Manual - Graupner
Contents
1. battery cells are inserted incorrectly the transmitter will not function The figure on the left shows the transmitter 10 whose functions are explained below with its operating elements 1 to 9 4 With the slide switch 1 on the transmitter the green LED HIGH 2 lights up Note if the red LED LOW lights up the 8 battery cells must be changed in the transmitter With the stick 3 pitch and yaw functions are controlled in heli mode in flight mode the motors speed and the rudder func tion Please note the function depends on the speed control of the motors not on the rudder If the stick 3is pushed forward the pitch or the motors speed increases If the stick is moved to the left the model will turn in helicopter mode and in airplane mode to left If the stick is moved to the left the model will turn in helicopter mode and in airplane mode to left With the stick 4 in helicopter mode Nick functions in flight mode the elevator and the roll aileron function are oper ated With the switch 5 the 4 motor gondolas can be rotated of about 90 With this switch you can also change from heli to plane mode The switch 6 is not necessary and has no function Through the slide switches 7 Servo reverse the direction of servo rotation can be reversed this is not normally required please keep the default settings The button 8is required to bind the transmitter to the receiver The transmitter is already bound to the re2. The attitude of the model must always be clearly visible throughout the flight to ensure always a safely use and avoid problems Familiarize yourself during the flight if any mal function interference becomes noticeable the landing must be initiated immediately for safety reasons You always give way to other aircraft Start and landing strips should be kept free of people and other obstacles 9944 RTF_jh_V1 Required tools and adhesives not included Model assembly Allen key 1 5 mm Cyano glue No 5821 Activator for cyano glue No 953 150 Phillips Screwdriver These items are required for any repairs The model is ready to fly after a few adhesive or assembly steps the following instructions should be observed carefully so that safe operation is ensured ra Gluing the rudder 2 to the fuselage 1 For this purpose on both sides thin the enclosed contact adhe sive to the bonding surfaces let the glue dry for about 1 minute then put off the rudder 2 and press firmly A Inserting the landing gear 3 in the fuselage 1 9944 RTF jh VI Installing the LiPo battery WARNING A Safe use of the battery charger Persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge or not capable to use safely the charger must not use the charger without supervision or instruction by a responsible person The battery charger is made by three
3. When the LEDs stop flashing in the receiver then the trans mitter and the receiver are bound This operation can take up to 10 seconds 6 Then release the binding button on the transmitter and remove the binding jumper from the receiver 7 Check if all functions work properly 8 If the binding has not been followed properly or if the result is not as desired then repeat the process 9944 RTF_jh_V1 1 9 20 Notes on environmental protection Care and maintenance Warranty certificate 0 DISPOSAL NOTES This symbol on the product user manual or packaging indi cates that this product must not be disposed of with other household waste at the end of its life It must be handed over to the applicable collection point for the recycling of electrical and electronic equipment The materials are recyclable as marked By recycling material reusing or other forms of scrap usage you are making an impor tant contribution to environmental protection Batteries and accumulators must be removed from the device and disposed of at an appropriate collection point Please inquire if necessary from the local authority for the appropriate disposal site Notes on care The product does not need any maintenance it works so as it is without any special care In your own interests protect it from dust dirt and moisture Clean the product only with a dry cloth do not use detergent lightly rub The Graupner Henriettenstrassee 96
4. components Battery charger BC 4S15D AC DC ADAPTER for 230 V net connector Connection cable for 12 V battery as power source Use the charger only with the supplied AC DC adapter at 230 V or with the connecting cable at 12V Risk of fire The connection socket for the battery is polarised Never use force while inserting the connector It must plug easily Short cir cuit and fire risk Connect olways only one LiPo never 2 or 3 risk of fire The battery charger can be used only in dry spaces The charger should always be supervised during charge and it should be used only in rooms fitted with a smoke detector A damaged charger or power cord must not be used until they are repaired by the manufacturer his customer service or a suit ably qualified person Electric shock risk The charger is only suitable for LiPo batteries it cannot charge other types of batteries eg Nixx LiFe Pb If you connect other type of batteries to the charger both battery and charger can be damaged risk of fire and explosions A wet charger even if re dried should no longer be used Risk of electric shock Due to safety and licensing reasons CE any unauthorized reconstruction and or modification of the product is prohibited Risk of electric shock Protect the charger from dust dirt moisture and other foreign parts It must be protected from vibration as well as excessive heat or cold Do not cover the charger during charge the al
5. 0 9944 RTF_jh_V1 Declaration of conformity Graupner declares that the product is conform to CE norms Brushless motor KV 1000 EN 61000 6 1 2007 EN 61000 6 3 2007 A1 2011 ESC 12 A EN55014 1 2006 A1 2009 EN55014 2 1997 A2 2008 Servo EN 6100 6 3 2007 A1 2011 EN 6100 6 1 2007 FLIGHT CONTROL EN55022 2010 EN55024 2010 Graupner 6 channel 2 4 GHz transmitter EN 62311 EN 60950 1 A11 A1 A12 A2 EN 301 489 1 17 EN 300 328 Battery charger and adapter EN 60950 1 2006 A12 2011 EN 55022 2006 A1 2007 EN 55024 1998 A1 2001 A2 2003 9944 RTF_jh_V1 21 20 22 20 9944 RTF jh VI 9944 RTF_jh_V1 2 3 m 2 0 9944 RTF_jh_V1
6. 73230 Kirchheim Teck grants from the date of purchase of this product for a period of 24 months The warranty applies only to the material or opera tional defects already existing when you purchased the item Damage due to wear overloading incorrect accessories or improper handling are excluded from the guarantee The legal rights and claims are not affected by this guarantee Please check exactly defects before a claim or send the product because we have to ask you to pay shipping costs if the item is free from defects The warranty on batteries is limited to 6 months For this time we will only ensure that the battery fulfils its func tion only batteries which can not be more charged and dis charged any more can be replaced on warranty This does not apply to batteries in which the charge and discharge notes were not observed Batteries may only be series connected or par allel connected in exceptions since the cell capacity and charge can differ The battery packs that we supply are therefore pref erable The present construction or user manual is for informa tional purposes only and may be changed without prior notice The current version can be found on the Internet at www graupner de on the relevant product page In addition the com pany Graupner has no responsibility or liability for any errors or inaccuracies that may appear in construction or operation man uals No liability can be accepted for printing errors 20 2
7. INNOVATION amp TECHNOLOGY Groupner Manual X44 VTOL Electric model with 4 Brushless motors and 2 4 GHz transmitter 9944 RTF 6 9944 RTF jh VI Index ITS Ed AAA AA 4 Service Centre ko w ni pp nwi ewa ie ii 4 A wk pk aa ka a kan tk ki epav kw kk ka kana 5 Package CON sat a kk en 5 A aa aie a e n 6 SIS DIES al AEE 6 Required tools and adhesives not included 8 Suggested accessories not included 8 Model assembly errada 8 Installing the LiPo battery anna a ee k 9 Graupner 6 channel 2 4 GHz transmitter eeererrrreeeeereres 10 Transmitter translation from MODE ll to MODE Ll 12 Installing the LiPo Battery asien 14 The X44 FUGHT CONTROL nun are 14 Installing the propellers esos 15 PIE nee EEEE 17 Technical Dita last 17 EST S nennen a 17 Replacement parts not included uses 18 A S 19 Notes on environmental protection ccoooiccccnnocnonncconnnroooommmo 20 Care and Malta an 20 Warranty certificate asien een 20 Boris 21 9944 RTF_jh_V1 Introduction Service Centre Graupner in Internet Thank you very much for purchasing the GRAUPNER X44 This X44 is extremely versatile Read this manual carefully to achieve the best results with your X 44 and first of all to safely control your models If you experi ence any trouble during operation take the instructions to help or ask your dealer or Graupner Service Centre Due to technical changes the in
8. ceiver then this button is therefore not required The transmitter is already bound to the receiver no binding is then required If the bind ing went lost or in case you use a spare transmitter No 9944 834 please bind again See section Binding The transmitter antenna 9can be bent of about 45 upward With this position the prime properties are achieved 9944 RTF_jh_V1 11 20 Transmitter translation from MODE II to MODE Required tools A Philips screwdriver B Tweezers Hinweis First of all invert the connectors of altitude and throttle in the receiver then proceed as follows Unscrew the four screws 1 with the Philips screwdriver A and remove gently the lower transmitter cover and lay it on the left The following images show the stick gimbal as seen The mark right or left refer to the sight from the front side Seen from the back side it is inverted The image shows the right stick gimbal in the original state The spring 3 and the lever 4 must be removed for the translation 12 u 20 9944 RTF jh VI The image shows the left stick gimbal in the original state The braking spring 2 must be unscrewed for the translation The image shows the right stick gimbal after translation The braking spring 2 is correctly mounted for mode I The image shows the left stick gimbal after translation The spring 3 and the lever 4 are correctly mounted for mode I The image shows t
9. crobatic plane model in plane mode The X44 is is equipped as standard with an excellently working FLIGHT CONTROL which stabilizes the model on each axe in both plane and heli modes The X44 is a reproduction of the marine experimental plane the construction of the plane has been many times patented 9944 RTF_jh_V1 17 20 Replacement parts not included No gt gt oo 8 8 o 8 8 OO OS HH 4 6 9944 1 9944 2 9944 3 9944 4 9944 5 9944 7 9944 10 9944 12 9944 29 9944 81 9944 82 9944 83 9944 85 9944 141 9944 142 9944 830 9944 833 9944 834 9944 835 Description Canopy cover Fuselage Wing Rear wing Landing gear set Motor gondola Rudder Propellers set Propeller adapter Brushless motor KV 1000 ESC 12A Servo LiPo battery 4 1300 HoTT decals sheet Marine decals sheet FLIGHT CONTROL Motor gondolas servo Transmitter Receiver 18 20 9944 RTF_jh_V1 Binding This process is required for example if you want to bind a spare transmitter What is needed is the enclosed binding plug O No 9944 RTF ECT s JBAT Graupner Y 4 RECEIVER CS Fa 1 Insert the batteries in the transmitter 2 Plug the binding jumper in the receiver binding port BAT see the picture 3 Connect the XT 60 connector to the battery now both LEDs will flash in the receiver indicating that it is in binding mode 4 Push and hold the binding button while switching the trans mitter on 5
10. e the item its technology and equipment Intended use of the battery Graupner LiPo batteries should only be used in RC Any other use is not allowed Any other use is improper mistreatment of LiPo batteries can cause explosions fire smoke and cause poisoning Ignoring the guidance and warnings can result in poor performance and other defects Target group The product is not a toy It is not suitable for children under 14 years The installation and operation of the X44 must be per formed by experienced modellers If you do not have sufficient knowledge about dealing with radio controlled models please contact an experienced modeller or a model club 2 Rudder with adhesive 7 Battery 3 Landing gear set 8 Charger with connection cables 4 Propellers set with propeller 9 8x AA batteries adapters 5 Spare propellers set 10 Graupner 6 channel 2 4 GHz trans mitter 3 l Grounner 9944 RTF_jh_V1 5 20 Symbols explication A Safety notes CAUTION Always follow the information marked with the CAUTION or WARN ING symbol The signal word WARNING indicates the potential for serious injury the signal word CAUTION indicates possibility of lighter injuries The signal word NOTE indicates potential malfunctions ATTENTION indicates potential damages to objects General These safety instructions are intended not only to protect the product but also for your own and other people s safety There fore pl
11. ease read this section very carefully before using the product Do not carelessly leave the packaging material lying around since it might become a dangerous toy for children Persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge or not capable to use safely the speed controller must not use the speed controller without supervision or instruction by a responsible person Operation and use of radio controlled models needs to be learnt If you have never operated a model of this type before start carefully and make yourself familiar with the model s reactions to the remote control commands Proceed respon sibly e The insurance is mandatory for all kinds of model operation Always fly with a safe distance away from people and objects never fly low over people or directly towards them Never fly the model near power lines industrial sites resi dential areas public roads school yards or playgrounds etc All model flyers must behave in such a way that public safety especially other people and property as well as orderly flying operations is not jeopardized or disrupted e Inform passers by and spectators before the start of the dangers posed by your model and exhort them to keep a safe distance Also observe the accompanying warnings of battery 9944 RTF_jh_V1 CAUTION Checklist before starting Before every use check the range and functio
12. formation may be changed in this manual without prior notice Be always updated by check ing periodically on our website www graupner de to be always uptodate with the products and firmwares This product complies with national and European legal require ments To maintain this condition and to ensure safe operation you must read and follow this user manual and the safety notes before using the product NOTICE This manual is part of this product It contains important infor mation concerning operation and handling Keep these instruc tions for future reference and give it to third person in case you gave the product Take this into consideration when you pass it on to other future owner Graupner Central Service Servicehotline Graupner SJ GmbH E 49 0 7021 722 130 Henriettenstasse 96 Monday Thursday D 73230 Kirchheim Teck 9 15 am 5 00 pm Friday 9 15 am 1 00 pm For the service centres outside Germany please refer to our web site www graupner de 9944 RTF_jh_V1 Intended use Package content The X44 is a ready to fly remote controlled airplane model The X44 is designed exclusively to be used as a battery pow ered radio controlled model any other use is not allowed For any improper use no warranty or liability is accepted Read through this entire manual before you attempt to program or use the X44 Graupner SJ constantly works on the development of all prod ucts we reserve the right to chang
13. he lower hooking point for the spring 3 in detail 9944 RTF_jh_V1 13 20 Installing the LiPo battery CAUTION The X 44 FLIGHT CONTROL First of all open the cabin canopy To open hold it securely lat erally and pull to the top The image shows the LiPo battery already installed Risk of injury by rotating propellers motors can start up in an uncontrolled manner when the XT 60 connector of the battery is connected Always install the propellers only after review Fuselage bottom with FLIGHT CONTROL and receiver right servo for the motor gondolas adjustment left The FLIGHT CONTROL is a highly complex electronic unit that aerodynamically stabilizes the model over several gyros Both aileron elevator of the rear wing and the speed control of each brushless motor are controlled by this unit NOTICE Note that the model has to be hold after connecting the XT 60 connector in a stable position on a flat surface until the gyros of FLIGHT CONTROL have initialized This process takes a few seconds and is confirmed by several beeps of the motors The motor gondolas run first on a 45 position Only after this oper ation the FLIGHT CONTROL is functionally ready 14 20 9944 RTF jh VI Note that the two rear motor gondolas are inclined in the verti cal neutral position approximately 2 forward this is not a defect but for optimal flight characteristics it is so required Also note that all rudde
14. l in light wind Start the model first vertically in heli mode and practice hovering in low altitude A trimming of the model after the first start is necessary over the trim sliders below or next to the sticks Due to the excellent working of the FLIGHT CONTROL a trimming is usually not necessary Always land against the wind direction with enough battery capacity For take off and landing in the airplane mode an absolutely smooth runway is needed because the X44 wheels are insufficient on a grass runway Note that the flight time is essentially dependent on the flight mode used on the LiPo battery quality and capacity A flight time of 3 6 minutes is normally reached with the X44 Attention Note that the XT 60 connectors have to be unplugged after every use for safety reasons and to preserve the LiPo battery from deep discharge Technical Data Wing area 7 35 dm Rear wing area 9 15 dm Weight 855 y Total surface area 16 5 dm Length 860 mm Wingspan 695 mm Wing load 51 8 g dm Features The Graupner X44 is an innovative VTOL electric model which has very particular flight characteristics VTOL means Vertical Take Off and Landing The X44 is equipped with 4 brushless motors which can be rotated of about 90 by a switch on the transmitter in this way you can convert before or during the flight from heli to plane model or vice versa The X44 flies in heli mode as an helicopter and can be flown as an a
15. ning For this purpose switch on the transmitter and the receiving system Check that all controls are in neutral position function prop erly and turn down the correct side When flying a model aircraft for the first time it is advanta geous if an experienced helper stands aside in the review and the first flights Propellers powered by a motor represent a constant risk of injury Do not touch them with any part of the body A fast ro tating propeller can cut off a finger Keep well out of the rotational plane of the propeller A part of it or the entire propeller could broke and fly off at high speed hitting you or third parties This can cause serious injury Make sure that no object gets in touch with a revolv ing propeller The blockage of the propeller for any object must be excluded Check each time before the model itself and everything attached to it e g propeller tailplane etc is in good condi tion and undamaged The model may be taken in operation only after removal of all defects Radio interference caused by unknown sources can occur without warning The model is then uncontrollable and com pletely unpredictable Do not leave the radio control system unattended to prevent operation by third parties Electric motor should be activated only if there is nothing in the rotational plane of the propeller Do not attempt to stop the spinning propeller Power the electric motors only with the propeller installed
16. r deflections are factory set correctly and the control surfaces move when LiPo battery is connected if you tilt or rotate the model Installing the propellers CAUTION Risk of injury by rotating propellers when motors are running Always unplug the XT 60 connector to the LiPo battery before working on the propellers Arrangement of the propellers A clockwise rotation and B coun ter clockwise rotation 9944 RTF_jh_V1 1 5 20 Propellers rotation sense 1 Clockwise motor 2 Counter clockwise motor propeller L propeller R 4 Counter clockwise motor 3 Clockwise motor propeller R propeller L CAUTION A e e Pi EEE Risk of injury from flying debris Loose mounted propellers can come loose during operation Always check whether the propel lers are mounted properly The centre of gravity The centre of gravity of the X44 is located 121 131 mm from the wing leading edge If the recommended LiPo battery is used the centre of gravity is automatically correctly adjusted The centre of gravity can be tested for control by holding the model with two fingers in the centre of gravity under the wing The model should be balanced and levelled The sketch shows the model with vertical motors in this case the centre of gravity is at 121 mm measured from the wing leading edge 16 20 9944 RTF_jh_V1 First flight First of all fully charge the Li Po battery as described above Then fly the prepared mode
17. uminium body has a cooling function and must be free Risk of fire The charger and the battery to be charged must be placed on a non combustible heat resistant and non conducting surface during operation Do not use the charger near easily flammable materials Always disconnect the charger from the power supply when it is not in use Read the safety instructions that came with each LiPo battery before charging use for charging the included LiPo charger 9944 RTF_jh_V1 Charger assembly with supplied adapter for 230 V If in the digital display of the LiPo charger appears FUL the LiPo battery is fully charged Thereafter disconnect the LiPo battery from the charger and pull the plug out of the power adapter Charger assembly with supplied charge cable with two crocodile connec tors for 12 V batteries Graupner 6 channel 2 4 GHz transmitter CAUTION The transmitter 10 is fully configured to Mode 2 and already bound to the receiver in the model The transmitter can me translated in mode 1 see next section to let the transmitter work properly insert the included 8 x AA battery cells 9 in the back of the transmitter paying attention to the correct polarity The included dry AA battery cells must never be recharged Risk of fire and explosions 10 20 9944 RTF_jh_V1 Note Make sure that the polarity is correct The and signs in the transmitter and on the battery cells must match If one or more
Download Pdf Manuals
Related Search