Invicta TURN Informaion
Contents
1. x W M W W E EE FLOOR PROTECTOR LAID ON JOIST Combustible floor leg timber Insulative board 6mm non combustible finish pd OBLICA TURN INSTALLATION AND USER MANUAL PAGE 7 3 INSTALLATION Non combustible finish Combustible eg tiles floor eg timber Concrete 80mm 1180mm Floor protector uad ds floor eg Timber OBLICA TURN INSTALLATION AND USER MANUAL PAGE 8 4 OPERATION 4 1 What you should burn Untreated air dried hardwood Split logs with a humidity content of less than 20 4 2 Do not burn Trash Painted plastic Coated or preservative treated wood e Waste or black coal Inflammable liquids Fire gels Moist wood with a residual humidity content of more than 20 this may cause soothing of the chimney IMPORTANT Misuse may lead to unhealthy and environmentally harmful emissions and will void any warranty or guarantee The maximum load capacity for the Turn is 10kg of wood Burning only seasoned hardwood helps to protect the environment and lower emissions For details of a wood supplier in your area please call our office on2. D 8 m 36 3 c 3 a 3 2 IMPORTANT Frames must also be considered Timber window frames must be treated as combustible surfaces see 2 3 Aluminium frames can be treated as non combustible surfaces see 2 2 OBLICA TURN INSTALLATION AND USER MANUAL PAGE 4 3 INSTALLATION 3 1 Typical flue kit installation yon Cowl Chinaman Hat 8 Outer Case L 10 Outer Case RUBBER DEKTITE FLASHING 6 Active Flue imm 8 Outer Case umu 222 10 Outer Case A 22 222 N AZ CEILING RING gt m EA a 8 Outer 22 decorative 2 casing 6 Active Flue 22 Crimped end up L 2 dec outer case a 22 8 Outer decorative gt E casing NN FIREBOX A OBLICA TURN INSTALLATION AND USER MANUAL PAGE 5 3 INSTALLATION 3 2 Installing the external flue 1 Place the connection piece inside the suspension bracket This will join the single skin flue below the bracket and the triple skin flue above the bracket which have different diameters 2 Ensure the
3. triple skin flue is installed as per Australian standards see diagrams below PITCHED ROOF INSTALLATION The top of the flue must be 400mm higher than the highest point of the roof Alternatively there must be a minimum distance of 8 meters from any higher section of roof 240 cm po 28 m gt 40 cm FLAT ROOF INSTALLATION LESS THAN 5 PITCH The top of the flue must be 1200mm above the roofline Alternatively there must be a minimum distance of 8 meters from any higher section of roof v OBLICA TURN INSTALLATION AND USER MANUAL PAGE 6 NE z40cm V e 3 INSTALLATION 3 3 Protecting the floor Any combustible floor beneath a fireplace must have a floor protector that extends 300mm beyond the diameter of the firebox in all directions e If installed directly on combustible material the floor protector must be made of a minimum 6mm thick cement sheet Non combustible finishes can be applied to the floor protector tiles steel sheet light concrete etc e f the combustible floor is installed on concrete you can replace the combustible material with non combustible material laid directly onto the concrete FLOOR PROTECTOR LAID ON TIMBER FLOOR Combustible Insulative board 6mm floor eg timber non combustible finish
4. 03 9416 0400 or email info doblica com au Do not use flammable liquids or aerosols to start or rekindle the fire Do not use flammable liquids or aerosols in the vicinity of the fireplace when operating Do not store fuel within prescribed installation clearance distances The use of some types of preservative treated woods as a fuel can be hazardous OBLICA TURN INSTALLATION AND USER MANUAL PAGE 9 9 TESTING TEST REPORT NO 30A 13 0024 TRP 335261 0 TESTING LABORATORY MANUFACTURER MODEL WORK REQUESTED TEST DATES INVESTIGATING OFFICERS RESULTS CONCLUSION OBLICA TURN INSTALLATION AND USER MANUAL Vipac Engineers amp Scientists Port Melbourne VIC 3207 Skantherm GMBH Turn fireplace Assessment of appliance to AS NZS 4012 1999 for determination of Power Output and Efficiency and AS NZS 4013 1999 for Flue Gas Emission using hardwood fuel 29 10 2013 to 18 11 2013 Christian Schmidt Rebecca Searcy The appliance particulate emission factor established in testing is 2 9g kg of dry wood within the maximum specification of 4 0g kg of dry wood This appliance does comply with the requirements of AS NZS 4013 1999 for the configuration tested PAGE 10
5. SKANTHERM TURN INSTALLATION AND USER MANUAL 1 TECHNICAL DATA i 2 PRE INSTALLATION 3 3 INSTALLATION d 4 OPERATION 9 J TESTING 10 Keep for future use OBLICA 200 Argyle St Fitzroy VIC 3065 03 9416 0400 Irewor 1 TECHNICAL DATA WEIGHT AND DIMENSIONS Dimensions W1150 x H852 x D382mm Firebox weight 213kg Flue kit Standard 6 DETERMINED UNDER TEST CONDITIONS Nominal thermal output kW Efficiency 78 490 o FLUE Standard 6 5 MU ua M EPL EE Vi 1150 OBLICA TURN INSTALLATION AND USER MANUAL PAGE 2 2 PRE INSTALLATION Congratulations on your purchase of the Turn This appliance should be installed and checked by a qualified professional Ensure you have read the operation guidelines thoroughly prior to first use For any questions or concerns please contact Oblica on 03 9416 0400 The installation process is outlined below Determine position of firebox and flue carefully observing the clearances described within this section Install the external flue Install the internal flue and engage the firebox Ensure the floor has adequate protection CAUTION Using components or parts other than those provided by the manufacturer or modifying the specification of components may result in inferior or unsafe operation If such actio
6. n is necessary consult the manufacturer in the first instance The appliance and flue system must be installed in accordance with AS NZS 2918 and the relevant building code or codes Any modification of the appliance that has not been approved in writing by the testing authority will be in breach of the approval granted for compliance with AS NZS 4013 Once the flue has been installed and approved by a professional installer the flue must not be modified in any way OBLICA TURN INSTALLATION AND USER MANUAL PAGE 3 2 PRE INSTALLATION MINIMUM CLEARANCE INTERNAL 2 1 Clearance from non combustible surfaces 2 3 Clearance from combustible surfaces eg masonry eg timber joist amp concrete 100mm minimum clearance is required from fully Clearances may be reduced with the application of non combustible surfaces heat shielding to walls in accordance to the Australian Building Code Non Combustible LLLLLLLLLLLLLL For information on heat shielding please contact our office on 03 9416 0400 or email infoldoblica com au Configuration 1 Parallel installation e qsnquio Combustible D d 244442 uy f 3 WE 2 2 Clearance from glass Zo e 900mm minimum clearance is required from normal 6 non combustible glass 390mm minimum clearance is required from toughened glass Glass Configuration 2 Corner installation frameless or aluminium frame a 3
Download Pdf Manuals
Related Search