"user manual"
Contents
1. 117 X Description Turns on Geo fencing alarm When the tracker moves in out the preset scope it will send an SMS alarm to the authorized phone number for SOS Note 1 017 is for alarm when tracker moves out the preset scope 2 117 is for alarm when tracker moves in 3 X is the coordinates which include Lower left X Lower left Y Upper right X Upper right Y 4 Lower left X should be less than Upper right X 5 All longitudes and latitudes should be in ASCII format as follows Longitude DDDMM MMMM E W 4 places of decimal O is needed to be stuffed if no value available Latitude DDMM MMMM N S 4 places of decimal 0 is needed to be stuffed if no value available 6 Send W 006 00 to turn off Geo fence function Example W000000 017 11404 0000 E 2232 0010 N 11505 1234 E 2333 5678 N W000000 117 11404 0000 E 2232 0010 N 11505 1234 E 2333 5678 N Remarks 1 Only one alarm can be set in either In or Out 12 2 Only one alarm can be set in either Movement Alarm or Geo fence Alarm 12 Engine Cut Relay Connection Connect a replay as below picture shows White wire SOS button Yellow Relay P1 P2 Power for ignition Engine ignition loop Battery Calculate the correct VCC value according to relay s parameter to comply with the following requirements Output open drain sink voltage ineffective 45V max Output low voltage sink current effective 500mA2. When the tracker turns more than 90 degree a message will be sent back to the server 14 Initialization Command W 990 099 Description This is to make all settings except for the password back to factory default Note Turn on the device press the SOS button for five times continuously and the red LED will be on and then send within 120 seconds this SMS to the tracker is the ending character and is required in the text message Example W000000 990 099 15 Password Initialization Command W888888 999 666 Description This is to make the password back to factory default in case you forget your password Note Turn on the tracker press the SOS button for five times continuously and the red LED will be on and then send this SMS within 120 seconds to the tracker to make the password back to factory default 000000 Example W888888 999 666 For more details regarding SMS commands please go to Annex 1 Command List Annex 1 SMS Command List 14 Note js user s password and the default password is 000000 The tracker will only accept commands from a user with the correct password Commands with wrong password will be ignored Description sms command oe W 000 W000000 000 Remarks To get the current location of the tracker send this SMS or make a telephone call directly to the tracker and it will report its longitude and latitude by SMS with format as follows Latitud
3. max Normally two green wires are connected solidly P1 and P2 are Normal Close NC in the relay when the Output Out1 is open Out1 be Low voltage two green wires will disconnect the engine is then cut 12 1 Output Control Unlimited Command W 020 1 F Description Send this command to control the Output of VT300 Note F 0 to close the output open drain F 1 to open the output low voltage Example W000000 020 1 1 Once the relay is properly installed send this command to stop the engine 12 2 Output Control Limited Command W 120 F or W 220 F Description Send this command to control the Output of VT300 This command is only workable when the speed is below 10km h command 120 or 20km h command 220 and meantime GPS is available Note F 0 to close the output open drain F 1 to open the output low voltage lt 13 Example W000000 120 1 W000000 220 1 Once the relay is properly installed send this command to VT300 When its speed reaches at 10km h or 20km h it will stop the engine 13 Veer Report Command W 036 degree Description when the heading direction of the tracker changes over the preset degree a message with location data will be sent back to the server by GPRS This is to enhance the accuracy when the tracker make a direction change Note degree 0 to turn off this function degree 1 360 to set degree of direction change Example W000000 036 90
4. 37E Speed 2 6854Km h 2008 12 24 01 50 Example w000000 000 Track on Demand Reply with a Google link Command W 100 Description Send this command to the tracker and then you receive an SMS with an http link Click on the link then the location can be shown directly on Google Map on your mobile phone For example Note Only smart phones and PDA support this function Example W000000 100 Se ewe Text message g Text message T 149 1 4 123 0 y 1 349 Kn To Tracker From Tracker W000000 100 7 2 Track by Calling Make a missed call to the tracker and it will report its longitude and latitude by SMS with format as follows Latitude 22 32 36 63N Longitude 114 04 57 37E Speed 2 6854Km h 2008 12 24 01 50 7 3 Track by Preset I nterval Command W 002 XXX Description Set an interval for the tracker to continuously return its location by SMS Note 1 XXX is the interval in minute 2 If XXX 000 to turn off tracking by time Example W000000 002 030 The tracker will send location data back to your mobile phone every 30 minutes 7 4 Google Earth and Google Map Download Google Earth from http earth google com Start Google Earth For more information about Google Earth please refer to http earth google com or go to http maps google com in your Internet Explorer Input the latitude and longitude that you receive from the tracker by SMS and click the search button Google Earth or Go
5. 666 W888888 999 666 Remarks In case you forget your password turn on the tracker press the SOS button for five times continuously and the red LED will be on and then send this SMS within 120 seconds to the tracker to make the password back to factory default 000000 Annex 2 Troubleshooting Problem Unit will not turn on Possible Cause Resolution Wiring was not connected properly Check and make sure wiring connection is in order Battery needs charging Recharge battery Problem Unit will not respond to SMS Possible Cause Resolution GSM antenna was not installed properly Make VT300 connected to GSM network 19 GSM Network is slow Unit is sleeping Wrong password in your SMS or wrong SMS format The SIM in VT300 has run out of credit No SIM card SIM card has expired SIM has PIN code set SIM is warped or damaged Roaming not enabled Error connecting GSM antenna Problem SMS received starts with Last Possible Cause Unit does not have clear view of the sky VT300 is in an inner place Battery is low Error connecting GPS antenna Some GSM networks slow down during peak time or when they have equipment problems Cancel sleeping mode Write correct password or SMS format Replace or top up the SIM card Insert a working SIM card Check in phone that the SIM can send SMS message Check in phone that the SIM can send SMS message Rep
6. GPS Vehicle Tracker User Manual V6 1 VT300 Contents dl IP ROGIUICE OV CIVIC W e EEE EA E E EE dae ehedumeanees A E E E e denne keaton FOr COUR EE 3 VIOOL Rara e En dee eg gn EE 4 1 Hardware and E ge EE o BT At En tegeieeH We 4 4 Connecting and Rn Ce e Le WEE e Ee il Saa EEE E E E E E E TEE PE E EE T E E I E AE E 0 TINC ZONT erenn E EEEE AE E E ENEE EE EEA EEA EEE E AE ned E E PA OGM EE Talb AC leede EE EE Ded tee DY C Le EE Doe rack ee 7 4 Google Earth and Google E MEET 7 5 Track by GPRS between Server and Tracker cece cece eee ee ee eeeeeeeeee ee ee eee eeneeeenees J od CU MRICS OPR UD E K Sl PIN WE En e FOVE EE 7 5 4 Set DNS Server IP optional J29 EMDE GPRS TW ACA BEE EE E Ee e Gs CEET eege EE D LOW Bauer ET MEET OSa Ee EE E A EE T EE E E ET E E T A EE ENE E E E E EE 11 Movement Geo fence EE LLIT Oe ment Alari erreien errr eenn AEE EE EE e E rE LLZ Ee NCE A Miane EE Ten te e tu e E 12 1 Output Control UNIMItTEd EE 12 2 Q tpu ut Control LIMILEU J eebe EE Eben LN Or RODO EE TA WIA ZOOM EE 15 Password Re TE gd e EE Animex L 9M5 e eo un Le EE niet 2 TOUDICSROOHN O EE 1 Product Overview VT300 is a GPS GSM GPRS tracking device specially developed and designed for vehicle real time tracking and fleet management With superior GPS and GPRS modules VT300 has good sensitivity and stable performance It can get accurate GPS fix even in remote
7. Make a missed phone call the VT300 using a mobile phone to check if the calling can go through and the VT300 replies with an SMS indicating longitude latitude speed and date 5 Change Password Command W 001 4 Description Change user s password Note 1 jis user s password and the default password is 000000 The tracker will only accept commands from a user with the correct password Commands with wrong password will be ignored 2 HH F is the new password Password should be 6 digits Example W000000 001 123456 W123456 001 999999 6 Time Zone Command W 032 T Description Correct time into your local time Note 1 Default time of the tracker is GMT 2 This correction is applied to location reports by SMS and SMS alarms T 0 to turn off this function T 1 65535 to set time difference in minute to GMT For those ahead of GMT just input the time difference in minute directly For example GMT 8 W000000 032 480 is required for those behind GMT For example WO000000 032 120 Example W000000 032 480 W000000 032 120 7 Track 7 1 Track by SMS Track on Demand Reply with longitude latitude speed and date Command W 000 Description Get the current location of the tracker send this SMS or make a telephone call directly to the tracker and it will report its longitude and latitude by SMS with format as follows Latitude 22 32 36 63N Longitude 114 04 57
8. X 01 Level XX 02 Level II is the ending character Here is some explanation for the sleep mode First assume that the GPS acquisition time is ONE minute 1 In Level The GPS module will be working for the first three minutes i e 3 times of acquisition time and then shut down for ONE minute i e equivalent to acquisition time and then work again for another three minutes 2 In Level Il The GPS module will be working for the first two minutes i e twice of acquisition time and then shut down for ONE minute i e equivalent to acquisition time and then work again for another two minutes Werters 026 X W000000 026 10 Remarks to set power down mode when the tracker is inactive for a period of time In Power Down mode GPS stops working and GSM enters sleep and stop sending out message until it is activated by message incoming calls or triggered by buttons XX 00 to turn off this function XX 01 99 to turn on Power Down after a specified period of being inactive It is in unit of minute In this example the tracker will enter power down mode after it is inactive for 10 minutes UU E KR W000000 032 480 W000000 032 120 Remarks Default time of the cracker is GMT you can use this comment to correct it to your local time This command is for SMS tracking only T O to turn off this function T 1 65535 to set time difference in minute to GMT For those ahead of GMT just input the time difference in min
9. available Latitude DDMM MMMM N S 4 places of decimal O is needed to be stuffed if no value available Only one alarm can be set in either Movement Alarm or Geo fence Alarm Send W 006 00 to turn off Geo fence function W 008 ABCDEFGHI W000000 008 1011100011 Remarks A 0 turn off the function of sending SMS location report after a phone call is made to the tracker A 1 turn on the function of sending SMS location report after a phone call is made to the tracker B 0 location data of NMEA 0183 GPRMC will be interpreted into normal text for easy reading For example Longitude 114 degree 04 minute 57 74 second Latitude 22 degree 32 minute 40 05 second B 1 location data complies with NMEA 0183 GPRMC protocol For example GPRMC 161509 000 A 2232 5485 N 11404 6887 E 0 3 153 7 290709 03 C 0 turn off the function to automatically hang up an incoming call C 1 turn on the function to automatically hang up an incoming call after 4 5 rings D 0 turn off the function of sending an SMS when the tracker is turned on D 1 turn on the function of sending an SMS to the authorized phone number for SOS when the tracker is turned on E defaulted as 1 the tracker shuts down automatically when the power voltage is lower than 3V F 0 turn off the SMS alarm when the tracker enters GPS blind area F 1 turn on the SMS alarm when the tracker enters GPS blind area SMS is to be sent to the authorized phone num
10. ber for 505 G 0 all LEDs work normally G 1 all LEDs stop flashing when the tracker is working 16 H reserved and defaulted as 0 1 0 turn off the function of sending SMS alarm when the extra power of the tracker is cut l 1 turn on the function of sending an SMS alarm to the authorized phone number for SOS when the extra power of the tracker is cut J reserved and defaulted as 1 is the ending character ABCDEFGHI defaulted as 1000100001 Presetting by SMS for GPRS tracking Ensure that your SIM card supports GPRS connection prior to setting Werett 010 1D W000000 010 00001 Remarks to set a digital GPRS ID for the tracker GPRS ID must not over 14 digits W O11 APN Username W000000 011 CMNET abcd 6688 Password W000000 011 CMNET Remarks If no APN username and password are required just input APN only APN defaulted as CMNET APN username password should not over 39 characters Vyrete es O12 1F Port W000000 012 220 121 7 89 8500 W000000 012 www abcd net 8500 Remarks IP is your server s IP or the domain name Port 1 65534 W 009 DNS Server IP W000000 009 220 23 4 90 Remarks In case the domain name you set by the last command W 012 1P Port doesn t work which means your server IP is not properly set You can first use this command to set DNS Server IP please check with your DNS server provider for the DNS Server IP and then red
11. default 4 lt 3 6V 5 lt 3 7V WFttt 005 XX W000000 005 08 Remarks When the tracker speeds higher than the preset value it will send an SMS to the authorized phone number for SOS XX is the preset value of speed and in 2 digits 00 to turn off this function 01 20 unit 10Km h In this example when the tracker s speed is over 80km h an SMS alarm will be sent out 15 Werkt 006 4 W000000 006 06 Remarks When the tracker moves out of a preset square scope it will send an SMS alarm to the authorized phone number for 505 XX is the preset distance to the tracker s original place 00 to turn off this function 01 30m 02 50m 03 100m 04 200m 05 300m 06 500m 07 1000m 08 2000m Wtr 017X W000000 017 11404 0000 E 2232 0010 N 11505 12 Wen ee 117X 34 E 2333 5678 N W000000 117 11404 0000 E 2232 0010 N 11505 12 34 E 2333 5678 N Remarks 017 is for alarm when tracker moves out the preset scope 117 is for alarm when tracker moves in When the tracker moves in or out it will send an SMS alarm to the authorized phone number for SOS X is the coordinates which include Lower left X Lower left Y Upper right X Upper right Y For example 11404 0000 E 2232 0010 N 11505 1234 E 2333 5678 N Note 1 Lower left X should be less than Upper right X 2 All longitudes and latitudes should be in ASCII format as follows Longitude DDDMM MMMM E W 4 places of decimal 0 is needed to be stuffed if no value
12. e 22 32 36 63N Longitude 114 04 57 37E Speed 2 6854Km h 2008 12 24 01 50 EE W000000 100 Remarks Send this command to the tracker and then you receive an SMS with an http link Click on the link then the location can be shown directly on Google Map on your mobile phone For example http maps google com maps f q amp Ghl en amp q 22 540103 114 082329Gie UTF8 amp z 16 amp iwloc addr amp om 1 Note Only smart phones and PDA support this function WH COOL W000000 001 123456 Reine SE To change user s password is the new password Password should be 6 digits Wr 002 XXX W000000 002 030 een To set interval for automatic timed report XXX is the interval in minute If XXX 000 to turn off tracking by time In this example the tracker will send location data back to your mobile phone every 30 minutes Were 003 61 E W000000 003 1 1 88888888 oe To authorize phone numbers for the SOS button input for receiving location reports and SMS alarms F 0 to turn off this function default F 1 to turn on the function of sending SMS reports alarms to the authorized phone number T Preset phone number Max 16 digits Werte O04 x W000000 004 2 Remarks When the tracker s voltage is lower than the preset value it will send an SMS alarm to the authorized phone number for SOS X is the preset value of voltage 0 to turn off this function 1 lt 3 3V 2 lt 3 4V 3 lt 3 5V
13. er provider for the DNS Server IP and then redo the command W 012 1P Port Example W000000 009 220 23 4 90 7 5 5 Enable GPRS Tracking Command W 013 X Description Enable GPRS tracking function Note X 0 to turn off GPRS tracking default X 1 to enable GPRS tracking via TCP X 2 to enable GPRS tracking via UDP Example W000000 013 1 7 5 6 Set GPRS Interval Command W 014 XXXXX Description Set time interval for sending GPRS packets Note XXXXX should be in five digits and in unit of 10 seconds XXXXX 00000 to turn off this function XXXXX 00001 65535 time interval for sending GPRS packet and in unit of 10 seconds In this example the tracker will send every 600 seconds 10 minutes Example W000000 014 00060 The tracker will send every 600 seconds 10 minutes 10 For more information regarding GPRS tracking please refer to lt GPRS Communication Protocol gt 8 Authorization Command W 003 F 1 T Description Authorize phone numbers for the SOS button for receiving location reports and SMS alarms Note F 0 to turn off this function default F 1 Sends SMS to the authorized phone number T Preset phone number Max 16 digits Example W000000 003 1 1 88888888 SOS Button Connection Connect the SOS button and wires as below picture shows Input White SOS Button Note input voltage to Input must not over 45V After above authorization is complete once the SOS i
14. l parts are included in the packaging box 4 4 1 Ensure that your VT300 has a working SIM installed Check that the SIM has not run out of credit test the SIM in a phone to make sure it can send and receive SMS Check that the SIM Lock code is turned off If you require the function of sending an SMS location report to the authorized phone number when it makes a call to the VT300 please make sure the SIM installed Supports displaying caller ID Before inserting SIM card cut off the power for VT300 Install SIM Card Unscrew and remove the front cover of VT300 Insert the SIM card by sliding it into the card slot with the chip module facing to the connectors on PCB Put back the front cover and screw it up 4 4 2 Antenna Connection Connect the GSM Antenna to VT300 Connect the GPS Antenna to VT300 GPS antenna Is used to receive satellite signals in the sky It should be fixed to face the sky and should not be covered or shielded by any objects containing metal such as the metallic windshield 4 4 3 Find a suitable place inside the car for installing VT300 Wiring connections must be firm and reliable and the joints should be wrapped with insulating tape tightly The unused electrical wire should be properly insulated Check if all wirings have been connected correctly and then connect the AVL unit to the motor power Check that the Red LED Battery is flashing 1 second on and 2 seconds off
15. lace SIM card if needed Remove PIN code by inserting SIM in you phone and deleting the code Inspect SIM clean the contacts If re inserting does not help try another to see if it will work If you are in a different country your SIM account must have roaming enabled Make sure the GSM antenna is connected to the GSM interface Resolution Move the antenna of the unit to a location where the sky is visible Wait for the target to come out Recharge the unit and the GPS will start working Make sure the GPS antenna is connected to the GPS interface Problem Unit Fails to Connect to Server via GPRS Possible Cause SIM card in VT300 does not support GPRS function GPRS function of VT300 is turned off Incorrect IP address or PORT GSM signal is weak Resolution Enable SIM card GPRS function Turn on GPRS function of VT300 Get the right IP address and PORT and reset to VT300 Move the unit to a location with good GSM reception 90
16. o the command W 012 1P Port Were O13 Xk W000000 013 1 Remarks X 0 to turn off GPRS tracking default X 1 to enable GPRS tracking via TCP X 2 to enable GPRS tracking via UDP W O14 XXXXX W000000 014 00060 Remarks to set time interval for sending GPRS packets XXXXX should be in five digits and in unit of 10 seconds XXXXX 00000 to turn off this function XXXXX 00001 65535 time interval for sending GPRS packet and in unit of 10 seconds In this example the tracker will send every 600 seconds 10 minutes W 036 degree W000000 036 90 poe when the heading direction of the tracker changes over the preset degree a message with location data will be sent back to the server by GPRS degree 0 to turn off this function degree 1 360 to set degree of direction change Werte 020 06 W000000 020 1 1 F 0 to close the output open drain Remarks 1 to open the output low voltage For example if you have connected Output1 with a relay you can send WO00000 020 1 1 to stop the engine EE W000000 120 1 Werte ee 220 7 W000000 220 1 Remarks This function is achievable only when the speed is below 10km h command 120 or 20km h command 220 and meantime GPS is available F 0 to close the output open drain 1 to open the output low voltage W 021 XX W000000 021 02 Remarks this setting is for power saving XX 00 turn off sleep mode X
17. ogle Maps will display the location for you Example When you receive Latitude 22 32 40 05N Longitude 114 04 57 74E Type as the following picture shows Note you should input the latitude and longitude as 22 32 40 05N 114 04 57 74E Web Images Videos Maps News Shopping Gmail more e Google maps zouenen SOS S Find businesses addresses and places of interest Learn more Find Businesses Directions e g Reservoir Rd Clayville NY 2232 40 05N 1140457 74E e Q Get Directions My Maps d And then you can find the location of your tracker WS Google Gank aad Fis Pai we ron Asd Help File Edt View Favortes Took Help Gen Ass x Soach LI J Pages Teen ob Be E SS j a Ge evorhes 249 22 32 AROS 114 08 37 74E Google Maps yt Ye aes Devine e mages cam Maps Heen Shoscing Gmail mas Sigo Hag Google M DS 2232 4005N 114 os 57 D Basch Mag Som sence ossy Sp Mirties P Ciria n j F tu a RE r n Wi d 4 reer jja it E e A ON h Get Directeores Me Mam H 4 z 1 d See Lt A j e Stergtere A More 3 Li 11242 Zhenhua Rd i a 9 r BHE Senchen Geangiong Cins nal 3 amin Aer gt a e z Explore gp 2 e Photis po ug Diest a endag Re sou B SL LL Sak ec ei 2 Larran S d e Be e aera g Wees s Sam eer k Hurerere dan o uais 5s f Taita e S S SEAE A a ed e Drog vers eas D E j 3 g iia as me e p a g D anji re
18. places VT300 has the following functions and features SMS and GPRS TCP UDP Communication Track on Demand Show Location Directly on Mobile Phone Track by Time Interval SOS Panic Button Movement Alarm Geo fencing Control Low Battery Alarm Speeding Alarm GPS Blind Area Alarm in out Power cut Alarm O OO OO OO OO OO O Engine Cut Stop Engine 2 For Your Safety Read these simple guidelines Not following them may be dangerous or illegal Proper Connection When connecting with other device read carefully its manual so as to carry out correct installation Do not connect it to other incompatible devices Qualified Accessories Use original parts qualified batteries and peripheral equipments to avoid damage to VT300 Safe Driving Drivers should not operate this product while driving Qualified Service Only qualified personnel can install or repair VT300 Water Resistance VT300 is not water resistant Keep it dry Install it inside the vehicle Confidential Phone Number For safety reason do not tell other people the mobile phone number of your VT300 without taking precautions of security settings 3 VT300 Characteristics Items Specification Power Supply Backup Battery Normal power consumption Dimension Installation Dimension Weight Operating temperature Humidity Frequency GPS Chipset GPS Sensitivity GPS Frequency C A Code Channels Position Accuracy Velocity Accuracy Time Accuracy Default da
19. s pressed an SOS SMS SOS Alarm will be sent to the preauthorized phone number and then a message with longitude and latitude to follow 9 Low Battery Alarm Command W 004 X Description When the tracker s voltage is lower than the preset value it will send an SMS alarm to the authorized phone number for SOS Note X is the preset value of voltage 0 to turn off this function 1 lt 3 3V 2 lt 3 4V 3 lt 3 5V default 4 lt 3 6V ES lt 3 Example W000000 004 2 10 Speeding Alarm Command W 005 XX Description Turns on speeding alarm When the tracker speeds higher than the preset value it will send an SMS to the phone number for SOS Note XX is the preset value of speed and in 2 digits 00 to turn off this function 11 01 20 unit 10Km h Example W000000 005 08 When the tracker s speed is over 80km h an SMS alarm will be sent out 11 Movement Geo fence 11 1 Movement Alarm Command W 006 XX Description When the tracker moves out of a preset square scope it will send an SMS alarm to the authorized phone number for SOS Note XX is the preset distance to the tracker s original place 00 to turn off this function 01 30m 02 50m 03 100m 04 200m 05 300m 06 500m 07 1000m 08 2000m Example W000000 006 06 When tracker moves out of this square scope it will send out an SMS alarm 11 2 Geo fence Alarm Command W 017 X or W
20. side as factory default When the wires are plugged in VT300 will be switched on automatically as the two yellow cables SW1 and SW2 are connected together SOS Button SOS button is connected with the wires Press it to send SOS alarm to the preauthorized phone number Mini USB Used for firmware update and configuration on PC USB to Serial Adaptor is required for firmware update and configuration by computer SIM Card To insert SIM card here GSM Antenna Connector for GSM antenna GPS Antenna Connector for GPS antenna Screw Holes There are 4 screw holes on the tracker 2 along either side that act as fixing points to the vehicle PINs Connector PIN Color Function DC IN Red DC In power input Input voltage 9V 36V 12V suggested GND Black GND IN White Input Negative triggering Low voltage OV when effective and open drain or HIGH voltage gt 1V and max 45V when ineffective OUT1 Blue Output Low voltage OV when effective and open drain when ineffective Output open drain sink voltage ineffective 45V max Output LOW voltage sink current effective 500mMA max SUN Yellow SW1 connected with power switch Note if you need to connect it to other switch make sure the voltage should not over 4 5V SW2 Yellow SW2 connected with power switch Note if you need to connect it to other switch make sure the voltage should not over 4 5V 4 4 Connecting and Installation Read this manual before using your VT300 and check if al
21. sres oars g wera agit stan eum i F De E hie GOaeaegpbe inia DS Os Ep e 5 SR ta z af EODH En rs eo en Sa Dore meme Protected Mode On ar 41008 Or you can use local map software on PDA or car navigation device to input the coordinates 7 5 Track by GPRS between Server and Tracker 7 5 1 Set Tracker s GPRS ID Command W 010 ID Description Sets a digital GPRS ID for the tracker Note GPRS ID must not over 14 digits Example W000000 010 00001 7 5 2 Set APN Command W 011 APN Username Password Description Set APN details for the tracker Note 1 APN username and password are optional If no APN username and password are required just input APN 9 only 2 APN defaulted as CMNET 3 APN username password should not over 39 characters Example W000000 011 CMNET abcd 6688 W000000 011 CMNET 7 5 3 Set IP and Port Command W 012 1P Port Description Set IP and Port for tracker for GPRS communication Note 1 IP is your server s IP or the domain name 2 Port 1 65534 Example W000000 012 220 121 7 89 8500 W000000 012 www abcd net 8500 7 5 4 Set DNS Server IP optional Command W 009 DNS Server IP Description In case the domain name you set by the last command W 012 1P Port doesn t work which means your server IP is not properly set You can first use this command to set DNS Server IP please check with your DNS serv
22. tum Reacquisition Hot start Warm start Cold start Altitude Limit Velocity Limit LED Button Interface 9V 36V 1 5A 850mAh 85mA h 115mm x 60mm x 21mm 115mm x 79mm x 21mm 140g 20 to 55 C 5 to 95 Non condensing GSM 900 1800 1900Mhz or GSM 850 900 1800 1900Mhz optional latest GPS SIRF Star III chipset 158Db L1 1575 42 MHz 1 023 MHz chip rate 20 channel all in view tracking 10 meters 2D RMS 0 1 m s 1 us synchronized to GPS time WGS 84 0 1 sec average 1 sec average 38 sec average 42 sec average 18 000 meters 60 000 feet max 515 meters second 1000 knots max 1 LED light to show working status One SOS button One input and one output 4 Getting Started This section will describe how to set up your VT300 4 1 Hardware and Accessories VT300 is supplied in a box which includes PA gt se Wires with SOS Button VT300 with Battery GPS Antenna GSM Antenna Screws CD 4 2 View Front View Side View Back View 4 3 Functional Parts GSM Antenna GPS Antenna GSM Antenna GPS Antenna Screw Hole Screw Hole SIM Card Holder Battery LED Mini USB Battery LED Screw Hole Screw Hole ii PINs Connector PINs Connector SOS Button Battery LED Off Power is off or charging is complete Flashing every 0 1 second Low power On Charging Flashing 1 second on and 2 seconds off Working Power On Off Button To turn on off VT300 Note The switch is on off
23. ute directly For example GMT 8 W000000 032 480 is required for those behind GMT For example W000000 032 120 e ME Veer es E ECTS W000000 033 1 help Remarks this command is to set initial characters for SOS message when the SOS button input is pressed Char is the character in SOS message and max 32 characters and defaulted as SOS Alarm Wetter 502 Data W000000 502 86 Remarks be advised caution in this setting Normally your country code for example in China it is 86 will be automatically added and displayed prior to a phone number when sending SMS In this case you don t have to do this setting If the country code is not added you are required to input the country code for example 86 to enable the tracker can send out SMS to your mobile phone Data max 10 digits Wet 600 W000000 600 Remarks to get the version and serial number of tracker s firmware Wr 601 w000000 601 Remarks to get IMEI of the tracker WH OOLH W000000 901 Remarks to reboot the GSM module of the tracker WH K 902 W000000 902 Remarks to reboot the GPS module of the tracker W 990 099 W000000 990 099 Remarks Turn on the device press the SOS button for five times continuously and the red LED will be on and then send within 120 seconds this SMS to the tracker to make all settings except for the password back to factory default is the ending character W888888 999
Download Pdf Manuals
Related Search