USER MANUAL
Contents
1. e Forward Brake Reverse e Sensored Design e Multi Protection System e Plug in and Drive e Limited Lifetime Warranty Please read the following instructions to ensure that your NOSRAM EVIL BRUSHLESS POWER REVERSE speed control always works up to your full satisfaction Please read and understand these instructions completely before you use this product With opera ting this product you accept the NOSRAM warranty terms EVIL Brushless Reverse EVIL Brushless Power Reverse 90400 90450 Brushless Brushed yes yes Brushless Brushed Adaptation Automatic Automatic Forward Brake Reverse yes yes Case Size 41 0 x 41 8mm 41 0 x 41 8mm Weight excl wires 62g Voltage Input 4 8 8 4V 4 8 8 4V Typical Voltage Drop Brushless 20A 0 160V 20A 0 072V Rated Current Brushless 120A phase 150A phase Compatible winding styles Star Rec Motor Limit for Star winds Brushless over 12 5 turns over 8 9 turns Typical Voltage Drop Brushed 20A 0 120V 20A 0 054V Rec Motor Limit Brushed over 10 turns over 7 turns Rated Current Brushed 120A 150A SmartCell System NiMH LiPo automatic adaptation yes yes 4 5 and 5 cell optimised yes yes B E C 3 0V High Frequency yes yes Sensored Brushless System yes yes Fail Safe System yes yes Waterproof yes yes Multi Protection System yes yes Standard Tamiya Style Connectors yes Set Up Procedure Automatic Automatic lt o1 ee oD cD oO no wn fos Transistors rating at 22. Let everything cool down for a few minutes If the speed control switches off frequently either the motor used is too strong the motor pinion is too big or you are using full brake too often You can improve this if you make additional cooling slots in the body D i os Oro pew IIN FO NG All products from NOSRAM are manufactured according to the highest quality standards NOSRAM guarantees this product to be free from defects in materials or workmanship for 90 days non european countris only from the original date of purchase verified by sales receipt This limited warranty doesn t cover defects which are a result of normal wear misuse or improper maintenance This applies among other things on Because we don t have control over the installation or use of this product we can t accept any liability for any damages resulting from using this product Therefore using this product is at owner s risk Our limited warranty liability shall be limited to repairing the unit to our original specifications In no case shall our liability exceed the original cost of the unit By installing or operating this product the user accepts all resulting liability e Cut off original power plug or not using reverse polarity protected plugs Receiver wire and or switch wire damaged Mechanical damage of the case Mechanical damage of electronical components PCB Soldered on the PCB except on external solder tabs With Limited Lifetime Warranty products the
3. warranty terms on the Limited Lifetime Warranty card do also Connected speed control with reversed polarity apply The specifications like weight size and others should be seen as guide values Due to ongoing technical im provements which are done in the interest of the product NOSRAM does not take any responsibility for the accuracy of these specs To eliminate all other possibilities or improper handling first check all other components and the trouble shoo ting guide if available before you send in this product for repair or warranty Products sent in for repair that operate perfect have to be charged with a service fee NOSRAM Distributor Service e Package your product carefully and include sales receipt and detailed description of malfunction By sending in this product you assign NOSRAM to repair the product if it is no warranty or Limited Lifetime e Send parcel to your national NOSRAM distributor Warranty case The original sales receipt including date of purchase needs to be included Otherwise no war e Distributor repairs or exchanges the product ranty can be granted For quick repair and return service add your address and detailed description of the e Shipment back to you usually by COD cash on delivery but this is subject to your national NOSRAM malfunction distributor s general policy
4. 5 C junction temperature Specifications subject to change without notice measured at 7 2V The NOSRAM EVIL BRUSHLESS POWER REVERSE speed control comes pre wired using common Tamiya JST style battery and motor connectors Be very careful with the correct wire sequence colors since an incorrect connection may damage the speed control e Mount the speedo using the supplied thick black doubled sided tape e Connect the Receiver wire of the speed control with the receiver position Channel 2 Caution Be careful with the correct polarity of the receiver wire CONNECTION OF A BRUSHLESS MOTOR e Blue power wire gt Connect to motor A e Yellow power wire gt Connect to motor B e Orange power wire gt Connect to motor C e Connect the hall sensor cable to the speed control and the motor Hall Sensor Wire CONNECTION OF A BRUSHED MOTOR e Blue Yellow power wire Connect to motor Minus e Orange power wire gt Connect to motor Plus NOSRAM Tip Use the supplied adapter wires Together to minus e Doublecheck all connections before connecting the speed control to a battery CAUTION If battery is connected with reversed polarity it will destroy your speed control e Red power wire gt Connect to battery Plus e Black power wire gt Connect to battery Minus e You can now switch on the speed control with the On Off Switch e The speed control is now ready to be set up please se
5. RA00229 brushless brushed automatic adaptation 100 automatic 100 waterproof fail safe s P t D F o R c E PSI REVERSE 90400 90450 for distributor address see packaging Wwiww nosram com On Off Switch erea a i gt BAT Black BAT Red eee MOT C Orange MOT B Yellow MOT A Blue Receiver Hall Sensor Connecting Wire Connector RECEIVER CONNECTING WIRE This NOSRAM speed control is equipped with an NOSRAM Multicon receiver wire As supplied it will easily fit in all ordinary receivers HALL SENSOR WIRE This bi directional multipole wire which comes with the motor and NOT the speed control connects the speed control and the motor Do not alter or modify this cable There are replaceable optional hall sensor wires available 92510 20cm e 92520 10cm POWER WIRES The NOSRAM EVIL BRUSHLESS POWER REVERSE speed control comes pre wired using common Tamiya JST style battery and motor connectors Together with a NOSRAM DRAGON BRUSHLESS SPORTS MO DIFIED motor 90510 90540 and a pre assembeled battery pack from NOSRAMSs selection of battery packs the speed control can be used instantly without the need of a solder iron Additionally included with this speed control are a set of adapter wires to connect the NOSRAM EVIL BRUSHLESS POWER REVERSE with a brushed motor please see section 3 Installation for further reference You can also solder the power wires of the speed co
6. an check the current mode setting by switching on the speed control while the transmitter is also switched on The initial flashing of the LED tells you which mode is currently activated e The LED flashes once followed by a short break and then stays on continuously gt LiPo NiMH Automatic Mode is active e The LED flashes twice followed by a short break and then stays on continuously gt 4 7cell NIMH Racing Mode is active Toggle SmartCell mode 1 Pull out the receiver wire from the receiver 2 Turn on the speed control with the battery connected 3 The LED flashes and indicates the current mode See above for further reference 4 After approx 5 sec the speed control automatically switches the mode This will be indicated by the LED flashing again and indicating the new mode 5 Turn off the speed control The new mode setting is now stored 6 Re connect the receiver wire of the speed control with the receiver EXPLANATION f no remark cause can be either with brushless or brushed motor If BM is indicated cause only relating to brushed motor REMEDY S Overload protection activated BM Motor brushes stuck Plug speed control in with correct polarity Servo is working no motor function Speed control plugged in incorrectly Speed control defective No servo and no motor function Speed control plugged in incorrectly Crystal defective Replace components one by one Receiver defective Transmitter defe
7. ctive Send in product for repair Connect motor correctly Use smaller motor pinion shorter gear ratio Speed control defective Motor runs in reverse when accelera BM Motor connected incorrectly ting forward on the transmitter Insufficient performance Motor pinion too big or gear ratio too long very low battery voltage Ea poor wake power topspeedor ersten settings changed after set up Waterproof Due to latest production technologies and use of HighTech materials it was possible to make these speed controls fully waterproof This material also makes the speed controls more shock resistant then other similar products It s no longer needed to seal your speed control when you are driving in the rain snow Speed control overheats or switches But please make sure you still seal your other electronic components receiver servo and motor since off frequently too high specifications of the speed control these are normally not waterproof and will get damaged due to the water Fail Safe System Digital protection against radio interference The guardian angel The safety electronic can detect reception of a false or incomplete radio signal e g due to a low transmitter battery or environmental radio interference which reach the model or if the model is out of the transmitter range Motor never stops runs at constant For protection against damage the speed control switches to the neutral position and the model comes slow s
8. e section 6 Speed Control Set up for further reference After wiring up the speed control it is ready to operate No setup is required The speed control learns the neutral full speed forward and full speed reverse points while the car is running Please note Before you plug in the drive battery set the transmitter to neutral position and then start the model in the forward direction If you have made a mistake so far don t worry Switch off the speed control for about 10 seconds and start over again After the run first switch off the speed control unplug the battery and then switch off the transmitter When you start again first switch on the transmitter then plug in the battery and switch on the speed control CHECKING THE FUNCTIONS Check the LED s when moving your throttle stick and you will see if everything is setup correctly FUNCTION LED ull brake reverse Automatic Brushless Brushed Adaptation The NOSRAM exclusive Automatic Brush less Brushed Adaptation detects the connected motor type during turn on initialisation and adjusts the correct brushless or brushed operation automatically No adjustments required by yourself apart from the correct connection of each motor type don t forget the hall sensor wire for brushless NOSRAM Automatic Setup Due to the NOSRAM exclusive Automatic Setup Technology there is no need for a manual setup of the speed control by pushbuttons or potentiometers Al
9. l you need to do is simply plug in the speed control and you re ready to go The speed control learns the neutral full speed forward and full speed reverse point of the radio system while the car is running This way the speed con trol has the optimized setup for every run automaticly Incorrect setups are a thing of the past with the NOSRAM EVIL BRUSHLESS POWER REVERSE speed controls SmartCell System Ready for the next battery technology LiPo batteries NOSRAM s exclusive and clever SmartCell System ensures that LiPo batteries can be used safely without accidentially deep discharging of the cells The motor function will be shut off and the LED will flash if the system recognises The NOSRAM EVIL BRUSHLESS POWER REVERSE speed control features NOSRAMs excluxive SmartCell System You can choose between 2 modes e LiPo NiIMH Automatic Mode e 4 7cell NIMH Racing Mode The works default setting of the speed control is LiPo NiMH Automatic mode When using the LiPo NiMH Automatic Mode the speed control will switch off the drive function as soon as the battery voltage falls under a value which is harmful for LiPo batteries Thus protecting your LiPo battery against deep discharging If you are using your speedo with LiPo batteries we strongly recommend to always use the LiPo NiMH Automatic Mode When using the 4 cell Racing Mode the drive function will not be switched off Displaying the current mode during switch on You c
10. ntrol directly to the motor if you do not want to use the supplied plugs Nevertheless some soldering skills are still required However please note that your warran ty may void if you cut off the plugs Therefore we recommend using the original power wires and plugs Mount the speedo using the supplied thick black doubled sided tape Position the speed control where it is protected in the event of a crash Install the speed control so that you have easy access to the connector and buttons Make sure there is enough clearance about 3cm between the speed control power wires antenna and receiver Avoid any direct contact between power components the receiver or the antenna This can cause interference If interference occurs position the components at a different place in the model The aerial should be run vertically up and away from the receiver Avoid contact with any parts made of carbon fibre or metal If the aerial is too long don t coil up the excess length It is better to cut it down to a length of about 35 cm See also the instructions supplied with your radio control system Make sure there are enough cooling slits in the body This will increase the performance and life of all the electronic components HEATSINK To achieve best perfomance even under extreme conditions the heatsink has been directly mounted to the speed control This ensures the best possible heat transfer away from the speed control Caution Never attempt to
11. peed PERR ieni kai NOSRAM tip The model will remain in a standstill even if you connect the drive battery to the speed control first and then switch on the transmitter Provides perfect protection against mistakes commonly Radio interference made by beginners Receiver or antenna too close to power wires See Installation Tips and Installation motor battery or speed control Receiver aerial too short or coiled up Receiver defective too sensitive Replace components one by one Transmitter defective transmitter output power Only use original manufacturers crystals too low servo problem Poor battery connection Check plugs and connecting wires Transmitter batteries empty Replace recharge transmitter batteries Transmitter antenna too short Pull out antenna to full length Speed control looses settings Receiver problem especially with some 2 4GHz Use a power capacitor on the receiver systems Sensored Brushless Technology The sensors allow the perfect knowledge of the brushless motor s magnet position This results in perfect motor control at high and low RPM s as well as perfect brake control Multi Protection System 3 way protection The perfect protection against short cir cuits motor overload and overheating of the speed control and of the motor If your speed control or motor faces overload the motor function will be shut off for protection and the LED will flash although the steering function is maintained
12. remove the heatsink Because of the physical principles of brushless technology the speed controls do get a little hotter then brushed systems Therefore it is required to let the speed control cool down completely after every run When running in extreme conditions high ambient temperature low turn motors high gear ratios etc we recommend using NOSRAM s brushless cooling set 92599 which includes an optional fan perfectly sized 2ox2omm pre wired ONLY FOR BRUSHED MOTORS Motors with no capa citors or not enough capacitors may interfere with the speed control To avoid this solder the supplied capaci tors to your motor see picture Brushless motors do not require an additional suppres sion Racing motor CAUTION Never use Schottky diodes in conjunction Ear with a brushless or forward reverse brushed speed control e g the NOSRAM EVIL BRUSHLESS POWER REVERSE Mabuchi motor NOSRAM 2007 Dear customer thank you for your trust in this NOSRAM product By purchasing a NOSRAM EVIL BRUSHLESS POWER REVERSE speed control you have chosen a high performance brushless brushed speed control With this unit NOSRAM presents the promising sensor brushless technology as a sports level Brushless Brushed speed control The main features of this NOSRAM EVIL BRUSHLESS POWER REVERSE speed control are e 100 Automatic Adaptation e Brushless Brushed e NIMH NiCd LiPo e 4 5 and 6 cell optimised e Waterproof e Fail Safe
Download Pdf Manuals
Related Search