Home

Product Brochure

1. 6 2 3 Operation with room probe In certain circumstances the stove may need to modulate operation based on the temperature read by the room probe fitted on the stove CE The stove must be setto configuration 2 following the instructions shown in paragraph 6 3 6 2 4 Connection to a storage tank with coil The stove can be used to maintain the temperature inside a storage tank fitted with coil In this case simply disconnect the external temperature probe from the stove and fit it in the probe socket on the storage tank The stove must be set to configuration 3 following the instructions shown in paragraph 6 3 6 2 5 Connection to a storage tank without coil The stove can be used to maintain the temperature inside a storage tank without coil In this case simply disconnect the external temperature probe from the stove and fit it in the probe socket on the storage tank The stove must be set to configuration 4 following the instructions shown in paragraph 6 3 40 136 cod 004772531 07 2013 Palazzetti PN Italy USE AND amp MAINTENANCE PALAZZETTI 6 3 INITIAL CONFIGURATION Depending on the type of installation the best configuration needs to be selected for stove operation Before proceeding power up the stove using the safety switch on the rear Use the arrow buttons to scroll between the icons until reaching the setup menu Yk a Use the arrow buttons 9 0 to go to the setup menu and the
2. Failed ignition error Outlet water temperature too high No pellets Pellet quality Faulty ignition system Burn pot dirty Problems with the heating system Problems with the pump E105 Temperature probe malfunction Faulty return water temperature probe E106 Temperature probe malfunction Faulty buffer tank temperature probe E108 Safety error Door or hopper lid open E108 Thermal safety Problems with the heating system Problems with the pump Problems with overheating in the pellet hopper Pressure error thermal safety Flue gas exhaust system dirty Seal gaskets worn Insufficient combustion air Problems with the heating system Problems with the pump Problems with overheating in the pellet hopper E109 Pressure error Flue gas exhaust system dirty Seal gaskets worn Insufficient combustion air E110 Temperature probe malfunction Faulty outlet water temperature probe Faulty air temperature probe E111 Flue gas temperature probe malfunction Faulty flue gas temperature probe A001 Low pellet level icon flashing Pellets running out M A002 Scheduled maintenance warning icons flashing The stove periodically requires maintenance to be performed by a qualified technician AFA SI A007 Pressure sensor malfunction icon flashing Pressure sensor or board fault Clean sto
3. the setup menu and then press b Use the button to select the password 7 and then press to confirm c Select submenu B and press to confirm d The value will flash change it using the and buttons 0 40 C e Press the button to confirm the set value 10 9 INTEGRATED PRODUCTION OF SANITARY HOT WATER Only in models equipped with an hydraulic unit for the production of sanitary hot water it is possible to produce into the boiler also sanitary hot water in addition to hot water for heating systems This production can take place only if the boiler is operating If the boiler is switched off sanitary hot water cannot be produced cod 004772531 07 2013 Palazzetti PN Italy 51 136 PALAZZETTI 11 ALARM MANAGEMENT USE AND amp MAINTENANCE Ifa malfunction occurs the following procedure is activated 1 2 3 audible alarm beep one of the following system LEDs come on A if the problem concerns an error the stove will switch off Pressing and holding the cancel button shows the error code on the display ERROR WARNING CODE DESCRIPTION Faulty control panel POSSIBLE CAUSES Control panel fault Remote control signal communication error Control panel fault Communication error Connection cable between board and control panel interrupted or detached If this appears when changing configuration ignore the error NNN
4. er CONFIGURAZIONE 4 CONFIGURATION 4 KONFIGURATION 4 CONFIGURATION 4 CONFIGURACI N 4 oad 8 oreet Komponenten enthalten in den Ofen Composants prevus dans le po le Komponenten enthalten in den Ofen Composants prevus dans le po le Piezas incluidas en el kit estufa Piezas incluidas en el kit estufa Components included in the stove Componenti compresi nella stufa Components included in the stove Componenti compresi nella stufa 135 136 cod 004772531 07 2013 Palazzetti PN Italy PALAZZETTI IL CALORE CHE PIACE ALLA NATURA Palazzetti Lelio s p a Via Roveredo 103 cap 33080 Porcia PN ITALY Internet www palazzetti it Per maggiori informazioni tecniche di installazione o di funzionamento operativo il SERVIZIO DI CONSULENZA TECNICA POST VENDITA 0434 591121 l elenco completo dei centri di assistenza tecnica CAT lo trovi su www palazzetti it La Ditta Palazzetti non si assume alcuna responsabilit per eventuali errori del presente opuscolo e si ritiene libera di variare senza preavviso le caratteristiche dei propri prodotti Palazzetti accepts no liability for any mistakes in this handbook and is free to modify the features of its products without prior notice Die Firma Palazzetti bernimmt f r eventuelle Fehler in diesem Heft keine Verantwortung und beh lt sich das Recht vor die Eigenschaften ihrer Produk
5. modifications and repairs on the stove that are not authorised by the manufacturer Use of spare parts that are not original or not specific for the model of stove lack of maintenance exceptional events G 1 10 INTENDED USERS A The user of the stove must be a responsible adult with sufficient technical knowledge to carry out routine maintenance on the parts of the stove Make sure children do not play close to the stove while it s operating cod 004772531 07 2013 Palazzetti PN Italy PALAZZETTI 1 11 TECHNICAL SERVICE PALAZZETTI has an extensive network of service centres staffed by specialists trained directly by the company Please contact our head office or sales network for details of your nearest authorised service centre The company forum http forum palazzetti it offers access to a vast amount of information and allows users to exchange ideas opinions and suggestions 1 12 SPARE PARTS Only use original spare parts Do not wait for components to become worn out before replacing them Replace a worn component before it malfunctions helps prevent accidents due to sudden breakages which may cause serious harm to people and things Perform the periodical maintenance checks as described in the chapter on Maintenance 1 13 IDENTIFICATION LABEL The serial number plate on the stove shows all the typical product data including the manufacturer s details the serial num
6. F Directive 1999 5 EC Radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity UNI 14785 2006 Residential space heating appliances fired by wood pellets Requirements and test methods PRODUCT WARRANTY In order to make use of the product warranty pursuant to Directive 1999 44 EC users must fully comply with the instructions specified in this manual and specifically always use the stove within its operating limits always carry out regular and thorough maintenance allow the stove to be used by people of proven ability attitude and suitably trained for the purpose use original spare parts made specifically for the model of stove in question In addition the following must be provided tax receipt showing the purchase date certificate of conformity of installation issued by the installer Failure to follow the instructions provided in this manual will render the warranty void MANUFACTURER S LIABILITY By providing this manual PALAZZETTI declines all liability both civil and criminal direct or indirect deriving from installation not in compliance with the standards in force in the country concerned and with safety directives partial or total failure to follow the instructions provided in this manual installation by unqualified and untrained personnel e Use in compliance with safety directives
7. 1 2 Description of the menus ICON FUNCTION DESCRIPTION VALUES Power Stove output setting 1 5 Fan This parameter is not enabled on water heating models Displays the room temperature reading and is used to set the desired Temperature 6 C 51 temperature Displays the operating autonomy and resets the value when filling the _ erse Fuel pellet hopper FULL 3 or deactivates the warning OFF 3 FULL OFF 9 Timer Enables or disables the timer When enabled the icon will be ON OFF displayed steady not flashing ICON FUNCTION SUBMENU DESCRIPTION VALUES 1 Weekly timer I the programs max 3 to the different days of the d1 d7 Programs Program setting menu P1 P6 3 Time date Time and date setting Displays the number of hours remaining until recommended 47 Hours remaining maintenance When is displayed the remaining time exceeds 999 hours t5 SIR Displays the current software version information rg Water It allows to set the desired temperature for the water supply 60 80 C temperature only in configuration 2 si Enables or disables Eco Mode in which the stove 13 Eco function automatically switches off and on based on room temperature OFF Eco 3 Setup only in configuration 2 Is the number of degrees centigrade below the switch 05 5 0 C 8 Restart delta off temperature at which the s
8. FUEL SPECIFICATIONS 35 3 2 STORING THE PELLETS 35 4 HANDLING AND TRANSPORT 35 AVAILABLE CONFIGURATIONS 134 4 1 REMOVING THE STOVE FROM THE PALLET 35 5 INSTALLATION SITE PREPARATION 36 5 1 GENERAL INFORMATION 36 5 2 SAFETY PRECAUTIONS 36 53 STOVE INSTALLATION SITE 36 54 COMBUSTION AIR 37 55 FLUE GAS EXHAUST 38 6 INSTALLATION 40 6 1 LEVELLING THE STOVE 40 62 SYSTEM CONNECTIONS 40 6 3 INITIAL CONFIGURATION 41 7 STOVE DESCRIPTION 43 7 1 CONTROL PANEL 43 7 2 USING THE CONTROL PANEL 44 7 3 OPERATING PARAMETERS 45 8 PRELIMINARY OPERATIONS 46 8 1 LOADING THE PELLETS 46 82 POWER SUPPLY 46 83 INITIAL SETTINGS 46 9 STOVE OPERATION 48 9 1 STARTING THE STOVE 48 9 2 MODIFYING THE PARAMETERS 48 9 3 SWITCHING OFF 48 94 OPERATION WITH ROOM THERMOSTAT 48 95 OPERATION WITH ROOM PROBE ON THE BOILER48 9 6 OPERATION IN COMBINATION WITH A STORAGE TANK 48 cod 004772531 07 2013 Palazzetti PN Italy 31 136 PALAZZETTI 1 1 1 1 2 1 3 INTRODUCTION PALAZZETTI heating appliances are built and tested in accordance with the safety requirements specified by the relevant European directives This manual is intended for owners installers users and maintenance personnel of the PALAZZETTI stoves and is an integral part of the product If there are any doubts regarding the contents of this manual or for any other explanations please contact the manufacturer or an authorised service centre quoting the paragraph num
9. a few seconds the flame icon will switch off To start the stove again it s recommended to wait for the stove to cool down completely The stove should only be switched off following the procedure described above Never switch the stove off by unplugging it from the power supply OPERATION WITH ROOM THERMOSTAT When the stove is controlled by an external thermostat or timer thermostat the installer must have set configuration 1 In this configuration the stove switches off when reaching the external thermostat setting or alternatively modulates output that is the stove attempts to maintain the desired temperature while minimising fuel consumption when reaching the set water temperature The stove switches on again automatically when the temperature falls below the value set on the external thermostat circuit closed On first ignition or ifthe stove has been switched off manually button the stove needs to be started directly from the control panel The stove will go off automatically even in the case the water temperature keeps growing notwithstanding the modulation mode In this case the stove will ignite only if the difference between the selected and actual temperature is over 20 C Therefore if you choose this configuration we suggest that you select a high water temperature e g 70 C OPERATION WITH ROOM PROBE ON THE BOILER The boiler can be switched on off manually or in programmed mode In this type of config
10. a fit mental physical state for working and make sure that personal protective equipment is in perfectly working order C always wear safety gloves D always wear safety shoes always use electrically insulated tools F make sure that the area being used for assembly and dismantling is clear of any obstacles 36 136 INSTALLATION 5 3 STOVE INSTALLATION SITE The enclosed Product technical details show the minimum clearances from combustible materials and objects expressed in centimetres that must be observed when positioning the stove for non flammable walls objects these clearances can be halved Protect all structures that may catch fire if exposed to excessive heat Floors made from flammable materials such as wood parquet linoleum laminates or carpets must be protected by a suitably sized fireproof base underneath stove Such base may be made from steel slate glass or stone and must cover the floor in the part underneath the stove and the flue attachment and must extend at least 50 cm at the front The manufacturer declines all liability for any alterations to the characteristics of the material making up the floor underneath the protective base Any elements made from wood e g beams or other combustible material located near the stove should be protected with fireproof material Flammable walls or elements must be kept at least 150 cm away from the stove Leave enough clearance for maintenanc
11. a place that s dry and not too cold suggested to keep some sacks of pellets in the same room where the stove is installed or an adjacent room as long as the temperature and humidity are acceptable Damp and or cold pellets 5 C reduce the fuel heat value and mean the burn pot unburned material and firebox will need to be cleaned more frequently Pay special care when storing and handling the sacks of pellets Make sure these are not crushed to prevent the pellets from becoming sawdust Sawdust introduced into the hopper may block the pellet feed system Use of poor quality pellets may affect normal pellet stove operation and render the warranty void The features of the pellets must comply with the requirements of EN 14961 2 cod 004772531 07 2013 Palazzetti PN Italy 4 4 1 PALAZZETTI Fig 3 1 HANDLING AND TRANSPORT The stove is delivered complete with all parts included Beware of the tendency of the stove to tip over The stove s centre of gravity is towards the front of the appliance Always keep this in mind when moving the stove on the transport pallet When lifting avoid jolts or sudden movements Make sure that the forklift capacity exceeds the weight of the stove being lifted The operator of the forklift or other hoisting equipment is responsible for lifting the loads Prevent children from playing with the packaging components e g film and polystyrene Danger of suffocatio
12. and close the ash bin Close the doors Fig 12 3 Fig 12 4 cod 004772531 07 2013 Palazzetti PN Italy 53 136 PALAZZETTI USE AND amp MAINTENANCE 12 2 4 Cleaning the flue gas compartment o The flue gas compartment should be cleaned fortnightly or whenever necessary Open the door to the flue gas compartment located under the ash bin Fig 12 5 Only for models equipped with turbolators Take out the lever for moving the turbulators and removing the soot Fig 12 6 nsertthis into the special notch and move it up and down to remove the soot deposits from the tubes Fig 12 7 Remove the lever and put it back in its original place Use a special ash vacuum cleaner to vacuum up the residues on the flue gas manifold Carefully close the compartment door again An accurate clearing of heat exchanger smoke ducts has to be done at least one time before the heating season from authorized service a a NS N Fig 12 5 Fig 12 6 12 2 5 Cleaning the glass where foreseen 12 2 6 Cleaning the flue 12 2 7 Cleaning the outside of the stove This is done using a damp cloth or moistened paper passed through the ash Rub until the glass is clean Detergents suitable for cleaning kitchen ovens can also be used Never clean the glass while the stove is operating and never use abrasive sponges Do not wet the door gasket as this may be damaged x B A This should b
13. this manual refers to RESPONSIBILITY FOR INSTALLATION PALAZZETTI accepts no responsibility for the work carried out to install the stove such responsibility lies with the installer who is required to carry out checks on the flue and air intake and ensure installation is completed correctly Furthermore all safety standards required by relevant legislation in force in the country where the stove is installed must be complied with The stove must only be used in compliance with the instructions provided in this manual as well as with all safety standards required by relevantlegislation in force in the country where the stove is installed MAIN REFERENCE STANDARDS A Directive 2006 95 EC Electrical equipment designed for use within certain voltage limits B Directive 2004 108 EC Approximation of the laws of the Member States relating to electromagnetic compatibility C Directive 89 391 EEC Introduction of measures to encourage improvements in the safety and health of workers at work D Directive 89 106 EEC Approximation of the laws regulations and administrative provisions of the Member States relating to construction products cod 004772531 07 2013 Palazzetti PN Italy 1 8 1 9 INTRODUCTION E Directive 85 374 EEC Approximation of the laws regulations and administrative provisions of the Member States concerning liability for defective products
14. value will flash change it using the buttons OFF 3 cO C e Press to confirm the settings Configuration 3 and 4 To set the frost protection temperature a Use the arrow buttons lt 0 to go to the setup menu f and then press b Use the button to select the password 7 and then press to confirm c Select submenu 3 and confirm by pressing d The value will flash change it using the buttons OFF 3 50 C e Press to confirm the settings Setting the value to OFF in step d disables the function 10 8 RESTART DELTA FUNCTION Restart delta configurations 2 3 and 4 is the number of degrees centigrade below the switch off temperature at which the stove switches on again automatically For example if the stove is set to switch off at 20 C Eco Mode active and Restart delta is set to 4 C the stove will switch on again when the temperature measured is less than or equal to 16 C Configuration 2 To set the restart delta value a Use the arrow buttons 4 D to go to the setup menu 3 and then press b Use the button to select the password 7 and then press to confirm c Select submenu B and press to confirm d The value will flash change it using the and buttons 0 5 5 0 C e Press the button to confirm the set value Configuration 3 and 4 To set the restart delta value a Use the arrow buttons C to
15. 531 07 2013 Palazzetti PN Italy USE AND amp MAINTENANCE PALAZZETTI 7 STOVE DESCRIPTION Before reading this booklet check the description of the stove provided in the Product Booklet enclosed 7 1 CONTROL PANEL The control panel consists of A atop part with status LEDs and backlit icons that identify each function LED display ON button D Cancel and display error button two arrow buttons to scroll between the various functions F twobuttons Jand to access the submenus and set the operating parameters G an enter button o confirm the parameter or q the settings db e C8 Allthe buttons are capacitive therefore the functions b d PALAZZETTI are activated without needing to press hard on the buttons rather by just touching the surface Fig 7 1 7 1 1 STATUS LEDS ICON WARNING DESCRIPTION Pellets running out Indicates that the pellet hopper needs to be refilled S Maintenance Indicates the need to perform maintenance VA Service ndicates an error Remote control receiver OPTIONAL ris Timer active Indicates whether the timer function is active Status LED near the 8 LED on steady soye on and Operating button LED flashing stove in the ignition stage or in standby LED off stove off cod 004772531 07 2013 Palazzetti PN Italy 43 136 PALAZZETTI USE AND amp MAINTENANCE 7
16. AILABLE 10 1 TIMER FUNCTION It s possible to set enable and assign to the various days of the week customised programs for automatically switching the stove on and off Up to six customised programs can be set For each program the following can be set on time off time and desired temperature Up to three programs can be assigned for each day of the week The days of the week are identified by numbers Monday d1 Tuesday d2 Sunday d7 10 1 1 Setting the programs a Use the arrow buttons to go to the setup menu and then press b Use the button to select the password 7 and then press to confirm c Select submenu 2 and confirm by pressing d Use the buttons to scroll the programs P1 P6 e The on hours value will flash set the value using the buttons and press p f The minutes value will flash set the value using the buttons and press g The off hours value will flash set the value using the buttons and press h minutes value will flash set the value using the buttons and press i The desired temperature value will flash set the value using the buttons and press D j Press to confirm the settings 10 1 2 Assigning the programs to specific days This function can be used to assign up to three different programs to a certain day a Use the arrow buttons to go to the setup menu f and then p
17. ANCE Naa HHH HH HH eee 53 ASSISTERE 13 DECOMMISSIONING AND DISPOSAL rrecreii 55 St ELECTRICIAN w INTRODUCTION c e 32 Y 2 SAFETY WARNINGS scia 34 A 4 HANDLING AND TRANSPORT I III HK AHA RA 35 13 DECOMMISSIONING AND DISPOSALL I a 55 SHUNTER TRANSPORTER 30 136 cod 004772531 07 2013 Palazzetti PN Italy PALAZZETTI INDEX 1 INTRODUCTION 32 10 FUNCTIONS AVAILABLE 49 11 SYMBOLS 32 10 1 TIMER FUNCTION 49 12 INTENDED USE 32 10 2 ECO MODE SAVING FUNCTION 50 13 PURPOSE AND CONTENTS OF THIS MANUAL 32 10 3 AUTONOMY FUNCTION 50 14 HOW TO KEEP THIS MANUAL 32 104 REFILLFUNCTION 50 15 UPDATES TO THE MANUAL 32 10 5 RESTARTING AFTER A POWER FAILURE 50 16 GENERAL INFORMATION 32 106 LOCK KEYPAD FUNCTION 50 3 17 MAIN REFERENCE STANDARDS 32 107 FROST PROTECTION FUNCTION 51 o 1 8 PRODUCT WARRANTY 33 10 8 RESTART DELTA FUNCTION 51 Em 19 MANUFACTURER S LIABILITY 33 10 9 INTEGRATED PRODUCTION OF SANITARY HOT o 1 10 INTENDED USERS 33 WATER 51 Es 1 11 TECHNICAL SERVICE 33 1 12 SPARE PARTS 33 1 13 IDENTIFICATION LABEL 33 11 ALARM MANAGEMENT 52 1 14 DELIVERY OF THE STOVE 33 12 MAINTENANCE 53 2 SAFETY WARNINGS 34 124 SAFETY PRECAUTIONS 53 24 INSTALLATION WARNINGS 34 122 ROUTINE USER MAINTENANCE 53 22 MAINTENANCE WARNINGS 34 12 3 SPECIAL MAINTENANCE 55 23 WARNINGS FOR THE USER 34 13 DECOMMISSIONING AND DISPOSAL 55 FUEL SPECIFICATIONS 35 3 1
18. IX AFIN DE VOUS PERMETTRE DE PROFITER AU MIEUX DE VOTRE NOUVEAU POELE NOUS VOUS INVITONS A SUIVRE ATTENTIVEMENT LES INSTRUCTIONS REPORTEES DANS CETTE NOTICE EsTIMADO CLIENTE ES DESEAMOS AGRADECERLE POR LA PREFERENCIA QUE NOS HA OTORGADO ADQUIRIENDO NUESTRO PRODUCTO Y LO FELICITAMOS POR SU ELECCI N PARA EL MEJOR USO DE SU NUEVA ESTUFA LO INVITAMOS A LEER CON ATENCI N CUANTO SE DESCRIBE EN EL PRESENTE MANUAL cod 004772531 07 2013 Palazzetti PN Italy 3 136 PALAZZETTI SUMMARY FOR SKILLS 1 INTRODUCTION I K 32 w 2 SAFETY WARNINGS I I I AH AK Hak r k HH KK HHR ARA 34 3 FUEL SPECIFICATIONS iniit msi Ee tna mta ate oui i Pe Rc 35 8 PRELIMINARY OPERATIONS I I I tnter ei 46 mE 9 STOVE OPERATION iii 48 10 FUNCTIONS AVAILABLE I I tenet tate III aaa 49 11 ALARM MANAGEMENTT II I aaa 52 12 MAINTENANCE iii 53 13 DECOMMISSIONING AND DISPOSAL s csescereceeiineeninee 55 INTRODUCTION rain 32 Ast 2 SAFETY WARNINGS curl 34 4 HANDLING AND TRANSPORT 35 5 INSTALLATION SITE PREPARATION sese tnnt IIIa nani 36 EINSTALIATIO Nn 40 w 7 STOVE DESCRIPTION c scsssssscsesssessessssssesssessesesessesescsesseseseesesesesstusecacsacaesesneaeseansesses 43 8 PRELIMINARY OPERATIONS 46 4 12 MAINTEN
19. LETS The first operation to be performed before starting the appliance is to fill the hopper with fuel pellets The pellets are loaded into in the hopper using a scoop Do not empty the sack directly into the hopper so as to avoid loading sawdust or other foreign bodies that may affect proper stove operation and avoid spilling pellets outside of the hopper Make sure the hopper lid is well closed again after having loaded the pellets A safety switch just for the models that are equipped with it makes sure thatthe pellet tank lid has been closed properly IS in fig 8 1 and triggers a stove alarm in case the pellet tank lid stays open for more than one minute while the stove is still working Fig 1 At this point to take advantage of the Autonomy function use the arrow buttons to move to the combustible icon i and confirm by pressing Select Full by pressing and press button to confirm In order to disable this function select Off instead of Full POWER SUPPLY Plug the stove into the mains power supply move the power switch at the rear of the stove to position P Fig 8 2 If the connections are correct the stove will emit a series of intermittent beeps the display will come on If not using the appliance for an extended period the switch at the rear of the stove should be moved to position INITIAL SETTINGS The language current date and
20. PALAZZETTI IL CALORE CHE PIACE ALLA NATURA MANUALE DI INSTALLAZIONE USO E MANUTENZIONE INSTALLATION USER AND MAINTENANCE MANUAL INSTALLATIONS BEDIENUNGS UND WARTUNGSANLEITUNGEN NOTICE D INSTALLATION MANUAL DE INSTALACI N USO Y MANTENIMIENTO STUFE A PELLET ECOFIRE IDRO ECOFIRE IDRO PELLET STOVES IDRO PELLET FEN ECOFIRE POELES A PELLETS ECOFIRE IDRO ESTUFAS DE PELLETS ECOFIRE IDRO EASY TOUCH PALAZZETTI GENTILE CLIENTE t IT DESIDERIAMO INNANZITUTTO RINGRAZIARLA PER LA PREFERENZA CHE HA VOLUTO ACCORDARCI ACQUISTANDO IL NOSTRO PRODOTTO CONGRATULIAMO CON LEI PER LA SCELTA PER CONSENTIRLE DI UTILIZZARE AL MEGLIO LA SUA NUOVA STUFA LA INVITIAMO A SEGUIRE ATTENTAMENTE QUANTO DESCRITTO NEL PRESENTE MANUALE DEAR CUSTOMER WE D LIKE TO THANK YOU FOR HAVING PURCHASED ONE OF OUR PRODUCTS AND CONGRATULATE YOU ON YOUR CHOICE To MAKE SURE YOU GET THE MOST OUT OF YOUR NEW STOVE PLEASE CAREFULLY FOLLOW THE INSTRUCTIONS PROVIDED IN THIS MANUAL SEHR GEEHRTER KUNDE DE ZUALLERERST M CHTEN WIR IHNEN F R DEN UNS GEW HRTEN VORZUG DANKEN UND IHNEN ZUR WAHL GRATULIEREN DAMIT SIE IHREN NEUEN HEIZOFEN SO GUT WIE M GLICH BENUTZEN KONNEN BITTEN WIR SIE DIE IN DIESER BEDIENUNGS UND WARTUNGSANLEITUNG ENTHALTENEN ANGABEN GENAU ZU BEFOLGEN CHER CLIENT F Nous SOUHAITONS AVANT TOUT VOUS REMERCIER DE LA PREFERENCE QUE VOUS NOUS AVEZ ACCORDEE EN ACHETANT NOTRE PRODUIT ET VOUS FELICITIONS POUR VOTRE CHO
21. ZETTI 7 3 OPERATING PARAMETERS Stove operation is determined by the Power level and Temperature parameters set by the user 7 3 1 setting the power level The power level defines the amount of heat produced by the stove and consequently directly affects fuel consumption To change the power level use the buttons to go to the power menu P a Use the buttons to scroll the submenu b Select submenu 1 and confirm by pressing The power level value will flash the value using the buttons 1 minimum 5 maximum d Press to confirm the settings HSITSNA 7 3 2 Setting the temperature Different temperature values can be set depending on the boiler s configuration a Use the buttons to go to the temperature menu and press b The current value will flash change it using the buttons c Press to confirm the settings Water temperature configurations 1 only setting this value changes the desired hot water outlet temperature Room temperature configuration 2 only setting this value defines the desired room temperature read directly by a probe fitted on the boiler Storage temperature configurations 3 and 4 only identifies the minimum desired temperature inside the storage tank 45 136 cod 004772531 07 2013 Palazzetti PN Italy PALAZZETTI ZE MAINTENANCE 8 8 1 8 2 8 3 8 3 1 PRELIMINARY gt OPERATIONS LOADING THE PEL
22. and the real one is higher than 20 C In this configuration it is therefore recommended to regulate a high water temperature ex 70 C CONFIGURATION 2 Set this configuration to switch the stove on or off manually or by timer when the stove is connected directly to the central heating radiators The stove will modulate output according to the room temperature read by the probe on the stove The Eco mode function can be usedto have the stove switch off oron based on the set room temperature The frost protection function can also be set in this configuration CONFIGURATION 3 Set this configuration when wanting to connect the stove to a storage tank with coil The stove will be controlled switch on and off based on the temperature read by the probe in the storage tank The frost protection function can also be set in this configuration CONFIGURATION 4 Set this configuration when wanting to connect the stove to a storage tank without coil The stove will switch on based on the temperature read by the probe in the storage tank and will switch off based on the stove return temperature The frost protection function can also be set in this configuration Some typical installation diagrams are shown on the last few pages of the booklet cod 004772531 07 2013 Palazzetti PN Italy 41 136 PALAZZETTI USE AND amp MAINTENANCE USE AND amp MAINTENANCE a X P r tTT__rrrerr_ si 42 136 cod 004772
23. ber and C markings 1 14 DELIVERY OF THE STOVE The stove is delivered packaged in a cardboard box or shrink wrap and secured to a wooden pallet for handling by forklift and or other equipment The following material is provided inside the stove installation user and maintenance manual product booklet pertaining to the specific model remote control only on models where featured tool for opening of the firebox door only on models where featured 33 136 EJ ESI ES SF PALAZZETTI 2 2 1 N N Di N DI SAFETY WARNINGS INSTALLATION WARNINGS Comply with the requirements specified in this manual The stove assembly and dismantling instructions are reserved exclusively for specialist technicians Users should always contact our service centre to request work to be performed by qualified technicians Before having work performed by other technical personnel verify their effective technical competence Responsibility for work carried out in the place where the stove is installed lies with the user the user is also responsible for making sure the installation checks are completed The user must abide by all local national and European safety requirements The appliance must be installed on floors with a suitable load bearing capacity Make sure that the flue and air intake duct arrangements correspond to the type of installation Do not make any electrical
24. ber in question No printing translation and reproduction of this manual in part or whole is allowed without the permission of PALAZZETTI The technical information illustrations and specifications included in this manual may not be disclosed Do not operate the appliance if any of the instructions provided in the manual are not understood if there are any doubts always contact specialist PALAZZETTI personnel for explanations PALAZZETTI reserves the right to modify the technical and or functional specifications of the stove at any time without prior notice SYMBOLS The most important points in this manual are highlighted by the following symbols INSTRUCTION Instructions concerning correct stove operation and the responsibilities of operators IMPORTANT This denotes very important information DANGER This specifies the behaviour required to prevent accidents or damage to materials INTENDED USE PALAZZETTI appliances are stoves designed for heating the home to be installed indoors with automatic operation exclusively on wood pellets The stove can only operate with the firebox door closed Never open the door when the stove is operating The appliance is not intended for use by people including children with limited physical sensorial or mental abilities or without sufficient experience or knowledge unless they are supervised or instructed on the use of the appliance by a person responsible for thei
25. connections using temporary or uninsulated cables Make sure the electrical system is earthed correctly Before starting to assemble or dismantle the stove the installer must heed the safety precautions required by law specifically A donot work in adverse conditions B always be ina fit mental physical state for working and make sure that personal protective equipment is in perfect working order always wear safety gloves always wear safety shoes always use electrically insulated tools make sure that the area being used for assembly and dismantling is clear of any obstacles MAINTENANCE WARNINGS Comply with the requirements specified in this manual Use always personal protective equipment and other means of protection Before starting any maintenance work make sure that the stove if it had been operating has cooled down f even just one of the safety devices is not calibrated or not working the stove must be considered out of service Disconnect power before working on electrical or electronic parts and connectors WARNINGS FOR THE USER Prepare the stove installation site in accordance with local national and European regulations As the stove is a heating appliance it has very hot outside surfaces For this reason maximum care must be paid during operation specifically do not touch or get too close to the glass door to avoid getting burned do not touch the flue do
26. consuming the least amount of fuel possible The Eco Mode function is only available in configuration 2 To enable disable the function a Use the arrow buttons YC te go to the setup menu and then press b Use the button to select the password 7 and then press to confirm c Select submenu 1 and confirm by pressing d Set one of the following values using the buttons ECO Eco Mode function enabled OFF Eco Mode function disabled e Press to confirm the settings AUTONOMY FUNCTION This function is used to display the number of hours of operating autonomy remaining before having to refill with pellets Use the arrow buttons to move to the lg symbol and display the estimated operating hours before having to refill with pellets The autonomy is calculated according to the operating parameters set at that moment on the stove The estimated values are quite reliable as long FULL is selected and confirmed whenever refilling the stove completely Lo indicates the reserve fuel level 10 4 REFILL FUNCTION 10 5 10 6 This function is used to tell the stove that the hopper is being filled with pellets In this way the stove can estimate based on the operating parameters how many hours of autonomy remain before having to fill the hopper with pellets again After having completely filled the pellet hopper a Use the arrow buttons 3 to move to the fuel
27. e performed at least twice a year at the start of and half way through winter and in any case whenever necessary Fig 12 9 If there are horizontal sections check for and remove any accumulated ash and soot before these block the flow of flue gas Fig 12 8 If not cleaned correctly the stove may not operate a properly with problems including poor combustion blackening of the glass blockage of the burn pot by ash and pellets accumulated ash and excessive fouling of the i heat exchanger with a consequent decline in pi 2 efficiency rm The outside of the stove must only be cleaned using a dry non abrasive cloth Do not use detergents and never clean when the stove is hot E Fig 12 9 54 136 cod 004772531 07 2013 Palazzetti PN Italy PALAZZETTI 12 3 SPECIAL MAINTENANCE The pellet stove is a solid fuel fired heater and as such requires annual maintenance to be performed by a Palazzetti Authorised Service Centre once a year preferably at the start of the season The purpose of such maintenance is to ensure all the components are in perfect working order If the control panel shows the SS symbols together immediately contact the Service Centre to have special maintenance performed on the stove This warning can be reset temporarily by pressing the button and then starting the stove again Mu The warning will be
28. e work Make sure the minimum distance from flammable materials x is observed as shown on the pipes used to make up the flue or chimney Fig 5 2 Pi Combustible wall Pp Floor protection Pi 150 cm Fig 5 2 cod 004772531 07 2013 Palazzetti PN Italy dv Sa PALAZZETTI 5 4 COMBUSTION AIR During operation the stove takes in certain amount sa of air from the room where it s installed except for TT the Ermetica series products that can take in air l directly from the outside this air must be replaced mm through an opening to the outside from the room LT Fig 5 3 PA Fresh air vent If wall behind of the stove is outside wall mm n make an opening for drawing in combustion air LL PA Qo around 20 30 cm above the floor observing the sil dimensions shown on the product data sheet O the end of this booklet BE A permanent non closable vent cover must be placed on the outside of the opening in especially windy areas or places exposed to bad weather install rain and wind protection elements Make sure that the air vent is located in such a way that it can t be accidentally obstructed If it s not possible to make a fresh air opening in the wall behind the stove not a perimeter wall an opening must be made on the wall in the room where the stove is installed that faces the o
29. emains on the last operation set by the user 1 All operating parameters are displayed cyclically 2 The room or water probe temperature is shown based on the type of configuration The current time is shown The operating autonomy in hours before having to refill the hopper is shown If the function filling has been activated e Press to confirm the settings 4 8 3 3 Setting the display brightnes Display brightness when in standby mode can be set a Use the arrow buttons lt to go to the setup menu f and then press b Use the button to select the password 7 and then press to confirm c Use the button to scroll to and select submenu L 1 and press to confirm d Set the desired brightness OFF 5 using the buttons and press to confirm 8 3 4 Setting the volume The volume of the buzzer can be set based on requirements a Use the arrow buttons lt to go to the setup menu f and then press b Use the button to select the password 7 and then press to confirm c Use the button to scroll to and select submenu 13 and press to confirm d Set the desired volume OFF 1 to 5 using the buttons and press to confirm 8 3 5 Setting the type of pellets The type of pellets used can be set a Use the arrow buttons q to go to the setup menu and then press b Use the button to select t
30. he password 7 and then press to confirm c Use the button to scroll to and select submenu 14 and press to confirm d Set one of the following values using the and buttons 1 Small pellets 2 e Medium sized pellets 9 e Large pellets e Press to confirm the settings cod 004772531 07 2013 Palazzetti PN Italy 47 136 PALAZZETTI USE AND amp MAINTENANCE 9 3 9 4 9 5 9 6 STOVE OPERATION STARTING THE STOVE To start the stove hold the button for several seconds The flame icon will start flashing during the ignition stage until remaining on steady when the stove has started Automatic stove ignition the stove comes with an automatic device that starts the pellet stove without using other traditional fire lighters Avoid lighting the flame manually if the stove s automatic ignition system is not working correctly When the stove is started the first time unpleasant odours or smoke may be generated caused by evaporation or drying of certain materials used This phenomenon will gradually disappear The room should be well ventilated when starting the stove the first few times MODIFYING THE PARAMETERS The stove operating parameters can be modified as described in paragraph 7 3 The values set will be retained until next modified even when the stove is switched off or unplugged from the power supply SWITCHING OFF To switch the stove off hold the button for
31. icon press ente b Use the buttons to select FULL and press enter To disable this function select OFF instead of FULL RESTARTING AFTER A POWER FAILURE In the event of power failures the stove will switch back on automatically checking the safety conditions when power returns LOCK KEYPAD FUNCTION This function is used to disable the use of the control panel and avoid accidental modifications To enable disable the function a Use the arrow buttons 9 to go to the setup menu and then press b Use the button to select the password 7 and then press to confirm c Select submenu and confirm by pressing d Use the buttons to set one of the following values BFF Lock keypad disabled Lo Only the on off button is enabled HI Lock keypad enabled e Press to confirm the settings 50 136 cod 004772531 07 2013 Palazzetti PN Italy USE AND amp MAINTENANCE PALAZZET TI 10 7 FROST PROTECTION FUNCTION In configurations 2 3 and 4 a minimum temperature can be set below which the boiler will switch on outside of the set time bands Configuration 2 To set the frost protection temperature a Use the arrow buttons 3 D to go to the setup menu f and then press b Use the button to select the password 7 and then press to confirm c Select submenu 9 and confirm by pressing d The
32. irs have been completed before operating the stove again restore all protection features and reactivate all safety devices CE A suitable ash vacuum cleaner canister makes it simpler to clean the ash EJ ESI E 12 2 ROUTINE USER MAINTENANCE 12 2 1 Cleaning the inside of the firebox The stove requires simple yet frequent and thorough cleaning in order to guarantee efficient and correct operation at all times AN Clean the stove only when it s off and has cooled down Use the handle or lever according to the model of stove to open the firebox door C amp 7 Some models of stove come with a separate handle for opening the door Take the handle from the ash bin housing place it in the holes on the door hinge and lever the mechanism to open the door Fig 12 1 Fig 12 1 12 2 2 Daily cleaning Remove the ash that has accumulated inside the firebox Fig 12 2 This has the purpose of ensuring free flow of combustion air through the holes in the BURN POT Lift remove the burn pot and clean the surfaces and the compartments inside the burn pot Fig 12 3 Fig 12 2 12 2 3 Cleaning the ash bin The ash bin should be cleaned every week or whenever necessary To access the ash bin open the ash bin door where foreseen and remove the bin Fig 12 4 using the tool provided Empty the bin into a special metal ash collection container Vacuum any residual ash from the compartment that houses the ash bin Reposition
33. n REMOVING THE STOVE FROM THE PALLET To remove the stove from the transport pallet follow the instructions shown in the Product Booklet enclosed 35 136 m 2 o I PALAZZETTI 5 5 1 5 2 INSTALLATION SITE PREPARATION GENERAL INFORMATION The following paragraphs provide instructions that must be complied with in order to ensure maximum efficiency of the product purchased The following instructions are however subordinate to compliance with any national regional and local laws and standards in force in the country where the product is installed SAFETY PRECAUTIONS Responsibility for work carried out in the place where the stove is installed lies with the user the user is also responsible for making sure the installation checks are completed The user must abide by all local national and European safety requirements The appliance must be installed on floors with a suitable load bearing capacity The stove assembly and dismantling instructions are reserved exclusively for specialist technicians Users should always contact our service centre to request work to be performed by qualified technicians Before having work performed by other technical personnel verify their effective technical competence Before starting to assemble or dismantle the stove the installer must heed the safety precautions required by law specifically A do not work in adverse conditions B always be in
34. n press b Use the button to select the password 7 and then press to confirm c Use the buttons to scroll to and select submenu 30J will flash on the display d Press and enter the value 54 using the buttons e Press to confirm f The current configuration will be displayed g To change the configuration press J and enter the value of the new configuration using the buttons h Press to confirm e After having changed the configuration a communication error message may be displayed for a few seconds Ignore this and switch the stove off using the safety switch on the rear wait a few seconds and switch it back on FOUR DIFFERENT CONFIGURATIONS ARE AVAILABLE CONFIGURATION 1 Set this configuration when the stove is controlled by an external thermostat or timer thermostat This configuration can also be used to switch the stove on or off manually or by timer without using an external thermostat but rather leaving the two terminals jumpered as per the factory setting In this configuration the stove switches off when reaching the external thermostat setting or alternatively modulates output to minimise fuel consumption when reaching the set water temperature The stove will turn off also in case the water temperature continues to rise despite the modulation In this case the stove will turn on only if the temperature difference between the value you set up
35. ng the plug supplied The electrical connection plug must be easily accessible when the stove is installed If the power cord is damaged it must be replaced by the technical service or a qualified technician to prevent any kind of risk 6 2 1 1 Earth The system must be earthed and fitted with a residual current circuit breaker in accordance with legislation in force Fig 6 2 The flue must have its own earth connection 6 2 2 Connection to an external timer thermostat The stove can be connected to an external timer thermostat that switches the stove on or off according to the set temperature When the set temperature is reached the thermostat opens the circuit and consequently switches off the stove The external thermostat is connected to the two terminals on the rear of the stove which are jumpered in the factory Disconnect the jumper and connect the two thermostat contacts The stove must be set to configuration 1 following the instructions shown in the paragraph on Initial configuration After first installing the timer thermostat the stove needs to be switched on manually Fig 6 2 while the timer thermostat is in call status This operation is also required in the event of power failures or if the stove is switched off manually To avoid overlapping the working time bands it s recommend to disable set to OFF the stove s timer see par 10 1
36. ng with suitable insulation rock wool vermiculite the flue gas can be discharged directly into the chimney only if the latter has a maximum cross section of 15 x 15 cm or diameter of 15 cm and features an inspection opening For larger chimneys suitably insulated steel pipes need to be inserted on the inside diameter according to the length Fig 5 9 Makes sure connections to brick chimneys are suitably sealed Avoid contact with combustible materials e g wooden beams and in any case insulate these t using fireproof material meues If the flues run through wooden roofs or walls C Seal special certified pass through kits need to be used D Inspection available on the market HSITS9N3 A Chimney pot with wind protection Fig 5 8 B Maximum cross section of 15 x 15 cm or diameter of 15 cm and maximum height of 4 5 e 1 Vermiculite and or rock wool 2 Steel pipes 3 Closure panel Fig 5 9 cr _ 5 cod 004772531 07 2013 Palazzetti PN Italy 39 136 PALAZZETTI rv sed gus _ 6 INSTALLATION al The stove must be installed by qualified personnel in compliance with EN 10683 6 1 LEVELLING THE STOVE The stove must be levelled by adjusting the feet where featured then checked using a spirit level Fig 6 1 A B Spirit level 6 2 SYSTEM CONNECTIONS EMEN 6 2 1 Electrical connection The stove is connected to the electrical system simply usi
37. not perform any type of cleaning 34 136 INTRODUCTION do not remove the ash do not open the glass door do not open the ash bin where featured make sure children keep away from the stove Comply with the requirements specified in this manual Follow the instructions and warnings highlighted on the metal labels affixed to the stove These labels are safety devices therefore they must always be perfectly legible If damaged or illegible they must be replaced contacting the manufacturer for an original spare label Only use fuel compliant with the specifications shown in the corresponding chapter of this manual Strictly follow the routine and special maintenance plan Donotuse the stove without first having performed the daily inspection as specified in the chapter on Maintenance in this manual Donotuse the stove in the event of malfunctions suspected breakage or unusual noises Do not pour or spray water onto the stove when operating or to extinguish the flame in the burn pot Do not switch the stove off by unplugging the power cord Do rest your weight on the open door as this may affect stability e Do not use the stove any way as a support or anchor Donotclean the stove until the structure and ash have completely cooled down Touch the door only when the stove has cooled down Perform all operations without haste in such a way as to en
38. ove must be connected to its own separate flue gas exhaust system capable of ensuring adequate atmospheric dispersion of the combustion by products The components making up the flue gas exhaust system must be suitable for the specific operating conditions and bear the CE mark The flue pipe must have an internal diameter equal to exhaust output of the stove For the flue dimensioning use 0Pa The flues should be suitably insulated e g using rock wool or made using double wall steel pipes except for the initial vertical section inside the room e An initial vertical section measuring a minimum of 1 5 metres is required to ensure correct flue gas exhaust There should be at least three changes in direction along the flue in addition to the flue connection at the rear of the stove using 45 or 90 angle connectors or T connectors Use always a T connector with inspection cap B on all horizontal or vertical changes in flue direction CE necessary to connect a pipe at the bottom of the junction in order to discharge the smoke condensate that could form in the flue gas exhaust The connection must be sealed Fig 5 7b The maximum length of horizontal sections is 2 3 m with an upwards slope of 3 596 Fig 5 7a Anchor the flues to the wall using special collars The flue gas exhaust attachment MUST NOT BE connected to chimney used by other heat generators boilers stoves fi
39. r safety The intended use of the stove described above and the configurations available are the only ones permitted by the manufacturer never use the stove in any way not described in the instructions provided PURPOSEANDCONTENTSOFTHISMANUAL The purpose of this manual is to provide the fundamental and essential rules for correct installation maintenance and use of the product Carefully following these rules will ensure a high level of stove safety and productivity 32 136 INTRODUCTION 1 4 1 5 1 6 1 7 gt lt 7 HOW TO KEEP THIS MANUAL STORAGE AND REFERENCE This manual must be kept with care and must be always available for reference by the user and by assembly and maintenance personnel The installation manual is an integral part of the stove DAMAGE OR Loss If required an additional copy can be ordered from PALAZZETTI SALE OF THE STOVE If the stove is sold the user must also provide the new owner this manual UPDATES TO THE MANUAL This manual represents the state of the art at the time the stove was introduced onto the market GENERAL INFORMATION REQUESTING INFORMATION If information is requested from the manufacturer of the stove always refer to the serial number and other identifying data shown on the product s identification label SPECIAL MAINTENANCE Special maintenance operations must be carried out by qualified personnel who are authorised to work on the model of stove that
40. rature ambiante Sonda temperatura ambiental MC Componenti compresi nella stufa Components included in the stove Komponenten enthalten in den Ofen Composants prevus dans le po le Piezas incluidas en el kit estufa 134 136 cod 004772531 07 2013 Palazzetti PN Italy PALAZZETTI CONFIGURAZIONE 3 CONFIGURATION 3 KONFIGURATION 3 CONFIGURATION 3 CONFIGURACION 3 COLLETTORE PANNELLO SOLARE amp x ped 4 1 Sonde brancher dans le balloni tampon Sonda deposito inercial Sonda puffer Heat Storage probe Puffer Fuehler Heat Storage probe Sonde brancher dans le ballon tampon Sonda deposito inercial Sonda puffer Puffer Fuehler ER 8 oreet
41. replaces etc air exhaust systems range hoods vents etc even if these are ducted Shut off or draught valves must not be used Combustion byproducts must be discharged through the roof If the flue is longer than 5 metres and there is insufficient draught many changes in direction unsuitable discharge terminal etc flue gas exhaust may be less than optimum In these cases the operating parameters will need to be modified flue gas exhaust and pellet load to adapt the stove to the actual characteristics of the flue Contact technical service for this procedure eo yv Fig 5 7a MAX2 3m Fig 5 7b 38 136 cod 004772531 07 2013 Palazzetti PN Italy INSTALLATION 5 5 1 Discharge through roof using a traditional chimney The chimney used to discharge the flue gas must be made in accordance with standards UNI 10683 EN 1856 1 2 EN 1857 EN 1443 EN 13384 1 3 EN 12391 1 both as regards the dimensions and the construction materials used DAMAGED chimneys made from unsuitable material asbestos cement galvanised steel etc with a rough and porous inside surface are prohibited by law and affect proper stove operation The flue gas can be discharged through a traditional chimney Fig 5 8 as long as the following rules are observed check the conditions of the chimney old chimneys should be renovated by introducing steel pipi
42. ress b Use the button to select the password 7 and then press to confirm c Select submenu and confirm by pressing d Use the 9 buttons to choose the day d1 d7 to assign the programs to e Select this using the button f The value of the first program to assign will flash P P6 or OFF to disable g Set the value using the buttons and press h The value of the second program to assign will flash P P6 or OFF to disable i Set the value using the buttons and press j The value of the third program to assign will flash P PB or GFF to disable k Set the value using the buttons and press to confirm the settings 10 1 3 Enabling disabling the timer a Use the arrow buttons 3 C to go to the Timer menu b Select this using the button c Use the buttons to scroll and select to enable the timer or OFF to disable it d Press to confirm the selection When the timer is enabled the ds icon will be on steady indicating that the timer is active cod 004772531 07 2013 Palazzetti PN Italy 49 136 PALAZZETTI USE AND amp MAINTENANCE 10 2 10 3 ECO MODE SAVING FUNCTION Enabling this function means that the stove switches off when reaching the desired room temperature If this function is not enabled the stove modulates operation so as to maintain the desired temperature while
43. shown again until special maintenance is performed by the Authorised Service Centre which will also reset the operating hour counter r INSPECTION AND OR MAINTENANCE PLAN WHENEVER 1MONTH 6 MONTHS 1 YEAR Ash bin Compartment Glass Heat exchanger responsibility of the Authorised Service Centre Fe cene x x j _ gt j rl 1 x j Ignition heater socket gt lt X __ _ x LJ c gj pex o gt 13 DECOMMISSIONING AND DISPOSAL Decommissioning and disposal of the stove are the exclusive responsibility of the owner who must act in accordance with the laws in force in the country where the stove is installed with regards to safety and environmental protection The stove may also be dismantled and disposed of by companies authorised to recover and dispose of the materials in question INSTRUCTION always observe the standards in force in the country where the stove is decommissioned as regards disposal of the materials and the waste disposal report where required IMPORTANT All dismantling operations for decommissioning the stove must be performed when the stove is off and disconnected from the power supply remove all electrical equipment separate the batteries fitted on the electronic boards have the structure of the stove scrapped by an authorised company IMPORTANT Dumping the stove in accessible areas represents a serious ha
44. sure maximum safety event of fire in the chimney switch the stove off using the procedure described in par 9 3 Inthe event of stove malfunctions due to flues with incorrect draught clean the flue according to the procedure described in par 15 4 e The flue must be cleaned as described in paragraph 15 4 Do not touch the painted parts during operation to avoid damaging the paintwork cod 004772531 07 2013 Palazzetti PN Italy INTRODUCTION FUEL SPECIFICATIONS FUEL SPECIFICATIONS Pellets Fig 3 1 are made from various types of mechanically compacted wood in compliance with environmental protection standards Pellets are the only fuel that can be used on this type of stove The efficiency and heat output of the stove may vary in relation to the type and quality of pellets used The pellet stove requires pellets with the following characteristics diameter 6 mm max length 30 mm max moisture content 6 9 The stove has a pellet hopper with the capacity specified in the technical data table in the Product Booklet enclosed The pellet hopper is located at the top of the stove It must always be able to be opened to load the pellets and must remain closed during operation Due to temperature control requirements operation on traditional wood is not possible The stove must not be used as a rubbish incinerator STORING THE PELLETS The pellets must be kept in
45. te ohne Vorbescheid zu andern Palazzetti d cline toute responsabilit en cas d erreurs dans la pr sente documentation et conserve la facult de modifier sans pr avis les caract ristiques de l appareil La empresa Palazzetti no se responsabiliza de los errores eventuales de este manual y tiene el derecho de modificar sin previo aviso las caracter sticas de sus productos Proizvajalec Palazzetti ne prevzema odgovornosti za morebitne napake v tem zvezku in si pridrzuje pravico do vnosa sprememb na svojih izdelkih brez predhodnega obvestila Ufficio libretti Palazzetti cod 004772531 07 2013 Palazzetti PN Italy
46. time need to be set before using the stove Fig 2 Time and Date setting To set the date a Use the p buttons to go to the setup menu and press b Use the button to select the password 7 and then press to confirm c Use the button to scroll to and select submenu 3 and press to confirm d The hour value will flash set the value using the buttons and press D e The minutes value will flash set the value using the buttons and press f The day value will flash set the value using the buttons and press g The month value will flash set the value using the buttons and press h year value will flash set the value using the buttons and press P i The current weekday value will flash Monday 1 Sunday 7 set the value using the buttons j Press to confirm the settings 46 136 cod 004772531 07 2013 Palazzetti PN Italy USE AND amp MAINTENANCE PALAZZET TI 8 3 2 Setting the display mode The data shown on the display when this is in standby mode can be set Use the arrow buttons 3 to go to the setup menu and then press Use the button to select the password 7 and then press to confirm Use the button to scroll to and select submenu ie and press to confirm Set one of the following values using the and buttons a b 9 2 aa DH OFF The display r
47. tove switches on again 0 40 C automatically except in configuration 1 us 9 Frost protection Minimum temperature below which the stove switches on OFF 20 C temperature except in configuration 1 OFF 3 50 t 8 Lock keypad Disables the buttons on the keypad OFF Lo Hi Display brightness Sets display brightness OFF 1 5 Display mode Sets how the data is displayed OFF 1 4 13 Buzzer volume Sets the buzzer volume OFF 1 5 114 Type of pellets Three different types of pellet can be set 1 3 130 Installer menu Sets displays the stove configuration PWD 54 140 Service menu Menu reserved for the service centre Submenus 30 and 40 the Setup menu are password protected and reserved for service centre personnel 7 2 USING THE CONTROL PANEL The arrow buttons are used to scroll between the different menus that are highlighted When selecting a given function any submenus available can be scrolled using the buttons to set a parameter simply use the button and modify the values again using the buttons Pressing the button confirms the setting n general all values that are flashing can be modified using the HO buttons The annulla button goes back up one level in the menu pressing and holding the button displays any active alarm or error codes 44 136 cod 004772531 07 2013 Palazzetti PN Italy USE AND amp MAINTENANCE PALAZ
48. uration the boiler modulates output according to the room temperature read by the probe on the boiler that is the boiler attempts to maintain the desired temperature while minimising fuel consumption If the user has enabled the Eco mode function under submenu 13 of the setup menu 13 the boiler rather than modulating its output switches off when reaching the set temperature and switches on again when the room temperature falls below the delta set in submenu 1 of the setup menu The desired room temperature can be set in temperature menu Submenu 6 J of the setup menu 3 can be used to the desired water outlet temperature the best temperature for the heating system in question should be suggested by the heating system installer OPERATION IN COMBINATION WITH A STORAGE TANK For operation in combination with a storage tank the installer will have set configuration 3 or 4 depending on whether the storage tank is with or without a coil inside The boiler is controlled based on the temperature read by the probe in the storage tank When reaching the storage tank temperature set in the temperature menu boiler switches off and switches on again if the temperature falls below the delta set in submenu of the setup menu 13 The frost protection function can also be set in this configuration 48 136 cod 004772531 07 2013 Palazzetti PN Italy USE AND amp MAINTENANCE PALAZZETTI 10 FUNCTIONS AV
49. utside If no fresh air opening can be made in the room it can be made in an adjacent room as long as the two rooms are connected by a ventilation grill Fig 5 4 C Shutter box G Grill S Shutters Standard UNI 10683 prohibits combustion air being drawn in from garages combustible material stores or places where there is a fire risk If there are other heating appliances in the same room the fresh air vents must guarantee the required volume of air for correct operation of all the appliances If one or more exhaust fans range hoods are installed and operating in the room where the stove is located combustion problems may occur due to a lack of combustion air In order to create the air intake it is possible either to Make the air intake hole on the wall and let the stove be free to withdraw air in the environment taking care however to connect on the air inlet tube the portion of corrugated pipe if provided supplied by fixing it with the clamp and bending it slightly downward Fig 5 5 connect the stove combustion air intake to the fresh air opening using a special pipe Fig 5 6 Fig 5 5 Fig 5 6 cod 004772531 07 2013 Palazzetti PN Italy 37 136 PALAZZETTI E EI 5 5 FLUE GAS EXHAUST The stove operates with negative pressure in the combustion chamber and consequently the flue gas discharge must be airtight The st
50. ve Combustion chamber burn pot or flue gas exhaust system irty Pressure measuring tubes detached or blocked Combustion air intake blocked lt Failed ignition error No pellets Faulty ignition heater Worn gaskets Incorrect burn pot position Only in the stoves equipped with micro safety switches on the firebox door and on the pellet hopper lid Only in the stoves without micro safety switches on the firebox door and on the pellet hopper lid After having checked the type of message the alarm can be reset by pressing the on off button If the error code is E108 or E109 before resetting the alarm manually reset the thermostat located on the rear of the stove Fig 11 1 for a few moments Then the stove can be started again Bx Fig 11 1 52 136 cod 004772531 07 2013 Palazzetti PN Italy USE AND amp MAINTENANCE PALAZZETTI 12 MAINTENANCE 12 1 SAFETY PRECAUTIONS Before performing any maintenance operations adopt the following precautions Make sure that all the parts of the stove have cooled down Make sure that the ash is completely extinguished Use the personal protective equipment specified by directive 89 391 EEC Make sure that the main power switch is off Make sure that the power supply cannot be reconnected accidentally Unplug the cord from the socket on the wall Always use suitable tools for maintenance Once maintenance or repa
51. zard to people and animals Liability for any harm caused to people or animals always lies with the owner When decommissioning the stove the ce mark this manual and other documents relating to this stove must be destroyed cod 004772531 07 2013 Palazzetti PN Italy 55 136 PALAZZETTI 14CONFIGURAZIONI DISPONIBILI AVAILABLE CONFIGURATIONS KONFIGURATIONEN ERH LTLICH CONFIGURATIONS DISPONIBLES CONFIGURACIONES DISPONIBLES KONFIGURACIJE NA VOLJO CONFIGURAZIONE 1 CONFIGURATION 1 KONFIGURATION 1 CONFIGURATION 1 CONFIGURACI N 1 S5 Nit 11 1 n Termostato esterno Wall thermostat Raumtemepratur Thermostat Thermostat externe Termostato exterior FF_rF r r FrFFhF hF hm ue quite Co C i j Componenti compresi nella stufa U I eee Components included in the stove 1 1 Komponenten enthalten in den Ofen d Composants prevus dans le po le Piezas incluidas en el kit estufa FI or CONFIGURAZIONE 2 CONFIGURATION 2 KONFIGURATION 2 CONFIGURATION 2 CONFIGURACI N 2 Sonda temperatura ambiente Room probe Raumtemperatur Fuehler Sonde temp

Product Brochure

Contents

Download Pdf Manuals

Related Search

Related Contents