BL100 Installation Guide
Contents
1. is enrolled If the MPC is not changed none of the functions in the deadbolt except deadbolt initialization are available If no Administrator User is registered Ordinary Users cannot be enrolled either note For instructions on how to change the Master Pass Code Enroll Administrator User or Enroll Ordinary User please see BL100 Fingerprint Deadbolt User Manual 2 Do not remove batteries when matching enrolling or deleting fingerprints because the sudden power loss may result in data loss of fingerprint templates Prior to removing batteries make sure the deadbolt is not being operated 3 It is recommended to replace the deadbolt batteries at least once every six months to avoid 5 Battery Low Voltage Protection damaging the deadbolt s electronics due to the battery corrosion Do not use poor quality batteries When the AA batteries are running low the deadbolt s low voltage alarm signals users to change the batteries as 3 LED Backlight Indicators follows The LED Backlight Indicators contain three colors Red Green and Blue 1 When the battery voltage reaches lower than 4 8V the alarm buzzer will make a short sharp sound five The general rule times Users can unlock the deadbolt normally but will not be able to enter the administrative user mode Successful user operation The buzzer sounds once and the LED indicator will turn green for 3 seconds 2 When the battery voltage reaches lower than 4 5V the alarm buz2. brand Don t mix and match new and used batteries 4 Regularly check whether screws are loose Tighten screws when necessary
3. he screwdriver into the cross shaped hole of the Deadbolt Body When you rotate the cylinder bottom of the deadbolt body clockwise it springs out automatically as shown in Figure 7 When you rotate the cylinder counterclockwise 3 Install the front panel assembly into the matching hole on the door There are three holes on the Deadbolt it sorings back automatically as shown in Figure 8 Body as shown in the preceding figure The cylinder on the fore plate composition must be pulled out from the cross shaped hole of the Deadbolt Body and the locking bar must be vertical to the ground as shown in Figure 13 4 Install the back lining plate to the mapping hole Pull the connecting wire out of the oval shaped hole of the back lining plate As shown in Figure 14 attach the back lining plate and front panel assembly using a screwdriver as shown in Figure 15 Silicone Pad Back Lining Plate Figure 7 A Figure 8 IV Install the Front panel Assembly 1 Install the Silica gel backing plate on the Front panel Assembly as shown in Figure 12 Connecting Line Oval shaped Hole Figure 14 Figure 15 A gt Locking Bar f Vertical i Spring Bolt Connecting Line Figure 12 Front panel Assembly Figure 13 3 Place the silica gel backing plate on the rear panel assembly turn the lock button to make the hole slot V Install the AA Batteries vertical to the ground and insert locking bar into the hole slot see F
4. igure 19 below In this case when you 1 Obtain four AA batteries preferably same brand turn the lock button the latch bolt can spring out or back automatically 2 Insert the batteries into the Rear panel Assembly properly As shown in Figure 16 1 and 16 2 AA batteries Po AN gt i y ih Hi Vertical Hot sa PP Slot Rear panel Assembly l Lock Button gt Figure 19 Uh ES Figure 20 Figure 16 1 Figure 16 2 4 Place the rear panel assembly on the door to ensure that it can cover the whole back lining plate Install screws and tighten them using a screwdriver as shown in Figure 20 VI Install the Rear panel Assembly Vil Operating Instructions 1 Pull the connecting wire into the plug slot of the rear panel assembly as shown in Figure 17 1 Panel Description 1 Fingerprint Sensor 6 Mounting Screw 2 Lock Unlock button LED Statu Holes JOE Le o 3 a a PE VOD 3 Numerical keypad 4 Key Hole cover Connecting Line Figure 17 _ o Figure 18 E 9V batt 2 Tuck the connecting wire as shown in Figure 18 G Emergency 9V battery connector 2 Precautions 1 After the deadbolt lock is installed the deadbolt is in the test state and therefore any fingerprints and PIN codes can open the deadbolt lock Therefore you must first change the Master Pass Code MPC The deadbolt can be used normally only after an Administrator User
5. ll Check door dimensions and determine desired door swing 1 Installation Requirements S s Eog BL100 INSTALLATION GUIDE Date 2012 3 16 The fingerprint deadbolt can be installed on doors of 1 5 2 inches 35 50 mm in thickness 2 Check the direction in which the door is being opened i e right or left handed swing and align the deadbolt s I Quick Reference latch bolt accordingly A Quick reference for Installation Guide Il Check door dimensions and determine desired door swing 1 The deadbolt s body outside and inside must align properly Assume you are standing outside the Ill Install Deadbolt Body room structure and facing a door Basically there are four door opening directions Left inward left IV Install the Front panel Assembly outward right inward and right outward Left inward outward means the door swings inward outward V Install the AA Batteries with hinges on the left right inward outward means the door swings inward outward with hinges on the VI Install the Rear panel Assembly right see Figure 1 below VII Operating Instructions VIII Routine Maintenance 2 Determine the deadbolt s correct alignment positioning based on the door s opening direction see Figure 2 below B List of Lock Accessories Keyhole Screw 4 PCS Po Indoor Front panel 4 PCS AA Batteries Assembly A SO A d Left Inward Right Inward Silica gel I Indoor Indoor Rear panel backing a
6. lling the deadbolt body make sure its positioning is consistent with the direction of the symbol ___26mm Door Edge SN 60mm ta gt A Wee The hole of spring bolt A A should be in the middle 9 line of the door thick A gt Figure 4 1 Figure 42 Y Figure 5 Set the length of the deadbolt body based on the distance from the Door Edge to the center of the circle the opening hole distance is about 2 inches 65 mm as shown in Figure 4 1 The opening distance matching the default length of the deadbolt body is 2 inches 60 mm If the distance of 2 inches 70 mm is required reset the length of the deadbolt body by following these steps 1 Figure 4 2 Hold part of the Deadbolt Body rotate part 2 by 45 and pull back part 2 2 Rotate part 2 by 45 in the other direction to make the hole on part 2 match with the hole of 2 inches 70 mm on the lock body Onote When you shorten the length of the Lock Body perform the following steps 1 Hold part rotate part 2 by 45 and push part 2 ahead 2 Rotate part 2 by 45 in the other direction to make the card pillar of the lock body be embedded into the matching card hole of 2 inches 60 mm 4 3 After the procedure is completed secure the Deadbolt Body using a screwdriver as shown in Figure 6 2 Stretch the spring bolt back to the Deadbolt Body and pull the connecting wire out of the hole at the Insert t
7. ssembly k oft A Left Outward Right Outward s 4 Lock body Screw 2PCS nal ESS Figure 1 Figure 2 Back Lining 5 10 Key 2PCS Plate 3 To set the deadbolt as Left Open or Right Open on the Rear panel Assembly reference Figure 3 5 UN IN nn ae Left Open y NUN Left Open if a n Right Oper lt UN ae ao SO R 1 ght Open Left Open Figure 3 As shown in Figure 3 there is a Left open Right Open set switch on the rear panel assembly of the deadbolt Note the user can turn the switch to the left side L to set the door s opening direction as Left Open or turn the switch to the right side R to set the door s opening direction as Right Open Before installing the deadbolt you must first determine the door s opening direction as either left open or right open 2 According to the door s opening direction switch the Left Right Open set switch to the corresponding position For Left Open position the switch to the left side For Right Open position the switch to the right side lll Install Deadbolt Body 1 Determine the desired installation height and position of the deadbolt in relation to the door then adhere the hole drilling template to the door accordingly see Figure 4 1 below 2 Insert the deadbolt body into the matching hole slot see Figure 5 below LAS note There is an fUP symbol on the deadbolt body Before insta
8. zer will make a short sharp sound five Failed user operation The buzzer sounds short tone twice and the LED indicator turns red for 3 seconds times and then the deadbolt will power off Verify State LED flashes Green Management Mode Blue LED will turn on and green LED will turn off Warning Indication The buzzer beeps five times intermittently Cae When the low voltage alarm occurs please change the batteries immediately to help prevent data loss It is suggested to change the batteries immediately when the battery voltage is lower than 4 8V 4 Unlock with an Emergency Mechanical Key You can open the door using an emergency mechanical key in case the electronic component does not operate Use your fingernails or a hard chip to remove the lock cover 2 Insert the key into the keyhole and rotate 90 to unlock VIII Routine Maintenance 1 The deadbolt s surface should not be exposed to corrosive substances Otherwise the protective layer of the deadbolt s surface may be damaged and therefore the glossiness of the deadbolt surface may decrease To keep the deadbolt surface glossy use furniture polish i e Pledge wax to polish the deadbolt lock regularly 2 Use a soft dry cloth to wipe built up dirt on the fingerprint sensor after being used for a long time 3 Change the batteries immediately when the low battery power alarm sounds We recommend replacing the four old batteries with four new batteries of the same
Download Pdf Manuals
Related Search