Home

Instructions.

1. a Mitre Box or Mitre Saw 2 Repeat to create two walls 2x R TOP amp BOTTOM RAIL AT 3 3 1 2 1M 14x G 8 2 1 4 WOOD SCREWS 2x R TOP amp BOTTOM RAIL AT 2 2 3 4 67 9CM STEP 3 ATTACH PANEL CLIPS FOR SIDE WALLS yy 1 On a flat surface place P 4x4 Post on its side and position Panel Clipsin Fig 2 locations indicated in Figures 1 and 1A Ensure Panel Clips are oriented as shown in Diagrams 2 Panel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3 8 or 3 49cm away from the side of the post as shown in Fig 2 3 With Panel Clips in place mark screw holes with a pencil and pre drill holes with a 1 8 drill bit Not provided 4 Secure Panel Clips in locations indicated in figure 1 and 1A with S7 8 x 1 1 2 wood screws 1 1 2 Wood Screws 5 Repeat for each post configuration Fig 1A Top View Note Post A has Panel fo l an Clips on two sides NL Fig 1 Fig 1 Front View Side View 36 1 2 92 7cm 2x Le 4x4 POST AT 31 1 4 0 79M 8X PANEL CLIPS 1x 2 4x4 POST AT 45 1 16M 16x G7 8 X 1 1 2 WOOD SCREW STEP 4 ATTACHING POST CAPS 1 Place a Post Cap on each 4x4 Post 2 Secure Post Cap with 2 S7 8 1 1 2 Wood Screws 3x POST CAPS 6X G7 8 1 1 2 WOOD SCREWS 1 Place panel assemblies on posts as shown Fig 1 allowing a 2 gap between the bottom of the post and
2. the bottom edge of the bottom rail on the panel assembly Note Assemble with the help of another adult 2 With a 1 8 drill bit predrill holes as shown in figure 2 3 Fasten the panel assembles to the post and Panel Clips with a S5 1 Pan Head Screw provided in location of circles Fig 1 Posts must be securely installed to support structure Consult local STEP 5 ATTACH WINGS TO POSTS A thes building codes and ground conditions for required footing design It is recommended the structure be secured to existing stone concrete or if N deck Fig 2 Predrill Holes and Fasten with S5 1 Pan Head Screw Fig 1 B 2 5 1cm 2 5 1cm C 8X Gs 10 X 1 PAN SCREWS
3. tighten bolts but A U naai not too tight Do not crush the wood Se eee A a This may create splinters and cause proper location structural damage MATERIAL LIST R ee Top and Bottom Rail 2x 3 3 1 2 1M and 2x 2 2 3 4 67 9CM 0 3 Post Caps 8 Panel Clips 4x4 Posts 1x 45 1 16m and 2x 31 1 4 0 79m 2 Arch Topper E 6 One High X Topper STEP 1 ASSEMBLE PANELS 1 Assemble panel in configuration shown Fig 1 Secure with 2 1 4 screws provided in the direction and location of the arrows Use pre drilled holes when available When pre drilled holes are not available use a 1 8 Drill Bit to drill holes on an angle in the inside of the panel as shown Fig F Ensure Panels are right side up Fig 1A 2 Repeat until two panel assemblies are created Groove kP Skinny Piece ick Piece of Wood of Wood Fig 1A Filler Strips on Bottom of Panel Fig 1 Drill Hole on an Angle 2X ONE ARCH TOPPER 16X 8 2 1 4 WOOD SCREWS 6X ONE HIGH X PANEL STEP 2 ASSEMBLE SIDE WALL Oo 1 Secure R Top and Bottom Rails to Panel Assembly with S4 2 1 4 Wood Screws locations indicated by arrows in the direction of the arrow Fig 2 R Top and Bottom Rails will overhang 1 4 on either side of panel Except with Arch Topper R Top and Bottom Rails may need to be cut to size indicated in material list below It is recommended to use
4. INSTALLATION MANUAL GOO9 CORNER ACCENT YM11539 JAN X E d Yardistry Ltd Forest ON Canada NOG 2L1 ll Free Customer Support 1 888 509 4382 info yardistrystructures com www yardistrystructures com sed 08 24 2011 YA RDISTRY IMPORTANT SAFETY NOTICE Yardistry components are intended for privacy decorative and ornamental use only Product is NOT INTENDED for the following Asafety barrier to prevent unsupervised access to pools hot tubs spas or ponds Safety railings for elevated platforms or decks As load bearing support for a building structure heavy objects or swings Used in structures that trap wind rain or snow that would create extra load on the product Permanent structures may require a building permit As the purchaser and or installer of this product you are advised to consult local planning zoning and building inspection departments for guidance on applicable building codes and or zoning requirements Wood is NOT flame retardant and will burn Grills fire pits and chimneys are a fire hazard if placed too close to a Yardistry structure Consult user s manual of the grill fire pit or chimney for safe distances from combustible materials During installation follow all safety warnings provided with your tools and use OHSA approved safety glasses Some structures may require two or more people to install safely Check for underground utilities before digging or driving stakes into t
5. he ground General Information Wood components are manufactured with Cedar C Lanceolata which is protected with factory applied water based stain Knots small checks cracks and weathering are naturally occurring and do not affect the strength of the product Annual application of a water based water repellent sealant or stain will help reduce weathering and checks Warranty Yardistry Limited products are backed by a 5 year limited lifetime warranty from the date of original retail purchase for manufacturing defects and if installed as per manufacturer s installation instructions Patents Pending Tools Required e Tape Measure e 2 Phillips or Robertson e Safety Glasses e Carpenters Level ells oho CENCE e Adult Helpers e 1 8 Drill Bit e Pencil e Carpenters Square e Standard or Cordless Drill e 8 Step Ladder Keys To Assemble Success This identifies information that requires special Check that set or assembly is properly level attention Improper assembly could lead to an before proceeding unsafe or dangerous condition E Where this is shown 2 or 3 Pre drill 1 8 amp 3 16 Bit ee p p people are required to safely Pre drill a pilot hole complete the step To avoid DA PRN before fastening screw injury or damage to the 8 AG or lag to prevent assembly make sure to get help splitting of wood Tighten Bolts Measure Check that assembly is square Square Distance i i Assembly ai a en This indicates time to

Instructions.

Contents

Download Pdf Manuals

Related Search

Related Contents