USER`S MANUAL Alpha-4L Series Direct Thermal Portable Bar
Contents
1. 2 3 Operator Control 2 3 1 LED Indication and Keys Press and hold for 2 3 seconds to turn on the printer Press and hold for 2 3 seconds to turn off the printer Ready status Feed one label Printing status Pause the print job Full charged eaten Salle 2 3 charged level Green solid 1 3 charged level Green blinking Low battery Amber solid Battery is charging NN olid Bluetooth device is ready i Blue blinking Bluetooth device is communicating solid WiFi device is ready Blue blinking WiFi device is communicating Note WiFi device is optional Green blinking Amber solid 10 2 3 2 LED Indication and Keys for LCD Option eys M Enter the printer setting menu Button for LCD setting menu Press and hold for 2 3 seconds to turn on the printer Press and hold for 2 3 seconds to turn off the printer Button for LCD setting menu Ready status Feed one label Printing status Pause the print job Button for LCD setting menu LEDs Status Indication M3 Ott Printer is ready Display the printer information Button for LCD setting menu Media cover is open Off Out of memory R eae Clean data Printer is busy a No paper R link Printer power is turned off Printer power is turned on Battery is full charged Green blinking Low battery Amber solid Battery is charging CS indication Printer has been connected with cable Bluetooth devices have been pair2. PIN Code Item Description Defaut BT SPP Local Name This item is used to set the local name for Bluetooth This item is used to set the local PIN code for PIN Code Bluetooth 0000 6 3 6 Date Time Main Menu Date Time nee er Date This item is used to set the date ex 2019 05 80 item is used to set the date ex 2013 05 This tem is used to set the date ex 2013 05 30 This item is used to set the time ex 19 20 02 48 6 3 7 Display Always On Always Off 5 Seconds 10 Second Contrast 30 Second Backlight 1 Minute Main Menu Setup Display 5 Minutes 10 Minutes 30 Minutes 1 Hour 5 Hours u names CU en contrast contrast Ths item is used to set the contrast for This item is used to set the contrast for display Backlight This item is used to set the backlight time for display 10 Seconds 49 6 4 File Manager This feature is used to check the printer available memory and file list DRAM Available memory Saved file lis FLASH Available memory Saved file list Main Menu File Manager 07 1 51D Available memory Saved file list tem Description 22 Use this menu to show available memory space and run BAS the files saved in the printer DRAM memory Use this menu to show available memory space and run BAS Fasu the files saved in the printer Flash memory Use this menu to show available memory space and run BAS
3. Please follow the steps below to calibrate the media sensor 1 Turn off the printer power switch 2 Hold on the FEED button el then turn on the power switch 3 Release the power switch when l LED color turn on amber Note In this moment you should still hold on the FEED button 4 The printer will beep sound twice later then release the FEED button El when the indicator becomes and blinking 5 Printer will calibrate the gap black mark sensor sensitivity Note You also can do this function by open close the media cover when turn on the printer The LEDs will be changed as following figures Beep sound twice gt 5 blinks gt 5 blinks gt 5 blinks gt Turn on the printer 4 1 2 Self test and Dump Mode Please follow the steps below 1 Turn off the printer power switch 2 Hold on the FEED button El then turn on the power switch 3 Release the power switch when l LED color turn on amber Note In this moment you should still hold on the FEED button 96 4 The printer will beep sound twice later then release the FEED button El when the indicator becomes and blinking 5 Printer will calibrate the sensor and print out the internal settings then enter the dump mode Note Turn off on the power or press FEED button to resume printer from dump mode to normal printing mode Please refer to sections 4 3 and 4 4 for more details of self test and dump mode mE The LEDs
4. 1 battery charger station Charging capability 1 4 Print Specifications Print Specifications Print head resolution 203 dots inch 8 dots mm dots per inch mm Printing method Direct thermal Dot size 0 125 x 0 125 mm width x length 1 mm 8 dots Print speed Max 4 ips 100 mm sec inches per second 2 3 Ips for peeler mode Max print width 4 09 104 mm Max print length 90 2286 mm Vertical 1 mm max Printout bias Horizontal 1 mm max 1 5 Media Specifications Media Specifications Media roll capacity Max 2 65 67 3 mm OD Media core diameter 12 7 mm 25 4 mm 0 5 1 ID core Mediatype Continuous die cut black mark External fan yP fold receipt Linerless label w linerless kit Media wound type Outside wound Media width 50 8 mm 112 mm Media thickness 0 055 mm 0 165 mm Label length 12 7 mm 2286 mm Label length peeler mode 25 4 152 4 mm 1 6 Stack height 70 mm 2 75 Page length 152 mm 305 mm 6 12 Black mark Min 8 mm W x 2 mm H OT External fan fold media 2 Operations Overview 2 1 Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping Please carefully inspect the packaging and printer upon receiving the bar code printer Please retain the packaging materials in case you need to reship the printer Unpacking the printer the following items are included in the ca
5. Density from 0 to 30 and the step is 1 You may need to adjust your density based on selected media Use this item to setup print soeed The each increase or decrease Print Speed is 1 ips Available setting is from 1 to 6 This item is used to fine tune media stop location Available Tear Or setting value is from to or 0 to 9 This item is used to set the print mode There are 2 modes as below Print mode Printer Mode Tear Off Next label top of form is aligned to the print Mode head burn line location Peeler Mode Enable the label peel off mode Print Width W item is used to set print width The available value is from 0 List Fonts This feature is used to print current printer available fonts list to N A en optional memory card This feature is used to print current printer available images list to the label The images stored in the printers DRAM Flash or optional memory card This feature is used to print current printer available formats list to the label The formats stored in the printer s DRAM Flash or optional memory card Control Prefix This feature is used to set control prefix character Format Prefix This feature is used to set format prefix character Delimiter Char This feature is used to set delimiter character This option is used to set the action of the media when you turn on the printer Media Power Up determine length and feed label Length Printer determine length
6. FEED button el when LCD showing Self Test 5 Printer will calibrate the sensor and print out the internal settings then enter the dump mode Note Turn off on the power or press FEED button to resume printer for normal printing Ready mode Please refer to sections 4 3 and 4 4 for more details The LCD will be changed as following figures 29 Beep sound twice gt Calibrate 5 dots gt Self Test 5 dots gt Initialize 5 dots gt Turn on the printer 4 2 3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings to defaults Printer initialization is activated by the following procedures 1 Turn off the printer power switch 2 Hold on the FEED button Es then turn on the power switch 3 Release the power switch when Error LED color turn on red Note In this moment you should still hold on the FEED button 4 The printer will beep sound twice later then release the FEED button El when the LCD showing Initialize 5 Printer will restore printer settings to defaults Note Please refer to section 4 5 for printer defaults m The LCD will be changed as following figures Beep sound twice gt Calibrate 5 dots gt Self Test 5 dots gt Initialize 5 dots gt Turn on the printer 30 4 3 Self test Printer will print the printer configuration after media sensor calibration Self test printout ca
7. WiFi settings information option File management information PHYSICAL DRAM XXXX KBYTES AVAILABLE DRAM XXXX KBYTES FREE PHYSICAL FLASH XXXXX KBYTES AVAILABLE FLASH XXXXX KBYTES FREE END OF FILE LIST RRARARARA RARA RARA RARA RARA RARA KARA A A O HN N INN S Print head test pattern W N ac mh 31 4 4 Dump mode Printer will enter dump mode after printing printer configuration In the dump mode all characters will be printed in 2 columns as following The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters It allows users or engineers to verify and debug the program SPEED 2 0 53 50 45 45 44 20 32 2E 30 0D DENSITY 8 GA 44 45 4E 53 49 54 59 20 38 SET PEEL 0D OA 53 45 54 20 50 45 45 4 OFF DIRE 29 4F 46 46 0D GA 44 49 52 46 CTION A 43 54 49 4F 4E 20 30 OD OA 47 E 30 38 20 6D 6D 20 BA 45 4E 43 45 20 0 0 SET 30 20 30 0D OA 53 45 54 20 43 ASCII Data gt UiTer OFF 58 54 54 48 62 20 F 46 46 o lt Hex decimal data related to left SIZE 190 GA 53 49 54 45 20 31 30 30 E BARCODE 1 DA 42 41 52 43 4F 44 149 39 34 34 20 31 22 28 31 column of ASCII data ET CUTT OD OA 53 45 5 43 55 54 54 ER OFF 51 46 62 20 4F 46 46 OD BA 53 49 ZE 100 02 5A 45 20 31 30 30 2E 30 32 20 mm 656 04 m 60 6D 2C 36 35 2 0 34 20 6D LS BA 6D 0D BA 43 4C 53 OD OA 42 41 ACODE
8. amber of LED indicator will turn to Power green 13 3 3 Loading the Media 3 3 1 Loading the Media 1 Open the printer media cover by pressing the media cover release button 2 Pull the media holders apart to fit the label roll width 3 Place the roll between the media holders and close them onto the core Place the paper printing side face up and pull out enough paper over the print head 14 15 Press each side of media cover to close the media cover and make sure the media cover closed correctly Note Please calibrate the gap black mark sensor when changing media Turn on the printer and open close the media cover then it will calibrate the sensor automatically Please refer to video on TSC YouTube or driver CD 3 3 2 Loading Media in Peel off Mode 1 Please refer to subsection 3 3 1 to loading the media roll into the printer Note Please calibrate the gap black mark sensor after loading media in peel off mode Turn on the printer and open close the media cover then it will calibrate the sensor automatically 2 Remove 1 2 labels from the liner 3 Press each side of media cover to close the media cover and make sure the media cover closed correctly 16 Feed the liner go through the peeler module as figure shown Pull the liner tightly 6 Move the peeler module to near the peeler bar by pushing each side of peeler module
9. and feed label Printer will not move media This option is used to set the action of the media when you close the print head Head Close Printer will advance one label determine length and feed label This option is used to adjust print position vertically on the label CODEN TOR The range is 120 to 120 dots ia This option is used to adjust print position horizontally on the Zeil O SIM N label The range is 9999 to 9999 dots Note If printing from enclosed software driver the software driver will send out the commands which will overwrite the settings set from the panel 44 6 3 2 Sensor Gap Calibration Black Ma Continuous Gap Scan Backing Manual Setup Black Mark gas Scan Mark IQ Remove MEL a Continuou ema Menu Setup Sensor E Threshold Viax mum Fixed Length ON Advanced Min Paper Max Gap Mart tem Description gt gt Default This item is used to set the media sensor type and calibrate the Auto Calibration selected sensor Printer will feed 2 to 3 gap labels to calibrate the sensor sensitivity automatically In case Auto Calibration cannot apply to the media please use Manual Setup function to calibrate the sensor manually Please follow the shown step from LCD to do Manual Setup Note You can open the media cover to move the paper but have to close the media cover for each scan Threshold This item is used to fix the calibrated sensor sensitivity Aut
10. as following Calibrate Self Test Initialize Release FEED Media sensor button for Media sensor calibration calibration self test and Printer initialization Please refer to 4 2 1 enter dump mode Please refer to 4 2 3 Please refer to 4 2 2 different functions 4 2 1 Media Sensor Calibration Please follow the steps below to calibrate the media sensor 1 Turn off the printer power switch 2 Hold on the FEED button Es then turn on the power switch 3 Release the power switch when Error LED color turn on red 98 Note In this moment you should still hold on the FEED button 4 The printer will beep sound twice later then release the FEED button el when LCD showing Calibrate 5 Printer will calibrate the gap black mark sensor sensitivity Note You also can do this function by open close the media cover when turn on the printer m The LCD will be changed as following Beep sound twice gt Calibrate 5 dots gt Self Test 5 dots gt Initialize 5 dots gt Turn on the printer 4 2 2 Self test and Dump Mode Please follow the steps below 1 Turn off the printer power switch 2 Hold on the FEED button El then turn on the power switch 3 Release the power switch when Error LED color turn on red Note In this moment you should still hold on the FEED button 4 The printer will beep sound twice later then release the
11. de PDF 4 17 UPC E EAN and UPC 2 5 digits pise MSI PLESSEY China Post ITF14 MicroPDF417 OR EAN14 Code 11 TELPEN code RSS Ren PLANET Code 49 Deutsche Post GSt Datab Identcode Deutsche Post Leitcode alaba LOGMARS Code page Support for F W 7 0 up Codepage 437 English US Codepage 737 Greek Codepage 850 Latin 1 Codepage 852 Latin 2 Codepage 855 Cyrillic Codepage 857 Turkish Codepage 860 Portuguese Codepage 861 Icelandic Codepage 862 Hebrew Codepage 863 French Canadian Codepage 864 Arabic Codepage 865 Nordic Codepage 866 Russian Codepage 869 Greek 2 Codepage 950 Traditional Chinese Codepage 936 Simplified Chinese Codepage 932 Japanese Codepage 949 Korean Codepage 1250 Latin 2 Codepage 1251 Cyrillic Codepage 1252 Latin 1 Codepage 1253 Greek Codepage 1254 Turkish Codepage 1255 Hebrew Codepage 1256 Arabic Codepage 1257 Baltic Codepage 1258 Vietnam ISO 8859 1 Latin 1 Western European ISO 8859 2 Latin 2 Central European ISO 8859 3 Latin 3 South European ISO 8859 4 Latin 4 North European ISO 8859 5 Cyrillic ISO 8859 6 Arabic ISO 8859 7 Greek ISO 8859 7 Hebrew ISO 8859 9 Turkish ISO 8859 10 Nordic ISO 8859 15 Latin 9 UTF 8 1 2 2 Printer Optional Features The printer offers the following optional features Product option feature User Factory option option 2 LCD Liquid crystal display 128
12. much for purchasing TSC bar code printer Enjoy TSC s reputation for cost efficient high durability printers with the Alpha 4L economical receipt printer The Alpha 4L is a comfortable light weight printer capable of working with any mobile receipt printing application where you need quick simple receipts on demand Our Alpha 4L is designed for a rough life inside the IP54 rated environmental case to resist dust and water and with its rubber over mold design prepared to take up to a five foot fall and keep printing These small and light printers can be worn comfortably for a full shift without interfering with the user s tasks Use USB Bluetooth optional 802 11 b g n Wireless or serial to connect to a mobile computer or even a smart phone and produce clear easy to read receipts hour after hour This document provides an easy reference for operating the Alpha 4L The online version of the Programmer s manual or more information can be downloaded from service and support web site as an Adobe Acrobat Reader file To print label formats please refer to the instructions provided with your labeling software if you need to write the custom programs please refer to the TSPL TSPL2 programming manual that can be found on the accessories CD ROM or on TSC website at http www tscprinters com Applications Portable point of sale Retail item marking markdowns shelf labeling amp shelf talkers Labels for shipping amp receivi
13. new media roll DiagTool or LCD shows Out i The media is installed Follow the instructions in loading the of Paper incorrectly media to reinstall the media roll Media sensor is not calibrated Calibrate the media sensor _ Media sensor Is ne set properly Calibrate the media sensor The printer status from Make sure media size is set DiagTool or LCD shows Paper properly Jam Label may be stuck inside the printer mechanism Set media size correcily Remove the stuck label inside the printer mechanism The printer status from LCD shows Strong light Press Peel off sensor can t work in Remove the printer to proper place to FEED to print strong light place print for peer off mode Delete unused files in the memory The max numbers of DRAM is 256 files Can t downloading the file to The max user addressable memory memory FLASH The space of memory is full space of DRAM is 2048KB DRAM CARD The max numbers of file of FLASH is 256 files The max user addressable memory space of FLASH is 14336KB as Reload the supply Clean the print head Clean the platen roller Adjust the print density and print speed Run printer self test and check the print head test pattern if there is dot missing in the pattern Change proper media roll Media is loaded incorrectly Dust or adhesive accumulation on the print head Print density is not set pro
14. the files saved in the printer MicroSD card memory 50 6 5 Diagnostics Main Menu Diagnostics Print Config Dump Mode Battery Print Head 6 5 1 Print Config Main Menu Diagnostics Print Config This feature is used to print current printer configuration to the label On the configuration printout there is a print head test pattern which is useful for checking if there is any dot damage on the print head heater element Please refer to section 4 3 for more details 6 5 2 Dump Mode Main Menu BETIS Dump Mode dl Captures the data from the communications port and prints out the data received by printer In the dump mode all characters will be printed in 2 columns Please refer to section 4 4 The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters It allows users or engineers to verify and debug the program Note Dump mode requires 4 wide paper width 51 6 5 3 Battery Main Menu P Diagnostics Battery This feature is used to check the printer battery voltage 6 5 4 Print Head Main Menu Diagnostics Print Head This feature is used to check the printer temperature resistance and bad dots for print head 52 6 6 Language Main Menu Language English This option is used to setup the language on LCD display 6 7 Service Main Menu Service Initialization This feature is used
15. to restore printer settings to defaults Please refer to section 4 5 Note When printer initialization is done please calibrate the gap or black mark sensor before printing 53 7 Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer If the printer still does not function after all suggested solutions have been invoked please contact the Customer Service Department of your purchased reseller or distributor for assistance Possible Cause Recovery Procedure The battery is not properly Reinstall the battery Power indicator does not installed Switch the printer on illuminate Battery out of power Charge the battery The battery is dead Replace a new battery Check if interface cable is well connected to the interface connector Check if wireless or Bluetooth device is well connected between host and printer The port specified in the Windows driver is not correct Aa dede ec Follow the instructions in loading the No print on the label eo pe ope y media IP pap Use thermal type paper The printer status from DiagTool or LCD shows Head The printer carriage is open Please close the print carriage Re connect cable to interface Please reset the wireless device setting Select the correct printer port in the driver Not Printing The printer status from Running out of media roll Supply a
16. to set the WLAN settings 23 3 5 Install the IP54 rated Environmental Case with Shoulder Strap Option 1 Open the case top cover 2 Put the printer into the case 3 Close the case top cover The outside cover should be opened while printing 24 4 Power on Utilities There are three power on utilities to set up and test printer hardware These utilities are activated by pressing FEED button E then turning on the printer power simultaneously and release the button at different positions of LED indicator 4 1 Power on Utility for Standard Panel Please follow the steps below for different power on utilities 1 Turn off the printer power switch 2 Hold on the FEED button E then turn on the power switch 3 Release the power switch when l LED color turn on amber Note In this moment you should still hold on the FEED button 4 The printer will beep sound twice later then release the button El when battery LED indicates with different positions for each function Power on utilities for standard panel The battery LED light will be changed as following 5 cll 5 ELA 5 CET Release FEED Media sensor Media sensor are ua calibration calibration self test Printer initialization and enter dump mode Please refer to 4 1 3 button E for j different functions Please refer to 4 1 1 Please refer to 4 1 2 25 4 1 1 Media Sensor Calibration
17. x 64 pixels resolution w white LED backlight with 4 buttons and 2 LEDs WiFi 802 11 b g n Zebra CPCL emulation language support MO is a Media sensor position position selectable right left center position factory adjustment default center position Linerlesskit D O7 USB cable USB to RS 232 serial converter cable IP54 rated environmental case for standard model oO ff IP54 rated environmental case for linerless model Oo 1 Shoulder strap On DC 7 2V 5800 mAh Li ion rechargeable battery O 12 24VDC automobile cigarette lighter plug O 1 battery charger station 1 3 General Specifications General Specifications ete 160 mm W x 191 6 mm H x 79 mm D imensions Plastic with rubber over molded Weight 0 945 kg w o battery External power adapter Power Input AC 100 240V Output DC 12V 1A Operation 10 50 C 14 122 F Storage 40 60 C 40 140 F Environmental Relative humidity 10 90 non condensing condition IP54 w IP54 rated environmental case Drop 1 5m 5ft Drop 1 8m 6 5ft w IP54 rated environmental case Charging time 5 6 hr Standby mode Bluetooth up to 32 hr Standby mode Wi Fi up to 18 hr Battery Spec Printing one label per 2 minutes Endurance hr 4 x6 Labels Density 3 Internal charging capability battery in Auto switching AC adapter 12 24 VDGC automobile cigarette lighter plug External charging capability battery out
18. 144 62 43 4F 44 46 2 1 34 34 20 11 31 34 39 2 22 3 5 22 20 31 20 1 0 2 6 32 30 26 31 26 30 26 32 20 36 57114387 26 22 35 37 31 31 34 33 38 54 PRINT 1 22 0D QA 60 62 49 4E 54 20 31 1 26 31 0D BA Note 1 Dump mode requires 4 wide paper width 2 Turn off on the power or press FEED button to resume printer for normal printing Ready mode a 4 5 Printer defaults Printer configuration will be restored to defaults as below after initialization Density Bs PrintDirection 0 Gap Offset O Note When printer initialization is done please calibrate the gap or black mark sensor before printing 33 5 Diagnostic Tool TSC s Diagnostic Utility is an integrated tool incorporating features that enable you to explore a printer s settings status change a printer s settings download graphics fonts and firmware create a printer bitmap font and send additional commands to a printer With the aid of this powerful tool you can review printer status and setting in an instant which makes it much easier to troubleshoot problems and other issues 5 1 Start the Diagnostic Tool Features tab 1 Double click on the Diagnostic tool icon to start the software 2 There are four features Printer Configuration File Manager Bitmap Font Manager Command Tool included in the Diagnostic utility 2 Diagnostic Tool 1 50 Language Unit English fe inch C mm Printer Configuration File Manager Bitmap Font Man
19. Alpha 4L Series Direct Thermal Portable Bar Code Printer USER S MANUAL Copyright Information 2013 TSC Auto ID Technology Co Ltd The copyright in this manual the software and firmware in the printer described therein are owned by TSC Auto ID Technology Co Ltd All rights reserved CG Triumvirate is a trademark of Agfa Corporation CG Triumvirate Bold Condensed font is under license from the Monotype Corporation Windows is a registered trademark of Microsoft Corporation All other trademarks are the property of their respective owners Information in this document is subject to change without notice and does not represent a commitment on the part of TSC Auto ID Technology Co No part of this manual may be reproduced or transmitted in any form or by any means for any purpose other than the purchaser s personal use without the expressed written permission of TSC Auto ID Technology Co Agency Compliance and Approvals EN 55022 24 IEC 61000 3 3 IEC 61000 3 2 EN 300328 EN 301489 Part 15B C EN 60950 1 GB 9254 GB 4943 1 GB 17625 1 Wichtige Sicherheits Hinweise 1 Bitte lesen Sie diese Hinweis sorgfaltig durch 2 Heben Sie diese Anleitung fur den spateren Gebrauch auf 3 Vor jedem Reinigen ist das Gerat vom Stromentz zu trennen Verwenden Sie keine Flussig oder Aerosolreiniger Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung 4 Die NetzanschluB Steckd
20. Wi Fi icon will be shown for LCD panel if device has been connected Print out the self test page to confirm if it s connected with right settings 9 Remove the cable to print a data for test Common Z o AS 232 1 Device Type Ce Built in wireless module 2 C External wireless module Built in wireless module a Pr SS WLAN SSID Dlink WLAN Encryption WLAN Key WLAN DHCP CZ lo 0 0 0 lo 0 0 0 0 0 0 0 ww se al ws 37 6 LCD Menu Function Option The Alpha 4L series offer the LCD panel for selection to further enhance its capabilities to meet the demands of a wide range of printing solutions This option feature includes LCD control panel 4 buttons and 2 LED display Please press the M button to enter the setting menu 6 1 How to use the LCD to set the printer Press the M button to display the function menu screen as following shown You can use this 4 buttons to scroll select enter or return the menu depend on the icons from 4 sides of LCD It was selected if the item with the black ground on the screen The icon function is listed as below in Display printer information Enter setting menu Lt Exit setting mode menu Y 38 Enter setting mode For example Change the speed setting please following steps as below 1 Press M button to enter the setting menu Press tJ button to enter the Setup item 2 Press L but
21. ager Command Tool Printer Function Printer Configuration Eme nterface use mE Interface Calibrate Sensor Ethernet Setup ATC Setup Printer Factory Default functions Reset Printer Print Test Page Configuration Page Dump Text Ignore AUTO BAS Exit Line Mode Password Setup Printer Status Printer Status Get Status LPT1 COM 9600 N 8 1 RTS Printer Information Version Cutting Counter 0 0 Check Sum Mileage Em Serial No Common 7 O As 232 Wireless Speed Ribbon Density Ribbon Sensor Paper Width Ribbon Encoder Err Paper Height Code Page Media Sensor Country Code Printer setup Gap i Head up Sensor Gap Offset Reprint After Error Post Print Action Maximum Length Cut Piece Gap Inten Reference Bline Inten Direction Continuous Inten Offset Threshold Detection Shift SRI Clear Load Save Set Get 2012 8 14 FF 06 03 01 34 5 2 Printer Function 1 Connect the printer and computer with a cable Note The printer connects with the computer via USB to USB cable or USB to RS 232 cable option 2 Select the PC interface connected with bar code printer USB to USB cable USB to RS 232 cable Interface Interface LISE Setup 2 The default interface setting is USB interface If USB interface is connected with printer no other settings need to be changed in the interface field 3 Click the Printer Function b
22. cover the platen roller 17 7 Press down the peeler module to lock it Loose the peeler module in the reverse procedures l l l l l l l l l l l l l l l L 18 3 3 3 Loading the Fan fold External Media Open the printer media cover by pressing the media cover release button Pull the media holders apart to fit the media width Push down each side of media holder lock switch to fix the media holder Feed the media through the rear external label entrance chute Place the paper printing side face up 4 Press each side of media cover to close the media cover and make sure the media cover closed correctly Note Please calibrate the gap black mark sensor when changing media Turn on the printer and open close the media cover then it will calibrate the sensor automatically DO 3 3 4 Loading the Linerless Media Option Please refer to subsection 3 3 1 to loading the media roll into the printer Push down each side of media holder lock switch to fix the media holder for using linerless media Place the paper printing side face up and pull out enough paper over the print head Press each side of media cover to close the media cover and make sure the media cover closed correctly Note Please calibrate the gap black mark sensor when changing media Turn on the printer and open close the media cover then it will calibrate the sensor automat
23. ed Green solid MATES Wi Fi device has been connected Battery capacity Note Please refer to the section 6 for more details about LCD 11 3 Setup 3 1 Install the Belt Clip and Battery 1 Insert the belt clip first 2 Insert the left side to install the battery at the rear of the printer 3 Push the right side of the battery Battery safety warning DO NOT throw the battery in fire DO NOT short circuit the contacts DO NOT disassemble the battery DO NOT throw the battery in municipal waste The symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste 12 3 2 Charge the Battery lt takes 5 6 hours to fully charge the battery before the first time usage The lifetime of the battery is 300 times for charge discharge cycles 3 2 1 Charge the Battery 1 The battery is installed into the printer 2 Open the interface cover and plug the power cord to the power jack Plug the power cord into a properly power outlet Note Please switch OFF printer power prior to plug in the power cord to printer power jack When the battery is charging please do not remove the battery from the printer otherwise please re plug the power cord into a power outlet Standard panel 4 When the battery is changing the color of battery status LED indicator is solid amber Note LCD panel option The battery is completely charged and the
24. eneral SPeCCHICALIONS aan 5 APR DECUCA OO oo 5 1 5 Media PECiICa CONS sei 6 3 Operallons IVC 7 2 1 Unpacking and Inspetihar iassisiie ann 7 D 6 A E o E 8 O 8 ARCA M A LEA ESR SOOT A NO anios 9 23 Operator Control ernennen 10 2 3 1 LED Indication and Keys nas 10 2 3 2 LED Indication and Keys for LCD Option 11 DES I cota O 12 ga installthe Belt Clip and Battery sun ea 12 23 2 Charge the Batir oia 13 Se Charsethe Balteiy cas ae ee 13 5 9 Loaline Die Medidas 14 sS Loads the Media isa 14 3 3 2 Loading Media in Peel off Mode ss 16 3 3 3 Loading the Fan fold External Media 19 3 3 4 Loading the Linerless Media Option occcccnnnnnnnnnonononnnononcnonononononananannonononnnnnonos 21 3A Co nneeting the Printer an iia 22 3 4 1 Cable Communications 22228 nn nds diese 22 3 4 2 Wireless Communications with Bluetooth 22 3 4 3 Wireless Communications with Wi Fi Option oo o oococcccccncncnnnnnnnananananononnnnnnnos 23 3 5 Install the IP54 rated Environmental Case with Shoulder Strap Option 24 A POWEL On UUES naci 25 4 1 Power on Utility for Standard Panel ss 25 4 1 1 Media Sensor Calibration oocccccnnnnnnnnnnnnnnnanananonncncnnncnnnnnnnonononananinocncacononanananonononos 26 4 1 2 Selt test and D mp Modern iio 26 4 1 3 Printer TIA IZA CON iii a a a A Ad AA EAN Aia 27 4 2 Power on Uti
25. h printer head by hand If you touch it careless please use ethanol to clean it o Please use 100 Ethenol or Isopropyl Alcohol DO NOT use medical alcohol which may damage the printer head e Regularly clean the print head and supply sensors once change a new media to keep printer performance and extend printer life 56 Revise History Oow mem ee 2013 10 4 Modify section 2 3 2 2013 10 31 Modify section 1 3 and 3 2 57 ISC The Smarter Choice TSC Auto ID Technology Co Ltd Corporate Headquarters 9F No 95 Minquan Rd Xindian Dist New Taipei City 23141 Taiwan R O C TEL 886 2 2218 6789 FAX 886 2 2218 5678 Web site www tscprinters com E mail printer_sales tscprinters com tech_support tscprinters com Li Ze Plant No 35 Sec 2 Ligong 1st Rd Wujie Township Yilan County 26841 Taiwan R O C TEL 886 3 990 6677 FAX 886 3 990 5577
26. ically 21 3 4 Connecting the Printer The printer must establish communication with a host terminal which sends the data to be printed There are three ways to connect for Alpha 4L series By a cable between the printer and its host terminal By a Bluetooth short range radio By a Wireless LAN per 802 1 b g Option 3 4 1 Cable Communications USB connector Printer USB RS 232 connector PC Open the interface cover and connect the printer to the computer smart phone host terminal with USB cable USB to USB or USB to RS 232 3 4 2 Wireless Communications with Bluetooth 1 Turn on the printer 2 Open the Bluetooth device for host terminal to scan for printer s Bluetooth device 3 Connect the Bluetooth devices The Bluetooth LED will turn on blue the Bluetooth icon will be shown for LCD panel if devices have been paired Printer Bluetooth default Address You can find this info from configuration self test page please refer to section 4 for how to print out the self test BT SPP 0000 Note Please refer to section 5 3 to change the name and PIN by DiagTool If your printer supports the LCD please refer the section 6 3 5 to change the name and PIN directly 29 3 4 3 Wireless Communications with Wi Fi Option You should set the WLAN settings via the cable for first using Please refer to section 5 4 to setting the Wi Fi module If your printer supports the LCD please refer the section 6 3 4
27. ing value is either 1 or 0 Use this item to setup the printout direction Direction uorpelld 41 This item is used to set the print mode There are 3 modes as below Printer Mode None Next label top of form is aligned to the print Print mode head burn line location Tear Off Mode Once image is printed completely label Batch Mode gap black mark will be fed to the tear plate location for tear away Peeler Mode Enable the label peel off mode This item is used to fine tune media stop location Available setting value is from to or 0 to 9 This item is used to fine tune print position Available setting value is from to or 0 to 9 This Item is used to set the origin of printer coordinate system horizontally and vertically Available setting value is from 0 to 9 Use this item to set the code page of international character set Use this option to set the country code Note If printing from enclosed software driver the software driver will send out the commands which will overwrite the settings set from the panel 42 6 3 1 2 Printer setup for EPL2 Density Print Speed Tear Off Print Mode Print Width List Fonts List Images Main Menu Setup EPL2 List Formats List Setup Control Prefix Format Prefix Delimiter Char Media Power Ug Head Close Left Position Use this item to setup printing darkness The available setting is
28. ith the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CAUTION Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment RF exposure warning WiFi This equipment must be installed and operated in accordance with provided instructions and must not be co located or operating in conjunction with any other antenna or transmitter End users and installers must be providing with antenna installation instructions and transmitter operating conditions for satisfying RF e
29. lity for LCD Panel Option 28 4 2 1 Media Sensor Calibration ooccccnnnnnnnnnnnnnnnnnnnncnnnocnnnnnnnnnnnononononananinococncncncnnnnnnnnnnnnns 28 4 2 2 Self test and Dump Mode 29 45253 Printer Inia liza cOn diia 30 AS SE I EE E EEN I A OOA I EA E T TTA 31 AA DUMP TOC Cs risa 32 Ac OA O ee ea onu 33 DJ d2eNOSUC TOO enclin es ci 34 5 Lotartine Diasnostie Tool canica 34 52 Printer HUM cOn iaa 35 5 3 Setting Bluetooth by Diagnostic Tool ee esssccceccecccceeessseeececceceeeeeeseeeeceees 36 5 4 Setting Wi Fi by Diagnostic Tool Option ss 37 LCD Ment Funcuon Optom en Gina ei 38 6 1 How to use the LCD to Set the printer 38 622 Ma n Menu OVEIVIEW AA AAA Aa AO OS ED es 41 6 34 Printer Scale 41 6 3 1 1 Printer setup for TSPL2 2222222222222222sssnnnnnnnssssennnnnnnnnnnnnnnnnnnnnnnnnnnenennn 41 6 3 3 2 Printer setup for EPT2 22 2a ul 43 0 3 2 SENSOR ARA AAA 45 6373 Sera COM 2 ee een 46 6 3 4 Wireless LAN ec een 47 0 35 Bluctoo ti ad A A A T 48 6 3 6 Date Me nera I ie dti nou A8 OF BS 0 Et aa en tee AQ GA Eile Manager ssassn aeaea RETA EA A AEE SONORE A ROTAS 50 65 DIIENOSD oras 51 651 PEINE COW S er 51 0 5 2 Dump Mod aonn R E TE Ee 51 6 53 y oea A ee 52 Vil 654 Print Head tiara 52 A SO 53 6 7 DOI VICO RE aAa 53 Te NEOUDICS MOOUILS san 54 A oS Eo a re esse sie 56 Revise USO Vis 57 viil 1 Introduction 1 1 Product Introduction Thank you very
30. n be used to check if there is any dot damage on the heater element printer configurations and available memory space Note Self test printout requires 4 wide paper width PRINTER INFO Model name Version X XX EZ cee ee SERIAL NO A AA Printer model name amp Main board firmware version MILAGE m 2 Printer serial number Printed mileage CHECKSUM 75AC29C E c_ __ SERIAL PORT 9600 N 8 1 Serarecncating ecksum CODE PAGE 850 O7 u Code page COUNTRY CODE 001 _ _ Country code SPEED 2 INCH er Print speed DENSITY 8 80 Print darkness SIZE 4 00 5 9 Label size width height GAP 0 12 0 09 _GapBlack mark vertical gap oe OOOO TRANSPARENCE 6 Battery voltage VOLTAGE 7 05 V Print head temperature TEMPERATURE 31 C Print head average resistance RESISTANCE 179 om 22222 es Bad dots of print head BAD DOT S KR k RH RH eee ee ee ee HH HH AAA ee ee ee ee BT ADDRESS 00190EA07ADD BT NAME BT SPP BT PIN CODE 0000 Ped A A A A e A AR AA AAA HH KH HR KH HR A KU HH RA AR WLAN MAC ADDRESS 00 1D C9 90 FA F4 WLAN MODE INFRASTRUCTURE WLAN SSID WLAN DHCP ENABLED YES WLAN IP ADDRESS 0 0 0 0 WLAN SUBNET MASK 8 0 0 0 WLAN DEFAULT GATEWAY 0 0 0 0 KEKKKKKKRKEKKKRKEKRKRKRKEERREERRERRRREERR FILE LIST DRAM FILE 0 FILE S FLASH FILE 0 FILE S Bluetooth settings information
31. ng Inventory control Cross docking Pick pack amp apply operations Print pick tickets Logistics receipts 1 2 Product Features 1 2 1 Printer Standard Features The printer offers the following standard features Product standard feature Direct thermal printing Black mark reflective sensor center position black mark in back side Gap transmissive sensor Fixed center of offset 2 75 mm to right from center Head open sensor Peeler sensor 2 operation buttons On off and feed 3 LEDs for printer status 3 LEDs for battery status USB 2 0 full speed interface Class 2 Bluetooth 2 1 module 32 MB SDRAM memory 16 MB FLASH memory Micro SD card reader for memory expansion up to SDHC 4G max DC 7 2V 5800 mAh Li ion rechargeable battery Real time clock Powerful 32 bit 200 MHz RISC processor Eltron EPL and Zebra ZPL emulation languages support Internal 8 alpha numeric bitmap fonts Internal Monotype Imaging true type font engine with one CG Triumvirate Bold Condensed scalable font Fonts and bar codes can be printed in any one of the four directions 0 90 180 2 0 degree Downloadable fonts from PC to printer memory Downloadable firmware upgrades Bar code graphics image printing Supported bar code Support for F W 7 0 up 1D bar code BITMAP BMP PCX Code128 subsets A B C Max 256 colors Code128UCC EAN128 Interleave 2 graphics of 5 Code 39 Code 93 EAN 13 ae EAN 8 Codabar POSTNET UPC A Maxico
32. o Maximum Length This item is used to set the max calibrate length EC This item is used for pre printed paper If this advanced function is Advanced turned ON then you can setup the min paper and max gap black mark size 457 6 3 3 Serial Comm 1200 bps 2400 bps y 4800 bps VE 9600 bps N 19200 bps Baud Rate 38400 bps 57600 bps 115200 bps None Main Menu Setup Serial Comm Odd N Even Data Bits Stop Bit s 3 ao a Te Baud Rate Rate This item is used to set the This item is used to set the RS 292 baud rate 232 baud rate 9600 This item is used to set the RS 232 parity None Data Bits This item is used to set the RS 232 Data Bits NN Stop Bit s This item is used to set the RS 232 Stop Bits KM 46 6 3 4 Wireless LAN Infrastructure Operating Mode Ad hoc Main Menu Wireless LAN Scan AP ON DHCP tem Description Default This ttem is used to set the operating mode of wireless local area networks to connect devices to the networks Note Infrastructure mode requires the use of an access point for this communication to take place Ad hoc mode involves connecting a computer directly to another computer Scan AP This item is used to scan the access point devise DHCP This item is used to ON or OFF the DHCP Dynamic Host Configuration Protocol network protocol Operating Mode 47 6 3 5 Bluetooth Local Name Main Menu i Bluetooth
33. onnected with printer no other settings need to be changed in the interface field Select Wireless tab and click on Built in wireless module item Enter the new BT Local Name or BT PIN Code in the editor Press Set button to set the new BT name or BT PIN code of the printer Press Get button to get back the settings Make sure the Bluetooth module settings are set properly AL Common z D As 232 Wireless 4 Device Type f Built in wireless module 2 External wireless module Built in wireless module Bluetooth Local Name lBT 5 PP 3 Bluetooth PIN Code 0000 0 0 0 0 0 0 0 0 0 0 0 0 im m a es 36 5 4 Setting Wi Fi by Diagnostic Tool Option 1 Connect the printer and computer with the cable Note The printer connects with the computer via USB to USB cable or USB to RS 232 cable option 2 Turnon the printer power switch 3 Open Diagnostic tool and set interface The default setting is USB USB to USB cable USB to RS 232 cable Interface Interface hd The default interface setting is USB PMA interface If USB interface IS ETHERNET connected with printer no other settings need to be changed in the interface field Select Wireless tab and click on Built in wireless module item Enter the new WLAN settings in the editor Press Set button to set the new settings to the printer The Wi Fi LED will turn on blue the
34. ose soll nahe dem Ger t angebracht und leicht zug nglich sein 5 Das Gerat ist vor Feuchtigkeit zu schutzen 6 Bei der Aufstellung des Gerates ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Beschadigungen hervorrufen 7 Beachten Sie beim AnschluB ans Stromnetz die AnschluBwerte 8 Dieses Gerat kann bis zu einer AuBentemperatur von maximal 40 C betrieben werden Battery safety warning DO NOT throw the battery in fire DO NOT short circuit the contacts DO NOT disassemble the battery DO NOT throw the battery in municipal waste The symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste siis CAUTION Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions ORSICHT Explosionsgetahr bel unsachgemen Austausch der Batterie Ersatz nur durch denselben oder einem om Hersteller empfohlenem nlichen Tyo Entsorgung gebrauchter Batterien nach Angaben des Herstellers Class B FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance w
35. perly Print speed is not set properly Print head element is damaged Poor Print Quality Missing printing on the left or right side of label The print head is dirt ee ine Gray line on the blank label p beds Clean the platen roller The platen roller is dirty Please refer to section 8 Wrong label size setup Set the correct label size The printer is in Hex Dump Turn off and on the printer to skip the Irregular printing mode dump mode 55 8 Maintenance This session presents the clean tools and methods to maintain your printer 1 Please use one of following material to clean the printer Mm Cotton swab M Lint free cloth m Vacuum Blower brush m 100 Ethanol or Isopropyl Alcohol 2 The cleaning process is described as following 1 Always turn off the printer before cleaning the print head 2 Allow the print head to cool for a minimum of one minute 3 Use a cotton swab and 100 Ethanol or Isopropyl Alcohol to clean the print head surface Clean the print head when changing a new label roll Print Head Print Head Print Head Element ES N ES ge Element Head Cleaner Pen 1 Turn the power off Platen Roller 2 Rotate the platen roller and wipe it Clean the platen roller when l changing a new label roll thoroughly with water to wipe It Sensor Compressed air or vacuum Month C Exterior Wipe it with water dampened cioth interior Brush or vacuum e Do not touc
36. rton One printer unit One Li ion rechargeable battery 5800 mAh One Windows labeling software Windows driver CD disk One quick installation guide One auto switching AC adaptor One belt clip lf any parts are missing please contact the Customer Service Department of your purchased reseller or distributor 2 2 Printer Overview 2 2 1 Front View 11 1 Power on off button 2 Feed button 3 Printer status LED indicator 4 Battery status LED indicator 5 Media cover release button 6 Peel off sensor Without for linerless model 7 Print head 8 Transmissive sensor Gap sensor 9 Media holder lock switch 10 Media holder 11 Media cover 12 Reflective sensor Black mark sensor 13 Platen roller 14 Tear Peeler bar Without for linerless model 15 Peeler module Note The media sensor position is selectable by factory adjustment Please refer to this figure for default settings Default center position For LCD control panel option please refer to subsection 2 3 2 for more details 2 2 2 Rear View Li ion battery Belt chip Battery open clasp Hanger for shoulder strap External label entrance chute USB interface MicroSD card socket se eee Se PS Power jack Note Recommended MicroSD card specification MicroSD 1 GB MicroSD 4 GB The DOS FAT file system is supported for the SD card Folders files stored in the SD card should be in the 8 3 filename format
37. t est soumis aux deux conditions suivantes 1 cet appareil ne doit pas causer d interf rence et 2 cet appareil doit accepter toute interf rence notamment les interf rences qui peuvent affecter son fonctionnement Informations concernant l exposition aux fr quences radio RF La puissance de sortie mise par l appareil de sans fil est inf rieure a la limite d exposition aux fr quences radio d Industry Canada IC Utilisez l appareil de sans fil de facon a minimiser les contacts humains lors du fonctionnement normal Ce p riph rique a t valu et d montr conforme aux limites SAR Specific Absorption Rate Taux d absorption sp cifique d IC lorsqu il est install dans des produits h tes particuliers qui fonctionnent dans des conditions d exposition des appareils portables For WiFi _ iv Ce p riph rique a galement t valu et d montr conforme aux limites d exposition aux RF d lC dans des conditions d exposition a des appareils portables les antennes sont moins de 20 cm du corps d une personne For Bluetooth EME DCE WHIT KH O DETER RUHR o O A AT ARE FETE AL EN A IRIE Lb EE o O FT RATER RN FLT AN ABC Bl UA HE RR JER O FA IEA ERA IAA re EEE vate He REF d BA ARTE H Se HE Contents LOU COR een tale to Lace on aa la uote 1 Product AMIE OUU CLIOM ic 1 1 9 Product Features susanne 2 1 2 1 Printer Standard Features cian 2 1122 Printer Optional Features ans 3 1 3 G
38. ton to enter the Print Setup item Select the TSPL2 item Enter the Speed setting mode 3 At this status you can scroll up or scroll down to select the value of print speed Then press the LX button to save the selected value into the printer Press butter to back to Ready mode 39 6 2 Main Menu Overview There are 5 categories for the main menu You can easy to set the settings of printer without connecting the computer Please refer to following sections for more details File Manager v v v DRAM Print Config English Initialization v v FLASH Dump Mode v Sera y Wireless Print Head Bluetooth Date Time Display Note The Wireless LAN function is optional for Alpha 4L series 20 6 3 Setup This Setup category can set up the sensor serial comm wireless Bluetooth date time and display settings 6 3 1 Printer Setup 6 3 1 1 Printer setup for TSPL2 Speed Density Direction Print Mode Offset Main Menu Setup TSPL2 Shift X Shift Y Reference X Reference Y Code Page Country Hem Description S Use this item to setup print soeed The each increase or decrease is 0 5 ips Available setting is from 1 to 6 Use this option to setup printing darkness The available setting is Density from 0 to 15 and the step is 1 You may need to adjust your density based on selected media Speed a The direction sett
39. utton to setup 4 The detail functions in the Printer Function Group are listed as below Printer Function Function Description Cs _ Cabidesersor Calibrate Sensor Setup group media sensor fied aa Ethernet Setup Setup the IP address subnet mask gateway for Ethernet Setup the on board Ethernet __Acseup RTC Setup Synchronize printer Real Time Clock with PC abet Factory Default Hemi eli and restore the settings to Reset Printer Reset Printer Reboot printer Print Test Page Print Test Page Print a test page Configuration Page Configuration Page Print printer configuration Dump Text Dump Text To activate the printer dump mode Ignore AUTO BAS Ignore AUTO BAS Ignore the downloaded AUTO BAS program Exit Line Mode Exit Line Mode Exit line mode __ Pesswod Setup Password Setup Set the password to protect the settings For more information about Diagnostic Tool please refer to the diagnostic utility quick start guide in the CD disk Utilities directory 35 5 3 Setting Bluetooth by Diagnostic Tool 1 Connect the printer and computer with a cable Note The printer connects with the computer via USB to USB cable or USB to RS 232 cable option 2 Turnon the printer power switch 3 Open Diagnostic tool and set interface The default setting is USB USB to USB cable USB to RS 232 cable Interface Interface use vi The default interface setting is USB interface If USB interface is c
40. will be changed as following figures Beep sound twice gt 5 blinks gt 5 blinks gt 5 blinks gt Turn on the printer 4 1 3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings to defaults Printer initialization is activated by the following procedures 1 Turn off the printer power switch 2 Hold on the FEED button E then turn on the power switch 3 Release the power switch when l LED color turn on amber Note In this moment you should still hold on the FEED button 4 The printer will beep sound twice later then release the FEED button El when the indicator becomes and blinking 5 Printer will restore printer settings to defaults Note Please refer to section 4 5 for printer defaults The LEDs will be changed as following figures Beep sound twice gt 5 blinks gt 5 blinks gt 5 blinks gt Turn on the printer 27 4 2 Power on Utility for LCD Panel Option Please follow the steps below for different power on utilities 1 Turn off the printer power switch 2 Hold on the FEED button E then turn on the power switch 3 Release the power switch when Error LED color turn on red Note In this moment you should still hold on the FEED button 4 The printer will beep sound twice later then release the button el when LCD indicate for different functions Power on utilities for LCD panel The LCD will be changed
41. xposure compliance SAR Value 0 663 W kg 111 RF exposure warning For Bluetooth The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment The equipment must not be co located or operating in conjunction with any other antenna or transmitter Canada Industry Canada IC Notices This Class B digital apparatus complies with Canadian ICES 003 and RSS 210 Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Radio Frequency RF Exposure Information The radiated output power of the Wireless Device is below the Industry Canada IC radio frequency exposure limits The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized This device has been evaluated for and shown compliant with the IC Specific Absorption Rate SAR limits when installed in specific host products operated in portable exposure conditions For WiFi This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions antennas are less than 20 cm of a person s body For Bluetooth Canada avis d Industry Canada IC Cet appareil num rique de classe B est conforme aux normes canadiennes ICES 003 et RSS 210 Son fonctionnemen
Download Pdf Manuals
Related Search