Internet Telephony PBX System - PLANET Technology Corporation.
Contents
1. 2 1 Safety Instructions The following are the safety instructions for Internet Telephony PBX system before installing m The maximum operating temperature of the IPX 2100 is 10 45 C Care must be taken to allow sufficient air circulation m The connections and equipment that supply power to the IPX 2100 should be capable of operating safely with the maximum power requirements of the IPX 2100 In the event of a power overload the supply circuits and supply wiring should be become hazardous m The power adapter must plug into the right supply voltage Make sure that the supplied power voltage is correct and stable If the input power voltage is over 10 lower than the standard it may cause the IPX 2100 to malfunction E Generally when installed after the final configuration the product must comply with the applicable safety standards and regulatory requirements of the country in which it is installed If necessary consult for technical support 2 2 Physical Introduction Internet Telephony PBX System Figure 2 1 Front Panel of the IPX 2100 Figure 2 2 Rear Panel of the IPX 2100 Supporting 2 slots user can buy expansion module like VIP 21FO 4 x FXO or VIP 21SL 2 x FXO 2 x FXS for extending port service 2 3 LED amp Button definitions LED definitions Front Panel LED Status Description PWR Steady Green PBX Power ON Off PBX Power OFF sys Blinking Green System is wo2. 2013 Contents are subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners This page is intentionally left blank This page is intentionally left blank
3. 198 Subnet Mask 233 Z233 239 0 Gateway 192 168 1 254 Primary DNS 192 168 1 254 Alternate DNS Virtual Interface Op Addressv1 o o Subnet MaskV1 Op Addressv2 Subnet Maskv2 Figure 3 4 Selection of IP Connection Type 3 3 Changing IP Address or forgetting admin password To reset the IP address to the default IP Address 192 168 0 1 ETH or reset the login password to default value Press the reset button on the front panel for more than 6 seconds After the device is rebooted you can login the management WEB interface within the same subnet of 192 168 0 xx Console Reset Button After pressing the Reset button all the system data will be reset to default if possible back up the config file before resetting 9 e 4 Further Configuration Thank you for purchasing PLANET products The above steps introduce the simple configuration of the IPX 2100 For further configuration please refer to the user s manual on the CD If you have other questions please contact the local dealer or distributor where you purchased this product You also can browse our online FAQ resource at the PLANET Web site first to check if it could solve your issue If you need more support information please contact PLANET support team PLANET online FAQ http www planet com tw en support fag php Support team mail address support_voip planet com tw Copyright PLANET Technology Corp
4. Internet Telephony PBX System IPX 2100 Quick Installation Guide Table of Contents 1 Package Contents pas cuseatnaccussatadinonigdiedernantigiatepndivienmaiiapaasmeabimenaganadeamanagaarent 3 2 Hardware installation sn iii a ia 4 2 1 Safety INStructiOns aria pibe lanas 4 ZZ Physical I MEFOAUCHOM racial 4 2 3 LED amp Button Gennitions iai tac cis eet relied aad dea ara diate 5 ZA Paco MENE ona 5 2 37 PnYsical CONNECCION ari rola aia 6 3 Basic System Cong Mira 7 Sik Web o Maia ies 7 3 2 Configuring the Network Setting seisce trnns eni a 8 3 3 Changing IP Address or forgetting admin password ooccoccccnccncnncnncncnnanano 9 4 Further CONQUE ii aaa 10 1 Package Contents Thank you for purchasing PLANET Internet Telephony PBX system IPX 2100 This Quick Installation Guide will introduce how to finish the basic setting of connecting the web management interface and the Internet Open the box of the Internet Telephony PBX system and carefully unpack it The box should contain the following items IPX 2100 x 1 e Quick Installation Guide x 1 User s Manual CD x 1 Power Adapter x 1 12V e RJ 45 x 1 e Bracket x 2 If any of above items are damaged or missing please contact your dealer immediately 2 Hardware Installation The following are instructions for setting up PLANET IPX 2100 Refer to the illustration and follow the simple steps below to quickly install your Internet Telephony PBX system
5. fault IP address of the IPX 2100 192 168 0 1 into the URL address box Step 4 Enter the default user name admin and the default password admin then click Login to enter Web based user interface Default IP Default ETH IP 192 168 0 1 Default User Name admin Default Password admin PLANET internet telephony Pax system Username Password aT PTE English v Figure 3 1 Login page of the IPX 2100 For security reason please change and memorize the new pass word after this first setup 7H 3 2 Configuring the Network Setting Step 1 Go to Network Settings Network Static Routing gt VPN Server gt VPN Client gt DHCP Server gt DDNS Settings gt SNMPv2 Settings gt Troubleshooting Figure 3 2 Network amp Country button Network Ethernet Port Setup IP Assign Static Hostname IPPBX IP Address 192 168 1 198 Subnet Mask 255 255 255 0 Gateway 192 168 1 254 Primary DNS 192 168 1 254 Alternate DNS Virtual Interface Op Addressv1 _ Subnet MaskV1 Op Addressv2 __ Subnet MaskV2 Figure 3 3 Network Setting page Step 2 Edit your ETH port IP information There are three types of Ethernet port connection They are Static IP PPPoE Point to Point Protocol over Ethernet DHCP You can find detailed setting process in the user manual Network Ethernet Port Setup IP Assign Hostname i Static IP Address j epee
6. rking Off System is off ETH Blinking Green PBX network connection is established Off Waiting for network connection Steady Red Ready Standby FXO Flashing Ringing Off Module not available Steady Green Ready Standby FXS Flashing Ringing Off Module not available USB Void Future Feature Button Action Description Press less than 5 secs System reboot Reset Press over 6 secs Reset to Factory Default 2 4 Placement Make sure the device is placed in a safe environment to avoid equipment failure m DO NOT place anything on top of the device Excessive weight could damage it m DO NOT obstruct ventilation slots on each side of the IPX 2100 or expose it to direct sunlight or other heat source Be sure that there is adequate air flow around the IPX 2100 m Place the IPX 2100 on a flat surface to avoid any damage 2 5 Physical Connection FXO Card fi dl 3 Router aa SABES a y la la gt Mobile Video Phone ATA IP Phone IP Phone SIP Phone Le a Telephone wire 100Base TX UTP SLT Phone FAX Figure 2 3 Physical Connection Topology of the IPX 2100 3 Basic System Configuration 3 1 Web Login Step 1 Connect a computer to an ETH port on the IPX 2100 Your PC must set up to the same domain as 192 168 0 X as the IPX 2100 Step 2 Start a web browser To use the user interface you need a PC with Internet Explorer version 6 and higher Firefox or Safari for Mac Step 3 Enter the de
Download Pdf Manuals
Related Search