S4 User Manual 0107.book - Premier Lighting and Production
Contents
1. 115X 375 115 8 000 3 050 K 1000 hours HPL 750 120 750 120 21 900 3 250 K 300 hours HPL 750 120x 750 130 16 400 3 050 K 1500 hours HPL 575 120 575 120 16 520 3 250 K 300 hours HPL575 120x 575 120 12 360 3 050 K 2000 hours HPL 750 230 750 230 19 750 3 200 K 300 hours HPL 750 230x 750 230 15 600 3 050 K 1500 hours HPL 575 230 575 230 14 900 3 200 K 400 hours HPL575 230X 575 230 11 780 3 050 K 1500 hours HPL 375 230X 375 230 7 250 3 000 K 1000 hours HPL 750 240 750 240 19 750 3 200 K 300 hours HPL 750 240x 750 240 15 600 3 050 K 1500 hours HPL 575 240 575 240 14 900 3 050 K 400 hours HPL575 240x 575 240 11 780 3 050 K 1500 hours HPL 375 240x 375 240 7 250 3 000 K 1000 hours To be used with ETC Dimmer Doubler Color frame holder Retaining clip in the locked position Figure 2 The color frame holder is equipped with a spring loaded retaining clip that prevents color frames and accessories from falling out See Figure 2 WARNING Make sure all color frame accessories are locked in position with the retaining clip before hanging the Source Four fixture Step 1 Release the retaining clip by pushing it sideways while gently pulling backwards Source Four User Manual Step 2 Step 3 Insert the color frame Lock the retaining clip by pushing sideways while gently pushing forward The performance of saturated colors may be less than desirable in any t2. View Road P O Box 620979 Middleton Wisconsin 53562 0979 USA m Tel 608 831 4116 Fax 608 836 1736 London UK Unit 26 28 Victoria Industrial Estate Victoria Road London W3 6UU UK m Tel 44 0 20 8896 1000 m Fax 44 0 20 8896 2000 Rome IT a Via Ennio Quirino Visconti 11 00193 Rome Italy Tel 39 06 32 111 683 m Fax 39 06 32 656 990 Holzkirchen DE Ohmstrasse 3 83607 Holzkirchen Germany m Tel 49 80 24 47 00 0 Fax 49 80 24 47 00 3 00 Hong Kong Rm 1801 18 F Tower 1 Phase 1 Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong m Tel 852 2799 1220 Fax 852 2799 9325 Service Americas service etcconnect com m UK service etceurope com m DE techserv hoki etcconnect com w Asia service etcasia com Web www etcconnect com w Copyright 2008 ETC All Rights Reserved m Product information and specifications subject to change 7060M1200 06 01 m Rev C m Released 2010 01
3. the yoke with the provided yoke bolt and lock washer Step 2 Place the C clamp on mounting pipe then tighten the pipe bolt to secure it Step 3 Loosen the C clamp pan screw and rotate the yoke to the desired position Step 4 Tighten the pan screw to lock the fixture CAUTION Tighten C clamp pipe bolt to 15 20 ft Ibs approximately finger tight plus up to one quarter turn Do not exceed 25 ft Ibs Do not use excessive force Tighten the yoke pivot bolt to 5 10 ft lbs approximately finger tight plus up to one eighth turn Do not exceed 15 ft lbs Do not use excessive force Adjusting the yoke position The Source Four provides multi positioning capabilities within its yoke for overall fixture height and angle Setting the fixture height within the yoke The Source Four has a two position yoke for modifying the overall height in which the fixture is mounted see Figure 11 To change the height position perform the following steps General use position YA O 5 d Low clearance position Figure 11 Step 1 Remove the yoke locking knobs washers and hex bolts from either side of the fixture Step 2 Raise or lower the fixture to the desired position within the yoke Step 3 Reinstall the yoke s hex bolts washers and locking knobs Step 4 Tighten the yoke knobs to secure in position Setting the angle within the yoke Yoke locking knob Figure 12 Step 1 Loosen the yoke locking knobs see Fi
4. DUCE FOUT User Manual Production Dates September 2004 Present Copyright 2008 Electronic Theatre Controls Inc All Rights reserved Product information and specifications subject to change Part Number 7060M1200 06 01 Rev C Released 2010 01 Picking 7060M1001 C Table of Contents Basic Assembly va aa ae MR TERR Rd 1 Fixture information eisena teki een eee 2 Replacing the HPLLamp 0020 eee ee nenn 4 Adjustmerits seen st atra adorada m ies 5 Centering lamp and adjusting the field 5 Focusing the beam ranama eee 5 Shaping the beam saeu riore eee n 6 Rotating the barrel assembly 000 essen 7 Adjusting the C clamp oooccccccc eee 7 Adjusting the yoke position 0 0 00 8 Cleaning Lens and Reflector llli iles 9 Cleaning 14 19 26 36 50 70 90 and all EDLT glass lens GS iu E N cn cle nego Sh ee dd 9 Cleaning 5 and 10 polymer lenses 222220 9 Cleaning the reflector 0 llli lees 10 ETC Emphasis Expression Insight Imagine Focus Express Unison Obsession Il ETCNet2 EDMX Source Four Revolution Sensor and WYSILink are either registered trademarks or trademarks of Electronic Theatre Controls Inc in the United States and other countries All other trademarks both marked and not marked are the property of their respective owners Basic Assembl
5. L lamp Lamp retention brackets i Lamp retaining clips St Lamp housing li ue Knurled bolt Figure 3 A lamp must be installed before you use the fixture Note Verify that the HPL lamp you intend to install is suitable for your facility s voltage 115 120 230 and 240 volt HPL lamps are available See HPL lamp table page 2 Operating HPL lamps above their rated voltage reduces lamp life and can cause premature lamp failure WARNING Let the lamp cool before replacing Step 1 Disconnect power to the Source Four before installing the lamp Step 2 Loosen the knurled bolt on the back of the lamp housing and pull the housing out Step 3 Holding by the base remove the HPL lamp from its box CAUTION Use caution when installing or replacing any lamp When installing replacing lamp be sure to point the lamp away from your face and away from others before inserting it firmly into the assembly This may prevent injuries if the lamp should break INCORRECT X A CORRECT Note To avoid premature lamp failure do not touch the lamp glass If you do clean it carefully with isopropyl alcohol and a clean lint free cloth Allow to dry before operation Step 4 Align the flat sides of the lamp base with the retention brackets on either side of the socket as shown in Figure 3 Step 5 Push down on the lamp base until the lamp seats firmly When properly installed t
6. e barrel as shown in Figure 6 Step 2 Slide the lens tube forward or backward to achieve the desired beam edge Step 3 Once the fixture is focused tighten the beam focus knob Shaping the beam The beam can be shaped using the shutters see Figure 1 a pattern an optional drop in iris or by rotating the barrel Pattern Projection The pattern holder slot is on the top side of the barrel and in front of the shutters It accommodates A size B size and glass pattern holders see Figure 7 A Size Pattern holder holds 3 diameter patterns B Size Pattern holder holds 2 5 and 2 75 diameter patterns 3 12 Diameter 2 75 Diameter gt Figure 7 Note Because the Source Four aperture is 3 inches wide ETC recommends using A size patterns for maximum pattern effectiveness Note Enhanced Definition Lens Tubes EDLT provide for a crisper pattern projection Drop in iris slot Use an optional donut in the accessory holder to enhance pattern projection Donut diameter range should be 2 5 to 2 75 Drop In Iris Slot Figure 8 The drop in iris slot is located on the top of the barrel and in front of the pattern holder slot It accommodates either a drop in iris or a motorized pattern device When the slot is not in use a small sheet metal cover secured with two Phillips screws prevents light leakage see Figure 8 Step 1 Use a Phillips screwdriver to loosen the sc
7. e beam focus knob and retainer bolt Cleaning 5 and 10 polymer lenses To quickly clean the lenses remove dust with a blast of oil free air If this is not sufficient follow these steps CAUTION Handle polymer lenses by their edges only Never rub anything dry on a polymer lens Step 1 Remove the beam focus knob at the bottom of the barrel see Figure 1 Remove the lens tube from the barrel Step 2 Use a Phillips screwdriver to remove the brackets that hold the lens in place Remove the lens from the tube Step 3 Dip the lens in a clean isopropyl alcohol water mixture 9 parts water to 1 part isopropyl alcohol Step 4 Use a soft moistened nylon bristle brush to wash the lens smooth side in a linear non circular motion Step 5 Use the same brush to lightly wash the lens ridged side by following its ridges Step 6 Dip the lens in a clean isopropyl alcohol water mixture 9 parts water to 1 part isopropyl alcohol Step 7 Dry the smooth and ridged surfaces with an air gun Make sure the air flow moves liquid away from you Step 8 Inspect the lens for dirt Repeat steps 3 7 if necessary Step 9 Setthe lens back in the lens tube with the ridged side facing the front of the tube Reinstall the lens brackets Step 10 Slide the lens tube back into the barrel with gel frame retainer on top Reinstall beam focus knob Cleaning the reflector WARNING Unplug the fixture before attempting to clean th
8. e reflector To quickly clean the reflector remove the lens tube and clean the dust from the reflector with a blast of oil free air You may also wipe the reflector with a clean lint free cloth If either method is not sufficient follow these steps Step 1 To protect the lamp housing during cleaning remove the lamp housing by loosening the knurled bolt and pulling the housing straight out See Figure 3 Step 2 Remove the barrel rotation knob located at the bottom of the barrel see Figure 1 Use a Phillips screwdriver to remove the retainer bolt located on top of the reflector housing Step 3 Rotate the barrel 45 in either direction Carefully remove the barrel from the reflector housing Step 4 Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 50 50 mixture of each can be used to clean the glass surface Step 5 Insert the barrel into the reflector housing with the iris pattern slot on top Align the triangles on both parts Step 6 While gently pressing in rotate the barrel 45 clockwise until it sets into position then rotate the barrel counterclockwise 45 The barrel should be firmly attached and the triangles should be aligned Step 7 Reinstall the barrel rotation knob and tighten the retainer bolt Step 8 Reinstall the lamp housing and tighten the knurled bolt Source Four User Manual 11 ODE Corporate Headquarters 3031 Pleasant
9. gure 12 Do not remove them Step 2 Tilt the fixture to the desired position Step 3 Tighten the yoke locking knobs to secure in position Source Four User Manual Cleaning Lens and Reflector WARNING Do not use ammonia based or other harsh commercial cleaners Clean lens and reflector only as directed Commercially available glass cleaning agents should be avoided as they may contain ammonia other harsh chemical detergents or abrasive agents These cleaners may damage the glass surface and the Anti Reflective coatings Do not immerse or soak the glass in any cleaning solution Replace lenses if they contain visible damage cracks or deep scratches that may impair their effectiveness Cleaning 14 19 26 36 50 70 90 and all EDLT glass lenses Step 1 Remove the beam focus knob and retainer bolt from the barrel see Figure 1 Remove the lens tube from the barrel Note To clean the inside of lenses it is necessary to remove the lenses from the lens tube for cleaning Instruction for removing the lens can be found in the Source Four Assembly Guide available for download at our website www etcconnect com Step 2 Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 50 50 mixture of each can be used to clean the glass surface Step 3 Slide the lens tube back into the barrel with the color frame retaining clip on top Reinstall th
10. he top of the lamp s base will be even with he top edges of the retention brackets CAUTION Improperly installed lamps cause premature lamp failure and socket problems Step 6 Press lamp retaining clip across lamp base to secure Step 7 Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt Source Four User Manual Adjustments Centering lamp and adjusting the field Flat field best adjustment Rear lamp Inner Knob housing peak flat field adjustment Hot spot lamp pulled out too far Field with hole lamp Outer Knob lamp pushed in too far center adjustment Figure 4 Figure 5 The two concentric knobs located on the lamp housing allow you to align the lamp and adjust its field See Figure 4 The outer knob centers the lamp within the reflector The inner knob adjusts the lamp s field Step 1 Turn on the Source Four and aim it at a flat surface Adjust the barrel to create a hard edge Step 2 Unlock and loosen the outer knob by turning it counterclockwise Step 3 Gently move the outer knob from side to side and up and down until the lamp is centered within the reflector Step 4 Once the lamp is centered turn the outer knob clockwise to lock it in place Step 5 Finally turn the inner knob either clockwise or counterclockwise to achieve an optimum flat field See Figure 5 Focusing the beam Beam focus knob Figure 6 Step 1 Loosen the beam focus knob located under th
11. heatrical lighting fixture especially when equipped with a 750w lamp For best results always use high quality color media rated for high temperature use ETC s optional Conical Gel Extender part 7060A 1048 will provide maximum color media life For 14 lens tubes use part PSF1029 Gel Extenders are not recommended for 70 and 90 lens tubes due to the extremely wide angle beam Note A variety of heat shield products is also available from many color media manufacturers Follow the manufacturer s instructions for the use of these products For maximum gel life with specific lens tubes refer to the tables below Lens Tube Soft Focus Back Sharp Focus Soft Focus Forward Soft Focus Forward Lamp flat Lamp cosine Lamp peak Lamp cosine 14 worse good best good 70 best good worse good 90 best good good worse 19 worse better better not applicable 26 worse better better not applicable 36 better better worse not applicable 50 worse better better not applicable ED Lens Tube Soft Focus Back Sharp Focus Soft Focus Forward Soft Focus Forward Lamp flat Lamp cosine Lamp peak Lamp cosine 19 worse better better not applicable 26 better better worse not applicable 36 better better worse not applicable 50 better better worse not applicable Replacing the HPL Lamp HP
12. rews on the drop in iris slot cover Do not remove screws Step 2 Slide the cover completely forward to expose the slot Step 3 Insert the iris or motorized pattern device For an iris install the flat side toward the shutters and make sure the iris handle extends from the slot Source Four User Manual Step 4 Slide the slot cover back toward the shutters until it meets the iris handle Leave enough space to move the iris handle Step 5 Secure the drop in iris slot cover by tightening the screws Rotating the barrel assembly Barrel rotation knob a Y Xu Nu Figure 9 Step 1 Loosen the barrel rotation knob directly behind the shutters on the underside of the reflector housing see Figure 9 Do not remove the barrel rotation knob Step 2 Rotate the barrel to the desired position up to 25 in either direction from the centered position Step 3 Once the barrel is positioned tighten the barrel s rotation knob to lock it in place Adjusting the C clamp C clamp Pan screw Yoke bolt and lockwasher wt Figure 10 The C clamp attaches the fixture to the mounting pipe and allows you to adjust the position of the fixture once it is mounted see Figure 10 Step 1 Tightly fasten the C clamp to
13. y Yoke hee handle e Retainer bolt 3 gt Shutters Pattern holder slot Color frame Drop in iris slot V Barrel assembly 2 Lens tube Lamp housing assembly LE gt Yoke locking knob ee d Reflector housing panel rotation knob NOTE Safety cable is included for d cUL applications brem focus knob Color frame holder Figure 1 WARNING Please note the following safety warnings before use Do not mount the fixture on or near combustible surfaces Do not operate the fixture without a lens installed Always hang the fixture with the color frame retaining clip in the locked position A Fixture information HPL lamp table CAUTION Do not use lamps other than the HPL in Source Four fixtures Use of lamps other than HPL will void UL CUL safety compliance and your warranty Lamp code Watts Volts Initial Lumen Color temp Average rated life HPL 780 77 750 77 22 950 3 250 300 hours HPL 550 77 550 77 16 170 3 250 300 hours HPL 550 77X 550 77 12 160 3 050 2000 hours HPL 750 115 750 115 21 900 3 250 K 300 hours HPL 750 115X 750 115 16 400 3 050 1500 hours HPL 575 115 575 115 16 520 3 250 K 300 hours HPL 575 115X 575 115 12 360 3 050 K 2000 hours HPL 375 115 375 115 10 540 3 250 K 300 hours HPL 375
Download Pdf Manuals
Related Search