User manual - Wassermann Dental
Contents
1. 2 Rinsing water hose Locate the rinsing water hose thinner hose with woven insert between the tap and the hose connector on the trimmer This connector is underneath the unit Lay it on its side to connect the hose making sure not to damage the paint Use the clamps already on the hose to connect it tightening them securely There should be a stopcock between the tap and the feed hose so the hose is not under continuous pressure when the trimmer is not being used il Tighten the hose clamps again about 2 days after installation bi The tap must be turned off at night and over the weekend e WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 6 3 Drain hose The drain hose must be laid out such that water can never back up in the trimmer This would cause the water to spray out through the grinding wheel opening Always arrange the hose in a smooth bend not kinked and with a permanent drop of at least 2 cm per metre The end of the drain hose must be above the water level of a plaster catcher If necessary shorten the hose or change the drain angle at the il The hose end must not be immersed in water i trimmer end by turning the drain hose connection In its standard configuration the drain hose connection is angled off to the right However it can also be aligned vertically to the right and this is recommended in difficult drain situations In that case use a sealing cap instead of the drain conne2. SIBILITY FOR OPERATION AND DAMAGE nnne nnn nnns 5 1 7 AUTHORIZED A 6 2 Care and Maintenance 5 6 iciette tiec Deed eset ii gan eng Oea ea Anen ei Ree E aO cCTUTSRN T ERR Yen 7 2 1 MAINTENANCE i aoa ott n AR RACE ARR DER A RAD AR AD dE A A 7 2 2 rdc rm o T NN EUREN 7 B Pee u D 8 B f re You Stall TT 8 4 1 UNPACKING 7 TRANSPORT u a ann 8 4 2 EINEN ee ee eege 9 4 3 Ee e 9 5 21 a E ee S 10 5 1 WATER REGULATION cc M 10 6 Installation naa ARIAL AAIAAU LACE 11 6 1 LOCATION T 11 6 2 RINSING WATER BEE ENEE lan e a odes D ENEE e 11 6 3 DEAD SE EE NEEN I iM CP 12 6 4 INSTALLING THE ANGLED MOUNT EE 12 6 5 SUPPORTS ege 13 TechiniGaldata ET 14 Maintenance ict iset iro ctodt uae EHE eo ETE A EEEa daoa ENE eA AAEEen E aarin Aasa EE eNi 15 8 1 SERVICING E E E ee 15 8 2 TRODBEESHOOTINGE ae ee ee 15 8 3 REPLACEMENT WHEELS co tact atn nee ner 15 8 4 ACCESSORIES AND SPARE PARTS 16 9 ETC EE 17 10 EG conformity certificate ea 18 Se WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 1 For your safety 1 1 Correct use of this product The HSS 99 plaster model trimmer is used in dental laboratories and is designed exclusively for grinding trimming plaster models To prevent damage to the trimmer and or to the blade it must be used only with plaster Otherwise the blade will quickly lose its sharpness and cutting speed 1 2 Safety symbols used in this manual Warnin
3. User manual Model HSS 99 Plaster model trimmer with solenoid valve rmm o ik I 1 d i T Wy UR Fig HSS 99 C WASSERMANN DENTAL MASCHINEN GMBH Se WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Dear customer Thank you for choosing a product from the Wassermann range Wassermann dental equipment incorporates the highest standards of quality and the latest technology In order to enjoy maximum performance and years of trouble free operation from the equipment please read this user manual carefully before you start work and operate the unit according to the recommended guidelines Please ensure that all persons operating the equipment have read and understood this user manual Keep this user manual on hand for ready reference Company address Wassermann Dental Maschinen GmbH Rudorffweg 15 17 D 21031 Hamburg Germany Tel 49 0 40 730 926 0 Fax 49 0 40 730 37 24 e mail info wassermann dental com URL http www wassermann dental com GC WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor enini sme M Y 2 UM ROR YOUR SON i eR 3 1 1 CORRECT USE OF THIS PRODUCT ne ee EX e epe eet Rae Ep Rag 3 1 2 SAFETY SYMBOLS USED IN THIS MANUALE 3 1 3 SAFETY GUIDELINES agio uoce In DM N I EM 4 1 4 EEN DEER 5 1 5 Y OUR USER E UE 5 1 6 RESPON
4. al dangers f The trimmer s rotating parts and the grinding blade are dangerous 1 5 Your user manual Configuring and operating this equipment requires precise knowledge and observance of the instructions in this user manual The equipment is designed only for its intended application 1 6 Responsibility for operation and damage The responsibility for operating the unit lies exclusively with the owner or user if the said unit is incorrectly serviced maintained or altered by persons not employed by an accredited dealer or if the unit is used in a manner contrary to its specified purpose The unit must be maintained and operated in accordance with this user manual Wassermann Dental Maschinen GmbH is not responsible for damage arising from the non observance of these instructions Guarantee and responsibility provisions contained in the sales and supply conditions of Wassermann Dental Maschinen GmbH are not extended by these instructions Se WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Product responsibility lapses if the equipment is altered by third bi parties or if non original parts are installed Use only original Wassermann replacement parts If damage occurs after a foreign wheel has been installed responsibility lies with the person who installed the said replacement wheel If diamond grinding wheels are used they will exhibit extreme wear if you grind embedding materials and metals Wassermann as
5. art 1 Hiermit wird best tigt dass die oben bezeichnete Maschine den genannten EG Richtlinien entspricht Diese Erkl rung wird ung ltig falls die Maschine ohne unsere Zustimmung ver ndert wird This is to confirm that the above mentioned machine complies with the described EC rules This declaration becomes invalid if the machine is modified without our approval Cette machine est conforme aux normes en vigueur de la Communit Europ ene Cet avis est nul et non avenant si cette machine est modifi e sans notre accord Esta m quina anteriormente mencionada cumple con los limites requeridos por el reglamento EC Ahora bien esta declaraci n quedar invalidada en caso de realizar modificaciones al aparato sin nuestra aprobaci n Hiermee wordt bevestigd dat bovengenoemde machine voldoet aan de voorgeschreven EU normen Deze verklaring verliest geldigheid als er zonder onze uitdrukkelijke toestemming wijzigen aan de machine worden aangebracht Place date Hamburg 10 April 2003 Company stamp Signed Muck L Wilfried Wassermann Managing Director e non a a oe a4 Hamburg Utt WASSERMANN DENTAL MASCHINEN WASSERMANN Dental Maschinen GmbH Rudorffweg 15 17 D 21031 Hamburg Tel 49 0 40 730 926 0 Fax 49 0 40 730 37 24 e mail info wassermann dental com Internet http www wassermann dental com
6. cation should be dry well ventilated and free of vibration An even temperature and a wooden base are desirable The trimmer must not be set up or stored out of doors il Warning The trimmer must be at room temperature before you start it d WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 5 Operation il After you switch the trimmer on wait a few seconds for the motor to come up to speed Only then can you use its full power Never push on the models so hard that the motor labours This could overload it and cause possible damage 5 1 Water regulation The water supply can be regulated using the tap or the red ball valve If you intend to set it using the ball valve make sure the tap is fully open Whichever method you use the flow of water is sufficient if the grinding wheel is close to its natural colour when grinding When grinding use light pressure only and do not move the model to the right or left Always work with fully set plaster models as wet plaster can block D drain hoses and cause smearing of the grinding wheel d WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 6 Installation 6 1 Location Because the trimmer operates exclusively with water we recommend you install it close to a tap The best place is right next to a washbasin or using the wall mount directly above the basin A further variation is to set up the trimmer on a console in the basin itself 6
7. ction 6 4 Installing the angled mount The angled mount is used for trimming very protruding teeth so as not to cut the teeth off The angled mount is attached to the HSS 99 support plate Please follow the guidelines below When working with the angled mount make sure that it has been installed correctly It should be installed as shown in the diagram below din WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Auflageblech Frontplatte Gipstrimmer 6 5 Supports The HSS 99 plaster trimmer does not need any other support than the one described in 6 4 Installing the angled mount S WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 7 Technical data Technical data Motor power 1200 Watt Operating voltage 230 Volt 50 Hz Power consumption 4 6 A Duty cycle S3 40 Speed 3000 rpm Weight 31 6 kg Dimensions Width 400 mm Height 430 mm Depth 470 mm Table 160 mm protruding il Noise emission S 70db A il We reserve the right to make technical changes The noise emission measured in a 1 metre circle around the unit and 1 6 metres high at an average 50 idling 30 average load and 20 full load was 65 dB A This was determined in accordance with DIN 45635 Part 1 s WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 8 Maintenance 8 1 Servicing For details of maintenance see 2 1 Maintenance Otherwise the trimmer does not require any special maintena
8. ctory installation 164 080 KMS grinder 164 081 GTE guide light 168 082 Template for OK to trim UK tube level 629 002 Lubricant for trimmer Spare parts 164 063 Spare diamond grinding wheel with extractor and sealing grease 1 64 026 Extractor for changing wheels 629002 Lubricating grease for trimmer WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 9 Warranty The warranty period for our equipment is 12 months If faults occur within the warranty period contact your dental depot or get in touch directly with our Service department Your plaster model trimmer should only be operated in perfect condition If faults occur which could harm operators or third parties the unit should not be used until it has been fixed This warranty does not cover damage caused by improper use external mechanical causes transport damage or interference with the unit by unauthorized persons d WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 10 EC conformity certificate in accordance with 73 23 EWG low voltage guidelines modified by 93 68 EWG and 89 336 EWG EMV guidelines and 89 392 EWG Machinery guidelines with modifications Manufacturer WASSERMANN Product description Plaster model Dental Maschinen GmbH trimmer for dental Rudorffweg 15 17 applications D 21031 Hamburg Model HSS 99 plaster trimmer 164998 Applicable EN 61010 1 1993 A2 1995 standards EN 50081 1 EN 50082 1 DIN 45635 P
9. g This is a warning of risk situations and dangers Failure to observe this warning could be life threatening These warnings must be observed lij Information This symbol draws your attention to specific features which should be noted Az WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 1 3 Safety guidelines gt gt kk p p Servicing and repairs should be carried out only by authorised specialists Before you carry out any cleaning or maintenance work disconnect the power plug and prevent the motor from restarting accidentally You should also disconnect the water line Always wear eye protection when working on grinding wheels Electric motors have dangerous electrically conducting and rotating parts when in use They can cause damage to health and property if operated incorrectly used for other than their intended purpose or inadequately serviced Only qualified specialists should carry out work on the motor Condensers must be allowed to discharge completely before you open the unit When working on the unit wear close fitting garments and roll sleeves inwards only Do not wear gloves If you have long hair wear some form of protection such as a hair net When working with the HSS 99 do not wear rings chains bracelets or similar jewellery Ga WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor il Be sure to shut off the tap at night and over the weekend 1 4 Potenti
10. mming plaster models Use this equipment only for its intended purpose 4 Before you start 4 1 Unpacking Transport Open the cartons remove the packing materials and carefully lift out the instrument and accessories Check that the accessories are correct When transporting the unit use appropriate packing materials to avoid accidental damage lij Locate the user manual and read it carefully i When unpacking it is important to identify any accidental transport damage If necessary draw up an immediate status report ch WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 4 2 Contents 164999 169030 164024 164037 320006 320017 HSS 99 with solenoid valve and ball valve Diamond grinding wheel Model mount Angled mount 1 metre water feed hose 1 metre water drain hose 4 3 Set up and storage When you set up the unit make sure that the grinding wheel is accessible and that the unit is close to the plaster cutter You will need the thinner hose 1 2 inch 13 mm with the woven insert when installing the rinsing water hose You use the thicker plastic hose 1 inch 25 mm for the drain hose When installing the drain hose make sure that the hose end hangs freely in the cutter and not beneath the surface of the water When it comes to functional safety the location of the trimmer is very important even if it is only to be stored there for a short period The lo
11. nce 8 2 Troubleshooting Fault Likely cause Likely solution Water spray at Water supply set too high Reduce water pressure at tap wheel opening or ball valve see 5 1 Water regulation Drain hose has been Make sure that the diameter of lengthened with a thinner the drain hose is 1 inch 25 4 hose mm Drain hose is kinked Make sure the hose is laid out Hose end is under the Make sure the hose ends surface of the water in the above the water surface plaster catcher The fall of the hose is insufficient cm per metre The radius of the hose is too small as straight as possible There is a tube bend in the The bend must be increased to hose causing blow back at least D 40 mm 8 3 Replacement wheels Replacement wheels are always supplied with a tube of grease for sealing the wheel chamber An extractor is also provided for removing the old wheel S WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor We strongly advise against installing a replacement wheel on top of bi an already installed wheel regardless of its origin and type i Warning If diamond wheels are used you will experience extreme wheel wear when grinding embedding materials and metals We assume no responsibility for this When using a replacement wheel follow the instructions provided for changing wheels 8 4 Accessories and spare parts Accessories Item number Description 164 030 Diamond grinding wheel for fa
12. sumes no responsibility in such cases 1 7 Authorized users The owner of the equipment must ensure that any users have been provided with the user manual and that they have read and understood its contents before operating the equipment il Ensure that this user manual is accessible at all times and has been read and understood ues WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 2 Care and maintenance 2 1 Maintenance Before you carry out any cleaning or maintenance work disconnect bi the power plug and prevent the motor from restarting accidentally Be sure to disconnect the water supply when carrying out this work Do not open the unit until the grinding wheel has come to a complete stop The HSS 99 plaster model trimmer does not require any maintenance However if you open the wheel chamber for cleaning or to change the wheel be sure to clean the sealing surfaces and coat them with a new application of water insoluble grease Top 2000 For safety reasons you should regularly check that the clamps on the water hose are tight 2 2 Care il We recommend removing any caustic traces of plaster from the outside of the unit from time to time using a damp cloth The HSS 99 does not require any other care Never clean the work plate with a cloth while the wheel is turning E WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 3 Use Application The HSS 99 trimmer is used for grinding tri
Download Pdf Manuals
Related Search