Drill with TE DRS-S HEPA Dust Removal System
Contents
1. CPavnnsa TranssonooLDmsoN sape WORK PROCEDURE P with TE DRS S HEPA A Community of Learners Committed to Excellence Fi ltered Dust Removal System Page 1 of 4 Lorie Carriere Brent Vandenbosch Leon Prevost April 15 2014 Leon Prevost All Buildings PTSD Safety glasses or face shield must be worn at all Long and loose hair must be tied back and covered times in work areas Safety footwear must be worn at all times in Disposable P100 Respirator or a 2 mask respirator the work area with HEPA Filters wipes sanitizing pads if required Hearing protection must be worn when using Close fitting protective clothing must be worn this machine Remove strings hanging from pullovers sweaters Photo 1 v Lacerations abrasions cuts amputations Equipment orientation VY Foreign materials in concrete other objects Never leave machine running unattended v MSI injuries Use tools only for their intended purpose v Noise can product up to or greater than 92dBA Read and understand general safety procedures in the Y Discharge of objects material kickback user Manual v Electrical shock Drill with TE DRS S HEPA PEMBINA TRAILS SCHOOL DIVISION Qm A Community of Learners Committed to Excellence SAFE WORK PROCEDURE Filtered Dust Removal System Page 2 of 4 TOO 2 25 mm 6 Small extraction head 7 Large extraction head 8 Vacuum hose 33 50 9 Main section of the TE DRS S g 26 92 PAA ea ot 26 40 mm 10 Mounting2. don all personal protective equipment safety glasses face shield hearing protection safety footwear Remove all jewelry loose clothing and tie back hair DO NOT wear gloves when operating the drill 2 Make all adjustments with battery removed or the cord unplugged 3 Ensure that attachments example drill bits and auxiliary are securely attached 4 1 Depth gauge rod Fe 2 Extraction head 3 Position adjustment 4 Mounting clamp 5 HEPA vac hose Adjust the depth gauge rod on the drill so that it does not project beyond the chuck b Push the TE DRS S dust removal attachment onto the depth gauge rod and slide the mounting clamp up to the side handle of the drill c Adjust the extraction head until it is flush with the tip of the drill bit by opening the mounting clamp locking lever and sliding the tube forward or back until the head is flush with the tip of the drill bit Close the mounting clamp d Fit the extraction head onto the end of the TE DRS S and push into place Note you must use the appropriate size of extraction head for the size of the drill bit e Adjust the position of the head by pushing and turning until the point of the drill bit is centered within it f Connect the HEPA vacuum hose to the hose connector on the TE DRS S a Ensure power switch is on OFF position before plugging in Check that the cord is away from path of the tool Remove any wrenches and adjusting tools before turning
3. on a tool Hold hammer drill by insulated gripping surfaces and auxiliary handles Turn the HEPA vacuum on first Turn power for the drill to ON and allow motor to come to full soeed before using Anticipate torque on start up Begin drilling 9 Once drilling has finished slowly retract the drill through the HEPA vacuum head Try to remove all the dust from the drill bit Remove any remaining dust with a damp paper towel Once finished wrap up in a second paper towel and discard the waste O ee g Drill with TE DRS S HEPA PEMBINA TRAILS SCHOOL DIVISION Q A Community of Learners Committed to Excellence SAFE WORK PROCEDURE Filtered Dust Removal System Page 4 of 4 10 Turn power OFF and allow machine to stop before setting down Turn off the HEPA vacuum 11 Leave the machine in a safe clean and tidy state 12 Clean up the area 13 Return tools to proper storage location after use 14 When servicing equipment ex changing a bit power must be disconnected If an emergency situation occurs while conducting this task or there is an equipment malfunction shut the equipment off immediately and unplug the power tool REPORT ANY HAZARDOUS SITUATION TO YOUR SUPERVISOR IMMEDIATELY Mb Regulations 217 2006 Part 16 Machines Tools amp Robots Sections 16 1 16 18 WS amp H Act W210 Section 4 5 7 7 1 Operators Manual for the Drill and the TE DRS S Dust Extraction System
4. Clamp PER 11 Length Stop PRT p 12 Depth Gauge D BO D Te k CEES ae 13 Securing Clip e E aS eee 14 Hose connector 051 68 E 0 69 82 PRE OPERATIONAL SAFETY CHECKS Inspect required personal protective equipment and replace if required Ensure no slip trip hazards are present in workspaces and walkways Faulty equipment must not be used Immediately report suspect machinery Locate and ensure you are familiar with the operation of the ON OFF starter Disconnect power supply before changing or adjusting bits Ensure auxiliary handle is securely attached Use the correct drill bits for the work material Ensure insulated gripping surfaces are in working condition Ensure the HEPA vacuum is turned on prior to starting the drill Always use the dust extractor heads of the correct size for the drill bit in use 0 Allow the vacuum cleaner to run for a few seconds after drilling has finished to ensure that all the dust has been removed from the hose shake amp tap the hose to loosen dust and from the drill bit 11 Do not leave this equipment running while unattended 12 Do not use machine if it is damaged Immediately report any damages to your supervisor il aa aa a oe K PEMBINA TRAILS SCHOOL DIVISION SAFE WORK PROCEDURE Drill with TE DRS S HEPA A Community of Learners Committed to Excellence Fi j te red D u st Re m oVa i System Page 3 of 4 OPERATING THE DRILLWITH DUST REMOVAL ATTACHMENT 1 Inspect and
Download Pdf Manuals
Related Search