L7000 Home Automation Quick Guide
Contents
1. Honeywell LYNX TOUCH SECURITY SYSTEM Quick Guide to Home Automation Functions Full Home Automation Guide Available Online This Quick Guide describes the most frequently used features and functions of your system For full details of all functions please see the system s Home Automation located online at http www security honeywell com hsc products see LYNX Touch Security System Home Automation Guide P N 800 16091 or higher The full version Home Automation Guide is also available from your installer upon request General Information The Honeywell LYNX Touch control is a security enabled Z Wave device that is designed to automate devices in a home control network The control allows you to easily add and control multiple devices with the press of a button and supports Z Wave Network Wide Inclusion NWI mode Management of Z Wave devices which are also known as nodes or modules includes two main operations inclusion exclusion and control This section describes how to Include add devices into your home control network edit devices and Exclude delete devices Automation and Z Wave functions are accessed via the LYNX Touch Automation icon Z Wave Device Management and Z Wave Advanced Tools screens The devices can be controlled from the LYNX Touch control or a Mobile Device Once the Z Wave devices have been Included added to the network they can be controlled either manually or through Scenes that are programmed using you2. to return to the Home screen or key to return to the Home screen or select the S button Note The features and functions that can be controlled vary by to return to the previous screen manufacturer Refer to the User Manual that was provided with the Z Wave device to determine the specific capabilities Manually Activating Z Wave Devices Continued T Ready To Arm Den Lamp 9 Press to Turn Off Living Room 34 mode HEAT i SS Fan AUTO 5200 100 101 VO Thermostat Control Screen Ready To Arm Den Lamp ON 70 9 lay to Turn Off L JUUUUUUU Weel J 5200 100 100 VO Dimmer Switch Control Screen Ready To Arm Set to 25 5C 23 0 Living Room v a Mode HEAT SE Fan 5200 100 103 VO Thermostat Energy Savings Control Screen Ready To Arm Unknown 001 Secured Unknown Type 0000 ID 0000 Node 2 Sigma Designs Sigma Designs Basic Off Basic On OFF 5200 100 104 VO Unsupported Device Control Screen T Ready To Arm aR 68 Setpoint m Saponi kan iving Room 738 Vv 34K mode AUTO SE Fan AUTO 5200 100 102 VO Thermostat Dual Setback Control Screen Ready To Arm gt Ready To Arm Ready To Arm Press to Lock Switch 003 lt ee i i Press to open la Press to Turn Off M Water On rN Front Door Unlocked Garage Door 1 CLOSED Close in Close at 5200 100 098 VO Lock Control Screen Water Valve Co
3. to the Rules Screen Water Valves Provides access to the Water Valves Screen Provides access to the Z Wave Device Management Screen Provides access to control Garage Door ANEC Garage door Provides access to program enroll m waledes operation setup Garage Door Openers Displayed if a device failure is detected in the Z Wave network For additional Press To See information Refer to the Failed Device Failed devices section of LYNX Touch Security System Home Automation Guide P N 800 16091 or higher Provides access to control Unknown or Other Devices Unsupported Devices using basic On Off commands wave Wave and Z Wave Plus are registered trademarks of Sigma Designs and its subsidiaries in the United States and other countries Z Wave System Basics Continued Editing Z Wave Device Names The steps described below should be accomplished at the LYNX Z Wave Device Management Screen Options Touch control in order to edit a Z Wave devices name Include Devices Enroll Z Wave Devices Modules Action At the Home Screen select the Automation icon Exclude Devices Delete Z Wave Devices Modules At the Automation Screen select the type of device to edit Displayed only when device failures have been detected in the Z Wave network For additional information Refer to the Failed Device section of LYNX Touch Security System Home Automation Guide P N 800 16091 or higher Provides access to additional Z Wave Advanced Tool
4. duled Function section to edit and save your changes Select the Delete button At the displayed confirmation screen select Yes to confirm the deletion Select the S button or press the Home key to return to the Automation programming or the Home screen Programming Editing Deleting Rules The steps described below should be accomplished at the LYNX Touch control in order to program up to 20 Rules that are used for Triggers Z Wave Scenes and Follow Me Messages For more detailed information regarding Rules refer to the full Home Automation Guide P N 800 16091 or higher Program a Rule Select the Automation icon from the Home Screen 4 Select the Rules icon from the second page of the Automation screen The Rules screen is displayed At the Rules screen select a Rules key Select Name then enter a name limited to 13 characters for the Rule on the displayed keypad then select Done 800 16092 12 13 Rev B Select the S button or press the Home key to return to the Automation programming or the Home screen a At the Schedules screen select the Schedule to edit or delete Programming Editing Deleting Rules Continued Step 14 Edit or Step 3 Garage Door Feature Operation step 3 Edit Close in Close at Back Press to open Press to close Select the Type button to toggle through the type op
5. er Program a Scheduled Function Select the Automation icon from the Home Screen Select the Schedules icon from the second page of the Automation screen The Schedules screen is displayed At the Schedules screen select Add New Select Name then enter a name limited to 13 characters for the schedule on the displayed keypad 4 then select Done D Select Frequency then select one of the displayed options Program the options based upon the Frequency selected in Step 5 7 Select Type to scroll between the available options If Auto Stay is selected select Start Time and proceed to Step 9 If Rules is selected proceed to Step 10 If Disarm Notification is selected proceed to Step 11 On the displayed keypad select Clear and enter a 4 digit time on the displayed keypad then select Save Select Rules OR Scenes as applicable then select a Rule or Scene from the displayed list Select Start Time and End Time and on the displayed keypad select Clear Enter a 4 digit Start Time and End Time as applicable then select Save 10 12 Edit or Delete a Scheduled Function Select the Edit or Delete button as applicable If editing the schedule proceed to Step 3 or if deleting proceed to Step 4 When the Schedule programming screen appears follow Steps 4 11 as noted above in the Program a Sche
6. evices Off Allows User to manually turn Off OR On all OR switches that are programmed in the Z All Devices On Wave Network cP At the Device Management screen select Exclude Devices Entering Exclusion Mode Please Wait is displayed followed by Ready to Exclude device Press the function button on the device Within one minute press the device s Function button or activate the switch If the device has been successfully excluded the device information is shown on the excluded list If a device which is not known to the panel is excluded Unknown Device Excluded is displayed on the excluded list Locking Door Once you have finished excluding devices press the Home key to return to the Home screen or select the o button to return to the previous screen Learn Controlling Z Wave Devices Z Wave devices can be activated Manually or by using Scenes to control a single or group of devices by turning them OFF ON R A ON to a preset lighting level temperature or mode and or to Including Z Wave Devices lock unlock a door The LYNX Touch provides 20 Scenes that The steps described below should be accomplished at the LYNX can be configured to control up to 10 devices each Scenes can Touch control in order to include add Z Wave devices to the be activated manually or by a Schedule or Rule Schedules and network For additional information regarding the inclusion of Rules are u
7. ntrol Screen Garage Door Control Screen Programming Editing Deleting Scenes The steps described below should be accomplished at the LYNX Touch control in order to program Scenes used to control Z Wave devices For more detailed information regarding Scenes refer to the full Home Automation Guide P N 800 16091 or higher Program a Scene Edit or Delete a Scene Ls Select the Automation icon from the Home Screen 1 Select the Automation icon from the Home Screen Select the Scenes icon from the second page of the Select the Scenes icon from the second page of the Automation screen The Scenes screen is displayed Automation screen The Scenes screen is displayed Select the scene you wish to edit or delete Select Add New Scene The system displays a keypad 3 Select the Edit or Delete button along with the next available Scene number D If Edit was selected the system advances to the Scene Edit as required and proceed to Step 6 If delete was selected proceed to Step 7 If desired select clear then enter a name limited to 13 characters for the scene on the displayed keypad then Select Save when complete The system returns to the Z Wave device screen Select the 5 button as required select Done Select the Add New Device button The system displays to return to the Automation programming screen or the Home key to return to the Home screen
8. r LYNX Touch control s Automation features Check with your Installer to see which features are available with your system N Automation is intended for lifestyle convenience It should not be used for life safety or property protection UL Z Wave automation functionality is supplementary only and has not been evaluated by UL N The Automation icon on the LYNX Touch Home Screen provides access to Z Wave Home Automation features For IQA additional information regarding terms and functions refer to the Z Wave Glossary included in LYNX Touch Security Q System Home Automation Guide P N 800 16091 or higher A list of compatible Z Wave Devices can be found in the Automation LYNX Touch Security System Home Automation Guide P N 800 16091 or higher Z Wave System Basics LYNX Touch Z Wave options are displayed on two Automation Screens The down W and up A arrows are used to scroll between the two screens Advance tools functions are displayed on the Z Wave Device Management Screen Refer to the full Home Automation Guide P N 800 16091 for complete information Automation Screen Page 1 Options Automation Screen Page 2 Options Switches Provides access to the Switches Screen Scenes Provides access to the Scenes Screen Up to 20 scenes can be programmed Thermostats Provides access to the Thermostats Screen Schedules Provides access to the Schedules Screen Locks Provides access to the Locks Screen FZ lt m Rules Provides access
9. s options Select the device that you wish to edit from the list Select the edit button Enter the desired information limited to 14 characters on the displayed keypad and then select Done The system returns to the previous screen View Failed Devices Press the Home key to return to the Home screen or select the 5 button to return to the Automation screen Z Wave Advanced Tools Excluding Z Wave Devices The steps described below should be accomplished at the LYNX Z Wave Advanced Tools Options Touch control in order to Exclude remove a Z Wave device from the network View Enrolled Devices View Z Wave device information View Enrolled View Controller Information Controllers At the Home Screen select the Automation icon At the Automation Screen select Tools Deletes all nodes and generates a new Reset Controller random Home ID Resetting the Controller does not Exclude the individual devices Transfers the role of primary controller to Pri Controller Shift another controller i e a Z Wave remote to Secondary control and duplicates the Z Wave network Enable Arm Stay Arm Away or Arm without Auto Stay when Z Wave door lock is locked Causes the system to arm in the selected mode Away Stay or Away without Auto Stay when the Z Wave Door is Locked Includes the panel as secondary controller usually on a Z Wave remote control and duplicates the Z Wave network All D
10. sed to control Scenes via pre set Conditions and specific Z Wave Devices refer to the full Home Automation Guide Triggers Up to 20 Rules may be programmed locally in the P N 800 16091 or higher LYNX Touch An additional 20 Rules can be programmed through P etion s is OY Total Connect Service Check with your Installer to see if these features are available to you At the Home Screen select the Automation icon At the second page of the Automation Screen select Tools The steps described below should be accomplished at the LYNX At the Home Screen select the Automation icon 3 Please Wait 4 Ready to include device Press the function button on device is displayed Within one minute press the device s 2 At the Automation Screen select the type of device i e Manually Activating Z Wave Devices If the module has been successfully enrolled the panel Select the device that you wish to control from the displays Device Found Please Wait and then displays the displayed list device information 4 Refer to the figures below for typical examples of the After successfully including a device the associated features that can be controlled manually for the devices information will be added to the top of the inclusion list Press the BACK key to return to the previous screen Repeat steps 4 6 to enroll additional Z Wave devices Press the Home key
11. the Edit or Delete button as applicable If editing the rule follow Steps 4 15 as noted above in the Program a Rule section If deleting the rule proceed to Step 4 Select the 5 button or press the Home key to return to the Automation programming or the Home screen Select the Automation icon from the Home Screen At the Automation Screen select the Garages icon Select the Garage door that you wish to control program from the displayed list The control advances to the Garage Door Operation screen Refer to the table below for additional operation and programming information Used to modify description of Garage Door Used to set a specific period of time up to 12 hours anc 59 minutes before an open garage door closes automatically If programmed the time will also be displayed Used to set a specific time that an open garage doo closes automatically If programmed the time will also be displayed Used to return the control to the Garage Door list Displayed when Garage Door is Closed Select to Open Garage Door Displayed when Garage Door is Open Select to Close Garage Door Corporate Center Drive Suite 100 2 Honeywell P O Box 9040 Melville NY 11747 Copyright 2013 Honeywell International Inc www honeywell com security
12. the available Z Wave device types The system displays a confirmation screen and then returns to the previous screen Select the S button as required to return to the Automation programming screen or the Home key to return to the Home screen Manually Run a Scene Select the Automation icon from the Home Screen Select the desired device type then select the applicable device from the displayed list The device s operational screen is displayed Select Save when finished Up to 10 devices may be associated with a scene Set the desired options Select the Scenes icon from the second page of the Automation screen The Scenes screen is displayed Select the scene you wish to run Select the py uter to run the scene Select Save when complete The system returns to the Z Wave device screen Select the S button as required to return to the Automation programming screen or the Home key to return to the Home screen Select one of the following options Switches Thermostats Locks Garages Water Valves Sirens Programming Editing Deleting Schedules The steps described below should be accomplished at the LYNX Touch control in order to program Schedules that are used to automatically perform certain functions at a scheduled time day of the week or month as applicable For more detailed information regarding Schedules refer to the full Home Automation Guide P N 800 16091 or high
13. tions The available options are dependent upon what features are programmed in your control The system displays several new programming fields that are dependent upon the Type that was chosen Select Action to toggle between options which is dependent on the selection made in Step 5 Select Start Zone Type OR Zone Type Fault Select an option from the displayed list which is dependent upon the selection made in Step 5 Select Stop Zone Type OR Zone Type Restore Select an option from the displayed list which is dependent on the selection made in Step 5 Select Start System Operation OR System Operation 1 Select an option from the displayed list which is dependent on the selection made in Step 5 Select Stop System Operation OR System Operation 2 Select an option from the displayed list which is dependent on the selection made in Step 5 Use the W button to advance to next page then select Zone Number Operation to toggle between options Select the First Second or Third Start Zone then select a Zone from the displayed list Select the First Second or Third Stop Zone then select a Zone from the displayed list Select Save when programming is complete Select the S button or press the Home key to return to the Automation programming or the Home screen Delete a Rule At the Rules screen select the Rule to edit or delete Select
Download Pdf Manuals
Related Search