ION-E100 - User Manual
Contents
1. Resolution Allows you to select the video resolution of encoded images Target Bit Rate Allows you to select the target bit rate to be used by the codec Enabled This parameter allows you to enable or disable a video codec 3 JPEG Specific Codec Configuration Frame Rate Allows you to specify the frame rate to be used by the codec In JPEG this frame rate will be guaranteed regardless of the rate control setting Quality Allows you to select a value for quality of JPEG compression from 0 to 100 The higher the value the better the quality This setting is only applicable if the Rate Control parameter is set to Fixed Quality Rate Control Allows you to choose between Variable Bit Rate and Fixed Quality The first option will instruct the JPEG codec to prioritize bit rate over quality The second option will instruct the JPEG codec to use the specified quality setting and vary bit rate accordingly 4 H 264 Specific Codec Configuration Profile Allows you to select the H 264 codec profile from Baseline Main and High profiles Baseline does not contain all the optimization that enhances the visual quality of the video This profile is the one requiring the least video processing power Main Adds in loop deblocking filter and CABAC encoding Requires more processing power to encode and decode High Adaptive 8x8 or 4x4 transforms on the image Page 33 of 36 Ife NODES ION E100 User manual e T2. Configuration Please select from the following sub sections System Date Time Network Video In Audio In Audio Out Serial Ports Recording User Accounts Recorder Status Vj Enabled Current Recorder State Active Storage Profile Imnt mc mnt mc 3 8 GB reserved for recording General NVR Detection Mode Server Ping Ping Timeout 60 1 3600 s Ping IP Address 0 0 0 0 Grooming Mode Chronological Maximum File Duration 120 120 3600 s Maximum File Size 128 8 1024 MB Vides Input Selection Select a video input Board 1 video inputi All Video Inputs When selected this special input allows you to change one or more settings for all video inputs at once To do so select or enter a value for each setting you want to set and click the Save button Only settings for which val lied to all video inputs For all other settings each video input will retain its own individual valu Per Input Configuration Recording Status Recording Record Video From Primary H 264 Input Record Record Continuously v VO Event Input VO Event Input State Video Retention Time 30 1 365 days _ Force Immediate Deletion of Video After Retention Time _ Mute Audio The recording in the ION E100 is configured using only a few parameters e Enabled Determines whether recording on the edge is active e Current Recorder State Provides inf
3. From there the streams can be viewed live in real time recorded or both There are deployment scenarios that require the ION E100 to record audio video content to local storage instead of recording on an external video management system VMS There are also situations where the ION E100 simply cannot reach the VMS for a period of time There may be temporary network disruptions the video management system may be undergoing maintenance or there may be an attack on the security system in progress If external conditions prevent the ION E100 from streaming its media content when it is configured to do so the ION E100 can record the streams locally instead Once the situation returns to normal the recorded content can then be retrieved from the ION E100 Its storage capacity is limited but depending on selected quality it can record a few days or so of content at a time 8 1 Configuration Recording on the edge on the ION E100 can be configured through the device s web application To view or change the recording settings e Open the device s web application Enter your use name and password e Click on the Configuration tab e Inthe configuration page click on the Recording tab Page 25 of 36 fe NODES Ife NODES Home Configuration Diagnostics Maintenance Live Viewer Recording Information Product ION E100 Version 2 3 0 0 Up time 2d 23h 25m 06s User admin ION E100 User manual
4. User manual 1 create the negative data signal please connect Rx and Tx pins together on the Terminal Bloc Socket 2 To create the positive data signal please connect Rx and Tx pins together the Terminal Bloc Socket 3 To ensure proper connection between RS 485 2 wire serial equipment and the ION E100 use the following scheme Equipment Serial Port ION E100 Serial Port Data Data Data Data GND GND Page 12 of 36 Te NODES ION E100 User manual 5 Understanding LED Status The following describes the system status LED mappings of the ION E100 Normal Operation e Operating system boot up LED is steady orange max 30 seconds e Internal application startup LED is flashing orange 2 second interval e lON E100 system ready LED is steady yellow e Media streaming LED is flashing yellow 1 2 second interval Special Operations e Identify command received LED is flashing orange yellow e Hardware reload default settings LED is flashing rapidly red yellow e Software watchdog is rebooting the appliance LED is flashing rapidly red e Firmware update in progress LED is flashing slowly red yellow Page 13 of 36 DES ION E100 User manual 6 Initial System Configuration For initial set up the ION E100 needs to be configured prior to using it with your network video management system In most cases only network configuration will be required Sin
5. ION E100 Web Application When entering the Web Application you will be asked a username and password The default user name and password is admin The following window will be displayed e NODES Home Welcome The following web interface has been designed to help you perform certain administrative tasks needed to keep your device properly configured and operational Use the tabs on the len to select the administrative section you want Each section provides further instructions Note The information box found on the left side bar contains basic information about this device Information Proouct ION ET1600 Version 2000 Up time Od 00h 22m 50s User admin The following parameters may need to be programmed before using the unit 1 An NTP time server address 2 Video encoder streams Page 18 of 36 Te NODES ION E100 User manual Setting up the NTP server Under the Configuration section select the Network tab and set the proper NTP server address under the NTP Configuration header S NODES Configuring Video Parameters You may disable any of the three 3 video encoder streams Primary H 264 Secondary H 264 and MJPEG All other video parameters should be configured within your NVM system Note We recommend disabling the MJPEG codec if you do not intend on using this codec within your application This will avoid turning on this stream by inadvertence and possibly affecting the performance
6. input 8 3 Retrieval Management of Video Clips Recorded video on the ION E100 can be retrieved through the device s web application To view and manage the list of recorded video clips e Open the device s web page Enter your use name and password e Click on the Recording tab Page 28 of 36 Te NODES ION E100 User manual Recording Select a video input video input 1 Y Refresh All Time Format UTC time Zaj 2011 04 15 2011 04 20 Rees Select A Lock Selected Unlock Selected Delete Selected 8 3 1 Displaying Clips When you select a video input the web application displays a list of dates with video recorded from that input To display the list of recorded video clips for a specific date simply click on the date Click on the date once more to collapse the list of recorded video clips for that date By default the clip start times are displayed using UTC time If you want to see the start times in their local time equivalent simply select Local time in the Time Format setting 8 3 2 Downloading Clips To download a video clip simply click on the clip s description The video clip can then be played on the user s PC using an appropriate video player Downloading a clip does not remove the file from the device 8 3 3 Locking And Unlocking Clips A locked file cannot be deleted This serves as a protection against accidental deletion of important clips When the
7. of the device e ETHERNET PoE This is the ION E100 network port Please use a straight RJ45 cat 5 or 6 network cable The ION E100 accepts a Power Over Ethernet PoE compliant power source if needed e RESET The reset button can be used to perform a hardware reset or to perform a complete reset to default settings of the device s configuration parameters Page 10 of 36 Ife NODES 4 Serial Port Connectivity Many devices PTZ keyboards PTZ cameras ION E100 User manual use RS 422 485 protocols for communicating with other equipment These protocols are standards for binary data exchange between DTE and DCE equipments To connect serial equipment to an ION E100 using RS 422 485 4 wire configuration use the following steps 1 Connect twisted pair cables to the Terminal Bloc Socket located on the front panel of the device Connect to Tx Tx Rx Rx and GND 2 Select the desired operation mode RS 422 4 wire RS 485 2 wire or RS 485 4 wire using the devices web interface or external VMS interface 3 To ensure proper connection between RS 422 4 wire or RS 485 4 wire serial equipment and the ION E100 use the following scheme Equipment Serial Port TX TX RX RX GND RX RX TX TX GND ION E100 Serial Port To connect serial equipment to an ION E100 using RS 485 2 wire configuration use the following steps Page 11 of 36 JNO DES ION E100
8. recording on the edge needs to perform grooming see Configuration above the device checks for locks and will never delete locked clips when it needs to free up storage space Page 29 of 36 Ife NODES ION E100 User manual To lock one or more video clips you must first select each clip by clicking on the check box on its right If you want to select all the video clips for a day you can also click on Select All associated with that day When you have selected all the clips you want to lock for that day click on the button Lock Selected If you want to lock clips from more than one day you must repeat the process for each day Locked clips have a lock icon besides them To unlock one or more video clips select the video clips then click on Unlock Selected 8 3 4 Deleting Clips To delete one or more clips for a day select each clip you want to delete then click on Delete Selected If you want to delete clips from more than one day you must repeat the process for each day Trying to delete a locked clip does nothing If you want to delete locked clips you must first unlock them Page 30 of 36 Te NODES ION E100 User manual 9 Point to Point Connections Point to point connections between an ION E100 and an ION R100 can be configured using the device s web application In the ION E100 s web application in the Configuration section go to the Video In tab and select video input 1 Scrol
9. 0 150 1 169 254 150 150 eth0 Local Video 1 Out 0 In i Out 0 Ind Out 0 1 Out 0 1 0 Out 0 Inn 16 Out 0 In 16 In 16 Out 0 ION E100 User manual i Toos S 1 0 Serial Port 2 Out 1 1 2 Out 1 In 2 Qut 1 In 2 Qut 1 0 Qut 0 In 16 Out 4 Inn 16 Qut 4 In 16 Out 4 To start a firmware update session choose the iof file corresponding to the new firmware by clicking to the Select File button Once selected click to the Start button Firmware Update Session Firmware File Serial Number 100 1100 8000 009 E100 3100 4000 0070 E100 1100 8000 008C IP Address 10 190 200 10 10 190 210 10 10 190 200 12 Select File Once started the Firmware Update Session window shows the progress of the firmware update This window can be closed at any moment without losing the current session Page 23 of 36 Ife NODES ION E100 User manual If closed the progress of the current session can be followed by reopening the Firmware Update Session window by clicking the button from the Tools toolbar Once done clear the current session from the Firmware Update Session window and restart a new session if needed Page 24 of 36 Te NODES ION E100 User manual 8 Recording on the Edge In most setups the ION E100 is used to stream video and or audio to an ION R100 or to a central video management system VMS
10. 0 is not in good working order lonodes will at its option repair or replace it at no additional charge except as is set forth below In some cases the replace ment product may not be new and may have been previously installed Regardless of the replace ment product used lonodes appropriate warranty terms apply In case lonodes or your reseller are unable to repair an lonodes ION E100 you can alternatively ask for a partial refund as far as justified by the reduced value of the unrepaired ION E100 or ask for a cancellation of the respective agree ment for such ION E100 and get your money refunded Extent of Warranty The warranty does not cover the repair or exchange of an ION E100 resulting from misuse accident modification unsuitable physical or operating environment improper maintenance by the end user or failure caused by a product for which lonodes is not responsible The warranty is voided by removal or alteration of ION E100 or parts identification labels but not by the installation or replacement of Micro SD medium THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND REPLACE ALL OTHER WARRANTIES OR CONDITIONS EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Items Not Covered by Warranty lonodes does not warrant uninterrupted or error free operation of an ION E100 Any technical or other support provided for an ION E100 under warra
11. 00 or 1727580000 Note When unpacking inspect the shipment box and appliance to identify any possible damages due to shipping Make sure all items have been delivered and that no items are missing Contact your lonodes representative should you find any damag es or defects Note The product serial number label helps the lonodes product support team identify your device and its factory configuration in the event that your ION E100 or its com ponents require service The label is attached on the underside of the enclosure Page 5 of 36 Ife NODES ION E100 User manual 2 Hardware Installation 2 1 Equipment Installation The ION E100 can be placed on a flat surface such as a desktop or mounted via the available mounting holes When installing the ION E100 position the unit to allow for cable clearance at the front and rear of the unit Make sure that minimal air flow is provided to the unit The ION E100 can be mounted to various mounting structures via the available mounting holes Note that mounting screws are not shipped with the device Page 6 of 36 Te NODES ION E100 User manual 3 Connections Familiarize yourself with the ION E100 front and rear panels before connecting any equipment to the unit The ION E100 offers a single analog video input and associated l Os and audio connections 3 1 Front Panel e VIDEO IN BNC connector interface for video input source NTSC PAL e MICRO SD
12. 10 Serial Port 169 254 118 1 ION E100 2107 1 I1 Out 1 2 Out 1 1 Page 16 of 36 KAN O DES ION E100 User manual If no DHCP server was able to assign an IP address to an ION E100 it will appear in the ICT device list with an APIPA address 169 254 If an ION E100 displays an APIPA address it must be configured with a valid IP address before it can be remotely configured by selecting the Assign IP address from the selection list and configuring the TCP IP settings 1O NODES Configuration Tool 6 Discovery 3 Networks M 10 190 150 1 169 254 150 150 eth0 Local i Toos AX Serial Number IP Address Type Version Video Audio 1 0 Serial Port 100 3100 4000 001 m on 100 2 1 0 7 1 1 Out 0 1 1 Out 1 12 Out 1 1 Assign IP Address es Firmware Update Identify Device lt Configuration Web Page Restart Device s IP Address Assignment Start Address Subnet Mask 255 Gateway 0 Status Page 17 of 36 Ife NODES ION E100 User manual Once the IP information is set the Silverlight web application served by the ION E100 can be launched from the ICT or directly in your web browser by typing the device s IP address in the address bar You can start to use your networked video management system for final system configuration or you can configure advanced parameters using the ION E100 s web based management 6 2 Using the
13. Ife NODES DOCUMENT APPROVED FOR GENERAL DISTRIBUTION ION E100 User Manual Version 1 7 fe NODES The smart appliance of media IONODES INC Laval Qu bec Canada www ionodes com Ife NODES Table of Contents 1 BEFORE YOU BEGIN neri aceite dee acie iiic n uates iie CI E I iUc 4 14 ABOUT THEON ETOO niiina neea trate tp vesc tera Pet deed to arse artes ca RR ae 4 1 2 PARTS EIST E 5 2 HARDWARE INSTALLATION 6 2 1 EQUIPMENT INSTALLATION 6 3 CONNEC THONG 7 3 1 a Ee a a 7 MEM CI IT 8 4 SERIAL PORT CONNECTIVITY 11 5 UNDERSTANDING LED STATUS reru rte tein ott adita nt cu uot ed annee es ennenen nnana 13 Pr 13 Special 13 6 INITIAL SYSTEM CONFIGURATION 14 6 1 NETWORK CONFIGURATION ccccccccccccecsessesecescescecseseeaeceseescceseaaeseceesesceeseaaeseeessesceeseaaeceeeeseeenes 14 6 2 USING THE ION E 100 WEB 18 Setting up the NTP Server ed idea essai ior edad aia v
14. aa e a gd d a Rad deben 19 Configuring Video Parameters 19 7 PERFORMING A FIRMWARE UPDATE 21 7 1 BATCH FIRMWARE UPDATE ssessssseseeeeenee enne entren nntn en tene 22 8 RECORDING ON THE natn snis nasa snnm assa ias asia 25 8 1 We PH M 25 8 2 AUDIO RECORDING cms 28 8 3 RETRIEVAL MANAGEMENT OF VIDEO CLIPS enne nennen nennen nnne nene 28 8 3 1 Displaying dieere tie n tune dern btn cleo 29 8 8 2 Downloading 29 8 8 8 Locking And Unlocking nnne nennen nns 29 8 34 Deleting i ea add e ende ca elt 30 9 POINT TO POINT CONNECTIONS e eeeeeeeeeeee eene nn nennen intr antra annia nunnur ennnen sme anne 31 Te NODES ION E100 User manual ANNEX A CONFIGURATION PARAMETER REFERENCE eere eene 32 ANNEX B TROUBLESHOOTING 35 ANNEX C STATEMENT LIMITED WARRANTY cernerent 36 Page 3 of 36 Ife NODES ION E100 User manual 1 Before you begin 1 1 About the ION E100 The ION E100 single port encoder delivers high quali
15. adjust the strength or purity of color of the video input Saturation represents the amount of gray in proportion to the hue On the standard color wheel saturation increases from the center to the edge The saturation filter lets you adjust the saturation of the entire image e Brightness The brightness filter allows you to set the black level of the captured video input It controls the darkest detail that you can see and how dark those details look If it is set too high then everything will seem washed out and dull and if it s set too low then you won t be able to see the detail in shadows e Contrast The contrast filter is usually configured once brightness is adjusted Contrast allows you to control how bright the bright details get on the captured video input e Deinterlacing The deinterlacing filter is used to convert interlaced video such as common analog video signals into a non interlaced form that can be viewed on progressive displays such as computer monitors e Video Standard The video standard allows you to select the video source as NTSC or PAL e Audio Association This parameter allows you to associate a specific audio input with this video input Page 32 of 36 Ife NODES ION E100 User manual Enabled This parameter allows you to enable or disable a video input 2 Video Codec Configuration H 264 amp JPEG Enabled This parameter allows you to enable or disable a video codec
16. ce not all ION E100 parameters can be controlled via networked video management systems advanced parameters may need to be set up as well through the ION specific software tools The initial configuration can be done locally on the ION E100 using a laptop directly connected to the device s network port or remotely over the network 6 1 Network Configuration By factory default the ION E100 is configured in DHCP If you are not using a DHCP server it will automatically allocate itself an APIPA Automatic Private IP Addressing address in the range 169 254 0 1 to 169 254 255 254 with subnet mask 255 255 0 0 Initial device network configuration is done via the lonConfigTool ICT a tool provided by IONODES and that can be found on the company s web site The ICT plays 5 important roles 1 Discovery of all ION E100 and other ION devices on the network 2 Remote configuration of the IP address and subnet mask 3 Identify an ION device by flashing the LED orange yellow 4 Batch firmware upgrade of all common ION devices 5 Access to the web based ION management application Page 14 of 36 Te N O DES ION E100 User manual Once your device is installed on your network and powered up launch ICT from any computer on the network and the following window will be displayed The ICT supports 2 ways to discover a device The first way doesn t need any configuration and uses the Bonjour discovery protocol In order to be able
17. d time and to itz only for the tme Page 20 of 36 Te NODES ION E100 User manual 7 Performing a Firmware Update This section describes how to update your ION E100 to newer firmware versions from the web application 1 Navigate to your device s web application using your favorite web browser 2 Olick on the Maintenance tab 3 Click on the Update button You will be asked for the firmware update file please select the iof file which was provided by IONODES ITI m 4 You will see the following messages indicating the status of the update o Firmware upload in progress 100 Lasts around 95 seconds Status LED is green o Firmware uploaded Saving to internal storage 0 Lasts around 45 seconds Status LED is flashing red green Validating and decompressing firmware 0 Lasts around 105 seconds Status LED is flashing red green o Firmware ready for installation Rebooting device 0 Web page will disconnect from device until device has rebooted will be prompted for login once the device is up again Lasts around 110 seconds Status LED is orange o Testing firmware stability 2696 Lasts 120 seconds Status LED is flashing red green o Firmware update complete 10096 Page 21 of 36 JNO DES ION E100 User manual 7 1 Batch Firmware Update This section describes how to perform a batch update of multiple ION E100 devices to newer firm
18. e internal storage space of the ION E100 is full the system automatically deletes recorded video files for which the retention period has expired See below Requires that all video inputs be configured with a retention time e Maximum File Duration While recording video the recorder stores video in clips no longer than this duration e Maximum File Size While recording video the recorder stores video in clips no bigger than this size The recorder also includes some per input configuration e Recording Status Indicates whether the video input is currently being recorded or not e Record Video From Determines which video encoder to record for the video input e Input Record Mode Determines under which conditions to record video from the input o Do Not Record Never record video from the input o Record Continuously Always record video from the input o Record On Event Record video from the input when at least one of the follow ing conditions is met Record When Connection Is Lost Record video when the network connection to the NVR server is lost See NVR Detection Mode above Record On Demand Record video when requested manually Manual recording can be activated from the Live Viewer web page or through the lonAPI Record On Motion Event Record video when a least one motion region of the input is triggered Record I O Event Record video when a specific I O input pin see Event Input reaches the specified sta
19. he visual difference is much greater between baseline and main then between main and high Also the differences appear only when the visual quality begins to degrade ex when the quality begins to degrade on baseline profile switching to main profile will restore some of the image quality e Frame Rate Allows you to specify the frame rate to be used by the codec e Rate Control Allows you to choose between Variable Bit Rate and Constant Bit Rate The first option will instruct the H 264 codec to dynamically adjust the bit rate in order to meet both the target quality QP and frame rate settings The second option will instruct the H 264 codec to prioritize target bit rate and vary quality QP first and frame rate as a last resort e Min Max This parameter allows you to specify the compression range that the codec will use to determine image quality during compression In order to force a specific quality setting you can set the minimum and maximum to the same value The lower the value the better the quality will be e VBR Aggressiveness This parameter allows you to specify if the codec should take into account the level of motion in the image for bit rate calculations You can select from Conservative Moderate and Aggressive options for this setting Using the first option the codec will allow bit rate to drop up to 34 of the configured target bit rate when no motion is detected in the image Using the second option
20. l down all the way to the bottom of the configuration page The last 3 sections are named Point to Point 1 2 and 3 Here s a quick overview of the settings available for a connection e Enabled Indicates whether this connection is to be used e Description Free form user description of the connection not used by the device e Encoder Indicates which video feed is to be sent over the point to point connection Possible values include H 264 High Quality and H 264 Low Quality These values refer to the encoders configured in previous sections of the same web page e Destination IP Address where to send the video This is usually the address of an ION R100 The destination can also be a multicast group address DNS names are not yet supported only IP addresses e Destination Port Network port where to send the video This value must match the port value in the ION R100 Once all the settings have been set click on Save at the bottom of the page to apply them The ION E100 then creates or updates the connection as needed Page 31 of 36 Te N O D ES ION E100 User manual Annex Configuration Parameter Reference 1 Video Input Configuration e The hue filter allows you adjust the hue of an entire image Hue is the color reflected from or transmitted through an object It is measured as a location on the standard color wheel e Saturation The saturation filter sometimes called chroma allows you to
21. nty such as assistance via telephone with how to questions and those regarding ION E100 set up and installation will be provided WITHOUT WARRANTIES OF ANY KIND
22. of the H 264 codecs Page 19 of 36 Ife NODES ION E100 User manual Please select from tne to select from Ine folowing sub sections Configuration System Date Time Network Video In Sensi Ports Recording System Time Network Video In Audio in Audio Out Serial Ports te ding User Accounts Video input Selection Video Input Selection a video video Select a input vdeo input 1 Preview Information uct Uptime 09008 11m 486 User somn Brightness 50 Contrast Denteriaceg Region 1 sociated aud Select a Regon of Compression Enabled Select An Encoder Primary 4 264 Regen Position 0014 iY Enable encoder Frame Count 4 1 Prote Sonetnaty Resolution Frame skip rate JA Threshold A 100 Target bi ra Privacy Zones mage Rate control Minimum 16 5 5t 16 5 intra interval VER Aggressi aggresive z Mutcost iP Point to Point Seisct Connecton Font to Point 1 Enabled Description Encoder Primary 4 264 z Refresh Destnation IP 0000 Enable Select a Privacy Destnation Port 0 Text Overtay Image ected String Medum String Positon 00 String Text Seti to Tor current date an
23. optional Micro SD connector available for edge recording capability Please insert a formatted FAT micro SD card to enable associated functionality Page 7 of 36 Ife NODES ION E100 User manual 3 2 Rear Panel 1 1 1 1 e Terminal Bloc Header This header connector is used to connect the supplied Terminal Bloc Socket which provides the interface to serial port and power connections Below is a detailed view of this Terminal Bloc Socket Relay Output Digital Input Pins 1 amp 2 Receiver pair for serial communication 4 wire RS 422 or RS 485 Transmitter pair for serial communication 4 wire RS 422 or RS 485 12V power source Page 8 of 36 Te N O DES ION E100 User manual The pin out description of the Terminal Bloc Socket is as follows Number Description Direction 1 RL Relay Out 2 RL Relay Out 3 I1 Digital Input 1 In 4 I2 Digital Input 2 In 5 RX In 6 RX In 7 TX Out 8 TX Out 9 12V supply In 10 Ground e AUDIO IN OUT 3 5 mm jack which can be used to connect both an audio input and an audio output source The stereo channel provided by this connector exposes one channel for the audio input and the other for the audio output GND IN ter OUT rcn e STATUS The system status LED is a bi color Yellow Orange LED providing detailed Page 9 of 36 Ife NODES ION E100 User manual information on the current state
24. ormation of the current state of the recorder Possible states include dle Rebuilding Index and Active e Storage Profile Lists the storage available for recording When the recorder is disa bled it is also used to change the recording storage selection Page 26 of 36 Te NODES ION E100 User manual e NVR Detection Method Determines how the ION E100 is to detect when it loses its connection to the video management server o Server Ping The ION E100 actively polls the IP address of the server for a reply to ensure that the address is present on the network This method is independ ent from the type of video management server o Internal API The ION E100 uses the communication protocol of the video man agement server to detect its presence Currently supported Genetec protocol e Ping Timeout Time to go without any response from the server before declaring the connection lost This parameter is only visible when NVR Detection Method is set to Server Ping e Ping IP Address IP address of the server to poll This parameter is only visible when NVR Detection Method is set to Server Ping e Grooming Mode Determines how the recorder is to recycle storage space when the ION E100 needs to record video on the edge o Chronological When the internal storage space of the ION E100 is full the sys tem automatically deletes older recorded video files as needed so that new video can be recorded o Input Retention Time When th
25. te see O Event Input State e Event Input I O input pin to monitor for On I O Event recording for the video input Page 27 of 36 Ife NODES ION E100 User manual e Event Input State input pin state required to activate On I O Event recording for the video input e Video Retention Time Period of time in days to preserve recorded video for the video input e Force Immediate Deletion after Retention Time When checked forces the recorder to delete the recorded video for the input as soon as its retention period expires even if the recording storage is not full e Mute Audio When checked if the video input has audio associated to it the audio will be muted 8 2 Audio Recording Video recording can be configured to simultaneously record an associated audio input stream This said the system does not allow you to ONLY record audio content it can only allow you to record audio in addition to a video stream The association between an audio input and a video input is done as follows e Open the device s web application Enter your use name and password e Click on the Configuration tab e Inthe configuration page click on the Video In tab e Locate the configuration parameter called Associated audio and select the audio input you wish to associate with the video input e Click on the Save button to save your changes e The associated audio input will now be recorded simultaneously to its parent video
26. ted Warranty apply only to ION E100 products purchased from an authorized lonodes Inc lonodes Reseller Integrator or Distributor and returned from European Asian or North American countries and excludes all Latin American countries The term ION E100 means an ION E100 module any module upgrade or accessories or any combination of them The term ION E100 does not include any software programs whether pre loaded with the ION E100 installed subsequently or otherwise and any installed Micro SD Card which are covered by a separate Limited Warranty Nothing in this Statement of Warranty affects any statutory rights of purchaser that cannot be waived or limited by contract If you have any questions regarding this Limited Warranty contact lonodes Inc and its resellers The Warranty period for the ION E100 is 2 years from date of billing for the ION E100 product The lonodes Warranty for ION E100 lonodes warrants that each ION E100 is free from defects in materials and workmanship and con forms to the ION E100 Official Published Specifications See http Awww ionodes com for details The warranty period for an ION E100 is a specified fixed period commencing on date of billing by lonodes for the Product If a valid proof of billing cannot be found the warranty may be void by lon odes Inc or measured from the date the ION E100 has shipped from a lonodes Depot center based on its serial number If during the warranty period the ION E10
27. the codec will allow bit rate to drop up to 12 of the configured target bit rate when no motion is detected in the image Using the first option the codec will allow bit rate to drop up to of the configured target bit rate when no motion is detected in the image You can disable this feature by selecting the disabled option Page 34 of 36 Ife NODES ION E100 User manual Annex B Troubleshooting Guide e Device does not seem to boot up Verify that 12V 40W power supply is connected to the device If using PoE verify that the RJ45 network link is properly providing power When a valid power source is detected the status LED will light up Verify the status of the system status LED to determine the state of the device as it powers up e Cannot discover the device or communicate via the network Before the device be discovered the status LED must be lit YELLOW as this indicates ready state of the device Make sure you have connected the device to your network Make sure the GREEN LED on the RJ45 connector is lit If it is not lit verify the network connectivity with the network switch Dynamic discovery of the ION E100 requires multicast networking to be supported by your network and switch equipment Bonjour protocol Page 35 of 36 Ife NODES Annex B Annex C Statement Limited Warranty The warranties provided by lonodes Inc lonodes in this Statement of Limi
28. to discover a device via Bonjour the network must support multicast delivery If it is not the case you can use the second way which is the Unicast Discovery The Unicast Discovery can be configured by using the Unicast Discovery configuration form This configuration form is available via the Admin Unicast Discovery menu option 1O NODES Configuration Tool il m Credentials Networks yey 10 196 31 100 Wireless Network Connection v Englis _ IP Address Type Version Video Serial Port Page 15 of 36 fe NODES Unicast Discovery ION E100 User manual Start Address EndAddress Ping Timeout ms 10 190 210 1 10 190 210 255 To configure the Unicast Discovery add one or more IP address ranges The Unicast Discovery tries to reach a device at a specific IP address in the configured ranges The discovery can be a long process if the range of IP addresses is huge and the device is at the end of the range To accelerate the discovery add several small ranges of IP addresses The ping timeout option can be increased for a high latency network The ICT will display as many devices as it discovers on the network 1O NODES Configuration Tool DER 9 Search Domain A local Discovery Serial Number Networks 2 10 190 150 1 169 254 150 150 eth0 Local v Tools 9 EIA 9 IP Address Type Version Video Audio
29. ty H 264 video encoding to the video surveillance market It is an embedded high performance digital video encoder capable of encoding an analog camera input using multiple profiles at a combined 90 images per second NTSC PAL at 4CIF resolution Embedding support for networked API s the ION E100 can be integrated into a networked video management system allowing for centralized monitoring and management in a scalable and expandable IP surveillance system Contact IONODES for a list of supported VMS systems The high performance encoding capability of the ION E100 offers a cost effective way to service existing analog cameras while providing the benefits of video over IP networks The ION E100 provides innovative configuration options and tools that can significantly decrease the amount of time and effort required to deploy a unit Using web based configuration tools users can easily and remotely manage all aspects of the appliance To support high performance encoding while keeping the total cost of ownership within budget constraints the ION E100 uses highly efficient dual stream H 264 compression and supports an optional third MJPEG stream Advanced features such as edge recording and video analytics allow you to extend usage of the ION E100 well into the future Page 4 of 36 KAN O DES ION E100 User manual 1 2 Parts List Qty Description 1 ION E100 appliance 1 Terminal block socket P N Weidmuller 17276600
30. ware versions from the ICT The batch firmware update works by starting a firmware update session Only one session at time is allowed and only 20 devices can be selected by session From the ICT select one or more devices of the same type 10 NODES Configuration Tool DER Device Discovery Discovery Networks 53 10 190 150 1 169 254 150 150 eth0 Local iTos db S 6 5 5 Serial Number IP Address Type Version Video 120 Serial Port amp Search Domain f E100 1100 8000 0008 10 190 200 13 ION E100 2200 Int Ow0 I2 Dut1 1 a V4 E 100 1100 8000 009E 10 190 200 10 ION E100 2200 1 12 Out 1 10 190 210 10 ION E100 2200 Int Ow0 I2 Out 1 10 190 200 12 ION E100 2200 Int 2 Dutt 220001 16825448191 ION E1600 0123 0 10 f 0000 0022 CB00 3012 10 190 200 40 ION E1600 2101 16 1 16 0464 f 0000 0022 CBD0 2FFE 10 190 200 41 ION E1600 2200 16 1 16 Dut 4 f 0000 0022 CB00 133E 10 190 210 40 ION E1600 2200 In 16 1 16 Dut 4 By using the right mouse button on the selected devices choose the Firmware Update menu option Page 22 of 36 10 NODES Configuration Tool E Device Discover lt EN Q Search Domain local Discovery Serial Number IP Address f E100 1100 8000 0008 10 190 200 13 10 00 f 0000 0022 CB00 1398 64 Restart Device s Version 2 2 0 0 2 2 0 0 Networks 53 10 19
Download Pdf Manuals
Related Search