Home

Datasheet - Mouser Electronics

1. 2012 Digi International Inc 95 XBee 865 868LP RF Modules SMT Pin Through Hole Pin AD3 DIO3 AD2 DIO2 AD1 DIO1 ADO DIOO reserved GND RF reserved Mounting One of the important differences between the SMT and the through hole modules is the way they mount to the PCB The XBee through hole module is designed with through hole pins while the SMT module is designed with Surface Mount Technology SMT As such different mounting techniques are required Digi International has designed a footprint which will allow either module to be attached to a PCB The layout is shown below All dimensions are in inches 2012 Digi International Inc 96 XBee 865 868LP RF Modules 2i Bf LJ B B fa The round holes in the diagram are for the XBee through hole design and the semi oval pads are for the XBee SMT design Pin 1 of the through hole design is lined up with pin 1 of the SMT design but the pins are actually offset by one pad see Pin Mapping above By using diagonal traces to connect the appropriate pins the layout will work for both modules Information on attaching the XBee SMT module is included in Appendix C below 2012 Digi International Inc 97 Appendix C Manufacturing Information The XBee SMT module is designed for surface mount on the OEM PCB It has castellated pads to allow for easy sol der attach ins
2. Example 1 To update the DH DL registers of all modules in the network to be equal to the MAC address of an aggregator node with a MAC address of 0x0013a2004052c507 after network deployment the following technique could be employed 1 Deploy all modules in the network with the default DH DL of OxFFFF 2 Issue an ATAGFFFF command on the aggregator node Following the preceding sequence would result in all of the nodes in the network which received the AG broadcast to have a DH of 0x0013a200 and a DL of 0x4052c507 These nodes would have automatically built a route to the aggregator Example 2 To cause all nodes in the network to build routes to an aggregator node with a MAC address of 0x0013a2004052c507 without affecting the DH DL of any nodes in the network the ATAGFFFE command should be issued on the aggregator node This will cause an AG broadcast to be sent to all nodes in the network All of the nodes will update their internal routing table information to contain a route to the aggregator node None of the nodes will update their DH DL registers because none of the registers are set to an address of 0xFFFE Node Replacement 2012 Digi International Inc The AG command can also be used to update the routing table and DH DL registers in the network after a module is replaced The DH DL registers of nodes in the network can also be updated To update only the routing table information without affecting the DH DL registers then t
3. Is Sleep Coordinator Wait Random Holdoff Listen for Listen for Relay of Sync Relay of Sync Ever been Sync ed Is node a non sleep coord node which has lost sync Coord Rapid Sync Disabled Exit Deployment Mode Network Transmit Time Wait Sleep Guard Time Is Cyclic Sleep Node Wait Sleep Time in Low Power Mode 2012 Digi International Inc XBee 865 868LP RF Modules Becoming a Sleep Coordinator A node can become a sleep coordinator in one of four ways Preferred Sleep Coordinator Option A node can be specified to always act as a sleep coordinator This is done by setting the preferred sleep coordinator bit bit 0 in the sleep operations parameter SO to 1 A node with the sleep coordinator bit set will always send a sync message at the beginning of a wake cycle For this reason it is imperative that no more than one node in the network has this bit set Although it is not necessary to specify a preferred sleep coordinator it is often useful to select a node for this purpose to improve network performance A node which is centrally located in the network can serve as a good sleep coordinator to minimize the number of hops a sync message must take to get across the network A sleep support node and or a node which is mains powered may be a good candidate The preferred sleep coordinator bit sho
4. 4 Set the SP and ST values on the sleep coordinator to the desired values for the deployed network 5 Wait a cycle for the sleeping nodes to sync themselves to the new SP and ST values 6 Disable the preferred sleep coordinator option bit on the sleep coordinator unless a preferred sleep coordinator is desired 7 Deploy the nodes to their positions Alternatively nodes can be set up with their sleep pre configured and written to flash using the WR command prior to deployment If this is the case the commissioning button and associate LED can be used to aid in deployment 1 If a preferred sleep coordinator is going to be used in the network deploy it first If there will be no preferred sleep coordinator select a node for deployment power it on and press the commissioning button twice This will cause the node to begin emitting sync messages Verify that the first node is emitting sync messages by watching its associate LED A slow blink indicates that the node is acting as a sleep coordinator 2 Next power on nodes in range of the sleep coordinator or other nodes which have synchronized with the network If the synchronized node is asleep it can be woken by pressing the commissioning button once 3 Wait a cycle for the new node to sync itself 4 Verify that the node syncs with the network The associate LED will blink when the module is awake and synchronized 5 Continue this process until all nodes have been depl
5. 865 868LP RF Modules For example if you enabled 2 channels you would have an effective duty cycle of 5 6 The XBee radio uses a sliding bucket algorithm to calculate usage over the period of 1 hour for each channel Each bucket accumulates for 6 minutes This radio has a maximum of 30 AFA channels that it can choose from and channels can be excluded by setting the channel mask CM to reduce them Since not all countries allow for all of these channels the set may be dramatically smaller for some countries For a complete list refer to www digi com g4 Band Mode When the channel mask is set to 0x200000000 the radio will be in g4 band mode In this mode e LBT AFA mode is disabled e Module assumes no duty cycle requirement or 100 duty cycle e The PL setting must be set to 5 mW to comply with g4 band regulations Serial Communications XBee RF Modules interface to a host device through a serial port Through its serial port the module can communicate with any logic and voltage compatible UART through a level translator to any serial device for example through a RS 232 or USB interface board or through a Serial Peripheral Interface SPI which is a synchronous interface to be described later UART Data Flow Devices that have a UART interface can connect directly to the pins of the RF module as shown in the figure below System Data Flow Diagram in a UART interfaced environment Low asserted signals distingu
6. The DH and DL commands should be set to the address of the remote 0 for the coordinator or the 64 bit address of the remote After exiting command mode any received serial characters will be transmitted to the remote device and returned to the sender API Configuration AP 1 or AP 2 Send an Explicit Addressing Command API frame 0x11 using 0x12 as the cluster ID and OxE8 as the source and destination endpoint Data packets received by the remote will be echoed back to the sender RSSI Indicators It is possible to measure the received signal strength on a device using the DB command DB returns the RSSI value measured in dBm of the last received packet However this number can be misleading in DigiMesh networks The DB value only indicates the received signal strength of the last hop If a transmission spans multiple hops the DB value provides no indication of the overall transmission path or the quality of the worst link it only indicates the quality of the last link and should be used sparingly The DB value can be determined in hardware using the RSSI PWM module pin pin 6 If the RSSI PWM functionality is enabled PO command when the module receives data the RSSI PWM is set to a value based on the RSSI of the received packet Again this value only indicates the quality of the last hop This pin could potentially be connected to an LED to indicate if the link is stable or not Device Discovery Network Discovery
7. A user can update their application using the bootloader in an over the air configuration with the following steps This procedure assumes that the bootloader is running and not the application The internal microcontroller baud rate of the programmable module must be set to 115200 baud The bootloader only operates at 115200 baud between the Radio and programmable bootloader The application must be programmed with some way to support returning to the bootloader in order to support Over the Air OTA updates without local intervention a Open a hyperterminal session to the host module with no parity no hardwareflow control 8 data bits and 1 stop bit The host module does not have to operate at the same baud rate as the remote module For faster updates and less latency due to the UART set the host module to a faster baud rate i e 115200 b Enter 3 pluses to place the module in command mode or XCTU s Modem Configura tion tab can be used to set the correct parameters c Set the Host Module destination address to the target module s 64 bit address that the host module will update ATDH aabbccdd ATDL eeffgghh ATCN where aabbccddeeffgghh is the hexa decimal 64 bit address of the target module d Hit Enter and the bootloader command menu will be displayed from the remote module Note that the option B doesn t exist for OTA e Hit the F key to cause the remote module to request the new firmware file ov
8. QIOId ISON71gS lt gt SOWA sadv d L SiaNOA 18Le A sadoud pees o pajqeue PN SIOIG OSIN 145 lt gt r osmzzasa suav xases suten za1s H gt ZOld zav suoys sau dn jind jeusezur aaeq o pasu surd eY 2 O0N Saly no yg 01d 743SS lds gt H sea cay son caterers L lt gt voia _ IWS Jamod mo 898 338X Bg Nee Bees vale osIW MDZNdL yale Hoa 91 peu Zod AEE Ig 82 O d 238x 339X 100 sald SSI S81d lt gt EOI ECY asaueie sip SJemp Jey e ususpuny SUUJSI ep Hg Deenen gt ues asem jos 95 pasn aJe 9 S gt 3ld suid s yl s anaeanis cald Tasas jaa OIM BIOIG NL LY IAS C gt eszen ssenav ocav enaingi esnawevie Hea godano 2dy H azaoa lg Addy AHOZNAL ahBA IvLe He Of P 8H 601d 7d 33 1S NO ver zaziawzasa zaavzvaszzanawzvia He lt O l OIG IWMed 59 ped 4d COO ee azi vedia eaavzoszeaawevis Hec IOI 1d 38 gt a Ho o pew sola Jossy vaarana SN A9 B O1GNIY HV Le aoxa Ped ay Bold 08 d 3315 7810 J saziawsate asay aNL OuI S r J Q 4014 519 gt H wazawa BaavszHamassavie bag SYld 13534 Paa 21 peyT514 DO daz cate seavseHoenai evis Ha gt equ ava a rt ze as aa euuayue God pappaqua Jo uor oauuog oN eae L4OZEIOBASEIN ajeasealy 8 J0 3auu03 Jy ase suol do euUa Uue say o ay uolydo peg JH ay uo aAlyoe Ajuo si peg J4 Q i Ra LNS 898 x VANANVESDOYd S ad Eag XBee 865 868LP RF Modules igi 2012 D XBee 865 868LP RF Mod
9. The network discovery command can be used to discover all Digi modules that have joined a network Issuing the ND command sends a broadcast network discovery command throughout the network All devices that receive the command will send a response that includes the device s addressing information node identifier string see NI command and other relevant information This command is useful for generating a list of all module addresses in a network When a device receives the network discovery command it waits a random time before sending its own response The maximum time delay is set on the ND sender with the NT command The ND originator includes its NT setting in the transmission to provide a delay window for all devices in the network Large networks may need to increase NT to improve network discovery reliability The default NT value is 0x82 13 seconds Neighbor Polling The neighbor poll command can be used to discover the modules which are immediate neighbors within RF range of a particular node This command is useful in determining network topology and determining possible routes The command is issued using the FN command The FN command can be initiated locally on a node using AT command mode or by using a local AT 2012 Digi International Inc 3 XBee 865 868LP RF Modules command request frame The command can also be initiated remotely by sending the target node an FN command using a remote AT command request
10. UART Data Frame Structure with escape control characters Start Delimiter Length Frame Data Checksum Byte 1 Bytes 2 3 Bytes 4 n Byte n 1 0x7E MSB LSB API specific Structure 1 Byte Characters Escaped If Needed MSB Most Significant Byte LSB Least Significant Byte Escape characters When sending or receiving a UART data frame specific data values must be escaped flagged so they do not interfere with the data frame sequencing To escape an interfering data byte insert Ox7D and follow it with the byte to be escaped XOR d with 0x20 2012 Digi International Inc 77 XBee 865 868LP RF Modules Data bytes that need to be escaped e Ox7E Frame Delimiter e Ox7D Escape e 0x11 XON e 0x13 XOFF Example Raw UART Data Frame before escaping interfering bytes Ox7E 0x00 0x02 0x23 0x11 OxCB 0x11 needs to be escaped which results in the following frame Ox7E 0x00 0x02 0x23 0x7D 0x31 OxCB Note In the above example the length of the raw data excluding the checksum is 0x0002 and the checksum of the non escaped data excluding frame delimiter and length is calculated as OxFF 0x23 0x11 0xFF 0x34 OxCB Length The length field has two byte value that specifies the number of bytes that will be contained in the frame data field It does not include the checksum field Frame Data Frame data of the UART data frame forms an API specific structure
11. blink their Associate LEDs rapidly for 1 second All API devices that receive this transmission will send a Node Identification frame out their UART API ID 0x95 2 Not configured for synchronous sleep No effect Causes a node which is configured with sleeping router nomination enabled see description of the ATSO sleep options 2 Configured for synchronous sleep command in the XBee module s Product Manual to immediately nominate itself as the network sleep coordinator 4 Any Issues an ATRE to restore module parameters to default values Button presses may be simulated in software using the ATCB command ATCB should be issued with a parameter set to the number of button presses to execute i e sending ATCB1 will execute the action s associated with a single button press The node identification frame is similar to the node discovery response frame it contains the device s address node identifier string NI command and other relevant data All API devices 41 XBee 865 868LP RF Modules that receive the node identification frame send it out their UART as an API Node Identification Indicator frame 0x95 Associate LED The Associate pin pin 15 can provide indication of the device s sleep status and diagnostic information To take advantage of these indications an LED can be connected to the Associate pin as shown in the figure above The Associate LED functionality is en
12. it will also transmit and that data will normally be invalid Likewise whenever data is transmitted invalid data will probably be received The means of determining whether or not received data is invalid is by packetizing the data with API packets SPI allows for valid data from the slave to begin before at the same time or after valid data begins from the master When the master is sending data to the slave and the slave has valid data to send in the middle of receiving data from the master this allows a true full duplex operation where data is valid in both directions for a period of time Not only must the master and the slave both be able to keep up with the full duplex operation but both sides must honor the protocol as specified An example follows to more fully illustrate the SPI interface while valid data is being sent in both directions Clk EEEE MMM MOSI XXXVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVI IHIH 1XXXXXXXXXXX MISO XXX EEEE EEEVVVVVVVVVVVVVVVVVVVVVVVVVVI I1 EE XXXXXXXX SSEL ga a i a oS AVON eetechacenenneneecteanenee O S a ee enenee In the above character oriented timing diagram the notations mean the following indicates a low voltage signal indicates a high voltage signal III indicates an oscillating clock XXX indicates don t care data that will not be processed VVV indicates valid data that should be processed LLI indicates invalid data that should be discarded Low Power Operation In general sleep
13. jonstration of how the loopback cluster ID and data endpoint can be used to measure the link quality in a mesh network The configuration steps to send data to the loopback cluster ID depend on the AP setting AT Configuration AP 0 To send data to the loopback cluster ID on the data endpoint of a remote device set the Cl command value to 0x12 The SE and DE commands should be set to OxE8 default value The DH and DL commands should be set to the address of the remote After exiting command mode any received serial characters will be transmitted to the remote device and returned to the sender API Configuration AP 1 or AP 2 Send an Explicit Addressing ZigBee Command API frame 0x11 using 0x12 as the cluster ID and OxE8 as the source and destination endpoint Data packets received by the remote will be echoed back to the sender Link Testing Between Adjacent Devices 2012 Digi International Inc It is often advantageous to test the quality of a link between two adjacent nodes in a network The Test Link Request Cluster ID can be used to send a number of test packets between any two nodes in a network A link test can be initiated using an Explicit API command frame The command frame should be addressed to the Test Link Request Cluster ID 0x0014 on destination endpoint OxE6 on the radio which should execute the test link The Explicit API command frame should contain a 12 byte payload with the following format 38
14. API frame A node which executes an FN command will send a broadcast to all of its immediate neighbors All radios which receive this broadcast will send an RF packet to the node that initiated the FN command In the case where the command is initiated remotely this means that the responses are sent directly to the node which sent the FN command to the target node The response packet is output on the initiating radio in the same format as a network discovery frame Link Reliability For a mesh network installation to be successful the installer must be able to determine where to place individual XBee devices to establish reliable links throughout the mesh network Network Link Testing Source re and sends received data packet out the Dem A good way to measure the performance of a mesh network is to send unicast data through the network from one device to another to determine the success rate of many transmissions To simplify link testing the modules support a loopback cluster ID 0x12 on the data endpoint OxE8 Any data sent to this cluster ID on the data endpoint will be transmitted back to the sender This is shown in the figure below The remote device receives data on the loopback cluster ID and data endpoint Transmit data to the loopback cluster 1D 0x12 and data endpoint 0xE8 on a remote device Remote transmits the meived packet back to the sencer ceives loopback transmission UAR
15. Bitfield e t 17 0x54 18 0x78 19 0x44 20 0x61 21 0x74 22 0x61 23 0x30 24 0x41 Data that is sent to the destination device 25 0x13 OxFF the 8 bit sum of bytes from offset 3 to this byte Example The example above shows how to send a transmission to a module where escaping is disabled AP 1 with destination address 0x0013A200 40014011 payload TxData0A If escaping is enabled AP 2 the frame should look like Ox7E 0x00 0x16 0x10 0x01 0x00 Ox7D 0x33 OxA2 0x00 0x40 Ox0A 0x01 0x27 OxFF OxFE 0x00 0x00 0x54 0x78 0x44 0x61 0x74 0x61 0x30 0x41 0x7D 0x33 The checksum is calculated on all non escaped bytes as 0xFF sum of all bytes from API frame type through data payload Explicit Addressing Command Frame Frame Type 0x11 Allows application layer fields endpoint and cluster ID to be specified for a data transmission Similar to the Transmit Request but also requires application layer addressing fields to be specified endpoints cluster ID profile ID An Explicit Addressing Request API frame causes the 2012 Digi International Inc 82 XBee 865 868LP RF Modules module to send data as an RF packet to the specified destination using the specified source and destination endpoints cluster ID and profile ID The 64 bit destination address should be set to 0x000000000000FFFF for a broadcast transmission to all devices For unicast transmissions the 64 bit address
16. Disable lone coordinator sync repeat For ansynchronous sleep modules the following sleep options are defined bit 8 Always wake for ST time Wake Time Set read the wake period of the module For asynchronous sleep modules this command defines the amount of time that the ST module will stay awake after receiving RF or serial data 0x45 0x36EE80 0x7D0 2 seconds For synchronous sleep modules this command defines the amount of time that the module will stay awake when operating in cyclic sleep mode This value will be adjusted upwards automatically if it is too small to function properly based on other settings Sleep Period SP Set read the sleep period of the module This command defines the amount of time the 1 1440000 x 10 ms 2 seconds module will sleep per cycle Number of Missed Syncs MS Read the number of wake cycles that have elapsed since the last sync message was received Supported in the 80k firmware variant only Number of Sleep Periods Set read the number of sleep periods value This command controls the number of sleep periods that must elapse between assertions of the ON_SLEEP line during the SN wake time of asynchronous cyclic sleep During cycles when the ON_SLEEP line is not 1 OxFFFF 1 asserted the module will wake up and check for any serial or RF data If any such data is recieved then the ON_SLEEP line will be asserted and the module will fully wake up Otherwise the module will return to sleep after checking This
17. GPM response will be output as an explicit API RX indicator frame on the requesting node assuming API mode is enabled The format of the response is very similar to the request packet ie i li eal a Field Name General Field Description 0 1 GPM_CMD_ID This field will be the same as the request field 1 1 GPM_STATUS Status indicating whether the command was successful 2 2 GPM_BLOCK_NUM The block number addressed in the GPM 4 9 GPM_START_INDEX The byte index within the addressed GPM block 6 2 GPM_NUM_BYTES The number of bytes in the GPM_DATA field 7 varies GPM_DATA Multi byte parameters should be specified with big endian byte ordering The following commands exist for interacting with GPM PLATFORM_INFO_ REQUEST 0x00 A PLATFORM_INFO_REQUEST frame can be sent to query details of the GPM structure Field Name Command Specific Description GPM_CMD_ID Should be set to PLATFORM_INFO_REQUEST 0x00 GPM_OPTIONS GPM_BLOCK_NUM This field is unused for this command Set to 0 This field is unused for this command Set to 0 GPM_START_INDEX This field is unused for this command Set to 0 GPM_NUM_BYTES This field is unused for this command Set to 0 GPM_DATA No data bytes should be specified for this command PLATFORM_INFO 0x80 When a PLATFORM_INFO_REQUEST command request has been unicast to a node that node will send a response in the following fo
18. NT 100 milliseconds or a parameter is not specified left blank the command is terminated and an ERROR message is returned In the case of an ERROR Command Mode is not exited 20 byte ascii string 2012 Digi International Inc XBee 865 868LP RF Modules Node Identification Commands AT Command ND Name and Description Network Discover Discovers and reports all RF modules found The following information is reported for each module discovered MY lt CR gt always OxFFFE SH lt CR gt SL lt CR gt NI lt CR gt Variable length PARENT_NETWORK ADDRESS 2 Bytes lt CR gt always OxFFFE DEVICE_TYPE lt CR gt 1 Byte 0 Coord 1 Router 2 End Device See the NO Command STATUS lt CR3 gt 1 Byte Reserved PROFILE_ID lt CR gt 2 Bytes MANUFACTURER_ID lt CR gt 2 Bytes DIGI DEVICE TYPE lt CR gt 4 Bytes Optionally include based on NO settings RSSI lt CR gt 1 Byte Optionally include based on NO settings lt CR gt If the ND command is issued in command mode after NT 100 ms overhead time the command ends by returning a lt CR gt If the ND command is issued via a Local Command Request API frame each response is returned as a separate Local AT Command Response API packet The data consists of the above listed bytes without the carriage return delimiters The NI string will end in a 0x00 null character Parameter Range Default NO Network Discovery
19. See Data Transmission and Routing in chapter 4 for more information Receive Mode If a valid RF packet is received the data is transferred to the serial transmit buffer This is the default mode for the XBee radio Command Mode To modify or read RF Module parameters the module must first enter into Command Mode a state in which incoming serial characters are interpreted as commands The API Mode section in Chapter 7 describes an alternate means for configuring modules which is available with the SPI as well as over the UART with code AT Command Mode To Enter AT Command Mode Send the 3 character command sequence and observe guard times before and after the com mand characters Refer to the Default AT Command Mode Sequence below Default AT Command Mode Sequence for transition to Command Mode No characters sent for one second GT Guard Times parameter 0x3E8 Input three plus characters within one second CC Command Sequence Character parame ter 0x2B No characters sent for one second GT Guard Times parameter 0x3E8 Once the AT command mode sequence has been issued the module sends an OK r out the UART pad The OK r characters can be delayed if the module has not finished transmitting received serial data When command mode has been entered the command mode timer is started CT command and the module is able to receive AT commands on the UART port All of the paramete
20. The data starts with AINO and continues sequentially for each enabled analog input channel up to AINS If the IS command is issued from AT command mode then a carriage return delimited list will be returned containing the above listed fields If the command is issued via an API frame then the module will return an AT command response API frame with the IO data included in the command data portion of the packet Example Sample AT Response Ox01 r 1 sample set Digital Inputs DIO 2 3 10 11 Ox0C0C r enabled Ox03 r Analog Inputs A D 0 1 enabled Digital input states DIO 3 10 high DIO 2 11 low 0x03D0 r Analog input ADIO 0 0x3D0 0x0124 r Analog input ADIO 1 0x120 0x0408 r Periodic I O Sampling Periodic sampling allows an XBee PRO module to take an I O sample and transmit it to a remote device at a periodic rate The periodic sample rate is set by the IR command If IR is set to 0 periodic sampling is disabled For all other values of IR data will be sampled after IR milliseconds have elapsed and transmitted to a remote device The DH and DL commands determine the destination address of the 1O samples Only devices with API mode enabled will send 1O data samples out their UART Devices not in API mode will discard received 1O data samples A module with sleep enabled will transmit periodic 1 O samples at the IR rate until the ST time expires and the device can resume sleeping See the
21. an ebin file The contents of the ebin file should be stored in order in the appropriate GPM memory blocks The number of bytes that are sent in an individual GPM WRITE frame is flexible and can be catered to the user application Example XBee DigiMesh 868 firmware version 80xx has an ebin file of 55 141 bytes in length Based on network traffic it was determined that sending a 128 byte packet every 30 seconds minimized network disruption For this reason the ebin should be divided and addressed as follows 2012 Digi International Inc 51 XBee 865 868LP RF Modules GPM_BLOCK_NUM GPM_START_INDEX GPM_NUM_BYTES ebin bytes 0 0 128 0 to 127 0 128 128 128 to 255 0 256 128 256 to 383 0 384 128 384 to 511 0 128 512 to 639 128 128 640 to 767 107 0 54784 to 54911 107 128 54912 to 55039 107 256 101 55040 to 55140 Verifying the New Application For an uploaded application to function correctly every single byte from the ebin file must be properly transferred to the GPM To guarantee that this is the case GPM VERIFY functions exist to ensure that all bytes are properly in place The FIRMWARE_VERIFY function reports whether or not the uploaded data is valid The FIRMWARE_VERIFY_AND_INSTALL command will report if the uploaded data is invalid If the data is valid it will begin installing the application No installation will take place on invalid data Installing the Appli
22. are transmitted MT 1 times to ensure it is received Parameter Range Default Unicast Mac Retries Set Read the maximum number of MAC level packet delivery attempts for unicasts If RR is non zero packets sent from the radio will request an acknowledgement and can be resent up to RR times if no acknowledgements are received Network ID Set or read the user network identifier Nodes must have the same network identifier to communicate Changes to ID can be written to non volatile memory using the WR command 0x0000 to Ox7FFF Ox7FFF Power Level Set Read the power level at which the RF module transmits conducted power 2012 Digi International Inc 0 0dBm 1 5dBm 2 8dBm 3 10dBm 4 12 dBm 74 XBee 865 868LP RF Modules DigiMesh Mesh Commands Network Level Commands Some of these commands are supported on both the 10k and 80k variants AT Command Name and Description Network Hops Set or read the maximum number of hops expected to be seen in a network route This value doesn t limit the number of hops allowed but it is used to calculate timeouts waiting for network acknowledgements Supported in both variants Parameter Range 1 to Oxff Default Sleep Sleep Commands AT Command Mesh Network Retries Set or read the maximum number of network packet delivery attempts If MR is non zero packets sent will request a network acknowledgement and can be resent up t
23. as follows Figure 7 03 UART Data Frame amp API specific Structure Start Delimiter Length Frame Data Checksum Byte 1 Bytes 2 3 Bytes 4 n Byte n 1 Ox7E MSB LSB API specific Structure 1 Byte API Identifier Identifier specific Data cmdiD cmdData The cmdlD frame APl identifier indicates which API messages will be contained in the cmdData frame Identifier specific data Note that multi byte values are sent big endian The XBee modules support the following API frames API Frame Names and Values API Frame Names API ID AT Command 0x08 AT Command Queue Parameter Value 0x09 Transmit Request 0x10 Explicit Addressing Command Frame 0x11 Remote Command Request 0x17 AT Command Response 0x88 Modem Status 0x8A Transmit Status 0x8B Receive Packet AO 0 0x90 Explicit Rx Indicator AO 1 0x91 Node Identification Indicator AO 0 0x95 Remote Command Response 0x97 2012 Digi International Inc 78 XBee 865 868LP RF Modules Checksum To test data integrity a checksum is calculated and verified on non escaped data To calculate Not including frame delimiters and length add all bytes keeping only the lowest 8 bits of the result and subtract the result from OXxFF To verify Add all bytes include checksum but not the delimiter and length If the checksum is correct the sum will equal OxFF API UART Exchanges AT Commands The followi
24. data API Output Format Enables different API output frames Options include AO 0 Standard Data Frames 0x90 for RF RX 1 Explicit Addressing Data Frames 0x91 for RF RX Parameter Range 0 1 or 2 0 1 Default Baud rate Set or read serial interface rate speed for data transfer between radio modem and host Values from 0 8 select preset standard rates Values at 0x39 and above select the actual baud rate Providing the host supports it Baud rates can go as high as 1 875Mbps The values from 0 to 8 are interpreted as follows BD 0 1 200bps 3 9 600bps 6 57 600bps 1 2 400bps 4 19 200bps 7 115 200bps 2 4 800bps 5 38 400bps 8 230 400bps 0 to 8 and 0x39 to 0x1c9c38 0x03 9600 bps Packetization Timeout Set Read number of character times of inter character silence RO required before packetization Set RO 0 to transmit characters as they arrive instead of buffering them into one RF packet 0 OXFF x character times Flow Control Threshhold Set or read flow control threshhold De assert CTS and or FT send XOFF when FT bytes are in the UART receive buffer Re assert CTS when less than FT 16 bytes are in the UART receive buffer 0x11 OxEE OxBE 190d Parity Set or read parity settings for UART communications The values from 0 to 4 are interpreted as follows NB 0 No parity 3 Forced high parity 1 Even parity 4 Forced low parity 2 Odd parity 0to4 0 No parity DIO7 Configurat
25. exact transmission method is determined by the data rate of your module In the 10k version the network is set in a repeater mode where there is no route discovery The transmission is simply sent out to the network and each radio will repeat the message to its neighboring radios There is no route discovery in this method On the 80k version of the module the transmission is directed to a specific IP address using a route discovered by a router module In both methods all transmissions are broadcasts not unicast messages Point to Point Multipoint In this mode there is a permanent link between two endpoints Switched point to point topologies are the basic model of conven tional telephony The value of a permanent point to point network is unimpeded communications between the two endpoints The value of an on demand point to point connection is proportional to the number of potential pairs of subscribers Permanent dedicated One of the variations of point to point topology is a point to point communications channel that appears to the user to be permanently associated with the two endpoints Within many switched telecommunications systems it is possible to establish a permanent circuit One example might be a telephone in the lobby of a public building which is programmed to ring only the number of a telephone dispatcher Nailing down a switched connection saves the cost of running a physical circuit between the two points The resourc
26. field should be set to the address of the desired destination node The reserved field should be set to OxFFFE The broadcast radius can be set from 0 up to NH to OxFF If the broadcast radius exceeds the value of NH then the value of NH will be used as the radius This parameter is only used for broadcast transmissions The maximum number of payload bytes can be read with the NP command Number of bytes between the length and the checksum Identifies the UART data frame for the host to correlate with a subsequent ACK acknowledgement If set to 0 no response is sent Set to the 64 bit address of the destination device The following address is also supported Ox000000000000FFFF Broadcast address Set to OXFFFE Source endpoint for the transmission Destination endpoint for the transmission Cluster ID used in the transmission Profile ID used in the transmission Sets the maximum number of hops a broadcast transmission can traverse If set to 0 the transmission radius will be set to the network maximum hops value Bitfield bit 0 Disable ACK bit 1 Don t attempt route Discovery bit 2 Enable Unicast NACK messages bit 3 Enable Unicast Trace Route messages All other bits must be set to 0 OxFF the 8 bit sum of bytes from offset 3 to this byte Example The above example sends a data transmission to a radio with a 64 bit addres
27. for optimal performance this module should not be mounted on the RF Pad footprint described in the next section because the footprint requires a ground plane within the PCB Antenna keep out area 2012 Digi International Inc 12 XBee 865 868LP RF Modules Minimum Keepout Area PCB Antenna All 83 82mm gt for Layers 33 Thou 15 24mm 6 Thou SA No metal in keepout All Layers pout Ar k 19 Thou 4 8mm 3 o E t Limited routing is permitted in this area such F as connecting pad 35 to Ground However Ground pours are not recommended in this area Recommended Keepout Area for PCB Antenna All Layers j 111 7 9mm gt Je 44 8Thou gt Sif y 7 were No metal in keepout All Layers E 2 ase E o t N OOK 1n E A SX o PLR o in 2 sa Te x X OS 4 Preferred Edge of board x 5 TT When possible keep XBee close mat Va to edge of board 4 4 O x of EE FO 3 7 E oo 8m Ee co 8 o E N nm N 8 G The antenna performance improves with a larger keepout area H Notes 1 Non Metal enclosures are recommended For metal enclosures an external antenna should be used 2 Metal chassis or mounting structures in the keepout area should be at least 1 inch 2 54 cm al away from antenna 3 Maximize distance between antenna and metal object
28. from 0x0000 to the code space with the same number Often 0x00 or OxFF These extra bytes before the APP code starts will need to be deleted from the bin file before the file can be transferred to the bootloader 2012 Digi International Inc bo Go 2 RF Module Operation Basic Operational Design The XBee 865 868LP RF Module uses a multi layered firmware base to order the flow of data dependent on the hardware and software configuration chosen by the user This configuration block diagram is shown below with the host serial interface as the physical starting point and the antenna as the physical endpoint for the transferred data As long as a block is able to touch another block the two interfaces can interact For example if the module is using SPI mode Transparent Mode is not available See below Host Serial Interface Transparent AT Command Mode Mode Mode Command Handler Packet Handler Network Layer DigiMesh Repeater MAC PHY Layer Point Multipoint Antenna The command handler is the code that processes commands from AT Command Mode or API Mode see AT Commands section The command handler can also process commands from remote radios see Remote AT Commands section Listen Before Talk Automatic Frequency Agility LBT AFA g Band Mode This radio implements LBT Listen Before Talk and AFA Automatic Frequency Agility The advantage of LBT AFA is that the radio can bypass t
29. include 0 Input unmonitored 1 Associate LED 2 Analog Input 3 Digital input monitored 4 Digital output low 5 Digital output high 0 OxFF x 100 ms 0 5 0 5 0x28 4 seconds D8 DIO8 SLEEP_RQ Configuration Configure options for the DIO8 SLEEP_RQ line of the module Options include 0 Input unmonitored 3 Digital input monitored 4 Digital output low 5 Digital output high When used as SLEEP_RQ the D8 parameter should be configured in mode 0 or 3 2012 Digi International Inc 70 XBee 865 868LP RF Modules I O Commands AT Command D9 Name and Description DIO9 ON SLEEP Configuration Configure options for the DIO9 ON SLEEP line of the module Options include 0 Input unmonitored 1 ON SLEEP 3 Digital input monitored 4 Digital output low 5 Digital output high Parameter Range 0 1 3 5 Default PR MO M1 LT Pull up Resistor Set read the bit field that configures the internal pull up resistor status for the I O lines 1 specifies the pull up resistor is enabled 0 specifies no pullup Bits 0 DIO4 AD4 Pin 11 AD3 DIO3 Pin 17 AD2 DIO2 Pin 18 AD1 DIO1 Pin 19 ADO DIOO Pin 20 RTS DIO6 Pin 16 DTR SLEEP_RQ D108 DIO8 Pin 9 DIN Config Pin 3 Associate DIO5 Pin 15 9 On Sleep DIO9 Pin 13 10 DIO12 Pin 4 11 PWMO RSSI D
30. is a unicast or a broadcast and if the route to the destination address is known Timeouts or timing information is pro vided for the following transmission types e Transmitting a broadcast e Transmitting a unicast with a known route e Transmitting a unicast with an unknown route e Transmitting a unicast with a broken route Note The timeouts in this section are theoretical timeouts and not precisely accurate The application should pad the calculated maximum timeouts by a few hundred milliseconds When using API mode Tx Status API packets should be the primary method of determining if a transmission has completed Unicast One Hop Time A building block of many of the calculations presented below is the unicastOneHopTime As its name indicates it represents the amount of time it takes to send a unicast transmission between two adjacent nodes It is dependent upon the H setting It is defined as follows unicastOneHopTime H Transmitting a broadcast A broadcast transmission must be relayed by all routers in the network The maximum delay would be when the sender and receiver are on the opposite ends of the network The NH and H parameters define the maximum broadcast delay as follows BroadcastTxTime NH 8 2012 Digi International Inc 55 XBee 865 868LP RF Moduless Transmitting a unicast with a known route When a route to a destination node is known the transmission time is largely a function of the number
31. is using that node will become the sleep coordinator That node will begin sending sync messages with the new sleep parameters at the beginning of the next wake cycle 2012 Digi International Inc 62 XBee 865 868LP RF Modules Note 1 For normal operations a module will use the sleep and wake parameters it gets from the sleep sync message not the ones specified in its SP and ST parameters The SP and ST parameters are not updated with the values of the sync message The current network sleep and wake times used by the node can be queried using the OS and OW commands Note 2 Changing network parameters can cause a node to become a sleep coordinator and change the sleep settings of the network The following commands can cause this to occur NH NN NQ and MR In most applications these network parameters should only be configured during deployment Sleep Guard Times To compensate for variations in the timekeeping hardware of the various modules in a sleeping router network sleep guard times are allocated at the beginning and end of the wake time The size of the sleep guard time varies based on the sleep and wake times selected and the number of cycles that have elapsed since the last sync message was received The sleep guard time guarantees that a destination radio will be awake when a transmission is sent As more and more consecutive sync messages are missed the sleep guard time increases in duration and decreases
32. module s unique IEEE 64 bit address 64 bit source address is always enabled This value is read only and it never changes Serial Number Low Read low 32 bits of the RF module s unique IEEE 64 bit address 64 bit source address is always enabled This is read only and it is also the serial number of the node Source Endpoint Set read the application layer source endpoint value This value will be used as the source endpoint for all data transmissions The default value OxE8 Data endpoint is the Digi data endpoint 0 0xFFFFFFFF 0 0xFFFFFFFF Factory Destination Endpoint Set read application layer destination ID value This value will be used as the destination endpoint for all data transmissions The default value 0xE8 is the Digi data endpoint Cluster Identifier Set read application layer cluster ID value This value will be used as the cluster ID for all data transmissions The default value 0x11 Transparent data cluster ID 0 0xFFFF Maximum RF Payload Bytes This value returns the maximum number of RF payload bytes that can be sent in a unicast transmission based on the current configurations 0 0xFFFF Node Messaging Options Set read options related to node type and messaging modes This command is a bitfield with the bits defined as follows bit 0 Indirect messaging coordinator enable All point multipoint unicasts will be held until requested by a polling end device bit 1 Disable Dig
33. module to send data as an RF packet to the specified destination The 64 bit destination address should be set to OxOOOOOOOOOOOOFFFF for a broadcast transmission to all devices For unicast transmissions the 64 bit address field should be set to the address of the desired destination node The reserved field should be set to OxFFFE This example shows if escaping is disabled AP 1 2012 Digi International Inc 81 XBee 865 868LP RF Modules 0 Ox7E MSB 1 0x00 Number of bytes between the length and the checksum LSB 2 0x16 3 0x10 Identifies the UART data frame for the host to correlate 4 0x01 with a subsequent ACK acknowledgement If set to 0 no response is sent bit 0 Disable ACK bit 1 Disable RD bit 2 Enable Unicast NACK messages 16 0x00 bit 3 Enable Unicast Trace Route messages bits 6 7 b 01 Point Multipoint b 10 Repeater mode directed broadcast b 11 DigiMesh not available on 10k product All other bits must be set to 0 MSB 5 0x00 6 0x13 7 OxA2 Set to the 64 bit address of the destination device The 8 0x00 A following address is also supported 9 0x40 0x000000000000FFFF Broadcast address 10 Ox0A 11 0x01 A LSB 12 0x27 13 OxFF i Set to OxFFFE 14 OxFE P Sets maximum number of hops a broadcast transmission a 15 0x00 can occur If set to 0 the broadcast radius will c be set to the maximum hops value k
34. of the node to which they need to transmit to In networks of transparent mode modules which transmit to an aggregator node it is necessary to set every module s DH DL registers to the MAC address of the aggregator node This can be a tedious process The AR command can be used to set the DH DL registers of all the nodes in a DigiMesh network to that of the aggregator node in a simple and effective method Upon deploying a DigiMesh network the AG command can be issued on the desired aggregator node to cause all nodes in the network to build routes to the aggregator node The command can optionally be used to automatically update the DH DL registers to match the MAC address of the aggregator node The AG command requires a 64 bit parameter The parameter indicates the current value of the DH DL registers on a module which should be replaced by the 64 bit address of the node sending the AG broadcast If it is not desirable to update the DH DL of the module receiving the AG broadcast then the invalid address of OxFFFE can be used API enabled modules will output an Aggregator Update API frame if they update their DH DL address see the API section of this manual for a description of the frame All modules which receive an AG broadcast will update their routing table information to build a route to the sending module regardless of whether or not their DH DL address is updated This routing information will be used for future transmissions of DigiMesh unicasts
35. replace and strengthen the weak link with new and or redundant modules to fix the problem and prevent it from occurring in the future When the default DigiMesh sleep parameters are used separated subnets will not drift out of phase with each other Subnets can drift out of phase with each other if the network is configured in one of the following ways e If multiple modules in the network have had the non sleep coordinator sleep option bit dis abled and are thus eligible to be nominated as a sleep coordinator e If the modules in the network are not using the auto early wake up sleep option If a network has multiple subnets that have drifted out of phase with each other get the subnets back in phase with the following steps 1 Place a sleep support node in range of both subnets 2 Select a node in the subnet that you want the other subnet to sync up with Use this node to slightly change the sleep cycle settings of the network increment ST for example 3 Wait for the subnet s next wake cycle During this cycle the node selected to change the sleep cycle parameters will send the new settings to the entire subnet it is in range of including the sleep support node which is in range of the other subnet 4 Wait for the out of sync subnet to wake up and send a sync When the sleep support node receives this sync it will reject it and send a sync to the subnet with the new sleep settings 5 The subnets will now be in sync The
36. sleep section for more information on sleep Digital O Change Detection Modules can be configured to transmit a data sample immediately whenever a monitored digital I O pin changes state The IC command is a bitmask that can be used to set which digital I O lines should be monitored for a state change If one or more bits in IC is set an O sample will be transmitted as soon as a state change is observed in one of the monitored digital I O lines The figure below shows how edge detection can work with periodic sampling 2012 Digi International Inc 44 XBee 865 868LP RF Modules Monitored Digital IO Line IO Sample Transmissions IR gt 0 IC 0 IO Sample Transmissions t IR e e E e 1 I I 1 1 LA I i i IR gt 0 IC gt 0 e tR k Enabling Edge Detection will force an immediate sample of all monitored digital IO lines if any digital IO lines change state General Purpose Flash Memory XBee 868LP modules provide 119 512 byte blocks of flash memory which can be read and written by the user application This memory provides a non volatile data storage area which can be used for a multitude of purposes Some common uses of this data storage include storing logged sensor data buffering firmware upgrade data for a host microcontroller or storing and retrieving data tables needed for calculations performed by a host microcontroller The General Purpose Memory GPM is a
37. that handles received serial API frames sent out the module s DOUT pin might look like this void XBee_HandleRxAPIFrame _apiFrameUnion papiFrame switch papiFrame gt api_id case RX_RF_DATA_FRAME process received RF data frame break case RX_IO_SAMPLE_FRAME process IO sample frame break case NODE_IDENTIFICATION_FRAME process node identification frame break default Discard any other API frame types that are not being used break Frame Data The following sections illustrate the types of frames encountered while using the API AT Command Frame Type 0x08 Used to query or set module parameters on the local device This API command applies changes after executing the command Changes made to module parameters take effect once changes are applied The API example below illustrates an API frame when modifying the NH parameter value of the module 2012 Digi International Inc 80 XBee 865 868LP RF Modules Start Delimiter 0 0x7E MSB 1 0x00 Length Number of bytes between the length and the checksum A LSB 2 0x04 3 0x08 Identifies the UART data frame for the host to correlate P 4 0x52 R with a subsequent ACK acknowledgement If set to 0 a no response is sent c Frame specific Data 5 0x4E N Command Name Two ASCII characters that identify the r 6 0x48 H AT Command t If present indicates the requested parameter value to set the given r
38. the master The SPI port uses the following signals on the XBee e SPI_MOSI Master Out Slave In inputs serial data from the master e SPI_MISO Master In Slave Out outputs serial data to the master e SPI_SCLK Serial Clock clocks data transfers on MOSI and MISO e SPI_SSEL Slave Select enables serial communication with the slave e SPI_ATTN Attention alerts the master that slave has data queued to send The XBee mod ule will assert this pin as soon as data is available to send to the SPI master and it will remain asserted until the SPI master has clocked out all available data In this mode the following apply e SPI Clock rates up to 3 5 MHz are possible e Data is MSB first e Frame Format mode 0 is used This means CPOL 0 idle clock is low and CPHA O data is sampled on the clock s leading edge Mode 0 is diagramed below e SPI port is setup for API mode and is equivalent to AP 1 Frame Format for SPI Communications Frame Format nSSEL Nd N ta bef hd MOSl K RX X RXI6 X RXIB X RXI4 X RX3 X RXIZ X RX X RXIO X MISOsa TXI7 X TX X TXS X TXA X TXB X TXI X TXI X TOX SPI Operation This section specifies how SPI is implemented on the XBee what the SPI signals are and how full duplex operations work XBee I mplementation of SPI The module operates as a SPI slave only This means that an external master will provide the clock and will decide when to sen
39. vary by a number of variables including number of hops encryption enabled disabled sleeping end devices failures route discoveries Our empirical testing showed the following throughput performance in a robust operating environment low interference 80 kbps version 115 2 kbps serial data rate 100 KB Configuration Data Throughput Mesh unicast 1 hop Encryption Disabled 35 6 kbps Mesh unicast 3 hop Encryption Disabled 11 9 kbps Mesh unicast 6 hop Encryption Disabled 7 1 kbps Mesh unicast 1 hop Encryption Enabled 35 3 kbps Mesh unicast 3 hop Encryption Enabled 11 8 kbps Mesh unicast 6 hop Encryption Enabled 7 0 kbps Point to point unicast Encryption Disabled 54 7 kbps Point to point unicast Encryption Enabled 53 9 kbps 10 kbps version 115 2 kbps serial data rate 100 KB Configuration Data Throughput Point to point unicast Encryption Disabled Point to point unicast Encryption Enabled Note Data throughput measurements were made setting the serial interface rate to 115200 bps and measuring the time to send 100 000 bytes from source to destination During the test no route discoveries or failures occurred Transmission Timeouts When a node receives an API TX Request API configured modules or an RO timeout occurs modules configured for Transparent Mode the time required to route the data to its destination depends on a number of configured parameters whether the trans mission
40. while the SPI master talks to the other slave but this is acceptable in most cases If neither pin is configured as a peripheral then the radio stays awake being unable to sleep in SM1 mode Configuration The three considerations for configuration are eHow is the serial port selected l e Should the UART or the SPI port be used elf the SPI port is used what should be the format of the data in order to avoid processing invalid characters while transmitting What SPI options need to be configured Serial Port Selection In the default configuration the UART and SPI ports will both be configured for serial port operation If both interfaces are configured serial data will go out the UART until the SPI_SSEL signal is asserted Thereafter all serial communications will operate on the SPI interface If only the UART is enabled then only the UART will be used and SPI_SSEL will be ignored If only the SPI is enabled then only the SPI will be used If neither serial port is enabled the module will not support serial operations and all communications must occur over the air All data that would normally go to the serial port is discarded Forcing UART Operation In the rare case that a module has been configured with only the SPI enabled and no SPI master is available to access the SPI slave port the module may be recovered to UART operation by holding DIN CONFIG low at reset time As always DIN CONFIG forces a de
41. 3 to this byte Example Suppose the BD parameter is changed on the local device with a frame ID of 0x01 If successful parameter was valid the above response would be received Modem Status Frame Type 0x8A RF module status messages are sent from the module in response to specific conditions Example The following API frame is returned when an API device powers up Start Delimiter Length 0 gt Frame specific Data 0 xov Checksum 2012 Digi International Inc 0 0x7E MSB 1 0x00 Number of bytes between the length and the checksum LSB 2 0x02 3 0x8A 0x00 Hardware reset 0x01 Watchdog timer reset 0x00 0x0B Network Woke Up 0x0C Network Went To Sleep 5 0x75 OxFF the 8 bit sum of bytes from offset 3 to this byte 85 XBee 865 868LP RF Modules Transmit Status Frame Type 0x8B When a TX Request is completed the module sends a TX Status message This message will indicate if the packet was transmitted successfully or if there was a failure Start Delimiter Number of bytes between the length and the checksum Identifies the UART data frame being reported Note If Frame ID 0 in AT Command Mode no AT Command Response will be given Reserved The number of application transmission retries that took Frame specific Data place 0x00 Success 0x01 MAC ACK Failure 0x15 Invalid destination endpoint 0x21 Network A
42. A newer version of the Bootloader BLO32 2x0 033_ 064 or newer BLO32 2BO0 XXX_064 has changed the baud rate to 115200 between the Programmable and 2012 Digi International Inc 21 XBee 865 868LP RF Modules the internal microcontroller The internal module is also set to 115200 as the default baud rate The default rate of the programmable local UART is also set to 115200 however the local UART has an auto baud feature added to detect if the UART is at the wrong baud rate If a single character is sent it will automatically switch to 115200 or 9600 baud Firmware Updates Wired Updates A user can update their application using the bootloader in a wired configuration with the following steps a Plug XBee programmable module into a suitable serial port on a PC b Open a hyperterminal or similar dumb terminal application session with 115200 baud no par ity and 8 data bits with one stop bit c Hit Enter to display the bootloader menu d Hit the F key to initiate a wired firmware update e A series of C characters Will be displayed within the hyperterminal window At this point select the transfer gt send file menu item Select the desired flat binary output file f Select Xmodem as the protocol g Click Send on the Send File dialog The file will be downloaded to the XBee Programmable module Upon a successful update the bootloader will jump to the newly loaded application Over The Air updates
43. CK Failure 0x25 Route Not Found 0x00 No Discovery Overhead 0x02 Route Discovery Checksum OxFF the 8 bit sum of bytes from offset 3 to this byte Example In the above example a unicast data transmission was sent successfully to a destination device using a frame ID of 0x47 Route Information Packet Frame type 0x8D A Route Information Packet can be output for DigiMesh unicast transmissions on which the NACK enable or the Trace Route enable TX option is enabled 2012 Digi International Inc 86 XBee 865 868LP RF Modules Number of bytes between the length and the checksum 0x11 NACK 0x12 Trace Route Number of bytes that follow excluding checksum If length increases then new items have been added to the end of the list for future revisions System timer value on the node generating the Route Information Packet The number of MAC ACK timeouts that occurred Reserved Reserved Address of the final destination node of this network level transmission Address of the source node of this network level transmission Address of the node that generated this Route Information Packet after sending or attempting to send the packet to the next hop the Reciever Node Address of the node to which the data packet was just sent or attempted to be sent to OxF
44. CKs are not used the originating node will send the broadcast multiple times By default a broadcast transmission is sent four times Essentially the extra transmissions become automatic retries without acknowledgments This will result in all nodes repeating the transmission four times as well In order to avoid RF packet collisions a random delay is inserted before each router relays the broadcast message See NN parameter for details on changing this random delay time Sending frequent broadcast transmissions can quickly reduce the available network bandwidth and as such should be used sparingly The broadcast address is a 64 bit address with the lowest 16 bits set to 1 The upper bits are set to 0 To send a broadcast transmission set DH to 0 and DL to OxFFFF In API mode the destination address would be set to OxOO0000000000F FFF Routing A module within a mesh network is able to determine reliable routes using a routing algorithm and table The routing algorithm uses a reactive method derived from AODV Ad hoc On demand Distance Vector An associative routing table is used to map a destination node address with its next hop By sending a message to the next hop address either the message will reach its destination or be forwarded to an intermediate router which will route the message on to its destination A message with a broadcast address is broadcast to all neighbors All routers receiving the message will rebroadcast the message MT 1 times a
45. F the 8 bit sum of bytes from offset 3 to this byte Example The above example represents a possible Route Information Frame that could be received when doing a trace route on a transmission from a radio with serial number 0x0013a2004052AAAA to a radio with serial number 0x0013a2004052DDDD This particular 2012 Digi International Inc 87 XBee 865 868LP RF Modules frame indicates that the transmission was successfully forwarded from the radio with serial number 0x0013a2004052BBBB to the radio with serial number 0x0013a2004052CCCC Aggregate Addressing Update Frame type Ox8E An Aggregate Addressing Update frame is output on an API enabled node when an address update frame generated by the AG command being issued on a node in the network causes the node to update its DH and DL registers Start Delimiter 0 Ox7E MSB 1 0x00 Length Number of bytes between the length and the checksum LSB 2 0x12 3 0x8E Byte reserved to indicate format of additional packet information which may be added in future firmware revisions In the current firmware revision 0x00 is returned in this field 4 0x00 MSB 5 0x00 6 0x13 OxA2 8 0x00 9 0x40 10 0x52 11 0xBB LSB 12 0xBB 0 gt Address to which DH and DL are being set Frame specific Data ORXTO DU 13 0x00 14 0x13 15 OxA2 16 0x00 17 0x40 18 0x52 19 OxAA 20 OxAA Address to w
46. IO10 Pin 6 12 PWM1 DIO11 Pin 7 13 DIOZ CTS Pin 12 14 DOUT Pin 2 PWMO Output Level Set read the output level of the PWMO line The line should be configured as a PWM output using the PO command PWM1 Output Level Set read the output level of the PWM1 line The line should be configured as a PWM output using the P1 command Assoc LED Blink Time Set Read the Associate LED blink time If the Associate LED functionality is enabled D5 command this value determines the on and off blink times for the LED If LT 0 the default blink rate will be used 500ms sleep coordinator 250ms otherwise For all other LT values LT is measured in 10ms Force Sample Forces a read of all enabled digital and analog input lines I O Digital Change Detection Set Read the digital I O pins to monitor for changes in the I O state IC works with the individual pin configuration commands D0 D9 PO P2 If a pin is enabled as a digital input output the IC command can be used to force an immediate I O sample transmission when the DIO state changes IC is a bitmask that can be used to enable or disable edge detection on individual channels Unused bits should be set to 0 Bit I O pin 0 DIO0 DIO1 oN oOoN AOON 0 D1010 11 D1011 12 D1012 10 Sample Rate Set Read the I O sample rate to enable periodic sampling For periodic sampling to be enabled IR must be set to a non zero value and at least one module pin m
47. Internal Pin Mappings Insert Table Design Notes The XBee modules do not specifically require any external circuitry or specific connections for proper operation However there are some general design guidelines that are recommended for help in troubleshooting and building a robust design Power Supply Design Poor power supply can lead to poor radio performance especially if the supply voltage is not kept within tolerance or is excessively noisy To help reduce noise we recommend placing both a 1uF and 8 2pF capacitor as near to pin 2 on the PCB as possible If using a switching regulator for your power supply switching frequencies above 500kHz are preferred Power supply ripple should be limited to a maximum 250mV peak to peak Note For designs using the programmable modules an additional 10uF decoupling cap is recommended near pin 2 of the module The nearest proximity to pin 2 of the three caps should be in the following order 8 2pf 1uF followed by 10pF Recommended Pin Connections The only required pin connections are VCC GND DOUT and DIN To support serial firmware updates VCC GND DOUT DIN RTS and DTR should be connected All unused pins should be left disconnected All inputs on the radio can be pulled high or low with 30k internal pull up or pull down resistors using the PR and PD software commands No specific treatment is needed for unused outputs For applications that need to ensure the lowest sleep curren
48. M_BYTES the GPM block size It is also important to remember that the number of bytes sent in an explicit API frame including the GPM command fields cannot exceed the maximum payload size of the radio The maximum payload size can be queried with the NP AT command GPM_DATA The data to be written WRITE _ RESPONSE 0x82 and ERASE_THEN_WRITE_RESPONSE 0x83 When a WRITE or ERASE_THEN_WRITE command request has been unicast to a node that node will send a response in the following format to the source endpoint specified in the requesting frame Field Name Command Specific Description Should be set to WRITE_RESPONSE 0x82 or GPM_CMD ID ERASE_THEN WRITE RESPONSE 0x83 GPM_STATUS A 1 in the least significant bit indicates an error occurred All other bits are reserved at this time GPM_BLOCK_NUM Matches the parameter passed in the request frame GPM_START_INDEX Matches the parameter passed in the request frame GPM_NUM_BYTES The number of bytes in the GPM_DATA field For this command this field will be set to 0 GPM_DATA No data bytes are specified for these commands Example To write 15 bytes of incrementing data to flash block 22 of a target radio with serial number of 0x0013a200407402ac a WRITE packet should be formatted as follows spaces added to delineate fields TE 002B 11 01 0013A200407402AC FFFE E6 E6 0023 C105 00 CO 02 00 0016 0000 000F 0102030405060708090AOBOCODOEOF C5 Assuming all transmissio
49. Options Set Read the options value for the network discovery command The options bitfield value can change the behavior of the ND network discovery command and or change what optional values are returned in any received ND responses or API node identification frames Options include 0x01 Append DD value to ND responses or API node identification frames 0x02 Local device sends ND or FN response frame when ND is issued 0x04 Append RSSI of the last hop for DigiMesh networks to ND or FN responses or API node identification frames 0x08 Enable Verbose Device Type field When enabled the device type field of ND and FN responses will contain the CE value of the responding node If the responding node is acting as a synchronized sleep coordinator then bit 7 will be set 0 0x07 bitfield Security Security Commands AT Name and Description Parameter Range Default Command EE Security Enable Enables or disables 128 bit AES encryption This command parameter Otol 0 should be set the same on all devices Security Key Sets the 16 byte network security key value This command is write only KY Attempts to read KY will return an OK status This command parameter should be set the 128 bit value n a same on all devices MAC Level MAC level Commands AT Command Name and Description Broadcast Multi Transmit Set Read the number of additional MAC level broadcast transmissions All broadcast packets
50. Response API packet respectively The data consists of the above listed bytes without the carriage return delimiters The NI string will end in in a 0x00 null character 0 OXFF Parameter Range n a 0x2B Default n a NT Node Discover Timeout Set Read the amount of time a node will spend discovering other nodes when ND or DN is issued 0 OxFC x 100 msec 0x82 130d NI Node Identifier Stores a string identifier The string accepts only printable ASCII data In AT Command Mode the string can not start with a space A carriage return or comma ends the command Command will automatically end when maximum bytes for the string have been entered This string is returned as part of the ATND Network Discover command This identifier is also used with the ATDN Destination Node command up to 20 byte ASCII string a space character DN Discover Node Destination Node Resolves an NI Node Identifier string to a physical address case sensitive The following events occur after the destination node is discovered lt AT Firmware gt 1 DL amp DH are set to the extended 64 bit address of the module with the matching NI Node Identifier string 2 OK or ERROR r is returned 3 Command Mode is exited to allow immediate communication lt API Firmware gt oe and 64 bit extended addresses are returned in an API Command Response rame If there is no response from a module within
51. T_INDEX This field is unused for this command Set to 0 GPM_NUM_BYTES This field is unused for this command Set to 0 GPM_DATA This field is unused for this command FIRMWARE_VERIFY _AND_INSTALL_RESPONSE 0x86 When a FIRMWARE_VERIFY_AND_INSTALL command request has been unicast to a node that node will send a response in the following format to the source endpoint specified in the requesting frame only if the GPM memory does not contain a valid image If the image is valid the module will reset and begin using the new firmware Field Name Command Specific Description GPM_CMD_ID Should be set to FIRMWARE_VERIFY_AND_INSTALL_RESPONSE 0x86 GPM_STATUS A 1 in the least significant bit indicates the GPM does not contain a valid firmware image All other bits are reserved at this time GPM_BLOCK_NUM This field is unused for this command Set to 0 GPM_START_INDEX This field is unused for this command Set to 0 GPM_NUM_BYTES This field is unused for this command Set to 0 GPM_DATA This field is unused for this command Example To verify a firmware image previously loaded into the GPM on a target radio with serial number of 0x0013a200407402ac a FIRMWARE_VERIFY packet should be formatted as follows spaces added to delineate fields XBee 865 868LP RF Modules 7E 001C 11 01 0013A200407402AC FFFE E6 E6 0023 C105 00 00 05 00 0000 0000 0000 1F Assuming all transmissions
52. This mode passes the local UART data directly to the internal microcontroller allowing for direct communication with the internal microcontroller The only way to exit bypass mode is to reset or power cycle the module If none of the above is true the bootloader will enter Command mode In this mode users can initiate firmware downloads both wired and over the air check application bootloader version strings and enter Bypass mode Application version string Figure 1 shows an Application version string pointer area in application flash which holds the pointer to where the application version string resides The application s linker command file ultimately determines where this string is placed in application flash It is preferable that the application version string be located at address 0x8400 for MC9SO8QE32 parts The application string can be any characters terminated by the NULL character 0x00 There is not a strict limit on the number of characters in the string but for practical purposes should be kept under 100 bytes including the terminating NULL character During an update the bootloader erases the entire application from 0x8400 on The last page has the vector table specifically the redirected reset vector The version string pointer and reset vector are used to determine if the application is valid 2012 Digi International Inc 19 XBee 865 868LP RF Modules Application Interrupt Vector table and Linker Com
53. X CTU a free testing and configuration utility provided by Digi using the radio s serial port interface Firmware can also be updated using the radios RF interface Over the Air Updating The over the air firmware upgrading method provided is a robust and versatile technique which can be tailored to many different networks and applications It has been engineered to be reliable and minimize disruption of normal network operations There are three phases of the over the air upgrade process distributing the new application verifying the new application and installing the new application In the following section the node which will be upgraded will be referred to as the target node The node providing the update information will be referred to as the source node In most applications the source node will be locally attached to a PC running update software Distributing the New Application The first phase of performing an over the air upgrade on a module is transferring the new firmware file to the target node The new firmware image should be loaded in the target node s GPM prior to installation XBee DigiMesh 868 modules use an encrypted binary ebin file for both serial and over the air firmware upgrades These firmware files are available on the Digi Support website The contents of the ebin file should be sent to the target radio using general purpose memory WRITE commands The entire GPM should be erased prior to beginning an upload of
54. XBee 865 868LP RF Modules XBee RF Modules by Digi I nternational Models XBEE S8 Hardware S8 Firmware 8059 q Digi International Inc 11001 Bren Road East Minnetonka MN 55343 877 912 3444 or 952 912 3444 http www digi com 90002126 _B 9 24 2012 XBee 865 868LP RF Modules 2012 Digi International Inc All rights reserved No part of the contents of this manual may be transmitted or reproduced in any form or by any means without the written permission of Digi International Inc XBee is a registered trademark of Digi International Inc Technical Support Phone 866 765 9885 toll free U S A amp Canada 801 765 9885 Worldwide 8 00 am 5 00 pm U S Mountain Time Online Support http www digi com support eservice login jsp Email rf experts digi com 2012 Digi International Inc XBee 800LP RF Modules Contents 1 RF Module Hardware 5 XBee S8 Hardware Description 5 European Acceptance 5 Specifications 6 Serial Communications Specifications 7 UART 7 SPI 7 GPIO Specifications 7 Hardware Specs for Programmable Variant 8 Mechanical Drawings 9 Pin Signals 10 Internal Pin Mappings 11 Design Notes 11 Power Supply Design 11 Recommended Pin Connections 11 Board Layout 11 Module Operation for Programmable Variant 15 XBee Programmable Bootloader 17 Overview 17 Bootloader Software Specifics 17 Bootloader Menu Commands 21 Firmware Updates 22 Output File Configu
55. XBee 865 868LP RF Modules 2012 Digi International Inc Number of Bytes Field Name Description The address with which the radio 8 Destination address should test its link The size of the test packet Maximum k Payload size payload size of 256 bytes The number of packets which should 2 Iterations be sent This should be a number between 1 and 4000 After completing the transmissions of the test link packets the executing radio will send the following data packet to the requesting radio s Test Link Result Cluster 0x0094 on endpoint OxE6 If the requesting radio is configured to operate in API mode then the following information will be output as an API Explicit RX Indicator Frame Number of Bytes Field Name Description MRN The address with which the radio 8 Destination address tested its link The size of the test packet that was 2 Payload size sent to test the link 2 Iterations The numper of packets which were The number of packets successfully 2 Success acknowledged The total number of MAC retries used 2 Retries to transfer all the packets 1 Result 0x00 command was successful 0x03 invalid parameter used 1 RR The maximum number of MAC retries allowed The strongest RSSI reading observed maxRSSI during the test The weakest RSSI reading observed l minRSSI during the test The average RSSI reading observed l avgRSSI during the test Example S
56. _SSEL is de asserted high this output i should be tri stated such that another slave device can drive the line SPI MOSI The SPI master outputs data on this line at the SPI_CLK Master out Slave in 16 ATP6 rate after it selects the desired slave When the module is i configured for SPI operations this pin is an input SPI_SSEL The SPI master outputs a low signal on this line to select Slave Select 15 ATP7 the desired slave When the module is configured for SPI Master out Slave in operations this pin is an input SPI CLK The SPI master outputs a clock on this pin and the rate Clo ck 14 ATP8 must not exceed the maximum allowed 3 5 Mbps When Master out Slave in the module is configured for SPI operations this pin is an input SPI_ATTN The module asserts this pin low when it has data to send to Attention 12 ATP9 the SPI master When this pin is configured for SPI Master in Slave out operations it is an output not tri stated Note By default the inputs have pull up resistors enabled See the PR command to disable the pull up resistors When the SPI pins are not connected but the pins are configured for SPI operation then the pull ups are needed for proper UART operation Full Duplex Operation SPI on XBee requires usage of API mode without escaping to packetize data However by design SPI is a full duplex protocol even when data is only available in one direction This means that whenever data is received
57. a visible location on the OEM product CE Labeling Requirements The CE mark shall consist of the initials CE taking the following form elf the CE marking is reduced or enlarged the proportions given in the above graduated drawing must be respected eThe CE marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus The CE marking must be affixed visibly legibly and indelibly Restrictions According to REC70 03E the following restrictions for radio operation apply Austria Not implemented Planned Georgia Not implemented Greece Limited implementation to 863 865 MHz Norway Not implemented Russian Federation e Limited implementation 864 865 MHz with max e rp 25 mW duty cycle 0 1 or LBT e Forbidden to use at the airports aerodromes Spain Limited implementation to the band 863 865 MHz Sweden Not implemented The Netherlands Not implemented Under study Ukraine Limited implementation 863 865 868 868 6 868 6 868 7 869 2 869 25 MHz Declarations of Conformity Digi has issued Declarations of Conformity for the XBee RF Modules concerning emissions EMC and safety Files can be obtained by contacting Digi Support 2012 Digi International Inc 93 XBee 865 868LP RF Modules Important Note Digi does not list the entire set of standards that must be met for each country Digi customers assume full responsibility for learnin
58. abled by setting the D5 command to 1 enabled by default If enabled the Associate pin is configured as an output and will behave as described in the following sections The Associate pin indicates the synchronization status of a sleep compatible node On a non sleep compatible node the pin functions as a power indicator The following table describes this functionality The LT command can be used to override the blink rate of the Associate pin When set to 0 the device uses the default blink time 500ms for sleep coordinator 250ms otherwise Sleep mode LED Status Meaning 0 On blinking The device is powered and operating properly 1 4 5 Off The device is in a low power mode 1 4 5 On blinking The device is powered awake and is operating properly The network is asleep or the device has not synchronized 7 On solid with the network or has lost synchronization with the network 7 8 On slow blinking 500 ms blink The device is acting as the network sleep coordinator and is i time operating properly 7 8 mS blinking 250 ms blink The device is properly synchronized with the network 8 Off The device is in a low power mode 8 On solid The deviced has not synchronized or has lost synchronization with the network Diagnostics Support The Associate pin works with the commissioning pushbutton to provide additional diagnostic behaviors to aid in deploying and testing a network If the commissioning pu
59. ally or intentionally reset to rapidly re synchronize with the rest of the network If a node which has exited deployment mode receives a sync message from a sleep coordinator which is in deployment mode the sync will be rejected and a corrective sync will be sent to the sleep coordinator Deployment mode can be disabled using the sleep options command SO A sleep coordinator which is not in deployment mode or which has had deployment mode disabled will send a sync message at the beginning of the wake cycle The sleep coordinator will then listen for a neighboring node to relay the sync If the relay is not heard the sync coordinator will send the sync one additional time A node which is not acting as a sleep coordinator which has never been synchronized will send a message requesting sync information at the beginning of its wake cycle Synchronized nodes which receive one of these messages will respond with a synchronization packet Nodes which are configured as non sleep coordinators using the SO command which have gone six or more cycles without hearing a sync will also send a message requesting sync at the beginning of their wake period The following diagram illustrates the synchronization behavior of sleep compatible modules 2012 Digi International Inc 60 XBee 865 868LP RF Modules Enter Deployment Mode Wait Sleep Guard Time Is Node in Deployment Mode Is Sleep Coordinator
60. ameters Changes to the sleep and wake cycle of the network can be made by selecting any node in the network and changing the SP and or ST of the node to values different than those the network is currently using If using a preferred sleep coordinator or if it is known which node is acting as the sleep coordinator it is suggested that this node be used to make changes to network settings If 2012 Digi International Inc 64 XBee 865 868LP RF Modules the network sleep coordinator is not known any node that does not have the non sleep coordinator sleep option bit set see the SO command can be used When changes are made to a node s sleep parameters that node will become the network s sleep coordinator unless it has the non sleep coordinator option selected and will send a sync message with the new sleep settings to the entire network at the beginning of the next wake cycle The network will immediately begin using the new sleep parameters after this sync is sent Changing sleep parameters increases the chances that nodes will lose sync If a node does not receive the sync message with the new sleep settings it will continue to operate on its old settings To minimize the risk of a node losing sync and to facilitate the re syncing of a node that does lose sync the following precautions can be taken 1 Whenever possible avoid changing sleep parameters 2 Enable the missed sync early wake up sleep option SO This c
61. amount of time determined by the RO Packetization Time out parameter If RO 0 packetization begins when a character is received The Command Mode Sequence GT CC GT is received Any character buffered in the serial receive buffer before the sequence is transmitted eThe maximum number of characters that will fit in an RF packet is received See the NP parameter AP Operation API operation is an alternative to transparent operation The frame based API extends the level to which a host application can interact with the networking capabilities of the module When in API mode all data entering and leaving the module is contained in frames that define operations or events within the module Transmit Data Frames received through the serial port include RF Transmit Data Frame Command Frame equivalent to AT commands Receive Data Frames sent out the serial port include RF received data frame Command response Event notifications such as reset etc The API provides alternative means of configuring modules and routing data at the host application layer A host application can send data frames to the module that contain address and payload information instead of using command mode to modify addresses The module will send data frames to the application containing status packets as well as source and payload information from received data packets The API operation option facilitates many operations such as the example
62. an be used as a quick check to determine if 0 OxFFFFFFFF n a a node has been configured as desired EA RF Errors This count is incremented whenever a packet is recieved which contained integrity errors of some sort Once the number reaches OxFFFF further events will not be counted The counter can be reset to any 16 bit value by appending a hexadecimal parameter to the command Good Packets This count is incremented whenever a good frame with a valid MAC header is recieved on the RF interface Once the number reaches OxFFFF further events will not be counted The counter can be reset to any 16 bit value by appending a hexadecimal parameter to the command Transmission Errors This count is incremented whenever a MAC transmission attempt exhausts all MAC retries without ever receiving a MAC acknowledgement message from the destination node Once the number reaches OxFFFF further events will not be counted The counter can be reset to any 16 bit value by appending a hexadecimal parameter to the command Temperature Read module temperature in Celsius Negatives temperatures can be returned Received Signal Strength This command reports the received signal strength of the last received RF data packet The DB command only indicates the signal strength of the last hop It does not provide an accurate quality measurement for a multihop link The DB command value is measured in dBm For example if DB returns 0x60 then the RSSI of the
63. and ST respectively of the network s sleep coordinator These parameters are only used at start up until the node is synchronized with the network When a module has synchronized with the network its sleep and wake times can be queried with the OS and OW commands respectively If D9 1 ON_ SLEEP enabled on a cyclic sleep node the ON_ SLEEP line will assert when the module is awake and de assert when the module is asleep CTS is also de asserted while asleep D7 1 A newly powered unsynchronized sleeping node will poll for a synchronized message and then sleep for the period specified by SP repeating this cycle until it becomes synchronized by receiving a sync message Once a sync message is received the node will synchronize itself with the network Note All nodes in a synchronous sleep network should be configured to operate in either Synchronous Sleep Support Mode or Synchronous Cyclic Sleep Mode Asynchronous sleeping nodes are not compatible with synchronous sleep nodes Asynchronous Sleep Operation Wak Sleeping 2012 Digi International Inc e Timer In cyclic sleep mode SM 4 or SM 5 if serial or RF data is received the module will start a sleep timer time until sleep Any data received serially or by RF link will reset the timer The timer duration can be set using the ST command The module returns to sleep when the sleep timer expires Routers The Sleeping Router feature of DigiMesh makes it possi
64. ble for all nodes in the network to synchronize their sleep and wake times All synchronized cyclic sleep nodes enter and exit a low power state at the same time This forms a cyclic sleeping network Nodes synchronize by receiving a special RF packet called a sync message which is sent by a node acting as a sleep coordinator A node in the network can become a sleep coordinator through a process called nomination The sleep coordinator will send one sync message at the beginning of each wake period The sync message is sent as a broadcast and repeated by every node in the network The sleep and wake times for the entire network can be changed by locally changing the settings on an individual node The network will use the most recently set sleep settings XBee 865 868LP RF Modules Operation One node in a sleeping network acts as the sleeping coordinator The process by which a node becomes a sleep coordinator is described later in this document During normal operations at the beginning of a wake cycle the sleep coordinator will send a sync message as a broadcast to all nodes in the network This message contains synchronization information and the wake and sleep times for the current cycle All cyclic sleep nodes receiving a sync message will remain awake for the wake time and then sleep for the sleep period specified The sleep coordinator will send one sync message at the beginning of each cycle with the currently configured wake and sle
65. cation When the entire ebin file has been uploaded to the GPM of the target node a FIRMWARE_VERIFY_AND_INSTALL command can be issued Once the target receives the command it will verify the ebin file loaded in the GPM If it is found to be valid then the module will install the new firmware This installation process can take up to 8 seconds During the installation the module will be unresponsive to both serial and RF communication To complete the installation the target module will reset AT parameter settings which have not been written to flash using the WR command will be lost Things to Remember 2012 Digi International Inc e The firmware upgrade process requires that the module resets itself Because of this reset parameters which have not been written to flash will be lost after the reset To avoid this write all parameters with the WR command before doing a firmware upgrade Packet routing information will also be lost after this reset Route discoveries will be necessary for DigiMesh unicasts involving the upgraded node as a source destination or intermediate node e Because explicit API Tx frames can be addressed to a local node accessible via the SPI or UART or a remote node accessible over the RF port the same process can be used to update firmware on a module in either case QO No XBee 865 868LP RF Moduless 4 Networking Methods Directed Broadcast Repeater Mode In this broadcast mode the
66. command the CTS pin will assert low when the module wakes and can receive serial data and de assert high when the module sleeps Asynchronous Cyclic Sleep with Pin Wake Up Mode SM 5 SM 5 is a slight variation on SM 4 that allows the module to be woken prematurely by asserting the Sleep_RQ pin pin 9 In SM 5 the XBee can wake after the sleep period expires or if a high to low transition occurs on the Sleep_ RQ pin 2012 Digi International Inc 58 XBee 865 868LP RF Modu les Synchronous Sleep Support Mode SM 7 A node in synchronous sleep support mode will synchronize itself with a sleeping network but will not itself sleep At any time the node will respond to new nodes which are attempting to join the sleeping network with a sync message Asleep support node will only transmit normal data when the other nodes in the sleeping network are awake Sleep support nodes are especially useful when used as preferred sleep coordinator nodes and as aids in adding new nodes to a sleeping network Note Because sleep support nodes do not sleep they should be mains powered Synchronous Cyclic Sleep Mode SM 8 A node in synchronous cyclic sleep mode sleeps for a programmed time wakes in unison with other nodes exchanges data and sync messages and then returns to sleep While asleep it cannot receive RF messages or read commands fromt the UART port Generally sleep and wake times are specified by the SP
67. command does not work with synchronous sleep Missed Sync Count SQ Count of the number of syncs that have been missed This value can be reset by setting n a n a ATSQ to 0 When the value reaches OxFFFF it will not be incremented anymore 2012 Digi International Inc 75 XBee 865 868LP RF Modules AT Command Name and Description Sleep Status The SS command can be used to query a number of Boolean values describing the status of the module Bit 0 This bit will be true when the network is in its wake state Bit 1 This bit will be true if the node is currently acting as a network sleep coordinator Bit 2 This bit will be true if the node has ever received a valid sync message since the time it was powered on Bit A This bit will be true if the node has received a sync message in the current wake cycle Bit 4 This bit will be true if the user has altered the sleep settings on the module so that the node will nominate itself and send a sync message with the new settings at the beginning of the next wake cycle Bit 5 This bit will be true if the user has requested that the node nominate itself as the sleep coordinator using the commissioning button or the CB2 command All omer bits Reserved All non documented bits can be any value and should be ignored bit 6 This bit will be true if the node is currently in deployment mode All other bits Reserved All non documented bits can be any value and
68. d Software prior to version 8x60 did not include RSSI information 0x80 Response is a remote command The value of the required register OxFF the 8 bit sum of bytes from offset 3 to this byte Example If a remote command is sent to a remote device with 64 bit address 0x0013A200 40522BAA to query the SL command and if the frame D 0x55 the response would look like the above example 2012 Digi International Inc 92 Appendix A Agency Certifications Europe ETSI The XBee RF Modules excluding the PRO have been certified for use in several European countries For a complete list refer to www digi com If the XBee RF Modules are incorporated into a product the manufacturer must ensure compliance of the final product to the European harmonized EMC and low voltage safety standards A Declaration of Conformity must be issued for each of these standards and kept on file as described in Annex II of the R amp TTE Directive Furthermore the manufacturer must maintain a copy of the XBee user manual documentation and ensure the final product does not exceed the specified power ratings antenna specifications and or installation requirements as specified in the user manual If any of these specifications are exceeded in the final product a submission must be made to a notified body for compliance testing to all required standards OEM Labeling Requirements The CE marking must be affixed to
69. d The 865 868LP supports an external clock rate of up to 3 5 Mbps Data is transmitted and received with most significant bit first using SPI mode 0 This means the CPOL and CPHA are both 0 Mode 0 was chosen because it s the typical default for most microcontrollers and would simplify configuration of the master Further information on Mode 0 is not included in this manual but is well documented on the internet SPI Signals The official specification for SPI includes the four signals SPI_MI SO SPI_MOSI SPI_CLK and SPI_SSEL Using only these four signals the master cannot know when the slave needs to send and the SPI slave cannot transmit unless enabled by the master For this reason the SPI_ ATTN signal is available in the design This allows the module to alert the SPI master that it has data to send In turn the SPI master is expected to assert SPI_SSEL and start SPI_ CLK unless these signals are already asserted and active respectively This in turn allows the XBee module to send data to the master The table below names the SPI signals and specifies their pinouts It also describes the operation of each pin 2012 Digi International Inc 26 XBee 865 868LP RF Modules Applicable AT Command Signal Name Pin Number Description When SPI_SSEL is asserted low and SPI_CLK is active SPI MISO the module outputs the data on this line at the SPI_CLK Master in Slave out 17 ATP5 rate When SPI
70. dBi antenna up to 46 ft 14 m w Indoor Urban Range embedded antenna Outdoor RF line of sight up to 5 2 miles 8 4 km w 2 1dB dipole antenna up to 0 4 mi Range 640 m w embedded antenna Transmit Power Output 12 dBm 16 mW RF Data Rate High 80 kbps RF Data Rate Low 10 kbps Serial UART interface CMOS Serial UART baud rate stability of lt 1 Serial Interface Data Rate software selectable 3000 ee alba Receiver Sensitivity typical 101 dBm high data rate 106 dBm low data rate Frequency offset Data rate Receiver Blocking typical 400 kHz 40 dB 35 dB 200 kHz 35 dB 29 dB Power Requirements Supply Voltage 2 7 to 3 6 VDC Transmit Current high data rate 48mA 45 mA typical Transmit Current low data rate 47 mA 41 mA typical Idle Receive Current high data rate 27mA 22 mA typical Idle Receive Current low data rate 26 mA 24 mA typical Sleep Current 1 7 pA General Operating Frequency Band 863 to 870 MHz Dimensions 0 866 in x 1 333 in x 1 2 in 2 119 cm x 3 4 cm x 0 305 cm Weight 14 oz 4 9 Operating Temperature 40 to 85 C industrial Pad on module edge U FL RF connector embedded Antenna Options antenna 13 I O lines 5 dedicated to SPI that can be used as digital Digital 1 0 outputs ADC 6 10 bit analog inputs Networking amp Security Supported Network Topologies M
71. diagnostics API frames can provide indication of IO samples from remote devices and node identification messages Remote Configuration Set read configuration commands can be sent to remote devices to configure them as needed using the API As a general rule of thumb API mode is recommended when a device e sends RF data to multiple destinations e sends remote configuration commands to manage devices in the network e receives RF data packets from multiple devices and the application needs to know which device sent which packet e must support multiple endpoints cluster IDs and or profile IDs e uses the Device Profile services API mode is required when e receiving I O samples from remote devices e using SPI for the serial port If the above conditions do not apply e g a sensor node router or a simple application then transparent operation might be suitable It is acceptable to use a mixture of devices running API mode and transparent mode in a network Modes of Operation Description of Modes When not transmitting data the RF module is in Receive Mode The module shifts into the other modes of operation under the following conditions Transmit Mode Serial data in the serial receive buffer is ready to be packetized Sleep Mode Command Mode Command Mode Sequence is issued not available when using the SPI port Transmit Mode When serial data is received and is ready for packe
72. ding on the source of the command received via Over the Air or local UART the download will proceed via wired or over the air respectively Adjust Timeout for Update Firmware T The T command changes the timeout before sending a NAK by Base Time 2 T The Base Time for the local UART is different than the Base Time for Over the Air During a firmware update the bootloader will automatically increase the Timeout if repeat packets are received or multiple NAKs for the same packet without success occur Application Version String A The A command provides the version of the currently loaded application If no application is present Unkown will be returned Bootloader Version String V The V command provides the version of the currently loaded bootloader The version will return a string in the format BLFFF HHH XYZ_DDD where FFF represents the Flash size in kilo bytes HHH is the hardware XYZ is the version and DDD is the preferred XMODEM packet size for updates Double the preferred packet size is also possible but not guaranteed For example BLO32 2B0 023 064 will take 64 byte CRC XMODEM payloads and may take 128 byte CRC XMODEM payloads also In this case both 64 and 128 payloads are handled but the 64 byte payload is preferred for better Over the Air reliability Bootloader Version BLO32 2x0 025_ 064 only operates at 9600 baud on the local UART as well as communications to the internal microcontroller
73. e to establish seniority among the multiple sleep coordinators Seniority is determined by four factors in order of priority 1 Newer sleep parameters a node using newer sleep parameters SP ST is considered senior to a node using older sleep parameters See the Changing Sleep Parameters section below 2 Preferred Sleep Coordinator a node acting as a preferred sleep coordinator is senior to other nodes 3 Sleep Support Node sleep support nodes are senior to cyclic sleep nodes This behavior can be modified using the SO parameter 4 Serial number in the event that the above factors do not resolve seniority the node with the higher serial number is considered senior Commissioning Button The commissioning button can be used to select a module to act as the sleep coordinator If the commissioning button functionality has been enabled a node can be immediately nominated as a sleep coordinator by pressing the commissioning button twice or by issuing the CB2 command A node nominated in this manner is still subject to the election process described above A node configured as a non sleep coordinator will ignore commissioning button nomination requests Changing Sleep Parameters Any sleep compatible node in the network which does not have the non sleep coordinator sleep option set can be used to make changes to the network s sleep and wake times If a node s SP and or ST are changed to values different from those that the network
74. ection XXXXX These commands check if the General Purpose Memory contains a valid over the 49 XBee 865 868LP RF Modules 2012 Digi International Inc air update file For the FIRMWARE_VERIFY_AND_INSTALL command if the GPM contains a valid firmware image then the module will reset and begin using the new firmware Field Name Command Specific Description Should be set to FIRMWARE_VERIFY 0x05 or GPM_CMD _ID FIRMWARE_VERIFY_AND_INSTALL 0x06 GPM_OPTIONS There are currently no options defined for this command Set this field to 0 GPM_BLOCK_NUM This field is unused for this command Set to 0 GPM_START_INDEX This field is unused for this command Set to 0 GPM_NUM_BYTES This field is unused for this command Set to 0 GPM_DATA This field is unused for this command FIRMWARE_VERIFY _ RESPONSE 0x85 When a FIRMWARE_VERIFY command request has been unicast to a node that node will send a response in the following format to the source endpoint specified in the requesting frame Field Name Command Specific Description GPM_CMD_ID Should be set to FIRMWARE_VERIFY_RESPONSE 0x85 A 1 in the least significant bit indicates the GPM does not contain a GPM_STATUS valid firmware image A 0 in the least significant bit indicates the GPM does contain a valid firmware image All other bits are reserved at this time GPM_BLOCK_NUM This field is unused for this command Set to 0 GPM_STAR
75. ee 15 O oe R Associat N e and an LED can be connected to module pins 20 and 15 respectively to support the commissioning pushbutton and associated LED functionalities Commissioning Pushbutton The commissioning pushbutton definitions provide a variety of simple functions to aid in deploying devices in a network The commissioning button functionality on pin 20 is enabled by setting the DO command to 1 enabled by default Sleep Button Presses Configuration and Action Sync Status 2012 Digi International Inc Immediately sends a Node Identification broadcast transmission All devices that receive this transmission will 1 Not configured for sleep blink their Associate LED rapidly for 1 second All API devices that receive this transmission will send a Node Identification frame out their UART API ID 0x95 Wakes the module for 30 seconds Immediately sends a Node Identification broadcast transmission All devices that receive this 1 Configured for asynchronous sleep transmission will blink their Associate LED rapidly for 1 second All API devices that receive this transmission will send a Node Identification frame out their UART API ID 0x95 Wakes the module for 30 seconds or until the entire module goes to sleep Queues a Node Identification broadcast transmission to be sent at the beginning of the next network wake cycle 1 Configured for synchronous sleep All devices that receive this transmission will
76. egister If no characters present register is queried Checksum 8 Ox0F OxFF the 8 bit sum of bytes from offset 3 to this byte The above example illustrates an AT command when querying an NH value AT Command Queue Parameter Value Frame Type 0x09 This API type allows module parameters to be queried or set In contrast to the AT Command API type new parameter values are queued and not applied until either the AT Command 0x08 API type or the AC Apply Changes command is issued Register queries reading parameter values are returned immediately Example Send a command to change the baud rate BD to 115200 baud but don t apply changes yet Module will continue to operate at the previous baud rate until changes are applied Start Delimiter Number of bytes between the length and the checksum Identifies the UART data frame for the host to correlate with a subsequent ACK acknowledgement If set to 0 no response is sent Frame specific Data Command Name Two ASCII characters that identify the AT Command If present indicates the requested parameter value to set the given register If no characters present register is queried Checksum OxFF the 8 bit sum of bytes from offset 3 to this byte Note In this example the parameter could have been sent as a zero padded 2 byte or 4 byte value Transmit Request Frame Type 0x10 A Transmit Request API frame causes the
77. ep times All router nodes which receive this sync message will relay the message to the rest of the network If the sleep coordinator does not hear a re broadcast of the sync message by one of its immediate neighbors then it will re send the message one additional time It should be noted that if SP or ST are changed the network will not apply the new settings until the beginning of the next wake time See the Changing Sleep Parameters section below for more information A sleeping router network is robust enough that an individual node can go several cycles without receiving a sync message due to RF interference for example As a node misses sync messages the time available for transmitting messages in the wake time is reduced to maintain synchronization accuracy By default a module will also reduce its active sleep time progressively as sync messages are missed Synchronization Messages A sleep coordinator will regularly send sync messages to keep the network in sync Nodes which have not been synchronized or in some cases which have lost sync will also send messages requesting sync information Deployment mode is used by sleep compatible nodes when they are first powered up and the sync message has not been relayed A sleep coordinator in deployment mode will rapidly send sync messages until it receives a relay of one of those messages This allows a network to be deployed more effectively and allows a sleep coordinator which is accident
78. er the air f The host module will begin receiving C characters indicating that the remote module is requesting an Xmodem CRC transfer Using XCTU or another terminal program Select XMODEM file transfer Select the Binary file to upload transfer Click Send to start the transfer At the con clusion of a successful transfer the bootloader will jump to the newly loaded application Output File Configuration BKGD Programming P amp E Micro provides a background debug tool that allows flashing applications on the MC9SO8QE parts through their background debug mode port By default the Codewarrior tool produces an ABS output file for use in programming parts through the background debug interface The programmable XBee from the factory has the BKGD debugging capability disabled In order to debug a bootloader 2012 Digi International Inc 22 XBee 865 868LP RF Modules with the debug interface enabled needs to be loaded on the secondary processor or a stand alone app needs to be loaded Bootloader updates The supplied bootloader requires files in a flat binary format which differs from the default ABS file produced The Codewarrior tool also produces a 19 output file In order to successfully flash new applications the S19 file must be converted into the flat binary format Utilities are available on the web that will convert S19 output to BIN outputs Often times the BIN file conversion will pad the addresses
79. erized as either asynchronous SM 1 4 5 or synchronous SM 7 8 Asynchronous sleeping modes should not be used in a synchronous sleeping network and vice versa Asynchronous sleep modes can be used to control the sleep state on a module by module basis Modules operating in an asynchronous sleep mode should not be used to route data Digi strongly encourages users to set asynchro nous sleeping modules as end devices using the CE command This will prevent the node from attempting to route data The synchronous sleep feature of DigiMesh makes it possible for all nodes in the network to synchronize their sleep and wake times All synchronized cyclic sleep nodes enter and exit a low power state at the same time This forms a cyclic sleeping network Nodes synchronize by receiving a special RF packet called a sync message which is sent by a node acting as a sleep coordinator A node in the network can become a coordinator through a process called nomination The sleep coordinator will send one sync message at the beginning of each wake period The sync message is sent as a broadcast and repeated by every node in the network The sleep and wake times for the entire network can be changed by locally changing the settings on an individual node The network will use the most recently set sleep settings Sleep Modes Normal Mode SM 0 Normal mode is the default for a newly powered on node In this mode a node will not sleep Normal mode nodes sho
80. ert RTS for long periods of time to avoid filling the serial transmit buffer If an RF data packet is received and the serial transmit buffer does not have enough space for all of the data bytes the entire RF data packet will be discarded The UART Data Present Indicator is a useful feature when using RTS flow control When enabled the DIO19 line asserts when UART data is queued to be transmitted from the module See the P9 command in the Command Reference Tables for more information Note If the XBee is sending data out the UART when RTS is de asserted set high the XBee could send up to 5 characters out the UART or SPI port after RTS is de asserted 2012 Digi International Inc 29 XBee 865 868LP RF Modules Serial I nterface Protocols The XBee modules support both transparent and API Application Programming Interface serial interfaces Transparent Operation UART When operating in transparent mode the modules act as a Serial line replacement All UART data received through the DIN pin is queued up for RF transmission When RF data is received the data is sent out through the serial port The module configuration parameters are configured using the AT command mode interface Please note that transparent operation is not provided when using the SPI Data is buffered in the serial receive buffer until one of the following causes the data to be packetized and transmitted No serial characters are received for the
81. es in such a connection can be released when no longer needed Switched Using circuit switching or packet switching technologies a point to point circuit can be set up dynamically and dropped when no longer needed DigiMesh Networking Mesh networking allows messages to be routed through several different nodes to a final destination DigiMesh firmware allows manufacturers and system integrators to bolster their networks with the self healing attributes of mesh networking In the event that one RF connection between nodes is lost due to power loss environmental obstructions etc critical data can still reach its destination due to the mesh networking capabilities embedded inside the modules DigiMesh Feature Set DigiMesh contains the following features e Self healing Any node may enter or leave the network at any time without causing the network as a whole to fail e Peer to peer architecture No hierarchy and no parent child relationships are needed Quiet Protocol Routing overhead will be reduced by using a reactive protocol similar to AODV e Route Discovery Rather than maintaining a network map routes will be discovered and created only when needed e Selective acknowledgements Only the destination node will reply to route requests e Reliable delivery Reliable delivery of data is accomplished by means of acknowledgements Sleep Modes Low power sleep modes with synchronized wake are supported with variable sleep and wake t
82. esh point to point point to multipoint peer to peer Number of Channels user selectable channels 30 channels LBT AFA 2012 Digi International Inc XBee 865 868LP RF Modules Specifications of the XBee 865 868LP RF Module Specification XBee Addressing Options PAN ID and 64 bit addresses Encryption 128 bit AES Agency Approvals Europe CE CE Marking To determine your range perform a range test under your operating conditions Please see the list of channel limits for countries in the European Community in this User Manual Serial Communications Specifications XBee RF modules support both UART Universal Asynchronous Receiver Transmitter and SPI Serial Peripheral Interface serial connections UART UART Pin Assignments UART Pins Module Pin Number DOUT DIN CONFIG CTS DIO7 RTS DIO6 More information on UART operation is found in the UART section in Chapter 2 SPI SPI Pin Assignments SPI Pins Module Pin Number SPI_SCLK DIO18 SPI_SSEL DIO17 SPI_MOSI DIO16 SPI_MISO DIO15 For more information on SPI operation see the SPI section in Chapter 2 GPIO Specifications XBee RF modules have 15 GPIO General Purpose Input Output ports available The exact list will depend on the module configuration as some GPIO pads are used for purposes such as serial communication See GPIO section for more information on c
83. f a DigiMesh unicast by the intermediate nodes When a unicast is sent with the Trace Route API option enabled the unicast is sent to its destination radios which forward the unicast to its eventual destination will transmit a Route Information RI packet back along the route to the unicast originator A full description of Route Information API packets can be found in the API section of this manual In general they contain addressing information for the unicast and the intermediate hop for which the trace route packet was generated RSSI information and other link quality information Example Suppose that a data packet with trace route enabled was successfully unicast from radio A to radio E through radios B C and D The following sequence would occur e After the successful MAC transmission of the data packet from A to B A would output a RI Packet indicating that the transmission of the data packet from A to E was successfully for warded one hop from A to B e After the successful MAC transmission of the data packet from B to C B would transmit a RI Packet to A A would output this RI packet out its UART upon reception e After the successful MAC transmission of the data packet from C to D C would transmit a RI Packet to A through B A would output this RI packet out its UART upon reception e After the successful MAC transmission of the data packet from D to E D would transmit a RI Packet to A through C and B A would output
84. fault configuration on the UART at 9600 baud and it will bring up the module in command mode on the UART port Appropriate commands can then be sent to the module to configure it for UART operation If those parameters are written then the module will come up with the UART enabled as desired on the next reset Data Format The SPI will only operate in API mode 1 Neither transparent mode nor API mode 2 which escapes control characters will be supported This means that the AP configuration only applies to the UART and will be ignored while using the SPI SPI Parameters Most host processors with SPI hardware allow the bit order clock phase and polarity to be set For communication with all XBee radios the host processor must set these options as follows Bit Order send MSB first Clock Phase CPHA sample data on first leading edge Clock Polarity CPOL first leading edge rises 2012 Digi International Inc 28 XBee 865 868LP RF Modules This is SPI Mode 0 and MSB first for all XBee radios Mode 0 means that data is sampled on the leading edge and that the leading edge rises MSB first means that bit 7 is the first bit of a byte sent over the interface Serial Buffers To enable the UART port DIN and DOUT must be configured as peripherals To enable the SPI port SPI_ MISO SPI_MOSI SPI_SSEL and SPI_CLK must be enabled as peripherals If both ports are enabled then output will go to the UART until the first inp
85. g and meeting the required guidelines for each country in their distribution market For more information relating to European compliance of an OEM product incorporating the XBee RF Module contact Digi or refer to the following web site www cept org Search for short range device regulations XBee RF Module The following antennas have been tested and approved for use with the embedded XBee RF Module dipole 2 1 dBi digi PN AO8 HABUF P5I PCB antenna 9 dBi which is included in the module 2012 Digi International Inc 94 Appendix B Migrating from XBee to SMT Modules The XBee 865 868 LP modules are designed to be compatible with the XBee through hole modules The SMT modules have all the features of the through hole modules and offer the increased feature set described in this user s guide Pin Mapping Mapping of the XBee SMT module pins to the XBee through hole pins is shown in the following table SMT Pin Through Hole Pin 1 GND 2 VCC 1 3 DOUT DIO13 4 DIN CONFIG DIO14 5 DIO12 6 7 8 2 3 4 RESET 5 RSSI PWM DIO10 6 7 8 9 PWM1 DIO11 reserved DTR SLEEP_RQ DIO8 GND 10 SPI_ATTN DIO19 GND SPI_CLK DIO18 SPI_SSEL DIO17 SPI_MOSI DIO16 SPI_MISO DIO15 reserved reserved reserved reserved GND reserved DIO4 CTS DIO7 ON SLEEP DIO9 VREF ASSOCIATE DIOS RTS DIO6
86. he Duty Cycle requirement imposed by ETSI LBT AFA requires that at least two frequencies be used for transmission The g band mode contains several sub bands Refer to Chapter 1 for a full list of channels and frequencies The advantage of this feature is that it gives a level of fairness to the radios in a given area Before this radio transmits it will sense a channel to determine if there is activity by taking an RSSI measurement for 5ms If the measurement is below the threshold then the radio will transmit on that channel If there is activity then that channel will not be used and the radio will listen for at least 5ms to allow transmissions to be received After the radio transmits on a channel it will not transmit on that channel again until the minimum TX off time has been met which is greater than 100ms For this reason it is useful to have many channels so transmissions are not delayed There is also an ETSI requirement that only 100 seconds of transmission may occur over the period of an hour on 200kHz of spectrum This method simplifies and optimizes the calculations of spectrum use over the period of one hour As the ETSI specification states the more channels you have the more transmission time you have in a one hour period The effective duty cycle can be calculated based on the number of available channels enabled as follows Effective Duty Cycle number of channels 100 3600 2012 Digi International Inc 24 XBee
87. he baud rate will not change the actual baud rate until changes are applied Changes can be applied in one of the following ways The AC Apply Changes command is issued AT command mode is exited To Exit AT Command Mode 1 Send the ATCN Exit Command Mode command followed by a carriage return OR 2 If no valid AT Commands are received within the time specified by CT Command Mode Timeout Command the RF module automatically returns to Idle Mode For an example of programming the RF module using AT Commands and descriptions of each configurable parameter please see the Command Reference Table chapter Sleep Mode Sleep modes allow the RF module to enter states of low power consumption when not in use XBee RF modules support both pin sleep sleep mode entered on pin transition and cyclic sleep module sleeps for a fixed time XBee sleep modes are discussed in detail in chapter 5 2012 Digi International Inc 34 3 Advanced Application Features Remote Configuration Commands A module in API mode has provisions to send configuration commands to remote devices using the Remote Command Request API frame See API Operations chapter This API frame can be used to send commands to a remote module to read or set command parameters Sending a Remote Command To send a remote command the Remote Command Request frame should be populated with the 64 bit address of the remote device the correct command options
88. he process of Example 2 above can be used To update the DH DL registers of the network then the method of Example 3 below can be used Example 3 The module with serial number 0x0013a2004052c507 was being used as a network aggregator It was replaced with a module with serial number 0x0013a200f5e4d3b2 The AG0013a2004052c507 command should be issued on the new module This will cause all modules which had a DH DL register setting of 0x0013a2004052c507 to update their DH DL register setting to the MAC address of the sending module 0x0013a200f5e4d3b2 XBee 865 868LP RF Modules Device Placement For a network installation to be successful the installer must be able to determine where to place individual XBee devices to establish reliable links throughout the network Link Testing A good way to measure the performance of a network is to send unicast data through the network from one device to another to determine the success rate of many transmissions To simplify link testing the modules support a loopback cluster ID 0x12 on the data endpoint OxE8 Any data sent to this cluster ID on the data endpoint will be transmitted back to the sender The configuration steps to send data to the loopback cluster ID depend on the AP setting AT Configuration AP 0 To send data to the loopback cluster ID on the data endpoint of a remote device set the Cl command value to 0x12 The SE and DE commands should be set to OxE8 default value
89. hich DH and DL were previously set Checksum 21 Ox2E OxFF the 8 bit sum of bytes from offset 3 to this byte Example In the above example a radio which had a destination address DH DL of 0x0013A2004052AAAA updated its destination address to 0x0013A2004052BBBB 2012 Digi International Inc 88 XBee 865 868LP RF Modules Receive Packet Frame Type 0x90 When the module receives an RF packet it is sent out the UART using this message type Number of bytes between the length and the checksum Identifies the UART data frame for the host to correlate with a subsequent ACK acknowledgement If set to 0 no response is sent 64 bit address of sender Reserved 0x01 Packet Acknowledged 0x02 Packet was a broadcast packet Received RF data OxFF the 8 bit sum of bytes from offset 3 to this byte Example In the above example a device with a 64 bit address of 0x0013A200 40522BAA sends a unicast data transmission to a remote device with payload RxData If AO 0 on the receiving device it would send the above frame out its UART 2012 Digi International Inc 89 XBee 865 868LP RF Modules Explicit Rx Indicator Frame Type 0x91 When the modem receives an RF packet it is sent out the UART using this message type when AO 1 Number of bytes between the length and the checksum 64 b
90. iMesh routing on this node When set this node will not propagate broadcasts or become and intermediate node in a route bit 2 Indirect messaging polling enable Periodically send requests for messages held by the node s coordinator Supported in both firmware variants 2012 Digi International Inc 67 XBee 865 868LP RF Modules Addressing Commands AT Command AG TO Name and Description Aggregator Support The AG command sends a broadcast through the network that has the following affects on nodes which receive the broadcast e The receiving node will establish a DigiMesh route back to the originating node provided there is space in the routing table e The DH and the DL of the receiving node will be updated to the address of the originating node if the AG parameter matches the current DH DL of the receiving node e For API enabled modules on which DH and DL are updated an Aggregate Addressing Update API frame will be sent out the serial port Note that the AG command is only available on products which support DigiMesh Transmit Options This command defines transmission options for all packets originating from this radio These options can be overridden on a packet by packet basis by using the TxOptions field of the API TxRequest frames Bit Meaning Description 6 7 Delivery method _b 00 lt invalid option b 01 Point Multipoint b 10 Repeater mode directed broadcast of
91. ice Configuration 54 Network ID 54 Data Transmission and Routing 54 Unicast Addressing 54 Broadcast Addressing 54 Routing 54 Route Discovery 54 Throughput 55 Transmission Timeouts 55 Unicast One Hop Time 55 Transmitting a broadcast 55 Transmitting a unicast with a known route 56 Ww XBee 800LP RF Modules Contents Transmitting a unicast with an unknown route 57 95 Transmitting a unicast with a broken route 57 Appendix J Manufacturing Information 98 5 Sleep Mode 58 Sleep Modes 58 Normal Mode SM 0 58 Asynchronous Pin Sleep Mode SM 1 58 Asynchronous Cyclic Sleep Mode SM 4 58 Asynchronous Cyclic Sleep with Pin Wake Up Mode SM 5 58 Synchronous Sleep Support Mode SM 7 59 Synchronous Cyclic Sleep Mode SM 8 59 Asynchronous Sleep Operation 59 Wake Timer 59 Sleeping Routers 59 Operation 60 Becoming a Sleep Coordinator 62 Configuration 63 Diagnostics 66 6 Command Reference Tables 67 7 API Operation 77 API Frame Specifications 77 API UART Exchanges 79 AT Commands 79 Transmitting and Receiving RF Data 79 Remote AT Commands 79 Supporting the API 80 Frame Data 80 AT Command 80 AT Command Queue Parameter Value 81 Transmit Request 81 Explicit Addressing Command Frame 82 Remote AT Command Request 84 AT Command Response 85 Modem Status 85 Transmit Status 86 Route Information Packet 86 Aggregate Addressing Update 88 Receive Packet 89 Explicit Rx Indicator 90 Node Identification Indicator 91 Rem
92. imes 2012 Digi International Inc On Qo XBee 865 868LP RF Moduless Networking Concepts Device Configuration DigiMesh modules can be configured to act as routers or end devices with the CE command By default all modules in a DigiMesh network act as routers Modules configured as routers will actively relay network unicast and broadcast traffic as described below Network ID DigiMesh networks are defined with a unique network identifier This identifier is set with the ID command For modules to communicate they must be configured with the same network identifier The ID parameter allows multiple DigiMesh networks to co exist on the same physical channel Data Transmission and Routing Unicast Addressing When transmitting while using Unicast communications reliable delivery of data is accomplished using retries and acknowledgements The number of retries is determined by the NR Network Retries parameter RF data packets are sent up to NR 1 times and ACKs acknowledgements are transmitted by the receiving node upon receipt If a network ACK is not received within the time it would take for a packet to traverse the network twice a retransmission occurs To send Unicast messages set the DH and DL on the transmitting module to match the corresponding SH and SL parameter values on the receiving module Broadcast Addressing Broadcast transmissions will be received and repeated by all routers in the network Because A
93. ion Configure options for the DIO7 line of the module Options include 0 Input unmonitored 1 CTS flow control 3 Digital input monitored 4 Digital output low 5 Digital output high 6 RS 485 Tx enable low TX OV on transmit high when idle 7 RS 485 Tx enable high TX high on transmit OV when idle D7 0 1 3 7 DIO6 Configuration Configure options for the DIO6 line of the module Options include 0 Input unmonitored 1 RTS flow control 3 Digital input monitored 4 Digital output low 5 Digital output high D6 0 1 3 5 I O Commands T O Commands AT Command Name and Description DIO10 PWMO0 Configuration Configure options for the DIO10 PWM0 line of the module Options include 0 Input unmonitored 1 RSSI PWM 2 PWMO 3 Digital input monitored 4 Digital output low 5 Digital output high PO Parameter Range 0 5 Default DIO11 PWM1 Configuration Configure options for the DIO11 PWM1 line of the module Options include 0 Input unmonitored P1 2 PWM1 3 Digital input monitored 4 Digital output low 5 Digital output high 2012 Digi International Inc 69 XBee 865 868LP RF Modules T O Commands AT Command P2 Name and Description DIO12 Configuration Configure options for the DIO12 line of the module Options include 0 Input unmonitored 3 Digital input monitored 4 Dig
94. ion the message is addressed to Cluster ID the packet was addressed to Profile ID the packet was addressed to 0x01 Packet Acknowledged 0x02 Packet was a broadcast packet Received RF data OxFF the 8 bit sum of bytes from offset 3 to this byte Example If the commissioning push button is pressed on a remote router device with 64 bit address 0x0013a200407402ac and default NI string the following node identification indicator would be received 0x7e 0025 9500 13a2 0040 7402 acff fec2 fffe 0013 a200 4074 O2ac 2000 fffe 0101 c105 101e 000c 0000 2e33 2012 Digi International Inc 91 XBee 865 868LP RF Modules Remote Command Response Frame Type 0x97 If a module receives a remote command response RF data frame in response to a Remote AT Command Request the module will send a Remote AT Command Response message out the UART Some commands may send back multiple frames for example Node Discover ND command Number of bytes between the length and the checksum This is the same value passed in to the request The address of the remote radio returning this response Reserved Name of the command The least significan nibble indicates the command status 0 OK 1 ERROR 2 Invalid Command 3 Invalid Parameter The most significant nibble is a bitfield as follows 0x40 The RSSI field is invalid and should be ignore
95. ished with horizontal line over signal name CMOS Logic 2 8 3 4V a CMOS Logic 2 8 3 4V daa NT s DIN data in 7 DIN data in XBee XBee gt shells Module Module Serial Data Data enters the module UART through the DIN pin 4 as an asynchronous serial signal The signal should idle high when no data is being transmitted Each data byte consists of a start bit low 8 data bits least significant bit first and a stop bit high The following figure illustrates the serial bit pattern of data passing through the module UART data packet 0x1F decimal number 31 as transmitted through the RF module Example Data Format is 8 N 1 bits parity of stop bits Least Significant Bit first aa 1 Idle high 4 4 4 LGF N UART Signal A Signal o voc Voltage A i L Start Bit low Stop Bit high Time __ gt Serial communications depend on the two UARTs the microcontroller s and the RF module s to be configured with compatible settings baud rate parity start bits stop bits data bits The UART baud rate parity and stop bits settings on the XBee module can be configured with the BD NB and SB commands respectively See the command table in chapter 10 for details bo Sn 2012 Digi International Inc XBee 865 868LP RF Modules SPI Communications The XBee modules support SPI communications in slave mode Slave mode receives the clock signal and data from the master and returns data to
96. it address of sender Reserved Endpoint of the source that initiated the transmission Endpoint of the destination the message is addressed to Cluster ID the packet was addressed to Profile ID the packet was addressed to 0x01 Packet Acknowledged 0x02 Packet was a broadcast packet Received RF data OxFF the 8 bit sum of bytes from offset 3 to this byte Example In the above example a device with a 64 bit address of 0x0013A200 40522BAA sends a broadcast data transmission to a remote device with payload RxData Suppose the transmission was sent with source and destination endpoints of OxEO cluster D 0x2211 and profile D 0xC105 If AO 1 on the receiving device it would send the above frame out its UART 2012 Digi International Inc 90 XBee 865 868LP RF Modules Node Identification ndicator Frame Type 0x95 This frame is received when a module transmits a node identification message to identify itself when AO 0 The data portion of this frame is similar to a network discovery response frame see ND command Number of bytes between the length and the checksum 64 bit address of sender Reserved 0x01 Packet Acknowledged 0x02 Packet was a broadcast packet 0x40 Point multipoint packet 0x80 Directed broadcast packet 0xC0 DigiMesh packet Reserved Endpoint of the destinat
97. ital output low 5 Digital output high Parameter Range 0 3 5 Default RP DO D1 D2 D3 D4 D5 RSSI PWM Timer Time RSSI signal will be output after last transmission When RP OxFF output will always be on ADO0 DI00 Configuration Configure options for the ADO DIO0 line of the module Options include 0 Input unmonitored 1 Commissioning button enable 2 Analog Input 3 Digital input monitored 4 Digital output low 5 Digital output high AD1 DI01 Configuration Configure options for the AD1 DIO1 line of the module Options include 0 Input unmonitored 2 Analog Input 3 Digital input monitored 4 Digital output low 5 Digital output high AD2 DI02 Configuration Configure options for the AD2 DIO2 line of the module Options include 0 Input unmonitored 2 Analog Input 3 Digital input monitored 4 Digital output low 5 Digital output high AD3 DI03 Configuration Configure options for the AD3 DIO3 line of the module Options include 0 Input unmonitored 2 Analog Input 3 Digital input monitored 4 Digital output low 5 Digital output high AD4 DI04 Configuration Configure options for the AD4 DIO4 line of the module Options include 0 Input unmonitored 2 Analog Input 3 Digital input monitored 4 Digital output low 5 Digital output high AD5 DIO5 Configuration Configure options for the AD5 DIOS line of the module Options
98. l Module 50 ohm RF connection of pin 36 microstrip trace RPSMA jack PCB Layer 1 of RF Layout Example 2012 Digi International Inc 14 XBee 865 868LP RF Modules Use multiple vias to Puta solid ground plane under RF trace help eliminate to achieve desired impedance ground variations PCB Layer 2 of RF Layout Example Module Operation for Programmable Variant The modules with the programmable option have a secondary processor with 32k of flash and 2k of RAM This allows module integrators to put custom code on the XBee module to fit their own unique needs The DIN DOUT RTS CTS and RESET lines are intercepted by the secondary processor to allow it to be in control of the data transmitted and received All other lines are in parallel and can be controlled by either the internal microcontroller or the MC9SO8QE micro see Block Diagram for details The internal microcontroller by default has control of certain lines These lines can be released by the internal microcontroller by sending the proper command s to disable the desired DIO line s see XBee Command Reference Tables In order for the secondary processor to sample with ADCs the XBee pin 27 VREF must be connected to a reference voltage Digi provides a bootloader that can take care of programming the processor over the air or through the serial interface This means that over the air updates can be supported through an XMODEM protocol The processor can a
99. last packet received was 96dBm MAC ACK Timeouts This count is incremented whenever a MAC ACK timeout occurs on a MAC level unicast Once the number reaches OxFFFF further events will not be counted The counter can be reset to any 16 bit value by appending a hexadecimal parameter to the command 0 OxF FFF 0 OxF FFF 0 OxF FFF Oxff74 to 0x0258 0 OxF FFF UA MAC Unicast Transmission Count This count is incremented whenever a MAC unicast transmission occurs for which an ACK is requested Once the number reaches OxFFFF further events will not be counted The counter can be reset to any 16 bit value by appending a hexadecimal parameter to the command 0 OxFFFF BC RF Byte Count This count is incremented for every PHY level byte transmitted The purpose of this count is to estimate battery life by tracking time doing transmissions This number rolls over to zero from OxFFFF The counter can be reset to any 16 bit value by appending a hexadecimal parameter to the command 0 OxFFFF 2012 Digi International Inc 72 XBee 865 868LP RF Modules AT Command Options AT Command Options Commands AT Command Name and Description Command Mode Timeout Set Read the period of inactivity no valid commands received after which the RF module automatically exits AT Command Mode and returns to Idle Mode Parameter Range 2 0x1770 Default 0x64 100d Guard Times Set required peri
100. le Datasheet and MC9SO8QE32 Minimum Reset Pulse for Programmable 100nS Minimum Reset Pulse to Radio 50nS VREF Range 1 8VDC to VCC 2012 Digi International Inc 8 XBee 865 868LP RF Modules Mechanical Drawings Mechanical drawings of the XBee 865 868LP RF Modules antenna options not shown All dimentions are in inches TOP VIEW SIDE VIEW BOTTOM VIEW PIN 1 OOO or gt lt 0 079 0 055 O ba 1 33 be 0 87 gt 0 12 RENA 0 06 y ig 2012 Digi International Inc XBee 865 868LP RF Modules Pin Signals Pin Assignments for XBee Modules Low asserted signals are distinguished with a horizontal line above signal name Direction Default State Description GND Ground VCC Power Supply DOUT DIO13 Output UART Data Out GPIO DIN CONFIG DIO14 Input UART Data In GPIO DIO12 GPIO RESET Module Reset RSSI PWM DIO10 Output RX Signal Strength Indicator GPIO PWM1 DIO11 Disabled Pulse Width Modulator GPIO reserved Disabled Do Not Connect DTR SLEEP_RQ DIO8 Input Pin Sleep Control Line GPIO GND Ground Serial Peripheral Interface Attention Do not tie low on reset GND Ground SPI_CLK DIO18 Input Serial Peripheral Interface Clock GPIO SPI_SSEL DIO 17 Input Serial Peripheral Interface not Select GPIO SPI_MOSI DIO16 Input Serial Peripheral I
101. lso be programmed and debugged through a one wire interface BKGD Pin 9 2012 Digi International Inc 15 16 1 40 13345 31v3S OL LON INIMYYT ponasos UBL IY oul euopewayu bia z SPa A 1 euopewowu ia ANA S007051 ava INAS GY gt a 21010 TaSS 1dS dvd Asti wzana yeauue 0N oq y9eUu0D oN oq mes 98uU09 30N a am 81010 X7I5714570Yd aoma nyt Ps ZEN fee la ox Paia a WYHS IC 49078 az e a a a a TNS j FTEYWAVHSOUd Nae Sak J me ey Sr J i INS d1 898 598 338X pa aiva STWAOUdd T a f a n F 2 a T r cr 4 a A n n a a a Fe S i T a a BIOIG NLLV 1d5 a d ava uw of a SEND oD NOLASA oa rau AARS S a 5 3 3 5 ae 5 5 E 5 a a 5 O dvd ayd Z5aa2 BRR Va a0ld Ou 47S eLd dvd 2old si3 dve gt gt SeSS EERE a t j ES SS ges te ano ana age 4 B 6OId d1S NO d
102. lso used to store a firmware upgrade file for over the air firmware upgrades of the XBee module itself Accessing General Purpose Flash Memory 2012 Digi International Inc The GPM of a target node can be accessed locally or over the air by sending commands to the MEMORY_ ACCESS cluster ID 0x23 on the DIGI_DATA endpoint OxE6 of the target node using explicit API frames Explicit API frames are described in section XXXX To issue a GPM command the payload of an explicit API frame should be formatted in the following Way Byte Offset in Number of T Payload Bytes Field Name General Field Description 0 1 GPM_CMD_ID Specific GPM commands are described below 1 GPM_OPTIONS Command specific options 2 2 GPM_BLOCK_NUM The block number addressed in the GPM 4 o GPM_START_INDEX The byte index within the addressed GPM block GPM_NUM_BYTES The number of bytes in the GPM_DATA field 6 2 or in the case of a READ the number of bytes requested 7 varies GPM_DATA Multi byte parameters should be specified with big endian byte ordering When a GPM command is sent to a radio via a unicast the receiving radio will unicast a response back to the requesting radio s source endpoint specified in the request packet No response is sent for broadcast requests If the source endpoint is set to the DIGI_DATA endpoint 0xE6 or XBee 865 868LP RF Modules explicit API mode is enabled on the requesting radio then a
103. ly no options defined for the ERASE command Set CPM ORTIONS this field to 0 Set to the index of the GPM block that should be erased When GPM_BLOCK NUM erasing all GPM blocks this field is ignored set to 0 The ERASE command only works on complete GPM blocks The GPM_START_INDEX command cannot be used to erase part of a GPM block For this reason GPM_START_INDEX is unused set to 0 Setting GPM_NUM_BYTES to 0 has a special meaning It indicates that every flash block in the GPM should be erased not just the one GPM_NUM BYTES specified with GPM_BLOCK_NUM In all other cases the GPM_NUM_BYTES field should be set to the GPM flash block size GPM_DATA No data bytes are specified for this command ERASE_RESPONSE 0x81 When an ERASE command request has been unicast to a node that node will send a response in the following format to the source endpoint specified in the requesting frame Field Name Command Specific Description GPM_CMD_ID Should be set to ERASE_RESPONSE 0x81 GPM_STATUS A 1 in the least significant bit indicates an error occurred All other bits are reserved at this time GPM_BLOCK_NUM Matches the parameter passed in the request frame GPM_START_INDEX Matches the parameter passed in the request frame The number of bytes in the GPM_DATA field For this command this GPM_NUM_BYTES field will be set to 0 GPM_DATA No data bytes are specified for this command Exam
104. mand File Since the bootloader flash region is read only the interrupt vector table is redirected to the region OxF1CO to OxF1FD so that application developers can use hardware interrupts Note that in order for Application interrupts to function properly the Application s linker command file prm extension must be modified appropriately to allow the linker to place the developers code in the correct place in memory For example the developer desires to use the serial communications port SCI1 receive interrupt The developer would add the following line to the Codewarrior linker command file for the project VECTOR ADDRESS 0x0000F1E0 vScilRx This will inform the linker that the interrupt function vSci1Rx should be placed at address OxOOOOF1E0 Next the developer should add a file to their project vector_table c that creates an array of function pointers to the ISR routines used by the application extern void _Startup void _ Startup located in Start08 c extern void vScilRx void scil rx isr extern short iWriteToScil unsigned char void vDummylsr void pragma CONST_SEG VECTORS void const vector_table void Relocated Interrupt vector table vDummylsr Int no 0 Vtpm3ovf at F1CO Unassigned vDummylsr Int no 1 Vtpm3ch5 at F1C2 Unassigned vDummylsr Int no 2 Vtpm3ch4 at F1C4 Unassigned vDummylsr Int no 3 Vtpm3ch3 at F1C6 Unassigned vDummylsr Int no 4 Vtpm3ch2 a
105. me ID in the remote command request is set to 0 Network Commissioning and Diagnostics Network commissioning is the process whereby devices in a network are discovered and configured for operation The XBee modules include several features to support device discovery and configuration In addition to configuring devices a strategy must be developed to place devices to ensure reliable routes To accommodate these requirements the XBee modules include various features to aid in device placement configuration and network diagnostics Device Configuration XBee modules can be configured locally through serial commands AT or API or remotely through remote API commands API devices can send configuration commands to set or read the configuration settings of any device in the network ies on 2012 Digi International Inc XBee 865 868LP RF Modules Network Link Establishment and Maintenance Building Aggregate Routes In many applications it is necessary for many or all of the nodes in the network to transmit data to a central aggregator node In anew DigiMesh network the overhead of these nodes discovering routes to the aggregator node can be extensive and taxing on the network To eliminate this overhead the AG command can be used to automatically build routes to an aggregate node in a DigiMesh network To send a unicast modules configured for transparent mode AP 0 must set their DH DL registers to the MAC address
106. modes work the same on SPI as they do on UART However due to the addition of SPI mode there is the option of another sleep pin as described below 2012 Digi International Inc N N XBee 865 868LP RF Modules By default DIO8 SLEEP_REQUEST is configured as a peripheral and is used for pin sleep to awaken and to sleep the radio This applies regardless of the selected serial interface UART or SPI However if SLEEP_REQUEST is not configured as a peripheral and SPI_SSEL is configured as a peripheral then pin sleep is controlled by SPI_SSEL rather than by SLEEP_REQUEST Asserting SPI_SSEL by driving it low either awakens the radio or keeps it awake Negating SPI_SSEL by driving it high puts the radio to sleep Using SPI_SSEL for two purposes to control sleep and to indicate that the SPI master has selected a particular slave device has the advantage of requiring one less physical pin connection to implement pin sleep on SPI It has the disadvantage of putting the radio to sleep whenever the SPI master negates SPI_SSEL meaning time will be lost waiting for the device to wake even if that wasn t the intent Therefore if the user has full control of SPI_SSEL so that it can control pin sleep whether or not data needs to be transmitted then sharing the pin may be a good option in order to make the SLEEP_REQUEST pin available for another purpose If the radio is one of multiple slaves on the SPI then the radio would sleep
107. nd eventually the message will reach all corners of the network Packet tracking prevents a node from resending a broadcast message more than MT 1 times Route Discovery If the source node doesn t have a route to the requested destination the packet is queued to await a route discovery RD process This process is also used when a route fails A route fails when the source node uses up its network retries without ever receiving an ACK This results in the source node initiating RD RD begins by the source node broadcasting a route request RREQ Any router that receives the RREQ that is not the ultimate destination is called an intermediate node Intermediate nodes may either drop or forward a RREQ depending on whether the new RREQ has a better route back to the source node If so information from the RREQ is saved and the RREQ is updated and broadcast When the ultimate destination receives the RREQ it unicasts a route reply RREP back to the source node along the path of the RREQ This is done regardless of route quality and regardless of how many times an RREQ has been seen before This allows the source node to receive multiple route replies The source node selects the route with the best round trip route quality which it will use for the queued packet and for subsequent packets with the same destination address 2012 Digi International Inc 54 XBee 865 868LP RF Moduless Throughput Throughput in a DigiMesh network can
108. ng image shows the API frame exchange that takes place at the UART when sending an AT command request to read or set a module parameter The response can be disabled by setting the frame ID to 0 in the request AT Command Request 0x08 or 0x09 AT Command Response 0x88 I Transmitting and Receiving RF Data The following image shows the API exchanges that take place at the UART when sending RF data to another device The transmit status frame is always sent at the end of a data transmission unless the frame ID is set to 0 in the transmit request If the packet cannot be delivered to the destination the transmit status frame will indicate the cause of failure The received data frame 0x90 or 0x91 is set by the AP command Transmit Request RF Data 0x10 or 0x11 amp ACK Received Data gt Dars gt 0x90 or 0x91 Transmit Status gt 0x88 CEEE Remote AT Commands The following image shows the API frame exchanges that take place at the UART when sending a remote AT command A remote command response frame is not sent out the UART if the remote device does not receive the remote command 2012 Digi International Inc 79 XBee 865 868LP RF Modules Remote AT Command 0x17 Remote AT Command Response 0x97 Supporting the API Applications that support the API should make provisions to deal with new API frames that may be introduced in future releases For example a section of code on a host microprocessor
109. ng to sleep 2012 Digi International Inc 66 6 Command Reference Tables Special Special Commands AT Name and Description Parameter Range Default Command Write Write parameter values to non volatile memory so that parameter modifications WR persist through subsequent resets Note Once WR is issued no additional characters should be sent to the module until after the OK r response is received RE Restore Defaults Restore module parameters to factory defaults CN Exit Command Mode Explicitly exit the module from AT Command Mode FR Software Reset Reset module Responds immediately with an OK then performs a reset 100ms later AC Apply Changes Immediately applies new settings without exiting command mode Addressing Addressing Commands Command Name and Description Destination Address High Set Get the upper 32 bits of the 64 bit destination address When combined with DL it defines the destination address used for transmission Destination Address Low Set Get the lower 32 bits of the 64 bit destination address When combined with DH DL defines the destination address used for transmission Parameter Range 0 to OxFFFFFFFF 0 to OxFFFFFFFF Default Ox0000FFFF Device Type Identifier Stores a device type value This value can be used to differentiate multiple XBee based products 0 0xFFFFFFFF read only 0x40000 Serial Number High Read high 32 bits of the RF
110. nicast to a node that node will send a response in the following format to the source endpoint specified in the requesting frame Example Field Name Command Specific Description GPM_CMD_ID Should be set to READ_RESPONSE 0x84 GPM_STATUS A 1 in the least significant bit indicates an error occurred All other bits are reserved at this time GPM_BLOCK_NUM GPM_START_INDEX Matches the parameter passed in the request frame Matches the parameter passed in the request frame GPM_NUM_BYTES The number of bytes in the GPM_DATA field GPM_DATA The bytes read from the GPM block specified To read 15 bytes of previously written data from flash block 22 of a target radio with serial number of 0x0013a200407402ac a READ packet should be formatted as follows spaces added to delineate fields TE 001C 11 01 0013A200407402AC FFFE E6 E6 0023 C105 00 CO 04 00 0016 0000 000F 3B Assuming all transmissions were successful and that flash block 22 was previously written with incrementing data the following API packets would be output the source node s UART 7E 0007 8B 01 FFFE 00 00 00 76 TE 0029 91 0013A200407402AC FFFE E6 E6 0023 C105 C1 84 00 0016 0000 000F 0102030405060708090AOBOCODOEOF C3 FIRMWARE_VERIFY 0x05 and FIRMWARE_VERIFY_AND_INSTALL 0x06 The FIRMWARE_VERIFY and FIRMWARE_VERIFY_AND_INSTALL commands are used when remotely updating firmware on a module Remote firmware upgrades are covered in detail in s
111. ns were successful and that flash block 22 was previously erased the following API packets would be output the source node s UART TE 0007 8B 01 FFFE 00 00 00 76 TE 001A 91 0013A200407402AC FFFE E6 E6 0023 C105 C1 82 00 0016 0000 0000 4C READ 0x04 2012 Digi International Inc 48 XBee 865 868LP RF Modules 2012 Digi International Inc The READ command can be used to read the specified number of bytes from the GPM location specified Data can be queried from only one GPM block per command Field Name Command Specific Description GPM_CMD_ID Should be set to READ 0x04 GPM_OPTIONS There are currently no options defined for this command Set this field to 0 GPM_BLOCK_NUM Set to the index of the GPM block that should be read GPM_START_INDEX Set to the byte index within the GPM block where the given data should be read GPM_NUM_BYTES Set to the number of data bytes to be read Only one GPM block can be operated on per command For this reason GPM_START_INDEX GPM_NUM_BYTES cannot be greater than the GPM block size It is also important to remember that the number of bytes sent in an explicit API frame including the GPM command fields cannot exceed the maximum payload size of the radio The maximum payload size can be queried with the NP AT command GPM_DATA No data bytes should be specified for this command READ _ RESPONSE 0x84 When a READ command request has been u
112. nse after each frame sent to ensure that the module has had time to process it Serial Transmit Buffer When RF data is received the data is moved into the serial transmit buffer and sent out the UART or SPI port If the serial transmit buffer becomes full and system buffers are also full then the entire RF data packet is dropped Whenever data is received faster than it can be processed and transmitted out the serial port there is a potential of dropping data UART Flow Control The RTS and CTS module pins can be used to provide RTS and or CTS flow control CTS flow control provides an indication to the host to stop sending serial data to the module RTS flow control allows the host to signal the module to not send data in the serial transmit buffer out the UART RTS and CTS flow control are enabled using the D6 and D7 commands Please note that serial port flow control is not possible when using the SPI port CTS Flow Control If CTS flow control is enabled D7 command when the serial receive buffer is 17 bytes away from being full the module de asserts CTS sets it high to signal to the host device to stop sending serial data CTS is re asserted after the serial receive buffer has 34 bytes of space See FT for the buffer size RTS Flow Control If RTS flow control is enabled D6 command data in the serial transmit buffer will not be sent out the DOUT pin as long as RTS is de asserted set high The host device should not de ass
113. nterface Data In GPIO SPI_MISO DIO15 Output Serial Peripheral Interface Data Out GPIO reserved Disabled Do Not Connect reserved Disabled Do Not Connect reserved Disabled Do Not Connect reserved Disabled Do Not Connect GND Ground reserved Disabled Do Not Connect DIO4 Disabled GPIO CTS DIO7 Output Clear to Send Flow Control GPIO ON SLEEP DIO9 Output Module Status Indicator GPIO Not used internally used for programmable secondary processor For compatibility with other XBee modules we recommend connecting this pin to the voltage reference if Analog Sampling is desired Otherwise connect to GND ASSOCIATE DIO5 Output Associate Indicator GPIO RTS DIO6 Input Request to Send Flow Control GPIO AD3 DIO3 Disabled Analog Input GPIO AD2 DIO2 Disabled Analog Input GPIO AD1 DIO1 Disabled Analog Input GPIO ADO DIOO Input Analog Input GPIO reserved Disabled Do Not Connect GND Ground RF RF IO for RF Pad Variant reserved Disabled Do Not Connect Oo ON DD AJ Ww N SPI_ATTN DIO19 Output Output e Signal Direction is specified with respect to the module e See Design Notes section below for details on pin connections e These pins are not available for customer use 2012 Digi International Inc 10 XBee 865 868LP RF Modules
114. o MR 1 times if no acknowledgements are received Supported in the 80k variant only Broadcast Radius Set read the transmission radius for broadcast data transmissions Set to 0 for maximum radius If BH is set greater than NH then the value of NH is used Supported in both variants Name and Description Sleep Mode Set read the sleep mode of the module 0 No sleep mode enabled 1 Pin sleep In this mode the sleep wake state of the module is controlled by the SLEEP_RQ line 4 Asynchronous cyclic sleep In this mode the module periodically sleeps and wakes based on the SP and ST commands 5 Asynchronous cyclic sleep with pin wake up In this mode the module acts in the same way as asynchronous cyclic sleep with the exception that the module will prematurely terminate a sleep period when a falling edge of the SLEEP_RQ line is etected 7 Sleep support mode 8 Synchronous cyclic sleep mode Sleep Options Set read the sleep options of the module This command is a bitmask For synchronous sleep modules the following sleep options are defined bit 0 Preferred sleep coordinator bit 1 Non sleep coordinator Parameter Range 0 1 4 5 7 8 Any of the available sleep option bits can be set or Default SO bit 2 Enable API sleep status messages cleared Bit 0 and bit 1 0x02 bit 3 Disable early wake up cannot be set at the same bit 4 Enable node type equality time bit 5
115. od of silence before and after the Command Sequence Characters of the AT Command Mode Sequence GT CC GT The period of silence is used to prevent inadvertent entrance into AT Command Mode 0 to OxFFFF 0x3E8 10000 Command Character Set or read the character to be used between guard times of the AT Command Mode Sequence The AT Command Mode Sequence causes the radio modem to enter Command Mode from Idle Mode Node Identification Node Identification Commands AT Command FN Name and Description Find Neighbors Discovers and reports all modules found within immediate RF range The following information is reported for each module discovered MY lt CP gt always 0xFFFE SH lt CR gt SL lt CR gt NI lt CR gt Variable length PARENT_NETWORK ADDRESS lt CR gt 2 bytes always OxFFFE DEVICE_TYPE lt CR gt 1 byte 0 Coordinator 1 Router 2 End device See the NO Command STATUS lt CR gt 1 byte reserved PROFILE_ID lt CR gt 2 bytes MANUFACTURER_ID lt CR gt 2 bytes DIGI DEVICE TYPE lt CR gt 4 bytes Optionally included based on NO settings RSSI OF LAST HOP lt CR gt 1 byte Optionally included based on NO settings lt CR gt If the FN command is issued in command mode after NT 100 ms overhead time the command ends by returning a lt CR gt If the FN command is issued via a Local or Remote Command Request API frame each response is returned as a separate Local or Remote AT Command
116. of hops and retries The timeout associated with a unicast assumes the maximum number of hops is necessary as specified by NH The timeout can be estimated in the following manner knownRouteUnicast 2 NH MR unicastOneHopTime 2012 Digi International Inc 56 XBee 865 868LP RF Moduless Transmitting a unicast with an unknown route If the route to the destination is not known the transmitting module will begin by sending a route discovery If the route discovery is successful and a route is found then the data is transmitted The timeout associated with the entire operation can be estimated as follows unknownRouteUnicast BroadcastTxTime NH unicastOneHopTime knownRouteUnicast Transmitting a unicast with a broken route If the route to a destination node has changed since the last time a route discovery was completed a node will begin by attempting to send the data along the previous route After it fails a route discovery will be initiated and upon completion of the route discovery the data will be transmitted along the new route The timeout associated with the entire operation can be estimated as follows brokenRouteUnicast BroadcastTxTime NH unicastOneHopTime 2 knownRouteUnicast 2012 Digi International Inc 57 5 Sleep Mode A number of low power modes exist to enable modules to operate for extended periods of time on battery power These sleep modes are enabled with the SM command The sleep modes are charact
117. ommand is used to tell a node to wake up progressively earlier based on the number of cycles it has gone without receiving a sync This will increase the probability that the un synced node will be awake when the network wakes up and sends the sync message Note using this sleep option increases reliability but may decrease battery life Nodes using this sleep option which miss sync messages will have an increased wake time and decreased sleep time during cycles in which the sync message is missed This will reduce battery conservation 3 When changing between two sets of sleep settings choose settings so that the wake periods of the two sleep settings will happen at the same time In other words try to satisfy the following equation SP1 ST1 N SP2 ST2 where SP1 ST1 and SP2 ST2 are the desired sleep settings and N is an integer Rejoining Nodes Which Have Lost Sync Mesh networks get their robustness from taking advantage of routing redundancies which may be available in a network It is recommended to architect the network with redundant mesh nodes to increase robustness If a scenario exists such that the only route connecting a subnet to the rest of the network depends on a single node and that node fails or the wireless link fails due to changing environmental conditions catastrophic failure condition then multiple subnets may arise while using the same wake and sleep intervals When this occurs the first task is to repair
118. onfiguring and using GPIO ports Electrical Specifications for GPIO Pads GPIO Electrical Specification Value Voltage Supply 2 7 3 6 V Low Schmitt switching threshold 0 3 x Vdd High Schmitt switching threshold 0 7 x Vdd Input pull up resistor value 40 kQ Input pull down resistor value 40 kQ Output voltage for logic 0 0 05 x Vdd Output voltage for logic 1 0 95 x Vdd Output source current 6mA 2012 Digi International Inc 7 XBee 865 868LP RF Modules Electrical Specifications for GPIO Pads GPIO Electrical Specification Output sink current for Total output current for GPIO pads Hardware Specs for Programmable Variant If the module has the programmable secondary processor add the following table values to the specifications listed on page 7 For example if the secondary processor is running at 20 MHz and the primary processor is in receive mode then the new current value will be ltotai Ir2 lrx 14 MA 9 MA 23 MA where I 2 is the runtime current of the secondary processor and I is the receive current of the primary Specifications of the programmable secondary processor These numbers add to specifications Optional Secondary Processor Specification Add to RX TX and sleep currents depending on mode of operation Runtime current for 32k running at 20MHz 14mA Runtime current for 32k running at 1MHz 1mA Sleep current 0 5pA typical For additional aa rit Freesca
119. ors for each digital input can be enabled using the PR command 1 Sample Sets Number of sample sets in the packet Always set to 1 Indicates which digital IO lines have sampling enabled Each bit corresponds to one digital IO line on the module e bit 0 ADO DIOO e bit 1 AD1 DIO1 e bit 2 AD2 DI02 e bit 3 AD3 DIO3 e bit 4 DIO4 e bit 5 ASSOC DIO5 2 Digital Channel Mask e bit 6 RTS DIO6 e bit 7 CTS GPIO7 e bit 8 DTR SLEEP_RQ DIO8 e bit 9 ON_SLEEP DIO9 e bit 10 RSSI DIO10 e bit 11 PWM DIO11 e bit 12 CD DIO12 For example a digital channel mask of 0x002F means DIO0 1 2 3 and 5 are enabled as digital 1O 2012 Digi International Inc 43 XBee 865 868LP RF Modules Indicates which lines have analog inputs enabled for sampling Each bit in the analog channel mask corresponds to one analog input channel e bit 0 ADO DIOO e bit 1 AD1 DIO1 1 Analog Channel Mask e bit 2 AD2 DIO2 e bit 3 AD3 DIO3 e bit 4 AD4 DI04 e bit 5 ASSOC AD5 DIO5 If any digital IO lines are enabled the first two bytes of the data set indicate the state of all enabled digital IO Only digital channels that are enabled in the Digital Channel Mask bytes have any meaning in the sample set If no digital IO are enabled on the Variable Sampled Data Set device these 2 bytes will be omitted Following the digital IO data if any each enabled analog channel will return 2 bytes
120. ote Command Response 92 Appendix H Agency Certifications 93 Appendix Migrating from XBee to SMT Modules 2012 Digi Internaitonal Inc XBee 865 868LP RF Modules 1 RF Module Hardware This manual describes the operation of the XBee XBee 865 868 Low Power SMT RF module which consists of firmware loaded onto XBee S8 hardware XBee and XBee 865 868 Low Power SMT embedded RF modules provide wireless connectivity to end point devices in mesh networks Utilizing the XBee PRO Fea ture Set these modules are interoperable with other devices including devices from other vendors With the XBee users can have their network up and running in a matter of minutes without configuration or additional development The XBee XBee 865 868 modules are not compatible with all XBee products XBee S8 Hardware Description The XBee S8 radio module hardware consists of an Energy Micro EFM32G230F128 microcontroller and Analog Devices ADF7023 radio transceiver and in the programmable version a Freescale MC9S08QE32 microcontroller European Acceptance The XBee 865 868 is manufactured under ISO 900 2000 registered standards XBee 865 868 SMT RF Modules are optimized for use in Europe Please refer to Appendix A for more information 2012 Digi International Inc XBee 865 868LP RF Modules Specifications Specifications of the XBee 865 868LP RF Module Specification Performance up to 370 ft 112 m w 2 1
121. oyed Adding a New Node to an Existing Network To add a new node to the network the node must receive a sync message from a node already in the network On power up an unsynchronized sleep compatible node will periodically send a broadcast requesting a sync message and then sleep for its SP period Any node in the network that receives this message will respond with a sync Because the network can be asleep for extended periods of time and as such cannot respond to requests for sync messages there are methods that can be used to sync a new node while the network is asleep 1 Power the new node on within range of a sleep support node Sleep support nodes are always awake and will be able to respond to sync requests promptly 2 A sleeping cyclic sleep node in the network can be woken by the commissioning button Place the new node in range of the existing cyclic sleep node and wake the existing node by holding down the commissioning button for 2 seconds or until the node wakes The existing node stays awake for 30 seconds and will respond to sync requests while it is awake If you do not use one of these two methods you must wait for the network to wake up before adding the new node The new node should be placed in range of the network with a sleep wake cycle that is shorter than the wake period of the network The new node will periodically send sync requests until the network wakes up and it receives a sync message Changing Sleep Par
122. packets b 11 DigiMesh not available on 10k product 5 Reserved lt set this bit to 0 gt 4 Reserved lt set this bit to 0 gt 3 Trace Route Enable a Trace Route on all DigiMesh API packets 2 NACK Enable a NACK messages on all DigiMesh API packets 1 Disable RD Disable Route Discovery on all DigiMesh unicasts 0 Disable ACK Disable acknowledgments on all unicasts Example 1 Setting TO to 0x80 would cause all transmissions to be sent using repeater mode Example 2 Setting TO to OxC1 would cause all transmissions to be sent using DigiMesh with acknowledgments disabled 2012 Digi International Inc Parameter Range Any 64 bit number Bits 6 amp 7 cannot be set to DigiMesh on the 10k build Bits 4 amp 5 must be set to 0 Bits 1 2 amp 3 cannot be set on the 10k build Default n a 0x40 10k product 0xC0 80k product 68 XBee 865 868LP RF Modules Serial Interfacing 1 O Serial Interfacing Commands AT Name and Description Command API mode Set or read the API mode of the radio The following settings are allowed 0 API mode is off All UART input and output is raw data and packets are delineated using the RO parameter AP 1 API mode is on All UART input and output data is packetized in the API format without escape sequences 2 API mode is on with escaped sequences inserted to allow for control characters XON XOFF escape and the 0x7e delimiter to be passed as
123. pection The pads are all located on the edge of the module so that there are no hidden solder joints on these modules Recommended Solder Reflow Cycle The recommended solder reflow cycle is shown below The chart shows the temperature setting and the time to reach the temperature The cooling cycle is not shown Time seconds Temperature degrees C The maximum temperature should not exceed 260 degrees Celsius The module will reflow during this cycle and therefore must not be reflowed upside down Care should be taken not to jar the module while the solder is molten as parts inside the module can be removed from their required locations Hand soldering is possible and should be done in accordance with approved standards This module has a Moisture Sensitivity Level MSL of 3 2012 Digi International Inc 98 XBee 865 868LP RF Modules Recommended Footprint It is recommended that you use the PCB footprint shown below for surface mounting Dimensions are in inches 0 958 j 1 330 The solder footprint should be matched to the copper pads but may need to be adjusted depending on the specific needs of assembly and product standards While the underside of the module is mostly coated with solder resist it is recommended that the copper layer directly below the module be left open to avoid unintended contacts Copper or vias must not interfere with the three expo
124. ple To erase flash block 42 of a target radio with serial number of 0x0013a200407402ac an ERASE packet should be formatted as follows spaces added to delineate fields 7E 001C 11 01 0013A200407402AC FFFE E6 E6 0023 C105 00 C0 01 00 002A 0000 0200 37 Assuming all transmissions were successful the following API packets would be output the source node s UART TE 0007 8B 01 FFFE 00 00 00 76 7E 001A 91 0013A200407402AC FFFE E6 E6 0023 C105 C1 81 00 002A 0000 0000 39 2012 Digi International Inc 47 XBee 865 868LP RF Modules WRITE 0x02 and ERASE_THEN_WRITE 0x03 The WRITE command writes the specified bytes to the GPM location specified Before writing bytes to a GPM block it is important that the bytes have been erased previously The ERASE_THEN_WRITE command performs an ERASE of the entire GPM block specified with the GPM_BLOCK_NUM field prior to doing a WRITE Field Name Command Specific Description GPM_CMD_ID Should be set to WRITE 0x02 or ERASE_THEN_WRITE 0x03 GPM_OPTIONS ig are currently no options defined for this command Set this field GPM_BLOCK_NUM Set to the index of the GPM block that should be written Set to the byte index within the GPM block where the given data GEM_START_INEEX should be written Set to the number of bytes specified in the GPM_DATA field Only one GPM block can be operated on per command For this reason GPM_START_INDEX GPM_NUM_BYTES cannot be greater than GPM_NU
125. r correct performance With the exception of the RF Pad variant XBees do not require additional ground planes on the host PCB In general antenna elements radiate perpendicular to the direction they point Thus a vertical antenna emits across the horizon Metal objects near the antenna cause reflections and may reduce the ability for an antenna to radiate efficiently Metal objects between the transmitter and receiver can also block the radiation path or reduce the transmission distance so external antennas should be positioned away from them as much as possible Some objects that are often overlooked are metal poles metal studs or beams in structures concrete it is usually reinforced with metal rods metal enclosures vehicles elevators ventilation ducts refrigerators microwave ovens batteries and tall electrolytic capacitors 2012 Digi International Inc 11 XBee 865 868LP RF Modules Design Notes for PCB Antenna Modules PCB Antenna modules should not have any ground planes or metal objects above or below the antenna For best results the module should not be placed in a metal enclosure which may greatly reduce the range The module should be placed at the edge of the PCB on which it is mounted The ground power and signal planes should be vacant immediately below the antenna section The drawing on the following page illustrates important recommendations for designing with the PCB Antenna module It should be noted that
126. r values in the sequence can be modified to reflect user preferences NOTE Failure to enter AT Command Mode is most commonly due to baud rate mismatch By default the BD Baud Rate parameter 3 9600 bps To Send AT Commands Send AT commands and parameters using the syntax shown below Syntax for sending AT Commands AT ASCII Space Parameter Carriage Prefix Command optional optional HEX Return a Example ATDL 1F lt CR gt To read a parameter value stored in the RF module s register omit the parameter field The preceding example would change the RF module Destination Address Low to Ox1F To store the new value to non volatile long term memory send the WR Write command This allows modified parameter values to persist in the module s registry after a reset Otherwise parameters are restored to previously saved values after the module is reset 2012 Digi International Inc Qo Go XBee 865 868LP RF Modules Command Response When a command is sent to the module the module will parse and execute the command Upon successful execution of a command the module returns an OK message If execution of a command results in an error the module returns an ERROR message Applying Command Changes Any changes made to the configuration command registers through AT commands will not take effect until the changes are applied For example sending the BD command to change t
127. ration 22 RF Module Operation 24 Basic Operational Design 24 Listen Before Talk Automatic Frequency Agility LBT AFA g Band Mode 24 g4 Band Mode 25 Serial Communications 25 UART Data Flow 25 SPI Communications 26 SPI Operation 26 Configuration 28 Data Format 28 SPI Parameters 28 Serial Buffers 29 UART Flow Control 29 Serial Interface Protocols 30 Modes of Operation 31 Description of Modes 31 Transmit Mode 31 Receive Mode 33 Command Mode 33 Sleep Mode 34 2012 Digi Internaitonal Inc 3 Advanced Application Features 35 Remote Configuration Commands 35 Sending a Remote Command 35 Applying Changes on Remote Devices 35 Remote Command Responses 35 Network Commissioning and Diagnostics 35 Device Configuration 35 Network Link Establishment and Maintenance 36 Device Placement 37 Device Discovery 37 Link Reliability 38 Commissioning Pushbutton and Associate LED 40 1 O Line Monitoring 42 I O Samples 42 Queried Sampling 42 Periodic I O Sampling 44 Digital O Change Detection 44 General Purpose Flash Memory 45 Accessing General Purpose Flash Memory 45 Over the Air Firmware Upgrades 51 Distributing the New Application 51 Verifying the New Application 52 Installing the Application 52 Things to Remember 52 4 Networking Methods 53 Directed Broadcast Repeater Mode 53 Point to Point Multipoint 53 Permanent dedicated 53 Switched 53 DigiMesh Networking 53 DigiMesh Feature Set 53 Networking Concepts 54 Dev
128. rever the Bootloader increments BLResetCause after each watchdog or illegal instruction reset If this register reaches above 0x10 the bootloader will stop running the application for a few minutes to allow an OTA or Local update to occur If no update is initiated within the time period BLResetCause is cleared and the application is started again To prevent unexpected halting of the application the application shall clear or decrement BLResetCause just before a pending reset To disable this feature the application shall clear BLResetCause at the start of the application 2012 Digi International Inc 17 XBee 865 868LP RF Modules 2012 Digi International Inc Application Flash Data Area Ba e Application 28 160 bytes pplication version string pointer Interupt Vector Table indirection OxF1FE App Start Vector Application Bootloader Shared RAM Data 0x0200 0x0202 0x0204 0x0206 0x020C Ox020E Figure 1 MC9S08QE32 Memory Map 18 XBee 865 868LP RF Modules Operation Upon reset of any kind the execution control begins with the bootloader If the reset cause is Power On reset POR Pin reset PIN or Low Voltage Detect LVD reset LVD the bootloader will not jump to the application code if the override bits are set to RTS D7 1 DTR D5 0 and DIN BO 0 Otherwise the bootloader writes the reset cause NOTHING to the shared data region and jumps to the Application Re
129. rmat to the source endpoint specified in the requesting frame Field Name Command Specific Description GPM_CMD_ID Should be set to PLATFORM_INFO 0x80 GPM_STATUS A 1 in the least significant bit indicates an error occurred All other bits are reserved at this time GPM_BLOCK_NUM Indicates the number of GPM blocks available GPM_START_INDEX Indicates the size in bytes of a GPM block GPM_NUM_BYTES The number of bytes in the GPM_DATA field For this command this field will be set to 0 GPM_DATA No data bytes are specified for this command Example A PLATFORM_INFO_REQUEST sent to a radio with a serial number of 0x0013a200407402AC should be formatted as follows spaces added to delineate fields 2012 Digi International Inc 46 XBee 865 868LP RF Modules TE 001C 11 01 0013A200407402AC FFFE E6 E6 0023 C105 00 00 00 00 0000 0000 0000 24 Assuming all transmissions were successful the following API packets would be output the source node s UART TE 0007 8B 01 FFFE 00 00 00 76 TE 001A 91 0013A200407402AC FFFE E6 E6 0023 C105 C1 80 00 0077 0200 0000 EB ERASE 0x01 The ERASE command erases writes all bits to binary 1 one or all of the GPM flash blocks The ERASE command can also be used to erase all blocks of the GPM by setting the GPM_NUM_BYTES field to 0 Field Name Command Specific Description GPM_CMD_ID Should be set to ERASE 0x01 There are current
130. s cited below gt Transmitting data to multiple destinations without entering Command Mode gt Receive success failure status of each transmitted RF packet gt Identify the source address of each received packet A Comparison of Transparent and API Operation The following table compares the advantages of transparent and API modes of operation Transparent Operation Features Simple Interface All received serial data is transmitted unless the module is in command mode Easy to support It is easier for an application to support transparent operation and command mode API Operation Features Transmitting RF data to multiple remotes only requires changing the address in the API frame This Easy to manage data process is much faster than in transparent operation where the application must enter AT command transmissions to multiple mode change the address exit command mode and then transmit data destinations Each API transmission can return a transmit status frame indicating the success or reason for failure Received data frames indicate the sender s All received RF data API frames indicate the source address address Advanced addressing API transmit and receive frames can expose addressing fields including source and destination support endpoints cluster ID and profile ID 2012 Digi International Inc 30 XBee 865 868LP RF Modules Transparent Operation Features Advanced networking
131. s of 0x0013A20001238400 using a source endpoint of 0xA0 destination endpoint OxA1 cluster ID 0x1554 and profile ID 0xC105 Payload will be TxData 2012 Digi International Inc 83 XBee 865 868LP RF Modules Remote AT Command Request Frame Type 0x17 Used to query or set module parameters on a remote device For parameter changes on the remote device to take effect changes must be applied either by setting the apply changes options bit or by sending an AC command to the remote Start Delimiter 0x00 0x10 Number of bytes between the length and the checksum 0x17 Identifies the UART data frame for the host to correlate 0x01 with a subsequent ACK acknowledgement If set to 0 no response is sent 0x00 0x13 OxA2 Set to the 64 bit address of the destination device The 0x00 following address is also supported 0x40 0x000000000000FFFF Broadcast address 0x40 0x11 0x22 Frame specific Data OxFF OxFE Set to OxFFFE 0x02 Apply changes on remote If not set AC command must be sent before changes will take effect All other bits must be set to 0 0x02 apply changes Name of the command If present indicates the requested parameter value to set the given register If no characters present the register is queried Checksum OxFF the 8 bit sum of bytes from offset 3 to this byte Example The above example sends a remo
132. s that might be mounted in keepout area 4 These keepout area guidelines do not apply for Wire Whip antennas or external RF connectors Wire Whip antennas radiate best over the center of a ground plane 4 K REV ECO DESCRIPTION OF CHANGE BY CKD APPR DATE TITLE APPROVALS DATE XBee XBee PRO SMT DESIGNED PCB Antenna DRAWN Keepout Area CHECKED ENGINEER PART NO REV Digi International Inc 2 3 4 All rights reserved DO NOT SCALE DRAWING SHEET 1 of 1 2012 Digi International Inc 13 XBee 865 868LP RF Modules Design Notes for RF Pad Modules The RF Pad is a soldered antenna connection The RF signal travels from pin 36 on the module to the antenna through an RF trace transmission line on the PCB Please note that any additional components between the module and antenna will violate modular certification The RF trace should have a controlled impedance of 50 ohms We recommend using a microstrip trace although coplanar waveguide may also be used if more isolation is needed Microstrip generally requires less area on the PCB than coplanar waveguide Stripline is not recommended because sending the signal to different PCB layers can introduce matching and performance problems It is essential to follow good design practices when implementing the RF trace on a PCB The following figures show a layout example of a host PCB that connects an RF Pad module to a right angle through hole RPSMA jack The top two la
133. sed RF test points on the bottom of the module see below Furthermore these modules have a ground plane in the middle on the back side for shielding purposes which can be affected by copper traces directly below the module E 5 0 315 COPPER KEEP OUT 2012 Digi International Inc 99 XBee 865 868LP RF Modules Flux and Cleaning It is recommended that a no clean solder paste be used in assembling these modules This will eliminate the clean step and ensure unwanted residual flux is not left under the module where it is difficult to remove In addition e Cleaning with liquids can result in liquid remaining under the shield or in the gap between the module and the OEM PCB This can lead to unintended connections between pads on the mod ule e The residual moisture and flux residue under the module are not easily seen during an inspec tion process Factory recommended best practice is to use a no clean solder paste to avoid the issues above and ensure proper module operation Reworking Rework should never be performed on the module itself The module has been optimized to give the best possible performance and reworking the module itself will void warranty coverage and certifications We recognize that some customers will choose to rework and void the warranty the following information is given as a guideline in such cases to increase the chances of
134. set causes are defined in the file common h in an enumeration with the following definitions typedef enum BL_CAUSE_NOTHING 0x0000 PIN LVD POR BL_CAUSE_NOTHING_COUNT 0x0001 BL_Reset_Cause counter Bootloader increments cause every reset BL_CAUSE_BAD_APP 0x0010 Bootloader considers APP invalid BL_RESET_CAUSES typedef enum APP_CAUSE_NOTHING 0x0000 APP_CAUSE_USE001 0x0001 0x0000 to Ox00FF are considered valid for APP use APP_CAUSE_USE255 OxO00FF APP_CAUSE_FIRMWARE_UPDATE 0x5981 APP_CAUSE_BYPASS_MODE 0x4682 APP_CAUSE_BOOTLOADER_MENU 0x6A18 APP_RESET_CAUSES Otherwise if the reset cause is a watchdog or other reset the bootloader checks the shared memory region for the APP_RESET_CAUSE If the reset cause is 1 APP_CAUSE_NOTHING or 0x0000 to OxOOFF the bootloader increments the BL_RESET_CAUSES verifies that it is still less than BL_CAUSE_BAD_APP and jumps back to the application If the Application does not clear the BL_RESET_CAUSE it can prevent an infinite loop of running a bad application that continues to perform illegal instructions or watchdog resets 2 APP_CAUSE_FIRMWARE_UPDATE the bootloader has been instructed to update the application over the air from a specific 64 bit address In this case the bootloader will attempt to initiate an Xmodem transfer from the 64 bit address located in shared RAM 3 APP_CAUSE_BYPASS_MODE the bootloader executes bypass mode
135. sh button is pressed once the device transmits a broadcast node identification packet at the beginning of the next wake cycle if sleep compatible or immediately if not sleep compatible If the Associate LED functionality is enabled D5 command a device that receive this transmission will blink its Associate pin rapidly for 1 second 1 O Line Monitoring 1 O Samples The XBee modules support both analog input and digital 10 line modes on several configurable pins Queried Sampling Parameters for the pin configuration commands typically include the following Pin Command Parameter Description Unmonitored digital input Reserved for pin specific alternate functionalities 2012 Digi International Inc 42 XBee 865 868LP RF Modules Pin Command Parameter Description Analog input A D pins or PWM output PWM pins Digital input monitored Digital output low Digital output high Alternate functionalities where applicable Setting the configuration command that corresponds to a particular pin will configure the pin Module Pin Names Module Pin Number Configuration Command CD DIO12 po PWMO RSSI DIO10 PWM1 DIO11 DTR SLEEP_RQ DIO8 AD4 DIO4 CTS DIO7 ON_SLEEP DIO9 ASSOC AD5 DIO5 RTS DIO6 AD3 DIO3 AD2 DIO2 AD1 DIO1 ADO DIOO CommissioningButton See the command table for more information Pullup resist
136. should be ignored Parameter Range Default Operational Sleep Period ead the sleep period that the node is currently using This number will oftentimes be ifferent from the SP parameter if the node has synchronized with a sleeping router network Units of 10mSec Operational Wake Period Read the wake time that the node is currently using This number will oftentimes be different from the ST parameter if the node has synchronized with a sleeping router network Units of 1 ms Wake Host Set Read the wake host timer value If the wake host timer is set to a non zero value this timer specifies a time in millisecond units that the device should allow after waking from sleep before sending data out the UART or transmitting an I O sample If serial characters are received the WH timer is stopped immediately When in synchronous sleep the device will shorten its sleep period by the value specified by the WH command to ensure that it is prepared to communicate when the network wakes up When in this this sleep mode the device will always stay awake for the WH time plus the amount of time it takes to transmit a one hop unicast to another node 2012 Digi International Inc 0 OxFFFF x 1ms 7 API Operation As an alternative to Transparent Operation API Application Programming Interface Operations are available API operation requires that communication with the module be done through a
137. sleep support node can be removed If desired the sleep cycle settings can be changed back to what they were In the case that only a few nodes need to be replaced this method can also be used 1 Reset the out of sync node and set its sleep mode to cyclic sleep SM 8 Set it up to havea short sleep cycle 2012 Digi International Inc 65 XBee 865 868LP RF Modules 2 Place the node in range of a sleep support node or wake a sleeping node with the commissioning button 3 The out of sync node will receive a sync from the node which is synchronized to the network and sync to the network sleep settings Diagnostics The following are useful in some applications when managing a sleeping router network Query current sleep cycle the OS and OW command can be used to query the current operational sleep and wake times a module is currently using Sleep Status the SS command can be used to query useful information regarding the sleep status of the module This command can be used to query if the node is currently acting as a network sleep coordinator as well as other useful diagnostics Missed Sync Messages Command the MS command can be used to query the number of cycles that have elapsed since the module last received a sync message Sleep Status API messages when enabled with the SO command a module configured in API mode will output modem status frames immediately after a module wakes up and just prior to a module goi
138. structured interface data is communicated in frames in a defined order The API specifies how commands command responses and module status messages are sent and received from the module using a UART Data Frame Please note that Digi may add new frame types to future versions of firmware so please build into your software interface the ability to filter out additional API frames with unknown Frame Types API Frame Specifications Two API modes are supported and both can be enabled using the AP API Enable command Use the following AP parameter values to configure the module to operate in a particular mode e AP 1 API Operation e AP 2 API Operation with escaped characters API Operation AP parameter 1 When this API mode is enabled AP 1 the UART data frame structure is defined as follows Figure 7 01 UART Data Frame Structure Start Delimiter Length Frame Data Checksum Byte 1 Bytes 2 3 Bytes 4 n Byte n 1 0x7E MSB LSB API specific Structure 1 Byte MSB Most Significant Byte LSB Least Significant Byte Any data received prior to the start delimiter is silently discarded If the frame is not received correctly or if the checksum fails the module will reply with a module status frame indicating the nature of the failure API Operation with Escape Characters AP parameter 2 When this API mode is enabled AP 2 the UART data frame structure is defined as follows Figure 7 02
139. success during rework though the warranty is still voided The module may be removed from the OEM PCB by the use of a hot air rework station or hot plate Care should be taken not to overheat the module During rework the module temperature may rise above its internal solder melting point and care should be taken not to dislodge internal components from their intended positions 2012 Digi International Inc 100 Mouser Electronics Authorized Distributor Click to View Pricing Inventory Delivery amp Lifecycle Information Digi International XK8 DMSBO
140. t unconnected inputs should never be left floating Use internal or external pull up or pull down resistors or set the unused 1 0 lines to outputs Other pins may be connected to external circuitry for convenience of operation including the Associate LED pad pad 28 and the Commissioning pad pad 33 The Associate LED pad will flash differently depending on the state of the module to the network and a pushbutton attached to pad 33 can enable various join functions without having to send serial port commands Please see the commissioning pushbutton and associate LED section in chapter 7 for more details The source and sink capabilities are limited to 6mA on all I O pads The VRef pad pad 27 is only used on the programmable versions of these modules For compatibility with other XBee modules we recommend connecting this pin to a voltage reference if analog sampling is desired Otherwise connect to GND Board Layout XBee modules are designed to be self sufficient and have minimal sensitivity to nearby processors crystals or other PCB components As with all PCB designs Power and Ground traces should be thicker than signal traces and able to comfortably support the maximum current specifications A recommended PCB footprint for the module can be found in Appendix C No other special PCB design considerations are required for integrating XBee radios except in the antenna section The choice of antenna and antenna location is very important fo
141. t F1C8 Unassigned vDummylsr Int no 5 Vtpm3ch1 at FICA Unassigned vDummylsr Int no 6 Vtpm3chO at FICC Unassigned vDummylsr Int no 7 Vrtc at F1CE Unassigned vDummylsr Int no 8 Vsci2tx at F1DO Unassigned vDummylsr Int no 9 Vsci2rx at F1D2 Unassigned vDummylsr Int no 10 Vsci2err at F1D4 Unassigned vDummylsr Int no 11 Vacmpx at F1D6 Unassigned vDummylsr Int no 12 Vadc at F1D8 Unassigned vDummylsr Int no 13 Vkeyboard at FIDA Unassigned vDummylsr Int no 14 Viic at FIDC Unassigned vDummylsr Int no 15 Vsciltx at FIDE Unassigned vScilRx Int no 16 Vscilrx at F1E0 SCI1RX vDummylsr Int no 17 Vscilerr at F1E2 Unassigned vDummylsr Int no 18 Vspi at F1E4 Unassigned vDummylsr Int no 19 VReserved12 at F1E6 Unassigned vDummylsr Int no 20 Vtpm2ovf at F1E8 Unassigned vDummylsr Int no 21 Vtpm2ch2 at F1EA Unassigned vDummylsr Int no 22 Vtpm2ch1 at FIEC Unassigned vDummylsr Int no 23 Vtpm2chO at F1EE Unassigned vDummylsr Int no 24 Vtpmiovf at FIFO Unassigned vDummylsr Int no 25 Vtpmich2 at F1F2 Unassigned vDummylsr Int no 26 Vtpmich1 at F1F4 Unassigned vDummylsr Int no 27 VtpmichO at F1F6 Unassigned 2012 Digi International Inc 20 XBee 865 868LP RF Modules vDummylsr Int no 28 Vivd at F1F8 Unassigned vDummylsr In
142. t no 29 Virq at F1FA Unassigned vDummylsr Int no 30 Vswi at F1FC Unassigned _Startup Int no 31 Vreset at F1FE Reset vector F void vDummylsr void for if iWriteToSci1 STUCK IN UNASSIGNED ISR n r gt The interrupt routines themselves can be defined in separate files The vDummylsr function is used in conjunction with iWritetoScil1 for debugging purposes Bootloader Menu Commands The bootloader accepts commands from both the local UART and OTA All OTA commands sent must be Unicast with only 1 byte in the payload for each command A response will be returned to the sender All Broadcast and multiple byte OTA packets are dropped to help prevent general OTA traffic from being interpreted as a command to the bootloader while in the menu Bypass Mode B The bootloader provides a bypass mode of operation that essentially connects the freescale mcu to the internal microcontroller s serial UART This allows direct communication to the internal microcontroller s radio for the purpose of firmware and radio configuration changes Once in bypass mode the X CTU utility can change modem configuration and or update module s firmware Bypass mode automatically handles any baud rate up to 115 2kbps Note that this command is unavailable when module is accessed remotely Update Firmware F The F command initiates a firmware download for both wired and over the air configurations Depen
143. te command to change the broadcast hops register on a remote device to 1 broadcasts go to 1 hop neighbors only and apply changes so the new configuration value immediately takes effect In this example the 64 bit address of the remote is 0x0013A200 40401122 2012 Digi International Inc 84 XBee 865 868LP RF Modules AT Command Response Frame Type 0x88 In response to an AT Command message the module will send an AT Command Response message Some commands will send back multiple frames for example the ND Node Discover command Start Delimiter Frame specific Data Checksum Ox7E 0x00 0x05 Number of bytes between the length and the checksum 0x88 0x01 Identifies the UART data frame being reported Note If Frame ID 0 in AT Command Mode no AT Command Response will be given B 0x42 D 0x44 Command Name Two ASCII characters that identify the AT Command The least significan nibble indicates the command status 0 OK 1 ERROR 2 Invalid Command 3 Invalid Parameter The most significant nibble is a bitfield as follows 0x40 The RSSI field is invalid and should be ignored Software prior to version 8x60 did not include RSSI information 0x80 Response is a remote command Register data in binary format If the register was set then this field is not returned as in this example OxFF the 8 bit sum of bytes from offset
144. the available transmission time Auto Early Wake Up Sleep Option Similarly to the sleep guard time the auto early wake up option decreases the sleep period based on the number of sync messages missed This option comes at the expense of battery life Auto early wake up sleep can be disabled using the sleep options SO command Configuration Selecting Sleep Parameters Choosing proper sleep parameters is vital to creating a robust sleep enabled network with a desireable battery life To select sleep parameters that will be good for most applications follow these steps 1 Choose NH Based on the placement of the nodes in your network select appropriate values for the Network Hops NH parameter Note the default value of NH has been optimized to work for the majority of deployments In most cases we suggest that the parameter not be modified from its default value Decreasing its parameters for small networks can improve battery life but care should be taken so that the value is not made too small 2 Calculate the Sync Message Propagation Time SMPT This is the maximum amount of time it takes for a sleep synchronization message to propagate to every node in the network This number can be estimated with the following formula SMPT NH MT 1 18ms 3 Select desired duty cycle The ratio of sleep time to wake time is the factor that has the greatest effect on the RF module s power consumption Battery life can be es
145. this RI packet out its UART upon reception It is important to note that Route Information packets are not guaranteed to arrive in the same order as the unicast packet took It is also possible for the transmission of Route Information packets on a weak route to fail before arriving at the unicast originator Because of the large number of Route Information packets which can be generated by a unicast with Trace Route enabled it is suggested that the Trace Route option only be used for occasional diagnostic purposes and not for normal operations NACK Messages The NACK API option of Tx Request Packets see the API section of this manual for a description of the API frames provides the option to have a Route Information packet generated and sent to the originator of a unicast when a MAC acknowledgment failure occurs on one of the hops to the destination This information is useful because it allows marginal links to be identified and repaired Commissioning Pushbutton and Associate LED 2012 Digi International Inc The XBee modules support a set of commissioning and LED behaviors to aid in device deployment and commissioning These include the commissioning push button definitions and associate LED behaviors These features can be supported in hardware as shown below Commissioning Pushbutton and Associate LED Functionalities 40 XBee 865 868LP RF Modules A pushbutton Push button 20 O eo XB
146. timated based on the following factors sleep period wake time sleep current RX current TX current and battery capacity 4 Choose sleep period and wake time The wake time needs to be long enough to transmit the desired data as well as the sync message The ST parameter will automatically adjust upwards to its minimum value when other AT commands are changed that will affect it SP and NH Use a value larger than this minimum If a module misses successive sync messages it reduces its available transmit time to compensate for possible clock drift Budget a large enough ST time to allow for a few sync messages to be missed and still have time for normal data transmissions Starting a Sleeping Network By default all new nodes operate in normal non sleep mode To start a sleeping network follow these steps 2012 Digi International Inc 63 XBee 865 868LP RF Modules 1 Enable the preferred sleep coordinator option on one of the nodes and set its SM to a sleep compatible mode 7 or 8 with its SP and ST set to a quick cycle time The purpose of a quick cycle time is to allow commands to be sent quickly through the network during commissioning 2 Next power on the new nodes within range of the sleep coordinator The nodes will quickly receive a sync message and synchronize themselves to the short cycle SP and ST 3 Configure the new nodes in their desired sleep mode as cyclic sleeping nodes or sleep support nodes
147. tization the RF module will attempt to transmit the data The destination address determines which node s will receive and send the data In the diagram below route discovery applies only to DigiMesh transmissions The data will be transmitted once a route is established If route discovery fails to establish a route the packet will be discarded 2012 Digi International Inc XBee 865 868LP RF Mod ules Transmit Mode Sequence Successful Transmission Idle Mode New Transmission 2012 Digi International Inc Data Discarded Route Known Transmit Data Route Discovery Route Discovered 32 XBee 865 868LP RF Modules When data is transmitted from one node to another a network level acknowledgement is transmitted back across the established route to the source node This acknowledgement packet indicates to the source node that the data packet was received by the destination node If a network acknowledgement is not received the source node will re transmit the data It is possible in rare circumstances for the destination to receive a data packet but for the source to not receive the network acknowledgment In this case the source will retransmit the data which could cause the destination to receive the same data packet multiple times The XBee modules do not filter out duplicate packets The application should include provisions to address this potential issue
148. uld be mains powered A normal mode module will synchronize to a sleeping network but will not observe synchronization data routing rules it will route data at any time regardless of the wake state of the network When synchronized a normal node will relay sync messages generated by sleep compatible nodes but will not generate sync messages Once a normal node has synchronized with a sleeping network it can be put into a sleep compatible sleep mode at any time Asynchronous Pin Sleep Mode SM 1 Pin sleep allows the module to sleep and wake according to the state of the Sleep_ RQ pin pin 9 Pin sleep mode is enabled by setting the SM command to 1 When Sleep_ RQ is asserted high the module will finish any transmit or receive operations and enter a low power state The module will wake from pin sleep when the Sleep_ RQ pin is de asserted low Asynchronous Cyclic Sleep Mode SM 4 Cyclic sleep allows the module to sleep for a specified time and wake for a short time to poll Cyclic sleep mode is enabled by setting the SM command to 4 In cyclic sleep the module sleeps for a specified time If the XBee receives serial or RF data while awake it will then extend the time before it returns to sleep by the amount specified by the ST command Otherwise it will enter sleep mode immediately The On_ SLEEP line is asserted high when the module wakes and is de asserted low when the module sleeps If hardware flow control is enabled D7
149. uld be used with caution The advantages of using the option become weaknesses when used on a node that is not positioned or configured properly The preferred sleep coordinator option can also be used when setting up a network for the first time When starting a network a node can be configured as a sleep coordinator so it will begin sending sleep messages After the network is set up the preferred sleep coordinator bit can be disabled Nomination and Election Nomination is an optional process that can occur on a node in the event that contact with the network sleep coordinator is lost By default this behavior is disabled This behavior can be enabled with the sleep options command SO This process will automatically occur in the event that contact with the previous sleep coordinator is lost Any sleep compatible node which has this behavior enabled is eligible to become the sleep coordinator for the network If a sleep compatible node has missed three or more sync messages and is not configured as a non sleep coordinator presumably because the sleep coordinator has been disabled it may become a sleep coordinator Depending on the platform and other configured options such a node will eventually nominate itself after a number of cycles without a sync A nominated node will begin acting as the new network sleep coordinator It is possible for multiple nodes to nominate themselves as the sleep coordinator If this occurs an election will take plac
150. ules XBee Programmable Bootloader Overview The XBee Programmable module is equipped with a Freescale MC9SO8QE32 application processor This application processor comes with a supplied bootloader This section describes how to interface the customer s application code running on this processor to the XBee Programmable module s supplied bootloader The first section discusses how to initiate firmware updates using the supplied bootloader for wired and over the air updates Bootloader Software Specifics Memory Layout Figure 1 shows the memory map for the MC9SO8QE32 application processor The supplied bootloader occupies the bottom pages of the flash from OxF200 to OxFFFF Application code cannot write to this space The application code can exist in Flash from address 0x8400 to OxF1BC 1k of Flash from 0x8000 to Ox83FF is reserved for Non Volatile Application Data that will not be erased by the bootloader during a flash update A portion of RAM is accessible by both the application and the bootloader Specifically there is a shared data region used by both the application and the bootloader that is located at RAM address 0x200 to 0x215 Application code should not write anything to BLResetCause or AppResetCause unless informing the bootloader of the impending reset reason The Application code should not clear BLResetCause unless it is handling the unexpected reset reason To prevent a malfunctioning application from running fo
151. uppose that the link between radio A SH SL 0x0013a20040521234 and radio B SH SL 0x0013a2004052abcd is to be tested by transmitting 1000 40 byte packets The following API packet should be sent to the UART of the radio on which the results should be output radio C Note that radio C can be the same radio as radio A or B whitespace used to delineate fields bold text is the payload portion of the packet 7E 0020 11 01 0013A20040521234 FFFE E6 E6 0014 C105 00 00 0013A2004052ABCD 0028 03E8 EB And the following is a possible packet that could be returned 7E 0027 91 0013A20040521234 FFFE E6 E6 0094 C105 00 0013A2004052ABCD 0028 03E8 03E7 0064 00 OA 50 53 52 9F 999 out of 1000 packets successful 100 retries used RR 10 maxRSS I 80dBm minRSSI 83dBm avgRSSI 82dBm If the result field is not equal to zero then an error has occurred The other fields in the packet should be ignored If the Success field is equal to zero then the RSSI fields should be ignored Qo Ko XBee 865 868LP RF Modu les Tr ace Routing In many applications it is useful to determine the route which a DigiMesh unicast takes to its destination This information is especially useful when setting up a network or diagnosing problems within a network The Trace Route API option of Tx Request Packets see the API section of this manual for a description of the API frames causes routing information packets to be transmitted to the originator o
152. ust have analog or digital I O functionality enabled see DO D9 PO P2 commands The sample rate is measured in milliseconds 2012 Digi International Inc 0 Ox1FFF 0 0x03FF 0 0x03FF 0x14 OxFF x10ms n a 0 0xFFFF 0 OxFFFF ms Ox1 FFF n a 71 XBee 865 868LP RF Modules I O Commands AT Name and Description Parameter Range Default Command Sleep Sample Rate Set read the number of sleep cycles that must elapse between periodic I O samples 4 IF A 1 0xFF 1 This allows I O samples to be taken only during some wake cycles During those cycles I O samples are taken at the rate specified by IR Commissioning Pushbutton This command can be used to simulate commissioning button presses in software The CB parameter value should be set to the number of button presses to be simulated For 0 4 n a example sending the ATCB1 command will execute the action associated with 1 commissioning button press Diagnostics Diagnostics Commands AT Name and Description Parameter Range Default Command VR Firmware Version Read firmware version of the module T read Firmware set VL Version Long Shows detailed version information including application build date and time HV Hardware Version Read hardware version of the module 0 OxFFFF read only Factory set Configuration Code Read the configuration code associated with the current AT CK command configuration The code returned c
153. ut on SPI In the default configuration the UART and the SPI ports will both be configured for 1 O Initially all serial data will go out the UART But as soon as input occurs on either port that port is selected as the active port and no input or output will be allowed on the other port until the next reset of the module If the configuration is changed so that only one port is configured then that port will be the only one enabled or used If the parameters are written with only one port enabled then the port that is not enabled will not even be used temporarily after the next reset If both ports are disabled on reset the UART will be used in spite of the wrong configuration so that at least one serial port will be operational Serial Receive Buffer When serial data enters the RF module through the DIN Pin or the MOSI pin the data is stored in the serial receive buffer until it can be processed Under certain conditions the module may not be able to process data in the serial receive buffer immediately If large amounts of serial data are sent to the module such that the serial receive buffer would overflow then the new data will be discarded If the UART is in use this can be avoided by the host side honoring CTS flow control If the SPI is the serial port no hardware flow control is available It is the user s responsibility to ensure that receive buffer is not overflowed One reliable strategy is to wait for a TX_STATUS respo
154. v d t 92 J ee onan SOLNE lt 6 _ gt asxe avd Kicsi vora ans SLA B SGIN y UO 9 Utd HIZUA 0 R 2010 5142 zoiazsaa sora uaa F x y s0la a 18 Ne orays oneaa by ola IM e s auuo3 434A aun Jy aidues o F Kooy 01 PPL GOI GSS IS NO age Ae A bal F orasima aya BOSEIN 104 a9u aja Jeue xa Ae ayd E Besa rer soa Aosey saa esu ra Py 0 pa auuos aq ysnw JJYA ee s 301a 544 sorazsss sasas Lo orpey 1as2 7 couareay Zia a IOld BAMA ISSE Ve Ke eaareov noaamosra tS orpeurwia so1d a0ss dvd lt gt _ oraziav soana o1pey Ray 4 il beads See ee 10 PEHTLNOT aol vanmayIsse ofed sdia aossy aug Suuorssiuuoy 0020m he J z ver oaas ans aa GH axe J fon gold SLu dva lt EZ ad G co 9 H asaya n SE y apes 10 z 43534 N Ai peus La ssnosyuozosgu lt anaon ins azex PTAA STH R sziaaezozensa oam 64033 N eold edv dvd sped jeusayxe ZE s gt o pa ssuuos you sue saun saqi open ao z0 J ZNMAGI ZOITOV opes jeuaszur soy ae S19 PUP Si 13S3Y NIG INOG Sreayues BASEN ZOld Zav dvd Nid dvd UY zoid7zav wid ig HoeGnL ale Hr PeT moesie e gt sold SLe PN lold iav ave Sat cHocani eats fo te inoq ave pHa toe gt o1 pey 1 asa ino ees ezanov sHenaissaie Ha gt SSH szanavszaxuzsara Hao pey LNO SONP zanavzzarizeia He PEL NIT 4 old WNOI eav dvd J e A H Oe aul Buluorssiuwoy aora7wnor eay S1011 3735 5 gt H mosaszanenss vosa vaavziarusvanaxzania _
155. value and the command and parameter data optional If a command response is desired the Frame ID should be set to a non zero value Only unicasts of remote commands are supported Remote commands cannot be broadcast Applying Changes on Remote Devices When remote commands are used to change command parameter settings on a remote device parameter changes do not take effect until the changes are applied For example changing the BD parameter will not change the actual serial interface rate on the remote until the changes are applied Changes can be applied using remote commands in one of three ways e Set the apply changes option bit in the API frame e Issue an AC command to the remote device e Issue a WR FR command to the remote device to save changes and reset the device Remote Command Responses If the remote device receives a remote command request transmission and the API frame ID is non zero the remote will send a remote command response transmission back to the device that sent the remote command When a remote command response transmission is received a device sends a remote command response API frame out its UART The remote command response indicates the status of the command success or reason for failure and in the case of a command query it will include the register value The device that sends a remote command will not receive a remote command response frame if e The destination device could not be reached e The fra
156. were successful and that the firmware image previously loaded into the GPM is valid the following API packets would be output the source node s UART 7E 0007 8B 01 FFFE 00 00 00 76 7E 001A 91 0013A200407402AC FFFE E6 E6 0023 C105 C1 85 00 0000 0000 0000 5F Working with Flash Memory When working with the General Purpose Memory the user should be aware of a number of limitations associated with working with flash memory e Flash memory write operations are only capable of changing binary 1 s to binary O s Only the erase operation can change binary 0 s to binary 1 s For this reason it is usually necessary to erase a flash block before performing a write operation e A flash memory block must be erased in its entirety when performing an erase operation A block cannot be partially erased e Flash memory has a limited lifetime The flash memory on which the GPM is based is rated at 20 000 erase cycles before failure Care must be taken to ensure that the frequency of erase write operations allows for the desired product lifetime Digi s warranty will not cover products whose number of erase cycles has been exceeded e Over the Air firmware upgrades described in the next section require the entire GPM be erased Any user data stored in the GPM will be lost during an over the air upgrade Over the Air Firmware Upgrades XBee DigiMesh 868 modules provide two methods of updating the firmware on the module Firmware can be updated locally via
157. yers of the PCB have a controlled thickness dielectric material in between The second layer has a ground plane which runs underneath the entire RF Pad area This ground plane is a distance d the thickness of the dielectric below the top layer The top layer has an RF trace running from pin 36 of the module to the RF pin of the RPSMA connector The RF trace s width determines the impedance of the transmission line with relation to the ground plane Many online tools can estimate this value although the PCB manufacturer should be consulted for the exact width Assuming d 0 025 and that the dielectric has a relative permittivity of 4 4 the width in this example will be approximately 0 045 for a 50 ohm trace This trace width is a good fit with the module footprint s 0 060 pad width Using a trace wider than the pad width is not recommended and using a very narrow trace under 0 010 can cause unwanted RF loss The length of the trace is minimized by placing the RPSMA jack close to the module All of the grounds on the jack and the module are connected to the ground planes directly or through closely placed vias Any ground fill on the top layer should be spaced at least twice the distance d in this case at least 0 050 from the microstrip to minimize their interaction Implementing these design suggestions will help ensure that the RF Pad module performs to its specifications Maintaina distance of at least 2d between microstrip and ground fil

Datasheet - Mouser Electronics

Contents

Download Pdf Manuals

Related Search

Related Contents