Home

3-Space Sensor Data-Logging User`s Manual

1. Gyro scale 250 500 2000 sec selectable Gyro resolution 16 bit Gyro noise density 0 03 sec N Hz Gyro bias stability 25 C 11 hr average for all axes Gyro sensitivity 0 00875 sec digit for 250 sec 0 01750 sec digit for 500 sec 0 070 sec digit for 2000 sec Gyro non linearity 0 2 full scale Gyro temperature sensitivity 0 016 Compass scale 1 3 Ga default Up to 8 1 Ga available Compass resolution 12 bit Compass sensitivity 5 mGa digit Compass non linearity 0 1 full scale Specifications subject to change User s Manual 2 7 Physical Dimensions TSS DL Handheld Case TSS DL S Strapdown Case All dimensions in mm All dimensions in mm User s Manual 2 8 Axis Assignment All YEI 3 Space Sensor product family members have re mappable axis assignments and axis directions This flexibility allows axis assignment and axis direction to match the desired end use requirements The natural axes of the 3 Space Sensor are as follows The positive X axis points out of the right hand side of the sensor which is the side that is facing right when the buttons face upward and plug faces towards you The positive Y axis points out of the top of the sensor the side with the buttons e The positive Z axis points out of the front of the sensor the side opposite the plug The
2. Gyroscope Coefficients Determines the scale bias and cross axis parameters for the gyroscope Factory calibrated Accelerometer Enabled Determines whether the compass is enabled or not TRUE Compass Enabled Determines whether the accelerometer is enabled or not TRUE Gyroscope Enabled Determines whether the gyroscope is enabled or not TRUE Filter Mode Determines how orientation is filtered Kalman Calibration Mode Determines how raw sensor data is transformed into normalized data 1 Scale Bias Axis Directions Determines what natural axis direction each data axis faces X Y Z Sample Rate Determines how many samples the sensor takes per cycle 1 from each component sensor Running Average Percentage Determines how heavy of a running average to run on the final orientation running average Desired Update Rate Determines how long each cycle should take ideally 0 microseconds Reference Mode Determines how the accelerometer and compass reference vectors Single Auto determined RS232 Baud Rate Determines the speed of RS232 communication 115200 CPU Speed Determines how fast the CPU will run 60 MHz LED Color Determines the RGB color of the LED 0 0 1 Blue Joystick Enabled Determines whether the joystick is enabled or not TRUE Mouse Enabled Determines whether the mouse is enabled or not FALSE Button Gyro Disable Length Determines how many cycles the gyro
3. 3 Space Sensor 3 Space Sensor Data Logging Miniature Attitude amp Heading Reference System User s Manual YEI Technology 630 Second Street Portsmouth Ohio 45662 www YeiTechnology com www 3SpaceSensor com Patents Pending 2007 2011 Yost Engineering Inc Printed in USA 3 Space Sensor Data Logging Miniature Attitude amp Heading Reference System User s Manual YEI Technology 630 Second Street Portsmouth Ohio 45662 www YeiTechnology com www 3SpaceSensor com Toll Free 888 395 9029 Phone 740 355 9029 Patents Pending 2007 2011 Yost Engineering Inc Printed in US Table of Contents L Usage Safety Considerations E R R EEEE TE A EEEE TRES 1 1 Usage Conditions eroe E ONT em at 1 1 2 Technical Support atid Repairs eese recenset quiete deri tige E pesci eene seid 1 1 3 Battery Safety Considerations esses 2 2 Overview ofthe Y BI 3 Space Sensor ce sis tco tee M ae tele bee o be eo e e Sie Me ees 3 2 L Introductions uy eret te oe eei cae a e RED desto am eret eiiis 3 2 2 Applications etit ge aute eode RM a eet cea 3 2 3 Hardware Overview uui e n OR ENTRE EUG rer Ue eee ete E ter eH EU is 4 224 M 5 2 5 Block Diagram of Sensor Operation 6 2 6 SDeeifICcatlolsao eA
4. see command 251 in section 4 3 7 or the 3 Space Suite manual 3 4 Data Logging 3 4 1 Mass Storage Device The Data Logging 3 Space Sensor exposes the contents of its SD card to a computer by enumerating as a Mass Storage device in addition to a virtual COM port Upon being connected to a computer through USB the sensor will cease any current data logging session and will cede control of the SD card to the computer as both the computer and the sensor cannot write to the SD card without coming into conflict No further data logging can be done at this point until the computer no longer controls the SD card Unplugging the sensor will return control of the SD card to it Also the sensor has a Mass Storage Off mode which will return control of the SD card to it even while attached to a computer For more information on this see commands 57 and 58 in section 4 13 User s Manual 3 4 2 SD Card Format and Directory Structure The Data Logging 3 Space Sensor will attempt upon power on or upon SD card insertion to place the directory structure it requires on to the card If this is unsuccessful for any reason such as the card being in read only mode or the card having not been formatted yet the sensor s LED will pulse red twice quickly once a second It will also do this if no SD card is inserted at all This indicates that it is not ready to do data logging The SD card may be formatted in one of two ways either let any SD card for
5. Battery charge status byte 4 3 11 General Commands Command Description Long Description Return Data Len Return Data Details Data Len Data Details 196 0xc4 Set LED Mode Allows finer grained control over the sensor LED Accepts a single parameter that can be 0 for standard which displays all standard LED status indicators or 1 for static which displays only the LED color as specified by command 238 LED mode byte 200 0xc8 Read LED Mode Returns the current sensor LED mode which can be 0 for standard or 1 for static LED mode byte 223 0xdf Read firmware version string Returns a string indicating the current firmware version 12 Firmware version string 224 0xe0 Restore factory settings Return all non volatile flash settings to their original default settings 225 0xe1 Commit settings Commits all current sensor settings to non volatile flash memory which will persist after the sensor is powered off For more information on which parameters can be stored in this manner refer to Section 3 4 Sensor Settings 226 0xe2 Software reset Resets the sensor 227 0xe3 Enable watchdog timer Enables the onboard watchdog timer with the specified timeout rate If a frame takes more than this amount of time the sensor will automatically reset Timeout rate in microseconds int 228 0xe4 Disable watchdog timer
6. Disables the watchdog timer 229 0xe5 Enter bootloader mode Places the sensor into a special mode that allows firmware upgrades This will case normal operation until the firmware update mode is instructed to return the sensor to normal operation For more information ion upgrading firmware refer to the 3 Space Sensor Suite Quick Start Guide 230 0 6 Read hardware version string Returns a string indicating the current hardware version 32 Hardware version string 231 0xe7 Set UART baud rate Sets the baud rate of the physical UART This setting does not need to be committed but will not ake effect until the sensor is reset Valid baud rates are 1200 2400 4800 9600 19200 28800 38400 57600 115200 default 230400 460800 and 921600 Note that this is only applicable for sensor ypes that have UART interfaces Baud rate int 232 0xe8 Read UART baud rate Returns the baud rate of the physical UART Note hat this is only applicable for sensor types that have UART interfaces Baud rate int 233 0xe9 Set USB Mode Sets the communication mode for USB Accepts one value that can be 0 for CDC default or 1 for FTDI USB communication mode byte 234 0 Get USB Mode Returns the current USB communication mode USB communication mode byte 235 0xeb Set clock speed Sets the current processor clock speed Possible values are 15Mhz 30 Mhz
7. Only one file will be made in continuous mode named lt CaptureFileStub gt 1 txt in ASCII mode or lt CaptureFileStub gt 1 dat in binary CaptureDataMode The CaptureDataMode property in the capture cfg file specifies whether captured data is stored in the file as human readable ASCII or compact binary This property is one of the following ascii Data is logged in a human readable form Superfluous characters in the formatting string are placed in the data log binary Data is logged in a compact non human readable form Superfluous characters are ignored CaptureFilelnfoHeader The CaptureFileInfoHeader property in the capture cfg file determines whether a line should be written at the top of each capture file indicating the format of the data contained within This property can be set to either 0 for off or 1 for on 16 User s Manual 3 4 4 LED Capture Behavior The RGB LED can be used as an indicator of the current state of the sensor Below is a summary of the LED meanings Solid Blue or solid currently set custom color setting Power on and no data logging session in progress Yellow A data logging session is in progress but a sample is not currently being taken Green The LED will emit a green flash and return to yellow when a data logging sample is taken Red double pulse MicroSD media not present or file system error Red Single Pulse when not plugged into USB Ba
8. byte 252 0xfc Read mouse absolute relative mode Return the current mouse absolute relative mode Note that if the sensor has not been reset since it has been put in this mode the mouse will not reflect this change yet even though the command will 1 Absolute or relative mode byte 253 0xfd Set joystick and mouse present removed Sets whether the joystick and mouse are present or removed The first parameter is for the joystick and can be 0 for removed or 1 for present The second parameter is for the mouse If removed they will not show up as devices on the target system at all For these changes to take effect the sensor driver may need to be reinstalled Joystick present removed byte Mouse present removed byte 254 0xfe Get joystick and mouse present removed Returns whether the joystick and mouse are present or removed Joystick present removed byte Mouse present removed byte 33 User s Manual Appendix USB Connector The 3 Space Sensor has a 5 pin USB Type B jack and can be connected via a standard 5 pin mini USB cable Hex Decimal Conversion Chart Second Hexadecimal digit 0 1 2 3 4 3 6 7 8 9 C D E Ip 0 000 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 1 016 017 018 019
9. orientation This is an advanced command that is best used through 3 Space Sensor Suite calibration utilities For more information please refer to the 3 Space Sensor Suite Quick Start Guide 105 0x69 Set reference vector mode Set the current reference vector mode Parameter can be 0 for single static mode which uses a certain reference vector for the compass and another certain vector for the accelerometer at all times 1 for single lauto mode which uses 0 1 0 as the reference vector for the accelerometer at all times and uses the average angle between the accelerometer and compass to calculate the compass reference vector once upon initiation of this mode 2 for single auto continuous mode which works similarly to single auto mode but calculates this continuously or 3 for multi reference mode which uses a collection of reference vectors for the compass and accelerometer both and selects which ones to use before each step of the filter Mode Byte Pin Byte 106 0x6A Set oversample rate Sets the number of times to sample each component sensor for each iteration of the filter This ican smooth out readings at the cost of performance If this value is set to 0 or 1 no oversampling occurs otherwise the number of samples per iteration depends on the specified parameter up to a maximum of 10 This setting can be saved to non volatile flash memory using the Commit Settings command Samples Per Iterat
10. Details Len Data Details Read tared orientation as Returns the filtered tared orientation estimate in 0 0 00 quaternion quaternion form 16 Quaternion float x4 0 Read tared orientation as Returns the filtered tared orientation estimate in 1 0x01 leuler angles leuler angle form 12 Euler Angles float x3 0 Read tared orientation as Returns the filtered tared orientation estimate in 2 0 02 rotation matrix rotation matrix form 36 Rotation Matrix float x9 0 Read tared orientation as Returns the filtered tared orientation estimate in 3 0x03 axis angle axis angle form 16 Axis float x3 Angle float 0 Returns the filtered tared orientation estimate in two Read tared orientation as vector form where the first vector refers to forward Forward Vector float x3 4 0x04 two vector and the second refers to down 24 Down Vector float x3 0 Returns the difference between the measured 5 0x05 Read difference quaternion orientation from last frame and this frame 16 Quaternion float x4 0 Read untared orientation Returns the filtered untared orientation estimate in 0x06 las quaternion quaternion form 16 Quaternion float x4 0 Read untared orientation Returns the filtered untared orientation estimate in 7 0x07 as euler angles euler angle form 16 Euler Angles float x3 0 Read untared orientation Returns the filtered untared orientation estimate in 8 0 08 rotation matrix rotation matrix form 36 Rotation Matrix float x9 0 Read untar
11. a 1 places the sensor into a confidence based running average mode which changes the running average factor based upon the confidence factor which is a measure of how in motion the sensor is This setting can be saved to non volatile flash memory using the Commit Settings command Mode Byte 125 0x7d Set gyroscope range Only parameter is the new gyroscope range which can be 0 for 250 DPS 1 for 500 DPS or 2 for 2000 DPS Default range Higher ranges can detect and report larger angular rates but are not as accurate for smaller angular rates This setting can be saved to non volatile flash memory using the Commit Settings command Gyroscope range setting Byte 126 0x7e Set compass range Only parameter is the new compass range which can be 0 for 0 88G 1 for 1 3G Default range 2 for 1 9G 3 for 2 5G 4 for 4 0G 5 for 4 7G 6 for 5 6G or 7 for 8 1G Higher ranges can detect and report larger magnetic field strengths but are not as accurate for smaller magnetic field strengths This setting can be saved to non volatile flash memory using the Commit Settings command Compass range setting Byte 28 User s Manual 4 3 8 Configuration Read Commands Return Data Command Description Long Description Data Len Return Data Details Len Data Details Read t
12. com Support is provided for the lifetime of the equipment Requests for repairs should be made through the Support department For damage occurring outside of the warranty period or provisions customers will be provided with cost estimates prior to repairs being performed User s Manual 1 3 Battery Safety Considerations 4 RGB Indicator LED 5 Input Button 2 3 Input Button 1 6 MicroSD Card Slot 2 Recessed Power Switch 1 USB Connector The Data logging 3 Space Sensor contains a rechargeable lithium polymer battery Lithium polymer batteries have high energy densities and can be dangerous if not used and cared for properly The Data Logging 3 space Sensor has been designed to include multiple levels of battery safety assurance The Data Logging 3 Space Sensor circuitry includes smart charging circuitry with thermal management to prevent over charging the battery The battery pack itself also includes protection circuitry to prevent over charge over voltage over current and over discharge conditions Most battery issues arise from improper handling of batteries and particularly from the continued use of damaged batteries As with any lithium polymer battery powered device the following should be observed Don t disassemble crush puncture shred or otherwise attempt to change the form of your battery Don t attempt to change
13. default range scaling to raw data readings Also applies a bias offset to raw data the values of which are taken from the provided calibration parameters command See section 4 3 7 for more information Bias Scale Mode The default calibration mode Applies default range scaling to raw data readings Also applies a bias offset to the raw data as well as an additional scale matrix Uses the matrix and vector portions from the provided calibration parameters command Ortho Calibration Mode A more advanced calibration mode that requires initial setup steps Please refer to the 3 Space Suite Quick Start Guide for information on how to supply ortho calibration data Uses 24 orthogonal data points to provide accelerometer and compass correction factors for enhanced orientation accuracy 3 1 4 Reference Vectors In order to get an absolute estimation of orientation from the accelerometer and compass the sensor needs a reference vector for each to compare to the data read from it The most obvious choice for these are the standard direction of gravity down and the standard direction of magnetic force north respectively However the sensor does provide several different modes for determining which reference vector to use Single Manual Uses 2 reference vectors it is given as the reference vectors for the accelerometer and compass Single Auto When the sensor powers on or is put into this mode it calculates gravity and north and uses those c
14. is ignored after a button is 5 pressed 18 User s Manual Multi Reference Weight Power Determines what power each multi reference vector weight is raised to 0 Multi Reference Cell Divisions Determines how many cells the multi reference lookup table is divided 4 into per axis Multi Reference Nearby Vectors Determines how many nearby vectors each multi reference lookup table 8 cell stores 3 5 4 Capture Settin gs and Defaults Setting Name Purpose Default Value Capture Rate Determine how often to capture data in ms 10 Capture Format Determine what data to capture d Yt oq Date time and orientation as quaternion Start Event Determine how a session is started left button Start Event Motion Threshold Determine how much motion starts a session in g 0 5 Capture Style Determine when to capture data continuous Periodic Capture Time Determine how long to capture data in a period in ms 5000 Periodic Rest Time Determine how long to rest in a period in ms 5000 Stop Event Determine how a session is stopped right button Stop Event Motion Threshold Determine how much motion stops a session in g 0 3 Stop Event Capture Count Determine how many captures to perform before stop 100 Stop Event Capture Duration Determine how long to capture before stop in ms 5000 Stop Event Per
15. of 1 to 1 the scale would be 500 Bias is how far the center of the data readings 1s from 0 If another compass read from 200 to 900 on the x axis the bias would be 350 and the scale would be 550 The last parameter used in turning this component sensor data into usable data is cross axis effect This is the tendency for a little bit of data on one axis of a sensor to get mixed up with the other two This is an effect experienced by the accelerometer and compass There are 6 numbers for each of these one to indicate how much each axis is affected by each other axis Values for these are generally in the range of 1 to 1096 These parameters are applied in the following order 1 Bias is added to each axis 2 The three axes are treated as a vector and multiplied by a matrix representing scale and cross axis parameters Factory calibration provides default values for these parameters for the accelerometer and compass and users should probably never need to change these values To determine these parameters for the gyroscope you must calibrate it Read the Quick Start guide or the 3 Space Suite manual for more information on how to do this 10 User s Manual 3 1 3 Additional Calibration The 3 Space Sensor provides multiple calibration modes that can improve performance at the cost of additional setup and calibration routines For more information on setting these additional modes please refer to command 169 Bias Mode Applies
16. or modify the battery yourself Contact Y EI technical support for battery replacement or battery repair Don t let the mobile device or battery come in contact with water or other liquids Don t allow the battery to touch metal objects Don t place the sensor unit near a heat source Excessive heat can damage the sensor unit or the battery High temperatures can cause the battery to swell leak or malfunction Don t dry a wet or damp sensor unit with an appliance or heat source such as a hair dryer or microwave oven Don t drop the sensor unit Dropping especially on a hard surface can potentially cause damage to the sensor unit or the battery Discontinue use immediately and contact YEI technical support if the battery or sensor unit produce odors emit smoke exhibit swelling produce excess heat exhibit leaking Dispose of Lithium polymer batteries properly in accordance with local state and federal guidelines User s Manual 2 Overview of the YEI 3 Space Sensor 2 1 Introduction The YEI 3 Space Sensor Data Logging integrates a miniature high precision high reliability Attitude and Heading Reference System AHRS with a MicroSD card interface and a rechargeable lithium polymer battery solution into a single low cost end use ready unit The Attitude and Heading Reference System AHRS uses triaxial gyroscope accelerometer and compass sensors in conjunction with advanced on board filtering and processing algor
17. 020 021 022 023 024 025 026 027 028 029 030 031 2 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 3 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 4 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 5 5 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 6 096 097 098 099 100 101 102 103 104 105 06 107 108 09 10 111 7 12 113 114 15 116 117 118 119 120 121 22 123 124 25 26 127 8 28 129 130 31 132 133 134 135 136 137 38 139 140 41 42 143 z 9 44 145 146 47 148 149 150 151 152 153 54 155 156 57 58 159 60 161 162 63 164 165 166 167 168 169 70 171 172 73 74 175 76 177 178 79 180 181 182 183 184 185 86 187 188 89 90 191 92 193 194 95 196 197 198 199 200 201 202 203 204 205 206 207 D 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 F 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 34 Notes Serial Number User s Manual 36 Technology YEI Technology 630 Second Street Portsmouth Ohio 45662 Toll Free 888 395 9029 Phone 740 355 9029 www YeiTechnology com www 3SpaceSensor com Patents Pendin 2007 2011 Yost Engineering Inc Printed in USA
18. a as soon as it can After this one session it will not attempt to start another session e left button right button and both buttons A session will begin when the appropriate button or buttons are pressed Note that if the stop condition is set to the same set or part of the same set of buttons the buttons will need to be released before they will register as a stop condition motion A session will begin when the accelerometer detects that motion has risen to a certain level This level is given in gs gravity units and can be set through the property CaptureStartEventMotionThreshold 14 User s Manual CaptureStopEvent The CaptureStopEvent property in the capture cfg file selects options for stopping a capture session Possible values for the CaptureStopEvent property are on command Like the same property for the start events this means a session can only be stopped through a command Use command 61 for ending a data logging session Also note that regardless of stop event this command can be used to stop a data logging session always This will always stop a data logging session as soon as it starts This is most useful in concert with the CapturePostStopGatherTime property which gives a length of time after the stop of a session data should continue to be logged e left button right button and both buttons Just as for start events these will stop a session when t
19. alculated vectors as the reference vectors Single Auto Continual The same as Single Auto but the calculation happens constantly This can account for some shifts in magnetic force due to nearby objects or change of location and also can help to cope with the instability of the accelerometer Multiple Uses a set of reference vectors from which the best are picked each cycle to form a single final reference vector This mode has the ability to compensate for certain errors in the orientation In this mode the sensor will have a slightly slower update rate but will provide greater accuracy For information on how to set up this mode see the Quick Start guide or the 3 Space Suite manual 3 1 5 Orientation Filtering The 3 Space Sensor provides several different modes for providing orientation estimation Note also that IMU data collection rate is bound to the update rate of the filter For more information on setting these additional modes please refer to command 123 Kalman Filter The default filter mode Normalized sensor data and reference vectors are fed into the Kalman filter which uses statistical techniques to optimally combine the data into a final orientation reading Provides the highest accuracy orientation at the lowest performance Alternating Kalman Filter Uses the same Kalman filter as before but skips every other update step Slightly less accurate than the Kalman filter but faster Complementary Filter Fuses low pass f
20. any random collection of axes and buttons that isn t a mouse or keyboard Joysticks are mostly used for games but can also be used for simulation robot controls or other applications The 3 Space Sensor as a joystick should appear just like any other joystick to an operating system that supports USB HID which most do 3 3 3 Mouse When acting as a mouse the 3 Space Sensor will take control of the system s mouse cursor meaning if the mouse portion is not properly calibrated using it could easily leave you in a situation in which you are unable to control the mouse cursor at all In cases like this unplugging the 3 Space Sensor will restore the mouse to normal operation and unless the mouse enabled setting was saved to the sensor s memory plugging it back in should restore normal operation Using the default mouse settings caution should be exercised in making sure the orientation estimate 1s properly calibrated before turning on the mouse For help with this see the Quick Start guide The mouse defaults to being in Absolute mode which means that the data it gives is meant to represent a specific position on screen rather than an offset from the last position This can be changed to Relative mode where the data represents an offset In this mode the data which would have indicated the edges of the screen in Absolute mode will now represent the mouse moving as quickly as it can in the direction of that edge of the screen For more information
21. are orientation as 128 0x80 Returns the current tare orientation as a quaternion 16 Quaternion float x4 0 Read tare orientation as Returns the current tare orientation as a rotation 129 0x81 rotation matrix matrix 36 Rotation Matrix float x9 0 Returns the current accelerometer rho mode as well as the value If this mode is set to O static this will return the rho mode the static rho value and then a dummy value of 0 If this mode is set to 1 this will Accelerometer rho mode Read accelerometer rho return the rho mode and the minimum and byte Accelerometer rho 130 0x82 value maximum rho values 9 values float x2 0 Returns the current compass rho mode as well as the value If this mode is set to 0 static this will return the rho mode the static rho value and then a dummy value of 0 If this mode is set to 1 this will Compass rho mode byte return the rho mode and the minimum and Compass rho values float 131 0x83 Read compass rho value maximum rho values 9 x2 0 Reads the amount of time taken by the last filter Last update time in 132 0x84 Read current update rate update step 4 microseconds int 0 Reads the current compass reference vector Note Read compass reference this is not valid if the sensor is in Multi Compass reference vector 133 0x85 vector Reference Vector mode 12 float x3 0 Reads the current compass reference vector Note Read accelerometer that this is not valid if the sensor
22. byte 0 Returns a value indicating whether the accelerometer Read accelerometer contribution is currently part of the orientation Accelerometer enabled 141 0x8d enabled state estimate O for off 1 for on 1 value byte 0 Returns a value indicating whether the compass Read compass enabled contribution is currently part of the orientation Compass enabled value 142 0x8e state estimate 0 for off 1 for on 1 byte 0 Returns a value indicating the current axis direction setup For more information on the meaning of this value please refer to the Set Axis Direction 143 0x8f Read axis direction byte command 116 1 Axis direction value byte 0 Returns a value indicating how many times each component sensor is sampled before being stored as raw data A value of 1 indicates that no oversampling is taking place while a value that is higher indicates the number of samples per 144 0x90 Read oversample rate component sensor per filter update step 1 Oversample rate byte 0 Returns a value indicating how heavily the orientation estimate is based upon the estimate from the previous frame For more information on the meaning Read running average lof this value please refer to the Set Running Average Running average percent 145 0x91 percent Percent command 117 4 float 0 Returns the current desired update rate Note that this value does not indicate the actual update rate but instead indicates the value that should be spent idling the ma
23. e 3 Space Sensor will not work properly in outer space or on planets with no magnetic field Care should be taken when using the 3 Space Sensor in a car or other moving vehicle as the disturbances caused by the vehicle s acceleration may cause the sensor to give inaccurate readings e Because of its reliance on a compass care should be taken when using the 3 Space Sensor near ferrous metal structures magnetic fields current carrying conductors and should be kept about 6 inches away from any computer screens or towers Since the Data Logging 3 Space Sensor uses removable MicroSD media it is end user s responsibility to ensure that storage media is compatible e The Data Logging 3 Space Sensor is powered by a rechargeable lithium polymer battery Lithium polymer batteries have high energy densities and can be dangerous if not used properly See section 1 4 Battery Considerations for further information pertaining to battery safety 1 2 Technical Support and Repairs Limited Product Warranty YEI warrants the media and hardware on which products are furnished to be free from defects in materials and workmanship under normal use for sixty 60 days from the date of delivery No warranties exist for any misuse YEI will repair or replace any defective product which is returned within this time period Product Support YEI provides technical and user support via our toll free number 888 395 9029 and via email support YostEngineering
24. e Strapdown Sensor Unit Dimensions 35mm x 60mm x 15mm 1 38 x 2 36 x 0 59 in Weight 28 grams 0 98 oz Supply voltage 5v USB Battery technology rechargeable Lithium Polymer Battery lifetime 5 hours continuous use at full performance Communication interfaces USB 2 0 Mass Storage amp CDC MicroSD card configuration files Storage media MicroSD card Filter update rate up to 200Hz with full functionality up to 800Hz in IMU mode Orientation output absolute amp relative quaternion Euler angles axis angle rotation matrix two vector Other output raw sensor data corrected sensor data normalized sensor data temperature date time Shock survivability 5000g Temperature range 40C 85C 40F 185F Processor 32 bit RISC running 60MHz Sensor Orientation range 360 about all axes Orientation accuracy 2 for dynamic conditions amp all orientations Orientation resolution lt 0 08 Orientation repeatability 0 085 for all orientations Accelerometer scale 2g 4g 80 selectable Accelerometer resolution 14 bit Accelerometer noise density 99ug Y Hz Accelerometer sensitivity 0 00024g digit for 2g range 6g range for HH 0 00048g digit for 4g range 12g range for HH 0 00096g digit for 8g range 245 range for HH Accelerometer temperature sensitivity 0 008
25. e in the orientation fusion algorithm For best results each of the 24 orientations should be filled in with component sensor data Note also that ortho calibration data will not be used unless the calibration mode is set to Ortho Calibration For more information refer to Section 3 1 3 Additional Calibration Intended for ladvanced users 175 0xaf Clear ortho calibration data Clear out all ortho lookup table data Intended for advanced users 31 User s Manual 4 3 10 Battery Commands Command Description Long Description Return Data Len Return Data Details Data Len Data Details 201 0 9 Read battery voltage Read the current battery level in volts Note that this value will read as slightly higher than it actually is if it is read a USB connection Battery level in voltage float 202 0 Read battery percent remaining Read the current battery lifetime as a percentage of the total Note that this value will read as slightly higher than it actually is if it is read a USB connection Battery level as percent short 203 0xcb Read battery status Returns a value indicating the current status of the battery which can be a 3 to indicate that the battery is currently not charging a 2 to indicate that the battery is charging and thus plugged in or a 1 to indicate that the sensor is fully charged
26. e value is multiplied This setting can be saved to non volatile flash memory using the Commit Settings command 48 Bias float x3 Matrix float x9 162 0xa2 Read compass calibration coefficients Return the current compass calibration parameters 48 Bias float x3 Matrix float x9 163 0xa3 Read accelerometer calibration coefficients Return the current accelerometer calibration parameters 48 Bias float x3 Matrix float x9 164 0xa4 Read gyroscope calibration coefficients Return the current gyroscope calibration parameters 48 Bias float x3 Matrix float x9 165 0xa5 Begin gyroscope auto calibration Performs auto gyroscope calibration Sensor should remain still while samples are taken The gyroscope bias will be automatically placed into the bias part of the gyroscope calibration coefficient list 166 0xa6 gyroscope calibration coefficients Sets the current gyroscope calibration parameters to the specified values These consist of a bias which is added to the raw data vector and a matrix by which the value is multiplied This setting can be saved to non volatile flash memory using the Commit Settings command 48 Bias float x3 Matrix float x9 169 0xa9 Set calibration mode Sets the current calibration mode which can be 0 for Bias 1 for Scale Bias and 2 for Ortho Calibration For more information refer to section 3 1 3 Addi
27. ecomes less trusted Gyroscope This sensor measures angular motion It has no ability to give any absolute orientation information like the accelerometer or compass and so is most useful for correcting the orientation during sensor motion Its role during these times becomes vital though as the accelerometer readings can become unreliable during motion Compass This sensor measures magnetic direction The readings from the compass and accelerometer are used together to form the absolute component of orientation which is used to correct any short term changes the gyroscope makes Its readings are much more stable than those of the accelerometer but it can be adversely affected by any ferrous metal or magnetic objects When the accelerometer is less trusted the compass is treated in the same way so as to avoid updates to orientation based on partial absolute information 3 1 2 Scale Bias and Cross Axis Effect The readings taken from each component sensor are not in a readily usable form The compass and accelerometer readings are not unit vectors and the gyroscope readings aren t yet in radians per second To convert them to these forms scale and bias must be taken into account Scale is how much larger the range of data read from the component sensor is than the range of data should be when it is converted For example if the compass were to give readings in the range of 500 to 500 on the x axis but we would like it to be in the range
28. ed orientation Returns the filtered untared orientation estimate in 9 0 09 axis angle axis angle form 16 Axis float x3 Angle float 0 Returns the filtered untared orientation estimate in Read untared orientation two vector form where the first vector refers to north North Vector float x3 10 0x0A as two vector land the second refers to gravity 24 Gravity Vector float x3 0 Returns the filtered tared orientation estimate in two vector form where the first vector refers to forward and the second refers to down These vectors are Read tared two vector in given in the sensor reference frame and not the Forward Vector float x3 11 0x0B sensor frame global reference frame 24 Down Vector float x3 0 Returns the filtered tared orientation estimate in two vector form where the first vector refers to forward and the second refers to down These vectors are Read untared two vector in given in the sensor reference frame and not the North Vector float x3 12 0x0C sensor frame global reference frame 24 Gravity Vector float x3 0 23 User s Manu al 4 3 2 Normalized Data Commands Return Data Command Description Long Description Data Len Return Data Details Len Data Details Returns the normalized gyro rate vector laccelerometer vector and compass vector Note that the gyro vector is in units of radians sec while the lacce
29. ell divisions as an example multi reference mode by default only handles orientations reachable by successive rotations of ninety degrees about any of the three axes and hence has a resolution of 4 360 4 90 Thus a resolution of 8 would provide rotations of forty five degrees about any of the three axes 360 8 45 The second parameter indicates the number of adjacent vectors that will be checked for each In addition the number of checked vectors can be adjusted as well The second parameters refers to the number of adjacent reference vectors that are averaged to produce the final reference vector for the particular orientation up to a maximum of 32 Intended for advanced users Resolution Byte Number of Check Vectors Byte 112 0x70 Set compass mulfi reference vector Directly set the multi reference compass vector at the specified index First parameter is index second parameter is compass vector Intended for advanced users 13 Index Byte Compass Reference Vector float x3 113 0 71 Set compass multi reference check vector Set the compass reading to be used as a check vector to determine which cell index to draw the reference vector from First parameter is an index second parameter is the compass vector Intended for advanced users 13 Index Byte Compass Check Vector float x3 114 0x72 Set accelerometer multi reference vector Directly set the multi re
30. eo n Oei eb edite eee te DA EN aa 7 257 Physical Dimensions xe i et E 8 2 8 Axis Assignment eic sei ete ted hese eed dives ete e HR n I reo teint 9 3 Description of the 3 S pace Sensor s SER P dte Re ER MATS 10 3 1 Orientation Estimation i te f nero rede ee D E rec eie e ae P RR Da aa verte cedit ener ice leo 10 3 11 Component SensOrg eret er oe eet Een tro eere er enar ye gine eS ee ER EN e rr rede teet ie ee et eoe e re edere 10 3 12 Scale Bias and Cross Axis Effect sioe se Ihe ane SS IGNI is 10 3 1 3 Additional Calibratiori ete E RE S BER ERU EUG 11 3 154 Reference Vector ase rrt a E RETURN D RE UU NURSE 11 3 1 5 Onientation eec dene eire e e UNS ores debet 11 3 1 6 Reference 12 3 17 Other Estimation Parameters ce eee e tei tees edi e D ve ete 12 32 Communications eai e Um e Re E AEG REO E RE sa qaq 13 3 3 Input Device Emulatiofi uir ete EY RHET REST e ON eL p PI Wc e ter cs dieta 13 3 3 I Axes and Buttons uto CR Urat das get eene ms dedere 13 3 3 2 Joystick iioi a d ee edema avg eee i e e va id i Wayana 13 3 3 3 E M 13 3 4 Data Loggg e E RE SE TE UR UE ERE REG v ee 13 341 Mass Storage De
31. es during a data logging session In periodic mode data logging will start and stop during the course of a session The properties that control this behavior are CaptureStylePeriodicCaptureTime which determines how long it captures for before it stops and CaptureStylePeriodicRestTime which determines how long it is stopped before it starts capturing again CapturePostStopGatherTime The CapturePostStopGatherTime property in the capture cfg file specifies an amount of time after a session has stopped to continue gathering data This value is specified in milliseconds CaptureFileStub The CaptureFileStub property in the capture cfg file specifies the base name of the data logging file which resides in each session s directory with a txt appended to it if data is captured in ASCII mode and dat if in binary mode With a CaptureFileMode of new this stub will also have a number added on to it before the txt or dat CaptureFileMode The CaptureFileMode property in the capture cfg file specifies how files are used to capture data This property 1s one of the following append New samples are added to the end of the single data log in the session directory replace In continuous mode the same as append In periodic mode only data from the most recent period will appear new A new file will be made for each data capture period and each period s data will be placed in this new file
32. ference accelerometer vector at the specified index First parameter is index second parameter is compass vector Intended for ladvanced users 13 Index Byte Accelerometer Reference Vector float x3 115 0x73 Set accelerometer multi reference check vector Set the accelerometer reading to be used as a check vector to determine which cell index to draw the reference vector from First parameter is an index second parameter is the accelerometer vector Intended for advanced users 13 Index Byte Accelerometer Check Vector float x3 116 0x74 Set axis directions Sets alternate directions for each of the natural axes lof the sensor The only parameter is a bitfield representing the possible combinations of axis swapping The lower bits specify which axis each lof the natural axes will be read as 000 XYZ standard operation 001 XZY 002 YXZ 003 YZX 004 ZXY 005 ZYX For example using XZY means that whatever value appears as Y on the natural axes will now be the Z component of any new data and vice versa The 3 bits above those are used to indicate which axes if any should be reversed If it is cleared the axis will be pointing in the positive direction Otherwise the axis will be pointed in the negative direction Note These are applied to the axes after the previous conversion takes place Bit 4 Positive Negative Z Third resulting component Bit 5 Positive Negat
33. guide or 3 Space Suite manual Any changes relating to the multiple reference vector mode are an exception to this rule as all these changes are saved immediately 3 5 2 Natural Axes The natural axes of the 3 Space Sensor are as follows The positive X axis points out of the right hand side of the sensor which is the side that is facing right when the buttons face upward and plug faces towards you The positive Y axis points out of the top of the sensor the side with the buttons e The positive Z axis points out of the front of the sensor the side opposite the plug Bear in mind the difference between natural axes and the axes that are used in protocol data While they are by default the same they can be remapped so that for example data axis Y could contain data from natural axis X This allows users to work with data in a reference frame they are familiar with See section 2 8 for a diagram illustrating the natural axes 3 5 3 Sensor Settings and Defaults Setting Name Purpose Default Value Accelerometer Rho Value Determine how trusted the accelerometer is Confidence Mode 5 to 100 Compass Rho Value Determine how trusted the compass is Confidence Mode 5 to 100 Accelerometer Coefficients Determines the scale bias and cross axis parameters for the Factory calibrated accelerometer Compass Coefficients Determines the scale bias and cross axis parameters for the compass Factory calibrated
34. he buttons are pressed motion stop This will stop a session when the motion falls below a certain threshold This threshold given in gs gravity units is indicated by the property CaptureStopEventMotionThreshold capture count This will stop a session after a certain number of samples have been taken This number is given by the property CaptureStopEventCaptureCount capture duration This will stop a session after it has lasted for a certain amount of time given in milliseconds by the property CaptureStopEventCaptureDuration period count This only has any effect when the CaptureStyle property is set to periodic It will stop a capture after a certain number of capture periods given by the property CaptureStopEventPeriodCount Using this when in continuous mode will cause the session to never end CaptureFormat Th CaptureFormat property specifies a format string similar to that required by the C function printf It consists of a string of whatever characters are desired to show up in the data logging file in addition to a number of delimited tokens which indicate data of a certain type Options for characters which may follow the are as follows d The current date t The current time q The tared orientation in quaternion form a The tared orientation in axis angle form e The tared orientation in Euler angle form given in pitch yaw roll order m The tared orientation in rota
35. he left of an equals sign and then change the value for it on the right of the equals sign If the value is textual properties where this is the case will have a list of the possible values listed to the right of the assignment be sure to enclose the text in quotes Quotes are not necessary for numeric values 3 4 3 Data Logging As described in section 3 4 2 upon the start of a data logging session a new directory will be created to hold the data named after the time the session was started given by the real time clock see section 3 4 4 The following sections describe the configuration properties that determine data logging capture behavior CaptureStartEvent The CaptureStartEvent property in the capture cfg file selects options for starting a capture session Possible values for the CaptureStartEvent property are on command This setting has no way of starting a capture session except through the calling of the begin data logging session command command 60 See section 4 for more information on this command Because calling a command requires a USB connection which can communicate with the sensor the sensor will have to be taken out of Mass Storage mode before this command is called The command to turn off Mass Storage mode is command 58 Also note that regardless of start event this command can be used to start a data logging session startup Whenever the sensor starts up it will attempt to start logging dat
36. he protocol can be used through the USB port A complete description of how to use this protocol is given in section 4 of this document Also you may instead use the 3 Space Suite which provides a graphical method to do the same To learn how to use this read the 3 Space Suite manual In addition data logging options allow the sensor to be configured to log data in certain formats with various criteria for beginning and ending a data logging session These options and working with the data logging system 1s covered in section 3 4 of this document 3 3 Input Device Emulation 3 3 1 Axes and Buttons The 3 Space Sensor has the ability to act as a joystick and or mouse Both of these are defined in the same way as collection of axes and buttons Axes are input elements that can take on a range of values whereas buttons can only either be on or off On a joystick the stick part would be represented as 2 axes and all the physical buttons on it as buttons The 3 Space Sensor has no physical Joystick and only 2 physical buttons so there are a number of options to use properties of the orientation data as axes and buttons Each input device on the 3 Space Sensor has 2 axes and 8 buttons For more information on setting these up see the 3 Space Suite manual All communication for these input devices 1s done through the standard USB HID Human Interface Device protocol 3 3 2 Joystick As far as a modern operating system is concerned a joystick is
37. iltered accelerometer compass data with high pass filtered gyroscope data to provide an orientation estimate Less accurate than any Kalman filtering techniques but provides significantly higher performance IMU Mode Performs no orientation filtering but allows IMU data to be read at the maximum update rate of 800 Hz 11 User s Manual 3 1 6 Reference Orientation Taring Given the results of the Kalman filter the sensor can make a good estimation of orientation but it will likely be offset from the actual orientation of the device by a constant angle until it has been given a reference orientation This reference orientation tells the sensor where you would like its zero orientation to be The sensor will always consider the zero orientation to be the orientation in which the plug is facing towards you and top the side with buttons on it facing up The sensor must be given a reference orientation that represents the orientation of the sensor when it is in the position in which you consider the plug to be towards you and the buttons up The act of giving it this reference orientation to the sensor is called taring just as some scales have a tare button which can be pressed to tell the scale that nothing is on it and it should read zero For instructions on doing this refer to the Quick Start guide or 3 Space Suite manual 3 1 7 Other Estimation Parameters The 3 Space Sensor offers a few other parameters to filter the orientatio
38. in loop Thus without having set a specified desired update rate this value should read Desired update rate in 146 0x92 Read desired update rate 0 4 microseconds int 0 Read Kalman filter 147 0x93 covariance matrix Return the current Kalman filter covariance matrix 36 Covariance matrix float x9 0 Return the current accelerometer measurement range which can be a 0 for 2g 1 for 4g or a 2 for Accelerometer range 148 0x94 Read accelerometer range 8g 1 setting byte 0 Read multi reference mode Read weighting power for multi reference vector 149 0x95 power weight weights Intended for advanced users 4 Weight float 0 29 User s Manual Return Data Command Description Long Description Data Len Return Data Details Len Data Details Reads number of cell divisions and number of nearby vectors per cell for the multi reference vector lookup table For more information on these values please Number of cell divisions Read multi reference refer to the Set Multi Reference Resolution byte number of nearby 150 0x96 resolution command 111 Intended for advanced users 2 vectors byte 0 Read number of multi Reads the total number of multi reference cells 151 0x97 reference cells Intended for advanced users 4 Number of cells int 0 Returns the current filter mode which can be 0 for IMU mode 1 for Kalman 2 for Alternating Kalman or 3 for Complementary For more informa
39. iod Count Determine how many periods before stopping 1 Post Stop Gather Time Determine how long to capture after stop 0 File Stub Determine name of data log data File Mode Determines how to put data in files append Data Mode Determines how data is written ascii File Info Header Enabled Determines whether or not to have a file header 19 User s Manual 4 3 Space Sensor Usage Protocol 4 1 Usage Overview 4 1 1 Protocol Overview The 3 Space Sensor receives messages from the controlling system in the form of sequences of serial communication bytes called packets For ease of use and flexibility of operation two methods of encoding commands are provided binary and text Binary encoding is more compact more efficient and easier to access programmatically ASCII text encoding is more verbose and less efficient yet is easier to read and easier to access via a traditional terminal interface Both binary and ASCII text encoding methods share an identical command structure and support the entire 3 Space command set The 3 Space Sensor buffers the incoming command stream and will only take an action once the entire packet has been received and the checksum has been verified as correct ASCII mode commands do not use checksums for convenience Incomplete packets and packets with incorrect checksums will be ignored This allows the controlling system to send command data at leisure without loss
40. ion Byte 107 0x6B Enable disable gyroscope Enable or disable gyroscope readings as inputs to he orientation estimation Note that updated readings are still accessible via commands This setting can be saved to non volatile flash memory using the Commit Settings command Mode Byte 108 0x6C Enable disable laccelerometer Enable or disable accelerometer readings as inputs o the orientation estimation Note that updated accelerometer readings are still accessible via commands This setting can be saved to non volatile flash memory using the Commit Settings command Mode Byte 26 User s Manual Command Description Long Description Return Data Len Return Data Details Data Len Data Details 109 0x6D Enable disable compass Enable or disable compass readings as inputs to the orientation estimation Note that compass readings are still accessible va commands This setting can be saved to non volatile flash memory using the Commit Settings command Mode Byte 110 0 6 Reset multi reference vectors to zero Resets all reference vectors in the multi reference table to zero Intended for advanced users 111 0x6F Set multi reference table resolution Sets the number of cell dimensions and number of nearby vectors per cell for the multi reference lookup table First parameter indicates the number of c
41. is in Multi Accelerometer reference 134 0x86 reference vector Reference Vector mode 12 vector float x4 0 Reads the current reference vector mode Retum Read reference vector value can be 0 for single static 1 for single auto 2 135 0x87 mode for single auto continuous or 3 for multi 1 Mode byte Reads the multi reference mode compass reference Read compass multi vector at the specified index Intended for advanced Compass multi reference 136 0x88 reference vector users 12 reference vector float x3 1 Index byte Reads the multi reference mode compass reference Compass multi reference Read compass multi check vector at the specified index Intended for reference check vector 137 0x89 reference check vector advanced users 12 float x3 1 Index byte Reads the multi reference mode accelerometer Accelerometer multi Read accelerometer multi reference vector at the specified index Intended for reference reference vector 138 0x8a reference vector advanced users 12 float x3 1 Index byte Reads the multi reference mode accelerometer Accelerometer multi Read accelerometer multi reference check vector at the specified index reference reference check 139 0x8b reference check vector Intended for advanced users 12 vector float x3 1 Index byte Returns a value indicating whether the gyroscope Read gyroscope enabled contribution is currently part of the orientation Gyroscope enabled value 140 0x8c state estimate O for off 1 for on 1
42. ithms to determine orientation relative to an absolute reference orientation in real time Orientation can be returned in absolute terms or relative to a designated reference orientation The proprietary multi reference vector mode increases accuracy and greatly reduces and compensates for sensor error The YEI 3 Space Sensor Data Logging system also utilizes a dynamic sensor confidence algorithm that ensures optimal accuracy and precision across a wide range of operating conditions The YEI 3 Space Sensor Data Logging unit features are accessible via a well documented open communication protocol that allows access to all available sensor data and configuration parameters using a USB 2 0 interface and configuration parameters are also accessible through configuration files on the SD card Versatile commands allow access to raw sensor data normalized sensor data and filtered absolute and relative orientation outputs in multiple formats including quaternion Euler angles pitch roll yaw rotation matrix axis angle two vector forward up The YEI 3 Space Sensor Data Logging grants access to its SD card on a host PC through a USB Mass Storage interface Settings for how to gather data can be accessed through configuration files and gathered data can be stored in a variety of formats onto the SD card The SD card uses the FAT32 filesystem When used as a USB device the 3 Space Sensor provides mouse emulation and joystick emulation modes tha
43. ithout any additional post Acceleration Vector in 66 0 42 data processing 12 counts per g Vector x3 0 Returns the raw compass vector as read directly from the compass without any additional post Compass Vector in counts 67 0x43 Read raw compass data processing 12 per gauss Vector x3 0 25 User s Manual 4 3 7 Configuration Write Commands Command Description Long Description Return Data Len Return Data Details Data Len Data Details 96 0x60 Tare with current orientation Sets the tare orientation to be the same as the current filtered orientation 0 97 0x61 Tare with quaternion Sets the tare orientation to be the same as the supplied orientation which should be passed as a quaternion 16 Quaternion float x4 98 0x62 Tare with rotation matrix Sets the tare orientation to be the same as the supplied orientation which should be passed as a rotation matrix 36 Rotation Matrix float x9 99 0x63 Set static accelerometer rho mode Determines how trusted the accelerometer contribution is to the overall orientation estimation Higher values mean that the accelerometer is less trusted Accelerometer rho value float 100 0x64 Set confidence laccelerometer rho mode Determines how trusted the accelerometer contribution is to the overall orientation estimation Instead of using a single value uses a
44. ive Y Second resulting component Bit 6 Positive Negative X First resulting component Axis Direction Byte byte 27 User s Manual Command Description Long Description Return Data Len Return Data Details Data Len Data Details 117 0x75 Set running average percent Sets what percentage of running average to use on the sensor s orientation This is computed as follows total orient total orient percent current orient total orient total orient percent total orient current orient 1 If the percentage is 0 the running average will be shut off completely Maximum value is 9796 This setting can be saved to non volatile flash memory using the Commit Settings command Running Average Percent float 118 0x76 Set compass reference vector Sets the static compass reference vector for Single Reference Mode 12 Compass Reference Vector float x3 119 0x77 Set accelerometer reference vector Sets the static accelerometer reference vector for Single Reference Mode 12 Accelerometer Reference Vector float x3 120 0x7c Reset Kalman filter Resets Kalman filter s state and covariance matrices 121 0x79 Set accelerometer range Only parameter is the new accelerometer range which can be 0 for 2g Default range which can be 1 for 4g or 2 for 89 Higher ranges can detect and report larger acceleratio
45. lerometer and compass are unit length vectors Gyro Rate Vector x3 indicating the direction of gravity and north Gravity Direction Vector Read all normalized respectively These two vectors do not have any x3 North Direction Vector 32 0x20 component sensor data magnitude data associated with them 36 x3 0 Returns the normalized gyro rate vector which is in 33 0x21 Read normalized gyro rate units of radians sec 12 Gyro Rate Vector x3 0 Returns the normalized accelerometer vector Note that this is a unit vector indicating the direction of Read normalized gravity This vector does not have any magnitude Gravity Direction Vector 34 0x22 accelerometer vector data associated with it 12 x3 0 Returns the normalized compass vector Note that this is a unit vector indicating the direction of gravity Read normalized compass This vector does not have any magnitude data 35 0x23 vector associated with it 12 North Direction Vector x3 0 4 3 3 Other Data Commands Return Data Command Description Long Description Data Len Return Data Details Len Data Details 36 0x24 Read temperature C Returns the temperature of the sensor in Celsius 4 Temperature float 0 37 0x25 Read temperature F Returns the temperature of the sensor in Fahrenheit 4 Temperature float 0 Returns a value indicating how much the sensor is being moved at the moment This value will return 1 ifl the sensor is completely stationary and will return 0 if it is in motion This c
46. matting utility such as the one built in to Windows format the card as a single FAT32 partition or insert the unformatted card into the Data Logging 3 Space Sensor and call command 59 look in section 4 for details on this command Also the 3 Space Suite has an easy way to call this command in the Sensor Info window when connected to a Data Logging sensor Refer to the Data Logging Quick Start guide for more information When the card has been properly initialized by the sensor the LED will turn solid blue The directory structure the sensor sets up is as follows Root Directory Data Config The Data directory is for holding the results of any data capture sessions A new directory inside this will be created for each session named according to when the capture started For information on setting up the current time see section 3 4 4 This Config directory holds configuration files which can be modified to change the current settings of the sensor It contains two files sensor cfg and capture cfg sensor cfg allows access to many sensor settings that can also be modified through protocol commands such as orientation averaging modes capture cfg allows access to settings having to do with how and how often data is gathered See section 3 4 3 for information on the contents of capture cfg and data logging options in general In order to change a setting in one of these files simply find the name of the property you want to modify on t
47. minimum and maximum value Rho values will be changed within this range depending on the confidence factor This can have the effect of smoothing out the laccelerometer when the sensor is in motion Minimum accelerometer rho value float Maximum laccelerometer rho value float 101 0x65 Set static compass rho mode Determines how trusted the accelerometer contribution is to the overall orientation estimation Higher values mean that the compass is less trusted Compass rho value float 102 0x66 Set confidence compass rho mode Determines how trusted the compass contribution is to the overall orientation estimation Instead of using a single value uses a minimum and maximum value Rho values will be changed within this range depending on the confidence factor This can have the effect of reducing the compass s effect on the overall orientation estimation and thus reducing magnetically induced interference Minimum compass rho value float Maximum compass rho value float 103 0x67 Set desired update rate Causes the processor to wait for the specified number of microseconds at the end of each update loop Can be useful for bounding the overall update rate of the sensor if necessary Microsecond update rate unsigned integer 104 0x68 Set multi reference vectors with current orientation Uses the current tared orientation to set up the reference vector for the nearest orthogonal
48. mmand Value Selected from the command chart in decimal Start of ASCII Packet Indicated by the colon character Figure 2 Typical ASCII Command Packet Format Thus the ASCII packet consists of the the following characters the ASCII colon character signifies the start of an ASCII text packet the ASCII comma character acts as a value delimiter when multiple values are specified the ASCII period character is used in floating point numbers 0 9 the ASCII digits are used to in integer and floating point values the ASCII minus sign is used to indicate a negative number n the ASCII newline character is used to signify the end of an ASCII command packet b the ASCII backspace character can be used to backup through the partially completed line to correct errors If a command is given in ASCII mode but does not have the right number of parameters the entire command will be ignored Sample ASCII commands 0 n Read orientation as a quaternion 106 2 n Set oversample rate to 2 ASCII Return Values All values are returned in ASCII text format when an ASCII format command is issued To read the return data simply read data from the sensor until a Windows newline a carriage return and a line feed is encountered 22 User s Manual 4 3 Command Overview There are over 90 different command messages that are grouped numerically by functi
49. n estimate Please note that these only affect the final orientation and not the readings of individual component sensors Oversampling Oversampling causes the sensor to take extra readings from each of the component sensors and average them before using them to estimate orientation This can reduce noise but also causes each cycle to take longer proportional to how many extra samples are being taken Running Average The final orientation estimate can be put through a running average which will make the estimate smoother at the cost of introducing a small delay between physical motion and the sensor s estimation of that motion e Rho Values As mentioned earlier by default the accelerometer and compass are trusted less than the gyros when the sensor is in motion Rho values are the mechanism that handles the concept of trust They involve parameters one for the accelerometer and one for the compass that indicate how much these component sensors are to be trusted relative to the gyroscope A lower value for the parameter means more trust The default mode for this is confidence mode where the rho value chooses between a minimum and maximum value based on how much the sensor is moving The other option is to have a single static rho value 12 User s Manual 3 2 Communication Obtaining data about orientation from the sensor or giving values for any of its settings is done through the sensor s communication protocol T
50. natural axes are illustrated in the diagram below Bear in mind the difference between natural axes and the axes that are used in protocol data While they are by default the same they can be remapped so that for example data axis Y could contain data from natural axis X This allows users to work with data in a reference frame they are familiar with User s Manual 3 Description of the 3 Space Sensor 3 1 Orientation Estimation The primary purpose of the 3 Space Sensor is to estimate orientation In order to understand how to handle this estimation and use it in a meaningful way there are a few concepts about the sensor that should be understood The following sections describe these concepts 3 1 1 Component Sensors The 3 Space Sensor estimates orientation by combining the data it gets from three types of sensors a gyroscope an accelerometer and a compass A few things you should know about each of these sensors Accelerometer This sensor measures the acceleration due to gravity as well as any other accelerations that occur Because of this this sensor is at its best when the 3 Space Sensor is sitting still Most jitter seen as the orientation of the sensor changes is due to shaking causing perturbations in the accelerometer readings To account for this by default when the 3 Space Sensor is being moved the gyroscope becomes more trusted becomes a greater part of the orientation estimate and the accelerometer b
51. ns but are not as accurate for smaller accelerations This setting can be saved to non volatile flash memory using the Commit Settings command Accelerometer range setting byte 122 0x7a Set multi reference weight power Set weighting power for multi reference vector weights Multi reference vector weights are all raised to the weight power before they are summed and used in the calculation for the final reference vector Setting this value nearer to 0 will cause the reference vectors to overlap more and setting it nearer to infinity will cause the reference vectors to influence a smaller set of orientations Weight power float 123 0x7b Set filter mode Used to disable the orientation filter or set the orientation filter mode Changing this parameter can be useful for tuning filter performance versus orientation update rates Passing in a parameter of 0 places the sensor into IMU mode a 1 places the sensor into Kalman Filtered Mode Default mode a 2 places the sensor into Alternating Kalman Filter Mode and a 3 places the sensor into Complementary Filter Mode More information can be found in Section 3 1 5 This setting can be saved to non volatile flash memory using the Commit Settings command Mode Byte 124 0x7c Set running average mode Used to further smooth out the orientation at the cost of higher latency Passing in a parameter of 0 places the sensor into a static running average mode
52. of functionality The command buffer will however be cleared whenever the 3 Space Sensor is either reset or powered off on Specific details of the 3 Space Sensor protocol and its control commands are discussed in the following pages 4 1 2 Computer Interfacing Overview The Data logging 3 Space Sensor enumerates as a composite USB device consisting of a USB mass storage device a CDC serial communication device and an HID mouse keyboard device When interfacing with a computer the 3 Space Sensor presents itself as a COM port which provides an interface by which the serial communication the protocol requires may happen The name of this COM port is specific to the operating system being used It is possible to use multiple 3 Space Sensors on a single computer Each will be assigned its own COM port The USB mass storage device allows access the configuration files that are used to determine sensor configuration and data logging options For more detail on these files refer to section 3 4 Data Logging For more information on how to install the sensor software on a computer and begin using it see the Quick Start guide 20 User s Manual 4 2 Protocol Packet Format 4 2 1 Binary Packet Format The binary packet size can be three or more bytes long depending upon the nature of the command being sent to the controller Each packet consists of an initial start of packet byte followed by a command value specifier by
53. ommand can also return values in between indicating how much motion the 38 0x26 Read confidence factor sensor is experiencing 4 Confidence Factor float 0 4 3 4 Corrected Data Commands Return Data Command Description Long Description Data Len Return Data Details Len Data Details Returns the acceleration vector in units of G Note Read corrected that this acceleration will include the static Acceleration Vector in units 39 0x27 accelerometer component of acceleration due to gravity 12 of G float x3 0 Compass Vector in units of 40 0x28 Read corrected compass Returns the compass vector in units of gauss 12 gauss float x3 0 24 User s Manual 4 3 5 Data Logging Commands Return Data Command Description Long Description Data Len Return Data Details Len Data Details Causes the sensor to enumerate as a mass storage device When the sensor is in this mode SD card data can be read However data cannot be logged Turn on mass storage This mode will be enabled automatically when the 57 0x39 mode sensor is plugged in 0 0 Causes the sensor to stop enumerating as a mass storage device When the sensor is in this mode data can be logged However data cannot be Turn off mass storage accessed This mode will be enabled automatically 58 0x3A mode when the sensor is unplugged 0 0 Format and Initialize SD 59 0x3B Card Erases the content
54. on Unused command message bytes are reserved for future expansion When looking at the following command message tables note the following The Data Len field indicates the number of additional data bytes the command expects to follow the command byte itself This number doesn t include the Start of Packet Command or Checksum bytes Thus the total message size can be calculated by adding three bytes to the Data Len listed in the table Likewise the Return Data Len field indicates the number of data bytes the command delivers back to the sender once the command has finished executing Under Return Data Details each command lists the sort of data which is being returned and next to this in parenthesis the form this data takes For example a quaternion is represented by 4 floating point numbers so a command which returns a quaternion would list Quaternion float x4 for its return data details Command length information only applies to binary commands as ascii commands can vary in length For quaternions data is always returned in x y z w order Euler angles are always returned in pitch yaw roll order When calling commands in ASCII mode there is no fixed byte length for the parameter data or return data as the length depends on the ASCII encoding 4 3 1 Orientation Commands Return Data Command Description Long Description Data Len Return Data
55. or 60 Mhz default This setting does not need to be committed but does not take effect until the sensor is reset Clock speed in Hz int 236 0 clock speed Returns the current processor clock speed Clock speed in Hz int 237 0xed Get serial number Returns the serial number which will match the value etched onto the physical sensor Serial number int 238 0 LED color Sets the color of the LED on the sensor to the specified RGB color This setting can be committed to non volatile flash memory by calling the Commit Wireless Settings command 12 RGB Color float x3 239 0 Get LED color Returns the color of the LED on the sensor 12 RGB Color float x3 32 User s Manual 4 3 12 Wired HID Commands Command Description Long Description Return Data Len Return Data Details Data Len Data Details 240 0xf0 Enable disable joystick Enable or disable streaming of joystick HID data for this sensor 0 Joystick enabled state byte 241 0xf1 Enable disable mouse Enable or disable streaming of mouse HID data for this sensor Mouse enabled state byte 242 0xf2 Read joystick enabled Read whether the sensor is currently streaming joystick HID data Joystick enabled state byte 243 0xf3 Read mouse enabled Read whether the sensor i
56. rol s mode The control classes and indices are the same as described in command 244 Handler index byte Control class byte control index byte 247 0xf7 Read control data Reads the value of a certain parameter of the specified control s operation mode The control classes and indices are the same as described in command 244 Data point float Control class byte control index byte data point index byte 248 0xf8 Set button gyro disable length Determines how long in frames the gyros should be disabled after one of the physical buttons on the sensor is pressed A setting of 0 means they won t be disabled at all This setting helps to alleviate gyro disturbances cause by the buttons causing small shockwaves in the sensor Number of frames byte 249 0xf9 Get button gyro disable lentgh Returns the current button gyro disable length 1 Number of frames byte 250 0xfa Read button state Reads the current state of the sensor s physical buttons This value returns a byte where each bit represents the state of the sensor s physical buttons Button state byte 251 0xfb Set mouse absolute relative mode Puts the mode in absolute or relative mode This change will not take effect immediately and the sensor must be reset before the mouse will enter this mode The only parameter can be 0 for absolute default or 1 for relative Absolute or relative mode
57. s transmitted as a single 8 bit byte value 21 User s Manual 4 2 2 ASCII Text Packet Format ASCII text command packets are similar to binary command packets but are received as a single formatted line of text Each text line consists of the following an ASCII colon character followed by an integral command id in decimal followed by a list of ASCII encoded floating point command values followed by a terminating newline character The command id and command values are given in decimal The ASCII encoded command values must be separated by an ASCII comma character or an ASCII space character Thus legal command characters are the colon the comma the period the digits 0 through 9 the minus sign the new line the space and the backspace When a command calls for an integer or byte sized parameter the floating point number given for that parameter will be interpreted as being the appropriate data type For simplicity the ASCII encoded commands follow the same format as the binary encoded commands but ASCII text encodings of values are used rather than raw binary encodings Each ASCII packet is formatted as shown in figure 2 Ra a 1 aco Wa Conmand End of Packet The ASCII newline character Command Data Zero or more bytes representing parameters to the command being called See the command chart for details Co
58. s currently streaming mouse HID data Mouse enabled state byte 4 3 13 General HID Commands Command Description Long Description Return Data Len Return Data Details Data Len Data Details 244 0xf4 Set control mode Sets the operation mode for one of the controls The first parameter is the control class which can be 0 for Joystick Axis 1 for Joystick Button 2 for Mouse Axis or 3 for Mouse Button There are two axes and eight buttons on the joystick and mouse The second parameter the control index selects which one of these axes or buttons you would like to modify The third parameter the handler index specifies which handler you want to take care of this control These can be the following Turn off this control 255 Axes Global Axis 0 Screen Point 1 Buttons Hardware Button 0 Orientation Button 1 Shake Button 2 Control class byte control index byte handler index byte 245 0xf5 Set control data Sets parameters for the specified control s operation mode The control classes and indices are the same as described in command 244 Each mode can have up to 10 data points associated with it How many should be set and what they should be set to is entirely based on which mode is being used 0 Control class byte control index byte data point index byte data point float 246 0xf6 Read control mode Reads the handler index of this cont
59. s of the SD card 0 0 Initiates a data logging section with the specified attributes as indicated in the provided data logging 60 0 3 Begin data logging session configuration file 0 0 61 0x3D End data logging session Terminates the ongoing data logging session 0 0 Month Byte Day Byte Year Byte Hour Byte 62 0x3E Set clock values Sets the current time on the onboard real time clock 6 Minute Byte Second Byte Month Byte Day Byte Year Byte Hour Byte Returns the current time as read by the onboard Minute Byte Second 63 0x3F Read clock values real time clock 6 Byte 0 4 3 6 Raw Data Commands Return Data Command Description Long Description Data Len Return Data Details Len pata Details Gyro Rate in counts per Returns the raw gyro rate vector accelerometer degrees sec Vector x3 vector and compass vector as read directly from the Acceleration Vector in component sensors without any additional post counts per g Vector x3 Read all raw component processing The range of values is dependent on the Compass Vector in counts 64 0 40 sensor data currently selected range for each respective sensor 36 per gauss Vector x3 0 Returns the raw gyro rate vector as read directly from the gyroscope without any additional post Gyro Rate in counts per 65 0 41 Read raw gyroscope rate processing 12 degrees sec Vector x3 0 Returns the raw acceleration vector as read directly Read raw accelerometer from the accelerometer w
60. ss to raw sensor data MicroSD card allows for data logging applications USB allows for real time applications MicroSD card uses standard FAT32 file system Flexible data logging configuration allows customization of logged data and allows event based and time based logging options Built in clock calendar provides for fully time stamped event logging at high resolution USB communication through a virtual COM port Enumeration as USB mass storage device makes access to logged data easy USB joystick mouse emulation modes ease integration with existing applications Upgradeable firmware RGB status LED two programmable input buttons Available in either hand held or strap down packaging RoHS compliant User s Manual 2 5 Block Diagram of Sensor Operation USB 2 0 Host System TSS Data logging MicroSD Card LiPo Battery amp Real time Clock Slot Charge Management amp Calendar Processor 7 USB 2 0 MircoSD Card Interface Media Interface Esc rna y Orientation Emulation Non volatile Calibration amp Kalman id Filter es Scale Bias Normalization amp Error Compensation 3 Axis 3 Axis 3 Axis Temperature Accelerometer Rate Gyro Compass Sensor User s Manual 2 6 Specifications General Part number TSS DL Handheld Sensor Unit TSS DL S Strapdown Sensor Unit TSS DL HH High range Handheld Sensor Unit TSS DL HH S High rang
61. t e d e RE re HER Een dei IERI 24 4 3 3 Other Data Comimands Reece UN ee e Re et a 24 43 4 Corrected Data Commands eee etit t eod Qe nee aa eh 24 4 3 5 Data Logging Commands enne enne nenne rs nter e nre t nennen 25 43 6 Raw Data Commands nei ene e aei tages e e e ee eed Cep 25 4 3 7 Configuration Write Commands vete E ea eR RORIS 26 4 3 8 Configuration Read Commands 29 4 3 9 Calibration Commands A a enne nr eene ner innen ern inen nennen nnne nns 31 43 10 Battery Commands oi eedem e HT HR UTR ER E PE E ee eU end 32 4 3 1 T General eee ER S VA e PRISE DIR ES 32 43 12 Wired Commands e RE ERE RENE A et 33 4 3 13 General HID 5 000 2000 0 0 0 000000000000 33 User s Manual AppendiX A a a EN USB Connector Decimal Conversion Chart uy s n ette te ettet u u e lente eon ee E OEA User s Manual 1 Usage Safety Considerations 1 1 Usage Conditions Do not use the 3 Space Sensor in any system on which people s lives depend life support weapons etc Because of its reliance on a compass the 3 Space Sensor will not work properly near the earth s north or south pole Because of its reliance on a compass and accelerometer th
62. t ease integration with existing applications 2 2 Applications Robotics performance analysis Motion capture nformation gathering Personnel pedestrian tracking Unmanned air land water vehicle tracking Education and performing arts Healthcare monitoring Asset tracking Vibration analysis and monitoring Event detection and monitoring User s Manual 2 3 Hardware Overview 1 USB Connector The 3 Space Sensor uses a 5 pin mini USB connector to connect to a computer via USB and to charge the internal battery The USB connector provides for both power and communication signals 2 Recessed Power Switch The 3 Space Sensor can be switch on and off when powered from the internal battery by using the recessed power switch When connected via USB the unit is powered and the batteries will begin recharging regardless of the position of the recessed power switch 3 Input Button 1 The 3 Space Sensor includes two input buttons that can be used in conjunction with the orientation sensing capabilities of the device The inputs are especially useful when using the 3 Space Sensor as an input device such as in joystick emulation mode or mouse emulation mode 4 Indicator LED The 3 Space Sensor includes an RGB LED that can be used for visual status feedback 5 Input Button 2 The 3 Space Sensor includes two input buttons that can be used in conjunction with the orientation sensing capabilities of the de
63. te followed by zero or more command data bytes and terminated by a packet checksum value byte Each binary packet 1s at least 3 bytes in length and is formatted as shown in figure 1 247 0 7 6 222 First Byte Start of Packet Second Byte Command Value Selected from the command chart Command 4 Command Data Command Data Zero or more bytes representing parameters to the command being called See the command chart for details Command Data Last Byte Packet Checksum Checksum Sum of all other bytes except the first Figure 1 Typical Binary Command Packet Format Binary Return Values When a 3 Space Sensor command is called in binary mode any data it returns will also be in binary format For example if a floating point number is returned it will be returned as its 4 byte binary representation For information on the floating point format go here http en wikipedia org wiki Single precision floating point format Also keep in mind that integer and floating point values coming from the sensor are stored in big endian format The Checksum Value The checksum is computed as an arithmetic summation of all of the characters in the packet except the checksum value itself modulus 256 This gives a resulting checksum in the range 0 to 255 The checksum for binary packets i
64. tion please 152 0x98 Read filter mode refer to the Set Filter Mode command 123 1 Filter mode byte 0 Read running average Reads the selected mode for the running average Running average mode 153 0x99 mode which can be 0 for normal or 1 for confidence 1 byte 0 Reads the current gyroscope measurement range which be 0 for 250 DPS 1 for 500 DPS or 2 Gyroscope range setting 154 0x9a Read gyroscope range for 2000 DPS 1 byte 0 Reads the current compass measurement range which can be 0 for 0 88G 1 for 1 3G 2 for 1 9G for 2 5G 4 for 4 0G 5 for 4 7G 6 for 5 6G or Compass range setting 155 0x9b Read compass range 7 for 8 1G 1 byte 0 30 User s Manual 4 3 9 Calibration Commands Command Description Long Description Return Data Len Return Data Details Data Len Data Details 160 0xa0 Set compass calibration coefficients Sets the current compass calibration parameters to the specified values These consist of a bias which is added to the raw data vector and a matrix by which the value is multiplied This setting can be saved to non volatile flash memory using the Commit Settings command 48 Bias float x3 Matrix float x9 161 0xa1 Set accelerometer calibration coefficients Sets the current accelerometer calibration parameters to the specified values These consist of a bias which is added to the raw data vector and a matrix by which th
65. tion matrix form g The current calculated angular difference between readings in quaternion form uq The untared orientation in quaternion form ua The untared orientation in axis angle form ue The untared orientation in Euler angle form given in pitch yaw roll order um The untared orientation in rotation matrix form ng The latest normalized scaled and biased gyroscope reading na The latest normalized scaled and biased accelerometer reading nc The latest normalized scaled and biased compass reading nt The latest temperature reading in degrees C nb The battery level percentage rg The raw as it comes from the sensor gyroscope reading ra The raw as it comes from the sensor accelerometer reading rc The raw as it comes from the sensor compass reading An actual 96 Note that any non data characters will only be included in the file in ASCII data logging mode For more information see the property CaptureDataMode In ASCII mode data that is comprised of multiple values will be separated by commas 15 User s Manual CaptureRate The CaptureRate property in the capture cfg file determines the desired sampling period while logging is active This property is specified in milliseconds CaptureStyle The CaptureStyle property in the capture cfg file determines if continuous or periodic data capture style is used In continuous mode data logging will be enabled at all tim
66. tional Calibration This setting can be saved to non volatile flash memory using the Commit Settings command Mode Byte 170 0xaa Read calibration mode Reads the current calibration mode which can be 0 for Bias 1 for Scale Bias or 2 for Ortho Calibration For more information refer to section 3 1 3 Additional Calibration Mode byte 171 0xab Set ortho calibration data point from current orientation Set the ortho calibration compass and accelerometer vectors corresponding to this orthogonal orientation Intended for advanced users 172 0xac Set ortho calibration data point from vector Directly set a vector corresponding to this orthogonal orientation First parameter is type where 0 is for compass and 1 is for accelerometer Second parameter is index which indicates the orthogonal orientation Intended for advanced users 14 Type Byte Index Byte Accelerometer or Compass Vector float x3 173 0xad Read ortho calibration data point Return the vector corresponding to the orthogonal orientation given by index First parameter is type where 0 is for compass and 1 is for accelerometer Second parameter is index which indicates the orthogonal orientation Intended for advanced users 12 Accelerometer or compass vector float x3 Type Byte Index Byte 174 0xae Perform ortho calibration Stores accelerometer and compass data in the ortho lookup table for us
67. ttery low battery life remaining is at or below 5 Yellow Single Pulse when plugged into USB Battery is actively charging Green Single Pulse when plugged into USB Battery is fully charged Red Rapid Constant Pulse Panic mode Indicates corrupted sensor settings 3 4 5 Real Time Clock The Data Logging 3 Space Sensor contains a real time clock chip which allows it to keep track of time The clock chip uses a separate clock battery which maintains the time and clock settings This internal clock battery is calculated to have a life of about 5 years The clock chip must be given an initial time for it to report time properly in a desired time zone This time can be given to the chip using command 62 and read back using command 63 See the entries for these commands in Section 4 for more details In addition the 3 Space Suite has an option for automatically setting the clock of the sensor to the clock of the host computer Go to the Sensor Info window when connected to the Data Logging sensor and there will be an option to do this For more information refer to the Data Logging Quick Start Guide 17 User s Manual 3 5 Sensor Settings 3 5 1 Committing Settings Changes made to the 3 Space Sensor will not be saved unless they are committed This allows you to make changes to the sensor and easily revert it to its previous state by resetting the chip For instructions on how to commit your changes see the Quick Start
68. vice The inputs are especially useful when using the 3 Space Sensor as an input device such as in joystick emulation mode or mouse emulation mode 6 Recessed MicroSD Card Slot The 3 Space Sensor MicroSD media can be inserted or removed through the recessed slot This slot is recessed to help prevent accidental card removal User s Manual 2 4 Features The YEI 3 Space Sensor Data Logging has many features that allow it to be a flexible all in one solution for your orientation sensing needs Below are some of the key features Small self contained high performance data logging AHRS at 35mm x 60mm x 15mm and 28 grams Integrated Lithium Polymer battery and charge control allows battery life of 5 hours at full performance Fast sensor update and filter rate allow use in highly dynamic applications including motion capture performance amp motion analysis and navigation Highly customizable orientation sensing with options such as tunable filtering oversampling and orientation error correction Advanced integrated Kalman filtering allows sensor to automatically reduce the effects of sensor noise and sensor error Robust open protocol allows commands to be sent in human readable form or more quickly in machine readable form Orientation output format available in absolute or relative terms in multiple formats quaternion rotation matrix axis angle two vector Absolute or custom reference axes Acce
69. vice x es m e ette oie ID pe Nes 13 3 4 2 SD Card Format and Directory Structure n enne 14 3 43 Data Logping isa aues ee ORO RR QW bett eR e er dvi ee RG 14 3 44 LED Capture Behayilot Se dee d T ER Or me t Toes eee 17 3 45 Real Ime Clock eine aged otc ee aid ida EDI 17 3 5 Sensor Settings Re eH REOR RT ERR GU EGRE EE RC HR e e y 18 3 531 Commut ng Settthigs s voee ERU m Ree 18 3 52 Natural AX CSc 5 ceri das qe eit viec Uu RU dave E S 18 3 5 3 Sensor Settings and Defaults rir RR ERE C 18 3 5 4 Capture Settings and Defaults eene enne enne nete nnne nnne nnne nennen nns 19 4 3 Space Sensor Usage Protocol 5 eint eet tete ein e aree ite a ie RE 20 4 1 Usage Overview en ris d I tede a Nee ues 20 4 11 Protocol OVervIew e ettet RPG E Re e 20 4 1 2 Computer Interfacing Overview eene nnne nnne trennen nnn enne enne nnne nens 20 4 2 Protocol Packet uto e C e s EAR E e Gia te eet ago 21 42 3 Binary Packet PForm t tereti ee ids 21 4 22 ASCH Text Packet eto ttr E s a se et be erre ele e e ted 22 4 3 Command Overviews i era eae ern ege diee n PM aO nri 23 43 1 Orientation Command nT a pee e Rer e e RR E EH e ege de 23 4 3 2 Normalized Data Commands inesse

3-Space Sensor Data-Logging User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents