User`s Manual for FT-90x Series
Contents
1. 5 Choose file My Recent Documents A Desktop My Computer My Network File name Places Files of type jal Files Cancel E Figure 4 25 Windows file selection menu popup Select on the firmware then click Upgrade the Software Upload Progress would show the file upload status The firmware upgrade may take 60 seconds Firmware Upgrading may take 60 seconds A Firmware Upgrade process must NOT be interrupted Figure 4 26 Firmware Upgrade progress screen Once the firmware is loaded to the system successfully The following screen appears The system will load the new software after reboot 33 System Rebooting Please wait for a while for Web interface re login Figure 4 27 Software successfully loaded notice screen BS Note Do not power off the converter until the update progress is complete Do not quit the Firmware Upgrade page without press the Upgrade button after the image is BS Note loaded Or the system won t apply the new firmware Users have to repeat the firmware upgrade processes again m Logout Press this function the web interface will go back to login screen The screens in Figure 4 28 and Figure 4 29 appear Microsoft Internet Explorer E 2 Are you sure to Logout l Cancel Web Smart Media Converter PLANET Web Smart 10 100Base TX to 100Base FX Media Converter Username Password Copyright 2007 PLANET Technology Corpo2. 16 4 3 Port Configuration This function allows displaying each port s status The Link Status in the screen displays the current connection speed and duplex mode else this function will show down when the port is disconnected Press the Refresh button to renew the screen The screen in Figure 4 5 appears Port Configuration Flow Py Link lode Control Ingress Rate Limit Egress Shaping MOE Auto Speed Ww oy Disabled s No Limit NoLimit v toor Disabled v ae vi Ee Figure 4 5 Port Configuration screen The page includes the following configurable data e Port e Link e Mode e Flow Control e Ingress Rate Limit Indicate the Copper port and Fiber port Displays the current connection speed and duplex mode of Copper or Fiber Allow configuring the port speed and operation mode Draw the menu bar to select the mode e Auto Speed Setup Auto negotiation e 10 half Force sets 10Mbps Half Duplex mode e 10 Full Force sets 10Mbps Full Duplex mode e 100 half Force sets 100Mbps Half Duplex mode e 100 full Force sets 100Mbps Full Duplex mode e Disable Shutdown the port manually Default value Auto Speed Allow Enable or Disable flow control for selected port e Enable 802 3x flow control is enabled on Full Duplex mode or Backpressure is enabled on Half Duplex mode e Disable No flow control or backpressure function on no matter Full Duplex or Half Duplex mode D
3. A 3 Fiber Optical Cable Connection Parameter The wiring details are as below m Fiber Optical patch Cables Standard Fiber Type Cable Specification 100Base FX Multi mode 50 125um or 62 5 125um 1300nm 100Base FX Multi mode 50 125um or 62 5 125um 1310nm Single mode OO 25pm 100Base BX U Single mode 9 125um TX 1310 RX 1550 100Base BX D TX 1550 RX 1310 A 4 Power Information The power jack of FT 90X is with 2 5mm in the central post and required 5VDC power input It will conform to the bundled AC DC adapter and Planet s Media Chassis Should you have the problem to make the power connection please contact your local sales representative Please keep the AC DC adapter as spare parts when your FT 90X is installed to a Media Chassis 2 5mm lt DC Receptacle 2 5mm 5V for each slot OC DC receptacle is 2 5mm wide that conforms to and matches the Media Converter 2 5mm DC jack s central post Do not install any improper unit model of the Media Converter A 4 Available Modules The following list the available Modules for FT 905A MFB FX SFP Port 100Base FX Transceiver 1310nm 2KM MFB F20 SFP Port 100Base FX Transceiver 1310nm 20KM MFB FA20 SFP Port 100Base BX Transceiver WDM TX 1310nm 20KM MFB FB20 SFP Port 100Base BX Transceiver WDM TX 1550nm 20KM 2080 AA3450 000 C 27
4. 100Base F X e Complies with IEEE 802 3 IEEE 802 3u 10 100Base TX 100Base FX standard e Auto Negotiation for 100Base TX Half Duplex or 100Base Full Duplex e Compact size e Co work with PLANET MC family Media Chassis MC 700 1000R 1500 e Built in IP Base Web interface for remote management e Layer 2 Smart Feature M IEEE 802 3x Full Duplex Flow Control Back Pressure in Half Duplex eliminate packets loss M Supports Maximum frame size to 2Kbytes M Supports auto MDI MDI X function on RJ 45 Port M Store and forward mechanism M Supports two priority queue level M Supports QoS Scheme Port based 802 1p 4 M Supports Bandwidth Control Kbps for both Ingress and Egress M Supports Broadcast Storm Control to optimize network bandwidth M Supports Ethernet Statistics on both TP and Fiber interface M Look Back Test Function LBT Link Loss Return LLR M Firmware upgrade via HTTP protocol e 5VDC power supply e LED indicators for easy network diagnose e Reset Button at the front panel for reset to factory default e Choice of fiber connector from ST SC MT RJ VF 45 and WDM multi mode single mode fiber 100Base SFP 1 4 PRODUCT SPECIFICATION FT 902S FT 902S FT 902S FT 906A FT 906B Model FT 902 FT 905A 20 20 15 35 50 Hardware Specification 1 x 10 100Base TX port 1 x 100Base FX port SC SFP WDM O davon TX 1310 TX 1550 RX 1550 RX 1310 xl 7 s o ae os ea gt gt gt 10Base T 2 pair UTP C
5. Loss Return function of the device The fiber ports of the Web Smart Media Converter have been designed with an LLR function for troubleshooting a remote connection Refer to LLR description at next page for more detail The default value is Enable mg Broadcast Storm Control To prevent the broadcast storm the converter implements a broadcast storm control mechanism When this function is enabled a port begins to drop incoming broadcast packets if the received broadcast packet counts reach the threshold defined in the field The screen in Figure 4 9 appears Converter Configuration METEO E Both O TP CIF MA 6 Disable O Enable Broadcast Storm Control i i Disable Glass of Services WRR Priority High Low LLR Mode Disable Enable Apply Notice When using two converters don t enable the both device s LLR function at the same time Figure 4 9 Broadcast Storm Control Configuration screen m Class of Services and WRR priority The converter implements two levels of priority queues high priority and low priority The priority for each packet is based on 802 1Q VLAN tag scheme Each incoming packet is mapped to either a high priority queue or a low priority queue When no CoS function is enabled the first in first out forwarding method is used The output schedule mode and weight function for the ratio of high low priorities is defined in the Class of Service field a When multipl
6. nee ea sere 36 A DEVICE SRJA5 PINASSIGNMENTS trar aaa 36 AZ RAS CABLE PINASSIGNMENT marrera a a AA AA AS AA AA A IT 36 A 3 FIBER OPTICAL CABLE CONNECTION PARAMETER sisi A A AA 37 AA POWER INFORMATION ca deeend oie anes rate uta elses mata ae cm lade ate eaeana ae ageteacnlea dese uamieeacene 37 PAE AN ACA BLE MODULES ip A AA AAA E 37 1 INTRODUCTION 1 1 Package Contents Check the contents of your package for following parts e Web Smart Media Converter x1 e CD ROM user s manual x1 Quick installation guide x1 o External 5VDC 2A power adapter x 1 If any of these are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 2S Note FT 905A is with one vacant SFP module slot The 100Base FX SFP module is not bundled with in the package 1 2 How to Use This Manual This Web Smart Media Converter User Manual is structured as follows Section 2 Installation It explains the functions of FT 90x and how to physically install the FT 90x Section 3 Web Management The chapter explains how to manage the converter by Web interface Section 4 Configuration It contains information about the Smart function of FT 90x Appendices It contains cable information of FT 90x 1 3 Product Features e One channel media conversion between 10 100Base TX and
7. 5e TP Cable Network gt PLANET 100Base F X orkiny amp Communication 10 100Base TX to 1000Base FX Fiber Network TX 2 2 1 Stand alone Installation To install a FT 90X stand alone on a desktop or shelf simply complete the following steps Step 1 Turn off the power of the device station in a network to which the FT 90X will be attached Step 2 Ensure that there is no activity in the network Step 3 Attach fiber cable from the FT 90X to the fiber network TX RX must be paired at both ends Step 4 Connect the 5VDC power adapter to the FT 90X and verify that the Power LED lights up Step 5 Turn on the power of the device station the PWR LEDs should light when all cables are attached 5V DC power 100Base FX 10 100Base TX SC Fiber UTP 7 XN Note Please refers to APPENDIX A for detailed wiring information of the FT 90X To prevent from optic acceptor malfunction check the both wires transmitter before power on the converter E FT 905A Installation FT 905A is with high reliability and flexibility to extend the distance up to 2Km 20Km or longer It depends on the 100Base FX SFP transceiver modules The SFP transceivers are hot plug e and hot swappable You can plug in and out the transceiver to from any SFP port without having to power down the converter To install FT905A with 100Base FX SFP simply complete the following steps Step 1 Precede with the steps 4 and steps 5 of session 2 2 1 Stand a
8. FT 902 FT 902515 539 59U FT 905A FT 906A20 906B20 1 PLANET Networking amp Communicalton Trademarks Copyright PLANET Technology Corp 2007 Contents subject to which revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to comp
9. Figure 4 19 Configuration backup successes screen Restore The converter will restore to previous backup saved configuration while the Restore button be pressed And please note that once the Restore button be pressed Web interface will disconnected for a while Reload the WEB browser to re login the system 30 ie Restore button the Web Interface will disconnected for 1 to previous backup configuration oe Figure 4 20 Configuration restore screen m Factory Reset The Factory Reset button can reset the FT 90x back to the factory default mode Be aware that the entire configuration will be reset and the IP address of the FT 90x will be set to 192 168 0 100 ek al aran the E vail Bock is a default made The fault IP address is 192 168 0 100 Figure 4 21 Factory Reset screen Once the Factory Reset item is pressed the screen in Figure 4 22 appears System Rebooting Please wait for a while for Web interface re login Ta He l de TTU LE Figure 4 22 Factory Reset screen To reset the IP address to the default IP Address 192 168 0 100 Press the hardware reset button ZS Note at the front panel about 10 seconds After the device be rebooted You can login the management WEB interface within the same subnet of 192 168 0 xx FX TX LNK E ey pu NOONE O O RESET Web Smart Ethernet DON 10 100Base TX 10 100Base TX to 00Base FX Hardware Reset button 31 4 7 4
10. Firmware Upgrade The Firmware Upgrade page contains fields for downloading system image files from the Local File browser to the device The screen in Figure 4 23 appears gt PLANET ee System Port Configuration Pri he Upgrade bulto C eat onfiguration E E A Statistics Tomis Figure 4 23 Firmware Upgrade screen To open Firmware Upgrade screen perform the folling 1 Click Tools gt Firmware Upgrade 2 The Firmware Upgrade screen is displayed as in Figure 4 24 Firmware Upgrade Press the Upgrade button please wait a while to access Firmware Upgrade mode for update firmware After firmware upgrade process complete and the systerr will redat automatically for new firmware Upgrade Figure 4 23 Firmware Upgrade screen 3 Click the Upgrade button of the main page the Firmware Upgrade Mode displayed 39 Firmware Upgrade Mode Firmware Upgrade This mode allows to proceed the firmware Upgrade on converter Please select the location of the firmware file on your PE by Using the browse button as below then press the Upgrade button Note Ensure that the File of type field in the browse window is set to All filesi 2 To cancel the Firmware Upgrade process power cycle the switch without selecting any files Figure 4 24 Firmware Upgrade screen Click the Browse button of the main page the system would pop up the file selection menu to choose firmware 4
11. M m dad Ceeyerter Status IP Address PC Work Station 192 168 0 100 with IE or Netscape Browser 11 3 2 2 Login the media converter Before you start configure the FT 90X please note the FT 90X is configured through an Ethernet connection make sure the manager PC must be set on same the IP subnet address For example the default IP address of the FT 90X is 192 168 0 100 then the manager PC should be set at 192 168 0 x where x is a number between 2 and 254 and the default subnet mask is 255 255 255 0 Use Internet Explorer 6 0 or above Web browser Enter IP address http 192 168 0 100 the factory default IP address to access the Web interface When the following login screen appears please enter the default username and password default user name and password is admin Press Login to enter the main screen of FT 90X The login screen in Figure 3 1 appears 3 PLANET Web Smart Media Converter PLANET Web Smart 10 100Base TX to 100Base FX Media Converter Username Password 1 Copyright 2007 PLANET Technology Corporation All rights reserved Figure 3 1 Login screen 1 For security reason please change and memorize the new password after this first setup XA Note 2 Only accept command in lowercase letter under web interface 12 4 CONFIGURATION The FT 90X Web Smart Media Converter provide Web interface for Switch smart function configuration and make the Sw
12. NTENTS ndo a e di lo o ode o do d 1 k2 OV TO USE THS MANUA cc vacaciones o tea odie once 1 ko FPRODUCTEEATURE Stilo coloidal 1 de ed BS es Sal ok i Gy 2 TON o ee Se Pe nD nn Peer ONT a ee eee ee 2 2 INSTALLATION sei e o beatae Gute 3 Za PRODUCT DESCRIPTION a O AO tana co 3 LANE LEIOA NOME Pan Cle soi A A descend Rea neues 4 2241674 D plo e AAA A e 5 2 bo A A O 6 2 2 INSTALE THEG ONVERTER roaraa A aa ht a he rt eg alan ce ees ee T 2 21 tand aloneinStallanOns a sth a a a NN E 7 2 2 2 Chassis Installation and Rack Mounting iii A A AS 9 3 gt WEBMANAGEMEN TS andinas 11 O A O A A eens Meee 11 3 A MANAGEMENT METODOS ion 11 A A deetenctusent laren 11 3 2 2 LOGIN Ine media CONVE ssl oi el 12 4 CONFIGURATION ot e e o ce Len o LEAL 13 ANIMAN MENU AAA cca urte va teaucionuraea es 13 AZ SY SUE A A it ise 14 Si io A A enee 14 42 2 NP Eto pl Le 8 es Lilo sister PO N a acute ETE tac aides ecdced ised E E nel Ee E 15 AZ PASS WORE SEWN ii A en Olin ee aa un dad A ata ad eta 16 AS PORT CONEA CURA TON a o o e a o See A O O 17 AA GONVERTER CONFIGURATION a a o o od di 20 AO G ONVERTER STATUS de a o dl o th aah etek ct a ae eae 24 A Loa ete a ute Ae tte as 25 A AN OOUS aana r A A a Badia claps ae chon Aia 2 ABT LODO AGI TOS ii A a 27 RS A sachets aad ob ade acck wea chee ea noe e a 29 AT GONIQuratiOn S CUINA cause heed A AAA AS AA 29 A E AAA A A A A A A aAA 32 Ds TROUBLESHOO TIN ed Naa dl dll O US e 35 APPENDIX A ia a o e e o Dl A
13. Web Management page with default user name and password 2 Please contact Planet support team and the mail address is support_switch planet com tw 235 A 1 Device s RJ 45 Pin Assignments m 10 100Mbps 10 100Base TX Contact MDI Pt te ae 2 2 TX 3 3 RX 6 RX Implicit implementation of the crossover function within a twisted pair cable or at a wiring panel while not expressly forbidden is beyond the scope of this standard A 2 RJ 45 cable pin assignment el Ss There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection APPENDIX A Straight Cable SIDE 1 SIDE 2 1273456 B5SDE 1 1 White Orange 1 White Orange 2 Orange 2 Orange 3 White Green 3 White Green 4 Blue 4 Blue amp White Blue 5 White Blue 12345678 SIDE 2 6 Green 6 Green T White Brown T White Brown 8 Brown 8 Brown Cross Over Cable SIDE 1 SIDE 2 123466 7 6 SIDE 1 1 White Orange 1 White Green 2 Orange 2 Green 3 White Green 3 White Orange i d Blue d Blue ri 5 White Blue 5 White Blue 1234567 8 SIDE 2 6 Green 6 Orange Y White Brown T White Brown 8 Brown Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network 36
14. at 3 4 5 up to 100 m 100Base TX 2 pair UTP Cat 5 up to 100 m 50 125um or 62 5 125um multi mode fiber cable up to 2km 9 125um single mode cable provide long distance for 15 20 35 50km or longer very on SFP module 10 20Mbps for Half Full duplex 100 200Mbps for Half Full duplex 200Mbps for Full Duplex 26 x 70 x 97mm H x W x D 5V DC 2A Standard Conformance IEEE 802 3 10Base T IEEE 802 3u 100Base TX 100Base FX IEEE 802 3x Flow Control IEEE 802 1p Class of Service 0 50 C 25 70 C 10 to 90 relative humidity non condensing 10 to 90 relative humidity non condensing FCC Part 15 Class B CE Store Ret I I 2 INSTALLATION This section describes the functionalities of FT 90X s components and guides how to install it on the desktop or shelf Basic knowledge of networking is assumed Please read this chapter completely before continuing 2 1 Product Description The Web Smart FT 90x Media Converters supports conversion between 10 100Base TX and 100Base FX network There are SC SFP connectors and single mode multi mode media for your needs Ethernet signal that allows two type segments connect easily efficiently and inexpensively This converter can be used as a stand alone unit or as a slide in module to the PLANET Media Converter Chassis MC 700 MC 1000 and MC 1500 Each Web Smart converter is able to manage through the Web Interface The p
15. e CoS schemes are enabled the data packet is treated as the high priority as long as any one of three CoS schemes is mapped to high Take the following example for detail explanation If a port is set as a low priority port when it receives a packet which embeds with high priority VLAN tag this packet will be forwarded as a high priority packet In the other words the priority of a packet would be set to high if any of two CoS schemes is interpreted as the high priority Converter Configuration MESE Both TP OFX MA aa 6 Disable Enable Broadcast Storm Disable v Control L E A Fist In First Out w First In Fist Cut Stict Priority Weighted Round Eobin LLR Mode O Disable Enable WRR Priority High Low Apply Notice When using two converters don t enable the both device s LLR function at the same time Figure 4 10 Class of Services Configuration screen m LLR Mode Link Loss Return LLR The fiber ports of the Web Smart Media Converter have been designed with an LLR function for troubleshooting a remote connection LLR works in conjunction with LLCF When LLR is enabled the port s transmitter shuts down when its receiver fails to detect a valid receive link LLR should only be enabled on one end of the link and is typically enabled on either the unmanaged or remote device The diagram below shows a typical network configuration with a good link status using Smart Media C
16. e sure that you backup the current configuration of FT 90X else the entire configuration will be erased when pressing the RESET button e Press and release the RESET button shortly the device will be rebooted e Press the RESET button more than 10 seconds the device will back to the factory default mode the entire configuration will be erased 5 2 1 3 FT 90X Rear Panel The rear panel of the converter indicates one DC jack which accepts input power with 5V DC 2A m FT 90x series Figure 2 6 Rear Panel of FT 90x Power Notice 1 The device is a power required device it means it will not work till it is powered If your networks should active all the time please consider using UPS Uninterrupted Power Supply for your device It will prevent you from network data loss or network downtime 2 In some area installing a surge suppression device may also help to protect your media converter from being damaged by unregulated surge or current to the converter or the power adapter 6 2 2 Install the Converter This section describes how to install your FT 90X Web Smart Media Converter and make connections to the converter Please read the following topics and perform the procedures in the order being presented The hardware installation of PLANET FT 90X Web Smart Media Converter do not need software configuration To install your FT 90X on a desktop or shelf simply complete the following steps 10 100Base T X Cat 5
17. e total number of received packets that were longer than 1518 octets This number excludes frame bits but includes FCS octets that had either a bad Frame Check Sequence FCS with an integral number of octets FCS Error or a bad FCS with a non integral octet Alignment Error number The field range to detect jabbers is between 20 ms and 150 ms Displays the number of collisions received on the interface since the device was last refreshed Number of xx byte frames received on the interface since the device was last refreshed Clear Counters button this option will reset all of the statistic counts Refresh Now button which use this option to refresh the statistics 26 4 7 Tools This section provides tools of FT 90x As listed at the left of the main screen the configurable smart functions are shown as below m Loop Back Test m System Reboot m Configuration Setting eu Firmware Upgrade 4 7 1 Loop Back Test Use this function to tell the converter to send fiber signals request to the other convert at end side You can use this to check whether the converter can communicate with partner converter Once you click the Apply button the converter will send n signals and the results will be displayed below the configurable data And make sure the partner converter also supports the Loop Back reply function The Loop Back Test screen in Figure 4 13 appears Te Loop Back Test Send Packet HE Number 0255 pp
18. efault value Disable The value of inbound traffic limitation in kilobit per second kbps The possible values are e No Limit e 512K e 1M e 2M e 4M e 8M e 10M e 50M 17 Default value No Limit The Ingress Rate Limit configuration field as show in Figure 4 6 e Egress Shaping The value of outbound traffic limitation in kilobit per second kbps The possible values are e No Limit e 512K e 1M e 2M e 4M e 8M e 10M e 50M Default value No Limit The Egress Shaping configuration field as show in Figure 4 7 2 Note When set each port to run at 100M Full 100M Half 10M Full and 10M Half speed modes The Auto MDIX function will disable Port Configuration Port Link Tos Fiai Ingress Rate Limit Control E Aos y Datel v No Limit v NoLimit v He irait 4 a x ET Figure 4 6 Port Configuration Ingress Rate Limit screen 18 Port Configuration Port Link Mode UE Ingress Rate Limit Control Auto Speed Disabled 100F Disabled 7 No Limit v Figure 4 7 Port Configuration Egress Shaping screen 19 4 4 Converter Configuration This page allows setup Management Port Loop Back Reply Broadcast Storm Control Class of Services and LLR Mode Press the Apply button to take affect The screen in Figure 4 8 appears Converter Configuration Msn einem Both OTP OFX Mi a 6 Disable Enable Broadcast Storm e Control Class of Services First In First Ou
19. guration Converter Configuration i Converter Status i Statistics Tools Figure 4 3 IP Configuration screen The page includes the following configurable data IP Address The IP address of the interface The factory default value is 192 168 0 100 Subnet Mask The IP subnet mask for the interface The factory default value is 255 255 255 0 Gateway The default gateway for the IP interface The factory default value is 192 168 0 1 After change the default password if you forget the password Please press and release the 23 Note Reset button in the front panel of FT 90X the current setting will be lost and the FT 90X will restore to the default mode 15 4 2 3 Password Setting This function provides administrator to secure Web login The screen in Figure 4 4 appears Password Setting Login Name Old Password New Password Confirm Figure 4 4 Password Setting screen The page includes the following configurable data Login Name Displays the user name Old Password Enter the old password is required before entering the new password New Password Specifies the new password The password is not displayed As it entered an corresponding to each character is displayed in the field The maximum length is 16 characters Confirm This confirms the new password The password entered into this field must be exactly the same as the password entered in the Password field
20. itch operate more effectively They can be configured through the Web Browser A network administrator can manage and monitor the FT 90x from the local LAN This section indicates how to configure the media converter to enable its smart function 4 1 Main Menu After a successful login the main screen appears the main screen displays the converter Welcome page The screen in Figure 4 1 appears 3 PLANET Ka Web Smart Media Converter Sy Lerm I Part Configuration _ NE Sonverter Configuration arar Status Web Smart Past Ethernet Media Converter Welcome to PLANET Statistics PLANE Technology Corporation lools Logout 11 No 96 Min CRhuan Road Hsin Tien Taipei Taiwan R O C Tel BA6 2 2219 9518 Fax G66 2 2219 3528 Email Sglesmplarvet com bey C pia O 2007 PLANLI Technology Corp r tior All right reserved Figure 4 1 Web Main screen As listed at the left of the main screen the configurable smart functions are shown as below System Check the hardware software version and System MAC address and IP address of the converter Port Configuration Setup per port Speed Duplex mode Flow Control and In Out bandwidth control Converter Configuration Setup the broadcast storm control QoS and converter LLR mode Converter Status Shows the converter s copper and Fiber ports linking status Statistics Shows the statistics of packet count from copper and Fiber ports 9 To
21. lone Installation to connect the network cabling and supply power to your converter Step 2 Slot in the 100Base FX SFP Make sure both side of the SFP transfer are with the same media type for example 100Base FX 2Kmto 100Base FX 2Km 100Bas FX 20Km to 100Base FX 20Km 5V DC power 100Base FX SFP transceiver A E 10 100Base TX UTP 100Base FX LC Fiber It recommends using PLANET MFB FX series 100Base FX SFP on the converter If you insert a XA Note SFP transceiver that is not supported the converter will not recognize it Step 3 Connect the fiber cable Attach the duplex LC connector on the network cable into the SFP transceiver 8 2 2 2 Chassis Installation and Rack Mounting To install the media converter in a 10 inch or 19 inch with standard rack follow the instructions described below Step 1 Place your FT 90X on a hard flat surface with the front panel positioned towards your front side Step 2 Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis Figure 2 1 Insert a media converter into an available slot Step 3 Attach a rack mount bracket to each side of the Chassis with supplied screws attached to the package Step 4 After the brackets are attached to the chassis use suitable screws to securely attach the brackets to the rack as shown in Figure 2 2 Step 5 Precede with the steps 4 and steps 5 of session 2 2 1 Stand alone Installation to connect the ne
22. ly Refresh Loop Back Test Result Result Fail Result Counter O Figure 4 13 Loop Back Test screen The Loop Back Test Parameters includes the following fields e Send Packet Enter the number of loop back test packet to send Number 0 255 default 16 e Result PC reports the loop back test result after sending all test frames The possible values are PASS and Fail e Result Counter Shows number of good looped back packet received Note These counters will be cleared when a new auto loop back test procedure is issued After field the parameter and press Apply to execute the Loop Back Test function The result shows at the next table As the Figure 4 14 screen appears Loop Back Test Result Result Fall Result Counter O Figure 4 14 Ping Result screen ES Note Be sure the partner converter had enabled the Loop Back Reply Otherwise the result screen will as like fiber above 28 Converter Configuration Miami SD Both TP OFS MA O Disable Broadcast Storm Disable v Control WRRE Priority High Low LLE Mode O Disable Enable Notice When using two converters don t enable the both device s LLR function at the same time Figure 4 15 Loop Back Reply Enable screen 4 7 2 System Reboot The Reboot page enables the device to be rebooted from a remote location Once the Reboot button is pressed users have to re login the WEB interface about 20 seconds later Microsoft I
23. ly with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at whose own expense CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET Fast Ethernet Web Smart Media Converter User s Manual FOR MODELS FT 902 FT 902S15 FT 902S35 FT 902S50 FT 905A FT 906A20 FT 906B20 REVISION 1 0 FEBRARY 2007 Part No 2080 AA3450 000 2 TABLE OF CONTENTS INTRODUCTION cu do eel ee eel ee alee ete etalk 1 IA RACE CO
24. nternet Explorer E h P Do voy want to restart the switch Cancel Figure 4 16 Reboot dialogue box screen 4 7 3 Configuration Setting This function allows backup and restore the current configuration of FX 90x or reset the converter to factory default The description of the three items as follow and screen in Figure 4 17 appears m Backup To backup save the current configuration to the storage block on this converter m Restore To restore the previous backup configuration from the storage block m Factory To reset the FT 90x back to the factory default mode 29 Y PLANET Web Smart Media Converter Piori Eondigural beer AAA AAA Backup button Convenor Condiqueralioan ratios Save t Convertor Bl als Blatistios Restore bit tee ll T fre I L SCE UD i Tools Press the Factory button the Web ir MAL atl i LAA 100 192 Figure 4 17 Tools Configuration Setting screen Backup All current configurations except IP Configuration will save to converter as backup once the Backup button is pressed Press the Backup button all current configuration except IP Configuration will save to converter as backup Backup Figure 4 18 ToolsiConfiguration Setting Backup screen After the Backup button is pressed and success backup current configuration the screen in Figure 4 19 appears Note Configuration Backup Successed
25. number of octets received on the interface since the device was last refreshed This number includes bad packets and FCS octets but excludes framing bits e Drop Events Which displays the number of dropped events that have occurred on the interface since the device was last refreshed e Pkts Displays the number of packets received on the interface including bad packets Multicast and broadcast packets since the device was last refreshed e Broadcast Pkts Which displays the number of good broadcast packets received on the interface since the device was last refreshed This number does not include Multicast packets e Multicast Pkts Displays the number of good Multicast packets received on the interface since the 25 Received e CRC Align Errors e Undersize Pkts e Oversize Pkts e Fragments e Jabbers e Collisions e Frames of xx Bytes device was last refreshed which displays the number of CRC and Align errors that have occurred on the interface since the device was last refreshed Displays the number of undersized packets less than 64 octets received on the interface since the device was last refreshed Displays the number of oversized packets over 1518 octets received on the interface since the device was last refreshed Indicates the number of fragments packets with less than 64 octets excluding framing bits but including FCS octets received on the interface since the device was last refreshed Indicates th
26. ols Provide tools to Reboot Factory Reset Firmware Update Configuration Upload the converter 13 4 2 System 4 2 1 System Information The System Information page provides information for the current device System Info page helps a network manager to identify the versions and IP Address etc The screen in Figure 4 2 appears Katwortiog amp Commaricnics 7 ss _ Q PLANET Web Smart Media Conv System Infomation Asten normato EC 00 30 4f 0f 90 2 1 IP Configuration Software Version 1 0b07 0131 IP Address 192 168 0 100 Subnet Mask 255 255 255 0 Password Setting Port Configuration Converter Configuration Converter Status Statistics Figure 4 2 System Information screen The page includes the following fields e MAC Address Specifies the device MAC address e Software Version The current software version running on the device e IP Address The current IP Address of the device The IP Address could be manual assigned e Subnet Mask The current IP Subnet Mask setting on the device e Gateway The default gateway for the IP interface The factory default value is 192 168 0 1 14 4 2 2 IP Configuration The IP Configuration includes the IP Address Subnet Mask and Gateway The screen in Figure 4 3 appears gt PLANET ee Parra Web Emart Philia Cirer ir System IP Configuration IP Address 60100 Subnet FASE aes 754 D Gateway TR BELL Port Confi
27. onverter for remote connectivity Note that LLR is enabled as indicated in the diagram Management Switch Hub Media Media Switch Hub Management Station w SNMP Converter Converter w SNMP Station LLCF is LLCF is _ default default 000 0 0 0 0 0 90 Cable e LED lit established link o LED unlit no link If one of the optical conductors is bad as shown in the diagram box below the converter with LLR enabled will return a no link condition to its link partner With LLCF default the no link condition is carried forward to the switch hub where a trap is generated to the management station and the administrator can then determine the source of the loss 2 Management Switch Hub Media Media Switch Hub Management Station w SNMP Converter Converter w SNMP Station COH Pr oar 0 O O OBoknO OOO Port2 en Port 1 Link Loss Carried OO Link Loss Carried Link Loss e LED lit established link o LED unlit no link When using two converters don t enable the both device s LLR function at the same time ZS Note If it is the link can never be established 23 4 5 Converter Status The page shows the converter s copper and fiber linking status The screen in Figure 4 11 appears Converter Status Detected No Flow control Disable Disable Auto negotiation Enable The page includes the following fields e Ports e Signal detect SD e Link Status e Duplex mode e Flo
28. owerful Web Smart Media Converter supports flow control QoS bandwidth control and Ingress Egress rate control etc The statistics function of the Web Smart converter help the administrator to remote analysis and count the packet flow of the current Ethernet link The Web Smart function also includes the LLR and Loop Back Test LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net It provides more flexible settings for converters LLR Link Loss Return means when a device connected to the converter and the fiber line loss the link the converter s fiber will disconnect the link of transmit The LLR function can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net With 100Base FX SFP ports the FT 905A is with high reliability and flexibility to extend the distance up to 2Km 20Km or longer It depends on the 100Base FX SFP transceiver modules m Supplier and Model name PLANET FT 90X firmware version 1 0 vs ferrite opm e pastora Ai 100Base FX eee ae F N Marar Remote WEB Management 20 Km Converter Satus Management Client 100Base FX Fiber 100Base TX UTP Remote WEB Management 2 1 1 FT 90X Front Panel Figure 2 1 2 2 amp 2 3 shows a front panel of FT 90X FX TX O Ons i A F q Om Lad oog ll e Oy oos ik Web Smart E
29. ration All rights reserved Figure 4 29 Login screen 34 3 FROUBLESHOOTING This chapter contains information to help you solve problems If the media converter is not functioning properly make sure the media converter was set up according to instructions in this manual The Link LED is not lit Solution 1 Check the cable connection and remove duplex mode of the converter 2 Check the port configuration of the link partner make sure the two side devices with the same link configuration Performance is bad Solution Check the full duplex status of the device If the device is set to full duplex and the partner is set to half duplex then the performance will be poor 100Base TX port link LED is lit but the traffic is irregular Solution Check that the attached device is not set to dedicate full duplex Some devices use a physical or software switch to change duplex modes Auto negotiation may not recognize this type of full duplex setting Why the device doesn t connect to the network Solution Check the LNK ACT LED on the device Try another port on the connected device Make sure the cable is installed properly Make sure the cable is the right type Turn off the power After a while turn on power again How to deal forgotten password situation of device Solution 1 If the device is implemented with Reset button press the button at the front panel about 10 seconds After the device be rebooted Login the device
30. t WRR Priority High Low LLR Mode Disable Enable Apply Notice When using two converters don t enable the both device s LLRA function at the same time Figure 4 8 Converter Configuration screen The page includes the following fields e Management Port Allow to filter the Web management packets for this converter by income port The possible field values are e Both Accept management packets from both TP and Fiber ports e TP Accept management packets only from TP port e FX Accept management packets only from Fiber port The default value is Both e Loop Back Reply Allow the converter to reply for Loop Back Test or not For more detail about the Loop Back Test and Loop Back Reply function please refer to chapter 4 7 1 e Broadcast Storm Allow disable or enable broadcast storm control on the converter The possible Control field values are e Disable e Allow 20 e Allow 50 e Allow 80 The default value is Disable e Class of Services Allow to choose different policy for Class of Service on the converter The possible field values are 20 e First In First Out e Strict Priority e Weighted Round Robin e WRR Priority This field is available when choose Weighted Round Robin as Class of Service ve schedule It indicates that traffic output ration of high priority and low priority The High Low possible field values are e 1 1 e 2 1 e 4 1 e 8 1 e LLR Mode To enable or disable the LLR Link
31. thernet 10 100Base TX 10 100Base TX to 00Base FX Figure 2 1 PLANET FT 902 FT 902S Front Panel FX TX OO O Oe O 52 Web Smart Ethernet FWR 100 10 100Base TX 10 100Base TX to 00Base FX Figure 2 2 PLANET FT 905A Front Panel FX TX O OMe O Oca 008 PWR 100 10 00Base TX to IDOBase FX Figure 2 3 PLANET FT 906A B Front Panel A 2 1 2 LED Indicators m System LED m 10 100Base TX Port Function P kits Indicate that the port is link up LNK ACT Indicate that the switch is actively sending or receiving data over that port Off Indicate that the port is link down or no data flow Lit Indicate that the connection made through the corresponding port is running in Full Duplex mode FDX Indicate that the connection made through the corresponding port is running in Half Duplex mode Indicate that the port is operating at 100Mbps Off Indicate that the port is link down or 10Mbps m 100Base FX SC SFP Port Function Lit Indicate that the port is link up LNK ACT ms the switch is actively sending or receiving data over Off Indicate that the port is link down or no data flow t aIL that the connection made through the corresponding port is running in Full Duplex mode Indicate that the connection made through the corresponding port is running in Half Duplex mode N Note To press and release the RESET button The FX 90x will back to the factory default mode B
32. twork cabling and supply power to your switch Caution You must use the screws supplied with the mounting brackets Damage caused to the parts by using incorrect screws would invalidate your warranty 9 FUT oat PEE Te PE tf IEA F aw Polotl toe tt tient toa Figure 2 2 Mounting the Chassis in a Rack 10 3 WEB MANAGEMENT This chapter describes how to manage the FT 90X Topics include Overview Management methods Assigning an IP address to the FT 90X Logging on to the FT 90X 3 1 Overview This chapter gives an overview of switch management The FT 90X provides a simply WEB browser interface Using this interface you can perform various switch configuration and management activities including m System Port Configuration mE Converter Configuration Converter Status Statistics E Tools Please refer to the following Chapter 4 for more details 3 2 Management Methods The way to manage the FT 90X Web Management via a network or dial up connection 3 2 1 Web Management The PLANET Web Smart media converter provides a built in browser interface You can manage the FT 90X remotely by having a remote host with web browser such as Microsoft Internet Explorer Netscape Navigator or Mozilla Firefox Using this management method The FT 90X must have an Internet Protocol IP address accessible for the remote host PLANET Web Smart Media Converter GT m U M AAA
33. w Control e Speed e Auto negotiation Refresh Figure 4 11 Converter Status page screen Indicate the Copper port and Fiber port Shows the current signal detect status of the fiber and TP ports For example if a fiber signal is detected it shows Detected Else shows No The state of the link indicating a valid link partner device Up means a device is successful connected to the port Down means no device is connected The port duplex mode Full transmission occurs in both directions simultaneously or Half transmission occurs in only one direction at a time This mode can be configured only when auto negotiation is disabled and port speed is set to 10Mbps or 100Mbps Shows the flow control status of the port It is active when the port uses Full Duplex Mode Shows the connection speed of the port and the speed can be configured only when auto negotiation is disabled on that port This is the current setting of the port s Auto Negotiation feature 24 4 6 Statistics The Port Statistic page displays the status of packet count from copper port and fiber port The Port statistics screen in Figure 4 12 appears Statistics Multicast Pkts CRC Align Errors Oversize Pkts Fragments 128 250 206 011 O 0 0 O 0 0 a 0 0 0 O 0 0 O Q 0 312 1023 Figure 4 12 Statistics screen The page contains the following fields e Port Indicate the Copper port and Fiber port e Octets Displays the
Download Pdf Manuals
Related Search