Instruction Manual
Contents
1. 23 24 My K Cup Reusable Coffee Filter Power Cord not shown Power Switch located rear side of Brewer Coffee Scoop BPA Free not shown All parts that come in contact with water or coffee are BPA free Set Up amp First Brew IMPORTANT Do not attempt to use your Cuisinart Single Serve Brewing System until it has been set up for its first use as Outlined below NOTE If Brewer has been exposed to temperatures below freezing wait at least two hours for Brewer to reach room temperature before brewing An extremely cold Brewer will not operate Setting Up Your Brewer 1 Unwrap cord and plug the Brewer into a grounded outlet Make sure to remove packing tape clear plastic sticker from control panel and sticker from water reservoir Also be sure to remove the polybag from the My K Cup located in the compartment on the right side of the brewer 2 Place a large cup or mug 10 oz minimum on the drip tray 3 Remove lid from reservoir then lift reservoir straight up and away from the Brewer Wash the reservoir with warm soapy water 4 Fill reservoir with water to the max fill line and return with lid to unit See figure 1 figure 1 5 Press the power switch located on the rear right side of the Brewer The switch iS spring loaded and will return to original position automatically 6 The Brewer will automatically fill the internal tank with water and heatin2. do not put your fingers in the K Cup brewing chamber 6 Lower the handle to close the brewing chamber When closed completely the control panel will indicate READY see figure 9 Note If not used within 60 seconds the unit will return to Idle mode and OPEN HEAD will be displayed on the control panel To restart the process open and close the handle and control panel will display READY again Ready Mode Yo mp DUP figure 9 All brew size icons will be displayed with the default size shown as a solid mug To choose a different size use the V or A buttons Choose from 4 oz iced beverage 6 0Z 8 0Z 10 0z and 12 0z brew sizes Note The 8 oz serving is the factory set default brew size To program your favorite brew size see Programming Your Brew Size on page 18 a Once a size is chosen press Brew Only the Brew button will be lit The control panel will now display BREWING as well as the serving size you selected see figure 10 figure 10 b To use the iced beverage setting place a tall glass filled with ice on the drip tray Use your favorite K Cup select the iced beverage brew size 4 oz and press the Brew button Once brewing is complete add more ice add cream and sugar if desired Note There may be a short pause before the brewing process begins The entire brew process lasts approximately 1 minute and ends with a burst of air to remove all liq
3. Hot Water and Rinse buttons will be illuminated Then press any of the lit buttons f the LCD control panel indicates ADD WATER check to make sure the water reservoir is properly filled If not add water If so make sure the water reservoir is properly seated in its base f the LCD control panel indicates ADD WATER even after refilling and checking the base contact Customer Service at 1 800 726 0190 The exit needle may be clogged refer to page 19 Chlorine or mineral Consider using bottled water filtered water or the Cuisinart Charcoal Water Filter taste in coffee Doesn t brew a full cup Every once in a while an air bubble may get trapped in the water path Lift off the reservoir then put it back into place Turn off and unplug the brewer for 30 seconds or more When you plug the brewer back in be sure to turn the power back on The exit needle may be clogged refer to Cleaning amp Maintenance page 18 Clean the K Cup holder brewing chamber refer to Cleaning amp Maintenance page 18 Make sure the water reservoir is properly in place and perform a Rinse cycle De scale the Brewer refer to page 20 If you have repeated the de scale procedure two times and it is still only brewing a partial cup contact Customer Service at 1 800 726 0190 The time is not You must set the clock refer to page 15 in order for the time to be displayed on displayed on the LCD the LCD ntrol panel i a If po
4. 16 aM m Gie VMDEELDEFITEL LE py ON OFF TIME SET lt TTT Set Hours Set Minutes figure 22 d If you want to set an OFF TIME Use the V or A buttons as above If not continue to Step e e To complete the process press the Menu button to set the OFF TIME Continue pressing to scroll through the remaining programming options to exit the programming mode f The ON TIME and OFF TIME functions operate independently from one another The control panel will display ON TIME SET if the ON TIME has been set The control panel will display OFF TIME SET if the OFF TIME has been set and the control panel will display ONOFF TIME SET if both the On and Off times have been set see figure 23 ON OFF TIME SET in Ready Mode ONOFF TIME SET yf gt mp DUP EZ O O figure 23 Note Depending upon the Brewer s current mode other icons will be displayed as well 17 g To turn off the ONOFF TIME SET feature press the Menu button until ONOFF TIME SET flashes Use the Y button to scroll through The control panel will display OFF after 11 pm Note The AUTO OFF timer and the OFF TIME programming options operate independently If both are set the unit will turn off at whichever time comes first Programming Brew Temperature The Brewer brews at a pre set temperature of 192 F If you prefer a cooler cup of coffee hot water tea or cocoa you may adjust this temperature
5. by the party responsible for compliance could void the user authority to operate the equipment Notes This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help SPECIAL CORD SET INSTRUCTIONS A short power supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord Longer extension cords are available and may be used if care is exercised in their use If a long extension
6. cord is used the marked electrical rating of the extension cord must be at least as great as the electrical rating of the appliance The extension cord should be a grounding type 3 wire cord and the longer cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over NOTICE Circuit Grounding If you have a Conductor diecast metal unit Connected 1 1 for your protection Properly lt it is equipped with Ve 1 a 3 conductor cord Grounding A set that has Prong a molded 3 prong B grounding type plug and should neater O be used in combi Grounding Lug gt f nation with a prop erly connected Cover grounding type Mounting outlet as shown Screw in Figure A Cover of Grounded Outlet Box RISK OF FIRE OR ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY If a grounding type outlet is not available an adapter shown in Figure B may be obtained so that a 2 slot wall outlet can be used with a 3 prong plug As shown in Figure C the adapter must be grounded by attaching its grounding lug under the screw of the outlet cover plate NOTE Do not remove the grounding prong CAUTION Before using an adapter it must be determined that the outlet cover plate scr
7. functions to exit the programming mode d AUTO OFF SET will be displayed on the control panel indicating that it has been successfully set see figure 20 AUTO OFF Set in Ready Mode AUTO OFF SET Yo mw DEP CORNY figure 20 Note Depending upon the Brewer s current mode other icons will be displayed as well e To turn off the AUTO OFF feature press the Menu button until AUTO OFF SET flashes Press the W button to advance one hour at a time until OFF appears Press the Menu button to scroll through the remaining programming functions to exit the programming mode 3 Program your Brewer for a specific ON and or OFF TIME By programming your Brewer to turn on each morning you will never have to wait for the Brewer to warm up in order to brew a gourmet cup of coffee Note To use this feature the clock must be set to the correct time Also Note the brewer must be turned off for the On Time to function VADER DEFISET ELE pp ON OFF TIME SET lt FEE Set Hours Set Minutes figure 21 a Press the Menu button until ON TIME SET flashes see figure 21 b Press or hold the or A button to scroll through the hours and minutes to your desired ON TIME The Y button is used for hours and the A button is used for minutes c After setting the desired ON TIME press the Menu button once to save your selected ON TIME You will now be in the OFF TIME SET MODE see figure 22
8. Cuisinart INSTRUCTION BOOKLET pr e O0 BEEWED F Amys Oey Single Serve Brewing System SS 780PC For your safety and continued enjoyment of this product always read the instruction book carefully before using IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed to reduce the risk of fire electric shock and or injury to persons including the following 1 READ ALL INSTRUCTIONS 2 Do not touch hot surfaces Use handles and knobs 13 14 3 To protect against electric shock do not place cord plug or base unit in water or other liquids 4 Close supervision is necessary when any appliance is used by or near children 5 Always unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance 16 6 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been dropped or damaged in any manner Return appliance to the nearest Cuisinart Repair Center for examination repair or electrical or mechanical adjustment 7 The use of accessory attachments not recommended by Cuisinart may cause injuries fire electric shock or injury to persons 8 Do not use outdoors 9 Do not let cord hang over edge of table or counter or touch hot surfaces 10 12 15 Do not place on or near a hot gas or el
9. cle is completed you can perform a Rinse or another Hot Water cycle immediately for up to one minute The RINSE and HOT WATER buttons will be lit After this time the unit will return to Idle mode and OPEN HEAD will be displayed Note To BREW directly after a Hot Water cycle open the brewing head insert a K Cup and brew as normal 12 Brewing with the My K Cup Reusable Coffee Filter The Cuisinart Single Serve Brewing System comes with a My K Cup reusable coffee filter which allows you to use your own ground coffee The dishwasher safe My K Cup conveniently stores in the easy open compartment 1 Open the storage compartment located on the right side of the Brewer by pressing the finger indent Remove the My K Cup see figure 18 Ma A r figure 13 figure 14 2 Disassemble the My K Cup by turning the lid from the holder in a counter clockwise direction Remove the filter basket from the holder see figure 14 3 Wash the My K Cup lid filter basket and holder in warm soapy water prior to use making sure to rinse and dry thoroughly All My K Cup parts are dishwasher safe 4 Insert the filter basket into the holder 5 Fill the filter basket with ground coffee making sure not to fill past the top of the mesh Adjust the amount to your personal preference Do not tamp the grinds Ensure there are no grinds remaining on the upper rim of the filter basket Turn the lid cl
10. down by 5 degrees Simply follow the instructions below 1 Press the Menu button until BREW TEMP flashes on the control panel see figure 24 AVE gt Bi ZEEE PAA Y Decrease Temp Increase Temp figure 24 2 The initial set temperature of 192 F will be displayed at the top of the control panel Use the W to lower or A to raise the temperature one degree at a time Note If at maximum temperature 192 F only the button will work and if at minimum 187 F temperature only the A arrow will work 3 Once you have reached your optimal brew temperature press the Menu button to set your default brew temperature Continue pressing Menu to scroll through the remaining programming options to exit the programming mode Note At high altitudes over 5 000 feet use the temperature adjustment to lower the temperature Programming Your Brew Size The Brewer s default brew size preset is 8 oz The default brew size lets you choose the brew size most often used To change the default brew size to your desired brew size 1 Press the Menu button until BREW SIZE flashes see figure 25 Use Y or A buttons to select your default brew size Once the desired default brew size is selected press the Menu button to set your default brew size and exit the programming mode The control panel will display your selected default brew size Note You can always select another size prior to br
11. e Center toll free at 800 726 0190 Cuisinart will be responsible for the cost of the repair replacement and shipping and handling for such nonconforming products under warranty BEFORE RETURNING YOUR CUISINART PRODUCT If your Cuisinart Single Serve Brewing System Single Serve Brewing System should prove to be defective within the warranty period we will repair or if we think necessary replace it To obtain warranty service please call our Customer Service Center toll free at 1 800 726 0190 or write to Cuisinart 7811 North Glen Harbor Blvd Glendale Arizona 85307 To facilitate the speed and accuracy of your return enclose 10 00 for shipping and handling California residents need only supply a proof of purchase and should call 1 800 726 0190 for shipping instructions Please be sure to include your return address description of the product s defect product serial number and any other information pertinent to the return Please pay by check or money order NOTE For added protection and secure handling of any Cuisinart product that is being returned we recommend you use a traceable insured delivery service Cuisinart cannot be held responsible for in transit damage or for packages that are not delivered to us Lost and or damaged products are not covered under warranty Your Cuisinart Single Serve Brewing System has been manufactured to the strictest specifications and has been designed for use only with auth
12. ectric burner or in a heated oven Always fill water reservoir first then plug cord into the wall outlet To disconnect turn controls to Off then remove plug from wall outlet Do not use appliance for other than intended use Do not lift handle to open the lid of the brewer while brewing is in progress Do not overfill the water reservoir with water Use ONLY WATER in this appliance Do not put any other liquids or foods in the water reservoir except as instructed in the cleaning instructions in this guide Do not clean drip tray with cleansers steel wool pads or other abrasive materials WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT REMOVE THE BASE PANEL NO USER SERVICEABLE PARTS ARE INSIDE REPAIR SHOULD BE DONE ONLY BY AUTHORIZED PERSONNEL SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY WARNING RISK OF FIRE OR ELECTRIC SHOCK The lightning flash with arrowhead symbol within an equilateral triangle is intended product s enclosure that may be of sufficient magnitude to constitute a risk of fire or electric shock to persons the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance to alert the user to the presence of uninsulated dangerous voltage within the 1 The exclamation point within an equilateral triangle is intended to alert the user to Warning Changes or modifications to this unit not expressly approved
13. ew is properly grounded If in doubt consult a licensed electrician Never use an adapter unless you are sure it is properly grounded Note Use of an adapter is not permitted in Canada IMPORTANT UNPACKING INSTRUCTIONS 1 Place the box on a large sturdy flat surface 2 Remove the instruction book and any other literature 3 Turn the box so that the backside of the Brewer is down and slide the coffeemaker from the box 4 After the Brewer has been removed place the box out of the way and take the packing materials 5 Remove the polybag covering the Brewer We suggest you save all packing materials in the event that future shipping of the machine is needed Keep all plastic bags away from children Contents Important Safeguards eeeeeeeeeeeeeeeees 2 Important Unpacking Instructions 4 The Quest for the Perfect Cup 5 Features and Benefits eseseeeeees 6 Set Up amp First Brew ccseceeeeeeeeeeeees 8 Setting Up Your Brewer cece 8 Charcoal Water Filter ceesseeeeeseneees 9 BrEWING sissisota e 10 Hot Water RINSE sssrini ensinei 12 Brewing with the My K Cup Accessory 13 Stopping the Brew Process 2 06 14 Adding Water cccsssecsesesseeterseesseneeneees 14 Purging the Brewer ssssssreesssesssresrsnne 14 Programi Ni xi cttven sec chavectieeets erteineteactensanan 15 Setting the Clock 0 0 ceeeeeeeeeeeeeee 15 Programming On Of
14. ewing SAN EERSTE gt BREW SIZE UNA We b Set Smaller Brew Size Set Larger Brew Size figure 25 Cleaning amp Maintenance Cleaning External Parts We recommend regular cleaning of the Brewer s external components 1 Never immerse the Brewer in water or other liquids The housing and other external components may be cleaned with a soapy damp non abrasive cloth To remove the drip tray simply slide it toward you keeping it level at all times in order to prevent spills The drip tray and drip tray plate are dishwasher safe Cleaning the My K Cup Reusable Coffee Filter 1 Open the storage compartment located on the right side of the Brewer by pressing the finger indent Remove the My K Cup Disassemble the My K Cup by turning the lid from the holder in a counter clockwise direction Remove the filter basket from the holder see figure 26 Wash the My K Cup lid filter basket and holder in warm soapy water making sure to rinse and dry thoroughly All My K Cup parts are dishwasher safe So figure 26 18 Cleaning the K Cup Holder 1 The K Cup holder is top shelf dishwasher safe use low temperature cycles in the dishwasher To remove lift the handle to open the brewing chamber Grasp the top of the K Cup holder and pull towards you After cleaning replace the K Cup holder being sure to align the arrow on the K Cup holder ri
15. f Features 15 Programming Brew Temperature 17 Programming Your Brew Size 18 Cleaning amp Maintenance 18 Cleaning External Parts 000 18 Cleaning the My K Cup Filter 18 Cleaning the K Cup Holder 19 Cleaning the Water Reservoir and Lid 19 De Scaling Your Brewer s es 20 TrOUDICSNOOTING eeeeteteeeeseeteeeeeenteeeeeees 21 Waranty oenen andas 22 The Quest for the Perfect Cup of Coffee Element 1 WATER Any hot beverage is made up primarily of water Often overlooked the quality of the water is as important as the quality of the coffee tea or cocoa A good rule of thumb is that if your water doesn t taste good from the tap it won t taste any better in your beverage That s why the Cuisinart Single Serve Brewing System has added a charcoal water fitter that removes chlorine bad tastes and odors or the purest cup every time Element 2 COFFEE While the bulk of the liquid is water all of the flavor should be from the coffee tea or cocoa To achieve the same great quality you receive at coffee bars you need to use the same quality ingredients By using the K Cup brought to you by some of the most premium brands on the market you can be assured that you re getting the finest freshest gourmet product with every cup you brew If you choose to use your own coffee in the included My K Cup make sure all your i
16. g will begin This will take approximately 4 minutes During the heating period NOT READY will be displayed on the control panel See figure 2 Heating Mode NOT READY EZ O figure 2 Note It is normal to see small amounts of water dripping into the water reservoir during this and subsequent heatings Once the water is heated OPEN HEAD will be displayed 7 When the control panel displays OPEN HEAD see figure 3 open and close the brewing chamber READY and brew size icons will be displayed with the default size shown as a solid mug see figure 4 Idle Mode Ready Mode _ YL mp DUP OPEN HEAD figure 3 figure 4 8 Making sure your mug is in place press the Brew button to start a cleansing cycle unit will dispense approximately 8 oz of water The control panel will display BREWING as well as the factory default brew size see figure 5 When cycle is complete dispose of the hot water Note Do not use a K Cup for this cycle The one time set up process is complete Charcoal Water Filter Your coffeemaker comes with a charcoal water filter that eliminates chlorine bad tastes and odors from tap water Charcoal Water Filter Charcoal Water Filter holder figure 6 Inserting the Water Filter 1 Remove the filter and filter holder from the polybags Soak the filter fully immersed in cold tap water for 15 minutes P
17. ing the control panel and reservoir will turn off Note You may get less coffee tea or hot cocoa in your cup during your next brew In order for your next brew to be the volume you have selected we recommend that you perform a rinse cycle after a terminated brew Adding Water The Control Panel will indicate when the water level in your reservoir is low or if the Reservoir has been removed by displaying the words ADD WATER The blue light in the Reservoir will also blink when water needs to be added When ADD WATER is displayed the Brewer will not allow you to brew The Water Reservoir can be filled in two ways 1 Lift off the Reservoir Lid and pour water directly into the Reservoir while it is still attached to the Brewer then replace the Lid Remove the Reservoir from Brewer by first removing the Lid from the Reservoir then lifting the Reservoir straight up and away from Brewer Fill with water place the Reservoir back on the Brewer and replace the Lid IMPORTANT Do not remove the Water Reservoir during the brewing process Purging the Brewer If your Brewer has not been used for more than one week we suggest purging the water from the inner tank 1 If there is water in the reservoir discard the water then rinse and refill with fresh water Place the reservoir back on the Brewer and replace the lid If there is no water in the reservoir simply fill Be sure the Brewer is turned
18. inse cycle only the Rinse button will be lit The control panel will display the word RINSE see figure 11 _ _ 00O figure 11 Following the Rinse cycle your Brewer will automatically fill and heat in preparation for the next cycle Once the heat cycle is completed the RINSE and HOT WATER buttons will remain lit for one minute While buttons are lit you can perform another Rinse cycle or dispense Hot Water without opening the brew chamber Note To BREW directly after a Rinse cycle open the brewing head insert a K Cup and brew as normal To make Hot Water 1 Place a cup or mug on the drip tray If you ve just completed a Rinse or Hot Water cycle proceed to step 4 Lift the handle The brewing chamber will open towards you check to make sure there is no K Cup inserted Lower the handle to close the brewing chamber When closed completely the control panel will indicated READY All brew size icons will be displayed with your default size shown as a solid mug To choose a different size use the Y or A buttons Press Hot Water While the Hot Water cycle is in progress only the Hot Water button will be lit The control panel will display the words HOT WATER as well as the serving size you selected see figure 12 lt HOT WATER b j figure 12 Following the cycle your Brewer will automatically fill and heat in preparation for the next cycle After the heating cy
19. m with the arrow on the brewing chamber Cleaning the Funnel The Funnel can be removed from the K Cup Holder by pulling on it until it pops off see figure 27 The Funnel is top rack dishwasher safe To replace it just snap it back onto the K Cup Holder Assembly figure 27 8 Cleaning the Exit Needle The Exit Needle is located on the inside bottom of the K Cup Holder Assembly Should a clog arise due to coffee grinds it can be cleaned using a paper clip or similar tool Remove K Cup Holder as shown in figure 27 Insert the paper clip See figure 28 to loosen the clog and push it out CAUTION There are sharp needles that puncture the K Cup above and below To avoid risk of injury do not put your fingers in the K Cup Assembly Housing figure 28 Cleaning the Water Reservoir amp Lid Neither the reservoir lid nor the reservoir should be put into the dishwasher Clean them with a damp soapy non abrasive cloth and rinse thoroughly Do not dry the inside of the water reservoir with a cloth as lint may remain Caution Rinse the water reservoir thoroughly after cleaning to ensure that no cleaners or cleaning solutions remain in this area as they may contaminate the Brewer s water supply figure 29 19 De Scaling your Brewer Mineral content in water varies from place to place Depending on the mineral content of the water in your area calcium deposits or
20. ngredients are at their freshest Element 3 GRIND The grind of coffee and cocoa or the refinement of your tea leaves is critical for proper flavor extraction With the pre measured pre ground ingredients found in every K Cup you can rest easy knowing that it ll brew perfectly each and every time locking in maximum flavor and freshness Element 4 PROPORTION No matter which cup size you choose the Cuisinart Single Serve Brewing System working in conjunction with K Cup always produces the perfect cup every time When grinding your own coffee and using it in the included My K Cup remember to add the amount of ground coffee that corresponds to the number of ounces being brewed Features and Benefits KY 1 Charcoal Filter Holder 5 Drip Tray 1a Charcoal Water Filter 6 Drip Tray Base 2 Water Reservoir Lid 7 Removable K Cup Holder Removes for easy filing 8 Handle 3 Removable 80 oz Easy grip prevents slips Water Reservoir 9 Brewing Head Offers extra large capacity eliminating the need for frequent refills 4 Removable Drip Tray Plate Allows extra space for travel mugs 10 Brewing Chamber Holds My K Cup or the K Cup Holder 11 Housing 12 13 14 15 16 17 18 19 Control Panel Menu Button Up Button A Down Button Y Brew Button Rinse Button Hot Water Button My K Cup Compartment Conveniently stores My K Cup 20 21 22
21. ntil ADD WATER is displayed on the control panel and the reservoir lights will flash Let the Brewer stand for at least four hours while still on Rinse the water reservoir thoroughly and fill with fresh water Run another Hot Water cycle Discard contents of large mug Repeat hot water process until ADD WATER is displayed on the control panel and the reservoir lights will flash You may need to perform additional Hot Water cycles if you detect any residual vinegar taste Note If DE SCALE is still displayed on the control panel after completing the procedure repeat the de scaling procedure above 3 10 20 Troubleshooting Problem Brewer does not have Plug Brewer into an independent outlet PINS Make sure the Brewer is securely plugged in Plug into a different outlet Reset your home s circuit breaker Confirm the power has been turned on and the LCD is illuminated i o zd ie 2 Brewer will not brew Every once in a while an air bubble may get trapped in the water path Lift off the reservoir then put it back into place Turn off and unplug the brewer for 30 seconds or more When you plug the brewer back in be sure to turn the power back on lake sure the water reservoir is properly in place and perform a Rinse cycle After placing the K Cup in the K Cup Holder make sure the handle is pushed down securely and the LCD control panel reads READY The Y and A buttons Brew
22. ockwise to seal 6 Raise the handle and the brew chamber will open toward you 13 T 8 11 12 Remove the K Cup holder from the brewing chamber by pulling toward you If you would like store the K Cup holder in the My K Cup storage compartment Drop the assembled My K Cup into the brewing chamber No need to snap it into place See figure 15 Fas BK figure 15 CAUTION There are two sharp needles that puncture the K Cup one above and one below To avoid risk of injury do not put your fingers in the K Cup brewing chamber Follow Brewing instructions on page 10 10 Following brewing raise the handle and remove the My K Cup Use caution as the My K Cup will be hot Disassemble the My K Cup by turning the lid from the holder in a counter clockwise direction Remove the filter basket from the holder discard the grounds and rinse out the filter basket and holder Replace the K Cup holder ensuring the arrow on K Cup rim aligns with the arrow on the brewing chamber Gently push the K Cup holder to snap into place see figure 16 figure 16 Stopping the Brew Process If for any reason you need to stop brewing after the process has started press the power switch on the rear right side of the Brewer to turn the Brewer off The flow of coffee tea or hot cocoa will stop the heater will shut off and the blue lights illuminat
23. on Raise and lower the handle on the Brewer without inserting a K Cup When the control panel displays READY dispense 12 oz of hot water by selecting the 12 0z cup size and hot water Repeat this process two more times to completely replace the water in the inner tank 14 Programming Setting the Clock Setting the clock is optional When the clock is set the time will appear on the control panel Note You must set the clock if you plan on using the ONOFF TIME SET programming feature 1 Press the Menu button Programming options will appear on the control panel with CLOCK flashing The word OFF will appear at the top of the control panel to indicate that the clock is not set see figure 17 NEF SALSALIN He CLOCK lt MEAS lz Set Hours Set Minutes figure 17 Press or hold the W button to scroll through the hours until you have reached the appropriate hour Be sure the PM indicator is on if a PM time is desired Press or hold the A button to scroll through the minutes until you have reached the desired minutes When you have reached the correct time press the Menu button to set the time Continue pressing Menu to scroll through the remaining programming functions to exit the programming mode The correct time should now be displayed on top of the control panel see figure 18 15 Clock set in READY Mode EZ figure 18 Note Depending u
24. orized accessories and replacement parts This warranty expressly excludes any defects or damages caused by accessories replacement parts or repair service other than those authorized by Cuisinart This warranty does not cover any damage caused by accident misuse shipment or other than ordinary household use This warranty excludes all incidental or consequential damages Some states do not allow the exclusion or limitation of these damages so these exclusions may not apply to you You may also have other rights which vary from state to state Important If the nonconforming product is to be serviced by someone other than Cuisinart s Authorized Service Center please remind the servicer to call our Consumer Service Center at 1 800 726 0190 to ensure that the problem is properly diagnosed the product is serviced with the correct parts and to ensure that the product is still under warranty NOTES Cuisinart SAVOR THE GOOD LIFE T J Coffeemakers Food Rotisserie Blenders Cookware Slow Processors Cookers Cuisinart offers an extensive assortment of top quality products to make life in the kitchen easier than ever Try some of our other countertop appliances and cookware and Savor the Good Life www cuisinart com 2010 Cuisinart 150 Milford Road East Windsor NJ 08520 Any trademarks or service marks of third parties used herein are the trademarks or service marks of their respective owners Prin
25. pon the Brewer s current mode other icons will be displayed as well Note If power is interrupted to the Brewer the clock will need to be reset Follow the procedure above to reset the clock Programming On Off Features The Brewer provides three ways for you to enjoy gourmet coffee tea or hot cocoa on your own schedule It will take the Brewer approximately 3 2 minutes to warm up from room temperature 1 Leave it on all the time The Brewer can be left on all the time so that it is always ready to brew a fresh cup of gourmet coffee tea or hot cocoa To turn the Brewer off at any time simply press the power switch located on the right side of the Brewer Note Although the clock remains on if set you cannot brew a cup of coffee tea or hot cocoa if the brewer is off Press the power switch to restore power to the Brewer You will have to wait for the water to heat up before the Brewer is ready to brew 2 Set the Brewer to AUTO OFF This will automatically shut the Brewer off after a specified period of time from the last brew a Press the Menu button until AUTO OFF SET flashes see figure 19 AULT TET 7AVEPEPTTLU FEY Set Hours figure 19 b Press or hold the W button to advance one hour at a time up to 9 hours c After setting the desired AUTO OFF TIME press the Menu button to set the AUTO OFF TIME Continue pressing Menu to scroll through the remaining programming
26. ress down on the filter compartment and pull toward you to open Place the filter into the holder and snap it closed Be careful improper placement can tear the filter skin see figure 6 BREWING figure 5 5 Flush the filter by running fresh water through the hole in bottom of compartment for 10 seconds 6 Allow the filter to drain completely 7 Place the assembled water filter holder into the water reservoir pushing it down to fit into place see figure 7 Water Reservoir Lid a 4 Charcoal Water Filter Di i Water Reservoir zi ED is figure 7 Note We recommend changing the water filter every 60 days or after 60 uses and more often if you have hard water Replacement filters can be purchased in stores by calling Cuisinart Customer Service or at www cuisinart com Brewing 1 2 The control panel will display OPEN HEAD while in idle mode Place a cup or mug on the drip tray The drip tray can be removed to accommodate travel mugs Lift the handle The brewing chamber will open toward you Select a K Cup Portion Pack Note Do not remove the foil lid or puncture the K Cup Place a K Cup in the brewing chamber see figure 8 K Cup Portion Pack sn Sie figure 8 Caution There are two sharp needles that puncture the K Cup one above and one below To avoid risk of injury
27. scale may build up in your Brewer Though scale is non toxic it can hinder Brewer performance De scaling your Brewer will help maintain the heating element and other Brewer parts that come in contact with water For optimal performance de scale your Brewer every 3 to 6 months It is possible for calcium deposits to build up faster making it necessary to de scale more often This Brewer is equipped with sensors to detect when scale buildup is interfering with the performance of the Brewer When this is detected DE SCALE will be displayed on the control panel see figure 30 at which point you should promptly de scale However even if DE SCALE is not displayed it is still advisable that you de scale your Brewer regularly 1m m READYDE SCALE Yo wp DUP figure 30 Note Though the Brewer will continue to function even when DE SCALE is displayed not de scaling at that point could damage the Brewer If this occurs DE SCALE will begin to flash on the control panel to alert you to potential damage if you do not de scale immediately Follow these steps to de scale your unit 1 Empty the reservoir 2 Disable the AUTO OFF and OFF TIME features Making sure there is no K Cup in the brewing chamber fill the reservoir with 60 oz of undiluted white vinegar Place a large mug on the drip tray and run a Hot Water cycle Select the 12 oz brew size Discard contents of mug Repeat the hot water process u
28. ted in China Keurig the Cup and Star logo Keurig Brewed Quiet Brew Technology 10CE114545 and K Cup are trademarks or registered trademarks of Keurig Incorporated Covered by U S patents numbered 7 165 488 7 398 726 7 347 138 7 377 162 and 7 360 418 and other U S and foreign patents and patents pending IB 10074
29. uct registration However product registration does not eliminate the need for the consumer to maintain the original proof of purchase in order to obtain the warranty benefits In the event that you do not have proof of purchase date the purchase date for purposes of this warranty will be the date of manufacture CALIFORNIA RESIDENTS ONLY California law provides that for In Warranty Service California residents have the option of returning a nonconforming product A to the store where it was purchased or B to another retail store that sells Cuisinart Single Serve Brewing System products of the same type The retail store shall then according to its preference either repair the product refer the consumer to an independent repair facility replace the product or refund the purchase price less the amount directly attributable to the consumer s prior usage of the product If neither of the above two options results in the appropriate relief to the consumer the consumer may then take the product to an independent repair facility if service or repair can be economically accomplished Cuisinart and not the consumer will be responsible for the reasonable cost of such service repair replacement or refund for nonconforming products under warranty California residents may also according to their preference return nonconforming products directly to Cuisinart for repair or if necessary replacement by calling our Consumer Servic
30. uid from the K Cup 11 Caution There is very hot water in the K Cup chamber during the brew process To avoid risk of injury do not lift the handle or open the K Cup chamber during the brew process 8 Lift the handle then remove and dispose of the used K Cup Close the brewing head Caution K Cup will be hot Following the brew your Brewer will automatically fill and heat in preparation for the next brew Your Brewer will display NOT READY When water reaches default temperature OPEN HEAD will be displayed on the control panel and your unit will return to Idle mode and will be ready for your next brew Enjoy your cup of gourmet coffee tea or hot cocoa Hot Water Rinse Your Brewer is equipped to dispense hot water to make hot chocolate tea soup and more Your Brewer is also equipped with a Rinse cycle to flush out residual flavors The Rinse cycle will dispense about 4 oz of hot water Note We suggest to running the Rinse cycle before using hot water to flush out any residual coffee tea or hot cocoa flavor To Rinse 1 Place a cup or mug on the drip tray If you ve just completed a Rinse or Hot Water cycle proceed to step 4 Lift the handle The brewing chamber will open towards you check to make sure there is no K Cup inserted Lower the handle to close the brewing chamber When closed completely the control panel will indicated READY Press Rinse During the R
31. wer is interrupted to the Brewer you will need to re set the clock refer to page 15 Brewer shuts off or Make sure the Auto Off and the On Off time features have not been set To do this turns on automatically press the Menu button and scroll through the programming options OFF should be displayed for Auto Off timer and On Off If OFF is not displayed you must reset refer to page 15 The blue light in the This indicates the water level in the reservoir is low and water must be added refer water reservoir is to page 14 in order to brew a full cup flashing Coffee is too weak or Reduce the brew size for a stronger tasting cup of coffee refer to Programming watery Your Brew Size on page 18 Try an Extra Bold K Cup It has 30 more ground coffee in each portion pack WARRANTY Limited Three Year Warranty This warranty is available to consumers only You are a consumer if you own a Cuisinart Single Serve Brewing System that was purchased at retail for personal family or household use Except as otherwise required under applicable law this warranty is not available to retailers or other commercial purchasers or owners We warrant that your Cuisinart Single Serve Brewing System will be free of defects in materials and workmanship under normal home use for 3 years from the date of original purchase We recommend that you visit our website www cuisinart com for a fast efficient way to complete your prod
Download Pdf Manuals
Related Search