Em50/Em50R Em50/Em50R
Contents
1. Direct on COM from the Connect via dropdown menu Click on the Connect icon On the main menu name the Em50 using a maximum of 8 characters op ad A aa tional 8 Select the sensors you will be using in each port as well as a measurement interval 9 If using a radio enabled Em50R set the Radio Channel 0 through and Radio Subchannel 0 through 65534 to correspond with the DataStation or Rm1 to which you will be broadcasting Em50 Em50R EmS50 Solar Quick Start Guide Introduction Thank you for purchasing an Em50 series data logger This data collection device allows you to collect and store data from up to five sensors The stored data can be downloaded using the included USB cable or via radio to a base station in case of the Em50R It is con figured using either DataTrac3 or ECH2O software Packing List Please check to make sure all listed items are present If any item is missing or damaged please contact Decagon or your local distributor e Em50 series data logger Em50 or Em50R e USB cable e Packet with 5 zip ties and 5 AA alkaline batteries e Antenna Em50R e USB flashdrive with Software driver and manual Note The DataTrac3 or ECH20 Utility software and driver is required for communication with the Em50 series data loggers The software and driver must be installed before using the Em350 see the manual for software and driver installation instructions Turning on and Configuring the E2. If using the Em50R ensure there is a good line of sight between the logger and your base station Radio signal strength can be attenuated by obstruc tions 3 If using the Em50 Solar data logger install the logger in a location that ensures the solar panel receives the maximum amount of sunlight In the northern hemisphere this typically means the data logger should face South In the southern hemisphere this typically means that the data logger should face North Downloading Data 1 Connect your computer to the Em50 using the USB cable and an available COM port Start DataTrac3 or ECH2O Utility Select Direct on COM in the Connect via dropdown menu Click on the Connect icon Select the Download icon 4 to get the data from the Em50 The next time you sleect the Download icon you will only get data collected since the a E last download You can download all data at any time under the Actions tab See manual 6 Log off the Em50 by selecting Disconnect Turning Off the Em50 To turn off the Em50 either set the measurment interval to 0 minutes or remove the batteries Note For more detailed information see the Em50 series Users Manual DECAGON DEVICES 2365 NE Hopkins Court Pullman Washington 99163 2015 Decagon Devices INc tel 509 322 2756 10782 02 10 15 support decagon com 10 Make any other desired configuration settings then click Apply 11 When first setting up the Em50 erase
3. Em50 Em50R Em50 Solar Quick Start Guide Introduction Thank you for purchasing an Em50 series data logger This data collection device allows you to collect and store data from up to five sensors The stored data can be downloaded using the included USB cable or via radio to a base station in case of the Em50R It is con figured using either DataTrac3 or ECH2O software Packing List Please check to make sure all listed items are present If any item is missing or damaged please contact Decagon or your local distributor e Em50 series data logger Em50 or Em50R e USB cable e Packet with 5 zip ties and 5 AA alkaline batteries e Antenna Em50R e USB flashdrive with Software driver and manual Note The DataTrac3 or ECH20 Utility software and driver is required for communication with the Em50 series data loggers The software and driver must be installed before using the E m50 see the manual for software and driver installation instructions Turning on and Configuring the Em50 1 Install the 5 AA Alkaline batteries included with shipment Note Em50 Solar logger comes with batteries preinstalled Remove battery pull tab to activate batteries Use only NiMH Nickel Metal Hydride batteries with the Em50 Solar logger 2 Press the silver reset button located above the batteries Connect the USB cable from your computer s USB port to the Em50 s COMM pott Launch DataTrac ECH2O Utility or ECH2O Utility Mobile software Select
4. her set the measurment interval to 0 minutes or remove the batteries Note For more detailed information see the Em50 series Users Manual DECAGON DEVICES 2365 NE Hopkins Court Pullman Washington 99163 2015 Decagon Devices Inc tel 509 322 2756 10782 02 10 15 support decagon com
5. m50 1 Install the 5 AA Alkaline batteries included with shipment Note Em50 Solar logger comes with batteries preinstalled Remove battery pull tab to activate batteries Use only NiMH Nickel Metal Hydride batteries with the Em50 Solar logger 2 Press the silver reset button located above the batteries Connect the USB cable from your computer s USB port to the Em50 s COMM pott Launch DataTrac ECH2O Utility or ECH2O Utility Mobile software Select Direct on COM from the Connect via dropdown menu Click on the Connect icon On the main menu name the Em50 using a maximum of 8 characters op ae a tional 8 Select the sensors you will be using in each port as well as a measurement interval 9 If using a radio enabled Em50R set the Radio Channel 0 through and Radio Subchannel 0 through 65534 to correspond with the DataStation or Rm1 to which you will be broadcasting 10 Make any other desired configuration settings then click Apply 11 When first setting up the Em50 erase the memory This ensures a clean data set before taking measurements 12 Log off the Em50 by clicking the Disconnect icon 13 Exit DataTrac3 or ECH2O Utility Note If you are have trouble with these steps consult the troubleshooting section of the FEim50 Em50R User s Manual Installing the Em50 1 Attach the Em50 in an upright position to a firm post or PVC pipe using the 5 zip ties or similar fasteners 2
6. the memory This ensures a clean data set before taking measurements 12 Log off the Em50 by clicking the Disconnect icon 13 Exit DataTrac3 or ECH2O Utility Note If you are have trouble with these steps consult the troubleshooting section of the FEem50 Em50R User s Manual Installing the Em50 1 Attach the Em50 in an upright position to a firm post or PVC pipe using the 5 zip ties or similar fasteners 2 If using the Em50R ensure there is a good line of sight between the logger and your base station Radio signal strength can be attenuated by obstruc tions 3 If using the Em50 Solar data logger install the logger in a location that ensures the solar panel receives the maximum amount of sunlight In the northern hemisphere this typically means the data logger should face South In the southern hemisphere this typically means that the data logger should face North Downloading Data 1 Connect your computer to the Em50 using the USB cable and an available COM port Start DataTrac3 or ECH2O Utility Select Direct on COM in the Connect via dropdown menu Click on the Connect icon Select the Download icon 4 to get the data from the Em50 The next time you sleect the Download icon you will only get data collected since the 5 oS last download You can download all data at any time under the Actions tab See manual 6 Log off the Em50 by selecting Disconnect Turning Off the Em50 To turn off the Em50 eit
Download Pdf Manuals
Related Search