Audio Alarm Alarme de Son Alarma Audible
Contents
1. Delete All Sensors and Transmitters Panic button the red key on the top right of the keypad instantly activates the alarm whether the audio alarm is in arm mode or not It will always activates the alarm when the ON light is lit on the audio alarm To arm the audio alarm using the keypad transmitter 1 Enter the current MPIN on the keypad transmitter the MPIN is factory pro grammed with 0 0 0 2 Press B C the ON light on the keypad transmitter will flash and emit a long beep The ARM light on the audio alarm will be on The audio alarm is now armed To disarm the audio alarm or terminate the siren 1 Enter the current MPIN on the keypad transmitter 2 Press the ON light on the keypad transmitter will flash and emit a long beep The ARM light on the audio alarm will be off The audio alarm is now disarmed or the siren is turned off When the audio alarm is on but not armed and a remote sensor is activated the audio alarm will emit one chime beep and the ON light will flash once You may deactivate the chime by pressing Current MPIN C on the keypad transmitter For example if people are using the front door constantly you may choose to turn off the chime sound 10 1 Turn the Audio Alarm off by sliding the switch on the bottom of the Audio Alarm so that the ON light is not lit Press and hold the learn button found on the bottom of the Au2. Panic button When the Audio Alarm is ON the four buttons on the transmitter do the following Panic Button instantly activates the alarm whether the Audio Alarm is in arm mode or not Will always activate the alarm when the ON light is liton the Audio Alarm Button 1 this button will arm the Audio Alarm so that the Audio Alarm will communicate with the sensors and transmitters Button 2 when the system is on but not armed and a remote sensor is activated the Audio Alarm will emit one chime beep Button 2 allows you to activate or deactivate the chime sound For example if people are using the frontdoor constantly you may choose to turn off the chime sound Button 3 when the siren is sounding this button will turn off the siren and disarm the Audio Alarm when the siren is not sounding but the system is armed this button will disarm the Audio Alarm _9 KEYPAD TRANSMITTER When the Keypad Transmitter KP 433 is used in conjuction with the Audio Alarm it functions the same as the Keychain Trans mitter 4B 433A or 4B 434 You are able to arm and disarm the audio alarm activate the siren using the panic button and turn on off the chime mode DELETE SENSORS AND TRANSMITTERS You cannot delete one sensor transmitter from the Audio Alarm at a time You must clear all the sensors and transmitters that are currently communicating with the Audio Alarm then re program the ones you want to keep
3. or outdoors within access to an electrical outlet Be careful that the AC adapter wire doesn t guide rain water to the DC JACK located at the bottom of the Audio Alarm There are two ways to attach the Audio Alarm to the wall Hanging it on two stationary screws 1 Using the template provided insert the two screws into the wall 2 Align the two top keyholes on the triangular tabs located at the back of the Audio Alarm with the screws on the wall 3 Gently push the Audio Alarm on to these two screws 4 Open the small door on the bottom of the Audio Alarm 5 Insert the AC adapter and the antenna in the appropriate holes 6 Close the small door so that the AC adapter and the antenna are running through the appropriate spaces in the door INSTALLATION Screwing the unit to the wall 1 Unscrew the two triangular hanging tabs located at the back of the Audio Alarm 2 Turn them around and slide them back into place so that the two tabs are pointing up and the two keyholes are visible from the front 3 Position the Audio Alarm on the wall and insert the two screws in the two keyholes Do not insert the screws all the way into the wall leave some room on the screw to hang the Audio Alarm Use the template if needed 4 Open the small door on the bottom of the Audio Alarm 5 Insert the AC adapter and the antenna in the appropriate holes 6 Close the small door so that the AC adapter and the antenna are
4. running through the appropriate spaces in the door OPERATION OF THE AUDIO ALARM The Audio Alarm is designed to work with Skylink Security System SC 5 SC10 SC 100 series SC 200 series and all the Skylink sensors transmitters If you are using the Audio Alarm AA 433 to communicate with a Skylink sensor i e door window sensor and not a Skylink Security System you will need a Keychain Transmitter 4B 433A or a Keypad Transmitter KP 433 to arm disarm the Audio Alarm These keychain transmitters are included in the Security System SC 100 and SC 10 you may also purchase these keychain transmitters and keypad transmitter separately Before you can activate the audio alarm using the keychain transmitter or keypad transmitter you must first learn the transmitter to the audio alarm so that they can communicate with each other Program the keychain transmitter to the audio alarm You may program as many as 15 Skylink sensors transmitters to the audio alarm Once any of these sensors transmitters are activated the sensor will senda signal to the audio alarm so that the siren or chime will sound Program sensors transmitters to the Audio Alarm 1 Turn on the Audio Alarm slide the button on the bottom of the unit to ON allow 30 seconds for the Audio Alarm to warm up With only the ON light lit on the Audio Alarm press and hold the learn button located on the bottom of the Audio Alarm 2 While pressing d
5. 27 www skylinkhome com Audio Alarm Alarme de Son Alarma Audible MODEL MODELE MODELO AA 433 PREMISES PROTECTED BY ELECTRONIC SECURITY SYSTEM CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Tel T l phone 800 304 1187 Fax T l copieur 800 286 1320 Email Courrier lectronique P N 101A101 004 JAN 2005 support skylinkhome com US Patent no 6243000B1 Audio Alarm MODEL AA 433 OWNER S MANUAL SKYLINK TECHNOLOGIES INC Your Guide to the Audio Alarm MODEL AA 433 The AA 433 Audio Alam contains all the above items TABLE OF CONTENTS OVE EVV paia 4 PACKAGE CONTENTS muaa i i 4 INSTALLA ii aa 5 6 OPERATION OF THE AUDIO ALARM i 7 DIGAS AND OUND tas eos 8 ACTIVATEDEACTIVATE SYSTEM seria 9 NE A TRANSMITE srta 10 DELETE SENSORS AND 11 BATTRE YMAINTIENANCE on uni 12 ADDITIONAL ACCESSORIES OPTION 13 OVERVIEW The Audio Alarm AA 433 is designed to be used in conjunction with Skylink Security System SC 5 SC 10 SC 100 series SC 200 series and any Skylink sensors transmitters When any of the Skylink Security Systems or sensors transmitters are activated the siren of the audio alarm will sound at 120dB You can also set the audio alarm to chime so that when the sensors transm
6. dditional doors windows Keychain Transmitter 4B 434 The battery life 9 volt alkaline battery is approximately two years if only used Activates Security Control Panel SC 001 instantly for backup by pressing panic button Arm Disarm Security Control Panel SC 001 Reliable design crystal base transmission with microcontroller 12V alkaline battery included Emergency Dialer AD 433S When the alarm is activated the Emergency Dialer automatically sends a preprogrammed voice message to as many as nine different phone numbers If any numbers are busy or there is no answer the Emergency Dialer will go back and redial each number nine times or until there is an answer No need to pay monitoring fees Ideal for home small business Operates by AC adapter with battery back up 18 ADDITIONAL ACCESSORIES Security Control Panel SC 001 Four alarm modes Day Night Away Chime Four zones each zone controls up to 6 decives Reliable design with microcontroller 110dB siren Silent Alarm SW 433 Plugs into any AC outlet then plug light into Silent Alarm unit Light flashes when sensor s transmitter s is are activated Silently alerts occupants including the hearing impaired Vibration Sensor VS 433 Activates Emergency Dialer when vibration is detected attach vibration sensor to valuables stereo system antiques 9V alkaline battery included Water Resista
7. dio Alarm While holding the learn button turn on the Audio Alarm by sliding the switch on the bottom You will hear a long beep followed by a series of short beeps When you hear the short beeps re lease the learn button lt FARN ANTENNA You have now cleared all sensors and transmitters from communicating with the Audio Alarm BATTERY MAINTENANCE ADDITIONAL ACCESSORIES Audio Alarm Battery Additional sensors and transmitters as well as add on accessories are available to work with your security system The Audio Alarm comes equipped with a 9 volt alkaline back up battery in case the electrical power is interrupted for any reason Motion Sensor PS 434A Monitors area in a 110 degree ARC and up to 40 feet away from the sensor 9V alkaline battery included When the Audio Alarm battery is low the LO BATT light goes on To replace the Audio Alarm backup battery 1 Take the Audio Alarm off the wall 2 Turn off the unit and remove the AC adapter Door Window Sensor WT 433 Attaches to all doors windows entrances Add on as many magnetic switch MS 001 as needed 12V alkaline battery included 3 Remove the six screws then take off the back cover 4 Disconnect old battery 5 Connect new battery 6 Replace the back cover and install the six Screws Magnetic Switch Magnet MS 001 Used in conjunction with Door Window Sensor WT 433 Add on for a
8. is being powered by electrical current only the battery is weak and needs to be replaced ARM light on the Audio Alarm is armed and will sound when any sensor is activated ARM light off the Audio Alarm is not armed and will not sound when any sensor is activated however it will respond to any of the buttons on the Keychain Transmitter and the panic button on any of the Security Systems SOUNDS You are able to turn on off the short beep sound made by the Audio Alarm when any of the sensors are activated by pressing button 3 on the Keychain Trans mitter 4B 433A sold separately One long beep occurs when the Audio Alarm is turned on with the button on the bottom of the unit One short beep when a sensor is activated and the Audio Alarm is on but not armed anytime buttons 1 2 or 3 is pressed on the Keychain Trans mitter 4B 433A and the Audio Alarm is on but not armed ACTIVATE AND DEACTIVATE THE SYSTEM Now that the system is installed and the sensors are communicating with the Audio Alarm it is time to learn how to arm and disarm the Audio Alarm The only way to arm and disarm the Audio Alarm is via the Keychain Transmitter and Keypad Control option KEYCHAIN TRANSMITTER 4B 433A OR 4B 434 Activate deactivate the chime sound made when a sensor is activated and the Audio Alarm is not armed Turns off the siren and or disarms the system Arms the system TU
9. itters are activated the alarm will only emit one chime instead of sounding the siren The audio alarm is capable of working with a combination of up to 15 Skylink security systems sensors transmitters i e Door Window Sensor Motion Sensor Temperature Sensor Keychain Transmitter Panic Transmitter etc Refer to the back of this user s manual for more accessories PACKAGE CONTENTS All materials required for installation are included in this package One Audio Alarm AA 433 includes 1 antenna 1 AC adapter 1 9 volt alkaline battery installed One pack of screws and anchors for the Audio Alarm One template Double Sided Tape Warning Stickers Manual Warranty Card INSTALLATION Installation is done using the screws included For your convenience we have also included wall anchors and a template to aid in the installation of the Audio Alarm How to use the template to help in the installation 1 Tape the template to the wall where you would like the Audio Alarm to be 2 Screw part way into the surface where the holes are marked on the tem plate 3 Unscrew the screws and remove the template 4 Screw the Audio Alarm in place where you started the screws We recommend that you install the Audio Alarm first with the double sided tape included and once you are satisfied with the positioning reinstall using the screws INSTALLING THE AUDIO ALARM The Audio Alarm is water resistance so it can be installed indoors
10. nt Panic Button Transmitter PT 434 Activates Security Control Panel and Emergency Dialer by pressing the panic button when under duress Ideal for Seniors Handicapped and Disabled Water resistant carry transmitter all the time Operates using lithium batteries included Keypad Control KP 433 Functions as an external keypad or secondary control location Use the keypad to arm disarm the Audio Alarm AA 433 Eliminates the need to walk through your premises to your Security Systems Control Panel Operates using lithium batteries included _14 ADDITIONAL ACCESSORIES Smoke Sensor SS 433 Detects sound frequencies of existing smoke carbon monoxide alarms Activates Security Control Panel SC 001 or Emergency Dialer AD 433S when the preset sound frequency is detected 9V alkaline battery included Audio Sensor AS 433 Detects alarm sound from existing security system alarm sends signal to Dial Alert Eliminates need for monitoring service 9V alkaline battery included Keychain Transmitter 4B 433A Activates and deactivate the Audio Alarm AA 433 at the push of a button Reliable design with microcontroller 12V alkaline battery included Temperature Sensor TS 433 Monitors temperature of a specific area i e greenhouse horse farms laboratory etc Activates Security Control Panel SC 001 or Emergency Dialer AD 433S when the tempera ture of the monit
11. ored area is above or belowa preset temperature Temperature range OF 19 C to 159 F 69 C Operates using lithium batteries included Flood Sensor FS 433 Place sensor along basement wall near water heater washing machine etc Notifies Security Control Panel SC 001 or Emergency Dialer AD 433S when water is detected 12V alkaline battery included 15
12. own on the button activate the sensors or transmitters that you want to program to the audio alarm i e keychain transmitter If you are programming the keychain transmitter you can activate the transmitter by pressing any one of the buttons If you are programming the keypad transmitter you may activate it by pressing the panic button 3 If a connection has been made the Audio Alarm will stop beeping and make a continuous tone until the black button on the Audio Alarm is released Program control panel SC 001 SC 002 to the Audio Alarm AA 433 a 1 Turn on the Audio Alarm slide the button on the bottom of the unitto ON allow 30 seconds for the Audio Alarm to warm up With only the ON light lit on the Audio Alarm press and hold the learn button located on the bottom of the Audio Alarm 2 While pressing down on the button of the Audio Alarm enter the current MPIN Master Personal Identification Number on the Security Control Panel SC001 SC002 3 Press B B on the Security Control Panel 4 If a connection has been made the Audio Alarm will stop beeping and make a continous tone until the learn button on the Audio Alarm is released LIGHTS AND SOUNDS LIGHTS ATP ON light lit power is being sent to the Audio Alarm ALL BELOW SCENARIOS INCLUDE THE ON LIGHT LIT LO BATT light off the Audio Alarm is being powered by electrical current and or the battery LO BATT light on the Audio Alarm
Download Pdf Manuals
Related Search