Home

ASE-1209

1. User s Manual www tmatlantic com To use the Soldering Tweezers connect it to ASE 1107 soldering station PART1 Precaution In this instruction manual warning and caution are defined as follows A WARNING WARNING Misuse may potentially cause death of or serious injury to the user CUATION Misuse may potentially cause injury to the user or physical damage to the objects involved For your own safety be sure to comply with these precautions CAUTION e When the power is on the tip is between 200 C 392 F and 400 C 752 F Since mishandling may lead to bums or fire be sure to comply with the following precautions e Do not touch the metallic parts near the tip e Do not use the product near flammable items e Advise other people in the work area that the unit can reach a very high temperature and should be considered potentially dangerous e Turn off the power while taking breaks and when finished using the unit e Before replacing parts or storing the unit turn off the power and allow the unit to cool the room temperature e To prevent damage to the unit and ensure a safe working environment be sure to comply with the following precautions e Do not use the unit for applications other than those specially described in the instruction manual e Before using the HOT TWEEZER IRON for the first time calibrate the tip temperature e Donotrap the HOT TWEEZER IRON against the working bench to sh
2. WARNING Use 191 192 or other soldering testers to calibrate the Tip temperature Apply solder or flux e f there is insufficient solder on the PCB or the soldered area is too small apply solder or flax to the PCB Solder may also be applied to the tip Melt the solder e Place the tip on the soldered part and melt the solder confirm that the solder is fully melt e Remove the component After confirming that the solder is fully melted lightly squeeze the TWEEZER to grasp the component and lift to remove the component CAUTION The high temperature of the tip may damage the PCB and put off the circuit diagram Set the temperature at 300 C and the tip temperature can be improved slowly with the work condition When operating use the temperature as low as possible to prevent the sensitive component from damage and stop the tip character from decreasing PART 4 Replacing the tip CAUTION Be sure to turn off the power switch before replacing the tip Loose the nipple by turning it counterclockwise It is not necessary to pull it out completely 1 Insert the new tip as far as it will go and adjust it so that it is parallel to the other tip 2 Tighten nipple to fix the tip in place 3 The tip temperature may vary according to the shape of the tip you d better calibrate it with soldering tester Number Model_ Partname Dimension Shape Ab 2023 B2300 Heat Resistance 25mm Pad A AKTAKOM SMD Hot TWEEZER Iron ASE 1209
3. ake off residual soldering or otherwise subject the iron to severe shocks 2 e Do not modify the unit e Use only genuine QUICK replacement parts e Do not wet the unit or use the unit when your hands are wet e The operating process will produce smoke Make sure the area is well ventilated e Pull on the plug to disconnect the HOT TWEEZER IRON from the station outlet Do not pull the cord e While using the unit don t do anything which may cause bodily or physical damage PART 2 Summarization Specifications Power 24V AC Power Consumption 25W 2 Heating Element Ceramic Heater Tip to grounded resistance under 20 Tip to grounded Potential under 2mV Max temperature 400 C Applicable Models The unit is applied for those iron stations 969 967 702 937 936 926 etc which are suitable for ceramic heating stations NOTE stations are not included Connections Between pins 4 1 5 3 5 O Normal amp 5 Heating Between pins 1 amp 43 58 Q Normal 2 Sensor Between pin 3 amp Tip Under 20 PART3 Operating Instruction Set the temperature Never set the temperature to any value over 400 C 752 F Doing so may damage the station Set the temperature according to the type of the work to be done

ASE-1209

Contents

Download Pdf Manuals

Related Search

Related Contents