DriveIT Low Voltage AC Drives Quick Start Guide ACS550
Contents
1. Loc C 400RPM 1200 RPM 12 4 A 405 dm3 s instructions to configure ai the system ID D WJ Note For common parameters and menu items use the Help key to display descriptions If you encounter Alarms or Faults use the Help key or refer to the Diagnostic section of the User s Manual Basic Control Panel The Basic Control Panel does not include the Start up Assistant Refer to the Start up Section of the User s Manual and manually enter any parameter changes desired Code 3AFE 68243513 REV A EN Effective September 9 2003 Supersedes NONE2. language on the inside plastic shell Install the Wiring Wiring Power 1 On the motor cable 6 Open the appropriate knockouts in the gland box Install the cable clamps for the power motor cables On the input power cable strip the sheathing back far enough to route individual wires strip the sheathing back far enough to expose the copper 6 wire screen so that the screen can be twisted into a pig tail Keep the short pig tail short to minimize noise radiation Route both cables through the clamps IP2001 6 Strip and connect the power motor wires and the power ground wire to the drive terminals See below or Power Connections in User s Manual Connect the pig tail r created from the motor 8 pe J 2 cable screen Na tel Install conduit gland box and tighten the cable clamps SELLS A X0005 A Warning For floating networks remove screws at EM1 and EM3 on Frame sizes R1 R4 Power Input Power Output to Motor U1 V1 W1 U2 V2 W2 Optional Braking Terminal R1 R2_ BRK BRK 3 R4 UDC UDC e Braking unit e Chopper and resistor Warning For floating networks remove A screws at F1 and F2 on Frame sizes R5 or R6 Frame Size R5 F1 PE Power Input U1 V1 W1 Power Output to Motor U2 V2 W2 Optional Braking Frame Termin
3. as specified oi Motor cable is routed away from other cables NO power factor compensation capacitors are connected to the motor cable Control terminals are wired and tightened as specified NO tools or foreign objects such as drill E The input power mains fuses mains switch shavings are inside the drive NO alternate power source for the motor is connected no input voltage is applied to the output of the drive Re install the Cover 1 Align the cover and slide it on 2 Tighten the Captive screw 3 Re install the control panel Apply Power Always re install the front cover before turning power on Warning The ACS550 will start up A automatically at power up if the external run command is on 1 Apply input power When power is applied to the ACS550 the green LED comes on Note Before increasing motor speed check that the motor is running in the desired direction Start up In Start up enter motor data collected earlier and if needed edit parameters that define how the drive operates and communicates Assistant Control Panel The Start up Assistant steps through typical start up selections and runs automatically upon the initial power up At other times use the steps below to run the Start up Assistant 1 Use the MENU key to access the Menu list 2 Select Assistants 3 Select Start up Assistant 4 Follow the screen ANE a ea E
4. Drive Low Voltage AC Drives Quick Start Guide ACS550 01 Drives 0 75 90 kW _e Overview The installation of the ACS550 adjustable speed AC drive follows the outline below Task PREPARE for installation UNPACK the drive PREPARE mounting location REMOVE the front cover MOUNT the drive INSTALL wiring CHECK installation RE INSTALL the cover APPLY power START UP AL ED ED FADD EP Application This guide provides a quick reference for installing ACS550 01 drives having a standard enclosure Note This guide does not provide detailed installation safety or operational instructions See the ACS550 User s Manual for complete information Prepare for Installation A Warning The ACS550 should ONLY be installed by a qualified electrician Check e Motor compatibility Motor type nominal current frequency and voltage range must match drive specifications e Suitable environment Drive requires heated indoor controlled environment that is suitable for the selected enclosure e Wiring Follow local codes for wiring circuit protection and EMC requirements Refer to User s manual and confirm that all preparations are complete Tools Required Screwdrivers wire stripper tape measure mounting screws or bolts and drill Drive Identification ACS550 01 08A8 4 Us tong ey eee MINNN Py Pra 4 3kW Ser no 2030700001 Use the following chart to interpret the t
5. al Brake Options R5 R6 UDC UDC Braking unit e Chopper and resistor Frame Size R6 Power Input U1 V1 W1 9 Install the cable clamp s for the control cable s Power motor cables and clamps not shown in figure X0006 Wiring the Controls 1 Strip control cable sheathing and twist the copper screen into a pig tail 2 Route control cable s through clamp s and tighten clamp s 3 Connect the ground screen pig tail for digital and analog I O cables at X1 1 4 Connect the ground screen B J pig tail for RS485 cables at 1P2003 X1 28 or X1 32 5 Strip and connect the individual control wires to the drive terminals For details or other configurations see Control Connections in the User s Manual x1 Signal cable shield Ext freq ref 1 0 10 V Analog input com Ref voltage 10 VDC Not used 6 AGND Analog input c
6. om 20 8 AO2 Output current 0 20 mA 9 AGND Analog output com Aux volt output 24 VDC Aux volt common DCOM Digital input com for all a 13 DI1 Start Stop Active start 14 DI2 Fwd Rev Active rev dir Constant speed sel 16 Di4 Constant speed sel 17 DI5 Ramp pair Active 214 ramp pair m8 Di6 Not used 5 pB Relay output 1 Default operation Ready 19 21 connected Relay output 2 Default operation Running 22 24 connected Relay output 3 Default operation Fault 1 25 27 connected Fault gt 25 26 connected Note 1 Jumper setting Al1 0 10 V H Al2 0 4 20 mA Note 2 Code 0 open 1 connected ILLI O 0 Reference through Al 1 JO CONSTANT SPEED 1 1202 oo mo CONSTANT SPEED 2 1203 CONSTANT SPEED 3 1204 6 Install the conduit gland box cover 1 screw Check Installation Before applying power perform the following checks Eronen conforms to specications ire arves mounted secwey Proper cooing space aoundithe dive oror ana avn equipment are ready for ar Floating networks Internal RFI filter disconnected i Drive is properly grounded Input power mains voltage matches the drive nominal input voltage a The input power mains terminals U1 V1 W1 are connected and tightened as specified installed The motor terminals U2 V2 W2 are connected and tightened
7. ype code found on the drive label ACS550 01 08A8 4 AC Standard Drive 550 ears Construction region specific 01 Setup parts for IEC instal compliance U1 Setup parts for US instal compliance Output current rating See Ratings chart in User s Manual for details Voltage rating 2 208 240 VAC 4 380 480 VAC Enclosure protection class No specification IP 21 UL type 1 NEMA 1 B056 IP 54 UL type 12 NEMA 12 Collect Motor Data Collect the following data from the motor nameplate plate for later use in the ACS550 startup e Voltage e Nominal motor current e Nominal frequency e Nominal speed e Nominal power Unpack the Drive Note Lift ACS550 by its chassis and not by its cover Unpack the drive Check for any damage Check the contents against the order shipping label Prepare the Mounting Location 1 Mark the mounting points Remove the Front Cover A Mount the Drive 1 The drive requires a smooth vertical solid surface free from heat and moisture with free space for air flow 200 mm 8 in above and below and 25 mm 1 in around the sides of the drive Drill the mounting holes Remove the control panel if attached Loosen the captive screw at the top Pull near the top to remove the cover Position the ACS550 and use screws or bolts to securely tighten all four corners Attach a warning sticker in the appropriate
Download Pdf Manuals
Related Search