ESB 2008 Laydown User Manual - RecDirect Factory Outlets Dr
Contents
1. Attaching Legs to Bench Figure la Step 1 Lay the bench upside down on a soft material i e carpet Figure la Attach the legs using the washers and the allen bolts which are already in the bottom of the tanning bed Use the allen wrench I to tighten Step 2 Turn bench right side up on floor Place so that the power cord connection is facing your wall outlet Attaching Arms to Bench Figure 1b 8 www mercola com Attaching Arms to Bench Figure 1b Attach the left arm A and the right arm B with the two allen bolts E to the bench Figure 1b Use the allen wrench I to tighten Do not over tighten doing so may cause damage Attaching Canopy to Bench Figure 1 Attaching the Canopy to Bench Figure 1 Note To make attaching the canopy to the bench easier you may want to place some of the packing foam from the carton across the bench rails to protect the acrylic and support the weight of the canopy when attaching it Step 1 Two people are required for this step Before lifting the canopy over the bench for placement it is much easier to have the allen bolt ready in hand Step 2 With one person at each end of the canopy unit lift up the canopy above the bench and align the allen bolt holes from the canopy with the arms Slip the allen bolt E through the aligned holes Tighten bolt with the allen wrench To avoid damaging the threaded inserts do not over tighten Do NOT lower ca2. Merc a com Take Control of Your Health USER MANUAL Warranty Tanning systems are warranted to be free from defects in workmanship as follows 5 Years on all metal structural components 1 Year on gas shocks and electrical components 90 Days on acrylics plastics and lamps Dealer s obligation under this warranty is limited to the repair and or replacement of any defective part without charge for that part at the manufacturer s discretion with the following limitations This warranty is extended only to the original purchaser appearing on the sales receipt and is non transferable This product is designed for use by one person at a time Only original parts may be used All major repairs must be completed by an authorized service representative This warranty does not cover transportation charges on the parts Labor costs are not reimbursable for repair or replacement of items Dealer disclaims any responsibility for transportation Dealer further disclaims any responsibility for injury resulting from the failure of equipment or parts due to incorrect installation or operation Dealer shall not be liable for loss or damages caused either directly or indirectly from the use of its products This limited warranty does not extend to any products which have been damaged as result of accident misuse abuse or as a result of service or modification by anyone other than an authorized service representative This w
3. furnished with this equipment Protective eyewear should be worn by all persons in the room when lamps are on Failure to wear protective eyewear during each tanning session may result in severe burns or long term injury to the eyes Only the following lamps may be used in this tanning system Use of any other lamps will void your warranty Solara Classic PN 532000 Solara Classic ReNew PN 532008 Solara Classic Infra Red PN 532007 Solara Classic ReFresh PN 532010 engage in the maintenance of this product This equipment 1 Disconnect power cord before attempting to clean re lamp must be earth grounded DO NOT operate the tanning bed while wet or near water Tanning Bed Specifications Info Dedicated Size Weight Voltage Amps Breaker NEMA pans Timer HxWxL lbs Volts Rated amps Receptacle 28x32x76 170 120 13 15 5 I5R 0 3 Digital This tanning system comes equipped with an internal backup timer Refer to Table of Contents for more information on timers 4 www mercola com Pre Installation Planning Before you begin to assemble your tanning bed please read the following Electrical Requirements A qualified electrician may be needed to assist in fulfilling these requirements VERY IMPORTANT MUST READ EVERY Tanning System REQUIRES a DEDICATED Circuit Breaker This means that your tanning system is the ONLY electrical d
4. http www fda gov http www emedicine com http www intelihealth com http www lupus org http www photosensitivity org Pregnancy You should consult with your doctor before tanning while pregnant 20 www mercola com FOR ADDITIONAL ASSISTANCE PLEASE REVIEW THE HELPFUL SERVICE AND MAINTENANCE HINTS IN THIS USERS MANUAL IF YOU HAVE ADDITIONAL QUESTIONS REQUIRE TECHNICAL SUPPORT INTERESTED IN PURCHASING TANNING ACCESSORIES OR FUTURE UPGRADES FOR NEW LAMPS DO NOT HESITATE TO CONTACT THE AUTHORIZED DEALER WHERE YOU PURCHASED YOUR TANNING BED www mercola com 21 Warranty Information Use of this product in a commercial tanning application automatically results in the voiding of any and all manufacturer s warranties Record and retain this information for ease of service Authorized Dealer Store Address Attach your receipt to this manual 22 www mercola com Tanning Bed General Specifications Required Receptacle sorte dee aed Mais NEMA 5 15R Receptacle Voltage e 8 aah toa 120V 60Hz Minimum ROOM SIZE 644208 Vx8x8 Maximum Ambient Room 80 F Lamp PT ee 1000 Refer to Electrical Requirements See Table of Contents Size Chart Height Tapai Width Length Open Closed H1 99 H2 51 35 32
5. 76 www mercola com 23 Warning Label Information DANGER Ultraviolet radiation Follow instructions Avoid overexposure As with natural sunlight overexposure can cause eye and skin injury and allergic reactions Repeated exposure may cause premature aging of the skin and skin cancer FAILURE TO WEAR PROTECTIVE EYEWEAR MAY RESULT IN SEVERE BURNS OR LONG TERM INJURY TO THE EYES WARNING Read the instruction booklet before using this sunlamp product All persons in the room should wear protective eyewear when lamps are on Recommended eyewear Provided eye shields or equivalent eyewear as defined under 21CFR 1040 20 Other types of eyewear may not provide adequate protection If discomfort develops discontinue use and consult a physician Medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult physician before using sunlamp if you are using medications or have a history of skin problems or think you are especially sensitive to sunlight If you do not tan in the sun you are unlikely to tan from the use of this product Children the elderly or fair skinned people who always burn easily and either never tan or tan minimally should not use this equipment To use lie down on bench and pull canopy down as far as adjustment will allow maintaining at least 2 inches 5 1 centimeters between your body and canopy to avoid eens Manufactured by LPI 1044 Fordtown Rd Kingsport T
6. Acrylic Removal section of this manual Remove a lamp that lights and place it in the spot where the lamp was out If this new lamp doesn t light in this position the ballast may need to be replaced If it does light the first lamp may need to be replaced Two or three lamps located next to each other are not lit Possibly a ballast problem due to a power surge in your household electrical system Contact your Authorized Dealer for replacement assistance Canopy fails to stay in the upright position Double check assembly instructions Gas shocks may have been put on upside down See page 10 Lamp Configuration Mercola 24 Refresh Bed Solara Lamp Classic ReNew ReFresh Infra Red Total Canopy 8 2 2 0 12 10 0 0 2 12 24 Solara Refresh Lamps are centered in the canopy with ReNew lamps on either side Solara Infra Red lamps are centered in the bench Contact your authorized dealer regarding future lamp replacement options www mercola com 17 Frequently Asked Indoor Tanning Questions Is there a safety reset switch No Ifthe bed will not turn on verify the outlet has power If the timer will not respond the bed needs to be serviced Unplug it and call the dealer the bed was purchased from How many times do I have to use the bed before I get a tan That depends on your skin type and how fast you tan It will probably take you approximately 16 ses
7. FDA approved eye shields should be worn while tanning and by everyone in the room while the tanning bed is in operation Your Hair Your hair should be free of any gels mousses sprays or other hair products prior to tanning These products can cause damage to the tanning bed acrylic We suggest you wear either a shower cap or place a towel or pillow under your head Exposure Schedule Determine the correct exposure time according to your skin type Recommended Exposure Times Shown in Minutes Skin Type Week 1 Week 2 Week 3 Week 4 I Sensitive skin burns easily and severely does not tan Not recommended for tanning II Light burns easily and severely tans minimally 4 6 9 12 Normal burns moderately tans average 6 8 10 13 IV Dark burns minimally tans easily and above average 8 10 12 15 MAXIMUM EXPOSURE TIME IS 15 MINUTES ALLOW 48 HOURS BETWEEN ALL TANNING SESSIONS 12 www mercola com Using the Tanning Bed Step 1 Determine your exposure time as outlined in the preceding section Step 2 If using indoor tanning lotion apply before getting into the bed Your Authorized Dealer can assist you with the proper tanning lotion for your skin type Step 3 Put on goggles Step 4 Activate the timer according to the instructions to follow Step 5 Lift canopy Lie down on the bench face up For best results position the canopy as close to you as unit allows When the timer r
8. ING BED SHOULD BE COMPLETELY SHUT DOWN AND UNPLUGGED FROM POWER SOURCE AT LEAST TWO 2 FULL HOURS BEFORE ANY CLEANING OR MAINTENANCE TO ALLOW THE TANNING BED TO ADEQUATELY COOL DOWN www mercola com 13 Preventive Maintenance for Your Tanning Bed Recommended Care After Each Session Weekly Monthly 6 Months Every 1000 hours Clean acrylic surface x Clean pillow x Clean goggles x Inspect clean vents x Clean exterior of bed x Inspect clean reflectors x Inspect clean lamps x Inspect clean underside of acrylics Replace acrylics x Replace lamps X Cleaning and Acrylic Maintenance IT IS NECESSARY TO THOROUGHLY CLEAN AND SANITIZE YOUR ACRYLIC AFTER EVERY USE TO ENSURE CAREFREE OPERATION AND TO MAXIMIZE ITS TANNING EFFICIENCY THE ACRYLIC SHOULD BE CLEANED WITH A NON ABRASIVE DISINFECTANT THAT DOES NOT CONTAIN AMMONIA AND OR ALCOHOL DO NOT USE COMMERCIAL CLEANERS SUCH AS WINDEX OR 409 USE OF AMMONIA AND OR ALCOHOL ON YOUR ACRYLICS WILL VOID THE WARRANTY Take the following steps to maintain your acrylic cleaning the tanning bed use a cotton towel which is much less abrasive than a paper towel Never wipe with a dry cloth as this will generate a slight static which attracts dust Products not approved by Dr Mercola may be harmful and cause premature damage to your acrylic In order to keep the acrylic from being scratched jewelr
9. N 37673 Phone 1 800 208 6369 This product is in conformity with performance standards for sun lamp products under 21 CFR Part 1040 20 and ANSI UL Standard 482 Never tan more than once a day and allow 48 hours between tanning sessions Tanning normally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to maintain desired appearance ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT Solara Classic PN 532000 Solara Classic ReNew PN 532008 Solara Classic Infra Red PN 532007 Solara Classic ReFresh PN 532010 RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 15 MINUTES SKIN TYPE WEEK 1 2 3 4 1 Sensitive Skin Burns easily and severely and does not tan NOT RECOMMENDED FOR TANNING 2 Light Burns easily and severely and tans minimally 4 6 9 12 3 Normal Burns Moderately and tans average 6 8 10 13 4 Dark Burns minimally tans easily and above average 8 10 12 15 Disconnect power cord before attempting to clean re lamp or engage in the maintenance of this product Made in the USA 03 15 13 Copyright 2013 Item 24 www mercola com Rev C
10. WHILE NOT IN USE DO NOT CONVERT THE POWER CORD TO A TWO PRONG CORD OR USE ANY EXTENSION CORD We do not recommend that you connect your tanning system to an extension cord However if you must use an extension to reach your dedicated outlet then it must be a 3 wire extension cord of at least 12 gauge wire for under 12 feet If longer than 12 feet then you will need a 3 wire 10 gauge extension cord good to 25 30 ft AS RECOMMENDED FOR ALL ELECTRICAL APPLIANCES THIS TANNING BED SHOULD NEVER BE OPERATED NEAR WATER OR WHILE YOU ARE WET www mercola com 11 Pre Tanning Guidelines This tanning bed is designed for use by one person at a time not weighing more than 300 lbs Your Skin Before tanning be sure your skin is free of any tanning oils or lotions except those approved for indoor tanning use body lotions or cosmetics Cosmetics or medications applied to your skin may increase your sensitivity to ultraviolet light If you are taking any medication or if you are especially sensitive to sunlight we recommend that you consult a physician before using this or any tanning equipment It is also recommended that you not bathe immediately before using this tanning bed as it removes natural body oils which protect your skin Your Eyes FDA approved eye goggles are provided with this tanning bed and must be worn whenever the tanning bed is operating Regular sunglasses do not adequately protect your eyes from ultraviolet light
11. arranty does not apply to any failure of parts or products due to alterations modifications misuse abuse accidents improper maintenance or failure to follow the specified electrical requirements Such occurrences immediately VOID this warranty THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY No person firm or corporation is authorized to assume for us any other liability in connection with the sale of these goods USE OF THIS PRODUCT IN A COMMERCIAL TANNING FACILITY OR FOR PROFESSIONAL AND MEDICAL SERVICES AUTOMATICALLY RESULTS IN THE VOIDING OF ANY AND ALL MANUFACTURER S WARRANTIES THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR SUN LAMP PRODUCTS UNDER U S FDA SECTION 21 CFR PART 1040 20 www mercola com Congratulations Thank you for choosing our laydown tanning system for your tanning pleasure This tanning system is designed to give you many years of dependable trouble free enjoyment in the comfort of your own home Table of Contents Warranty Safety Information Specifications Info Electrical Requirements Set Up and Assembly Instructions Pre Tanning Guidelines Recommended Exposure Times Using The Tanning Bed Timer Instructions Caring For and Maintaining Your Tanning Bed Preventive Maintenance Matrix Cleaning and Acrylic Maintenance Acrylic Removal and Re insta
12. eaches 0 the lamps will automatically shut off To end the session before your pre set time simply raise the canopy and step out of the tanning bed Step 6 Return the canopy to the upright position before attempting to sit up Timer Instructions This model is equipped with a 15 minute digital timer To start a session press the Set Button on the timer The time will go to the maximum time then count down The lamps will turn automatically You can decrease the time by pressing the Set Button To cancel a session press the Start Stop button on the timer The display will go to a 0 Checking Bed Hours Make sure the timer shows a 0 Press and hold both buttons The timer will flash two numbers then two other numbers pause two numbers pause etc These are the bed hours The first set of numbers are the thousands and hundreds digits for the bed hours The second set of numbers are the tens and ones digits for the bed hours For example if the display flashes the numbers 53 then 14 pauses then repeats then the total bed hours stored is 5314 The highest value that can be displayed is 9999 Automatic Shut off Timer Your tanning bed is equipped with an internal backup shut off timer which will automatically turn off your tanning system after 11 minutes This important safety feature prevents the user from resetting the timer before the end of the pre set maximum time interval Caring For and Maintaining Your Tanning Bed THE TANN
13. evice operating on that circuit breaker This tanning system requires a NEMA 5 15R Receptacle and a DEDICATED 15 Amp Circuit Breaker NEMA 5 15R Proper voltage is ONLY between 100 and 130 Volts ALL IMPROPER VOLTAGES MUST BE RECTIFIED WITH THE CORRECT BUCK BOOSTER TRANSFORMER Buck Boosters are available through your Tanning Bed Dealer Additionally a very easy way of protecting your tanning bed from potential electrical damage due to power surges or spikes is to UNPLUG the unit when NOT in use See power cord label to determine voltage and receptacle requirements Failure to comply with these electrical requirements will VOID ALL WARRANTIES and will damage electrical components WARNING HIGH LEAKAGE CURRENT ENSURE PROPER GROUNDING WARNING GROUNDING CIRCUIT CONTINUITY IS VITAL FOR SAFE OPERATION OF EQUIPMENT NEVER OPERATE WITH GROUNDING CONDUCTOR DISCONNECTED www mercola com 5 FOR ADDITIONAL ASSISTANCE PLEASE REVIEW THE HELPFUL SERVICE AND MAINTENANCE HINTS IN THIS USERS MANUAL IF YOU HAVE ADDITIONAL QUESTIONS REQUIRE TECHNICAL SUPPORT INTERESTED IN PURCHASING TANNING ACCESSORIES OR FUTURE UPGRADES FOR NEW LAMPS DO NOT HESITATE TO CONTACT THE AUTHORIZED DEALER WHERE YOU PURCHASED YOUR TANNING BED www mercola com Location Requirements Make sure the room size is at least 8 x 8 x 8 and is well ventilated Air from the room is used to cool your tanning bed wh
14. ged reflectors will reduce the tanning capability of the tanning unit Gently wipe the entire length of the lamp with a damp cloth to remove any film buildup Vacuum reflector area using a soft brush attachment How to Obtain Service 1 Review the Helpful Service Hints to follow 2 Ifyou require additional assistance contact the Customer Service Department at the Authorized Dealer where the bed was purchased If it becomes necessary to replace a warranty part proof of purchase is required to obtain warranty service It is important to keep your store receipt 3 For non warranty parts replacement for routine maintenance contact your Authorized Dealer 16 www mercola com Helpful Service Hints Lamps will not light Is the tanning bed on using the timer system Is the tanning bed plugged into the electrical receptacle Are the power cords securely connected from the canopy to bench Is your bed on a 15 Amp dedicated circuit breaker Check the power supply You may have to reset the circuit breaker This is due to not having a 15 Amp dedicated breaker or having too many devices on the proper breaker pulling too much amperage while tanning Verify that the voltage coming out of the wall is safe for this product Your voltage should not exceed 130 Volts The lamp may not be locked into place You may need to hand twist back into locking position The lamp may be burnt out Removal of the acrylic may be needed Refer to
15. h medication or it might be the result of non light related factors such as genetic factors pressure points or a fungus Common diseases which react unfavorably with UV light are exacerbated by UV e Herpes Simplex e Lupus Erythematosoyus swelling of the nerve endings e Porphyria severe extreme sensitivity to any source of light e Vitiligo irregularly shaped patches of skin with no pigmentation and dark borders e Skin cancers Basal Squamous and Melanoma www mercola com 19 Photosensitivity reactions may be triggered by medicines included in but not limited to the following general list This means you might turn red or burn when taking them with exposure to the sun or a tanning bed If you are taking any medication you should consult with your doctor before tanning Antibiotics in the Tetracycline Family Anticancer Drugs Anticonvulsants Antidepressants Antidiabetics Antihistamines Antihypertensive Medications Antiseptic Creams Birth Control Pills Retin A Sulfonamides often for urinary tract infections Tranquilizers Water Pills Medications to avoid when tanning Acne medications Antibacterial Drugs Antibiotics Anticancer Drugs Antidepressants Antihistamines Anti inflammatory Drugs Antiparasitic Drugs Birth Control Pills Diabetes Drugs Diuretics Psoralen Drugs topical or oral Tranquilizers Antipsychotic Drugs For more information on photosensitivity please see the following websites
16. ich helps to ensure years of trouble free performance Poor ventilation may cause the unit to overheat and cause discomfort to the user as well If any of the cooling fans malfunction turn off the tanning bed immediately and do not use it again until it has been serviced Place your tanning bed no closer than one foot from any wall Be sure that curtains drapes and other room furniture is not obstructing the airflow into the end caps of the bed or out of the fan openings Unpacking Instructions Your tanning bed comes in two cardboard cartons one for the bench and one for the canopy Remove the bench and canopy from the plastic bags The canopy box contains the canopy unit and pedestal The bench box contains bench unit users manual pillow and a hardware kit box containing legs arms safety goggles and assembly hardware Inspect the items including canopy and bench for any visible damage Report any such damage to your Authorized Dealer immediately Assembly Instructions Proper assembly of your tanning bed requires two people Tools r equir ed Assembling the tanning bed requires a inch wrench Parts List Item Description Quantity A eer Left Arm 798 7 1 Right Arm 1 BenchLeg eee 2 D Gas Shocks 2 E _ 5 16 x 1 Allen Bolt 4 1 Allen Wrench o 1 K Pedestal 3 Included Hardware E Allen Bolt I Allen Wrench www mercola com 7 Attaching Legs to Bench Figure la 0 00
17. llation Lamp Removal Lamp Cleaning and Replacement How to Obtain Service Helpful Service Hints Lamp Configuration Frequently Asked Questions Photosensitivity Pregnancy Record Your Warranty Information General Specifications Size Chart Warning Label Information Please read entire manual before attempting to operate this tanning unit www mercola com Safety Information Label Notice The United States FDA Food amp Drug Administration requires that a warning label is provided to inform the user of possible dangers as stated in 21 CFR Code of Federal Regulation part 1040 20 Review the information on this label located on the front of your tanning bed Tan smart and avoid overexposure If you do not tan in the sun you will not tan from this product As with natural sunlight overexposure can cause eye and skin injury and allergic reactions Allow 48 hours between sessions To ensure optimum smart tanning please refer to the recommended exposure time chart Refer to Table of Contents Use of certain medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult your physician before using any tanning bed if you are using medications or have a history of skin problems or believe you are sensitive to sunlight See Photosensitivity Refer to Table of Contents Recommended eyewear One pair of protective eyewear approved by the FDA is
18. lso have a slight redness and itching which occurs from getting too many UV rays It s dryness to the skin or reactions to cosmetics medications or foods that may contribute to this If a medication irritation cosmetic or food is causing the rash you should stop tanning until the rash disappears 18 www mercola com Photosensitivity A photosensitivity reaction does not depend on the presence or absence of a suntan or sunburn although it often accompanies them Photosensitivity reactions are immunological or toxicity reactions and result from the presence of photosensitizing agents and UV light Photosensitivity reactions are characterized by reddish skin with elevated poison ivy like bumps and can occur in areas that were not exposed to the sun They frequently produce little or no discomfort On the other hand phototoxic reactions another type of photosensitivity reaction are usually accompanied by symptoms similar to that of sunburn Once a person gets a photosensitivity reaction they are more likely to have a recurrence under the same conditions in the future Mayo Clinic 1993 Symptoms of Photosensitivity Usually severe burning Often occurs in patches and in small areas of the body Blotch formation This could be a result of heat as well as light Rash Photodermis Redness induced by light May be the cause of itching and may appear all over the body Uneven pigmentation Could be the result of light exposure combined wit
19. nning lamps are rated up to 1000 hours of use You may elect to change lamps sooner Step 1 Step 2 After removing acrylics grasp a lamp at one end and at middle Turn the lamp a quarter turn The lamp may then be gently removed from its holder Hold lamp with brand name label facing toward the acrylic and to the left side of the bed To install the lamp insert the pins located on the ends of the lamp into the slots on top of the lamp holder and turn the lamp a quarter turn to hold in place For lamp replacement refer to Lamp Cleaning section to follow Lamps used longer than 1000 hours have lost their tanning power even though they will continue to light www mercola com 15 The following lamp types have been certified by the United States FDA for use in your tanning system Solara Classic PN 532000 Solara Classic ReNew PN 532008 Solara Classic Infra Red PN 532007 Solara Classic ReFresh PN 532010 You may purchase tanning lamps from your authorized dealer Do not use lamps other than those specified To do so will void your warranty and FDA certification Lamp Cleaning amp Replacement Depending on the amount of usage it is recommended that you clean your lamps every six months To remove the acrylic see Table of Contents After all the lamps have been removed use a soft cloth and a non abrasive cleaner to wipe down the aluminum reflectors Take care not to scratch them because scratched or dama
20. nopy until both gas shocks have been installed www mercola com 9 Attaching Shocks Figure 1d Gas Shock Directions Figure 1d Step 1 While holding the gas shock barrel end up snap the ball end socket onto the top ball end of the canopy by pushing into place Step 2 Lift the canopy to the maximum open position and snap the ball end socket onto the bottom ball end of the bench by pushing into place Repeat for the second gas shock Attaching Pedestal Figure 2a gT 10 www mercola com Assembling Pedestal The pedestal is designed to cover the underside area and legs of the tanning bed The pedestal comes in three pieces 2 sides 1 front with Velcro affixed to the sides Begin by placing the smaller sections sides of the pedestal next to the legs with the Velcro towards the front Remove the Velcro film Place the front pedestal over the fronts of the pedestal sides and affix to the Velcro Electrical Connections Canopy Cord Bench Cord Dedicated 15Amp Circuit Breaker Making the Electrical Connections sce electrical requirements Refer to table of contents WARNING Be sure electrical power is disconnected before connecting the canopy to bench cables Step 1 Connect the canopy to the bench power cord located on the back of the unit Step 2 Plug the three prong 120VAC power cord into a 15 Amp dedicated outlet NOTE IT IS BEST TO UNPLUG THE TANNING BED
21. sions to achieve the results you want See recommended exposure time chart Do I have to take my contact lenses out before I tan No if you wear protective FDA approved eyewear Do I really have to wear Goggles Yes If you use a tanning bed without eye protection your eyes may be damaged by the UV rays FDA approved goggles that you wear are very important Your eyelids alone offer almost no protection against ultraviolet light which may cause damage to the eye Not using proper eye protection may also result in short term effects such as tired itchy eyes headaches and loss of night vision Nude Tanning Parts of the body that have never been exposed to the sun before will turn pink or even red They might even break out with a rash This is caused by an over exposure to the ultraviolet rays It takes these parts longer to start the tanning process Rashes Heat rashes tanner s itch indicate that the light and heat generated by tanning bulbs or the sun have dried your skin Itching can also result from a reduced rate of melanin production in a particular area of your body Melanin is the protective skin pigment found in varying amounts in everyone s skin If you begin tanning in the nude you may find that previously unexposed areas develop an itch This is natural so don t be alarmed just discontinue tanning for a few days and then slowly build up time allowing melanin production to increase Heat rashes may a
22. y should not be worn while tanning 14 www mercola com Acrylic Removal Canopy and Bench Acrylic Removal Warning Disconnect bed from electrical power before servicing Step 1 Step 2 Step 3 Step 4 Stand in front of bed Using a small flathead screwdriver insert the flat head into either end of the black acrylic trim strip Pry up slowly to grasp edge of strip and continue to pull away from unit until it is completely removed Repeat procedure for second strip of acrylic trim It may be necessary to slightly loosen the end cap screws to help remove the acrylic NEVER REMOVE END CAP SCREWS With the flathead screwdriver pry the acrylic up and over the lip in the bed rail It is recommended you have two people to remove acrylics Begin by grasping the long edges of the acrylic which are now exposed Standing in front of the bed grasp the long exposed edge of the acrylic and carefully slide it toward you until it is removed BE CAREFUL the edges of the acrylic may be sharp Acrylic Re installation Step 1 Step 2 Step 3 Place acrylic back on bed Tighten end cap screws Take one end of the black acrylic trim and press firmly onto the aluminum frame pushing into the opening The longer flat edge of the trim must be against the top of the acrylic Place the palm of your hand on the trim and apply pressure along the edge until the trim is firmly in place Lamp Removal amp Re installation The ta
Download Pdf Manuals
Related Search