Manual - USCutter Support
Contents
1. Making a Simple cut in SignBlazer section of this manual starting on page 27 to make your cut Se 7 Starting SignCut and Inkscape for the First Time Open the SignCut software The Default location will be in the Programs Folder under SignCut Productivity Pro Navigate to this folder and select SignCut fam SignCut Productivity Pro y Check for updates Welcome to SignCut Please walk through this wizard to make the initial setup Click Next to continue Follow the onscreen instructions entering your License number that you received when you registered and downloaded SignCut In order to use SignCut you need to activate your license Enter your license below and click Next Make sure you have a working internet connection before doing this If internet is missing the program will enter the test mode License Internet Proxy 35 Then Select your Manufacturer Cutter model and Connection method Sian ut Choose Cutter Communication method Choose Manufacturer Copam Choose Cutter Copam CP 2500 Choose Device Keyspan USB Serial Port C v Setup will then be completed and you will be taken to the main SignCut screen pa Soe Oe HQ y Y We can now let SignCut run in the background while we do our design work in Inkscape or another preferred vector image software We will return to SignCut once we are ready to cut To open Inkscape simple loca2. Back View Pinch Rollers Pinch Rollers Holds the media tightly to the feed roller below Back view shown in detail below Detail of Pinch Roller Back View Tension Screw Adjusts the tension of how tightly the pinch roller is held to the feed roller below Release Lever Release Lever Allows you to release Pinch Rollers either so they can be moved from side to side or to allow media to be easily fed N below them by pulling up on the Release Levers i 1 Vi gt Fr Control Panel Measure Screen PAPER TYPE SCROLL SHEET The Measure Screen is the first screen that you will see when starting up the cutter Select your media type from the menu and then confirm your selection The cutter will then measure your material and report the cuttable area in millimeters on the Paper Size Screen Next If Scroll is selected only the width is measured If Sheet is selected than both the width and length of the material will be measured Left Right Selects between the Scroll and Sheet media types If you are cutting from a single sheet Buttons of media select Sheet If you are cutting from a roll of media select Scroll Enter Button Confirms the selection between Scroll and Sheet All other buttons have no function on this screen Paper Size Screen PAPER SIZE 410 Y 840 The Paper Size Screen will display after a measurement ha
3. Shift Ctrl S Save a Copy N Shift Ctri Alt 5 Select a name and location for your file Here we have chosen the name USC_logo and are going to save to our desktop Name USC_logo Browse for other folders exc Then select Encapsulated Postscript eps from the drop down menu at the bottom of the window Inkscape SVG svg Plain SVG svg Compressed Inkscape SVG svgz Compressed plain SVG svgz PostScript ps Encapsulated Postscript eps POF via Cairo pdf N PostScript via Cairo ps Enhanced Metafile emf PovRay pov export splines OpenDocument drawing odg LaTeX With PSTricks macros tex Desktop Cutting Plotter DXF GIMP Palette gpl Microsoft XAML xaml Compressed Inkscape SVG with media zip Guess from extension Inkscape SVG svg v For a simple design you will most likely not need to check any of the boxes in the Encapsulated Postscript window Uncheck all boxes and select Ok f 31 Encapsulated Postscript Make bounding box around full page _ Convert texts to paths Embed fonts Type 1 only Now that the image is vectorized and saved the cutting process is the same as it is for cutting a simple image You can now follow the steps from the Cutting a Simple Design in SignCut section of this manual starting on page 41 to make your cut 46 Specifications
4. US Cutter Contents A A ee ee RE oR sn ne RESO na nya el ge ean 3 Cutter Pasa AS net ah nth alse tal ede cna id 4 PLONE VIEW Atoll ladrar ica lolas 4 DetaloCar SANS 5 FRI CSIC VEIA AA 5 Back Vi Wasi 6 Det ie iC Roller siria dao iba 6 COME in 7 NS ASUS CESEN a a aa 7 A ule sere reteset rn ene net a aren nee Teens cee eee sent ere ene ee 7 eos A A ee ee 8 A O a DURA a Ng aOUEA a 9 ek cairo ler E eet ron eer cen ee ti ote ert iia 10 E AP A A A eienenns 11 SENO A hgaae shel a GRS aaa nant ae da AG a aaa enact NSE 12 eCelt celui area a Locion dor tne CUE O teeter erent tren eee eters 12 Connecting the Cutter toa COMPUTER 12 linstalline ion Bl 7S SOM ware AAA AA 14 Lins talline SiC Ut SOM War G tina 15 lnstan a Ney blade opnlew aaeat ta cmines uaainose neanaanesaboouenuatian seen anaiee tac 16 Replacing a Worn Blade cronica oda ARA NAS 17 Installinoa Pen Carrasco 18 Repara or CACAO a 20 DEEP by Step TAS CUCU O INS ni 25 tanto pion Blazer tor thie inst ln apenas dura Delon 25 Making a Simple Catia Sin BIA Zor iO AAA AAN 27 aporte STO BIA ZO eN IO 29 Converting a Raster Image to Vector Image in SignBlazer va cisasssssssasesidecapasnnssd condenses bavbsasdeddnasiatanhacddentragartasiats 32 Starting SidnCut and Inkscape tor the First iaa 35 Creating Simple Design RSS AAN e 37 Cutting a Simple Destinia Sion CU 41 Convertin
5. Maximum Paper Feed Width Maximum Cutting Width Cutting Speed Pressure Range Maximum Cutting Thickness Coordinate Origin Number of Cutter Pen Standard of Blade and Holder Material Maximum Velocity Programmable Resolution Distance Accuracy Repeatability Command Sets Interface Processor Memory Drive Lifting and Dropping Rate Acceleration Power Consumption Customer Service Technical Support Line Online Technical Support Customer Forums Manufactured For and Sold Directly By CP 2500 24 inch model 24 inches 610mm CP 3050 35 inch model 36 inches 915mm CP 4050 48 inch model 48 inches 1220mm CP 4500 54 inch model 54 inches 1370mm CP 2500 24 inch model 23 2 inches 592mm CP 3050 35 inch model 35 inches 890mm CP 4050 48 inch model 46 9 inches 1190mm CP 4500 54 inch model 53 2 inches 1350mm 4 24 Inches per second 100 600 mm per second In 4 inch per second 100mm per second increments 50 500g In 10g increments 04 inches 8mm Coordinate origin specifiable 1 F2 Calendared self adhesive vinyl film fluorescent film reflective film paper card or other materials of thickness between 0 05 0 30mm 0 025mm Step 0 05mm Step Within 0 15 of distance moved Within 0 02mm Compatible with HP GL Centronics parallel RS 232 serial auto interface recognition Adapt 16 bits DSP technology 64Mb Memory Divisional motor 1 5times sec 3 110v 250v 50 60HZ 120W max
6. Inkscape you should have only one color If you are working from another file you could have many different colors Since we are making a simple cut no other settings or options need to be adjusted here We can simply click on the Cut Out button from the left menu to open the Cut Out window Cut out Shortcut 4 Then press the Cut Out button from the Cut Out window to make your cut Cut out Cutting Advanced settings Tiles Copies settings Calculated vinyl consumption Copies u JLo Distance between copies tiles k Stack copies tiles Cut equal tiles First E E El El Use weeding Frame If your design has multiple colors replace the vinyl in your cutter with the color you wish to cut select that color from the color selections on the right and repeat for each color 42 Converting a Raster Image to Vector Image in Inkscape If you already have designs finished that need to be cut and are in a vector format such as di eps svg etc you can cut them by following the instructions in the previous section Cutting a Simple Design in SignCut If they are in a raster image format then they can be converted to vector for cutting depending on their level of detail g r g aep g The difficulty of converting a raster image to a vector image will vary greatly depending on the amount of contrast in the image The portion of the image to be cut should be darker than the background or s
7. Instructions Starting SignBlazer for the First Time Open the SignBlazer Software The Default location will be in the Programs Folder under SignBlazer Elements for USCutter fin SionBlazer Elements For USCutter 8 SignBlazerS S HotShot Demo Version SI SignBlazer Elements for USCutter SignBlazer News And Updates A a Uninstall or Modify or Repair SignBlazer Elements for USCutter Navigate to this folder and select SignBlazer Elements for USCutter SignBlazer will attempt to download update files is SignBlazer LiveUpdate Downloading updated files Please wait while Setup is downloading updated files to your computer File Speed Status Getting file information Elapsed Time Remaining Time Current File PO Overall Progress 29G When it fails cancel the update process By Pressing the Cancel button on the error window and then OK on the confirmation window and the program will start regularly To override the update process in the future refer to the Troubleshooting listing titled When starting the SignBlazer Software it fails to find updates located in the Troubleshooting section of the manual starting on page 48 Error sending request The server name or address could not be resolved A File download failed or was cancelled by the user SignBlazer LiveUpdate will exit and will not attempt to download files again before tommorow lx We will be working in Tr
8. Preview Brightness cutoff Threshold 0 500 2 Edge detection Threshold 0 650 2 Color quantization Colors 8 an C Invert image Multiple scans creates a group of paths O Brightness steps EJE US Cutter y Colors O Grays V Smooth Stack scans _ Remove background Credits Thanks to Peter Selinger http potrace sourceforge net Late 2 Nae Make sure the Brightness cutoff radio button is selected Now you can adjust the Threshold level by inputting a number between 0 000 and 1 000 in the Threshold box adjacent from the Brightness cutoff button The number you select will determine how much of the image will be included in the vector conversion which is to become the image that will be cut Anything darker than the level set on the Threshold slider will be included in the cut and anything lighter will not Since we chose an image with good contrast and separation for our example this process will be easy We will set the Threshold level to 500 and click the Ok button If you are unsure where to set your Threshold amount then you can try different values and then use the Update button at the bottom of the preview panel to generate a preview 44 Then close the Trace Bitmap window by pressing the close button on the top right of the window If you are unsure what amount to use you can try a variety of numbers and preview how the vector image will look by pres
9. pen carriage Replace the carriage cap and screw into place A Once you are familiar with the cutter and its basic functions install the blade carriage next sesa eth 19 Preparing for Cutting If you are going to cut from a scrap or single sheet instead of a roll then skip the next step on placing a roll All other steps will be the same R Place the roll of media on top of the stand rollers Release the Pinch Rollers by pulling up on the Pinch Roller Release Levers 20 Feed the media through the back of the machine underneath the pinch rollers if working from a single sheet instead of a roll the material can also be fed from the front Adjust the pinch rollers so there is one roller located on each side of the material and on models with 3 or more rollers one roller near the center Only lower the pinch rollers where there is a feed roller below Use the Feed Roller Guides page 4 to determine placement of feed rollers DD th URA 291 Leave a gap of between Y2 1 12 from the edge of the roller and the edge of the material on both sides Make sure that the pinch rollers are only lowered where there is a Feed Roller below The front of the pinch roller should always be placed along a Feed Roller Guide to made sure that there is a Feed Roller below Engage the Pinch Rollers by pushing down on the Pinch Roller Release Lev
10. reset the origin you must hold the Enter Button for 2 seconds below Enter Button Holding the Enter Button for 2 seconds will reset the origin of the cutter The next held down cut that takes place will be made from this new origin location All other buttons have no function on this screen 10 Pause Screen PAUSE SETUP ABORT The Pause Screen is accessed by pressing the pause button while to cutter is cutting From the Pause Screen you can enter the Setup Screen to change the main settings of the cutter cancel the current cut or exit the pause screen and continue cutting You can also move the loaded material forwards or backwards though doing so after a cut has begun is not recommended Setup Enters the Setup Screen page 9 Allows to you to change the cutters main settings If a test cut is made from the Setup Screen the current cut will be canceled Abort Cancels the current cut and returns to the Function Select Screen Page 8 When you cancel a cut from the cutter you should also be sure to cancel the cut from the cutting software on your computer Pause Button Left Right Arrow Buttons Enter Button Up Down Arrow Buttons Exits the Pause Screen and resumes the current cut Selects between the Setup and Abort options Confirms the selection between Setup and Abort Moves the loaded media forwards and backwards similar to the Up Down arrow buttons on the Jog Screen pa
11. the parameters of the selected setting Arrow Buttons Enter Button Accepts the changes made and returns to the Function Select Screen If you accessed the Setup screen from the Pause Screen the Enter button will return to the Pause Screen Test Button Cuts a small test pattern to demonstrate the current settings of the cutter and allows you to see if they are appropriate for your current material After the test cut has been made the cutter will return to the Setup Screen and further changes can be made If you cut a test shape after entering the Setup Screen from the Pause Screen the current cut will be canceled before the test cut is made All other buttons have no function on this screen Jog Screen CURRENT POSITION DY The Jog Screen is where the cutter and the material loaded in the cutter can be moved to create a new starting location for the next cut to take place from The X and Y values on this screen will show the amount of movement that has taken place in relation to the initial origin of the cutter You will only be able to move the cutter within the cuttable area that has been determined when the material was measured by the cutter Left Right Moves the Carriage Arm from side to side Arrow Buttons Up Down Moves the material forwards and backwards Arrow Buttons Enter Button Pressing the Enter Button will return to the Function Select Screen but will not reset pressed the origin of the cutter or material To
12. y Stroke paint 2 Stroke style x OH vw Flat color RGB HSL CMYK Wheel CMS lt gt lt gt lt gt RGBA 441717Ff Blur J 0 0 Al Opacity _ 100 0 py Use the R G and B sliders from under the RGB tab to select a color for the object This is the color the object will appear in SignCut Here we have chosen a dark red with values of R 68 G 24 and B 24 Make sure the alpha slider A is set to 255 38 Now from the Stroke Paint tab select No Paint y FI Stroke paint stroke style moO No paint The object is now ready to be saved so that it can be opened and cut from SignCut Select File gt Save As from the top menu Edit View Layer Object Path New e Open Ctrl O Open Recent Revert Save Ctrl S Save a Copy gt Shift Ctri Alt 5 Select a name and location for your file Here we have chosen the name rectangle and are going to save to our desktop rectangle 39 Then select Encapsulated Postscript eps from the drop down menu at the bottom of the window Inkscape SVG svg Plain SVG svg Compressed Inkscape SYG svgz Compressed plain SYG svgz PostScript ps Encapsulated Postscript eps PDF via Cairo pdf PostScript via Cairo ps Enhanced Metafile emf PovRay pov export splines OpenDocument drawing odg LaTeX With PSTricks macros tex Desktop Cu
13. 425 481 3555 Available 7am 5pm Mon Fri support uscutter com E mail support USCutter com forum uscutter com UWSCutter7 19510 114 Avenue NE Suite C 1 Woodinville WA 98072 425 481 3555 phone 888 640 0720 fax www USCutter com ayy Troubleshooting The cutter is unresponsive to Communication issues can arise if the cutter was powered on while communications from the the software is trying to send data to the cutter This is most computer and software common when using SignBlazer software Exiting the cutter screen of SignBlazer and returning to the main SignBlazer screen may resolve this issue If not save all work and try exiting SignBlazer and restarting with the cutter powered on It is good practice to start SignBlazer with the cutter powered on to avoid communication problems Make sure that your output device setting on your software is set to the correct COM LPT port Found by selecting File gt Cutter from the menu on the main SignBlazer screen and then selecting Setup from the top menu buttons or by selecting Settings gt Cutter in SignCut Your port can be found by following the instructions in the Finding Your COM LPT Port section of this manual on page 14 You can change your COM Port by right clicking on the COM Port in the device manager and going to the advanced section of the Port Settings tab Adjust your Flow Control settings to Hardware by first locating your COM LPT Port in the device manager
14. By following the instructions on page 14 then right click the Port and select Properties On the Port Settings tab change to Flow Control option to Hardware Try a different connection method between your cutter and computer If another connection method is not available try a different cable serial parallel USB to connect from the cutter to computer Also try the current cable on another device to test if the problem is from the cable Replace if necessary The cutter performs erratically Some computers do not work well when connected via the USB during cuts stops cutting port of the cutters If you are having problems while cutting and before the cut is finished or are using the USB cable to connect from your cutter to computer cuts lines that do not appear in you may wish to try the serial cable connection to avoid further the design problems If a serial cable connection is not available on your computer you can try a third party USB to serial connecter or a PCI card serial adapter for your computer 48 When starting the SignBlazer Software 1t fails to find updates Cuts are jagged or inconsistent Slashes are made across the vinyl from the blade movement during cutting Plotter does not power on The measurements of the media are inconsistent incorrect This is a regular occurrence of the SignBlazer software and should not be considered a problem All features of the software will continue to work in trial mode
15. T Port on the next page but for most users the port will be 1 i e COM1 LPT1 If Using the USB Cable to connect your cutter to a Computer You will need to install drivers for the USB connection to work properly These drivers can either be obtained from the supplied drivers disc or downloaded from the support website in the downloads section of support uscutter com Mac Users will need to download drivers from the support website as the drivers included on the disc are Windows only Windows XP Users Insert the driver disc or download and unzip if necessary drivers to your system Connect the USB Cable to your computer and your cutter The Found New Hardware wizard will appear When asked Can Windows connect to Windows Update to search for software select No not this time and click next When asked What do you want the wizard to do select Install from a list or specific location Advanced and click next Choose the Search for the best driver in these locations radio button and check the Include this location in the search checkbox Now type or browse to find the location of the downloaded drivers inserted drivers disc and click next When the wizard is complete click the Finish button The Found New Hardware wizard should appear again When it does follow steps 3 6 again for the second driver Windows Vista Users If you want to use downloaded drivers download them be
16. and the Inkscape software will be downloaded Follow the Inkscape installation instructions SignCut installation will be temporarily paused When you are finished installing Inkscape SignCut will resume installation and finish Installation is now complete 4G Installing a New Blade Unscrew the Set Brass Ring cap from the on Blade Blade Carriage to the carriage fully down position UN HU LALITA A Remove the protective cover from a New blade Insert the blade into the top of the Blade carriage f Screw the cap back onto the blade carriage Adjust the carriage cap until the blade is protruding approximately 1 64 ofan inch Adjust the Brass Ring until it fits snug against the Cap This will help keep the cap in place during operation gt DD Ene This distance will vary depending on what material you are cutting Your blade depth should be adjusted to approximately The height of your cuttable material 4 of the height of the backing material psss Cuttable Material Vinyl Backing Material This will allow the blade to fully cut the material without fully penetrating the backing 1 64 of an inch is a general guide that will work well with many common vinyl products and is a good starting point for determining the blade depth for your mater
17. draw in outside dust from the area surrounding the cutter Excessive buildup of dust can cause either mechanical or electronic malfunctions Keeping the cutter as dust free as possible will help ensure trouble free operation Try to find an area for the cutter that will be free of any excessive dust and use the supplied cover when not in use All cutters will produce a small amount of noise while operating Please take this into consideration when selecting a location for your cutting purposes Do not remove the grounding plug from the power cord or attempt to use the cutter when it has not been properly grounded Use all available wheel brakes on the cutter stand to reduce movement during cutting Keep the cutter away from liquids heat sources and strong magnets Connecting the Cutter to a Computer Attach the power cord to the cutter and then plug in the unit and turn on the power If Using the a Serial or Parallel Cable to connect your cutter to a Computer AO If you are using a Serial or Parallel Cable to connect your cutter to a computer then no further setup is necessary Simply connect one end of the cable to the cutter and the other end to a computer and setup is complete If you have more than one serial parallel connection on your computer or you are experiencing communication issues between your cutter and computer then you may wish to verify that the correct port is being used in your software setup see Finding Your COM LP
18. e viewed changed Has no function on this screen Has no function on this screen when used alone Can be used with the right and left arrow keys to perform advanced functions below When the Enter Button is pressed simultaneously with the Left Arrow Button a detailed test cut is made This detailed test cut can be used to test the current settings of the cutter when the small test pattern is not sufficient for testing and also for more advanced troubleshooting When the Enter Button is pressed simultaneously with the Right Arrow Button a repeat cut is made of the last cut that was sent to the cutter This is a simple way to make duplicate cuts of the same design The repeat cut function will only retain the last cut information until the cutter is powered off When the cutter is powered off the last cut information is removed from the cutter memory and the repeat cut function will not be available until a new cut has been made Pressing any of the arrow buttons will access the Jog screen of the cutter Page 10 where a new starting position can be entered for the next cut Setup Screen SPEED FORCE OFFSET 60cm s 54g 0 25mm The Setup screen allows you to view adjust the main settings for the cutter You can adjust the speed at which the cutter moves while cutting the amount of force used to make cuts and the blade offset which compensates for slight variations in blade sizes You can also make a test cut to see if any of the s
19. ers If the cutter is not already on turn it on and select your media type Scroll or Sheet from the Measure Screen to find the cuttable area of your material If the cutter is already on go to the Measure Screen and select your media type Scroll or Sheet from the Measure Screen to find the cuttable area of your material 299s If you would like to change the position of where the cut will be made Enter the Jog Screen of the cutter directions for changing menu screens are located in the Control Panel section of the manual starting on page 7 Adjust the vinyl to where you want the cut to start by using the Up and Down Arrow Keys on the Control A o Y Panel V UV VV VV VV VV VV VY Now adjust the Blade to where you want the cut to start by using the Left and Right Arrow Keys xX 23 Now hold the Enter button until the origin of the cutter is set This is the location where the next cut will begin When choosing a starting location on your cutter remember that the process will start in the bottom right area of the design Please leave enough room to the left of and above the starting location to finish your cut If you would like to make other adjustments to the pressure speed or other settings you can do so now If you are setting up for your first cut with the machine then the default values should be a good starting point 24 Step By Step
20. ettings need to be changed or to check if the changes you are making are improving cutter performance Speed Setting The Speed Setting will adjust the rate at which the cutter operates while cutting On smaller or more detailed designs the speed should lowered to increase the precision of the machine On larger or less detailed designs the speed can be raised to decrease cut time Force Setting The Force Setting will adjust the amount of pressure that the blade uses when cuts are being made by the machine This setting should be used in conjunction with proper blade depth page 16 to allow the blade to fully cut the material but not cut through the protective backing material of your selected media Your blade depth should be adjusted to approximately The height of your cuttable material 14 of the height of the backing material This will allow the blade to fully cut the material without fully penetrating the backing Once you have blade depth properly adjusted change the pressure setting until you are getting smooth cuts Offset The Offset Setting allows the cutter to adjust for slight variations in different blade sizes If your cuts are not fully closing or are overlapping you can adjust the Offset Setting to correct it Standards for blade offsets are often found on the packaging of or in the instructions that come with the blade Left Right Selects the setting to be changed Arrow Buttons Up Down Adjusts
21. fore starting the install process Connect the USB Cable to your computer and your cutter The Found New Hardware wizard will appear a When told that Windows needs to install driver software select Locate and install driver software recommended If Windows finds and downloads your needed drivers then the process is complete Repeat the previous steps again for the second needed driver If Windows does not find and download the needed drivers proceed to the next step If you are going to install the drivers from the disc insert it when advised by Windows If you are going to use downloaded drivers select I don t have the disc Show me other options Browse to the folder where the drivers are stored and click next When the wizard is complete click the close button The Found New Hardware wizard should appear again When it does follow steps 2 6 again for the second driver If you are using another version of Windows or a Mac OS and require specific instructions for installing the drivers they can be found at ftdichip com Documents InstallGuides htm 2432 Once your drivers are installed you will need to make a note of the COM port that has been assigned to your USB Cable connection Finding Your COM LPT Port First navigate to the Device Manager by following the below instructions for your operating system Windows 95 98 Me Users Click Start then select Settings gt Control Pane
22. g a Raster Image to Vector Image in Inkscape A Aah ai AS Utah oath Atak Dasa ERE AEE TAE T 43 Specifications A EEEE AEE AE AEAEE A EA nee 47 Troubleshooting E a A eee 48 Welcome Thank you for choosing a Copam cutter from US Cutter The Copam cutters provide a professional level high quality cutting experience for a fraction of the cost of most cutters of this quality This manual is here to help provide a starting point in the learning process of the Copam cutters or to vinyl cutting in general Please read it thoroughly and follow the steps carefully to help insure a trouble free experience with your new machine If you have any questions along the way we have provided a few locations to go to get those questions answered You can post on the US Cutter forums at forum uscutter com submit a request for support on the support website at support uscutter com or call customer service at 425 481 3555 We hope you enjoy your experience with your new cutter and the US Cutter family Cutter Parts Before you start cutting you should familiarize yourself with the cutter and its basic parts and functions Front View Right Side Cover Feed Roller Guides Control Panel Carriage Arm Pinch Rollers Control Panel Used to provide input directly to the cutter Covered in detail in the Control Panel page 7 section of this manual Carriage Arm Holds the Blade or Pen Carriage Shown in detail on page 5 P
23. ge 10 Moving the material after a cut has started is not recommended 11 Setting up If you are setting up for the first time please take a moment to refer to the Packaging Guide to take account off all the included components and accessories For help with Stand Assembly please refer to the included instructions Selecting a Location for the Cutter The first step to setting up your cutter is finding a good location for the machine Consider these factors when you are selecting a suitable place You will need to have access to both the front and rear of the machine for operations as well as for loading and unloading new vinyl rolls Try to find a space with adequate access to both the front and back of the machine Since your cutter is a precision cutting device you will want to find a location that will be stable to insure cutting accuracy Whether placing the unit on the stand a floor or a table top the accuracy of the machine will be directly related to the stability of the platform it is placed on Find a sturdy floor space or table top for the machine and consider a location that will be out of the way of people and other machines with moving parts while the cutter will be operating Excessive moving of the machine can not only disrupt accuracy of cutting but may also cause electrical components inside the machine to dislodge and require otherwise unnecessary repairs and maintenance Fans located inside of the cutter can
24. ges imported vid Clipboard Paste may not retain the same dimensions that they held in another software program Using the Import Function You can import an image that has been saved from another program by first selecting Import from the File drop down menu Then navigate to the saved file by using the Folder and Drives menus 30 Folder C DOCUMENTS AND SETTINGS ES c gt Documents and Settings E gt Administrator Desktop zj New Folder Then Select the image to import USCutter7 R USCutter_Logo ipg And select the OK button ok If you are having trouble locating your file make sure that the file type is selected from the List Files of Type menu or that All Graphic Files is selected List Files of Type All Graphic Files If the file imported is already a vector image then it is now ready to cut or be further edited within SignBlazer If you are ready to cut you can follow the steps in the previous section Making a Simple Cut in SignBlazer starting on page 27 If the image imported is a raster image then follow the steps in the next section Converting a Raster Image to Vector in SignBlazer to further prepare the image for cutting Ls Converting a Raster Image to Vector Image in SignBlazer The difficulty of converting a raster image to a vector image will vary greatly depending on the amount of contrast in the image The portion of the
25. ial but some adjustments fine tuning to blade depth will be necessary in most cases s16 Loosen the locking knob on the Place Blade carriage into the Tighten the locking knob on the carriage arm carriage arm O Replacing a Worn Blade carriage arm First remove the blade carriage from the carriage arm Unscrew the cap of the blade carriage E Carefully pinch the blade on both sides and pull it up and out of the Blade Carriage ets Follow the steps from Installing a New Blade on the previous page 17 Installing a Pen Carriage Optional Many new users will benefit from practice cutting with the optional pen carriage until they are comfortable with Ly P g P P g y normal operations of the cutter and cutting software Your Pen Carriage should come assembled and appear as it does in this image If it does not please refer to the pen replacement section below for assembly instructions To install the pen carriage Loosen the locking knob on Drop the pen attachment into Tighten the locking knob on the carriage arm place in the front slot of the the carriage arm carriage arm A O S O To Replace the pen or spring inside of the Pen Carriage Unscrew the top cap from the Pen carriage 1d A 18 Remove the top cap the pen and the spring Replace the pen and or spring as necessary Slide the spring onto the pen from the top and insert it back into the
26. ial Mode Select Trial Mode from the following screen then select Yes from the confirmation window Mr USA yg A Accept Activation Code 296 Now SignBlazer is open and you are looking at the main SignBlazer screen Re OS E FW BD Cx 22 GE CH CRS E GE E R 9 Pe tN I ELA E AAA EPA E J A as ss Ass das 1 A A 14 10 a di BE SRS a ee 088 71 78 AAA AA A EPA ke Scenes YiHoez Grid 0 30 Snap Making a Simple Cut in SignBlazer You can create images from scratch using the various tools in SignBlazer For this tutorial we will be drawing a simple square just to show the steps of making a cut from SignBlazer Select the Square tool at the top of the window 27 Now draw a square by clicking first in the main And then moving the mouse to determine the size window of the square desired and clicking a second time Now to cut this simple shape from the cutter Select Cutter from the top selection menu Arrange Text Image Tools Settings Help Circle Cutt Polyline This will take you to the cutter screen of SignBlazer Elements where you can see a representation of how your cut will be made when sent to the cutter as well as various cutter options AGA GP amp P C2 bit lll wi GA Vatani Saeki savi OO Oiuka A Vortec 1 Keep prepertional p Y 28 Since this is a simple cut no adjustments need t
27. image to be cut should be darker than the background or surrounding area and should have a significant amount of contrast and separation from the rest of the image If possible the image should be completely separated from the background and be black in color though the image we chose for this demonstration has a background and is not completely darkened to demonstrate that the process is possible with a variety of images First make sure that the image has been properly imported into SignBlazer and that the image is selected You can tell an image is selected when it shows a border and square bounding boxes around its parameter With the image selected select Monochrome 1 bit from the Mode section of the Image drop down menu Image Tools Settings Help e Scan Acquire Y ESE exons Scan Select Source A n ES GE ORs Indexed 8bit nes Grayscale om Sometimes an imported image will already be in monochrome but will still need to be vectorized before being cut If the image imported is monochrome than you can skip this step ae ae The Convert Image to monochrome window will appear Convert image to monochrome 1bit per pixel Threshold Level Y Now you can adjust the Threshold Level slider Where you place the slider will determine how much of the image will be included in the monochrome conversion which is to become the image that will be cut Anything darker
28. inch Rollers Holds the media tightly to the feed roller below Shown in detail on page 6 Feed Roller Guides Shows the location of each feed roller so that the pinch rollers can be properly positioned to make contact with the feed rollers Feed Rollers Positions the cutting material during operation Not Pictured Located below each Feed Roller Guide Right Side Cover Contains the Power Switch and the Parallel Serial USB and Power cable ports for the cutter Shown in detail on page 5 Detail of Carriage Arm Blade Pen Carriage Slot ES Ka N la Locking Knob Right Side View Parallel LPT Cable Port Serial COM Cable Por Power Cable Port USB Cable Port Blade Pen Carriage Slot Locking Knob Parallel Cable Port Serial COM Cable Port USB Cable Port Power Cable Port Power Switch Holds the Blade or Pen Carriage in place Allows access to the Blade Pen Carriage Slots for exchanging replacing Carriages Used to connect a parallel cable from the cutter toa computer Used to connect a serial cable from the cutter to a computer Used to connect a USB cable from the cutter to a computer Used to connect a power cable from the cutter to a wall outlet or surge protector Main power switch for turning the power of the cutter on or of f 0 Only one of the connection cables should be used to connect the cutter to d computer
29. l Select Device Manager Windows 2000 XP Users Click Start Then Right click My Computer then select Properties Select the Hardware tab Click the Device Manager button Windows Vista 7 Users Click Start Then in the Start Search box Type Dev without pressing enter wait for a list to show up Click Device Manager Expand the section labeled Ports COM amp LPT Make a note of which number COM LPT Port is associated with your cutter You will need this information to properly install your software Installing SignBlazer Software Insert the SignBlazer Elements CD into your computer Select Run Setup Follow the on screen instructions Ignore the warning of only being able to install SignBlazer on one computer This does not apply since you will be using trial mode and updates are no longer available for the SignBlazer software When asked what cutter you want to use select the model that matches your Copam cutter 2500 4050 or 4500 When asked if you want to install the USB driver select No since we have already done so 14 When asked what port your cutter uses select the Port that corresponds with your setup If using a USB connection you will need to select the COM port that corresponds with your setup Noted above from the Finding Your COM Port section of the manual Make sure that your Baud Rate option is set to 9600 Do not change the Data Bits Stop Bits or Parity
30. o be made here We can tell the software we are ready to cut by pressing the cut button in the top selection menu and then pressing Cut Tile in the Cut Tile window Cut Tile Next Tieto Cut fh 4 Tile Size 0 40 x 0 40 VY Pause between tiles Ima Skip Tile Cancel l Home Position Move Cutter to Maximum Pos When you are finished you can go back to the main SignBlazer screen by pressing the Finish button in the top selection menu 2 El CUT Curl AnS Frevious Importing in SignBlazer Drawing images from scratch in SignBlazer may prove to be somewhat different than imaging software that you are more familiar with If you would rather create the images to be cut in another software or you already have designs finished that need to be cut then you can just import the finished artwork into SignBlazer and cut from there Most major raster and vector image files are supported in SignBlazer Elements including dxf eps ai bmp tif gif pcx tga jpg pcd pct psd cmx ps and wmf 250 You can import to SignBlazer one of two ways Using the Clipboard You can import from the clipboard by first copying or cutting an image opened from another software program and then placing it into SignBlazer by selecting Clipboard Paste from the Edit drop down menu Edt Manipulate Arrange Text Image Tools G 0 Delete Alt Bksp Ctrl Z Ima
31. options Make sure the Flow Control option is set to Hardware Installing SignCut and Inkscape Software If you will be using the SignCut software to cut from your computer you will also need a vector design program SignCut is strictly a cutter interface and cannot be used to create signs and designs The instructions in this manual will give directions for using Inkscape A popular free vector design program with SignCut but directions for other software will be mostly the same If you prefer creating vector graphics in Illustrator CorelDraw or another vector graphic design program then you can choose to not install Inkscape and work with your preferred software Go to www signcutpro com bundle html Fill out the form and click Register You will be directed to a page where you will be given a download link and a license number Save this page or print it for reference A copy of this page will also be sent to the email address used while filling out the Registration form Follow the link to the web address that corresponds to your operating system and download the SignCut software installation program After the SignCut software installation program has been downloaded run the program and follow the on screen instructions You will be asked if you would also like to download Inkscape If you have not already done so and you would like to use the Inkscape software as a vector design program select the yes button
32. s been made from the Measure Screen This will display the cuttable area that the machine has detected for your media in millimeters You can record the dimensions and use them as a reference on your cutting software to ensure that you are creating designs that will fit within the cuttable area of your material Enter Button Exits the Paper Size screen and continues to the Function Select Screen Next All other buttons have no function on this screen Function Select Screen FUNCTION SELECT The Function Select Screen is the main screen for the cutter From this screen you can access the Measure and Setup Screens make test cuts make a repeat cut of the last cut made by the cutter or adjust the origin of the of the next cut to be made Measure Button Test Button Setup Button Pause Button Enter Button Enter Button Left Arrow Button Enter Button Right Arrow Button Up Down Left Right Arrow Buttons Accesses the Measure Screen page 7 where the material loaded in the cutter can be measured and the size of the cuttable area can be displayed Cuts a small test pattern to demonstrate the current settings of the cutter and allow you to see if they are appropriate for your current material After the test cut has been made the cutter will display the Setup Screen page 9 to allow the option of changing any settings Accesses the Setup Screen page 9 where the main settings of the cutter can b
33. sing the Update button below the Preview window There are many different ways to get a vector image from a raster image We have chosen to show one of the more common and simpler variations Some images will not be easily converted directly from raster image to vector or will require extra editing during the conversion process You are now left with 1 rasterized image and 1 vectorized image This may be difficult to see as they are layered directly on top of one another If you grab one image and drag it you will see the other image left behind You should now delete the rasterized image that has been left behind as it is no longer needed and could cause problems when you try to open the file in SignCut Select the rasterized original image Then select Edit gt Delete from the top menu to delete it Edt view Layer Object Path Te Undo Move Ctrl Z Redo Delete Shift Ctri Z lt 7 Undo History Shift Ctrl H de Cut Ctrl X Copy Ctrl C C Paste Ctrl V Paste In Place Ctri Alt Y ha Paste Style Shift Ctrl Paste Path Effect Ctrl 7 Paste Size b a Eind Ctrl F J Duplicate Ctrl D Clone gt re Make a Bitmap Copy Alt B E Delete OS Del s45 s The object is now ready to be saved so that it can be opened and cut from SignCut Select File gt Save As from the top menu File Edit View Layer Object Path New e 3 Open Ctrl O Open Recent e Revert la Save Ctrl S E Save As
34. te the icon in your programs menu and open the program No further setup will be required 226 Creating a Simple Design in Inkscape You can create images from scratch using the various tools in Inkscape and then cut them from SignCut For this tutorial we will be drawing a simple square just to show the steps of sending files from Inkscape to SignCut and then making a cut Select the Square tool from the left of the main Inkscape window Qe 2 Create rectangles and squares F4 Now draw a rectangle by clicking and dragging the mouse in the main window then releasing when the desired size is met Now click on the Fill and Stroke button at the top of the screen to edit the shape In the Fill and Stroke panel we will edit the colors of the shape to make it more identifiable once we get to the SignCut program To edit the Fill and Stroke properties of the rectangle make sure that it is selected If you haven t made any other shapes or made any other changes in Inkscape it should still be selected If it is selected you should see a dotted border a7 surrounding the shape with a square symbol in two of the corners and a circle in another like the image below If the shape is not selected make sure you are still using the square tool and click on the shape to select it Select the Fill tab from the Fill and Stroke panel Then select Flat color from the options at the top of the panel
35. than the level set on the Threshold slider will be included in the cut and anything lighter will not Since we chose an image with good contrast and separation for our example this process will be easy We simply check that our image to be cut shows up in light grey or black and that there are no areas of the background or other parts of the image that are unnecessarily included Now press the OK button on the Convert Image to monochrome window Now to convert a monochrome image to a vector select Vectorise from the Image drop down menu Image Tools Settings Help e Scan Acquire e Scan Select Source y Mode gt 233 ImageCut 33 And press the OK button on the Vectorise Image window Vectorise Image Setup Logos Art 2 General v E Help gt Y S HIST pa Ex Bike TIF Victoria TIF l y Y A Color Vectorization Overlay Colors 3 Inset Colors Saab2 TIF l You are now left with 1 monochrome image and 1 vectorized image This may be difficult to see as they are probably layered directly on top of one another If you grab one image and drag it you will see the other image left behind You can now delete the monochrome image that has been left behind as it is no US Cutter7 The cutting process for a vectorized image is the same as it is for cutting a simple image You can now longer needed follow the steps from the
36. the problem is from the power cord Replace if necessary The cutter uses light sensitive sensors to detect where your cuttable media is placed If the cutter is placed near a strong light source the sensors can act erratically Try to redirect any strong light sources that are close to or pointed towards the cutter The width measurement is made from the distance of the two outer pinch rollers If you are getting an unusually inaccurate width measurement make sure that the 2 outer pinch rollers are set on the edges of opposite sides of the material page 21 Other troubleshooting solutions may be found by visiting the Customer Forums or Technical Support Website or by calling the Technical Support Line Web page addresses and Phone number on the specifications page 47 49
37. tting Plotter DXF GIMP Palette gpl Microsoft XAML cami Compressed Inkscape SYG with media zip Guess from extension Inkscape SVG svg For a simple design you will most likely not need to check any of the boxes in the Encapsulated Postscript window Uncheck all boxes and select Ok In the next section be cut Encapsulated Postscript Make bounding box around full page _ Convert texts to paths Embed fonts Type 1 only C Cutting a Simple Design in SignCut we can open our file and send it to the cutter to 40 Cutting a Simple Design in SignCut In SignCut Select File gt Open 9 SignCut Productivity Pro File Edit Special cutting Settings Help Open Save as N Preview one copy Cut out Close Locate your file in the window and select Open Open JEI Look in Desktop 5 rectangle eps My Recent Documents Desktop a My Documents My Computer wo d File name rectangle eps My Network Files of type All supported formats WOoanrDES Please make sure that your cutter is on and ready to cut before proceeding See the Preparing for Cutting section of the manual page 20 41 Select the color that you would like to cut from the color selections on the right oor rr i a R 66 G 23 at If you are following from the previous section Creating a Simple Design in
38. urrounding area and should have a significant amount of contrast and separation from the rest of the image If possible the image should be completely separated from the background and be black in color though the image we chose for this demonstration has a background and is not completely darkened to demonstrate that the process is possible with a variety of images From Inkscape open the file by selecting File gt Open from the top menu and then locate your image and press the Open button logo jpg Inkscape File Edit View Layer Object Path New gt Open Ctrl O Open Recent N Revert Save Ctrl S fe Save As Shift Ctrl 5 Save a Copy Shift Ctri Alt 5 Most major file formats can be opened in Inkscape including jpg gif tif png ico etc Select the image by choosing the selection tool iw LEN 1 E er RA par F y and transform objects F1 T 43 Then click on the image You can tell an image is selected when it shows a dotted border and multiple sets of arrows surrounding its parameter With the image selected select Path gt Trace Bitmap from the top menu Path Text Effects Whiteboard el Objectto Path Shift Ctrl C a StroketoPath Ctri Alt C Trace Bitmap ip Shift Alt B The Trace Bitmap window will appear Trace Bitmap Shift Alt B i x Trace Bitmap Shift Alt 8 H E Mode Options C SIOX foreground selection Single scan creates a path
39. without updates To deactivate the update process redirect the SignBlazer shortcut of either the desktop icon or start menu selection that you use to open the SignBlazer software Right click it and select Properties From the Properties menu change last section of the Target option from sb exe to sbnt exe Press the Apply button then the OK button This will bypass the update process The Blade may be dulled or damaged Replace with a new blade and try again Make sure that the blade can turn freely by attempting to turn it with your fingers while it is set in the Blade Carriage Adjust the blade depth of the Blade Carriage page 16 and Force setting on the cutter page 9 until you are getting solid uniform cuts Follow the instructions on page 16 to set the blade depth and then adjust the Force setting of the cutter until the problem has been corrected If the blade is protruding too far from the Blade Carriage then it can score and cut material during normal operations If this is occurring the blade needs to be adjusted so that it is protruding a minimal distance from the carriage See the instructions on page 16 Check if the power cable is securely connected to the cutter and a grounded power outlet surge protector If the connection is secure and there is still no power than the power cord could be damaged Try another power cord with your cutter or try the power cord from the cutter on a different device to test if
Download Pdf Manuals
Related Search