cg800h-sky series skynet 2000 control panel user manual
Contents
1. for central control Optional AC 220V Neutral for Zero crossing detection STEP 4 Connect the Belden 8723 cable wires and the power wires and then fix the product on the wall box according to the following diagram Important Before plugging the Button panel onto the Bracket double check the Dip Switch located at the back of the Button panel to see whether the address is equal to the label located at the front of the button panel If there is no address label at the front of the Button panel please add an address label to it This address label will be for future use during the SkyNET Planner programming Address label Button panel Cn os co Screw x 4 pcs Screw x 2 pcs BELL From doorbell for CG800HHB SKY BELL RS485B From Belden 8723 Green RS485A From Belden 8723 White 12V From power cable Black 12V From power cable Red STEP 5 At the last panel of the RS485 bus the last one of the daisy chain add a termination resistor of 1200hm 1 4W across the RS485A and RS485B terminals to terminate the data transmission impedance STEP 6 For the SkyNET 2000 main unit connection of cable and power wires connection please refer to the SkyNET 2000 User Manual STEP 7 Double check if all wiring is correct then power up the main switch board the LED indicators on CG800H SKY series will be lighted up for one second if you push the button once Since the2. CG800H SKY is not programmed and setup by SkyNET Planner Software at this moment the product buttons will not function at this stage ONIONIONION JO NONO ONION SBAS B88 Ele OFFPFFDFFPFFI IpFFbEFFPFF OFFIOFA Notes Use standard UK wall box BS4662 minimum 35mm deep During installation of the wall box it is recommended to embed the wall box deeper inside the wall in order to give more room to install the product The room inside is recommended to have 50mm deep 7 Operation instruction 7 1 CG100H4 SKY 4 Button Mood Control Panel 1 1 2 3 4 are buttons location 4 pcs Locks to fix the main unit onto the wall bracket Reset button Program port Button 1 2 3 4 can be programmed to be ON OFF function or Dim up Dim Down or Scene function It can be programmed via SkyNET Planner Software Push these button to activate the function The backlit icons on the button will light up LED ON indicates the Function is ON LED OFF indicates the Function is OFF 10 7 2 CG800HHB SKY Doorbell switch Doorbell button Clean Room Indicator For Hotel Only Do Not Disturb For Hotel Only 4 pcs Locks to fix the main unit onto the wall bracket Reset button 7 Program port When Doorbell button is pressed the dry contact output for bell will be momentary on for 1 seconds during this 1 second duration the bell will be driven on and d
3. DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons product The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the O IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards There are however some installation and operation precautions which you should be particularly aware of A a a a a Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus that produce heat Do not defeat the safety purpose of the polarized or grounding type plug If the provided plug does not fit into your outlet consult an electrician for replacement of the outlet Protect the power
4. CG800H SKY SERIES SKYNET 2000 CONTROL PANEL USER MANUAL CG800H1 SKY CG100H2 SKY CG800H4 SKY CG800HHB SKY 1 button mood 2 button mood 4 button mood Doorbell switch control panel control panel control panel VERSION 1 1 17 JANUARY 2014 CityGrow Systems Disclaimers and Copyright Nothing contained in this publication is to be construed as granting any right by implication or otherwise for the manufacture sale or use in connection with any method apparatus or product covered by letters patent or as insuring anyone against liability for infringement of letters patent Efforts have been made to ensure the accuracy and reliability of the data contained in this publication however Citygrow Energy Systems Limited makes no representation warranty or guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or from the use of any product or methodology described herein for any violation of any federal state or municipal regulation with which this publication may conflict or for the infringement of any patent from the use of this publication Nothing contained in this publication should be viewed as an endorsement by Citygrow Energy Systems Limited of any particular manufacturer s products Copyright 2012 Citygrow Energy Systems Limited All Rights Reserved CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK
5. HUW EU I DC 12V s AC 220V Distribution board M Neutral II Live Power supply I aa LA CO x N a4 For CG800HHB SKY only 2V Neutral System 1 m AC Live Neutral a Dry contact control 6 Installation In order to install the product correctly please follow the below steps STEP 1 IMPORTANT Turn off main power at the main switch board ONIONJONION JO NONP ONION SABA B855 Ele OFFDFFPFFPFFI IpFFPFFPFF JOFFIOFF STEP 2 Loosen the screws of the original wall switch Remove the switch and the wiring STEP 3 Pull the Belden 8723 cable and 1 pair of Dia 1 5mm copper wire power cable black and red color from the location of the SkyNET 2000 main unit to the wall box location of the panel panels Please note if you have more than 1 wall box location that will be installed with CG800H4 SKY panel the Belden 8723 cable and the power cable should be ready at each of the wall box location The cables at the second wall box location should be pulled from the first wall box location such that they are in daisy chain configuration CG801SKN M SkyNET 2000 Main Unit If MTT Daisy chain EN N us To Loads HSE Wall lamps mount curtains nPa UUUUIII W control fan coils TTT are NOT To Loads panni allowed i 4 fan coils HUHH N lamps DC 12V curtains To LAN
6. SkyNET 2000 2000 Function 1 preset lighting scene for CG800H1 Build in contactor to drive AC door bell SKY LED backlight 2 preset lighting scene for CG800H2 Support two way function ie Different SKY doorbell switch can be located at different 4 preset lighting scene for CG800H4 locations SKY Lighting scenes is able to include IR control IR device purchase separately Lighting scenes is able to include curtain control Max 150 devices included in a scene Minimum dimming level preset Memory dim function Two way control function LED backlight Remarks Remarks 1 When up button is used for dimming 1 For hotel customer DND and Clean room up function the down button cannot LED indicator is provided on CG800HHB be programmed as scene function SKY Maximum number of devices programmed into the whole product is limited to 150 devices Maximum current 200mA max consumption Power supply DC12V Powered by SkyNET 2000 system power supply RS485 A amp RS485B to Panels should be connected in daisy chain configuration Maximum 32 control panels can SkyNET 2000 be connected Connect RS485 A and RS485 B to the corresponding pins Panel in Main unit It is recommended to use Belden 8723 cable RS485 terminator 1200hm resistor is needed to be added to end the cable See wiring diagram SkyNET 2000 Address setting Dip switch 1 to 8 for setting the panel address Normally the main unit CG801SKN M should be se
7. cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Table of Content Ws IN 0 0 3 0 6 PEPREREPERPREBERDEEREEENBDEBEBERERLEEBEREELEEEEREELHSENPEEEEEREEEEHEHLDEBEREDEEUECHEEENERLDSDERERCEEE 1 2 Understanding of the product CG800H4 SKY zzuenennnnnnnnnnnnn nn nn anne nn nun nn nn nn nenn nn nn nn 2 3 Understanding of the product CG10OOHHB SKY u2222222nnnnnnnn nenn nn nn nn nn nn nn nn nn nn nennen 3 4 MNS T VSI UNG a ee 4 De NVIAING e 5 5 TMSEAINAUIOMN oeeccesint sq ee aan een 7 7 Operation INstr clion sauna 10 7 1 CG100H4 SKY 4 Button Mood Control Panel ususuunnnnnnnnnnn nn nn nn nn nn nn nn nn nn nn nn nn nn nn 10 7 2 CG800HHB SKY Doorbell switch 2u022202220020nen0nn Ran nano
8. nnn nenne nnnennnn nennen 11 8 Programming the SkyNET system z22u222s0n02nnnnnn nn nn nn nn nn nn nn nn nn nn nn nn nn nenn nn nenne 12 I PEME OM een anne 13 1 Introduction Thank you for buying Citygrow s product CG800H SKY Series is both powerful and easy to use and install Description L 2 Wall mount control panel for SkyNET2000 Data communicates through RS485 bus and running on Citygrow s SmartBus protocols LED indicator for on off status CG800H1 SKY CG800H2 SKY CG800H4 SKY main function is to preset lighting scenes for SkyNET 2000 Control button can be configured to become two way function Control button can be configured to become scene function Control button graphics can be tailor made per customer requirement Mounted in a standard UK wall box Easy to install 10 Power supply by external DC12V powered by SkyNET 2000 system power supply CityGrow Systems 2 Understanding of the product CG800H4 SKY Frame al Button panel front view Button panel bottom view Control button Reset button Dip Switch for address setting Programming port Connector to Bracket Bracket Mounting bottom view hole a e Model number Metal clip J 7 yo plate to fix i the button panel Connector to button panel RS485B RS485A 3 Understanding of the product CG100HHB SKY Frame nn Button panel front view Button panel bottom
9. oorbell will ring for 1 second If CG800HHB SKY is selected to be used for hotel project see diagram above the Do Not Disturb or Clean Room LED indicator can be programmed to be switched on when the preselected button on a CG800H4 SKY panel is being pressed down Push the Doorbell button to activate the doorbell function the backlit icons on the button will light up LED ON indicates the Function is ON LED OFF indicates the Function is OFF 11 CityGrow Systems 8 Programming the SkyNET system Remove one of the button panel from the wall then you will see the wall bracket is still fixed on the wall box Then prepare a PC with SkyNET Planner Software installed and run it connect the CG101UT5 and CG100UTC cable from PC to the CG101TP SKY Tools Panel See following diagram STEP2 Plug the CG101TP SKY Tools Panel on the wall y bracket STEP 1 Select one of the wall mount panel and remove the frame and the keypad STEP 3 Connect CG101UTU and CG101UT5 cable from the PC to the 5 pin connector of The CG101TP SKY Tools panel PC installed with SkyNET Planner Software and USB to 5 pin run it conversion cable STEP 4 Refer to the user manual of SkyNET Planner Software to program and set the address of the product 12 9 Specification CG800H1 SKY CG800HHB SKY CG800H2 SKY CG800H4 SKY Description 1 2 4 button mood control panel for SkyNET Doorbell switch for
10. t to 00000000 In case Circuit Extender CG801SKN E is added the Circuit Extender can be set to 00000001 00000010 etc Control panel addresses can be 00000100 00000111 00000101 etc Please refer the SkyNET Planner user manual for details Dimensions mm 85x85x28 Length x Width x Depth Recommended 0 to 40 degC operation temperature
11. view Control button Reset button Dip Switch for address setting Programming port Connector to Bracket Bracket gt oS bottom view Mounting hole en 7 Model number Metal clip 1 f 7 plate to fix the button panel Connector to button panel BELL BELL RS485B RS485A 12V 12V CityGrow Systems 4 Dimensions 25 5mm 5 Wiring Before getting started gt gt gt gt WARNING It must be installed by a qualified electrician in accordance with all applicable regulations and building codes Improper wiring can result in personal injury or damage to control units or other equipment Always turn off circuit breaker or remove main fuse from power line before doing any work To avoid overheating and possible damage to equipment WARNING Do not operate when any lamps removed or burned out replace any burned out lamps immediately use only transformers that incorporate thermal protection or fused primary windings This product is designed for residential and commercial use for indoor use only WARNING Install in accordance with all national and local electrical codes IMPORTANT Citygrow is not liable for any damage incurred with the misuse of this product Wiring Diagram CG801SKN M SkyNET 2000 Main Unit Daisy chain RS485 nn bus Ir IN E wall Do NI e amp mount iil control l panels h
Download Pdf Manuals
Related Search