table 6 31 USB 2 0 Connector USB1 Pinouts SBOX 100 QM87i Fanless Marine Computer 6 3 8 USB 3 0 Connectors USB3_CN1 s s USB DATA c USB_DATA Bode Table 6 32 USB 3 0 Connector 0583 CN1 Pinouts SBOX 100 QM87i Fanless Marine Computer Appendix A
26. power the system UN 21 Integration SBOX 100 QM87i Fanless Marine Computer 18 V 36 V DC Power Input Terminal Block Power Button Figure 3 13 Power Connector and Power Button 3 9 Clear CMOS If the SBOX 100 QM87i fails to boot due to improper BIOS settings the clear CMOS button clears the CMOS data and resets the system BIOS information To do this push the clear CMOS button for three seconds and then restart the system The clear CMOS button location is shown in Figure 3 14 Clear CMOS Button Figure 3 14 Clear CMOS Button Location 3 10 Driver Installation The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice Visit the IEI website or contact technical support for the latest updates SBOX 100 QM87i Fanless Marine Computer All the drivers for the SBOX 100 QM87i are on the utility CD that came with the system The utility CD contains drivers for Windows 7 and Windows 8 operating systems Please select the corresponding drivers for the system and follow the step by step procedure to install each driver The following drivers can be installed on the Windows 7 operating system Chipset Graphics LAN Audio CAN bus USB 3 0 The following drivers can be installed on the Windows 8 operating system Chipset Graphics LAN Audio CAN b
27. s 5V Select Item ELE ec jin a EnterSelect DDR suspe OE Wels 5 044 V F1 General Help 13 23 323 V F2 Previous Values l Optimized Defaults FA Save amp Exit Version 2 15 1236 Copyright 2012 American Megatrends Inc BIOS Menu 11 iWDD H W Monitor H W Monitor The following system parameters and values are shown The system parameters that are monitored are CPU Temperature System Temperature Voltages O CPU_CORE O 5V O 12V O DDR Integration Corp SBOX 100 QM87i Fanless Marine Computer O 5VSB O 3 3V O 3 3VSB 4 3 10 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu BIOS Menu 12 to set or change the configurations for the serial ports Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced F81866 Super IO Configuration Set Parameters of Serial Port 1 COMA sure 10 Chip F81866 ri e Eomae TP l qs sto on Serial Pore Cont ton Serial Port Serial Port Configuration Select Item Om eu von EnterSelect F1 General Help E Previous Values F3 Optimized Defaults F4 Version 2 15 1236 Copyright 2012 American Megatrends Inc BIOS Menu 12 F81866 Super IO Configuration 2 Seriol Port j 4 5 a ame _
28. to select the graphics controller used as the primary boot device Configuration options are listed below Auto Default PCIE gt DVMT Pre Allocated 256M Use the DVMT Pre Allocated option to set the amount of system memory allocated to the integrated graphics processor when the system boots The system memory allocated can then only be used as graphics memory and is no longer available to applications or the operating system Configuration options are listed below 32M SBOX 100 QM87i Fanless Marine Computer 64M 128M 256M Default 512M DVMT Total Gfx Mem 256M Use the DVMT Total Gfx Mem option to select DVMT5 0 total graphic memory size used by the internal graphic device The following options are available 128M 256M DEFAULT Primary IGFX Boot Display VBIOS Default Use the Primary IGFX Boot Display option to select the display device used by the system when it boots Configuration options are listed below VBIOS Default DEFAULT DVI HDMI 1 Display port 1 SBOX 100 QM87i Fanless Marine Computer 4 4 3 Memory Configuration Use the Memory Configuration submenu BIOS Menu 20 to display the memory information Aptio Setup Utility Copyright C 2012 American Megatrends Inc Chipset Memory Information Memory Frequency 1600 Mhz Total Memory MB DDR DIMM 1 2048 MB DDR3 lt gt Select Scree
29. 012 American Megatrends Inc Chipset Wo Cejoelem ancy Supported Check to enable VI d Disabled ON MCH Pp gt Memory Configuration j Select Item EnterSelect Change Opt F1 General Help F Previous Values F3 Optimized Defaults 4 Save amp Exit ESC Exist Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 18 System Agent SA Configuration VT d Disabled Use the VT d option to enable or disable VT d support Disabled DEFAULT Disable VT d support gt Enabled Enable VT d support SBOX 100 QM87i Fanless Marine Computer 4 4 2 1 Graphics Configuration Use the Graphics Configuration submenu BIOS Menu 19 to configure the graphics settings Aptio Setup Utility Copyright C 2012 American Megatrends Inc Chipset Graphics Conti CRUS Select which of Primary Display Auto IGFX PEG PCI Graphics DVMT Pre Allocated 256M device should be Primary DVMT Total Gfx Mem MAX Display Or select SG for Switchable Gfx Primary Boot Display VBIOS Default 2 Select Screen V Select Item EnterSelect Change General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit BE Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 19 Graphics Configuration Primary Display Auto Use the Primary Display option
30. 3 Installation Page 12 e integration Corp S SBOX 100 QM87i Fanless Marine Computer 3 1 Installation Precautions During installation be aware of the precautions below Read the user manual The user manual provides a complete description of the 5 100 8 71 installation instructions and configuration options DANGER Disconnect Power Power to the SBOX 100 QM87i must be disconnected during the installation process or before any attempt is made to access the rear panel Electric shock and personal injury might occur if the rear panel of the SBOX 100 QM87i is opened while the power cord is still connected to an electrical outlet Qualified Personnel The SBOX 100 QM87i must be installed and operated only by trained and qualified personnel Maintenance upgrades or repairs may only be carried out by qualified personnel who are familiar with the associated dangers Air Circulation Make sure there is sufficient air circulation when installing the SBOX 100 QM87i The SBOX 100 QM87i s cooling vents must not be obstructed by any objects Blocking the vents can cause overheating of the SBOX 100 QM87i Leave at least 5 cm of clearance around the SBOX 100 QM87i to prevent overheating Grounding The SBOX 100 QM87i should be properly grounded The voltage feeds must not be overloaded Adjust the cabling and provide external overcharge protection per the electrical values indicated on the lab
31. IMER 97 E HAZARDOUS MATERIALS DISCLOSURE 100 E 1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS ROHS COMPLIANT UNDER 2002 95 EC WITHOUT MERCURY 101 Page VII Integration Corp Integration Corp SBOX 100 QM87i Fanless Marine Computer List of Figures Figure 1 1 SBOX 100 QM87i Fanless Marine Computer 2 Figure 2 Front Panel i 3 Foure Ta Rear Pane L uu enamels ace 4 Figure 1 4 SBOX 100 QM87i Dimensions mm J 7 Figure 3 1 CFast Slot Cover Retention Screw J 14 Figure 3 2 CFast Card Installation J cuc duc a onn J uu unn an J Q T T J J 14 Figure 3 3 Bottom Cover Retention Screws 15 Figure 3 4 HDD Bracket Retention Screws J J J nnn 15 FIGUIE 3 5 Inserting the LLL LLULLU LR uuu u u uuu u u 16 Figure 3 6 I talling HDD 16 Figure 3 7 AT ATX Mode Seleclioiu
32. Menu 7 SATA Configuration uU Uu uay 37 BIOS Menu 8 Intel Rapid Start Technology J U J nnns 38 BIOS Menu 9 AMT Contiguration UL Uu uu 39 BIOS Menu 10 USB Contiguration aU nj Baa ua Cu Xa 40 BIOS Menu 11 WDD HW Monitor J idu 41 BIOS Menu 12 F81866 Super IO Configuration J J J J J 42 BIOS Menu 13 Serial Port n Configuration Menu J J 43 BIOS Menu 14 Serial Port Console Redirection J J T J J 49 zi NC MINUTE 50 BIOS Menu CID SOU Tuya pans I uide debe puedo 51 BIOS Menu 17 PCH IO Configuration J J 51 BIOS Menu 18 System Agent SA Configuration J 53 BIOS Menu 19 Graphics Configuration J J J J Q J 54 BIOS Menu 20 Memory Configuration J U J
33. Power paving won ERP Disabled Enabled Azalia will be unconditionally Enabled lt gt elect Select Item Enterselect T Chance Opt General Help Previous Values FS Optimized Defaults F4 Save amp Exit EE Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 17 PCH IO Configuration Integration Corp SBOX 100 QM87i Fanless Marine Computer gt Azalia HD Audio Enabled Use the Azalia HD Audio option to enable or disable the High Definition Audio controller gt Disabled The onboard High Definition Audio controller is disabled Enabled DEFAULT The onboard High Definition Audio controller automatically detected and enabled gt Serial IRQ Mode Continuous Use the Serial IRQ Mode option to configure serial IRQ mode for serial interrupts Configuration options are listed below Quiet Continuous DEFAULT Power Saving Function ERP Disabled Use the Power Saving Function ERP option to enable or disable the power saving function Disabled DEFAULT Disable the power saving function Enabled Enable the power saving function ia L3 Integration SBOX 100 QM87i Fanless Marine Computer 4 4 2 System Agent SA Configuration Use the System Agent SA Configuration menu BIOS Menu 18 to configure the System Agent SA parameters Aptio Setup Utility Copyright C 2
34. S 232 Serial Port COM1 Pinouts 3 6 2 RS 232 422 485 Serial Port COM2 5 The RS 232 422 485 mode selection of COM2 5 is made through the system BIOS Please refer to Section 4 3 10 1 for selecting COM port mode The default setting for COM 5 is RS 485 The RS 232 422 485 serial port pinouts are listed in the following table mee qum em ee fe fer p oo fm pee Table 3 2 RS 232 422 485 Serial Port Pinouts Integration Corp SBOX 100 QM87i Fanless Marine Computer 3 7 CAN Bus Connection and Configuration The SBOX 100 QM87i has CAN bus connector for CAN bus connection The pinouts for the CAN bus connector are listed in the figure and table below 5 1 6 2 Figure 3 10 CAN Bus Connector PIN NO DESCRIPTION PINNO DESCRIPTION Table 3 3 CAN Bus Connector Pinouts The on board jumpers JP1 and JP2 can be used for CAN bus configuration The jumper settings and locations are listed below 64 n JP1 Figure 3 11 CAN Bus Jumper Locations Long wire transmitting Table 3 4 CAN Bus Jumper Settings 3 8 Powering On the System To power on the system follow the steps below Step 1 Connect the power cable to the 3 pin power input terminal block The pinouts of the power input connectors are shown below V Earth Ground Figure 3 12 Power Input Connector Pinouts Step 2 Push the power button on the panel to
35. SLOPE UNS EEA TON m 22 3 11 SETUP PROCEDURE c ccssccccssssccccscssscccccnssccceensecessenssceseansscesseusscessenesceses 23 3 11 1 Managed System Hardware Setup 3S2 U sine the TELIMAN WED uui uuu 24 28 118 5 4 M UI Lr 26 Page IV SBOX 100 QM87i Fanless Marine Computer 2 e Integration Corp ZI INBRODUGTION mee ee ee 21 dT S Tl SAUD E 27 USES T sn 27 28 D 28 29 30 ERE EE E 31 E ku 32 TUS ICO r 1 3 T sss sss ss 33 4 34 CPU 34 PASSATA Eo nui 37 4 3 6 Intel Rapid Start Faser gt 38 u a 39 APO USD 417 1 1919 40 2 3 0 IWDD ITI W iu anasu hawa EEEE 41 4 3 10 F81866 Super IO 42 4 3 10 1 Serial Port CONMSULAION adris 43 4 3 11 Serial Port Console Redirection 48 E 50 mieu jl
36. TORS 79 6 3 1 CAN Bus Connector CAN1 50 CIOL 50 6 3 3 VGA Connector VGA Ted 61 6 3 4 HDMI Connector HDMITIT eeeesseeeeeeeeeeeeeee eene hene hehehe nennen nnne nan 61 6 3 5 GbE Connectors LAN1 2 CN1 52 RS 252 Serial Vort 52 6 3 USB 20 Connectors CUS BI 52 6 3 8 USB 3 0 Connectors USB3_CN1 83 Page VI SBOX 100 QM87i Fanless Marine Computer AREGULATORY COMPLIANCE 84 O E E E 89 BSATEN AULON sger a A 90 IND General Safety 90 1 2 9 PAGS Po D 92 B 2 MAINTENANCE AND CLEANING PRECAUTIONS 92 2 1 Maintenance Cleaninsg 92 BDC COMIN TOOT gt __ __4 6_ 6____ 93 C BIOS sus 94 1 BIOS CONFIGURATION OPTIONS ssseecceceeeeeeeesssaneeeeeeeeessessaaeeeeeeeeeeeessnaaeeeeeees 95 DMALCHDOG T
37. Virtualization Technology EIST Enabled Use the EIST option to enable or disable the Enhanced Intel SpeedStep Technology EIST gt Disabled Disable Enhanced Intel SpeedStep Technology Enabled DEFAULT Enable Enhanced Intel SpeedStep Technology Intel TXT LT Support Disabled Use the Intel TXT LT Support option to enable or disable the Intel Trusted Execution Technology gt Disabled DEFAULT Disable Intel Trusted Execution Technology Enabled Enable Intel Trusted Execution Technology ia Integration 4 LI Corp gt SBOX 100 QM87i Fanless Marine Computer lil 4 3 5 SATA Configuration Use the SATA Configuration menu BIOS Menu 7 to change and or set the configuration of the SATA devices installed in the system Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced SATA Controller s Enabled Enable or disable SATA SATA Mode Selection IDE Device Chast Empty 5 Empty 5 Empty lt Select Screen V Select Item EnterSelect po menge Im General Help n Previous Values Optimized Defaults F4 Save EOC BUE Version 2 15 1236 Copyright 2012 American Megatrends Inc BIOS Menu 7 SATA Configuration gt SATA Controller s Enabled Use the SATA Controller s option to configure the SATA controller s Enabled DEFAULT Enable the on board SATA controller
38. WIS WV uuu _____ _ _ ______ 2 L l E 5 E E 2 LT ONT PAN 3 Fili E 3 1 5 TECHNICAL SPECIFICATIONS roue ERR ee Per RU e 5 X 7 INC uu EEEE 8 2 1 ANTI STATIC PRECAUTIONS a 9 2 2 UNPACKING PRC 9 LINC 10 SN EE YN TION i u 12 O 13 3 1 1 High Surface Temperature 13 3 2 CFAST CARD 14 INSTALLATION 15 JAAT ATX MODE SELECTION 17 3 3 MOUNTING THE SYSTEM ee 17 3 6 SERIAL DEVICE CONNECTION 18 JOA RS 252 Serial Port COMI 19 3 6 2 5 232 422 485 Serial Port COM2 COM5 19 3 7 BUS CONNECTION AND CONFIGURATION 20 3 8 POWERING ON THE a 21 ADC MO nner 22
39. ade through an AT ATX switch on the I O interface panel The switch is shown below ATX AT Figure 3 7 AT ATX Mode Selection 3 5 Mounting the System The mounting brackets on both sides of the 100 8 7 allow it to be mounted onto a wall or some other surface To mount the system align the mounting holes in the mounting brackets with the holes in the mounting surface Then insert retention screws in each bracket to secure the system to the surface Mounting Brackets with Mounting Holes Figure 3 8 Mounting Brackets Integration Corp SBOX 100 QM87i Fanless Marine Computer 3 6 Serial Device Connection The 100 87 series has five serial ports including four RS 232 422 484 ports on the front panel and one RS 232 port on the rear panel The port locations are shown in Figure 3 9 The pinouts of the serial ports are listed in the following sections RS 232 422 485 COM2 COM4 RS 232 COM Figure 3 9 Serial Port Locations The default settings for 2 5 are to 5 485 To configure the COM port mode please change the BIOS options in Advanced gt F81866 Super IO Configuration gt Serial Port Configuration refer to Section 4 3 10 1 SBOX 100 QM87i Fanless Marine Computer 3 6 1 RS 232 Serial Port COM1 The pinouts of the RS 232 serial port are listed in the following table DESCRIPTION m DESCRIPTION Table 3 1 R
40. ange General Help F2 Previous Values F3 Optimized Defaults 4 Save amp Exit ESC EXIL Version 2 15 1236 Copyright 2012 American Megatrends Inc BIOS Menu 23 Save amp Exit gt Save Changes and Reset Use the Save Changes and Reset option to save the changes made to the BIOS options and reset the system gt Discard Changes and Reset Use the Discard Changes and Reset option to exit the system without saving the changes made to the BIOS configuration setup program gt Restore Defaults Use the Restore Defaults option to load the optimal default values for each of the parameters on the Setup menus F3 key can be used for this operation SBOX 100 QM87i Fanless Marine Computer Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options 4 8 Server Management Use the Server Mgmt menu BIOS Menu 24 to configure BMC network parameters Aptio Setup Utility Copyright 2012 American Megatrends Inc Main Advanced Chipset Boot Sena Server Mgmt BMC Selrt Test Status FATLED Configure BMC network Deus euet exe gt BMC network configuration Oe EIN Select Item EnterSelect Change Opt General Help F2 Previous Values Optimized Defaults 4 Save amp Exit F
41. ard Layout Diagram Solder Side SBOX 100 QM87i Fanless Marine Computer 6 2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis The table below shows a list of the peripheral interface connectors on the SBOX 100 QM87i motherboard Pinouts of these connectors can be found in the following sections PCle Mini card slots PCle Mini card slot MINI PCIE1 MINI PCIE2 Power button connector PWR BTN1 PS ON connector 3 pin header PS ON1 RS 232 422 485 connector 10 pin header 2 COM3 COM4 COM5 SATA connectors 7 pin connector SATA power connectors 4 pin wafer SATA PWR1 SATA PWR2 Integration Corp SBOX 100 QM87i Fanless Marine Computer Table 6 1 Peripheral Interface Connectors 6 2 1 Audio Connector AUDIO1 DESCRIPTION CUN DESCRIPTION MI C L Table 6 2 Audio Connector AUDIO1 Pinouts 6 2 2 Battery Connector BAT1 Table 6 3 Battery Connector BAT1 Pinouts 6 2 3 Chassis Intrusion Connector CHASSIS1 EC CHASSIE EC Table 6 4 Chassis Intrusion Connector CHASSIS1 Pinouts SBOX 100 QM87i Fanless Marine Computer 6 2 4 Digital Connector DIO1 Table 6 5 Digital Connector DIO1 Pinouts 6 2 5 EC Debug Connector LPT_DB1 Table 6 6 EC Debug Connector LPT_DB1 Pinouts 6 2 6 Fan Connector 1 DESCRIPTION Ro
42. bs for cleaning SBOX 100 QM87i Fanless Marine Computer Appendix C BIOS Menu Options Page 94 SBOX 100 QM87i Fanless Marine Computer C 1 BIOS Configuration Options Below is a list of BIOS configuration options described in Chapter 4 Sj EC yk o d uuu ua asa ENTE 30 System Time uu 30 ACPI Sleep State 51 only CPU Stop Clock 31 Wake System with Fixed Time Disabled 32 Security Device Support Disable uaa J 34 riyper Ihnreading Disabled u uuu u U UU TL 35 Active Processor Cores All tr UR Sk 35 Intel Virtualization Technology Disabled 36 36 Intel TXT LT Support Disabled J J J 36 SATA Controller s Enabled f EU CD ER 37 SATA Mode Selection IDE U IR UNUM UE 37 Intel R Rapid Start Technology Disabled
43. cedures must be followed to ensure the system can continue to operate normally 5 2 SO DIMM Replacement Procedure WARNING Users are not advised to attempt to repair or replace any internal or external components of the SBOX 100 QMe87i other than those listed below If any other components fail or need replacement contact the IEI reseller or vendor you purchased the SBOX 100 QM8 7i from or contact an IEI sales representative directly To contact an IEI sales representative please send an email to sales ieiworld com Integration SBOX 100 QM87i Fanless Marine Computer WARNING Using incorrectly specified SO DIMM may cause permanently damage the SBOX 100 QM87i Please make sure the purchased SO DIMM complies with the memory specifications of the SBOX 100 QM87i To replace a SO DIMM into a SO DIMM socket please follow the steps below Step 1 Remove the bottom cover by removing the 11 retention screws Figure 5 1 Bottom Cover Retention Screws Step 2 Locate the SO DIMM Figure 5 2 Two Preinstalled 2GB DDR3 SO DIMMs Figure 5 2 SO DIMM Locations Page 66 SBOX 100 QM87i Fanless Marine Computer Step 3 Remove the cable tie that secures the heatsink with the SO DIMM Then remove the heatsink Step 4 Release the arms on the SO DIMM socket to remove the SO DIMM Step 5 Align the new SO DIMM with the socket The SO DIMM must be oriented in such a way t
44. configured Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced inre i Enabled Enable Disable Intel Un Configure ME Disabled Active Management BIOS Extension Note iAMT H W is always enabled Oe Wem Boeke controls the BIOS extension execution If enabled this requires additional firmware in the SPI device elect erect 7 Select Item Enterselect Change Opt General Help Previous Values Optimized Defaults Save amp Exit EXIT Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 9 AMT Configuration Intel AMT Enabled Use Intel AMT option to enable or disable the Intel amp Active Management Technology gt Disabled Intel AMT is disabled gt Enabled DEFAULT Intel AMT is enabled Un Configure ME Disabled Use the Un Configure ME option to perform ME unconfigure without password operation gt Disabled DEFAULT Disable ME unconfigure SBOX 100 QM87i Fanless Marine Computer Enabled Enable ME unconfigure 4 3 8 USB Configuration Use the USB Configuration menu BIOS Menu 10 to read USB configuration information and configure the USB settings Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced USB Comm OI Enables Legacy USB cpr USB Devices disables legacy support 1 Keyboard 2 Hubs if no USB devices are connecte
45. cted gt IO 2D0h Serial Port I O port address is 2DOh and the interrupt IRQ 11 address is IRQ11 SBOX 100 QM87i Fanless Marine Computer gt IO 2C0h Serial Port I O port address is 2COh the interrupt IRQ 10 11 address is IRQ10 11 gt IO 2C8h Serial Port I O port address is 2C8h and the interrupt IRQ 10 11 address is IRQ10 11 gt IO 2D0h Serial Port I O port address is 2DOh and the interrupt IRQ 10 11 address is IRQ10 11 2 lO 2D8h Serial Port I O port address is 2D8h and the interrupt IRQ 10 11 address is IRQ10 11 Serial Port Mode RS485 Use the Serial Port Mode option to set the Serial Port 5 signaling mode 5232 Configure Serial Port 5 as RS 232 gt RS422 Configure Serial Port 5 as RS 422 gt RS485 DEFAULT Configure Serial Port 5 as RS 485 4 3 11 Serial Port Console Redirection The Serial Port Console Redirection menu BIOS Menu 14 allows the console redirection options to be configured Console redirection allows users to maintain a system remotely by re directing keyboard input and text output through the serial port ia amo E Integratio SBOX 100 QM87i Fanless Marine Computer Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced COMI Console Redirection Console Redirection Disabled gt Console Redirection Settings COM2 Console Redirection Disabled gt Console Redire
46. ction Settings COM3 Console Redirection Disabled gt Console Redirection Settings COM4 Console Redirection Disabled gt Console Redirection Settings 5 Dasa red lt gt Select Screen gt Console Redirection Settings Select Item EnterSelect COM6 BMC Disabled t Change Console Redirection Port Is Disabled EI General Help F2 Previous Values SOL F3 Optimized Defaults F4 Save Per Bus Devo Disabled m e Console Redirection Port Disable Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 14 Serial Port Console Redirection Console Redirection Enabled Use Console Redirection option to enable or disable the console redirection function gt Disabled Disabled the console redirection function gt Enabled DEFAULT Enabled the console redirection function SBOX 100 QM87i Fanless Marine Computer 4 3 12 IEI Feature Use the IEI Feature menu BIOS Menu 15 to configure One Key Recovery function Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced 1 1 Feature Auto Recovery Function Reboot and recover Auto Recovery Function Disabled system automatically within 10 min when OS crashes Please install REcovery API service before enabling Pie c Select Select Item EnterSelect Change Opt General Help Previ
47. d DISABLE Legacy USB Support Enabled option will keep USB devices available only lh lt gt O Select Item Enterselect Change Opt General Help Previous Values Optimized Defaults Save amp Exit apne Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 10 USB Configuration USB Devices The USB Devices Enabled field lists the USB devices that are enabled on the system Legacy USB Support Enabled Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support Normally if this option is not enabled any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded When this option is enabled any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system ia s iE Integration SBOX 100 QM87i Fanless Marine Computer Enabled DEFAULT Legacy USB support enabled gt Disabled Legacy USB support disabled gt Auto Legacy USB support disabled if no USB devices are connected 4 3 9 iWDD H W Monitor The IWDD H W Monitor menu BIOS Menu 11 displays operating temperature and system voltages Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced PC Health Status CPU Temperature 26 system temperature DEO CPU CORE 1403 gt O or
48. d den weiteren entsprechenden Vorgaben der Richtlinie 1999 5 EU Eesti Estonian IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 1999 5 EU p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele Integration Corp Page 86 SBOX 100 QM87i Fanless Marine Computer Espa ol Spanish IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999 5 CE EAAnvikn Greek IEI Integration Corp AHAQNEI OTI EZ ONAIZMOZ TI gt OYZIOAEIZ ANAITHZEI2 KAI 112 AOITIEZ ZXETIKE2Z AIATA EIZ TH gt 1999 5 EK Frangais French IEI Integration Corp d clare que l appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE Italiano Italian IEI Integration Corp dichiara che questo apparecchio conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Latviski Latvian IEI Integration Corp deklare ka iekarta atbilst b tiskajam prasibam un citiem ar to saistitajjem noteikumiem Direktivas 1999 5 EK Lietuviu Lithuanian IEI Integration Corp deklaruoja kad Sis jranga atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas Nederlands Dutch IEI Integration Corp dat het toestel toestel in overeenstemming is met de essenti l
49. e eisen en de andere relevante bepalingen van richtlijn 1999 5 EG Malti Maltese IEI Integration Corp jiddikjara li dan prodott jikkonforma mal htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid Dirrettiva 1999 5 EC Magyar Hungarian IEI Integration Corp nyilatkozom hogy a berendez s megfelel a vonatkoz alapvet k vetelm nyeknek s az 1999 5 EC ir nyelv egy b el r sainak Polski Polish IEI Integration Corp o wiadcza ze wyrobu jest zgodny z zasadniczymi wymogami oraz pozosta ymi stosownymi postanowieniami Dyrektywy 1999 5 EC Portugu s Portuguese IEI Integration Corp declara que este equipamento est conforme com os requisitos essenciais e outras disposi es da Directiva 1999 5 CE SBOX 100 QM87i Fanless Marine Computer m e Integration Corp Romana Romanian IEI Integration Corp declar ca acest echipament este in conformitate cu cerin ele esentiale si cu celelalte prevederi relevante ale Directivei 1999 5 CE Slovensko Slovenian IEI Integration Corp izjavlja da je ta opreme v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolocili direktive 1999 5 ES Slovensky Slovak IEI Integration Corp t mto vyhlasuje Ze zariadenia sp a z kladn po iadavky a v etky pr slu n ustanovenia Smernice 1999 5 ES Suomi Finnish IEI Integration Corp vakuuttaa t ten ett laitteet on direktiivin 1999 5 EY oleellisten vaatimusten ja sita koskevien direk
50. e systems The SBOX 100 QM87i supports IPMI 2 0 through the optional iRIS 2400 module The SBOX 100 QMS8 i has five serial ports including four RS 232 422 485 serial ports on the front panel and one RS 232 serial port on the rear panel The HDMI DVI D and VGA connectors allow the 100 to support various display devices Other slots and connectors include half size and full size PCle Mini card slots Gigabit Ethernet USB 2 0 ports USB 3 0 ports and audio jacks line in line out and mic in 1 2 Features The SBOX 100 QM87i has the following features Fanless design 2 7 GHz Intel Core 15 4400 CPU supported Intel QM87 chipset Two 2 5 SATA 6Gb s SSD bays One CFast card supported Two bus 2 0B connectors Two GbE LAN for high speed network applications SBOX 100 QM87i Fanless Marine Computer Integration Corp Supports multiple display interfaces including one HDMI connector one DVI D connector and one VGA connector Two USB 3 0 ports and two USB 2 0 ports Four RS 232 422 485 and RS 232 DB 9 serial ports Three audio jacks line out line in and mic in ROHS compliant design 1 3 Front Panel The front panel of the SBOX 100 QM87i provides access to the following external connectors and LED indicators 4x RS 232 422 485 serial port 1 Power LED indicator on green off amber 1 HDD CFast card LED indicator active
51. el attached to the back of the SBOX 100 QM87i 3 1 1 High Surface Temperature WARNING Some surfaces of the equipment may become hot during operation The surface temperature may be up to several tens of degrees hotter than the ambient temperature Under these circumstances the equipment needs to be protected against accidental contact SBOX 100 QM87i Fanless Marine Computer The equipment is intended for installation ina RESTRICTED ACCESS LOCATION Access can only be gained by SERVICE PERSONS by USERS who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken Access is through the use of a TOOL or lock and key or other means of security and is controlled by the authority responsible for the location 3 2 CFast Card Installation The SBOX 100 QM8 7i series has CFast card slot the rear panel To install the CFast card into the system please follow the steps below Step 1 Locate the CFast card slot on the rear panel Remove the CFast slot cover retention screw on the rear panel Figure 3 1 Figure 3 1 CFast Slot Cover Retention Screw Step 2 Remove the slot cover and insert a CFast card into the slot Figure 3 2 Figure 3 2 CFast Card Installation S ia m e 3 Integrakian x Corp SBOX 100 QM87i Fanless Marine Computer Step 3 Secure the CFast card wit
52. er sie iWDD H M Monitor Change Opt super j p General Help Serial Port Console Redirection p Previous Values TET Mee F3 Cio oUm eol Deren F4 Save amp Exit Io eo are Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 2 Advanced V Y Y Y Y Y Y Y Y Y Y Y a ame Integration ET a Corp SBOX 100 QM87i Fanless Marine Computer 4 3 1 ACPI Settings The ACPI Settings menu BIOS Menu 3 configures the Advanced Configuration and Power Interface ACPI options Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced ACPI Settings Select ACPI sleep state the system will enter ACPI Sleep State only CPU Stop 1 1 when ene SUSPEND bi t OD 15 pressed 2 Select Screen 7 Select Item EnterSelect Change F1 General Help EZ Previous Values F3 Optimized Defaults 4 Save Version 2 15 1236 Copyright 2012 American Megatrends Inc BIOS Menu 3 ACPI Configuration ACPI Sleep State 51 only CPU Stop Clock Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used gt si only CPU Stop DEFAULT The system enters S1 POS sleep state The Clock system appears off The CPU is stopped RAM is refreshed the system is running in a low power mode gt 53 only Suspend The caches are flushed and the CPU
53. erver Mgmt Changes BMC network configuration The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above Page 28 4 2 Main The Main BIOS menu BIOS Menu 1 appears when the BIOS Setup program is entered SBOX 100 QM87i Fanless Marine Computer The Main menu gives an overview of the basic system information Setup Copyright PE Chipset Advanced BIOG IN ormat ion BIOO ndor Core Version Compliency Project Version Build Date iWDD Vender iWDD Version IPMI Module Processor Information Name Fi 20000 Grill Processor Stepping Number of Processors Microcode Revision GT Info IGF VBIOS Version Memory RC Version Total Memory Memor Gece mer PCH Information Name PCH Stepping LAN PHY Revision ME FW Version ME Firmware SKU SPI Clock Frequency Security Save amp Exit American Megatrends 4 6 5 4 H772AR12 ROM lel BIO D Im N A Haswell Coro Th 3200 Miz 910 595 CO PE Ome sy s 16 5712 15 440 800 MHz 2 155 ore 4096 MB 1600 Mhz DDR3 LynxPoint 7 8 eA A3 l OIC 5MB Unsupported Read Status Clock Frequency 50 MHz Write Status Clock Frequency 50 MHz Fast Read Status Clock Frequency J T on comet pyri
54. h the slot cover by fastening the previously removed retention screw 3 3 HDD Installation The SBOX 100 QM87i has two 2 5 HDD bays inside the bottom cover To install HDDs follow the steps below Step 1 Remove the bottom cover by removing the 11 retention screws on the bottom panel See Figure 3 3 Figure 3 3 Bottom Cover Retention Screws Step 2 Locate the HDD brackets inside the bottom cover Remove the four HDD bracket retention screws of one of the HDD brackets and lift the HDD bracket Figure 3 4 HDD Bracket Retention Screws Integration Corp SBOX 100 QM87i Fanless Marine Computer Step 3 Insert an HDD into the bracket until the HDD is firmly connected with the SATA cable connector Secure the HDD to the bracket using four retention screws two screws on each side See Figure 3 5 Figure 3 5 Inserting the HDD Step 4 Install the HDD bracket the same position it was before Figure 3 6 Installing the HDD Step 5 Repeat the steps described above to install another HDD if necessary Step 6 Connect the SATA cables and the SATA power cables to the motherboard Step 7 Reinstall the bottom cover with the previously removed retention screws Integratio SBOX 100 QM87i Fanless Marine Computer 3 4 AT ATX Mode Selection and ATX power modes can both be used on the SBOX 100 QM87i panel PC The selection is m
55. hat the notch in the middle of the SO DIMM must be aligned with the plastic bridge in the socket Figure 5 3 Step 6 Press the SO DIMM down until the arms of the SO DIMM socket clip into place and secure the SO DIMM in the socket Figure 5 3 Figure 5 3 SO DIMM Installation Step 7 Place the heatsink and use a cable tie to secure the heatsink with the SO DIMM Step 8 Reinstall the bottom cover SBOX 100 QM87i Fanless Marine Computer Chapter 6 Interface Connectors Page 68 2 e Integration Corp SBOX 100 QM87i Fanless Marine Computer 6 1 Peripheral Interface Connectors The SBOX 100 QM87i motherboard comes with a number of peripheral interface connectors and configuration jumpers The connector locations are shown in Figure 6 1 and Figure 6 2 The Pin 1 locations of the on board connectors are also indicated in the diagrams below The connector pinouts for these connectors are listed in the following sections m a COM5 CON 4 M3 C O i M2 S_ATA2 SATA_PWR2 5 1 SATA_PWR1 4 MINI PCIE1 1 F_PANEL1 AUDIO1 PWR_BTN1 m IPMI m 5 lt lt 5 S gt o9 o zd is 2 z gt gt lt Q Figure 6 1 Main Board Layout Diagram Front Side SBOX 100 QM87i Fanless Marine Computer 1 L ATXCT Figure 6 2 Main Bo
56. hnology Indicates if Intel VT x Technology is supported by the CPU Intel SMX Technology Indicates if Intel SMX Technology is supported by the CPU 64 bit Indicates if 64 bit OS is supported by the CPU EIST Technology Indicates if EIST Technology is supported by the CPU L1 Data Cache Lists the amount of data storage space on the L1 cache 1 Code Cache Lists the amount of code storage space on L1 cache L2 Cache Lists the amount of storage space on the L2 cache L3 Cache Lists the amount of storage space on the L3 cache gt Hyper threading Disabled Use the Hyper threading option to enable or disable the Intel Hyper Threading gt Disabled DEFAULT Disable Intel Hyper Threading Technology Enabled Enable Intel Hyper Threading Technology Active Processor Cores All Use the Active Processor Cores BIOS option to enable numbers of cores in the processor package DEFAULT Enable all cores in the processor package Enable one core in the processor package Integration Corp SBOX 100 QM87i Fanless Marine Computer gt Intel Virtualization Technology Disabled Use the Intel Virtualization Technology option to enable or disable virtualization on the system When combined with third party software Intel Virtualization technology allows several OSs to run on the same system at the same time gt Disabled DEFAULT Disable Intel Virtualization Technology gt Enabled Enable Intel
57. ill nor any BMC network parameters during BIOS phase 32300 DEL EnterSelect Ope General Help F2 Previous Values Optimized Defaults 4 Gave F ER 2012 American Megatrends Inc Use the Configuration Address source option to configure LAN channel parameters statically or dynamically by BIOS or BMC Choosing the Unspecified option will not modify any BMC network parameters during BIOS phase The following options are available Unspecified DEFAULT Static Dynamic Obtained by BMC Dynamic Loaded by BIOS running other Protocol SBOX 100 QM87i Fanless Marine Computer Chapter Maintenance Page 64 SBOX 100 QM87i Fanless Marine Computer WARNING Take Anti Static precautions whenever maintenance is being carried out on the system components Failure to take anti static precautions can cause permanent system damage For more details on anti static precautions please refer to Section 2 1 5 1 System Maintenance Overview When doing maintenance operations on the system please follow the instructions in this chapter Failure to follow these instructions may lead to personal injury and system damage To preserve the working integrity of the SBOX 100 QM87i the system must be properly maintained internal components need replacement the proper maintenance pro
58. ions WARNING Failure to take ESD precautions during the installation of the SBOX 100 QM87i may result in permanent damage to the SBOX 100 QM87i and severe injury to the user Electrostatic discharge ESD can cause serious damage to electronic components including the SBOX 100 QM87i Dry climates are especially susceptible to ESD It is therefore critical that whenever the 100 8 is opened and any of the electrical components are handled the following anti static precautions are strictly adhered to Wear an anti static wristband Wearing a simple anti static wristband can help to prevent ESD from damaging any electrical component Self grounding Before handling any electrical component touch any grounded conducting material During the time the electrical component is handled frequently touch any conducting materials that are connected to the ground Use an anti static pad When configuring or working with an electrical component place it on an anti static pad This reduces the possibility of ESD damage Only handle the edges of the electrical component When handling the electrical component hold the electrical component by its edges Integration Corp SBOX 100 QM87i Fanless Marine Computer B 1 3 Product Disposal Ad CAUTION Risk of explosion if battery is replaced by and incorrect type Only certified engineers should replace the on board battery Dispose of used ba
59. j BIOS Menu 1 Main nz 2012 American Megatrends 2012 American Megatrends Tac Mon Set the Date Use Tab to switch between Data elements ccn Seren T Select Item EnterSelect dps Change F1 General Help F Previous Values Optimized Defaults 4 Save amp Exit INe 1 EM oe ops W SBOX 100 QM87i Fanless Marine Computer The System Overview field has two user configurable fields System Date xx xx xx Use the System Date option to set the system date Manually enter the day month and year System Time xx xx xx Use the System Time option to set the system time Manually enter the hours minutes and seconds 4 3 Advanced Use the Advanced menu BIOS Menu 2 to configure the CPU and peripheral devices through the following sub menus WARNING Setting the wrong values in the sections below may cause the system to malfunction Make sure that the settings made are compatible with the hardware Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced Boot Security Save amp Exit Server Mgmt ACPI Settings System ACPI Parameters RTC Wake Settings Trusted Computing OnT L iom GATA Configuration Intel R Rapid Start Technology Selec AMT Configuration T Select Item Om ron Pip
60. me the board is handled frequently touch any conducting materials that are connected to the ground Use an anti static pad When configuring SBOX 100 QM87i place it on an anti static pad This reduces the possibility of ESD damaging the SBOX 100 QM87i 2 2 Unpacking Precautions When SBOX 100 QM8 i is unpacked please do the following Follow the anti static precautions outlined in Section 2 1 Make sure the packing box is facing upwards so the SBOX 100 QM87i does not fall out of the box sure all the components shown in Section 2 3 are present Integration SBOX 100 QM87i Fanless Marine Computer 2 3 Unpacking Checklist If some of the components listed in the checklist below are missing please do not proceed with the installation Contact the IEI reseller or vendor you purchased the SBOX 100 QM8 7i from or contact an sales representative directly To contact an IEI sales representative please send an email to sales ieiworld com The 5 100 8 7 is shipped with the following components Qm wwe SBOX 100 QM87i marine computer Keyboard and mouse Y cable P N 32006 000300 100 RS Screws for foot pad installation Screws silver Foot pads Driver and manual CD SBOX 100 QM87i Fanless Marine Computer One Key Recovery CD Table 2 1 Package List Contents SBOX 100 QM87i Fanless Marine Computer Chapter
61. minal block 150 W DC input ATX power supply module preinstalled mmm won Operation Vibration IEC 60945 and DNV 2 4 compliant CE FCC Safety DVN IEC 60945 4th IACS E10 IEC 61174 compliant Table 1 1 Technical Specifications SBOX 100 QM87i Fanless Marine Computer 1 6 Dimensions The physical dimensions of the SBOX 100 QM87i are shown in Figure 1 4 BACK VIEW LEFT RIGHT VIEW FRONT VIEW EEN Figure 1 4 SBOX 100 QM87i Dimensions mm SBOX 100 QM87i Fanless Marine Computer Chapter 2 Unpacking An SBOX 100 QM87i Fanless Marine Computer 2 1 Anti static Precautions WARNING Failure to take ESD precautions during installation may result in permanent damage to the SBOX 100 QM8 7i and severe injury to the user Electrostatic discharge ESD can cause serious damage to electronic components including the SBOX 100 QM87i Dry climates are especially susceptible to ESD It is therefore critical that whenever the SBOX 100 QM87i or any other electrical component is handled the following anti static precautions are strictly adhered to Wear an anti static wristband Wearing a simple anti static wristband can help to prevent ESD from damaging the board Self grounding Before handling the board touch any grounded conducting material During the ti
62. n DIMM 1 2048 MB DDR3 Select Item EnterSelect Change Opt F1 General Help F2 Previous Values Optimized Defaults 4 Save amp Exit ioo Version 2 15 1236 Copyright 2012 American Megatrends Inc BIOS Menu 20 Memory Configuration 4 5 Boot Use the Boot menu BIOS Menu 21 to configure system boot options Aptio Setup Utility Copyright C 2012 American Megatrends Inc Main Advanced Chipset Security Save amp Exit Server Mgmt poste rigurosa pn Select the keyboard Bootup NumLock State On NumLock state Outer Boot Enabled Option ROM Messages Force BIOS Launch PXE OpROM Disabled UEFI Boot Disabled O OI Select Item EnterSelect Boote Option Priorities Changes Opt F1 General Help F2 Previous Values IE Optimized Defaults F4 Save amp Exit EO EIS Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 21 Boot m e Integration Corp SBOX 100 QM87i Fanless Marine Computer Bootup NumLock State On Use the Bootup NumLock State BIOS option to specify if the number lock setting must be modified during boot up gt On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up This allows the immediate use of the 10 key numeric keypad located on the right side of the keyboard To confirm this the Number Lock LED light on the keyboard is lit gt
63. nces and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Pb Hg Cd Chromium Biphenyls Diphenyl Ethers CR VI PBB PBDE Printed Circuit Board p p eae nae o p po Power Supply Assemblies m qp p p e O This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below the limit requirement in SJ T11363 2006 X This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part is above the limit requirement in SJ T11363 2006 Page 102 Integration Corp SBOX 100 QM87i Fanless Marine Computer HEHE E ERRAT RAHE ROHS RE gt ches ae rE RoHS ASP Eh HERR OB TEE Hcet rt TEAS ATLA EFEK BEA SOUS TUNES s o S9 s p 270 O TATA IE A REESE SJ T11363 2006 X VERDE SJ T11363 2006 tr HEALEY ER 103
64. ntegration Corp SBOX 100 QM87i Fanless Marine Computer gt Yes On Erase system event log on every reset every reset When SEL is Full Do Nothing Use the When SEL is Full option to select an reaction to a full SEL gt DoNothing DEFAULT anything when SEL is full gt Erase Erase SEL immediately when SEL is full Immediately gt Log EFI Status Codes Both Use the Log EFI Status Codes option to configure how to log Extensible Firmware Interface status codes gt Disabled DEFAULT Disable the logging of status codes gt Both Log both error codes and progress codes gt Error code Log error codes only gt Progress Log progress codes only code SBOX 100 QM87i Fanless Marine Computer 4 8 2 BMC Network Configuration ia 8 LN EM JE 1 Integration Use the BMC Network Configuration menu BIOS Menu 26 to configure the BMC network parameters Setup Copyright BMC network configuration Lan channel 1 Configuration Address source Unspecified Station IP address Subnet mask Station MAC address Router IP address Router MAC address Vereton 4 15 1206 120 BIOS Menu 26 BMC Network Configuration Configuration Address source Unspecified 2012 American Megatrends Inc Server Mgmt Select to configure LAN channel parameters ua or dynamically Dy se O Unspecified option W
65. nts when vacuuming the SBOX 100 QM87i Turn the SBOX 100 QM87i off before cleaning the SBOX 100 QM87i Never drop any objects or liquids through the openings of the SBOX 100 QM87i Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the SBOX 100 QM87i Avoid eating drinking and smoking within vicinity of the SBOX 100 QM87i B 2 2 Cleaning Tools Some components in SBOX 100 QM87i may only be cleaned using a product specifically designed for the purpose In such case the product will be explicitly mentioned in the cleaning tips Below is a list of items to use when cleaning the SBOX 100 QM87i Cloth Although paper towels or tissues can be used a soft clean piece of cloth is recommended when cleaning the SBOX 100 QM87i Water or rubbing alcohol A cloth moistened with water or rubbing alcohol can be used to clean the SBOX 100 QM87Ti Using solvents The use of solvents is not recommended when cleaning the SBOX 100 QM87i as they may damage the plastic parts Vacuum cleaner Using a vacuum specifically designed for computers is one of the best methods of cleaning the SBOX 100 QM87i Dust and dirt can restrict the airflow in the SBOX 100 QM87i and cause its circuitry to corrode Cotton swabs Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas Foam swabs Whenever possible it is best to use lint free swabs such as foam swa
66. ology Supported Intel VT x Technology Supported Intel SMX Technology Supported 64 bit Supported EIST Technology Supported L1 Data Cache BA IKI o 2 11 Code Cache 22 kB 2 L2 Cache 2506 Ile 2 L3 Cache 20 MEE Hyper threading Enbaled Active Processor cores All Intel Virtualization Technolog Disabled BIS Enabled Joie T I Uomo Disabled Enable for Windows XP and Linux CS optimized ror Hyper Threading Technology andDisabled fOr Otlier 105 nol optimized for Hyper Threading Technology When Disabled only one thread per enabled core is enabled Serecn 7 Select Item EnterSelect Use cS EL General Help F2 Previous Values F3 Optimized Defaults 4 Save 6 Exit ESC Exit Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 6 CPU Configuration The CPU Configuration menu BIOS Menu 6 lists the following CPU details Processor Type Lists the brand name of the CPU being used SBOX 100 QM87i Fanless Marine Computer 2 e Integration Corp CPU Signature Lists the CPU signature value Microcode Patch Lists the microcode patch being used Max CPU Speed Lists the maximum CPU processing speed Min CPU Speed Lists the minimum CPU processing speed CPU Speed Lists the CPU processing speed Processor Cores Lists the number of the processor core Intel HT Technology Indicates if Intel HT Technology is supported by the CPU Intel VT x Tec
67. omputing menu BIOS Menu 5 to configure settings related to the Trusted Computing Group TCG Trusted Platform Module TPM Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced Enables Disables BIOs Security Device Support Disable Support for security device O S will nort show Security Device Current Status Information PET O Mic NO Security Device Found INTIA interface will not be available 230 j ores Select Item Enterselect Change Opt General Help F2 Previous Values Optimized Defaults F4 Sene ES Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 5 Trusted Computing EJ E Integration Corp Security Device Support Disable SBOX 100 QM87i Fanless Marine Computer Use the Security Device Support option to configure support for the security devices gt Disable DEFAULT Security device support is disabled gt Enable Security device support is enabled 4 3 4 CPU Configuration Use the CPU Configuration menu BIOS Menu 6 to view detailed CPU specifications and configure the CPU Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced CPU Core TM 15 4400E CPU Q 2 DG CPU Signature Microcode Patch le Max CPU Speed 2100 MHz Min CPU Speed 800 MHz CPU Speed 3200 MHz Processor Cores 2 Intel HT Techn
68. ous Values Optimized Defaults oave EE Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 15 IEI Feature gt Auto Recovery Function Disabled Use the Auto Recovery Function BIOS option to enable or disable the auto recovery function of the IEI One Key Recovery gt Disabled DEFAULT Auto recovery function disabled gt Enabled Auto recovery function enabled ia l Corp PT En integration SBOX 100 QM87i Fanless Marine Computer 4 4 Chipset Use the Chipset menu BIOS Menu 16 to configure the system chipset Aptio Setup Utility Copyright C 2012 American Megatrends Inc Main Chipset Boot Security Exit Server Mgmt PCH ij PCH Parameters gt System Agent SA Configuration lt gt j Select Item EnterSelect F General Help F2 Previous Values Optimized Defaults 4 Save amp Exit oC Version 2 15 1236 Copyright 2012 American Megatrends Inc BIOS Menu 16 Chipset 4 4 1 PCH IO Configuration Use the PCH IO Configuration menu BIOS Menu 17 to configure the PCH IO chipset Aptio Setup Utility Copyright C 2012 American Megatrends Inc Chipset Auto Power Button Status Disable ATX Control Detection of the Azalia device Azalia HD Audio Enabled Disabled Azalia will be Serial IRQ Mode Continuous unconditionally disabled
69. rial Port 3 Configuration gt Serial Port Enabled Use the Serial Port option to enable or disable the serial port gt Disabled Disable the serial port Enabled DEFAULT Enable the serial port gt Change Settings Auto Use the Change Settings option to change the serial port IO port address and interrupt address gt Auto DEFAULT The serial port IO port address and interrupt address are automatically detected gt lO 3E8h Serial Port I O port address is 3E8h the interrupt IRQ 11 address is IRQ11 gt IO 3E8h Serial Port I O port address is 3E8h the interrupt IRQ 10 11 address is IRQ10 11 gt IO 2E8h Serial Port I O port address is 2E8h and the interrupt IRQ 10 11 address is IRQ10 11 SBOX 100 QM87i Fanless Marine Computer gt IO 2D0h Serial Port I O port address is 2D0h and the interrupt IRQ 10 11 address is IRQ10 11 gt IO 2D8h Serial Port I O port address is 2D8h and the interrupt IRQ 10 11 address is IRQ10 11 Serial Port Mode RS485 Use the Serial Port Mode option to set the Serial Port 3 signaling mode 5232 Configure Serial Port 3 as RS 232 gt RS422 Configure Serial Port 3 as RS 422 gt RS485 DEFAULT Configure Serial Port 3 as RS 485 4 3 10 1 4 Serial Port 4 Configuration Serial Port Enabled Use the Serial Port option to enable or disable the serial port gt Disabled Disable the serial port Enabled DEFAULT Enable the serial port gt
70. s gt Disabled Disable the on board SATA controller s SATA Mode Selection IDE Use the SATA Mode Selection option to determine how SATA devices operate gt IDE DEFAULT Configures SATA devices as normal IDE device gt AHCI Configures SATA devices as AHCI device gt RAID Configures SATA devices as RAID device SBOX 100 QM87i Fanless Marine Computer 4 3 6 Intel Rapid Start Technology The Intel Rapid Start Technology menu BIOS Menu 8 configures Intel Rapid Start Technology Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced Intel R Rapid Start Technology Disabled Enable or disable Intel R Rapid stare Technology lt Select Screen Select Item EnterSelect Change General Help F2 Previous Values FS Optimized Defaults F4 Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 8 Intel Rapid Start Technology Intel R Rapid Start Technology Disabled Use the Intel R Rapid Start Technology option to disable or enable Intel Rapid Start Technology gt Disabled DEFAULT Intel Rapid Start Technology is disabled Enabled Intel amp Rapid Start Technology is enabled ia LN Ee integrotion SBOX 100 QM87i Fanless Marine Computer 4 3 7 AMT Configuration The AMT Configuration menu BIOS Menu 9 allows advanced power management options to be
71. stallation J pais U 67 Figure 6 1 Main Board Layout Diagram Front Side 69 Figure 6 2 Main Board Layout Diagram Solder Side 70 Page VIII SBOX 100 QM87i Fanless Marine Computer List of Tables Table 1 1 Technical Specifications Ri CREE RUIN DN 6 Table 2 1 Package List Contents xa DD J J J 11 Table 3 1 RS 232 Serial Port COM1 Pinouts 19 Table 3 2 RS 232 422 485 Serial Port Pinouts J nennen 19 Table 3 3 CAN Bus Connector Pinouts nnn nana nnns 20 Table 3 4 CAN Bus Jumper Settings nean J Q J J 21 Table 4 1 BIOS Navigation Keys EDU EN 28 Table 6 1 Peripheral Interface Connectors J J J 72 Table 6 2 Audio Connector AUDIO1 Pinouts
72. sword If ONLY the Administrator s password is set then wiles only limits access Sauls and 15 only asked for when entering Setup If ONLY the User s password is set then this Css Selec Screen is a power on password and must be entered to il Select Item boot or enter Setup In Setup the User will EnterSelect have Administrator rights Change Opt The password length must be General Help in the following range Previous values Minimum length Optimized Defaults Maximum length Save n Exit Administrator Password User Password Version 2 15 1236 Copyright C 2012 American Megatrends Inc BIOS Menu 22 Security Administrator Password Use the Administrator Password to set or change a administrator password Page 58 ia Integration Corp 2 SBOX 100 QM87i Fanless Marine Computer User Password Use the User Password to set or change a user password 4 7 Save amp Exit Use the Save amp Exit menu BIOS Menu 23 to load default BIOS values optimal failsafe values and to save configuration changes Aptio Setup Utility Copyright C 2012 American Megatrends Inc Main Advanced Chipset BOOT Save amp Exit Save Changes and Reset Reset the system after Discard Changes and Reset saving the changes Restore Defaults Save as User Defaults Restore User Defaults zz o laoa Select Item EnterSelect e Ch
73. tation Signal PWM Control Signal Table 6 7 Fan Connector CPU 1 Pinouts SBOX 100 QM87i Fanless Marine Computer 6 2 7 Front Panel Connector F_PANEL1 T p _ Emre m mes see e _ aon s _ Table 6 8 Front Panel Connector F PANEL1 Pinouts 6 2 8 IPMI LED Connector IPMI_LED1 DESCRIPTION IPMI_LED IPMI LED Table 6 9 IPMI LED Connector LED1 Pinouts 6 2 9 LAN Active LED Connector LAN ACT LED1 DESCRIPTION IPNNO DESCRIPTION LAN1 LINK ACT V 3P3 LAN Table 6 10 LAN Active LED Connector LAN ACT LED1 6 2 10 PCle Mini Slots MINI PCIE1 MINI PCIE2 Table 6 11 PCle Mini Slots MINI PCIE1 MINI PCIE2 Pinouts 6 2 11 Power Connector PWR1 Table 6 12 Power Connector PWR1 Pinouts PWRBTN SW Table 6 13 Power Button Connector PWR_BTN1 Pinouts 6 2 13 5 Connector 5 1 5VSB EC_PSON Table 6 14 PS ON Connector PS 1 Pinouts 6 2 14 RS 232 422 485 Connector COM2 5 Table 6 15 RS 232 422 485 Connectors COM2 COM3 COM4 5 6 2 15 SATA Connector S ATA1 m e Integration Corp SBOX 100 QM87i Fanless Marine Computer Table 6 16 SATA Connector S_ATA1 Pinouts 6 2 16 SATA Connector 5 2 Table 6 17 SATA Connector S_ATA2 Pinouts 6 2 17 SATA Power Connector SATA Total 5V SATA power
74. ter and try again 4 1 2 Using Setup Use the arrow keys to highlight items press ENTER to select use the PageUp and PageDown keys to change entries press F1 for help and press Esc to quit Navigation keys are described below wm emm Increase the numeric value or make changes SBOX 100 QM87i Fanless Marine Computer Decrease the numeric value or make changes Page Up key Increase the numeric value or make changes Page Dn key Decrease the numeric value or make changes Main Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu Exit current page and return to Main Menu General help only for Status Page Setup Menu and Option Page Setup Menu Load optimized defaults Save changes and Exit BIOS Table 4 1 BIOS Navigation Keys 4 1 3 Getting Help When 1 is pressed small help window describing the appropriate keys to use and the possible selections for the highlighted item appears To exit the Help Window press ESC or the F1 key again 4 1 4 BIOS Menu Bar The menu bar on top of the BIOS screen has the following main items Main Changes the basic system configuration Advanced Changes the advanced system settings Chipset Changes the chipset settings Boot Changes the system boot configuration Security Sets User and Supervisor Passwords Save amp Exit Selects exit options and loads default settings S
75. tiivin muiden ehtojen mukainen Svenska Swedish IEI Integration Corp f rklarar att denna utrustningstyp st r verensst mmelse med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 1999 5 EG Integration SBOX 100 QM87i Fanless Marine Computer FCC WARNING FC This equipment complies with Part 15 of the FCC Rules Operation is subject to the following two conditions m his device may not cause harmful interference and m This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Em _ 3 B intecroktioni Corn qe SBOX 100 QM87i Fanless Marine Computer Weg Appendix B Safety Precautions Page 89
76. time out value time out value is 48 seconds ADD THE APPLICATION PROGRAM HERE CMP JNE MOV MOV INT EXIT EXIT AP 1 W_LOOP AX 6F02H BL 0 15H is the application over No restart the application disable Watchdog Timer IE Integration Corp SBOX 100 QM87i Fanless Marine Computer Appendix Hazardous Materials Disclosure Page 100 m e Integration Corp SBOX 100 QM87i Fanless Marine Computer E 1 Hazardous Material Disclosure Table for IPB Products Certified as ROHS Compliant Under 2002 95 EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China China RoHS standards The table below acknowledges the presences of small quantities of certain materials in the product and is applicable to China ROHS only A label will be placed on each product to indicate the estimated Environmentally Friendly Use Period EFUP This is an estimate of the number of years that these substances would not leak out or undergo abrupt change This product may contain replaceable sub assemblies components which have a shorter EFUP such as batteries and lamps These components will be separately marked Please refer to the table on the next page Page 101 Integration Corp SBOX 100 QM87i Fanless Marine Computer Part Name Toxic or Hazardous Substa
77. tteries according to instructions and local regulations Outside the European Union If you wish to dispose of used electrical and electronic products outside the European Union please contact your local authority so as to comply with the correct disposal method Within the European Union EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors and electrical accessories such as signal cables or power cords When you need to dispose of your display products please follow the guidance of your local authority or ask the shop where you purchased the product The mark on electrical and electronic products only applies to the current European Union Member States Please follow the national guidelines for electrical and electronic product disposal B 2 Maintenance and Cleaning Precautions When maintaining or cleaning the SBOX 100 QM87i please follow the guidelines below B 2 1 Maintenance and Cleaning Prior to cleaning any part or component of the SBOX 100 QM8 7i please read the details below SBOX 100 QM87i Fanless Marine Computer m E e The interior of the SBOX 100 QM87i does not require cleaning Keep fluids away from the SBOX 100 QMS8 i interior Be cautious of all small removable compone
78. u UL Lu a u uu ahua 17 Figure 3 3 Mounting ll li l il ill 17 Figure 3 9 Serial Port Locations J nU cuan Nux U C calda U FAVRE 18 Figure 3 10 CAN Bus Connector J J 20 Figure 3 11 CAN Bus Jumper Locations J J Q J J J 21 Figure 3 12 Power Input Connector Pinouts J Q J J 21 Figure 3 13 Power Connector and Power Button J nnne 22 Figure 3 14 Clear CMOS Button Location J J J J J 22 Figure 3 15 TEL iMAN Web Address J J 24 Figure 3 16 IEI iMAN Web GUI J J J J 25 Figure 5 1 Bottom Cover Retention Screws J J J J l 66 Figure 5 2 SO DIMM Locations J ctas una 66 Figure 5 3 SO DIMM In
79. us ME 3 11 IPMI Setup Procedure The SBOX 100 QM87i with iRIS 2400 module installed features Intelligent Platform Management Interface IPMI that helps lower the overall costs of server management by enabling users to maximize IT resources save time and manage multiple systems The SBOX 100 QM87i supports 2 0 through the optional iRIS 2400 module Follow the steps below to setup IPMI 3 11 1 Managed System Hardware Setup The hardware configuration of the managed system SBOX 100 QM87i is described below Integration Corp SBOX 100 QM87i Fanless Marine Computer Step 1 Make sure the 100 87 is installed with an iRIS 2400 module Step 2 Make sure at least one DDR3 SO DIMM is installed in one of the SO DIMM sockets If multiple SO DIMMs are installed all of the SO DIMMs must be same size same speed and same brand to get the best performance Step 3 Connect an Ethernet cable to the RJ 45 LAN 2 port with iRIS label on the rear panel Figure 1 3 3 11 2 Using the Web GUI To manage client system from a remote console using IEI iMAN Web GUI follow the steps below Step 1 Obtain the IP address of the managed system It is recommended to use the IPMI Tool on the managed system to obtain the IP address To use IPMI Tool to obtain IP address follow the steps below a Copy the Ipmitool exe file to a bootable USB flash drive b Insert the USB flash drive to the SBOX 100

Download Pdf Manuals

Related Search

SBOX 100 QM87i_UMN_v1.00

SBOX-100-QM87i_UMN_v1.00

Contents

Download Pdf Manuals

Related Search

Related Contents