CCTV TESTER User Manual
Contents
1. Press OPEN CLOSE to control the iris Press FAR NEAR to adjust the focus manually Press WIDE TELE to zoom in out the camera lens Preset Position Set up the preset position In the PTZ control mode press S PST button then input the preset position number by the num buttons press SET to save the setup operation user can use this method to set several preset positions one by one Calling the preset position In the PTZ control mode press the C PST button then input the preset position number by the num buttons press SET to save the setup operation user can use this method to call several preset positions one by one 10 CCTV Tester User Manual 3 6 UTP cable test 1 Connect the tester to the UTP cable tester as the picture shows 2 Inthe main menu mode press num button 3 to switch to the UTP testing mode 3 Press SET to start the test UTP cable information will be displayed in the screen 4 User can estimate the UTP cable connection from the information CCTV Tester side sequence lt UTP cable test A UTP Tester side sequence are 4 X means disconnection 424 296 gt P 36 means short circuit im E 5 36 gt E 5 Press Menu button for to the main menu 11 CCTV Tester User Manual 3 7 Video generation 1 Connect the tester to the display device as the picture shows 2 Press num button 4 to switch to video gene2. Tester Autoscan Set Preset In PTZ mode press to start to set preset Address Setup PTZ ID CCTV Tester User Manual DC9 12V Power Jack UTP Cable Jack Power switch battery CCTV Tester User Manual BN CT200 NTSC PAL automatically suitable 2 5 inch LTPS LCD screen 960 x 240 resolution 1 Channel BNC Video Output 1 Channel BNC PTZ Control Communication RS485 RS422 Simplex Protocol Pelco _D P Samsung ADT YAAN HY LG Minking VIDO Videotrec or customized Supply power to camera GA K625P with an interface to supply power to the camera 6 CCTV Tester User Manual 3 Operation Introduction 3 1 Power and battery 1 The power slide switch is located at the side of the tester Turn the power slide switch to power on off 2 After the tester turning to sleeping mode turn the slide switch on again to restart it 3 The battery should be charged around 4 5 hours for full charge when charged the Charge indication LED will be on after full charging the Charge Indication LED light will be off 4 The charged battery can use for 8 hours or more 5 When the battery indicator in system menu shows 25 the states number includes 100 75 50 25 please recharge it for use 6 The tester can be used when it is being charged Please insert the battery in the correct direction 3 2 Main menu introduction Turn on the device you will see the main menu as the following shows e 1 5 ar
3. humidity or leaking gas environments Do not touch the tester with wet hands Do not shock or shake the tester while in use to avoid damage Avoid to use the tester in the places of strong magnetism or electric wave Do not expose the ports or joints to dirt or liquid Do not disassemble the tester 1 3 Precautions for battery charging and using 1 2 3 Use only original chargeable battery with the tester when charge the batteries please use the original power adapter Make sure not to disorient the polarization of batteries Do not short circuit or disassemble batteries CCTV Tester User Manual 2 Introduction 2 1 Features and functions 1 Video test The video signal and the quality of picture can be tested 2 PTZ control The unit has the basic operation test of PTZ products function includes pan tilt zoom in out Preset setting and operation auto scanning speed adjustment etc support multi protocol and baud rate communication via RS422 simplex and RS485 port RS485 protocol include Pelco D P Samsung ADT YAAN HY LG Minking Vido Videotrec Additional Protocols may be added as per customer requests Baud rate include 1200 2400 4800 9600 19200 3 UTP cable test The wiring condition disconnected short circuit and sequence of UTP cable can be tested and show in the screen clearly 4 Video signal generating It can output Black and White screen to allow technician to inspect video monitor o
4. CCTV TESTER User Manual CCTV Tester User Manual Table of Content koe MMLOMMmaOMs stoic cote N A 2 1 1 Precaution before using the tester ccccccccccccecececeeceeceeeeeeeeeeeeeeeeneaas 2 1 2 Precaution when using the tester cccccccceesessessssssseeeeeeeeeeeeeeeeeeeeeees 2 1 3 Precaution for battery charging and USING cccccsssssccecceeeeeceeeeeeeeeees 2 2 WATROGUCHIOM ee E A a 3 2l Features and UOC Oinen e eie r TASU 3 Pand ard EMS eer a E a NE 4 2 5 PUNCHON OF each Pal satese casn xiueteustondacedanle hn saceen a O eeenten 5 DA SSC CIC Ai OD ainra a E cates taut ea eae a Seton ads 6 3 Operation imroduch One utara cee eee E 7 3 POWEE and Dattely sartane TEE acme SA NE 7 32 Main Menuaintroduchon aea E E EN 7 ERE TT o E E A EE E E ace don EET E E 8 AV EOE a E E E 8 rS A A chs E E A Perr E S E E RES 9 POUP cabe TE i EN 11 DF NIGCOCENCRAUNS pa ee ee E 12 ERSA ADA UC N 13 CCTV Tester User Manual 1 Safety information 1 1 Precaution before using the tester 1 2 3 Please read the user manual before using the product Please check the input and output range of voltage or current at every input and output ports before connecting so that the Tester can not be overloaded damaged Operation environment Working temperature 30 C 70 C Humidity 30 90 Voltage DC9V 1 2 Precautions when using the tester I 2 3 4 5 6 Do not use the tester in damp
5. capacity display can t be adjusted v The device has 16 levels for the PTZ 001 means minimum speed 16 means the maximum speed vV Standby time can be set from 000 030 minutes 3 4 Video test 1 2 Connect the output terminal of video system to the video input BNC of tester turn on the tester the video can be display on the screen Connect the video output BNC of tester to the video input of other display device it can display the video signal generated by the tester 8 CCTV Tester User Manual Video out Video in 3 55 PTZ Test 1 Connection Connect the tester with the PTZ camera as the picture shows Inthe main menu press num button 2 to switch to the PTZ testing function sub menu as the following Address 001 _ PTZ1D 001 225 Video mode NULL gt Video mode PAL NTSC NULL 9 CCTV Tester User Manual 1 2 Operation Press the ADR button input the PTZ address by using num button Press the SET button to save the setup Press the MENU button to hide the hide the menu information and show a clean screen for camera image Press MENU button for 1 second to back to the main menu PTZ Control When connect the PTZ correctly the camera image will be displayed in the screen of the tester after setup the proper protocol baud rate and the ID of the PTZ user can control the PTZ as the following method Press UP DOWN LEFT RIGHT to control the movement of the PTZ
6. e five independent sub menu e Press the corresponding number button to get into the sub menu e Version number and S N can t be edited 1 System Setup gt System Information 2 PTZ Control PTZ Control function 3 UTP Test UTP Testing function 4 Video Generation gt Video generating function 5 RS485 Data Analysis gt RS485 Protocol analyzing Ver V6 18 S N 071108 gt Software Version and S N 7 CCTV Tester User Manual 3 3 System Setup 1 Press 1 to switch to the system sub menu as follows 2 3 4 5 6 PTZ Protocol Pelco D P Samsung ADT Yaan HY PROTOCOL Pelco D Minking Vido Videotrec etc COM 485 gt RS485 RS422 RATE 2400 gt Baud Rate 1200 2400 4800 9600 19200 SPEED 001 Pan and Tilt speed IDLE TIME 000 gt Idle time from last operation to auto turn off 1 30minute LANGUAGE English gt Languages BATTERY 100 Battery power status 100 75 25 0 Pies 2 Press Set button to start the set up Press number 2 and 8 PTZ direction button UP and DOWN to select the option Battery power status can be edited Press num button 4 6 PTZ direction button LEFT RIGHT to adjust the parameter Press the Clean button to save the characters in the menu will stop glitter Press the Menu button back to the main menu Notice v Battery
7. r DVR The generation signal supports PAL or NTSC do not support both meanwhile system 5 RS485 data test It can test the RS485 data sent from control device display the hexadecimal data content for engineer to analyze 6 High performance battery Built in 2000mAh high capacity Li polymer rechargeable battery and display the battery level on screen 2 2 Standard items Viens YO tty 2 3 Function of each part Data Receiving Indicator Power Indicator Data Transmission Indicator Charge Indicator CHARGE Tx Rx POWER N H 2 5 inch LTPS LCD screen 960x240 resolution Open amp Setup Close amp Clear Open iris amp Setup the functions Close Iris amp clear the setup Tele To zoom in the PTZ lens amp send the generated video signal out to the display device Menu L Long press back to main menu Ta display hide sub menu Oren cose rete MENU SET i Wide i To zoom out the PTZ lens amp recalls woe the generated video signal Far FAR L_____To adjust PTZ to far Shift Setup Buttons Shift up down right left for PTZ amp Menus amp others NEAR Near 0 9 Nub buttons To adjust PTZ to near Input number when setup preset call preset amp PTZ ID Call Preset In PTZ mode press to start to call preset CCTV
8. ration menu as follows Video Generating Video OK Notice default system 1s NTSC 3 Press Menu for 1 second to back to the main menu Press the Return TO finish the video generation operation or the Tester couldn t be switched to other function mode 12 CCTV Tester User Manual 3 8 RS485 data test 1 2 3 4 5 Connect the tester to the control device as the picture shows In the main menu press num button 5 to switch to the RS485 protocol analyzing mode as follows 485 Data analyzing Press SET to start the setup of baud rate Press UP DOWN to select the tester s baud rate make it same with the controlling device s Transfer the controlling device RS485 data to the tester the hexadecimal signal data will be displayed on the screen as follows Engineer can analyze the data to know 1f the controlling devices work with the correct protocol 485 Data Analyzing FF 01 00 02 40 00 43 FF 01 00 00 00 00 01 FF 01 00 04 40 00 45 FF 01 00 00 00 00 01 13 CCTV Tester User Manual 4 Warranty 4 1 Warranty Items 1 We provide one year warranty for all items at free of charge and we will share the freight charge with customers 2 We provide whole life repairing service for our products with proper charge Customer should carry the freight charge 4 2 Complemented items 1 The product and user manual are not assured for particular users and some special purpose of use 2 If the p
9. roducts returing for exchanging was damaged modified or miss accessory we will charge the proper cost 3 Don t offer exchanging service for special design products by customers
Download Pdf Manuals
Related Search