phm-111-e / phm-111-ec advanced syringe pump
Contents
1. Files Currently on the CD Cw DoD B drivers header files Labview MED PC YEG CHAPTER 8 Alarm Settings Audible Alarm When enabled the Audible Alarm sounds when the automatic shut off switch is activated The volume level low and high and interval between alarm beeps 0 5 39 seconds are user defined It is important to note that the audible alarm functions only when pump is being operated in FORWARD mode n order to clear this alarm and resume pump operation squeeze the tabs on the slide assembly and move it back until the automatic shut off switch is deactivated Safety Timer The Safety Timer can be used to disable the pump if the MED PC input is on longer than the user defined Safety Timer duration The Safety Timer duration can be set to 1 99 seconds The lighted ON OFF switch Figure 2 8 will go out to indicate that the Safety Timer has been activated To clear the Safety Timer once it has been activated the pump must be turned off using the lighted ON OFF switch For the remainder of this section the pushbuttons switches will be referred to as follows Figure 8 1 Switch Numbering for Alarm Setting 24 View Default Alarm Settings To view the current alarm settings on the LCD Display the RUN STOP REMOTE switch should be set to STOP Switch 1 should be set to 9 and Switch 3 should be set to O as shown in Figure 8 2 Figure 8 2 Viewing Current Alarm Settings 8 99 8 8 Change De2. BOX 178 2 54 O O PUMP_ON CLEAR 1 1 SHOW 2 Update Resp B gt 53 Turn the Pump on in Reverse with a Rate of 178 RPM and Syringe Size of 2 54cc K3 B t PHM111 RampUpdate MG BOX BOX 178 2 54 0 0 0 PUMP REV 7 CLEAR 1 1 SHOW 2 Update Resp B gt 3 Turn the Pump on with a Starting Rate of 178 RPM Syringe Size of N 2 54cc and Ending Rate of 50 RPM It will take 0 34s to go from X the Starting Rate to the Ending Rate K4 B PHM111 RampUpdate MG BOX BOX 178 2 54 0 0 34 50 PUMP RAMP CLEAR 1 1 SHOW 2 Update Resp B gt 53 Turn the Pump on with a Starting Rate of 178 RPM Syringe Size of N 2 54cc and Ending Rate of 50 RPM It will take 0 53s to go from X the Starting Rate to the Ending Rate K5 B PHMILI RampUpdate MG BOX BOX 178 2 54 0 0 53 50 PUMP RMPDOS CLEAR 1 1 SHOW 2 Update Resp B gt 2 Turn the Pump on with a Starting Rate of 178 RPM Syringe Size of 2 54cc and Ending Rate of 50 RPM The Pump will calculate how long and fast to Ramp until 1cc is delivered K6 B PHM111 RampUpdate MG BOX BOX 178 2 54 1 0 50 PUMP RMPDOS CLEAR 1 1 SHOW 2 Update Resp B gt 2 Turn the Pump on with a Rate of 178 RPM and Syringe Size of 2 54cc N until 1cc is delivered K7 B PHM111 RampUpdate MG BOX BOX 178 2 54 1 0 0 PUMP DOSE CLEAR 1 1 SHOW 2 Update Resp B gt 2 Turn the Pump on with a Rate of 178 RPM and Syringe Si
3. Program K1 S S 1 Turn on the Pump at the Currently Selected Values S S 2 Turn off the Pump K2 S S 1 Turn the Pump on with a Rate of 178 RPM and Syringe Size of 2 54 pO S S 2 Turn off the Pump set the Rate to 50 RPM and set the Syringe Size to 2 54cC K3 S S 1 Turn the Pump on in Reverse with a Rate of 178 RPM and Syringe Size of 2 54cc S S 2 Turn off the Pump set the Rate to 50 RPM set the Syringe Size to 2 54cc and Reset the Pump to the Forward Direction K4 Turn the Pump on with a Starting Rate of 178 RPM Syringe Size of 2 54cc and Ending Rate of 50 RPM It will take 0 34s to go from the Starting Rate to the Ending Rate K5 Turn the Pump on with a Starting Rate of 178 RPM Syringe Size of 2 54cc and Ending Rate of 50 RPM It will take 0 53s to go from the Starting Rate to the Ending Rate K6 Turn the Pump on with a Starting Rate of 178 RPM Syringe Size of 2 54cc and Ending Rate of 50 RPM The pump will calculate how long and fast to Ramp until 1cc is delivered K7 Turn the Pump on with a Rate of 178 RPM and Syringe Size of 2 54cc until 1cc is delivered K8 Turn the Pump on with a Rate of 178 RPM and Syringe Size of 2 54cc for 0 34s K9 The first command sends the Pump a Rate of 178 RPM Syringe Size of 2 54cc and a Dose size of 1cc The second command turns on the Pump for the lcc Dose K10 The first command sends the Pump a Rate of 178 RPM Syringe Size of 2 54cc and a Infusion D
4. 8 turn the pump on Changes to the pushbutton settings will not be recognized if the RUN STOP REMOTE switch is in the RUN position Pre Programmed Syringe Brands 2a The PHM 111 pump is pre programmed with syringe settings for several common syringe brands and sizes Refer to Table 5 1 To use one of these syringe types set the SYRINGE BRAND pushbutton switch by selecting the number that corresponds to the brand Refer to Table 5 1 Figure 5 3 SYRINGE BRAND Pushbutton Switch SYRINGE BRAND Table 5 1 Syringe Brand Key SYRI NGE BRAND Corresponding Syringe Upper Left of LCD Pushbutton Setting Brand Display will read 0 Unknown Brand Select Units 1 BD Plastipak BD PLASTIC 2 Monoject MONOJECT 3 Terumo TERUMO 4 BD Glass BD GLASS B Unimetrics UNIMET 6 Hamilton ul HAMLTON ul I Hamilton ml HAMLTON ml 8 Popper amp Sons P amp S 9 Alarm Setting ALARM The Brand Name selected is displayed in the upper left corner of the LCD display Proceed to Step 3 Other Syringe Brands 20 the brand of syringe being used is not included in Table 5 1 set the SYRINGE BRAND pushbutton to zero With the SYRINGE BRAND pushbutton set to zero the SIZE pushbutton switch may be used to select the distance time that the pump travels see Table 5 2 The LCD display will read Select Units with the units being some measure of distance time Refer to Figure 5 4 In this case the infusion rate in volume time must be calculated by mult
5. E Light will be On if the pump is operating in FORWARD mode e Flashing if the pump is operating in REVERSE mode Off if the infusion is complete or the pump is off Out Of Range Light Figure 2 7 Red OUT OF RANGE Light OUT OF RANGE The OUT OF RANGE Light will be e On if the selected INFUSION RATE is out of range e On ifthe INFUSION RATE switches are set to 000 00 e Flashing if the Automatic Shut Off Switch has been activated Off if the pump is operating correctly or the pump is powered off Lighted ON OFF Switch Figure 2 8 Lighted ON OFF Switch The Lighted ON OFF Switch will be On if the pump is plugged in and switched on Off if the pump is switched off and or unplugged e Off if the automatic shut off switch is activated or the safety timer is activated CHAPTER 3 Syringe Placement Care should be exercised that the syringe is positioned correctly when loading the infusion pump Accurate flow rates cannot be assured if the syringe is not properly loaded It is also important that the slide assembly be making contact with the syringe plunger Complete the following steps to properly load the syringe A Move the slide assembly to the rear toward motor section by squeezing the tabs as shown in Figure 3 1 Figure 3 1 Moving the Slide Assembly B Open the syringe clamp and place the syringe barrel into the clamp as shown in Figure 3 2 Figure 3 2 Open Syringe Clamp C Be
6. Hamilton ul 50 ul 50 ul 100 ul 100 ul 250 250 ul 500 ul 500 ul Hamilton ml 2 5 5m 5m 10 mi 25 ml 25 mi 25 ml popper amp Sons 8 lmi Imi 2m 2m 3m 5mi 10 mi 20 30 50ml SYRI NGE SI ZE Pushbutton Setting BRAND Sizes displayed in black will be infused in cc hour Sizes displayed in red will be infused in ul minute Sizes displayed in blue will be infused in ul hour Set the desired INFUSION RATE using the pushbutton switches Figure 5 6 The INFUSION RATE is displayed on the bottom left corner of the LCD display The unit of the INFUSION RATE is also displayed on the lower right of the LCD display Verify that all settings are correct see Figure 5 7 Figure 5 6 INFUSION RATE Pushbutton Switches INFUSION RATE Select FORWARD or REVERSE mode using the FORWARD REVERSE switch on the front of the pump Figure 2 2 In FORWARD mode fluid is pumped out of the syringe and in REVERSE mode fluid is drawn into the syringe It is important to note that the FORWARD REVERSE switch remains active when the pump is switched to RUN so that the direction can be changed during an infusion NOTE The automatic shutoff switch is active only when the pump is operating in FORWARD mode Verify that the desired pump settings are correct using the LCD display and make any necessary changes Figure 5 7 Viewing the LCD Display SYRINGE BRAND SYRINGE SIZE INFUSION RA
7. PHM 111 E PHM 111 EC ADVANCED SYRI NGE PUMP OPERATORS MANUAL DOC 032 Rev 1 6 Copyright 2009 All Rights Reserved MED Associates Inc P O Box 319 St Albans Vermont 05478 www med associates com MED ASSOCIATES INC PHM 111 OPERATORS MANUAL TABLE OF CONTENTS CODE Le 1 1 Sarl a 2 PUM OVERVICW 2 RUN STOP REMOTE Switch 3 SYRINGE BRAND SIZE and INFUSION RATE Switches 4 FORWARD 7 REVERSE SIENS dia dia baies 4 Automatic S nana a en ae a 4 ei aa 6 OU OR ON AN 6 Lighted ON OFF Switch meme eee nnns 6 CIAL OE 3 asivure sake EXEC CUN E SERE ERI oo 7 sane i a NO TT TT EE E ET A E E 7 CHapter 9 DOC eei 9 CSS SR Ba de a a a a doc HE 9 eleg enrages 9 ITI LUI 10 OEM 10 Fa OC COR E E a a 11 MED PC Controlled Operation ss 16 USB Controlled Operation PHM 111 EC Only 17 TAPES O e 18 Driver and Software Installation ae mers d
8. Pump with the Ramp Rates provided It will take 0 53s to go from the Starting Rate to the Ending Rate K12 B PHM111 RampUpdate MG BOX BOX 178 2 54 0 0 53 50 PUMP_CALRAMP A PHM111 PumpRamp MG BOX BOX SHOW 1 Ramp Resp A 2 Update Resp B gt S2 Check if the Rate value supplied is valid for the Syringe Size X supplied K13 A PHM111 CheckRate MG BOX 50 2 54 CLEAR 2 2 SHOW 1 Rate Resp A gt 32 THESE COMMAND TURN OFF THE PUMP S3 Turn off the Pump K1 A PHM111 PumpStop MG BOX BOX CLEAR 2 2 SHOW 1 Stop Resp A gt 52 Turn off the Pump set the Rate to 50 RPM and set the Syringe Size to 2 54400 K2 B PHM111 RampUpdate MG BOX BOX 50 2 54 0 0 0 PUMP_OFF CLEAR 1 1 SHOW 2 Update Resp B gt 52 Turn off the Pump set the Rate to 50 RPM set the Syringe Size to X 2 54cc and Reset the Pump to the Forward Direction K3 B PHM111 RampUpdate MG BOX BOX 50 2 54 0 0 0 PUMP RESET CLEAR 1 1 SHOW 2 Update Resp B S2 Definitions of PHM 111 Commands PHM111 nit initializes the PHM 111 pump and returns the number of pumps attached to the driver Syntax PHM111 Init MG Where MG MED PC Global Parameter Exa
9. TE INFUSION UNITS 10 Switch RUN STOP REMOTE switch to RUN The pump will infuse at the set rate in the selected direction FORWARD or REVERSE and the green OPERATE light will come on solid green in FORWARD flashing green in REVERSE If the INFUSION RATE selected is out of range the red OUT OF RANGE light will come on and the pump will not operate If 000 00 is selected on the INFUSION RATE pushbutton switch the Pump will not operate Changes made to any of the pushbutton switches while the pump is in RUN mode will not be recognized until the pump is switched to STOP If the OUT OF RANGE light is on and the pump settings cannot be changed be sure that the RUN STOP REMOTE switch is set to STOP When the end of the syringe is reached in FORWARD mode the automatic shut off switch will stop the infusion the red OUT OF RANGE light will flash and if the Audible Alarm is enabled it will sound see Chapter 8 MED PC Controlled Operation This section describes the procedure for using MED PC 28 Volt output to turn the pump on and off When controlling the pump using MED PC the infusion parameters are set using the pump interface as described below The PHM 111 EC pump is also capable of more sophisticated computer control via the USB port Refer to USB Controlled Operation for more detailed information regarding the USB control of the PHM 111 EC pump 1 Connect the MED OPERATE port Figure 5 2 on the pump to any ava
10. command Runs the pump at Start cc hr rate in the forward direction Runs the pump at Start cc hr rate in the reverse direction Enter a Start cc hr rate and either a Dose cc or Time min value Pump will turn on at the Start cc hr rate and stop after the Dose cc or Time min has been completed whichever value has been entered Enter a Start cc hr rate End cc hr rate and Time min The infusion will begin at the Start cc hr rate and in the Time min duration the rate will gradually ramp up to the End cc hr rate The pump will continue to run at the End rate Enter a Start cc hr rate End cc hr rate and Dose cc or Time min The infusion will begin at the Start cc hr rate and ramp up to the End cc hr rate until the Dose cc has been delivered or the Time min is up depending on which value has been entered The pump will stop when the RAMPDOSE command is completed Table 7 1 Syringe Cross Sectional Areas Syringe Size Cross section UNI METRICS glass Cross section 05 mL 0 00833 sq cm Syringe Size 10 mL 0 01667 sq cm B D PLASTI PAK plastic ECT plastic 0 173 sq cm 0 622 sq cm TERUMO plastic C header and library files are available on the USB Syringe Pump Test Program CD to provide further information on the operation of the software The available header and library files are shown in Figure 7 2 Figure 7 2 Header and Library Files on CD
11. dard with USB Syringe Pump Test Program Software for testing functionality and interfacing the pump with third party or custom software The PHM 111 EC is also compatible with Razel IPC software which is an option for users desiring a fully stand alone USB controlled pump CHAPTER 2 Pump Overview Figure 2 1 Top of the PHM 111 Series Pump SYRINGE STOP BRAND INFUSION RATE RUN REMOTE TE 0 000 00 OPERATE OUT OF RANGE Figure 2 2 Front of the PHM 111 EC Pump med ASSOCIATES INC PHM 111 EC FORWARD 1 REVERSE Figure 2 3 Syringe Components PLUNGER Figure 2 4 Pump Mechanism Components Slide Assembly Clamp Slide Assembly Syringe Clamp RUN STOP REMOTE Switch When the switch is in the RUN position 1 The pump operates at the set rate and in the set direction 2 The SYRINGE BRAND SIZE or INFUSION RATE pushbutton switches are disabled Changes made to these settings while the pump is in RUN mode will not be recognized 3 The direction of the pump can be changed using the FORWARD REVERSE switch 4 The green light is on if operating in FORWARD mode and flashing if operating in REVERSE mode When the switch is in the STOP position 1 The SYRINGE BRAND SIZE and INFUSION RATE pushbutton switches are enabled These settings may be adjusted as desired when in STOP mode 2 The direction of the pump can be selected using the FORWARD REVERSE switch 3 The gr
12. een OPERATE light is off When the switch is in the REMOTE position and Controlled Using a 28V Operate Signal from MED PC 1 The pump operates at the set rate and in the set direction as long as the output from a MED PC interface is on 2 The SYRINGE BRAND SIZE or INFUSION RATE pushbutton switches are disabled 3 The green OPERATE light is on if operating in FORWARD mode and flashing if operating in REVERSE When the switch is in the REMOTE position and USB controlled PHM 111 EC only 1 All switches but the RUN STOP REMOTE switch are disabled 2 The USB connector is enabled 3 The pump is completely controlled by commands received via the USB port 4 The green OPERATE light is on if operating in FORWARD mode and flashing if operating in REVERSE SYRI NGE BRAND SIZE and I NFUSI ON RATE Switches These switches are used to select the desired syringe type and infusion rate The function of these switches is described in detail in Chapter 5 FORWARD REVERSE Switch When the switch is in the FORWARD position 1 The pump pushes fluid from the syringe 2 The green OPERATE light is on when the pump is switched to RUN When the switch is in the REVERSE position 1 The pump draws fluid into the syringe 2 The green OPERATE light is flashing when the pump is switched to RUN Automatic Shut Off Switch When the pump is operating in FORWARD mode an internal automatic shut off switch stops the infusion when the pump
13. f the catheter infusion site is below the height of the syringe To test for these two conditions it is suggested that the syringe be connected to the tubing and held vertically at the height of the pump no motion occurs the syringe can then be placed in the pump The following may reduce the danger of an uncontrolled infusion 1 Lower the relative height of the infusion pump in relation to the infusion site With the pump below the infusion site the instrument will pump the fluid to the higher elevation 2 Use a smaller bore catheter which will reduce the weight of the fluid in the tubing and increase the friction on the flowing fluid 3 Use a syringe with a rubber seal on the plunger i e an O ring sealed or plastic syringe Small Syringes Syringes of less than 5 ml capacity can be held more securely in the syringe clamp if the R ACC Micro Syringe Adapter is used This insert slides into the standard syringe clamp and can hold two micro syringes CHAPTER 5 Operating Instructions Figure 5 1 Pushbutton Switches Figure 5 2 Back of the PHM 111 EC Pump 28V DC o CI BK n MED USB OPERATE PHM 111 EC ONLY NOTE The PHM 111 can be operated using 24 28 VDC LOCAL Operation 1 Apply power to the pump by plugging the A C power adapter into the 28 VDC Connector Figure 5 2 Be sure that the RUN STOP REMOTE switch is in the STOP position Using the green ON OFF switch Figure 2
14. fault Alarm Settings To make changes to the alarm settings the following procedure should be followed 1 Set the RUN STOP REMOTE switch to STOP and Set Switch 1 to 9 and Switch 3 to Ll as shown below Figure 8 3 Changing Audible Alarm Settings 225 2 Use Switch 2 to select the desired alarm function as shown in Table 8 1 Table 8 1 Switch 2 Settings Switch 2 Function LCD Display 0 Safety Timer Off SET SAFETY OFF 1 Safety Timer On SET SAFETY ON 2 Audible Alarm Off SET ALARM OFF 3 Audible Alarm On Low SET ALARM LOW 4 Audible Alarm On High SET ALARM HIGH 5 Audible Alarm On High SET ALARM HIGH 6 Audible Alarm On High SET ALARM HIGH 7 Audible Alarm On High SET ALARM HIGH 8 Audible Alarm On High SET ALARM HIGH 9 Audible Alarm On High SET ALARM HIGH 3 Use Switches 6 and 7 to set either the interval between Audible Alarm occurrences or the duration of the Safety Timer 4 The Audible Alarm interval can be 0 5 39 seconds If it is desired that the Audible Alarm sound every 30 seconds Switch 6 should be set to 3 and Switch 7 should be set to 0 The LCD will display this value as DELAY 30 sec Setting Switches 6 and 7 to 00 will produce an interval of 0 5 seconds Figure 8 4 Alarm Display 26 MED ASSOCIATES INC PHM 111 OPERATORS MANUAL 5 Verify that the settings are correct and set Switch 3 to 2 to save the changes ALARM SAVED will be displayed on the LCD If changes need to be made t
15. gram CD into the CD ROM drive The screen shown in Figure 6 1 will appear Click Install the USB Syringe Pump Test Program and the screen shown in Figure 6 2 will appear Figure 6 1 USB Syringe Pump Test Program CD Menu USB Syringe Pump API amp Test program MEO associates inc USB Syringe Pump API amp Test program Install the USB Syringe Pump Test program Extras Browse the CD Exit To begin driver and software installation click Install Follow the steps to complete installation When the driver and software are installed the screen will appear as shown in Figure 6 3 Figure 6 2 Installation Checklist USB Syringe Pump Test Program Install Wizard med ASSOCIATES ING Welcome to the install wizard for USB Syringe Pump Test Program The wizard will install USB Syringe Pump Test Program on your computer To continue click Install R100P111 Pump Driver USB Syringe Pump Test Program instrumentation and software for research Cancel Green checkmarks indicate successful installation If a red X appears next to any item contact MED Associates Customer Support The USB driver and software installation is now complete Click Finish to close this screen and proceed to the device driver installation Figure 6 3 Installation Checklist Complete USB Syringe Pump Test Program Install Wizard Me il ASS0OCIATES INE Install Wizard Complete The Install Wizard has successfully installed USB S
16. ight will flash and if the Audible Alarm is enabled it will sound see Chapter 8 9 If the Safety Timer is enabled the infusion will be stopped if the 28 Volt output from MED PC is on longer than the Safety Timer duration see Chapter 8 The lighted ON OFF switch will go out to indicate that the Safety Timer has been activated USB Controlled Operation PHM 111 EC Only To control the PHM 111 EC pump via USB the USB port on the pump must be connected to any available USB port on the computer using the included USB cable The pump may now be controlled via USB using either the USB Syringe Pump Test Program MED PC or Razel IPC software In order to control the pump using software the necessary drivers must be installed Refer to Chapter 6 For USB control the RUN STOP REMOTE switch must be set to REMOTE When the pump is in REMOTE mode and the USB cable is connected the computer USB port will control the pump and the FORWARD REVERSE switch and the pushbutton switches will be disabled CHAPTER 6 Driver and Software Installation Before the pump can be controlled using software the necessary drivers and software must be installed NOTE The PHM 111 EC driver is specific to the computer USB port that the pump is connected to during driver installation For this reason it will be necessary to complete driver installation again if the pump is connected to a different USB port at a later time Insert the USB Syringe Pump Test Pro
17. ilable output on the Standard MED Connection Panel e g SG 716D using the included cable 2 Apply power to the pump by plugging the A C power adapter into the 28 VDC Connector Figure 5 2 Be sure that the RUN STOP REMOTE switch is in the STOP position Using the green ON OFF switch Figure 2 8 turn the pump on Changes to the pushbutton settings will not be recognized if the RUN STOP REMOTE switch is in the RUN position 3 Refer to LOCAL Operation steps 2 6 Pages 11 15 for detailed instructions regarding the use of the pushbutton switches 4 Switch RUN STOP REMOTE switch to REMOTE The pump will infuse at the set rate in the selected direction FORWARD or REVERSE for as long as the 28 Volt output from MED PC is on 5 The green OPERATE light will come on solid green in FORWARD flashing green in REVERSE when infusing 6 If the INFUSION RATE selected is out of range the red OUT OF RANGE light will come on and the pump will not operate If 000 00 is selected on the INFUSION RATE pushbutton switch the Pump will not operate 7 Changes made to any of the pushbutton switches while the pump is in REMOTE mode will not be recognized until the pump is switched to STOP If the OUT OF RANGE light is on and the pump settings cannot be changed be sure that the RUN STOP REMOTE switch is set to STOP 8 When the end of the syringe is reached in FORWARD mode the automatic shut off switch will stop the infusion the red OUT OF RANGE l
18. inge Pump Test Program each pump must be connected to any available USB port on the computer Next plug each pump in using the 28V power adapter Setting the Pump Number Before turning the pumps on set Switches 1 and 2 refer to Figure 8 1 for the location of Switches 1 and 2 to the desired pump number This pump number will appear on the Select Pump pulldown menu and can be used to identify which pump is being programmed If the pump is being used with MED PC the pump number should correspond to the box number Be sure to switch each pump to REMOTE mode Now the pumps may be turned on Open the USB Syringe Pump Test Program and the screen shown in Figure 7 1 will appear Figure 7 1 USB Syringe Pump Test Program USB Syringe Pump Test Program EE Exit Al Select Pump e E Delay 7 Enable 254 Surngelsqcm 38 Loud 1 Start cc h 98 5 afetu sec ann 1 End cc hr API Status Continous v OK 51 Dose cc Invalid Pump ee 050 Timefmin Status Send Command Enable MED PE Status Time sec Infuse Steps Reverse Steps Daa Motor ON USE Ramp OF input ON Fomeard Dose Ok Limit Switch The cross sectional area of the syringe being used must be entered Syringe sqcm Table 7 1 contains the cross sectional areas of several commonly used syringes Pump Commands OFF ON REVERSE DOSE RAMP RAMPDOSE Turns the pump off and ends the
19. iplying the syringe pump speed distance time by the cross sectional area of the syringe being used see Table 7 1 For example Rate cc min Distance Time cm min x Syringe Cross Sectional Area cm It is important to note that the Distance and Syringe Cross Sectional Area must be in the same units and the time units must also agree Proceed to step 4 Table 5 2 Distance Time Selection En CE BRAND SI ZE Pushbutton Setting Pushbutton Setting 0 1 2 3 4 5 6 7 8 0 0 mm min mm hr cm hr in hr R 99EJM RPM 100 Hz Hz Hz Hz Figure 5 4 LCD Display with SYRINGE BRAND and SIZE Pushbutton Settings of 0 12 3 Once a selection has been made for SYRINGE BRAND set the SIZE pushbutton switch using Table 5 3 In Table 5 3 the sizes displayed in black will be infused in cc hour the sizes displayed in red will be infused in ul minute and the sizes displayed in blue will be infused in ul hour The SIZE is displayed in the upper right corner of the LCD display and the infusion units are displayed in the lower right corner of the LCD display see Figure 5 7 Figure 5 5 SIZE Pushbutton Switch SYRINGE SIZE 8 18 i8 8 8 Table 5 3 Syringe Size Chart SYRI NGE SIZE CHART SYRI NGE BRAND M 3m 3 6 12 mi 20 mi 35 60 mi 60 ml 3m 5 10 20 30 mi 60 mi 60 60 mi 60 ml lmi 2ml 5ml 10 mi 20 30 mi 50ml 50 ml
20. mple N by START PHM111_Init MG 52 PHM111 PumpStart starts the pump Syntax PHM111 PumpStart MG Box P1 Where MG MED PC Global Parameter Box MED PC BOX Parameter Pl Pump Number that this command is for valid values 0 24 Example 52 R Lever PHM111 PumpStart MG BOX BOX gt S3 PHM111 PumpStop stops the pump Syntax PHM111 PumpStop MG Box P1 Where MG MED PC Global Parameter Box MED PC BOX Parameter Pl Pump Number that this command is for valid values 0 24 Example S3 1 PHM111_PumpStop MG BOX BOX gt S2 PHM111 RampUpdate sets up pump parameters Syntax PHM111 RampUpdate MG Box P1 Start Rate Size Dose Time End Rate Code Where MG MED PC Global Parameter Box MED PC BOX Parameter Pl Pump Number that this command is for valid values 0 24 Rate cc hr Size Syringe Cross Sectional Area cm Dose cc Time Infusion Duration minutes Code Any of the following Code PUMP NULL Updates rate values only no change to PUMP ON OFF DIRECTION Pump rate changed if running PUMP OFF Turns pump off and leaves pump direction and speed alone PUMP ON Turns the pump on in FORWARD mode PUMP DOSE Turns the pump on and stops infusion after dose or time is complete PUMP INPUTON Enables remote MED PC Input control Example B PHM111 RampUpdate MG BOX BOX 50 2 54 0 0 0 PUMP NULL
21. o annees 18 Chapter 7 nas sens na EH RI E E OR 21 Running USB Syringe Pump Test Program 21 Pump CommandS didus Ud a da rand maU C raura ein 22 Chapter NINE 24 PANY SEUNG D ETET 24 AlL 24 TEE NEN 24 View Default Alarm Settings sus 25 Change MOT SOLITOS etidm ac th nas 25 ChapLer 9 ausssseskvFEXET4EUICEEEWNNCESSE NU CEEFEIUNVREEEEERERENVREFRUEVEEEVM 28 Sample MED PG Progra a c ae 28 Definitions of PHM 111 Commands UV 30 CHAPTER 1 Background The Med Associates PHM 111 Series Advanced Syringe Pumps ensure safe accurate infusion using several unique features The PHM 111 pump allows the user to specify a syringe brand and capacity as well as the desired infusion rate These settings are clearly displayed on an LCD for easy viewing For added safety the PHM 111 Series Advanced Syringe Pump utilizes an automatic shut off when the end of the syringe is reached Med Associates strongly encourages that this manual be read thoroughly prior to operating the pump Both the PHM 111 E and the PHM 111 EC Advanced Syringe Pumps offer the ability to control the operation of the pump either locally using the easy to use pushbutton switches or remotely using MED PC The PHM 111 EC may also be operated remotely via a computer USB port The PHM 111 EC Pump comes stan
22. o the alarm settings once ALARM SAVED has appeared on the LCD Switch 1 must be switched from 9 to any other setting Switch 3 must be set back to 1 then Switch 1 must be set back to 9 again Figure 8 5 Alarm Saved 27 CHAPTER 9 Sample MED PC Program Example Med State Notation code for the PHM 111 Advanced Syringe Pump Application is shown below for reference purposes This code is included on the PHM 111 CD The code must be translated and compiled using Trans IV prior to running it in MED PC Refer to the MED PC User s Manual and MED PC Programmer s Manual for detailed information Copyright C 2008 MED Associates All rights reserved PHM 111 PUMP MPC This program demonstrates how to properly call the MED PC commands that Start and Stop the PHM 111 Pump The BOX parameter specifies which PHM 111 Pump to start When this program is running in Box 1 then the BOX parameter will equal 1 and Pump 1 will start When this program is running in Box 2 then the BOX parameter will equal 2 and Pump 2 will start etc This allows the same program to be run in multiple Boxes and control different Pumps aA A A a DO TT TT TT TT TT TT TT TT TT TT TT 7 TT TT TT TT List Working Variables Here A Response from the PHM111 Init PHM111 PumpStart PHM111 PumpDose PHM111 PumpRamp PHM111 CheckRate and or PHM111 PumpStop Commands B Response from the PHM111 RampUpdate Command K Pulses Used in this
23. reaches the end of the syringe In addition the red OUT OF RANGE light will flash and if the Audible Alarm is enabled it will sound see Chapter 8 The automatic shut off switch uses an internal micro switch that detects when the slide assembly reaches a certain point This point is adjustable so that the pump can accommodate various sizes and brands of syringes To adjust the automatic shut off switch insert an empty syringe with the plunger at the desired shut off position Move the slide assembly to the rear of the plunger Figure 2 5A With the pump turned on rotate the adjustment screw Figure 2 5B until the OUT OF RANGE light comes on Each clockwise turn of the adjustment screw will cause the switch to activate 025 inches further and each counterclockwise turn of the adjustment screw will cause the switch to activate 025 inches sooner When the automatic shut off switch is activated the LCD display will read LIMIT Switch ON Pump OFF and the lighted ON OFF switch will go out In order to clear this message and resume pump operation squeeze the tabs on the slide assembly Figure 3 1 and move it back until the switch is deactivated NOTE It is important to note that there will not be any indication that the end of the syringe has been reached when operating in REVERSE mode Figure 2 5 Automatic Shut Off Switch Adjustment ADJUSTMENT SCREW a Operate Light Figure 2 6 Green OPERATE Light OPERATE The OPERAT
24. sure that the syringe tabs are properly inserted between the syringe clamp and the retaining posts and ensure that the syringe is loaded with the syringe tabs positioned horizontally 5 that they do not impede the travel of the slide assembly as shown in Figure 3 3 Figure 3 3 Properly Aligned Syringe Tabs CORRECTLY LOADED SYRINGE INCORRECTLY LOADED SYRINGE D Move the slide assembly to the end of the syringe and insert the plunger into the slide assembly clamp as shown When the pump is operating in REVERSE mode it is especially important that the syringe be loaded into the slide assembly clamp correctly Figure 3 4 Plunger Positioned in the Slide Assembly Clamp E Run the pump in FORWARD mode see Operating Instructions until the slide assembly makes contact with the plunger and the syringe tabs are in contact with the syringe clamp Refer to Figure 2 3 and Figure 2 4 CHAPTER 4 Specialty Syringes Glass Syringes Extra caution is needed when using glass syringes with a ground glass plunger These syringes exhibit almost no sliding friction and thus can cause an uncontrolled infusion in the following two ways 1 The weight of the plunger may be sufficient to push the fluid out of the syringe if the syringe is held with the plunger above the syringe 2 The weight of the fluid in the tubing may be sufficient to siphon the fluid out of the syringe i
25. uration Time of 0 34s The second command turns on the Pump for the 0 34s Infusion Duration Time Kit The first command sends the Pump a Starting Rate of 178 RPM Syringe Size of 2 54cc Ending Rate of 50 RPM and 1cc Dose The second command turns on the Pump with the Ramp Rates provided The Pump will calculate how long and fast to Ramp until lcc is delivered K12 The first command sends the Pump a Starting Rate of 178 RPM Syringe N Size of 2 54cc Ending Rate of 50 RPM and a Infusion Duration Time N of 0 53s The second command turns on the Pump with the Ramp Rates N provided It will take 0 535 to go from the Starting Rate to the N Ending Rate N K13 Check if the Rate value supplied is valid for the Syringe Size X supplied NECK k k k kc AR ck ck k k coke ck coke ke ee k k k k k k k k k k k k k k k k k THESE COMMAND TURN ON THE PUMP eee coke ck kk k k ck coke k k k ck ck k k k k I k k k k ck k k k ckckckck k k k k k k k S S 1 Initialize the Pump S1 Set a default Rate of 50 RPM and Syringe Size of 2 54cc START A PHM111 Init B PHM111 RampUpdate MG BOX BOX 50 2 54 0 0 O PUMP NULL SHOW 1 Init Resp A 2 Update Resp B S2 S2 Turn on the Pump at the Currently Selected Values HK1 A PHM111 PumpStart MG BOX BOX CLEAR 2 2 SHOW 1 Start Resp A gt 3 Turn the Pump on with a Rate of 178 RPM and Syringe Size of 2 54cc HK2 B PHM111 RampUpdate MG BOX
26. yringe Pump Test Program Click Finish to exit the wizard R100P111 Pump Driver x USB Syringe Pump Test Program instrumentation and software for research 19 Using the included AC power adapter connect the 28V DC connector on the pump to a standard wall outlet Using the included USB cable connect the USB connector on the pump to any available USB port on the computer Turn the pump on lighted ON OFF switch and the screen shown in Figure 6 4 will appear Select Install the software automatically Recommended and then click Next Figure 6 4 Found New Hardware Wizard Found Hew Hardware Wizard Welcome to the Found Mew Hardware Wizard This wizard helps vou install software for MED Associates PHM 111 Pump If your hardware came with an installation CD Ee or floppy disk insert it now What do you want the wizard to do 5 Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue When the screen shown in Figure 6 5 appears select Finish The driver installation is now complete Figure 6 5 Driver Installation Complete Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for MED Associates PHM 111 Pump Click Finish to close the wizard lt Back Cancel CHAPTER 7 Running USB Syringe Pump Test Program Prior to running the USB Syr
27. ze of 2 54cc X For 0 34s HK8 B PHM111 RampUpdate MG BOX BOX 178 2 54 O 0 34 0 PUMP DOSE CLEAR 1 1 SHOW 2 Update Resp B gt 52 The first command sends the Pump a Rate of 178 RPM Syringe Size of N 2 54cc and a Dose size of 1cc The second command turns on the N Pump for the 1cc Dose HK9 B PHM111 RampUpdate MG BOX BOX 178 2 54 1 0 O PUMP NULL A PHM111 PumpDose MG BOX BOX SHOW 1 Dose Resp A 2 Update Resp B gt 52 The first command sends the Pump a Rate of 178 RPM Syringe Size of b 2 54cc and a Infusion Duration Time of 0 34s The second command N turns on the Pump for the 0 34s Infusion Duration Time K10 B PHM111 RampUpdate MG BOX BOX 178 2 54 D 0 34 O PUMP NULL A PHM111 PumpDose MG BOX BOX SHOW 1 Dose Resp A 2 Update Resp B gt S2 The first commands sends the Pump a Starting Rate of 178 RPM Syringe Size of 2 54cc Ending Rate of 50 RPM and 1cc Dose The second X command turns on the Pump with the Ramp Rates provided The Pump N will calculate how long and fast to Ramp until 1cc is delivered HK11 B PHM111 RampUpdate MG BOX BOX 178 2 54 1 0 50 PUMP CALRAMP A PHM111 PumpRamp MG BOX BOX SHOW 1 Ramp Resp A 2 Update Resp B gt S2 The first command sends the Pump a Starting Rate of 178 RPM Syringe Size of 2 54cc Ending Rate of 50 RPM and a Infusion Duration Time of 0 53s The second command turns on the
Download Pdf Manuals
Related Search