Unified Services Router Release Notes - D-Link
Contents
1. SMe 11 Unified Services Router Release Notes D Link 8 X 509 certificate expired issue 9 Security Vulnerabilities Addressed uPnP vulnerabilities identified in the audit of libupnp code base Reference CVE 2012 5958 CVE 2012 5959 CVE 2012 5961 CVE 2012 5962 CVE 2012 5963 CVE 2012 5964 CVE 2012 5965 Solution Patched Intel SDK libupnp v1 3 1 to add the following 1 use snprintf and strncpy instead of sprintf and strcpy 2 While doing a strncpy check if we are copying more bytes than the destination string size 10 DNS query issue for L2TP WAN type 1 05B53 1 DSR 250 and 250N don t show Logs for tunnel disconnect and Logout for SSL VPN amp port forwarding 2 LAN clients page is not displaying the connected information 3 CLI wani status does not show want physical interface information when device is in RU firmware dual PPPoE mode 4 When server IP is configured with FQDN Wan L2TP over DHCP connection does not reconnect after device reboot 5 Default VLAN is associated with all the wireless SSID after reboot 6 Block ICMP is not work for a SSL VPN policy with permit permissions 7 Traffic is not going from PPTP L2TP client to device s LAN after changing WAN ISP until disable and enable PPTP server again 8 When the user login SSL portal with wrong credentials domain name in IE browser address bar the browser will not refresh back to SSL portal login page2. 9 Dyndns name provided in the SSL portal page will be changed into the device WAN IP if the user try to login SSL portal page with wrong credentials in Firefox browsers 10 Device s MAC address field in WDS page is blank in RU image 11 Device is taking 40 50 seconds to apply the configuration in VLAN page of RU image 12 Wireless client status page is showing wrong Authentication and Encryption types 13 Device GUI is getting stuck after running bulk traffic over PPTP L2TP tunnel 14 Connect button is not working for IPv6 gw gw policy in Active VPNs page when IPv6 WAN is radvd IP NW AYY SAE link Unified Services Router Release Notes D Link 15 No information on WLAN Domain when country code is set to Japan 16 Firewall rule with schedule is working correctly only for GMT time zone 17 Device displaying critical error message when trying to upload certificates to activate OpenVPN server client 18 Unable to access GUI after factory reset and power OFF ON the device 19 Wireless clients are not getting updated in Wireless Clients status page 20 UPnP process is not running in Dual Stack IPv4 IPV6 mode IPv6 to IPv4 tunneling is not work Internet web surfing is very slow for WLAN client if SPPE enabled Remove CLI command which is not supported in DSR 250 250N PPTP client is getting disconnected while uploading and downloading files BR WN e using windows shar
3. could not be saved message when user done any configuration through CLI for the first time Getting critical error when clicked save button in DHCP Reserved IP address page after upgrading from 1 01B46 HQ20130827000010 Need username and password fields for open VPN client authentication in open VPN configure page HQ20130724000015 Custom VAP active can t be enabled or disabled for device time HQ20130917000005 SSID DSR 250N_2 can be visible if the user configure active time but disabled the VAP HQ20130902000003 VLAN firewall rule is not work HQ20130930000008 Default SSIP can be visible even though WIFI disable HQ20131108000016 Need to remove the Debug log after device gets bootup in serial console HQ20131217000002 Change source IP address option for inbound traffic selector to destination IP address HQ20140121000011 LAN client page is not displaying the connected LAN clients RYE Ned lin D Link Unified Services Router Release Notes 88 When the GRE tunnel is established local PC ping to peer DSR s LAN IP address can t get response 89 Usage of extended authentication when redundant gateway check box is enabled 1 08B44 1 Security Vulnerabilities Addressed Devices respond clients some unnecessary information and hence give hackers a chance to get a non persistent root shell Reference CVE 2013 5945 CVE 2013 5946 Solution Remove all unnecessary ro
4. disconnected if file size is over 600MB 1 05B06 Bandwidth Limit not functioning when port name is used in Traffic selector PowerMode is not completely functional Wan is not getting IP from IPv6 DHCP server in stateful mode Netperf is unable to pass traffic over IPsec tunnel Transparent Mode is not supported 1 01B56 WAN interface need to take 1 1 5 minutes for link up after device power on Bandwidth Limit not functioning when port name is used in Traffic selector RYE Ned Unified Services Router Release Notes D Link 3 SSL tunnel is being disconnected when user tries to download 200 MB file 4 Admin user is not able to SSH to device 5 Device is not detecting the printer shared port 6 Wan is not getting IP from IPv6 DHCP server in stateful mode 7 Host MAC clone is not work 8 Transparent Mode is not supported 1 01B46 1 WAN interface need to take 2 3 minutes for link up after device power on 2 Bandwidth Limit not functioning when port name is used in Traffic selector 3 SSL tunnel is being disconnected when user tries to download 200 MB file 4 Admin user not able to SSH to device 5 Device is not detecting the printer shared port 6 Wan is not getting IP from IPv6 DHCP server in stateful mode 7 Host MAC clone is not work 8 PPPoE isn t working in custom MAC address 9 Transparent Mode is not supported Related Documentation Unified Services Rou
5. drive 4 In case of reboot the router checks for the presence of configuration file with format ModelName_SerialNumber cfg If found the configuration from the USB drive is restored on the router If a configuration file with the correct format is present in both connected USB drives the configuration from the first USB drive will be used to restore the router 5 The USB drive can have only one configuration with the above mentioned format for each model name 6 Ifthe USB drive is plugged in to the router which is in factory default state then during reboot no backup is taken since no custom configuration file exists in the router by that time The custom configuration is stored on the USB drive once the user clicks Save Settings in any GUI page Upgrading Instructions Upgrading by using Web UI Please use GUI upgrade feature to upgrade to this firmware version For detailed installation and upgrade instructions please refer to the Firmware Upgrades chapter in the Unified Services Router v1 09 User Manual Please upgrade corresponding firmware based your device hardware version RYE Ned D Link Unified Services Router Release Notes New Features Firmware Version New Features 1 09B32 N nu BR W L2TP client mode enhancements support MPPE and demand dialing User DB enhancements support PPTP L2TP tunnels external authentication though AD LDAP and POP3 Support Sel
6. 30425000006 Not able to establish L2TP over IPsec tunnel with same user multiple time after making changes in IPsec policy Unable to find getuserDB page in RU images HQ20130807000009 Unable to edit Roll over WAN 3G setup page Changed configuration in the configuration file is not persisting after restoring the configuration file into the device User is unable to restore the encrypted configuration file into the device Encrypted configuration file is not getting decrypted if we open the encrypted file from configtool Configuration is not getting saved into the USB After enabling the Enable Autobackup field No option to configure VLAN port membership for Port5 Port6 Port7 and Port8 through CLI Unable to get IP address to VLAN host after reboot Device is not showing any warning when trying to add duplicate VLAN ID DMZ configuration page is not available in GUI User not able to configure DNS proxy in LAN configuration page even after PPTP server disabled Bandwidth Profile Rate Functionality is not working Kernel panic when trying to connect L2TP client over IPsec SSID can t broadcast when wireless is in open mode and radio setting is n client MAC address field is showing empty in WDS page Add Help content for DMZ pages DMZ related fields are not getting highlighted immediately after enabling the DMZ option Error message should be proper when user tries to check updates in manager page without interne
7. LIABLE FOR ANY DAMAGES IN EXCESS OF THE AMOUNT D LINK RECEIVED FROM THE END USER FOR THE PRODUCT Content Important Notessa me ma a E es 3 slas AE felit ten S j Unified Services Router Release Notes D Link Problem Fixed cicsscsazevesacaneucsteccasteeaageswaeanaueteeeaseeaneeusareaeeaseeaaeaeseeeseene 7 KNOWN ISSUCS odascd EE EE EEE EE EE EEE EEE EE 14 Related Documentation ccccecceeccececceeceeueuusunseuseueeeeeueeueeausausausaueaueenenes 17 D Link Unified Services Router Release Notes Revision History and System Requirement Firmware Region Date Model HW Version Version 1 09B32_WW WW RU Mar 14 2014 DSR 250 250N A1 A2 1 09B32_RU 1 08B44_WW WW RU Oct 28 2013 DSR 250 250N A1 A2 1 08B44_RU 1 08B39_WW WW RU Oct 23 2013 DSR 250 250N A1 A2 1 08B39_RU 1 08B31_WW WW RU Jun 28 2013 DSR 250 A1 A2 1 08B31_RU 1 05B53_WW WW RU Jun 29 2012 DSR 250 DSR 250N Al 1 05B53_RU 1 05B20_ WW WW RU Mar 28 2012 DSR 250 DSR 250N Al 1 05B20_RU 1 05B20_ WW WW RU Mar 28 2012 DSR 250 DSR 250N Al 1 05B20_RU 1 05B20_ WW WW RU Mar 28 2012 DSR 250 DSR 250N Al 1 05B20_RU 1 01B56_WW WW Oct 06 2011 DSR 250N Al 1 01B46_WW WW Sep 23 2011 DSR 250N Al Important Notes 1 Automatic factory reset when image upgrade detects a firmware region mismatch between RU and WW images Such as firmware upgrade from R
8. U gt WW or WW gt RU image 2 Russian firmware version doesn t support over 40bit encrypted algorithm according to regulatory restriction 3 Microsoft Windows XP has some well known limitation to access USB storage of DSR router D Link provides a Registry Script file named WinXP reg which can solve limitation of Windows XP environment Without applying this script file it cannot copy file from Windows XP to USB storage This issue will not happen when copy file from USB storage to Windows XP RUP B44 ENAA dlinkigre e L m Unified Services Router Release Notes D Link Notes for Configuration Auto Backup Restore in USB Storage D Link DSR router series support configuration backup or restore automatically while a USB drive is inserted Following information instructs what condition will perform backup restore 1 The router configuration will be automatically backed up to the USB drive as soon as the USB drive is inserted The back name has format lt Model Name gt _ lt Serial Number gt cfg provided this USB drive doesn t have a backup configuration file from a DSR router already present 2 The system LED on the router blinks 3X in amber to indicate a backup operation has started 3 The configuration in the USB drive can be updated if the user manually clicks Save Settings in any GUI page and provided the Model Number and the Serial Number of the router matches with the file already present in the USB
9. Unified Services Router Release Notes D Link Firmware Version 1 09B32_ WW 1 09B32_RU Published Date Mar 14 2014 Copyright 2014 Copyright Notice This publication including all photographs illustrations and software is protected under international copyright laws with all rights reserved Neither this manual nor any of the material contained herein may be reproduced without written consent of the author Disclaimer The information in this document is subject to change without notice The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties of merchantability or fitness for any particular purpose The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes Limitations of Liability UNDER NO CIRCUMSTANCES SHALL D LINK OR ITS SUPPLIERS BE LIABLE FOR DAMAGES OF ANY CHARACTER E G DAMAGES FOR LOSS OF PROFIT SOFTWARE RESTORATION WORK STOPPAGE LOSS OF SAVED DATA OR ANY OTHER COMMERCIAL DAMAGES OR LOSSES RESULTING FROM THE APPLICATION OR IMPROPER USE OF THE D LINK PRODUCT OR FAILURE OF THE PRODUCT EVEN IF D LINK IS INFORMED OF THE POSSIBILITY OF SUCH DAMAGES FURTHERMORE D LINK WILL NOT BE LIABLE FOR THIRD PARTY CLAIMS AGAINST CUSTOMER FOR LOSSES OR DAMAGES D LINK WILL IN NO EVENT BE
10. blish IPV6 ipsec gwgw manual tunnel using both local amp remote traffic selectors as any 24 Upload speed for http traffic is fluctuating in the 500 1200 KBps over SSLVPN tunnel HQ20120628000015 25 When traffic is sent from WLAN to LAN or WLAN to WLAN then data trasnfer rate is varying drastically HQ20120820000010 26 CLI can t support for L2TP client configuration 27 Device is accepting the SMTP mails when Default Outbound Policy configured as Block Always without configuring the SMTP Rules Approved Mail Blocked Mail Subject List 28 VPN Tunnel is not re establishing if we initiate traffic from client 29 No GRE Tunnels status page in GUI 30 Traffic selector rule for inbound bandwidth profile with match type as MAC address is not working 31 Unable to add bandwidth profiles from CLI 32 Unable to establish L2TP client tunnel when ISP is connected as L2TP 33 Unable to establish L2TP tunnel with android phone when secret key is configured 34 Idle time out functionality is not working for PPTP users 35 Multicast packets is sent to other LAN hosts when multicast traffic running from one LAN host 36 Specific Service support for inbound traffic management is not work 1 08B39 1 PowerMode is not completely functional 2 Wan is not getting IP from IPv6 DHCP server in stateful mode 3 Netperf is unable to pass traffic over IPsec tunnel 4 PPPoE performance worst if user changes the WAN MAC add
11. c VPN tunnel are not being followed HQ20120112000014 UPnp process is not running when wan link is down User is unable to print the file from wan host with inbound firewall rule Streaming movie play is not perfect when we try listen from LAN and VLAN hosts simultaneously Wireless VLAN in general mode is not working for tagged interfaces Device should allow the user to configure UPNP on multiple VLAN subnets SIP ALG disable state User able to establish multiple calls from WAN gt LAN and LAN gt WAN Device nating the packet with WAN IP in Transparent mode Unable to drop tunnel by clicking Drop button in active VPNs page after IPSEC VPN roll over No option for SHA2 224 algorithm as Integrity Algorithm while configuring IPSec phase 2 policy through CLI WPS Session status is not displaying the current status Maximum static routes are not appearing in IPv4 Routing table and shell Unable to see logs when ips ids are enabled Active VPN s page is displaying IPsec SA established even after clicking drop button when the device in behind NAT Client is not disconnecting after user time out exceeds in PPTP L2TP server atl BN i Unified Services Router Release Notes D Link 20 Device is not able to establish OpenVpn tunnel using IPalias 21 VLAN host can t get IPV6 address 22 Client tunnel is not establishing with remote as single range subnet 23 User is unable to esta
12. ectable Outbound Interface for IGMP HQ20121210000012 Proxy ARP Allowing PPTP server range in range of LAN CLI enhancements support the space character Web GUI enhancements support auto parameters fill out in the DHCP server configuration page 3G dongle supports add Huawei E303 D Link DWM 156 A7 D Link DWM 157 B1 and D Link DWM 158 D1 8 A new click button to quickly download Dbglogs 9 A new checkbox to enable disable auto config backup 10 11 12 13 14 15 16 17 IP A new checkbox to enable disable config file encryption Support a Windows based config viewer for encrypted config files Support L2TP VPN client mode Support 5 concurrent GRE tunnels Lengthen IPSec Pre shared key length to 64 characters Simplify IGMP settings allow all net to pass through DSR by default Add package manager with single selectable 3G driver support Change IP address setting for inbound traffic management to configure LAN from server IP 1 05B53 1 Support email address to be local ID in Ipsec policy Support SHA 1 in Phase 1 Support DH group need support group 1 2 and 5 for Phase 1 Add PFS group 1 2 and 5 for Phase 2 Add a keyword with dot in Blocked Keywords text box 1 05B20 Filo BR WN 2 3 Support 3G dongle DWM 152 A1 A2 A3 DWM 156 A1 A2 A3 Huawei E1550 E173 Pre Share key can be configurable in wireless wizard Change design to disab
13. ing 1 05B20 5 Device shell is getting stuck after running bulk traffic over PPTP L2TP tunnel Bandwidth Usage and Used applications are not displayed in dashboard Default VLAN will be associated with all the wireless AP after reboot Fixing L2TP doesn t reconnects to L2TP server after reboot Fixing wireless clients is not displayed on status page Filo aon Oo Improving link up time of WAN interface less than 1 minute after device power on 1 05B06 Fixing the printer shared port detection issue Fixing SSL tunnel is disconnected when user tries to download 200 MB file 2 3 Fixing PPTP pass through is not working 4 1 Improving link up time of WAN interface to 1 1 5 minutes after device 1 01B56 power on 2 Fixing PPPoE isn t working in custom MAC address HA 2 ST ANS lt Ne D Link Unified Services Router Release Notes Known Issues Firmware Known Issues Version 1 09B32 1 PPTP passthorugh is the highest priority than PPTP firewall service 9 10 11 12 13 14 15 16 7 18 19 IPsec passthorugh is the highest priority than IKE out boundfirewall service User is unable to add DHCP reserved for wired wireless VLAN With Dlink DWA 160 Xtream N Dual Band USB adapter the WPS status displays Failed in the device WPS page even though client is connected successfully Bandwidth rules over IPse
14. le auto refresh for Traffic Monitor by default 1 05B06 Su pport SSH remote management from WAN port 1 01B46 It s the first release RUP BN link 2 Unified Services Router Release Notes D Link Changes of MIB amp D View Module Firmware New Features Version 1 05B06 Support LED and IPsec MIB 1 01B46 It s the first release SSL VPN Compatibility List SSL VPN SPLIT TUNNEL amp SSL VPN FULL TUNNEL Windows xP I E 8 0 Firefox 16 0 1 Opera 12 0 2 Google Chrome 22 0 1229 96m Windows Vista I E 8 0 Firefox 16 0 1 Opera 12 0 2 Google Chrome 22 0 1229 96m wares I E 9 0 I E 10 0 Firefox 16 0 1 Opera 12 0 2 Google Chrome I 22 0 1229 96m Windows 7 64 bit I E 9 0 I E 10 0 More eeoo O O 32 bit Fedora 13 Firefox 16 0 1 Opera 12 0 2 Google Chrome 22 0 1229 96m MAC 10 4 11 MAC Firefox 3 6 15 MAC Safari 4 1 3 45533 19 4 MAC 10 6 8 MAC Safari 5 1 7 0 MAC Firefox 16 0 1 RUP W D Link Unified Services Router Release Notes Problem Fixed Firmware Problems Fixed Version 1 09B32 1 L2tp internet connection problem HQ20120810000001 2 Device wan is unable to come up with 3G ISP with DWM 156 A5 dongle 3 Unable to pass Netperf traffic over IPsec tunnel 4 The throughput of WAN Routing mode is much lower than the WAN NAT mode 5 Traffic should run over the VPN client tunnel even when SPPE is in e
15. nabled state 6 Support NCP vpn client is able to access VLAN subnet HQ20120827000010 7 Support ARP from WAN HQ20120926000011 8 Update all pages copyright notice to 2013 9 Disabled firewall rule can t be deleted HQ20130126000001 10 SSL VPN xtunnel cab Certificate page valid date is from 8 13 2010 to 8 13 2012 HQ20130205000011 11 After initiating traffic from WLAN gt LAN wireless client is getting disconnected and unable to reconnect 12 Manual time change event is not getting logged 13 Kernel panic while running traffic from WLAN LAN hosts to internet and running traffic over IPsec tunnel when device wan is configured with L2Tp ISP HQ20130325000004 14 when device wan is configured in I2tp dhcp mode device is sending ddns membership packets to dns ip assigned by dhcp server HQ20130325000004 15 Able to login to the portal with when configured wrong secret in the radius settings page 16 Unable to get the IP for PPTP client in the device 17 Device can t detect the printer 18 Http and FTP traffic can t be transferred over IPSEC client tunnel 19 Transparent mode functionality is not working 20 Device time will not synchronize with default NTP servers after reboot sl We 7 D Link Unified Services Router Release Notes 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 HQ201
16. ot user accounts 2 After rebooting devices synchronization with NTP didn t works DRU20130424000003 Firewall rule with scheduling is not work DUSA20130125000001 1 08B39 3 1 Including 1 08B31 all fixes for DSR 250N in this version 2 The MPPE function does not work in L2TP client mode 3 Restore configuration file to different HW version 4 WAN responses ARP packet 5 Add a message to inform user who need to change 443 port number for sslvpn or remote management once two features are enabled 6 Can t work with any AP connected with network cable 7 Device time not synchronizing with default NTP servers after reboot 8 Firewall rule disable is not work unless reboot device 9 WIFI stability issue under heavy BT traffic 1 08B31 1 The OpenVPN Local Network page disappear when I used IE8 or IE9 to manage the DSR 2 USB sharing could not download upload large file 3 DWM 156 A3 A6 compatility issue 4 Security Vulnerabilities Addressed Persistent root access Reference http packetstormsecurity com files 118355 D Link DSR 250N Backdoor html Solution Removed CLI commands that could allow someone to overwrite the super user password and gain root access to the device Root user account will be completely removed in the next firmware version 5 Prevent to upload config file into different model 6 Unable to change the Wireless output power 7 Device stuck under BT download BH
17. ress 1 08B31 1 PowerMode is not completely functional 2 Wan is not getting IP from IPv6 DHCP server in stateful mode 3 Netperf is unable to pass traffic over IPsec tunnel BH IME D Link Unified Services Router Release Notes PPPoE performance worst if user changes the WAN MAC address Device got defaulted after upgrade from 1 05B73_WW to 1 08B31_WW Not able to establish L2TP over IPsec tunnel with same user multiple time after change IPsec policy The GRE function does not work The MPPE function does not work in L2TP client mode 1 05B53 Bandwidth Limit not functioning when port name is used in Traffic selector PowerMode is not completely functional Wan is not getting IP from IPv6 DHCP server in stateful mode Netperf is unable to pass traffic over IPsec tunnel Transparent Mode is not supported Observed ping loss from WLAN clients to internet 1 05B20 Bandwidth Limit not functioning when port name is used in Traffic selector PowerMode is not completely functional Wan is not getting IP from IPv6 DHCP server in stateful mode Netperf is unable to pass traffic over IPsec tunnel Transparent Mode is not supported Traffic is not going to device s LAN from PPTP L2TP client after changing WAN ISP unless PPTP server disables and then enables again Observed ping loss from WLAN clients to internet USB file sharing transmission will be
18. t connection Unable to enable DMZ from CLI Unable to add IPsec gw gw policy and firewall inbound rule on rollover WAN 3G WAN Unable to establish VPN connection in phase2 with SHA 256 HQ20130204000013 igs RY Unified Services Router Release Notes D Link 43 Low InterVLAN download speed HQ20130620000004 44 VLAN PPTP Server L2TP server and SSL client ranges and DMZ in same subnet 45 Unable to take Packet Capture on DMZ interface 46 Port translating field doesn t update in CLI after firewall rules is changed in GUI 47 Unable to upload CSV file 48 Device is displaying WLAN edit configuration page for VLAN through CLI 49 Synchronization Select Interface options of UPNP in CLI and GUI 50 Showing wrong firmware version in SSLVPN portal page 51 Able to configure the DMZ configuration without enabling the DMZ 52 User is not able to access the device CLI using SSH 53 Device is getting default when downgraded from 1 09b08 img to 1 08b39 img 54 No options are available for VLAN configuration on wan page from CLI 55 Unable to upgrade the firmware via USB 56 Error message should be proper when we try to add DMZ reserved entry without DMZ enabled 57 LAN host can t receive 6 to 4 prefix radvd IP from the device 58 Device is showing failed to open directory in CLI when log in by telnet 59 Kernel panic while running traffic over VPN tunnel 60 IPS signat
19. ter User Manual v1 09 Unified Services Router CLI Reference Guide v1 05
20. ures can t be loaded if IPS is enabled 61 ISATAP functionality is not working 62 PPTP client status through CLI is showing Disconnected even it is connected 63 Interfaces are not displaying when user configures status route through CLI 64 Improve PPTP performance 65 Improve RFC 2544 UDP performance via IXIA 66 Support DHCP option 66 tA e ST nhs D Link Unified Services Router Release Notes 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 Unable to establish the IPv6 IPSec tunnel after edit the policy GW GW tunnel can t be established when traffic selectors Subnet Range Outbound traffic over IPsec tunnel is blocked when default outbound policy is configured block always No option for L2TP mode in CLI when IPsec policy is added Kernel panic while executing VPN manual tunnel automation scripts Device is showing entry for the wireless clients which are trying to authenticate in wireless clients page Need to regenerate self signed certificates Unable to establish GRE tunnel when WAN ISP type is configured for PPTP L2TP DNS request timeout in LAN host by nslookup when IPS IDS is enabled in the device Unable to connect PPTP server using LDAP External Authentication Unable to connect L2TP server using LDAP External Authentication configuration
Download Pdf Manuals
Related Search