BB - 202 Black Digital User manual EN web
Contents
1. 10 11 If you have more than 1 Camera Unit to pair you can repeat the above step with the next Camera Unit s until all of them are correctly paired If you would like to skip pairing of particular Camera ID press P button of Monitor Unit once Basbau Camera Pairing System Waiting signal from CAM1 OK Waiting signal from CAM2 SKIP Press PAIRING of Camera Unit to pair Press P to skip and pair the next CAM ID Press power button to abort and turn off Maximum 4 Camera Units can be paired to the Monitor Unit The screen will show the correspondent Camera ID number while pairing Press and hold power button for 2 seconds at any time you have finished the pairing process You will then shut down the Monitor Unit and new setting will be saved Turn on the Monitor Unit again will activate the new setting 5 Trouble Shooting If you don t get a screen Including Basbau Logo at all 1 2 Make sure both the Camera unit and Monitor unit are turned on The green Power LED will light up and indicated the system is on If the Power LED green is not light up please check if the A C adapter is correctly installed and the wall electrical socket is on For trouble shooting purpose please connect the Monitor Unit to the A C adapter besides of using the internal Lithium battery If the Power LED green is light up but there is no screen Pls remove the battery and unplug the A C adapter Wait for 102. WARNING Modifications not authorized by the manufacturer may void users authority to operate this device This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions MI O D L 1 This device may not cause harmful interference and m 2 This device must accept any interference received including interference that may cause BB 202 Black
3. Digital undesired operation a 1 Specification Features Digital 2 4GHz wireless transmission for both video and audio signal 2 Part List Encrypted data transfer to ensure 100 privacy l J Monitor Unit Adopting Frequency Hopping FHSS technology to switch between different channels automatically b Camera Unit Extended transmission distance up to 300m at open area 3 Installation 3 Supports up to 4 camera units simultaneously Automatic night vision function when operating in dim area a Monitor Unit Installation Remote sound activation VOX from camera unit b Camera Unit Installation Portable monitor unit with Lithium battery and built in battery charger 4 Operation i Monitor unit a Power On Off 4 b Volume Adjustment 5 Display 2 4 TFT color display at 320x240 resolution c Brightness Adjustment 5 Audio 1W d VOX Voice Activation Function 5 Frequency 2400 2483 MHz auto select by Frequency Hopping FHSS e Night Vision Function 5 Pairing Supports 4 camera units simultaneously f Battery Charging 5 ee g LED Indicators 6 Pairing Switches h Mou nting 6 Volume 10 steps control i Pairing Adding Camera Unit 8 Bognes S a RERA Cou 5 Troubleshooting 9 Power green Low Battery flash LEDs Signal Coverage blue poor reception flash Battery Charging red Activation Both manual or voice triggered VOX from camera unit OSD Brightness Volume Pairing selection Battery Lith
4. Please read carefully this user manual before using the BB 202 Black Digital wireless monitoring system Failure to follow these warnings and the assembly instructions could result in serious inquiry or death PORTABLE COLOR Keep the AC adapter cords out of the reach of children LCD DIGITAL WIRELESS Phen adapter cords Make sure that they are not walked on or pinched by furniture or Use ONLY the AC adapters provided in this kit Using other 3 parties AC adapters may cause fatal damage to the monitoring system MONITO Rie SYSTEM Make sure the provided AC adapters are at the same electrical voltage of your country Do not place the monitoring system or its cord within the child reach Provide proper ventilation for the monitoring system when it is operating Do not cover the Monitor unit and Camera unit with any material such as a blanket Do not place the Monitor and Camera units in a poor ventilation area such as a drawer N ST R U CT O N M A N U A L Do not immerse the monitoring system in water Clean it only with a dry cloth Do not use the monitoring system near any possible wet areas such as a bathtub shower basin sink laundry tub Donotuse the monitoring system outdoors Keep the monitoring system away from heat sources such as fireplaces radiators stove Do not attempt to open the Monitor unit Camera unit and the AC adapters No user serviceable parts inside Risk of electrical shock fire or death
5. bb202blackdigital pdf 11
6. dest C Brightness Adjustment By pressing the of button at the right side of the Monitor Unit will adjust the brightness of the display Press to increase the brightness Press to reduce the brightness The screen shows 0 for dimmest and 5 for brightest D VOX Voice Activation VOX is a build in function of BB 202 Black Digital system When the system entered the standby mode the screen of Monitoring Unit will turn off for energy saving purpose At the same time VOX will be activated automatically and detects the sound level nearby the Camera Unit Once it reaches the certain level VOX will awake the Monitoring system from standby mode E Night Vision The Camera Unit have build in 8 pieces of Infra red LEDs for picking up clear images in dim area but not affecting the environmental brightness When the photo light sensor detects low ambient light level the night vision function will turn on automatically F Battery Charging The Monitor Unit is equipped a rechargeable Lithium battery for portable use When the Power LED green is flashing it indicates the Lithium battery is at low battery level You are required to charge your Lithium battery by the provided AC adapter Attach the AC adapter to the monitor unit and plug the AC adapter into the wall AC socket pic 7 The charging process will start automatically and the Charge LED red will light up When the Charge LED goes off it indicat
7. es the battery is full and you can unplug the A C adapter from the Monitor Unit Wall Outlet Adaptador Pic 7 G LED Indicators Camera Unit Monitor Unit NOTE To achieve the best performance of signal transmission please place the antenna at a vertical position e Green light Power On Power e Flashing green light Low battery Wall Mount e Off Power Off Place 2 screws on the wall at 5 5cm pitch Hook the camera unit on the screws as e Blue light Good Signal Coverage shown in pic 10 Lift the cover plate to adjust the flipping angle 0 90 degree or Signal e Flashing blue light Marginal Signal Coverage swinging angle 15 degree e Off No Signal e Red light Lithium Battery Charging charge e Off Battery Not Charging Camera Unit e Green light Power On saat eats Sarco ee e Off Power Off YD c lt H Mounting Pic 10 Monitor Unit p Flat Bed J Place the Camera Unit on a solid horizontal plane Lift the cover plate to adjust the Push belt clip lock and move up m 5 flipping angle 0 90 degree or swinging angle 15 degree the belt clip to the direction as shown 6 4 N in pic 8 F Stand Push belt clip lock and move down the belt clip to the direction as shown in pic 9 Lift the belt clip and lock into position Pic 11 I Pairing Adding Camera Unit NOTE The Monitor Unit and Camera Unit were already paired in manufacturing process In general user
8. ium battery A C power 6V 1A DC adaptor Mounting mechanism Camera unit Multi purpose stand belt clip or wall mounted CMOS Sensor 1 6 VGA 640x480 Lens F No 1 8 EFL 2 95mm BFL 2 488mm Night vision 8x IR LED LED Power Flipping angle 0 90 degree Swinging angle 15 degree Microphone built in A C power 6V 1A DC adaptor Mounting mechanism Transmitting Power Flatbed or wall mounted 16dB 2 Part List A Monitor Unit Strape Holder Antenna Belt Clip Stand Volume Up Brightness Chargue LED Up Signal LED Volume Down Brightness Down Power LED A C Adaptador Jack Power Pairing Battery Cover B Camera Unit Antenna Lens A C Adaptador Jack 3 Installation A Monitor Unit Installation 1 As shown in pic 1 lift the Belt Clip at the back of Monitor Unit and remove the battery door 2 Insert the Lithium battery in correct direction Make sure the metal contact of battery is in touch with the metal contact of battery bay 3 Close the battery door 4 Charge the battery by using the provided AC adapter Attach the AC adapter to the Monitor Unit as shown in pic 2 Then plug the AC adapter into the wall AC socket 5 The battery charging process will start automatically Charge LED on For first time usage please keep charging the battery for at least 3 hours until the charge LED goes off 6 Press power to power on the Monitor Unit Wall Outlet y A C gt a Adaptad
9. mance 4 Press the P button and scan through 4 pre set camera ID to make sure your Camera Unit was not paired to other pre set ID Video problem 1 Try to adjust the brightness level by pressing the brightness button until it gives a desirable image 2 If the colour goes off it indicates that the Camera Unit is working in a dim area and the night vision Infra red function is on Sound problem as Try to adjust the volume level by pressing the volume button until it gives a desirable sound level 2 If you have heard the shrill sound feedback you placed the Monitor Unit and Camera Unit too close Place them apart or lower the volume level will solve the problem Do not attempt to open the casing of the system or the battery Improper use of the system will cause fatal damage Moreover the warranty will be void 10 1313 bash Basbau Innovation declares that the BB 202 Black Digital is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC This declaration of conformity may be consulted at www basbau com declarationofconformity 1999 5 EC 8437012400016 bb202blackdigital padf Por la presente Basbau Innovation declara que BB 202 Black Digital cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva 1999 5 CE Pueden consultar la declaraci n de conformidad en www basbau com declarationofconformity 1999 5 EC 8437012400016
10. minutes Plug the A C adapter back to the Monitor Unit and retry to power on the Monitor Unit If you have seen the opening screen but nothing afterwards 1 Please check if your Camera unit is turned on The green Power LED will light up and indicated the system is on 2 Make sure the Camera unit and Monitor Unit are within range of each other For trouble shooting purpose you should remove all the obstacles between two units and keep shortest distance within 5 meters 3 Press the P button and scan through 4 pre set camera ID to make sure your Camera Unit was not paired to other pre set ID 4 Pls remove the battery and unplug the A C adapter Wait for 10 minutes Plug the A C adapter back to the Monitor Unit and retry to power on the Monitor Unit 5 If all above steps fail you are advised to pair the Monitor Unit and Camera Unit Pls following the steps mentioned in Pairing Adding Camera Unit If the screen displays the below picture 1 The Monitor Unit may be out of the signal coverage from the Camera Unit Remove the obstruction or get closer to the Camera Unit until the blue LED is on will re gain the signal automatically basbau WARNING 2 Try to place both antennas vertically It Out of gives better effectiveness of signal signal coverage transmission 3 Other 2 4GHz or high frequency devices like WIFI microwave oven may interfere the monitoring system Turn off these devices will give better perfor
11. or 1 Attached the provided AC adapter to the Camera Unit as shown in pic 3 The power jack is located at the bottom of the Camera Unit Plug the AC adapter into the wall AC socket 2 Press Power Button to power on the Camera Unit B Camera Unit Installation Wall Outlet A C Adaptador 4 Operation A Power On Off 1 To power on the Monitor Unit press the Power button once The Power LED will show green colour indicating the Monitor Unit is on 2 To power on the Camera Unit press the Power button once The green LED will light up indicating the Camera Unit is on hasbi 3 For power saving purpose the Monitor Unit will automatically enter Standby mode after inactivity of 180 seconds 3 mins and the screen will show as pic 5 besb i VOX activated Entering stand by mode pic 4 shows the opening screen with Basbau Logo pic 5 4 To resume from stand by mode press any button except power button will awake the system At the time the system awake you will see the screen as shown in pic 6 bead System Activating pic 6 5 To power off the Monitor Unit press and hold the Power button for 2 sec 4 B Volume Adjustment By pressing the of VOL button at the left side of the Monitor Unit will adjust the sound volume of the speaker Press to increase the volume Press to reduce the volume The screen shows 0 for mute mode and 9 for lou
12. s are not advised to perform any pairing by their own If user have brought another set of BB 202 Black Digital wireless monitoring system or BB 202 Black Digital Camera unit you can pair the new Camera Unit by the following procedures As a result the Monitor Unit will support multiple Camera Units simultaneously 1 Power Off all Monitor Unit and Camera Units 2 Press and Hold the P button of the Monitor Unit 3 Press the Power button of the Monitor Unit 4 Release both the P and Power button 5 You will then enter the pairing mode screen as shown below Basbau Camera Pairing System Waiting signal from CAM1 Press PAIRING of Camera Unit to pair Press P to skip and pair the next CAM ID Press power button to abort and turn off 6 Press POWER button of your Camera Unit to power on your Camera Unit s 7 If you have only 1 Camera Unit to pair press the Pairing button on your Camera Unit If pairing is success the screen of your Monitor Unit will show below message Basbau Camera Pairing System Waiting signal from CAM1 OK Waiting signal from CAN2 Press PAIRING of Camera Unit to pair Press P to skip and pair the next CAM ID Press power button to abort and turn off 8 If you have only 1 Camera Unit to pair you can now turn off the Monitor Unit by press and hold Power button for 2 seconds New setting will be saved Turn on the Monitor Unit again will activate the new setting 9
Download Pdf Manuals
Related Search