DIGITAL PANEL DP02HMNKG USER`S MANUAL
Contents
1. INTERCOM DIGITAL PANEL DPOZ2HMNKG USER S MANUAL amp 1 DEFINITION DPO2HMNKG is a digital outdoor panel with a keypad and a card access pad The Digital panel default setting is for 1 building and up to 255 apartments The panel does not require presetting It is activated and ready to use However it is strongly recommended that you change default settings after installing the panel You can find how to change the settings on the instruction manual After reading the manual you will be fully aware how to use this device 2 Device Instructions 2 1 CALL In standby mode push any button enter the apartment number and then push the CALL button If you do not know the apartment number find the name of the resident via searching the UP DOWN buttons Then press the CALL To call guard press the GUARD button 2 2 DOOR ENTRY A set of four numbers called as PIN Each apartment has its own PIN or apartments have shared PIN to open the building entrance For your safety do not share your PIN with others In standby mode push the C button until the words Enter Your PIN are displayed and enter the four digits door release PIN within 12 seconds Otherwise the system will resume to standby mode Note The default PIN is 1234 The PIN would not appear in the screen for that reason enter the PIN carefully If there is a mistake reset the PIN by pressing the C button and enter the PIN again or enter the rest of2. Menu Settings By using the UP and DOWN buttons you can select sub menus 2 5 1 ENTERING BUILDING NAME ON OPENING SCREEN Opening Screen menu is 1 on Settings Menu As optional building name or Welcoming message is typed Example Welcome to xXx Building To enter the menu enter menu settings first press 1 then press CALL Type your message in Linel then press the CALL to type in Line 2 If you want to leave the Line 2 blank just press the CALL after entering Line 1 Message Each line has 16 digits to use 2 5 2 IDENTIFICATION OF APARTMENT APARTMENT QUANTITY IFQ IFQ menu is 2 on Settings Menu This menu limits the panel on use of the apartment quantity To enter the menu enter menu settings first press 2 then press CALL type total apartment quantity and press CALL to save it NOTE Apartment quantity can be maximum 255 Please pay attention not to leave quantity 0 when you enter IFQ menu 2 5 3 NAME LIST Name List menu is 3 on Settings Menu It is possible to display who the resident at referred apartment number is Visitors can browse the residents via the UP DOWN buttons then press the CALL to call the required apartment To edit the 3 name list menu enter settings menu press 3 then the CALL Type apartment number then press CALL to edit the apartment Type resident name surname then press CALL to save the information 2 5 4 CHANGING DOOR PIN Changing Door Pin menu is 4 on Set
3. the digits to complete the set to four digits then you can enter again 2 3 USE OF THE BUTTONS IN ABC MODE In ABC mode to type the requested letter press relevant button To choose first letter press once To choose second letter press twice To choose third letter press three times EXAMPLES To display C press the 2 three times to display K press the 5 three times quickly This method is called single key mode with many options NOTE When you press another button cursor moves to next digit To move onto right cell on the display or to be able to enter the same letter again wait for few seconds after entering the first letter For more information about the characters you can use table on menu 2 4 2 4 SYMBOLS BUTTON DISPLAYED satirasi ABC2 DEF3 GHI4 JKL5 MNO6 PQRS7 TUV8 WXYZ9 0 SGSOANANINDNBWN NOTE To leave space press 0 for once 2 5 ENTERING MENU SETTINGS In standby mode push any button and see the menu to enter apartment number Enter any apartment number press the C button continuously till the words Settings PIN are displayed then you can enter settings PIN and make the necessary changes The default PIN is 0000 It is strongly recommended to change Settings PIN and store it carefully If you don not press any button within 6 seconds panel switches to standby mode then need to re enter Settings Menu You can press the numbers 1 to 9 to enter sub menus on
4. gs Menu 2 5 9 BUILDING NO SETTINGS ON MULTI BUILDINGS Building No Settings on Multi Buildings menu is 9 on Settings Menu This menu is to set building number Enter settings menu then press 9 then the CALL enter building number then CALL Attention For Multi Building Systems if you don not set building number or leave 0 when an apartment is called system would call the same numbered apartments in all buildings 2 5 11 OPTIONAL BUTTON GUARD BUTTON 4 Optional Button menu is 11 on Settings Menu This menu is to set to call guard s station directly without entering apartment number You can enter any apartment number to call directly default Guard Station number is 255 NOTE Pay attention NOT TO press the CALL without entering apartment number Guard Apartment would be set as 0 2 5 12 DOOR RELEASE TIMER Optional Button menu is 12 on Settings Menu This menu is to set to door releasing time Enter settings menu press 12 then CALL Use the UP DOWN buttons to set the required releasing time then press the CALL to set it D R T range is up to 10 secs 3 CARD ACCESS Applying below instructions you can register the cards that you will distribute to users or you can erase all already registered cards For these operations your system has to be switched ON and Status LED continuously glowing 3 1 Registering user cards a Take one of Administrator cards out of the package and put it close to reader uni
5. ith the same card the card s have to be registered to each and every reader unit connected to desired doors Above registration operations have to be repeated for each door P Technical Specifications Communication Range 28 4 in 70 10 cm 23 oz 645 gr
6. t then make sure that you hear a double warning beep and watch REC LED to blink b Blinking REC LED indicates that the unit is in Registration mode You can then take back the Administrator card c Put user card s close to reader unit rapidly one after the other follow light and sound warnings d When you finish registering user card s you put again the Administrator card near the reader unit and exit Continuously glowing Status LED indicates that you are out of registration mode NOTE In case you wait more then 10 seconds during above operations the system will automatically go out of registration mode 3 2 Erasing all user cards a Take one of Administrator cards out of the package and put it close to reader unit and wait then watch all LEDs to go ON after 20 seconds b Take back the Administrator card c A few seconds later you will see that REC and Confirmation LEDs go ON This means that you are in Erase mode d While REC and Confirmation LEDs are ON erase operation starts as soon as you put the Administrator card close to reader unit During erase operation all LEDs are ON When erase operation is completed Status LED will continuously glow NOTE In erase mode if Administrator card is not placed close to the reader within 10 seconds the system goes automatically out of erase mode In such case erase operation is not realized 3 3 Opening different doors with the same card To open different doors w
7. tings Menu This menu is to change the door opening pin Enter settings menu press 4 then CALL Enter quantity of PIN numbers 1 to 100 then enter PIN numbers for each apartment The default door release PIN is 1234 Quantity of PIN numbers should be entered as defined otherwise default Door PIN would remain 2 5 5 CHANGING SETTINGS PIN Changing Settings Pin menu is 5 on Settings Menu This menu is to change the Settings PIN Enter settings menu press 5 then the CALL and the CALL again Settings PIN appears on the screen to enter four digits New PIN Press the 1CALL to save the new PIN Default Settings PIN is 0000 2 5 6 LANGUAGE OPTIONS Language Options menu is 6 on Settings Menu This menu is to set panel language Enter settings menu press 6 then the CALL Press 1 2 3 4 to select your language then press the CALL to set it Language options below 1 Turkish 2 English 3 French 2 5 7 BACK TO DEFAULT SETTINGS Back to Default Settings menu is 7 on Settings Menu This menu is to reset current settings and it restores manufacturer settings Enter settings menu then press 7 then CALL BACK TO DEFAULT SETTINGS appears on the screen if you press CALL panel would start counting from 1 to 260 then returns to standby mode screen and panel is set to default settings When BACK TO DEFAULT SETTINGS appeared on screen if you press the C the panel would not clear existing information and return to Settin
Download Pdf Manuals
Related Search