Home

User`s Manual (detailed) Operating Guide

1. Adjusting the zoom and focus 4 l Use the ZOOM ring to adjust the screen size ZOOM ring 2 Use the FOCUS ring to focus the picture FOCUS ring 24 Using the automatic adjustment feature Press AUTO button on the remote control Pressing this button performs the following O For a computer signal The vertical position the horizontal position and the horizontal phase will be automatically adjusted Make sure that the application window is set to its maximum size prior to attempting to use this feature A dark picture may still be incorrectly adjusted Use a bright picture when adjusting O For a video signal The video format best suited for the respective input signal will be selected automatically This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT menu E2140 The vertical position and horizontal position will be automatically set to the default O For a component video signal The vertical position and horizontal position will be automatically set to the default The horizontal phase will be automatically adjusted e The automatic adjustment operation requires approx 10 seconds Also please note that it may not function correctly with some input e When this function is performed for a video signal a certain extra such as a line may appear outside a picture e When this function is performed for a computer signal a black frame may be displayed on the edge of the screen de
2. continued on next page 36 ltem Description O O OVER SCAN V POSITION H POSITION Using the lt gt buttons adjusts the over scan ratio Small It magnifies picture Large It reduces picture e This item can be selected only for a video and component video signal For an HDMI signal this item can also be selected if either 1 or 2 applies 1 HDMI FORMAT item in the INPUT menu is set to VIDEO 2 HDMI FORMAT item in the INPUT menu is set to AUTO and the projector recognizes that it receives video signals Using the lt gt buttons adjusts the vertical position Down Up e Over adjusting the vertical position may cause noise to appear on the screen If this occurs please reset the vertical position to the default setting Pressing the RESET button when the V POSITION is selected will reset the V POSITION to the default setting e When this function is performed on a video signal the range of this adjustment depends on OVER SCAN 37 setting It is not possible to adjust when OVER SCAN is set to 10 e This function is unavailable for signal from the HDMI port Using the lt gt buttons adjusts the horizontal position Right Left e Over adjusting the horizontal position may cause noise to appear on the screen If this occurs please reset the horizontal position to the default setting Pressing the RESET button when the H POSITION is selected will reset the H POSITION to the default settin
3. 1024 x 768 60Hz 1080i 60H continued a FRAME LOCK GJ RETURN EXIT e The FRAME LOCK message on the dialog means the frame lock function is working e This item can t be selected for no signal and sync out e When the MY TEXT DISPLAY is set to ON the MY TEXT is displayed together with the input information in the INPUT_INFORMATION box 464 FACTORY RESET Selecting OK using the button performs this function By this function all the items in all of menus will collectively return to the initial setting Note that the items LAMP TIME FILTER TIME LANGUAGE FILTER MESSAGE and SECURITY settings are not reset CANCEL gt OK Be sure to set ALTITUDE after resetting all the settings L457 59 S E U R TY mM e A u ADVANCED MENU 2 SELECT PICTURE ENTER PASSWORD This projector is equipped with security functions pei From the SECURITY menu items shown in the table ease below can be performed a tela To use SECURITY menu User registration is required eran before using the security functions M EXIT Enter to the SECURITY menu COMPUTER IN 1 1024 x 768 60Hz 1 Press the button The ENTER PASSWORD box will be displayed 2 Use the A W lt gt buttons to enter the registered password EOY 5 The factory default password is as follows ENTER PASSWORD 0000 8933W 0100 This password can be changed Ebelow Move the cursor to SOEN the right side of the ENTER PASSWORD box and press ia
4. 11 Connecting with your devices continued External device Computer RS 232C i NOTE Before connecting the projector to a computer consult the computer s manual and check the compatibility of the signal level the synchronization methods and the display resolution output to the projector Some signal may need an adapter to input this projector Some computers have multiple screen display modes that may include some signals which are not supported by this projector Although the projector can display signals with resolution up to UXGA 1600x1200 the signal will be converted to the projector s panel resolution before being displayed The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical e If you connect this projector and a notebook computer you need output the display to an external monitor or output simultaneously to the internal display and an external monitor Consult the computer s manual for the setting e Depending on the input signal the automatic adjustment function of this projector may take some time and not function correctly Note that a composite sync signal or sync on green signal may confuse the automatic adjustment function of this projector 425 If the automatic adjustment function does not work correctly you may not see the dialog to set the display resolution In
5. 15 1 1 1 1 20 SANI Uo Install the projector according to the environment and manner the projector will be used in For the case of installation in a special state such as ceiling mount the specified mounting accessories LXiSpecifications in the User s Manual concise and service may be required Before installing the projector consult your dealer about your installation Arrangement Refer to tables T 1 or T 2 and figures F 1 and F 2 at the end of User s Manual concise to determine the screen size and projection distance The values shown in the table are calculated for a full size screen Screen size diagonal b Projection distance 10 from the projector s end ED ED Screen height 10 e If the projector is used at an altitude of about 1600 m 5250 feet or higher set ALTITUDE of the SERVICE item in the OPTION menu to HIGH M57 Otherwise set it to NORMAL If the projector is used with a wrong setting it may cause damage to the projector itself or the parts inside NOTE The screen position may shift after installation if the projector is suspended from the ceiling or other location due to the flexibility of the plastic projector body If readjustment is necessary consult with your dealer or service personnel continued on next page Arrangement continued WARNING P iInstall the projector where you
6. The projector will also turn off if there is no key input for about 5 minutes while the Enter PIN code box is displayed This function will activate only when the projector is started after AC power is turned off e Please do not forget your PIN code 2 Turning off the PIN LOCK 2 1 Follow the procedure in 1 1 to display the PIN LOCK on off menu 2 2 Use the A V buttons to select OFF and the Enter PIN Code box will be displayed Enter the registered PIN code to turn the PIN LOCK function off If an incorrect PIN code is input 3 times the projector will turn off 3 If you have forgotten your PIN code 3 1 While the Enter PIN code box is displayed press and hold the RESET button for three seconds or press and hold the INPUT button for 3 seconds while pressing the button on the projector The 10 digit Inquiring Code will be displayed E e If there is no key input for about 5 minutes ee ee while the Inquiring Code is displayed the 01 2345 6789 projector will turn off 3 2 Contact your dealer with the 10 digit Inquiring Code Your PIN code will be sent after your user registration information is confirmed continued on next page 62 ltem escription O O O The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten When the password is set for the MY TEXT e The MY TEXT DISPLAY menu will be unavailable which can prohibit changing the DISPLAY setting e The MY TEXT WRITING menu will be unavailable
7. The computer input signal type for COMPUTER IN1 and IN2 ports can be set 1 Use the A buttons to select the COMPUTER IN port to be set 2 Use the lt gt buttons to select EAED the computer input signal type COMPUTER IN1 COMPUTER IN 2 AUTO SYNC ON G OFF COMPUTER IN COMPUTER IN2 AUTO SYNC ON G OFF MONITOR OUT e Selecting the AUTO mode allows you to input a sync on G signal or component video signal from the port L412 e In the AUTO mode the picture may be distorted with certain input signals In such a case remove the signal connector so that no signal is received and select the SYNC ON G OFF and then reconnect the signal Set the frame lock function on off for each port 1 Use the A V buttons to select the input ports FRAME LOCK 2 Use the lt P buttons to turn the COMPUTER IN 1 COMPUTER IN 2 FRAME LOCK frame lock function on off HOM ON amp OFF e This item can be performed only on a signal with a vertical frequency of 49 to 51Hz 59 to 61 Hz e When ON is selected moving pictures are displayed more smoothly continued on next page 41 42 ltem escription O O O O O RESOLUTION The resolution for the COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector 1 In the INPUT menu select the RESOLUTION using the A V buttons and press the gt button STG The RESOLUTION menu will be displayed 1 STANDARD 1024 x 768 2 In
8. minutes at the following conditions When MyScreen or ORIGINAL is displayed as BLANK screen When start up screen is displayed continued on next page Using the A V buttons switches the mode for the blank screen The blank screen is a screen for the temporarily blanking feature 428 It is displayed by pressing the BLANK button on the remote control MyScreen amp ORIGINAL amp BLUE amp WHITE amp BLACK EE BLANK MyScreen Screen can be registered by the MyScreen item 448 ORIGINAL Screen preset as the standard screen BLUE WHITE BLACK Plain screens in each color e To avoid remaining as an afterimage the MyScreen or ORIGINAL screen will change to the AUTO BLANK screen after several 47 ltem scription O O O O O Using the A V buttons switches the mode for the start up screen The start up screen is a screen displayed when no signal or an unsuitable signal is detected MyScreen ORIGINAL OFF eee START UP MyScreen Screen can be registered by the MyScreen item Mbelow ORIGINAL Screen preset as the standard screen OFF Plain black screen e To avoid remaining as an afterimage the START UP screen will change to the AUTO BLANK screen after several minutes e When the ON is selected to the MyScreen PASSWORD item in the SECURITY menu 461 the START UP is fixed to MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and
9. 1 600m 5250feet OHIGH 1 600m 5250feet or higher RESET _ 4 RETURN ENTER _ END 18 Turning off the power 4 Press the STANDBY ON button on the projector or the remote control The message Power off will appear on the screen for about 5 seconds 2 Press the STANDBY ON button again while the message appears The projector lamp will go off and the POWER indicator will begin blinking in orange Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete 172 Do not turn the projector on for about 10 minutes or more after turning it off Also do not turn the projector off shortly after turning it on Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp NOTE Turn the power on off in right order Please power on the projector prior to the connected devices e This projector has the function that can make the projector automatically turn on off Please refer to the DIRECT POWER ON 453 and AUTO POWER OFF E2154 items of the OPTION menu Operating Adjusting the volume 1 Use the VOLUME VOLUME buttons to adjust the volume A dialog will appear on the screen to aid you in adjusting the volume If you do not do anything the dialog will automatically disappear after ten seconds VOLUME button VIDEO cower wysource CO DOC CAMERA ASPECT AUTO EACH BLANK MAGNIFY FREEZE
10. 4 LAMP indicator 172 5 TEMP indicator 072 6 POWER indicator 172 Rear panel 110 13 1 HDMI port 2 AUDIO IN R L ports 3 AUDIO OUT R L ports 4 COMPUTER IN1 port continued on next page 5 4 STANDBY ON INPUT MENU O LAMP TEMP POWER 6 5 COMPUTER IN2 MONITOR OUT port 6 CONTROL port 7 VIDEO port 8 Security slot L415 9 Security bar L15 Part names continued Remote control 1 VIDEO button 21 2 COMPUTER button 21 3 SEARCH button 22 4 STANDBY ON button 18 5 ASPECT button 0123 6 AUTO button 25 7 8 9 1 N N BLANK button 2128 MAGNIFY ON button 0427 MAGNIFY OFF button 027 0 MY SOURCE DOC CAMERA button 22 57 1 VOLUME button 20 PAGE UP button 3 PAGE DOWN button VOLUME button 120 5 MUTE button 420 6 FREEZE button 28 7 MY BUTTON 1 button 156 57 8 MY BUTTON 2 button L456 57 9 KEYSTONE button L426 0 POSITION button L25 29 21 MENU button 129 22 A W lt 4 cursor buttons 129 23 ENTER button 129 24 ESC button 429 25 RESET button 129 26 Battery cover L416 Non sen 8 8 IAN oOo om MND gt O CO OOD NY N O NOS Ommn m ee eS Sr NNN a a wA OO AB OU oau A NXS O Eee A A AAO AA es A wer Ns Ns Ns Ns N Se Se N Back of the remote control 1 12 1 14
11. MY SOURCE 57 e This function also can use for document camera Select the input port that connected the document camera Searching an input signal 4 Press SEARCH button on the remote control The projector will start to check its input ports as below in order to find any input signals When input signal is detected the projector will stop searching and display the image If no signal is found the projector will return to the state selected before the operation TERE Bi COMPUTER IN1 gt COMPUTER IN2 VIDEO HDMI i e While ON is selected for AUTO SEARCH item in OPTION menu 53 the projector will keep checking the ports in above order repeatedly till an input signal is detected 22 Selecting an aspect ratio 4 Press ASPECT button on the remote control Each time you press the button the projector switches the mode for aspect ratio in turn O For a computer signal NORMAL gt 4 3 gt 16 9 gt 16 10 o o 8933W NORMAL gt 4 3 gt 16 9 gt 16 10 gt NATIVE W oS O For an HDMI signal NORMAL gt 4 3 gt 16 9 gt 16 10 gt 14 9 fe 8933W NORMAL gt 4 3 gt 16 9 gt 16 10 gt 14 9 gt NATIVE E y O For a video signal or component video signal 4 3 gt 16 9 gt 14 9 E 8933 W 4 3 gt 16 9 gt 16 10 gt 14 9 gt NATIVE qe o O For no signal 8933W 16 10 fixed ASPECT button e ASPECT button does not work when no proper sig
12. Ps 3E 5 VOLUME ON IP ae ii ail gt OO MUTE e When X is selected for current picture input port the volume adjustment is disabled Please see AUDIO SOURCE item of AUDIO menu 0146 e Even if the projector is in the standby mode the volume is adjustable when both of the following conditions are true An option other than X is selected for STANDBY in the AUDIO SOURCE item of the AUDIO menu E146 NORMAL is selected in the STANDBY MODE item of the SETUP menu 445 Temporarily muting the sound MUTE button 4 Press MUTE button on the remote control A dialog will appear on the screen indicating that you have muted the sound To restore the sound press the MUTE VOLUME or VOLUME button Even if you do not do anything the dialog will automatically disappear after ten seconds e When X is selected for current picture input port the sound is always muted Please see AUDIO SOURCE item of AUDIO menu 4446 e C C Closed Caption is automatically activated when sound is muted and an input signal containing C C is received This function is available only when the signal is NTSC for VIDEO or 480i 60 for COMPUTER IN1 or COMPUTER IN2 and when AUTO is selected for DISPLAY in the C C menu under the SCREEN menu 2452 20 Selecting an input signal 4 Press INPUT button on the projector Each time you press the button the projector switches its input port from the current port as belo
13. Software in the projector consists of the plural number of independent software modules and there exist our copyright or and third party copyrights for each of such software modules e Be sure to read End User License Agreement for the Projector Software which is separated document DUKANE CORP AV SERVICE DEPT 2900 Dukane Drive St Charles IL 60174 800 676 2487 630 762 4032 Fax 630 584 5156 avservice dukane com www dukane com av 19
14. aa sit the gt button to display the SECURITY menu co Ala Mel e It is strongly recommended the factory default password to be E MY TEXT WRITING 4 RETURN changed as soon as possible e If an incorrect password is input the ENTER PASSWORD box will be displayed again If incorrect password is input 3 times the projector will turn off Afterwards the projector will turn off every time an incorrect password is input 3 Items shown in the table below can be performed apa If you have forgotten your password ENTER PASSWORD 1 While the ENTER PASSWORD box is displayed press and hold the 123 RESET button on the remote control for about 3 seconds or press and hold the INPUT button for 3 seconds while pressing the gt ETERS button on the projector 01 2345 6789 2 The 10 digit Inquiring Code will be displayed Contact your dealer with the 10 digit Inquiring Code Your password will be sent after your user registration information is confirmed e If there is no key input for about 55 seconds while the Inquiring Code is displayed the menu will close If necessary repeat the process from 1 ltem scription 1 Use the 4 buttons on the SECURITY menu g to select SECURITY PASSWORD CHANGE ga and press the gt button to display the ENTER NEW PASSWORD box 2 Use the A lt P buttons to enter the new password 3 Move the cursor to the right side of the ENTER NEW PASSWORD box and press the gt button SECURITY
15. and the projector recognizes that it receives video signals Using the lt gt buttons adjusts the tint Reddish Greenish e This item can be selected only for a video and component video signal e For an HDMI signal this item can also be selected if either 1 or 2 applies 1 HDMI FORMAT item in the INPUT menu is set to VIDEO 2 HDMI FORMAT item in the INPUT menu is set to AUTO and the projector recognizes that it receives video signals continued on next page 34 ltem i escription Using the lt gt buttons adjusts the sharpness Weak Strong e There may be some noise and or the screen may flicker for a moment when an adjustment is made This is not a malfunction SHARPNESS MY MEMORY This projector has 4 memories for adjustment data for all the items of the PICTURE menu Selecting a function using the A V buttons and pressing the or ENTER button performs each function len SAVE 2 SAVE 3 SAVE 4 LOAD 4 LOAD 3 LOAD 2 LOAD 1 SAVE 1 SAVE 2 SAVE 3 SAVE 4 Performing a SAVE function saves the current adjustment data into the memory linked in the number included in the function s name e Remember that the current data being stored of a memory will be lost by saving new data into the memory LOAD 1 LOAD 2 LOAD 3 LOAD 4 Performing a LOAD function loads the data from the memory linked in the number included in the function s name and adjusts the picture automa
16. buttons and ESEO press the cursor button or ENTER button to execute 9 SECURITY SERVICE the item except for the items LAMP TIME and FILTER pfii TIME Then perform it according to the following table COMPUTERIN1 1024 x 768 60Hz ltem Description Using the A V buttons turns on off the automatic signal search function ON amp OFF When the ON is selected detecting no signal automatically cycles AUTO SEARCH through input ports in the following order The search is started from the current port Then when an input is found the projector will stop searching and display the image imac ae IN1 gt COMPUTER IN2 Using the A V buttons turns on off the DIRECT POWER ON function ON amp OFF When set to the ON the lamp in projector will be automatically turned on without the usual procedure 418 only when the projector is DIRECT POWER supplied with the power after the power was cut while the lamp was on ON e This function does not work as long as the power has been supplied to the projector while the lamp is off e After turning the lamp on by the DIRECT POWER ON function if neither input nor operation is detected for about 30 minutes the projector is turned off even though the AUTO POWER OFF function 54 is disabled continued on next page 53 ltem scription O O O OO Using the A V buttons adjusts the time to count down to automatically turn the projector off Long max 99 minut
17. buttons for adjustment To close the dialog and complete this operation press KEYSTONE button again Even if you do not do anything the aguas z dialog will automatically disappear after ten seconds 5 e The menu or dialog will automatically disappear after several seconds of inactivity Pressing the KEYSTONE button again finishes the operation and closes the menu or dialog e The adjustable range of this function will vary among inputs For some input this function may not work well e When REAR CEILING or FRONT CEILING is selected for the INSTALLATION item in the SETUP menu the automatic vertical keystone correction function may not work correctly if the projector screen is slanted or tilted downwards e When the zoom adjustment is set to the TELE telephoto focus this function may be excessive This function should be used when the zoom adjustment is set to the full WIDE wide angle focus whenever possible e When the projector is inclined to near 30 degree or over this function may not work well e The display will be dark for a split second while switching the KEYSTONE but this is not a malfunction Using the magnify feature MAGNIFY 1 The picture will be magnified and the MAGNIFY dialog ON OFF button Press the MAGNIFY ON button on the remote control will appear on the screen When the MAGNIFY ON button is pressed for the first time after the ee projector is turned on the picture will
18. can access the power outlet easily If an abnormality should occur unplug the projector urgently Otherwise it could cause a fire or electric shock gt Do not subject the projector to unstable conditions If the projector falls or topples over it could result in injury or damage to the projector and the surrounding things Using a damaged projector could result in a fire and an electric shock e Do not place the projector in unstable places such as an inclined surface places subject to vibration on top of a wobbly table or cart or a surface that is smaller than the projector e Do not put the projector on its side front or rear position e Do not attach nor place anything on the projector unless otherwise specified in the manual e Do not use any mounting accessories except the accessories specified by the manufacturer Read and keep the manuals of the accessories used e For special installation such as ceiling mounting be sure to consult your dealer beforehand gt Do not install the projector near thermally conductive or flammable things Such things when heated by the projector could result in a fire and burns e Do not place the projector on a metal stand gt Do not place the projector where any oils such as cooking or machine oil are used Oil may harm the product resulting in malfunction or falling from the mounted position gt Do not place the projector in a place where it may get wet Getting the project
19. company There is a possibility that the interior portion has become heated Please turn the power off and allow the projector to cool down at least 20 minutes After the projector has sufficiently cooled down please make confirmation of the following items and then turn the power on again e Is there blockage of the air passage aperture e Is the air filter dirty e Does the peripheral temperature exceed 35 C e If the projector is used at an altitude of about 1600 m 5250 feet or higher set ALTITUDE of the SERVICE item in the OPTION menu to HIGH 57 If the projector is used with a wrong setting it may cause damage to the projector itself or the parts inside It is time to clean the air filter Please immediately turn the power off and clean or change the air filter referring to the section Cleaning and replacing the air filter After cleaning or changing the air filter please be sure to reset the filter timer After the remedy reset the power to ON There is a possibility that the interior portion has become overcooled Please use the unit within the usage temperature parameters 5 C to 35 C After the treatment reset the power to ON 73 Regarding the indicator lamps continued NOTE When the interior portion has become overheated for safety purposes the projector is automatically shut down and the indicator lamps may also be turned off In such a case disconnect the power cord and wait at least 45
20. minutes After the projector has sufficiently cooled down please make confirmation of the attachment state of the lamp and lamp cover and then turn the power on again If the projector is used at an altitude of about 1600 m 5250 feet or higher set ALTITUDE of the SERVICE item in the OPTION menu to HIGH 457 Otherwise set it to NORMAL 74 Resetting all settings When it is hard to correct some wrong settings the FACTORY RESET function of SERVICE item in OPTION menu 4159 can reset all settings except LANGUAGE FILTER TIME LAMP TIME FILTER MESSAGE and SECURITY settings and etc to the factory default Be sure to set ALTITUDE after resetting all the settings L157 Phenomena that may be easy to be mistaken for machine defects About the phenomenon confused with a machine defect check and cope with it according to the following table Cases not involving a machine defect sii The electrical power cord is not plugged in 14 Correctly connect the power cord The main power source has been interrupted during operation such as by a power outage blackout etc Please disconnect the power plug from the power outlet and allow the projector to cool down at least 10 minutes then turn the power on again Power does not come on Either there is no lamp and or lamp cover or either of these has not been properly fixed Please turn the power off and disconnect the power plug from the power outlet and allow the projector t
21. mode Installation Reset Filter time Language Advanced menu Exit PICTURE menu Brightness Contrast Gamma Color temp Color Tint Sharpness My memory IMAGE menu Aspect Over scan V position H position H phase H size Auto adjust execute INPUT menu Progressive Video nr Color space Video format Hdmi format Hdmi range Computer in Frame lock Resolution SETUP menu D Keystone Auto eco mode Eco mode Installation Standby mode Monitor out AUDIO menu 2 20008 46 Volume Speaker Audio source SCREEN menu 22055 5 47 Language Menu position Blank Auto blank Start up MyScreen MyScreen Lock Message Source name Template C c OPTION menu 000885 53 Auto search Direct power on Auto power off Lamp time Filter time My button My source Service SECURITY menu 60 Security password change MyScreen password Pin lock My text password My text display My text writing Maintenance 080500005 65 Replacing the lamp 65 Cleaning and replacing the air filter 67 Other care 02006 69 Troubleshooting 2005 70 Related messages 70 Regarding the indicator lamps 72 Resetting all settings 75 Phenomena that may be easy to be mistaken for machine defects 75 SpecificationS 79 EONO LAON Features The projector provides you with the broad use by the following features v This projector has a variety of I O
22. power consumption in the standby mode is lowered with some functional restriction as below e The RS 232C communication control is disabled except turning the projector on and changing the STANDBY MODE setting e When SAVING is selected STANDBY setting of AUDIO SOURCE 146 is invalid no signal is output from AUDIO OUT port and no sound from a built in speaker e When SAVING is selected STANDBY setting of MONITOR OUT is invalid and no signal is output from MONITOR OUT port in the standby mode While the image signal from the input port chosen in step 1 is projected the image signal from the input port selected in step 2 is output to MONITOR OUT port 1 Choose a picture input port using A V buttons Choose STANDBY to select the picture emm output in the standby mode COMPUTER OFF 2 By using lt gt buttons select veo _ COMPUTER IN 1 port or OFF to disable the MONITOR OUT port for the input port or standby mode chosen in the step 1 e If you have changed the setting of STANDBY it applies only to the current standby mode NORMAL or SAVING selected under STANDBY MODE without changing the setting of the other mode The factory settings are as follows COMPUTER IN1 for the NORMAL mode of STANDBY MODE OFF for the SAVING mode of STANDBY MODE e It is invalid if MONITOR OUT is not selected under COMPUTER IN 2 45 ANODO From the AUDIO menu items shown in the table below can be performed Select an item usin
23. prevent the internal heat level rising 68 Other care Inside of the projector In order to ensure the safe use of your projector please have it cleaned and inspected by your dealer about once every year Caring for the lens If the lens is flawed soiled or fogged it could cause deterioration of display quality Please take care of the lens being cautious of handling 4 Turn the projector off and unplug the power cord Allow the projector to cool sufficiently 2 After making sure that the projector is cool adequately lightly wipe the lens with a commercially available lens cleaning wipe Do not touch the lens directly with your hand Caring for the cabinet and remote control Incorrect care could have adverse influence such as discoloration peeling paint etc 1 Turn the projector off and unplug the power cord Allow the projector to cool sufficiently 2 After making sure that the projector is cool adequately lightly wipe with gauze or a soft cloth If the projector is extremely dirty dip soft cloth in water or a neutral cleaner diluted in water and wipe lightly after wringing well Then wipe lightly with a soft dry cloth AWARNING P gt Before caring make sure the power cord is not plugged in and then allow the projector to cool sufficiently The care in a high temperature state of the projector could cause a burn and or malfunction to the projector gt Never try to care for the inside of the proje
24. reduced e When INTELLIGENT ECO is selected the brightness of the lamp changes according to the level of the input signal The lamp becomes brighter when the input signal level is high and darker when the level is low If dark images are projected continuously the brightness of the lamp may increase to maintain its performance e When SAVER is selected you can select the time within 1 to 30 min for SAVER MODE using the gt button If the image signal level doesn t change more than the period set the lamp brightness is reduced and electric power consumption decreased If the image signal level changes or any buttons are operated the lamp will brighten again If dark images are projected continuously the brightness of the lamp may increase to maintain its performance e When AUTO ECO MODE 43 is set to ON the projector will always be set to Eco mode at start up regardless this setting Pressing the button displays the dialog for changing the INSTALLATION setting INSTALLATION Jaci be REAR DESKTOP odA Ml _ a REAR CEILING ype L TA OV i FRONT CEILING RETURN J EXIT Use the A V buttons to select the desired setting on the INSTALLATION dialog continued on next page 44 o ltem scription O O O O STANDBY MODE MONITOR OUT Using A V buttons switches the standby mode setting between NORMAL and SAVING NORMAL SAVING When SAVING is selected the
25. to display the NEW PASSWORD AGAIN box sas a PASSWORD enter the same password again a CHANGE 4 Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the gt SECURITY PASSWORD button and the NOTE NEW PASSWORD box NOTE NEW PASSWORD will be displayed for about 30 seconds please ee make note of the password during this time Pressing the ENTER button on the remote control or button on the projector will close the NOTE NEW PASSWORD box e Please do not forget your password SECURITY continued on next page 60 ltem escription O The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten 1 Turning on the MyScreen PASSWORD 1 1 Use the A V buttons on the SECURITY menu to E MyScreen PASSWORD select MyScreen PASSWORD and press the gt ON button to display the MyScreen PASSWORD on RETURN EXIT off menu 1 2 Use the A V buttons on the MyScreen F MyScreen PASSWORD PASSWORD on off menu to select ON ENTER NEW PASSWORD The ENTER NEW PASSWORD box small ee will be displayed ENTER NEW PASSWORD 1 3 Use the A W lt gt buttons to enter the box small password Move the cursor to the right side E EELS of the ENTER NEW PASSWORD box small ET TEEN and press the gt button to display the NEW PASSWORD AGAIN box enter the same PASSWORD again 1 4 Move the cursor to the right side of th
26. well SOURAN ADVANCED MENU SELECT From the SETUP menu items shown in the table a PICTURE KEYSTONE 0 below can be performed wine a le U Select an item using the A V cursor buttons and AE Ee mais press the cursor button or ENTER button to SECURITY execute the item Then perform it according to the EXT following table COMPUTER IN 1 1024 x 768 60Hz ltem escription C KEYSTONE AUTO ECO MODE Using the lt gt buttons corrects the vertical keystone distortion Shrink the bottom of the image Shrink the top of the image e The adjustable range of this function will vary among inputs For some input this function may not work well e When the zoom adjustment is set to the TELE telephoto focus this function may be excessive This function should be used when the zoom adjustment is set to the full WIDE wide angle focus whenever possible Using the A V buttons turns on off the AUTO ECO MODE ON OFF e When ON is selected the projector will always be set to Eco mode at start up regardless of the ECO MODE 144 setting An OSD message AUTO ECO MODE will be displayed for a while when the projector starts with this function activated continued on next page 43 Description ECO MODE INSTALLATION Using the A V buttons switches the ECO MODE NORMAL amp ECO INTELLIGENT ECO SAVER E a i e When the ECO is selected acoustic noise and screen brightness are
27. which can prevent the MY TEXT from being overwritten 1 Turning on the MY TEXT PASSWORD 1 1 Use the A buttons on the SECURITY Menu to ememr select the MY TEXT PASSWORD and press the aN gt button to display the MY TEXT PASSWORD on off menu 1 2 Use the A V buttons on the MY TEXT PASSWORD on off menu to select ON The EEE RAE ENTER NEW PASSWORD box small will E be displayed iik a 1 3 Use the A W lt gt buttons to enter the ENTER NEW PASSWORD password Move the cursor to the right side box small of the ENTER NEW PASSWORD box small and press the gt button to display the NEW PASSWORD AGAIN box and then enter the same password again RETURN EXIT E MY TEXT PASSWORD NEW PASSWORD AGAIN MY TEXT 1 4 Move the cursor to the right side of the NEW mE PASSWORD PASSWORD AGAIN box and press button to display the NOTE NEW PASSWORD box MY TEXT PASSWORD for about 30 seconds then please make note PHESsiiisa o00oo of the password during this time Pressing the ENTER button on the remote control or button on the projector will return to the MY TEXT PASSWORD on off menu 2 Turning off the MY TEXT PASSWORD 2 1 Follow the procedure in 1 1 to display the MY TEXT PASSWORD on off menu 2 2 Select OFF to display the ENTER ee PASSWORD box large Enter the registered EMEIS 01 2345 6789 password and the screen will return to the Pandi K MY TEXT PASSWORD on off menu ENTER PASSWORD box If an incorrect password i
28. ION SECURITY and EASY MENU EASY MENU consists of functions often used and the other menus are classified into each purpose and brought together as the ADVANCED MENU Each of these menus is operated using the same methods While the projector is displaying any menu the MENU button on the projector works as the cursor buttons The basic operations of these menus are as follows POSITION button MENU button Cursor buttons ENTER button RESI Cursor buttons ESC button ae s STANDBY ON INPUT go a AS OO lt gt VF WAH Y S ses MENU _ gt oa eS a 4 To start the MENU press the MENU button The MENU you last used EASY or ADVANCED will appear EASY MENU has priority to appear just after powered on 2 In the EASY MENU i EASY MENU SELECT 1 Use the amp cursor buttons to select an item to PCTUREMDE NORMAL operate If you want to change it to the ADVANCED BRESET pecure MENU select the ADVANCED MENU S LANGUAGE ENGLISH 2 Use the lt gt cursor buttons to operate the item SSSR PUTER IN In the ADVANCED MENU 1 Use the A F cursor buttons to select a menu SCREEN o omesso If you want to change it to the EASY MENU select ROSEE O the EASY MENU E The items in the menu appear on the right side scavu fn EXIT 2 Press the cursor button or ENTER button to move the cursor to the right side Then use the A V cursor buttons to select an item to operate a
29. OFF in the SETUP menu The lamp is approaching the end of its product lifetime Replace the lamp Either the focus and or horizontal phase settings are not properly adjusted Adjust the focus using the focus ring and or H PHASE using the menu function The lens is dirty or misty Clean the lens referring to the section Caring for the lens continued on next page TT Phenomena that may be easy to be mistaken for machine defects continued Reference Phenomenon Cases not involving a machine defect When the projector is operating in Eco mode flickering may appear on screen Set ECO MODE to NORMAL and set AUTO ECO Some kind MODE to OFF in the SETUP menu d on The OVER SCAN ratio is too big 37 such as Adjust OVER SCAN in the IMAGE menu smaller flickering or Excessive VIDEO NR 39 ses al Change the setting of VIDEO NR in the INPUT menu The FRAME LOCK function cannot work on the current input signal Set FRAME LOCK in the INPUT menu to OFF The SAVING function is working Select NORMAL for STANDBY MODE item in the SETUP menu RS 232C does not work NOTE Although bright spots or dark spots may appear on the screen this is a unique characteristic of liquid crystal displays and it does not constitute or imply a machine defect 78 Specifications Please see the Specifications in the User s Manual concise which is a book End User License Agreement for the Projector Software e
30. OGRESSIVE VIDEO NR COLOR SPACE continued on next page Using the A V buttons switches the progress mode TV FILM OFF e e This function works only for a video signal component video signal of 480i 60 or 576i 50 or 1080i 50 60 and an HDMI signal of 480i 60 or 576i 50 or 1080i 50 60 e When TV or FILM is selected the screen image will be sharp FILM adapts to the 2 3 Pull Down conversion system But these may cause a certain defect for example jagged line of the picture for a quick moving object In such a case please select OFF even though the screen image may lose sharpness Using the A V buttons switches the noise reduction mode HIGH MID LOW iE j e This function works only for a video signal component video signal of 480i 60 or 576i 50 or 1080i 50 60 and an HDMI signal of 480i 60 or 576i 50 or 1080i 50 60 Using the A V buttons switches the mode for color space AUTO RGB SMPTE240 REC709 amp REC601 E es e This item can be selected only for a computer signal component video signal or an HDMI signal e The AUTO mode automatically selects the optimum mode e The AUTO operation may not work well at some signals In such a case it might be good to select a suitable mode except AUTO 39 ltem escription O O O The video format for VIDEO port can be set 1 Use the A buttons to select the input port VIDEO FORMAT NTSC 2 Using the lt gt butt
31. ON in the left column of the menu using the V A button then press the gt button 4 Point at the LAMP TIME using the V A button then press the button A dialog will appear 5 Press the gt button to select OK on the dialog It performs resetting the lamp time NOTE Please reset the lamp time only when you have replaced the lamp for a suitable indication about the lamp 65 Replacing the lamp continued Lamp warning HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE AWARNING P The projector uses a high pressure mercury glass lamp The lamp can break with a loud bang or burn out if jolted or scratched handled while hot or worn over time Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them In addition if the bulb bursts it is possible for shards of glass to fly into the lamp housing and for gas containing mercury and dust containing fine particles of glass to escape from the projector s vent holes gt About disposal of a lamp This product contains a mercury lamp do not put itin a trash Dispose of it in accordance with environmental laws e For lamp recycling go to www lamprecycle org in the US e For product disposal consult your local government agency or www eiae org in the US or www epsc ca in Canada For more information call your dealer e If the lamp should break it will make a loud bang when it does unplug the power cord
32. Projector 8933W User s Manual detailed Operating Guide Thank you for purchasing this projector FN oyolUheidalksy MEMUEI Various symbols are used in this manual The meanings of these symbols are described below AWARNING This symbol indicates information that if ignored could possibly result in personal injury or even death due to incorrect handling 4 CAUTION This symbol indicates information that if ignored could possibly result in personal injury or physical damage due to incorrect handling NOTICE This entry notices of fear of causing trouble Q Please refer to the pages written following this symbol NOTE The information in this manual is subject to change without notice e The illustrations in this manual are for illustrative purposes They may differ slightly from your projector e The manufacturer assumes no responsibility for any errors that may appear in this manual e The reproduction transfer or copy of all or any part of this document is not permitted without express written consent Trademark acknowledgment e Mac is a registered trademark of Apple Inc e Windows DirectDraw and Direct3D are registered trademarks of Microsoft Corporation in the U S and or other countries e VESA and DDC are trademarks of the Video Electronics Standard Association e HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United S
33. RE MODE is CUSTOM Please refer to the GAMMA and COLOR TEMP M833 34 items in PICTURE menu e Lines or other noise might appear on the screen when this function is operated but it is not a malfunction continued on next page 31 Item Description Using the lt gt buttons switches the ECO MODE eCOMmOve See the ECO MODE item in SETUP menu 44 Pressing the button displays the INSTALLATION dialog INSTALLATION See the INSTALLATION item in SETUP menu 144 Performing this item resets all of the EASY MENU items except the RESET FILTER TIME and LANGUAGE A dialog is displayed for confirmation Selecting the OK using the gt button performs resetting The usage time of the air filter is shown in the menu Performing this item resets the filter time which counts usage time of the air filter PTER TIME A dialog is displayed for confirmation Selecting the OK using the gt button performs resetting See the FILTER TIME item in OPTION menu 455 Using the lt gt buttons changes the display language LANGUAGE See the LANGUAGE item in SCREEN menu 447 Press the gt or ENTER button to use the menu of PICTURE ADVANCED MENU IMAGE INPUT SETUP AUDIO SCREEN OPTION or SECURITY EXIT Press the lt or ENTER button to finish the OSD menu 32 PICMURE menu ADVANCED MENU 3 SELECT From the PICTURE menu items shown in the table Emre O CONTRAST 20 below can be performed T SETUP
34. START UP screen Display the image you want to capture before executing the following procedure Selecting this item displays a dialog titled MyScreen It will ask you if you start capturing an image from the ie current screen Please wait for the EETIO M CENTER TOs target image to be displayed and press the ENTER or INPUT button to start registration To restore the screen and return to the previous dialog press the RESET MyScreen button on the remote control Registration may take several minutes When the registration is completed the registered screen and the following message is displayed for several seconds MyScreen registration is finished If the registration failed the following message is displayed A capturing error has occurred Please try again e This function cannot be selected when the ON is selected to the MyScreen Lock item 149 e This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu 461 e This function is unavailable for signal from the HDMI port continued on next page 48 ltem escription Using the A V buttons turns on off the MyScreen lock function ON amp OFF MyScreen Lock When the ON is selected the item MyScreen is locked Use this function for protecting the current MyScreen e This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu M61 Using the A V buttons
35. The FREEZE indication will appear on the screen however the indication will not appear when the OFF is selected for the MESSAGE item in the SCREEN menu 449 and the projector will go into the FREEZE mode which the picture is frozen To exit the FREEZE mode and restore the screen to normal press the FREEZE button again e The projector automatically exits from the FREEZE mode when some control buttons are pressed e f the projector continues projecting a still image for a long time the LCD panel might possibly be burned in Do not leave the projector in the FREEZE mode for too long e Images might appear degraded when this function is operated but it is not a malfunction Temporarily blanking the screen BLANK button 4 Press BLANK button on the remote control The BLANK screen will be displayed instead of the screen of input signal Please refer to BLANK item in SCREEN menu 147 To exit from the BLANK screen and return to the input signal screen press BLANK button again e The projector automatically exits from the BLANK mode when some control buttons are pressed NOTE The sound is not connected with the BLANK screen function If necessary set the volume or mute first To display the BLANK screen and mute the sound at one time use AV MUTE function L57 28 Using the menu function This projector has the following menus PICTURE IMAGE INPUT SETUP AUDIO SCREEN OPT
36. W COLOR TEME MD Select an item using the A V cursor buttons and S SCREEN TINT press the gt cursor button or ENTER button to O SECURITY gt MYMEMORY execute the item Then perform it according to the EXIT following table CONPUTERINT 1024x 768 60H2 Item Description justs the brightness BRIGHTNESS Using the AR buttons adjusts the brightness Dark Light CONTRAST Using the lt gt buttons adjusts the contrast Weak Strong Using the A V buttons switches the gamma mode To adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the button or the ENTER button displays a dialog to aid you in adjusting the mode This function is useful when you want to change the brightness of particular tones Choose an item using the lt gt buttons and adjust the level using the A V buttons You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button Each time you press the ENTER button the pattern changes as below No pattern gt Gray scale of 9 steps t_ Ramp amp Gray scale of 15 steps The eight equalizing bars correspond to eight tone levels of the test pattern Gray scale of 9 steps except the darkest in the left end If you want to adjust the 2nd tone from left end on the test pattern use the equalizing adjustment bar 1 The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment b
37. al cables are not correctly connected 12 13 Correctly connect the connection cables The brightness is adjusted to an extremely low level 33 Adjust BRIGHTNESS to a higher level using the menu function No pictures are The computer cannot detect the projector as a Plug displayed and Play monitor Make sure that the computer can detect a Plug and Play monitor using another Plug and Play monitor The BLANK screen is displayed Press BLANK button on the remote control continued on next page 76 Phenomena that may be easy to be mistaken for machine defects continued Reference Phenomenon Cases not involving a machine defect eonenn Re O AAOS page Video screen display freezes Colors have a faded out appearance or Color tone is poor Pictures appear dark Pictures appear blurry The FREEZE function is working Press FREEZE button to restore the screen to normal Color settings are not correctly adjusted Perform picture adjustments by changing the COLOR TEMP COLOR TINT and or COLOR SPACE settings using the menu functions COLOR SPACE setting is not suitable Change the COLOR SPACE setting to AUTO RGB SMPTE240 REC709 or REC601 The brightness and or contrast are adjusted to an extremely low level Adjust BRIGHTNESS and or CONTRAST settings to a higher level using the menu function The projector is operating in Eco mode Set ECO MODE to NORMAL and set AUTO ECO MODE to
38. ar e Lines or other noise might appear on the screen when this function is operated but it is not a malfunction continued on next page 33 Using the A V buttons switches the color temperature mode To adjust CUSTOM Selecting a mode whose name includes a COLOR TE GASTON CUSTOM and then pressing the gt button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode CENTER E TEST PATTERN OFFSET adjustments change the color intensity on the whole tones of the test pattern GAIN adjustments mainly affect color intensity on the brighter tones COLOR TEMP I the test pattern Choose an item using the lt gt buttons and adjust the level using the A V buttons You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button Each time you press the ENTER button the pattern changes as below No pattern gt Gray scale of 9 steps t Ramp Gray scale of 15 steps e Lines or other noise might appear on the screen when this function is operated but it is not a malfunction Using the lt gt buttons adjusts the strength of whole color Weak Strong e This item can be selected only for a video and component video signal e For an HDMI signal this item can also be selected if either 1 or 2 applies 1 HDMI FORMAT item in the INPUT menu is set to VIDEO 2 HDMI FORMAT item in the INPUT menu is set to AUTO
39. as the security slotfor 1o the Kensington lock For details see the manual of the security tool Anti theft security bar chain or wire NOTE The security bar and slot is not comprehensive theft prevention measures It is intended to be used as supplemental theft prevention measure Remote control Installing the batteries Please insert the batteries into the remote control before using it If the remote control starts to malfunction try to replace the batteries If you will not use the remote control for long period remove the batteries from the remote control and store them in a safe place 1 Holding the hook part of the battery cover remove it 2 Align and insert the two AA batteries HITACHI MAXELL ENERGY Part No LR6 or R6P according to their plus and minus terminals as indicated in the remote control 3 _ Replace the battery cover in the direction of the arrow and snap it back into place 16 About the remote control signal The remote control works with the projector s remote sensor This projector has a remote sensor on the front The sensor senses the signal within the following range when the sensor is active 60 degrees 30 degrees to the left and right of the sensor within 3 meters about NOTE The remote control signal reflected in the screen or the like may be available If it is difficult to send the signal to the sensor directly attempt to make the signal reflect e The r
40. be zoomed by 1 5 times On the dialog triangle marks to show each direction will be displayed WAGHFY O The display magnification of the projector switches in order with every press of the MAGNIFY ON button O For computer signals or HDMI RGB signals 1 5 times gt 2 times gt 3 times gt 4 times gt 1 time Ge Ef O For video signals component video signals or HDMI Component signals 1 5 times gt 2 times gt 1 time qe While the triangles are displayed on the dialog use the A W lt gt cursor buttons to shift the magnifying area Press the MAGNIFY OFF button on the remote control to exit magnification e The MAGNIFY dialog will automatically disappear in several seconds with no operation The dialog will appear again if the MAGNIFY ON button is pressed when the dialog has automatically disappeared e The magnification is automatically disabled when the displaying signal or its display condition is changed e While the magnification is active the keystone distortion condition may vary It will be restored when the magnification is disabled e Some horizontal stripes might be visible on the image while magnification is active e This function is not available in the following cases Async signal in the range not supported is input There is no input signal 27 Temporarily freezing the screen FREEZE button 4 Press the FREEZE button on the remote control
41. cedure as described at the item 6 above 8 To finish entering text move the cursor to the OK on screen and press the gt ENTER or INPUT button To revert to the previous name without saving changes move the cursor to the CANCEL on screen and press the lt ENTER or INPUT button Using the A V cursor buttons switches the mode for the template screen Press the cursor or the ENTER button to display the selected template and press the lt cursor button to close the displayed screen The last selected template is displayed when the MY BUTTON allocated to the TEMPLATE function is pressed 57 TEST PATTERN amp DOT LINE1 amp DOT LINE2 amp DOT LINE3 2 2 MAP2 amp MAP1 CIRCLE2 CIRCLE1 amp DOT LINE4 You can turn a map upside down and scroll it horizontally when MAP1 or MAP2 is selected To invert or scroll the map display the guidance by pressing the RESET button on the remote three seconds or more when MAP1 or MAP2 appears continued on next page 51 pttem escription The C C is the function that displays a a CC transcript or dialog of the audio portion of evn ane a video files or other presentation or other gous relevant sounds It is required to have NTSC format video or 480i 60 format component video source supporting C C feature to utilize this function It may not work properly depending on equipment or signal source In this case please turn off the Closed Caption DISPLAY Selec
42. conds after the power supply connection the POWER indicator will light up in steady orange Please remember that when the DIRECT POWER ON function activated E1153 the connection of the power supply make the projector turn on AWARNING PPlease use extra caution when connecting the power cord as incorrect or faulty connections may result in fire and or electrical shock e Do not touch the power cord with a wet hand e Only use the power cord that came with the projector If it is damaged consult your dealer to get a new one Never modify the power cord e Only plug the power cord into an outlet whose voltage is matched to the power cord The power outlet should be close to the projector and easily accessible Remove the power cord for complete separation e Do not distribute the power supply to multiple devices Doing so may overload the outlet and connectors loosen the connection or result in fire electric shock or other accidents e Connect the ground terminal for the AC inlet of this unit to the ground terminal of the building using an appropriate power cord bundled NOTICE gt This product is also designed for IT power systems with a phase to phase voltage of 220 to 240 V 14 Using the security bar and slot Security slot A commercially available anti theft chain or wire can be attached to the security bar on the projector Refer to the figure to choose 12 2mm an anti theft chain or wire A Also this product h
43. ctor personally Doing is so dangerous gt Avoid wetting the projector or inserting liquids in the projector It could result in a fire an electric shock and or malfunction to the projector e Do not put anything containing water cleaners or chemicals near the projector e Do not use aerosols or sprays 4 CAUTION P Please take right care of the projector according to the following Incorrect care could cause not only an injury but adverse influence such as discoloration peeling paint etc gt Do not use cleaners or chemicals other than those specified in this manual gt Do not polish or wipe with hard objects NOTICE gt Do not directly touch the lens surface with hands 69 Mroubleshooting If an abnormal operation should occur stop using the projector immediately Otherwise if a problem occurs with the projector the following checks and measures are recommended before requesting repair If this does not resolve the problem please contact your dealer or service company They will tell you what warranty condition is applied Related messages When some message appears check and cope with it according to the following table Although these messages will be automatically disappeared around several minutes it will be reappeared every time the power is turned on There is no input signal C COMPUTER IN 1 i DEUN EREC Please confirm the signal input connection and the status of the signal source The hor
44. d by dust or other matter the internal temperature will rise which could cause malfunction or reduce the lifetime of the projector e Please be careful with the operating environment of the projector and the condition of the filter unit KEY LOCK 1 Use the A F buttons to choose the operations control CONTROL PANEL REMOTE CONTROL 2 Use the lt gt buttons to select ON or OFF Paanan CONTROL PANEL O N D O F F REMOTE CONTROL Selecting ON in Step 2 locks the buttons except STANDBY ON on the operations control selected in Step 1 Selecting OFF releases the locked buttons on the operations control selected in Step 1 e Please use this function to prevent tampering or accidental operation continued on next page 58 pttem escription REMOTE FREQ 1 Use the A button to change the projector s remote sensor frequency setting 417 1 NORMAL 2 HIGH s eee 2 Use the lt gt button to change the ZH 5 projector s remote sensor on or off ON amp OFF The factory default setting is for both 1 NORMAL and 2 HIGH to be on If the remote control does not function correctly disable either of them It s not possible to disable both options at the same time INFORMATION Selecting this item displays a dialog titled INPUT_INFORMATION It shows the information about the current input INPUT _INFORMATION T INPUT _INFORMATION T INPUT _INFORMATION S E RVI C E COMPUTER IN 1 COMPUTER IN 1 z
45. e NEW PASSWORD AGAIN box and press the gt button to display the NOTE NEW PASSWORD box for about 30 seconds please make note of the password during this time Pressing the ENTER button on the remote control or button on the MyScreen projector will return to MyScreen PASSWORD on off menu PASSWORD When a password is set for MyScreen e The MyScreen registration function and menu will be unavailable e The MyScreen Lock menu will be unavailable e The START UP setting will be locked on MyScreen and the menu will be unavailable Turning the MyScreen PASSWORD off will allow normal operation of these functions e Please do not forget your MyScreen PASSWORD 2 Turning off the MyScreen PASSWORD 2 1 Follow the procedure in 1 1 to display the MyScreen PASSWORD on off menu F MyScreen PASSWORD T 2 2 Select OFF to display the ENTER yr PASSWORD box large Enter the registered Mrgbagieene Ea password and the screen will return to the SDS MyScreen PASSWORD on off menu ENTER PASSWORD box If an incorrect PASSWORD is input the menu will ange close If necessary repeat the process from 2 1 3 If you have forgotten your password 3 1 Follow the procedure in 1 1 to display the MyScreen PASSWORD on off menu 3 2 Select OFF to display the ENTER PASSWORD box large The 10 digit Inquiring Code will be displayed inside the box 3 3 Contact your dealer with the 10 digit Inquiring Code Your password will be sent after your user reg
46. e HEE ENTER or INPUT button to select and ae ee enter characters To erase 1 character wae ASAT WRATH TE at one time press the RESET button or afbletatet folnt Litt falntotetate tele tul bebe by 2 0 1 2 3 4 5 6 7 8 9 amp press the lt and INPUT button at the BESAUUCTESRONNE DELETE I ALL CLEAR same time Also if you move the cursor cance it to DELETE or ALL CLEAR on screen RESET DELETE MY TEXT and press the ENTER or INPUT button WRITING 1 character or all characters will be erased The MY TEXT can be input up to 24 characters on each line 3 To change an already inserted character press the A V button to move the cursor to one of the first 3 lines and me use the lt gt buttons to move the cursor nosi on the character to be changed After pressing the ENTER or INPUT button the character is selected Then follow the same procedure as described at the item 2 above 4 To finish entering text move the cursor to the OK on screen and press the gt ENTER or INPUT button To revert to the previous MY TEXT without saving changes move the cursor to the CANCEL on screen and press the lt ENTER or INPUT button e The MY TEXT WRITING function is available only when the MY TEXT PASSWORD function is set to OFF E SECURITY_MY TEXT WRITING CANCEL 64 MEIMEI Replacing the lamp A lamp has finite product life Using the lamp for long periods of time could cause the pictures darker or the color to
47. e respective input signal will be selected automatically This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT menu 440 The vertical position and horizontal position will be automatically set to the default AUTO ADJUST For a component video signal exe e ie The vertical position and horizontal position will be automatically set to the default The horizontal phase will be automatically adjusted e The automatic adjustment operation requires approx 10 seconds Also please note that it may not function correctly with some input e When this function is performed for a video signal a certain extra such as a line may appear outside a picture e When this function is performed for a computer signal a black frame may be displayed on the edge of the screen depending on the computer model e The items adjusted by this function may vary when the FINE or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu 458 38 INTO Tanker ADVANCED MENU SELECT From the INPUT menu items shown in the table MAGE UIDEONR below can be performed rma Seer Select an item using the A V cursor buttons and 5 Soren E HOM RANE press the cursor button or ENTER button to Y SECURITY FRAME LOCK E EASY MENU lll RESOLUTION execute the item Then perform it according to the EXIT following table Item COMPUTER IN 1 1024 x 768 60Hz Description PR
48. ecting this word cancels the operation in the present menu and returns to the previous menu OK or YES Selecting this word executes the prepared function or shifts the menu to the next menu 30 NSC MI SIN KS 5 EASY MENU SELECT From the EASY MENU items shown in the table KEYSTONE 0 below can be performed amp PICTURE MODE NORMAL Select an item using the A V cursor buttons Then ECO MODE NORMAL INSTALLATION perform it according to the following table 4 RESET EXECUTE FILTER TIME Oh LANGUAGE ENGLISH ADVANCED MENU EXIT COMPUTER IN 1 012345678901 1024 x 768 60Hz o lem escription ASPECT Using the lt gt buttons switches the mode for aspect ratio See the ASPECT item in IMAGE menu 36 Using the lt gt buttons corrects the vertical keystone distortion CY KEYSTONE Sge the amp KEYSTONE item in SETUP menu 1143 Using the lt gt buttons switches the picture mode The picture modes are combinations of GAMMA and COLOR TEMP settings Choose a suitable mode according to the projected source M NORMAL CINEMA amp DYNAMIC amp BOARD BLACK PHOTO DAYTIME amp WHITEBOARD soarorereen d GAMMA COLOR TEMP NORMAL 1 DEFAULT 2 MID PICTURE MODE WHITEBOARD 5 DEFAULT 2 MID DAYTIME 6 DEFAULT 6 Hi BRIGHT 3 PHOTO 7 DEFAULT 7 Hi BRIGHT 4 e When the combination of GAMMA and COLOR TEMP differs from pre assigned modes above the display on the menu for the PICTU
49. emote control uses infrared light to send signals to the projector Class 1 LED so be sure to use the remote control in an area free from obstacles that could block the remote control s signal to the projector e The remote control may not work correctly if strong light such as direct sun light or light from an extremely close range such as from an inverter fluorescent lamp shines on the remote sensor of the projector Adjust the position of projector avoiding those lights Changing the frequency of remote control signal The accessory remote control has the two choices on signal frequency Mode 1 NORMAL and Mode 2 HIGH If the remote control does not function properly attempt to change the signal frequency In order to set the Mode please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds 1 Set to Mode 1 NORMAL VOLUME and RESET buttons 2 Set to Mode 2 HIGH MAGNIFY OFF and ESC buttons Please remember that the REMOTE FREQ in the SERVICE item of the OPTION menu 4159 of the projector to be controlled should be set to the same mode as the remote control 17 Turning on the power STANDBY ON button 1 Make sure that the power cord is firmly and POWER indicator correctly connected to the projector and the outlet 2 Make sure that the POWER indicator is steady orange 72 INPUT MENU STANDBY ON Cy 5 A JAN F f tame O
50. es Short min 0 minute DISABLE AUTO POWER OFF AUTO POWER OFF ENABLE DISABLE A zZ zZ Q RETURN EXIT RETURN EXIT AUTO POWER When the time is set to 0 the projector is not turned off automatically OFF When the time is set to 1 to 99 and when the passed time with no signal or an unsuitable signal reaches at the set time the projector lamp will be turned off If one of the projector s buttons or the remote control buttons is pressed or one of the commands except get commands is transmitted to the CONTROL port during the corresponding time the projector will not be turned off Please refer to the section Turning off the power 419 continued on next page 54 pS ltem scription O O O OO LAMP TIME FILTER TIME The lamp time is the usage time of the lamp counted after the last resetting It is shown in the OPTION menu Pressing the RESET button on the remote control or the gt button of the projector displays a dialog To reset the lamp time select the OK using the gt button CANCEL gt OK e Please reset the lamp time only when you have replaced the lamp for a suitable indication about the lamp e For the lamp replacement see the section Replacing the lamp 65 The filter time is the usage time of the air filter counted after the last resetting It is shown in the OPTION menu Pressing the RESET button on the remote control or the gt button of the projector disp
51. fe of this product e If the lamp breaks soon after the first time it is used it is possible that there are electrical problems elsewhere besides the lamp If this happens consult your local dealer or a service representative e Handle with care jolting or scratching could cause the lamp bulb to burst during use e Using the lamp for long periods of time could cause it dark not to light up or to burst When the pictures appear dark or when the color tone is poor please replace the lamp as soon as possible Do not use old used lamps this is a cause of breakage Cleaning and replacing the air filter Please check and clean the air filter periodically When the indicators or a message prompts you to clean the air filter comply with it as soon as possible The air filter has two kinds of filters inside Replace the filters when they are damaged or too soiled To prepare the new filters make contact with your dealer and tell the following type number Type number UX38851 Filter set When you replace the lamp please replace the air filter An air filter of specified type will come together with a replacement lamp for this projector O N E YS Turn the projector off and unplug the power cord Allow the projector to sufficiently cool down Use a vacuum cleaner on and around the filter cover Pick and pull up the filter cover knobs to take it off Use a vacuum cleaner for the filter vent of the projector Take the fine fi
52. feet or higher select HIGH Otherwise select NORMAL Note that the projector is noisier when the HIGH is selected HIGH NORMAL continued on next page 57 ps ttem scription AUTO ADJUST Using the A V buttons to select one of the mode When the DISABLE is selected the automatic adjustment feature is disabled FINE FAST amp DISABLE is FINE Finer tuning including H SIZE adjustment FAST Faster tuning setting H SIZE to prearranged data for the input signal e Depending on conditions such as input image signal cable to the projector environment around the projector etc the automatic adjustment may not work correctly In such a case please choose DISABLE to disable the automatic adjustment and make adjustment manually GHOST Adjust the settings using the A V buttons to eliminate ghosting FILTER MESSAGE Use the A V button to set the timer for notifying by the message when to replace the filter unit 100h gt lt 5000h OFF After choosing an item except OFF the message REMINDER SERVICE HRS PASSED will appear after the timer reaches the interval continued time set by this feature 71 When the OFF is chosen the message will not appear Utilize this feature to keep the air filter clean setting the suitable time according to your environment of this projector e Please take care of the filter unit periodically even if there is no message If the air filter becomes to be blocke
53. from the outlet and make sure to request a replacement lamp from your local dealer Note that shards of glass could damage the projector s internals or cause injury during handling Z so please do not try to clean the projector or replace the lamp yourself e If the lamp should break it will make a loud bang when it does ventilate the Disconnect room well and make sure not to inhale the gas or fine particles that come out the plug from the projector s vent holes and not to get them into your eyes or mouth eo e Before replacing the lamp turn the projector off and unplug the power outlet Cord then wait at least 45 minutes for the lamp to cool sufficiently Handling the lamp while hot can cause burns as well as damaging the lamp e Never unscrew except the appointed marked by an arrow screws e Do not open the lamp cover while the projector is suspended from a ceiling This is dangerous since if the lamp s bulb has broken the shards will fall out when the cover is opened In addition working in high places is dangerous so ask your local dealer to have the lamp replaced even if the bulb is not broken e Do not use the projector with the lamp cover removed At the lamp replacing make sure that the screws are screwed in firmly Loose screws could result in damage or injury e Use only the lamp of the specified type Use of a lamp that does not meet the lamp specifications for this model could cause a fire damage or shorten the li
54. g e When this function is performed on a video signal the range of this adjustment depends on OVER SCAN 137 setting It is not possible to adjust when OVER SCAN is set to 10 e This function is unavailable for signal from the HDMI port continued on next page of pttem escription Using the lt b buttons adjusts the horizontal phase to eliminate flicker Right Left H PHASE e This item can be selected only for a computer signal or a component video signal This function is unavailable for signal from the HDMI port Using the lt gt buttons adjusts the horizontal size Small Large e This item can be selected only for a computer signal This function is unavailable for signal from the HDMI port e When this adjustment is excessive the picture may not be displayed correctly In such a case please reset the adjustment by pressing the RESET button on the remote control during this operation e Images might appear degraded when this function is operated but it is not a malfunction Selecting this item performs the automatic adjustment feature For a computer signal The vertical position the horizontal position and the horizontal phase will be automatically adjusted Make sure that the application window is set to its maximum size prior to attempting to use this feature A dark picture may still be incorrectly adjusted Use a bright picture when adjusting For a video signal The video format best suited for th
55. g the A V cursor buttons and press the cursor button 2 SELECT 1 ADVANCED MENU W PICTURE IMAGE INPUT 4 SETUP d SCREEN amp OPTION SECURITY E EASY MENU a VOLUME 1 SPEAKER a AUDIO SOURCE or the ENTER button to execute the item Then EXIT perform it according to the following table COMPUTER IN 1 1024 x 768 60Hz tem escription VOLUME SPEAKER AUDIO SOURCE 46 Using the lt gt buttons adjusts the volume Low High Using the A V buttons turns on off the built in speaker ON amp OFF When OFF is selected the built in soeaker does not work While the image signal from the input port chosen in step 1 is projected the audio signal from the input port selected in step 2 is output to both the AUDIO OUT port and built in speaker of this projector However the built in soeaker does not work when SPEAKER is set to OFF 1 Choose a picture input port using the A V buttons a Choose STANDBY to select the sound COFUTERN 2 VIDEO STANDBY AUDIO SOURCE AUDIO IN output in the standby mode 2 Select an audio input port or the mute icon using the lt gt buttons The icons indicate the following No 1 AUDIO IN port X mutes the sound e Audio input from port No 2 can only be selected by HDMI input port e Even if the projector is in the standby mode cooling fans may work and make noises when the built in speaker is in operation e C C Closed Caption i
56. istration information is confirmed P MyScreen PASSWORD NOTE NEW PASSWORD 0000 continued on next page 61 pttem escription PIN LOCK is a function which prevents the projector from being used unless a registered Code is input 1 Turning on the PIN LOCK PIN LOCK 1 1 Use the A V buttons on the SECURITY menu ON to select PIN LOCK and press the button or ERE Ue ee EY the ENTER button to display the PIN LOCK on off menu PIN BOX 1 2 Use the A V buttons on the PIN LOCK on Enter PIN Code off menu to select ON and the Enter PIN gins E Code box will be displayed So l ETE 1 3 Input a 4 part PIN code using the A V lt gt EIE COMPUTER or INPUT button PIN Code again The PIN Code again box will appear Reenter the same PIN code This will complete the PIN code registration e If there is no key input for about 55 seconds while the Enter PIN Code box or the PIN Code again box is displayed the menu will close If necessary repeat the process from 1 1 Afterwards anytime the projector is restarted after AC power is turned off the Enter PIN Code box will be displayed Enter the registered PIN code The projector can be used after entering the registered PIN code If an incorrect PIN code is input the Enter PIN code box will be displayed again OROROORO ri CTTI PIN LOCK If an incorrect PIN code is input 3 times the projector will turn off Afterwards the projector will turn off every time an incorrect PIN code is input
57. izontal or vertical frequency of the input signal is COMPUTER IN 1 not within the specified range SINC 1S OUT OF RANGE Please confirm the specs for your projector or the signal 123kHz 123Hz source Specs An improper signal is input Please confirm the specs for your projector or the signal source specs COMPUTER IN 1 INVALID SCAN FREQ continued on next page 70 Related messages continued Message Description The internal temperature is rising The projector is operating in low power Please turn the power off and allow the projector to cool CHECK THE AIR ELOY down at least 20 minutes After having confirmed the following items please turn the power ON again e Is there blockage of the air passage aperture e Is the air filter dirty If so please clean or replace the air filter L467 68 e Does the peripheral temperature exceed 35 C E e If the projector is used at an altitude of about 1600 m 5250 feet or higher set ALTITUDE of the SERVICE item in the OPTION menu to HIGH 457 If the projector is used with a wrong setting it may cause damage to the projector itself or the parts inside me A note of precaution when cleaning the air filter 4000 HRS PASSED AFTER THE Please immediately turn the power off and clean or change A E the air filter referring to the Cleaning and replacing the ee fie L e air filter section of this manual After you have cleaned or RESET FILTER TIME changed the air filter
58. lays a dialog To reset the filter time select the OK using the gt button CANCEL gt OK e Please reset the filter time only when you have cleaned or replaced the air filter for a suitable indication about the air filter e For the air filter cleaning see the section Cleaning and replacing the air filter 267 continued on next page 55 ltem scription O O O OO MY BUTTON This item is to assign one of the following functions to MY BUTTON 1 2 on the remote control G6 1 Use the A buttons on the MY BUTTON menu to select a MY BUTTON 1 2 and press the or ENTER button to display the MY BUTTON setup dialog 2 Then using the A lt b buttons sets one of the following functions to the chosen button Press the ENTER or INPUT button to save the setting e COMPUTER IN1 Selects the input from COMPUTER IN1 port e COMPUTER IN2 Selects the input from COMPUTER IN2 port e HDMI Selects input from HDMI port e VIDEO Selects the input from VIDEO port e INFORMATION Displays SYSTEM_INFORMATION INPUT __ INFORMATION 459 or nothing e MY MEMORY Loads one of adjustment data stored 435 When more than one data are saved the adjustment changes every time the MY BUTTON is pressed When no data is saved in memory the dialog No saved data appears When the current adjustment is not R BUNTON Ae gt No saved data f MY BUTTON saved to memory the dialog as shown in Eenes the right a
59. lt gt Temp Fa WY Ao ss ZEE 3 Press STANDBY ON button on the projector or the remote control The projection lamp will light up and POWER indicator will begin blinking in green When the power is completely on the indicator will stop blinking and light in steady green 472 To display the picture select an input signal according to the section Selecting an input signal 221 The INITIAL SETTING Menu will be displayed by factory default upon startup Once the INITIAL SETTING Menu is set it will not appear until FACTORY RESET 159 is executed If you wish to change the settings refer to the LANGUAGE 0147 and ALTITUDE 57 menu 1 LANGUAGE Use the A W lt gt amp INITIAL SETTING buttons to select the desired language jasc and press the ENTER button of the OFRANCAIS OPYCCKI OEESTI remote control or the INPUT button of BeNi OPOLSKI Oi he the projector to execute ONORSK ODANSK Oeil ONEDERLANDS OCESKY OPORTUGUES BRA OPORTUGUES OMAGYAR OBAHASA IND OBA OROMANA OTIENG VIET 3 OSLOVENSKI OHRVATSKI OEAAHNIKA RESET _ EXIT ENTER _ NEXT 2 ALTITUDE Use the A V buttons to INITIAL SETTING select NORMAL for altitude below 1600 fatu m 5250 feet otherwise select HIGH ae ee and press the ENTER button of the an altitude of about 1 600m 5250feet or higher remote control or the INPUT button of aia eas to HIGH 1 600m 5250feet or higher the projector to execute set it to NORMAL below
60. lter out while holding the filter cover It is recommended to leave the coarse filter in the filter cover as it is Use a vacuum cleaner on both sides of the fine filter while holding it so it will not be sucked in Use a vacuum cleaner for the inside of the filter cover to clean up the coarse filter If the filters are damaged or heavily soiled replace them with new ones Place the fine filter on the coarse one Install the filter unit back into the projector continued on next page Coarse filter Fine filter 67 Cleaning and replacing the air filter continued 9 Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU 1 Press the MENU button to display a menu 2 Point at the FILTER TIME using the W A button then press the gt button A dialog will appear 3 Press the button to select OK on the dialog It performs resetting the filter time NOTE Please replace the air filter when it is damaged or heavily soiled e When you replace the projection lamp please replace the air filter An air filter of specified type will come together with a replacement lamp for this projector e Please reset the filter time only when you have cleaned or replaced the air filter for a suitable indication about the air filter e The projector may display the message such as CHECK THE AIR FLOW or turn off the projector to
61. menu is blank until a name is specified 3 Select an icon you would like to assign to the port in the SOURCE NAME dialog The name assigned to the port will also be automatically switched according to your icon selection Press the ENTER or INPUT button to determine your icon selection 4 Select a number you would like to assign to the port along with the icon You can select the number either from blank no number assigned 1 2 3 or 4 Then press the ENTER or INPUT button 5 If you would like to modify the name assigned to the port select CUSTOM NAME and press the ENTER or INPUT button SOURCE NAME continued on next page continued on next page 50 SOURCE NAME continued TEMPLATE 6 The current name will be displayed on the first line Use the A W lt gt buttons and the ENTER or INPUT button to select and enter characters To erase 1 character at one time press the RESET button or press the lt and INPUT button at the same time Also if you move the cursor to DELETE or ALL CLEAR on screen and press the ENTER or INPUT button 1 character or all characters will be erased The name can be a maximum of 16 characters 7 To change an already inserted character press the A button to move the cursor to the first line and use the lt P gt buttons to move the cursor on the character to be changed After pressing the ENTER or INPUT button the character is selected Then follow the same pro
62. nal is inputted e NORMAL mode keeps the original aspect ratio setting e The display will be dark for a split second while switching the Aspect but this is not a malfunction 23 Adjusting the projector s elevator lt Front Foot gt Using the Front elevator foot can tilt the projector in order to project at a suitable angle to the screen elevating the front side of the projector within 12 degrees The elevator foot is adjustable while pushing the elevator button 1 Holding the projector push the elevator button to loose the elevator foot 2 Release the elevator button in order to lock the elevator foot 3 If necessary the elevator foot can be manually twisted to make more precise adjustments Hold the projector when twisting the foot uut n ut eT N ARNAN i W ug aS pa aT Front foot i Rear foot lt Rear Foot gt When the place to put the projector is slightly uneven to the left or right use the Rear elevator foot to place the projector horizontally A spacer is installed on the Rear elevator foot at the time of shipment and the projector is ready for use If necessary detach the spacer and the elevator foot can be manually twisted to make more precise adjustments NOTE After the foot is adjusted it is possible to return it to the state of the shipment with a spacer It is recommended to keep the spacer and reuse it when relocating the projector
63. nd press the cursor button or ENTER button to progress The operation menu or dialog of the selected item will appear 3 Use the buttons as instructed in the OSD to operate the item COMPUTER IN 1 1024 x 768 60Hz continued on next page 29 Using the menu function continued 3 To close the MENU press the MENU button again or select EXIT and press the lt cursor button or ENTER button Even if you do not do anything the dialog will automatically disappear after about 30 seconds e f you want to move the menu position use the cursor buttons after pressing the POSITION button e Some functions cannot be performed when a certain input port is selected or when a certain input signal is displayed e When you want to reset the operation press RESET button on the remote control during the operation Note that some items ex LANGUAGE VOLUME cannot be reset e In the ADVANCED MENU when you want to return to the previous display press the lt cursor button or ESC button on the remote control Indication in OSD On Screen Display BRIGHTNESS D 24 MY MEMORY _LOAD 4 RETURN FILTER TIME TEMPORARY CONDITION A RESET ARE YOU SURE VY EXIT YOU WISH TO LOAD YES The meanings of the general words on the OSD are as follows EXIT Selecting this word finishes the OSD menu It s the same as pressing the MENU button RETURN Selecting this word returns the menu to the previous menu CANCEL or NO Sel
64. ne poor Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them Preparation of a new lamp and early replacement are recommended To prepare a new lamp make contact with your dealer and tell the lamp type number Type number 8933W 456 8933W Replacing the lamp lamp cover 3 1 Turn the projector off and unplug the power cord Allow the projector to cool for at least 45 minutes 2 Prepare a new lamp If the projector is mounted on a ceiling or if the lamp has broken also ask the dealer to replace the lamp In case of replacement by yourself follow the following procedure 3 Loosen the screw marked by arrow of the lamp cover and then slide and lift the lamp cover to the side to remove it 4 Loosen the 2 screws marked by arrow of the lamp and slowly pick up the lamp by the handle Never loosen any other screws 5 Insert the new lamp and retighten firmly the 2 6 l screws of the lamp that are loosened in the previous process to lock it in place While putting the interlocking parts of the lamp cover and the projector together slide the lamp cover back in place Then firmly fasten the screw of the lamp cover Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu 1 Press the MENU button to display a menu 2 Point at the ADVANCED MENU in the menu using the V A button then press the gt button 3 Point at the OPTI
65. o cool down at least 45 minutes After the projector has sufficiently cooled down please make confirmation of the attachment state of the lamp and lamp cover and then turn the power on again The signal cables are not correctly connected fi 12 13 Correctly connect the connection cables Signal source does not correctly work Correctly set up the signal source device by referring to the manual of the source device Neither sounds The input changeover settings are mismatched 34 22 nor pictures are Select the input signal and correct the settings outputted The BLANK function for pictures and the MUTE function for sounds are working AV MUTE may be active Refer to the item Sound does not come out and No pictures are displayed on the next page to turn off the MUTE and BLANK functions continued on next page 75 Phenomena that may be easy to be mistaken for machine defects continued Cases not involving a machine defect bali The signal cables are not correctly connected 12 13 Correctly connect the audio cables The MUTE function is working Restore the sound pressing MUTE or VOLUME Sound does button on the remote control not come out The volume is adjusted to an extremely low level Adjust the volume to a higher level using the menu function or the remote control The AUDIO SOURCE SPEAKER setting is not correct AG Correctly set the AUDIO SOURCE SPEAKER in AUDIO menu The sign
66. oes the peripheral temperature exceed 35 C If the same indication is displayed after the remedy please change the lamp referring to the section Replacing the lamp The lamp cover has not been properly fixed Blinking Please turn the power off and allow the projector to In Red cool down at least 45 minutes After the projector has Blinking sufficiently cooled down please make confirmation of In Red the attachment state of the lamp cover After performing any needed maintenance turn the power on again If the same indication is displayed after the remedy please contact your dealer or service company Blinking In Red or Lighting In Red or Lighting In Red continued on next page 72 Regarding the indicator lamps continued POWER LAMP TEMP Deseriotion indicator indicator indicator P Blinking In Red or Lighting In Red Blinking In Red or Lighting In Red Lighting In Green Lighting In Green Blinking In Red Lighting In Red Simultaneous blinking in Red Alternative blinking in Red continued on next page The cooling fan is not operating Please turn the power off and allow the projector to cool down at least 20 minutes After the projector has sufficiently cooled down please make confirmation that no foreign matter has become caught in the fan etc and then turn the power on again If the same indication is displayed after the remedy please contact your dealer or service
67. ons P e a switches the mode for video format VIDEO FORMAT AUTO NTSC PAL SECAM N PAL M PAL NTSC4 43 lt 1 e This item is performed only for video signal from the VIDEO port e The AUTO mode automatically selects the optimum mode e The AUTO operation may not work well for some signals If the picture becomes unstable e g an irregular picture lack of color please select the mode according to the input signal Using the A V cursor buttons switches the video format for an input from the HDMI port AUTO VIDEO COMPUTER es Feature HDMI FORMAT AUTO automatically sets the optimum mode VIDEO sets the suitable mode for DVD signals COMPUTER sets the suitable mode for computer signals e When the COMPUTER is selected or when the AUTO is selected and the projector recognizes that it receives computer signals the functions COLOR PICTURE menu TINT PICTURE menu and OVER SCAN IMAGE menu are unavailable Using the A V cursor buttons changes the digital range for input from the HDMI port AUTO NORMAL amp ENHANCED _ Feature AUTO automatically sets the optimum mode NORMAL sets the suitable mode for DVD signals 16 235 ENHANCED sets the suitable mode for computer signals 0 255 e If the contrast of the screen image is too strong or too weak try finding a more suitable mode HDMI RANGE continued on next page 40 ltem scription O O O O O
68. or wet or inserting liquid into the projector could cause a fire and an electric shock and damage the projector e Do not place the projector near water such as in a bathroom kitchen or poolside e Do not place the projector outdoors or by the window e Do not place anything containing liquid near the projector continued on next page Arrangement continued ACAUTION gt Place the projector in a cool place with sufficient ventilation The projector may shutdown automatically or may malfunction if its internal temperature is too high Using a damaged projector could result in a fire and an electric shock e Do not place the projector in direct sunlight or near hot objects such as heaters e Do not place the projector where the air from an air conditioner or similar unit will blow on it directly e Keep a space of 30 cm or more between a side of the projector and other objects such as walls e Do not place the projector on carpet cushions or bedding e Do not stop up block nor cover the projector s vent holes Do not place anything around the projector that could be sucked in or stuck to the projector s intake vents e Do not place the projector at places that are exposed to magnetic fields doing so can cause the cooling fans inside the projector to malfunction gt Avoid placing the projector in smoky humid or dusty place Placing the projector in such places could cause a fire an electric shock and malfunction of the p
69. or while connected to a device in operation unless that is directed in the manual of the device Otherwise it may cause malfunction in the device or projector e The function of some input ports can be selected according to your usage requirements Check the reference page indicated beside each port in the following illustration e Be careful not to mistakenly connect a connector to a wrong port Otherwise it may cause malfunction in the device or projector When connecting a connector to a port make sure that the shape of the connector fits the port Tighten the screws to connect a connector equipped with screws to a port Use the cables with straight plugs not L shaped ones as the input ports of the projector are recessed continued on next page 10 Connecting with your devices continued About Plug and Play capability e Plug and Play is a system composed of a computer its operating system and peripheral equipment i e display devices This projector is VESA DDC 2B compatible Plug and Play can be used by connecting this projector to a computer that is VESA DDC display data channel compatible Take advantage of this feature by connecting a computer cable to the COMPUTER IN1 port DDC 2B compatible Plug and Play may not work properly if any other type of connection is attempted Please use the standard drivers in your computer as this projector is a Plug and Play monitor continued on next page
70. pending on the computer model e The items adjusted by this function may vary when the FINE or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu 458 AUTO button Adjusting the position 4 Press POSITION button on the remote control when no menu is indicated The POSITION indication will appear on the screen 2 Use the A gt cursor buttons to adjust the picture position When you want to reset the operation press RESET button on the remote control during the operation To complete this operation press POSITION button again Even if you do not do anything the dialog will automatically disappear after a few seconds POSITION button e When this function is performed on a video signal some image such as an extra line may appear at outside of the picture e When this function is performed on a video signal the range of this adjustment depends on OVER SCAN in IMAGE menu M837 setting It is not possible to adjust when OVER SCAN is set to 10 e If POSITION button is pressed when a menu is indicated on screen the displayed picture does not move its position but the menu does e This function is unavailable for signal from the HDMI port 25 Correcting the keystone distortions KEYSTONE button 26 Press KEYSTONE button on the remote control A dialog will appear on the screen to aid you in correcting the distortion Use the lt gt
71. please be sure to reset the filter timer SEE MANUAL FOR FURTHER INFO 55 67 D The button operation is not available 71 Regarding the indicator lamps When operation of the LAMP TEMP and POWER indicators differs from usual check and cope with it according to the following table POWER LAMP TEMP Descriotioh indicator indicator indicator p Lighting Turned Turned The projector is in a standby state In Orange off off Please refer to the section Power on off Blinking Turned Turned The projector is warming up In Green off off Please wait Lighting Turned Turned The projector is in an on state In Green off off Ordinary operations may be performed Blinking Turned Turned The projector is cooling down In Orange off off Please wait The projector is cooling down A certain error has been detected Please wait until POWER indicator finishes blinking and then perform the proper measure using the item descriptions below Blinking discre discre In Red tionary tionary The lamp does not light and there is a possibility that interior portion has become heated Please turn the power off and allow the projector to cool down at least 20 minutes After the projector has sufficiently cooled down please make confirmation of Lighting the following items and then turn the power on again In Red e Is there blockage of the air passage aperture e Is the air filter dirty e D
72. ports that supposedly cover for any scene v This lightweight projector requires only a minimal amount of space for installation v This projector has a capability to project various picture signals onto a screen Checking the contents of package Please see the Contents of package section in the User s Manual concise which is a book Your projector should come with the items shown there Require of your dealer immediately if any items are missing NOTE Keep the original packing materials for future reshipment Be sure to use the original packing materials when moving the projector Use special caution for the lens e The projector may make a rattling sound when tilted moved or shaken since a flap to control the air flow inside of the projector has moved Be aware that this is not a failure or malfunction Part names 1 Lamp cover M65 11 The lamp unit is inside 2 Speaker R120 46 3 Filter cover L467 The air filter and intake vent are inside Elevator feet x2 L24 Elevator button 24 Remote sensor 117 Intake vents Control panel E415 0 FOCUS ring 24 1 2 3 4 ZOOM ring 124 AC AC inlet 2114 Exhaust vent 4 5 6 T 8 9 1 1 1 1 14 Rear panel 5 continued on next page Part names continued Control panel 1 STANDBY ON button L418 2 INPUT button 21 3 MENU button 29
73. ppears If you want to keep the current adjustment please press the gt button to exit Otherwise loading a data will overwrite the current adjusted condition continued on next page call saved parame ters Exit continued on next page 56 ltem escription MY BUTTON continued MY SOURCE SERVICE e PICTURE MODE Changes the PICTURE MODE 4831 e FILTER RESET Displays the filter time reset confirmation dialogue L155 e TEMPLATE Makes the template pattern selected to the TEMPLATE item 51 appear or disappear e AV MUTE Turns the picture and audio on off e RESOLUTION Turns on off the RESOLUTION dialog 142 e ECO MODE Changes the ECO MODE 44 e SAVER MODE Changes the SAVER MODE 444 ECO MODE Using A V buttons selects the picture input port to be selected with pressing the MY SOURCE DOC CAMERA button on the remote control You can use this function not only for document cameras but also computers and other equipment esta lt gt COMPUTER IN1 COMPUTER IN2 amp MA Selecting this item displays the SERVICE iit menu AUTO ADJUST FAST Select an item using the A V buttons a keok o n and press the gt button or the ENTER iromATON button on the remote control to execute g the item ALTITUDE Using the A V buttons switches the rotation speed of the cooling fans The HIGH is the mode for use at highlands etc If the projector is used at an altitude of about 1600 m 5250
74. rojector e Do not place the projector near humidifiers Especially for an ultrasonic humidifier chlorine and minerals contained in tap water are atomized and could be deposited in the projector causing image degradation or other problems NOTICE Do not place the projector in a smoking area kitchen passageway or by the window e Position the projector to prevent light from directly hitting the projector s remote sensor e Do not place the product in a place where radio interference may be caused e Check and correct the setting for ALTITUDE of SERVICE in the OPTION menu according to the usage environment 157 If the projector is used with a wrong setting it may cause damage to the projector itself or the parts inside e Keep heat sensitive things away from the projector Otherwise they may be damaged by the heat from the projector Connecting with your devices Before connecting the projector to a device consult the manual of the device to confirm that the device is suitable for connecting with this projector and prepare the required accessories such as a cable in accord with the signal of the device Consult your dealer when the required accessory did not come with the product or the accessory is damaged After making sure that the projector and the devices are turned off perform the connection according to the following instructions Refer to the figures in subsequent pages NOTE Do not turn on or off the project
75. s automatically activated when X is selected and an input signal containing C C is received This function is available only when the signal is NTSC for VIDEO or 480i 60 for COMPUTER IN1 or COMPUTER IN2 and when AUTO is selected for DISPLAY in the C C menu under the SCREEN menu 52 No 2 HDMI port SOS INI MONU From the SCREEN menu items shown in the table Ee pial PICTURE LANGUAGE ENGLISH below can be performed a A ee Select an item using the A V cursor buttons and Hoe E press the cursor button or ENTER button to E OPTION R MySereenLock OFE SECURITY MESSAGE ON execute the item Then perform it according to the EASY MENU I SOURCE NAME EXIT TEMPLATE TEST PATTERN following table TO COMPUTER IN 1 1024 x 768 60Hz ltem escription Using the A gt buttons switches the OSD On Screen Display language LANGUAGE ENGLISH amp FRANCAIS amp DEUTSCH ESPANOL shown in the LANGUAGE dialog Press the ENTER or INPUT button to save the language setting Using the A W lt gt buttons adjusts the menu position MENU POSITION To quit the operation press the MENU button on the remote control or keep no operation for about 10 seconds minutes Using the A V buttons switches the mode for the AUTO BLANK screen BLUE WHITE amp BLACK t AUTO BLANK To avoid remaining as an afterimage displayed image will change to the designated blank color screen by AUTO BLANK after several
76. s input the menu will close large If necessary repeat the process from 2 1 3 If you have forgotten your password 3 1 Follow the procedure in 1 1 to display the MY TEXT PASSWORD on off menu 3 2 Select OFF to display the ENTER PASSWORD box large The 10 digit inquiring code will be displayed inside the box 3 3 Contact your dealer with the 10 digit inquiring code Your password will be sent after your user registration information is confirmed continued on next page 63 ltem escription 1 Use the A V buttons on the SECURITY menu to emmeryy select the MY TEXT DISPLAY and press the gt or EE ENTER button to display the MY TEXT DISPLAY on off menu 2 Use the A V buttons on the MY TEXT DISPLAY on off menu to select MY TEXT on BEE SGU DISPLAY S ia When it is set ON the MY TEXT will be displayed on the START UP screen and the INPUT _ eA set INFORMATION when the INFORMATION on the 1024 x 768 60Hz SERVICE menu is chosen sh RE e This function is available only when the MY TEXT PASSWORD function is set to the OFF EXIT Q RETURN EXIT 1 Use the A F buttons on the WE SECURITY _MY TEXT WRITING SECURITY menu to select the MY _iioeiordal TEXT WRITING and press the gt button The MY TEXT WRITING dialog will be displayed aitei T HA 2 The current MY TEXT will be displayed EE a EER on the first 3 lines If not yet written the r Bg MEO lines will be blank Use the A gt buttons and th
77. such a case use an external display device You may be able to see the dialog and set an appropriate display resolution continued on next page 12 Connecting with your devices continued VCR DVD Blu ray Disc player Monitor AUDIO OUT COMPONENT L Y Cb Pb Cr Pr with an amplifier NOTE The HDMI port of this model is compatible with HDCP High band width Digital Content Protection and therefore capable of displaying a video signal from HDCP compatible DVD players or the like The HDMI supports the following signals Video signal 480i 60 480p 60 576i 50 576p 50 720p 50 60 1080i 50 60 1080p 50 60 Audio signal Format Linear PCM Sampling frequency 48kHz 44 1kHz 32kHz This projector can be connected with another equipment that has HDMI connector but with some equipment the projector may not work properly something like no video Be sure to use an HDMI cable that has the HDMI logo Use a Category 2 certified HDMI cable to input 1080p 50 60 signal to the projector When the projector is connected with a device having DVI connector use a DVI to HDMI cable to connect with the HDMI input continued on next page Connecting to a power supply 4 Put the connector of the power cord into the AC AC inlet of the projector 2 Firmly plug the power cord s plug into the outlet In a couple of se
78. t Closed Caption DISPLAY setting from following options using A V buttons AUTO ON amp OFF AUTO Closed Caption automatically displays when the volume is muted ON Closed Caption is on OFF Closed Caption is off e The caption is not displayed when the OSD menu is active e The Closed Caption is the function to display the dialogue narration and or sound effects of a television program or other C C video sources The Closed Caption availability is depending upon Closed Caption broadcaster and or content MODE Select Closed Caption MODE setting from following options using A V buttons CAPTIONS TEXT CAPTIONS Display Closed Caption TEXT Display Text data which is for additional information such as news reports or a TV program guide The information covers the entire screen Not all of the C C program has Text information CHANNEL Select Closed Caption CHANNEL from following options using A V buttons 1828384 Channel 1 primary channel language Channel 2 Channel 3 Channel 4 The channel data may vary depending on the content Some channel might be used for secondary language or empty A I IN 52 OON Taner ADVANCED MENU SELECT PICTURE AUTO SEARCH OFF From the OPTION menu items shown in the table MAGE DRECTPOIERON OFF below can be performed SETUP 7 LAMP TIME Oh D AUDIO FILTER TIME Oh Select an item using the A V cursor
79. tates and other countries e Blu ray Disc and Blu ray are trademarks of Blu ray Disc Association All other trademarks are the properties of their respective owners 430 8933W General 00 pdf na Introduction 220000000 nue 3 FeatureS 2 0000 ee eee 3 Checking the contents of package 3 Part nameS 6 0 50 bn oboe aaan 4 Setting UP is icc hd ew ew 7 Arrangement 05 f Connecting with your devices 10 Connecting to a power supply 14 Using the security bar and slot 15 Remote control 0 16 Installing the batteries 16 About the remote control signal 17 Changing the frequency of remote CONWOLSIONAL 4 6 0 2005 44 oth de wd 17 Power on off 2000005 18 Turning on the power 18 Turning off the power 19 Operating 0088n enna 20 Adjusting the volume 20 Temporarily muting the sound 20 Selecting an input signal 21 Searching an input signal 22 Selecting an aspect ratio 23 Adjusting the projector s elevator 24 Adjusting the zoom and focus 24 Using the automatic adjustment feature 2 Adjusting the position 25 Correcting the keystone distortions 26 Using the magnify feature 2 Temporarily freezing the screen 28 Temporarily blanking the screen 28 Using the menu function 29 EASY MENU 2 2000 31 Aspect Keystone Picture mode Eco
80. the RESOLUTION menu select the EUAN ERE eater resolution you wish to display using saa 4 STANDARD 1360 x 768 the A V buttons 15 STANDARD 1366 x 768 Selecting AUTO will set a resolution SOY sel ESOtes i i i RETURN appropriate to the input signal 3 Pressing the gt or ENTER button when selecting a STANDARD resolution will automatically adjust the horizontal and vertical positions clock phase and STANDARD horizontal size C COMPUTER IN 1 The INPUT_INFORMATION dialog will be displayed 4 To set a custom resolution use the A V buttons to select the CUSTOM and the RESOLUTION CUSTOM box will be displayed Set the horizontal HORZ and sci lana vertical VERT resolutions using Ny RESOLUTION_CUSTOM the A W lt gt buttons HORZ VERT This function may not support all Pee ala resolutions 5 Move the cursor to OK on screen and press the gt or ENTER button The message ARE YOU SURE YOU WISH TO CHANGE RESOLUTION appears To save the setting press the gt button The horizontal and vertical positions clock phase and horizontal size will be automatically adjusted The INPUT_INFORMATION dialog will be displayed 6 To revert back to the previous resolution without saving changes move the cursor to CANCEL on screen and press the lt or ENTER button The screen will then return to the RESOLUTION menu displaying the previous resolution e For some pictures this function may not work
81. tically depending on the data e The LOAD functions whose linked memory has no data are skipped e Remember that the current adjusted condition will be lost by loading data If you want to keep the current adjustment please save it before performing a LOAD function e There may be some noise and the screen may flicker for a moment when loading data This is not malfunction e You can perform the LOAD function using MY BUTTON Please see MY BUTTON item in OPTION menu 456 57 35 IWASE MONU ADVANCED MENU SELECT From the IMAGE menu items shown in the table PICTURE ASPECT NORMAL below can be performed a neu Postion Select an item using the A V cursor buttons and a lc P ip press the cursor button or ENTER button to ll DSa execute the item Then perform it according to the MEXT following table CONPUTERINT 1024x 768 060z ltem scription Using the A V buttons switches the mode for aspect ratio For a computer signal NORMAL 4 3 16 9 16 10 8933W NORMAL 4 3 16 9 16 10 NATIVE Oe For an HDMI signal NORMAL 4 3 amp 16 9 16 10 14 9 ee 8933W NORMAL 4 3 16 9 16 10 14 9 NATIVE a For a video signal or component video signal ASPECT 4 3 16 9 14 9 e e 8933W 4 3 16 9 16 10 14 9 NATIVE eS For no signal 8933W 16 10 fixed e The NORMAL mode keeps the original aspect ratio of the signal
82. turns on off the message function ON OFF When the ON is selected the following message function works AUTO IN PROGRESS while automatically adjusting NO INPUT IS DETECTED SYNC IS OUT OF RANGE INVALID SCAN FREQ NOT AVAILABLE Searching while searching for the input Detecting while an input signal is detected MESSAGE AUTO ECO MODE while starting up with AUTO ECO MODE The indication of the input signal displayed by changing The indication of the aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the MY MEMORY displayed by changing The indication of FREEZE and II while freezing the screen by pressing the FREEZE button The indication of the TEMPLATE displayed by changing The indication of the ECO MODE displayed by changing e When the OFF is selected please remember if the picture is frozen Do not mistake freezing for a malfunction 1128 continued on next page 49 ltem escription O Each input port for this projector can have a name applied to it 1 Use the A buttons on the SCREEN menu to select SOURCE NAME and press the gt or ENTER button The SOURCE NAME menu will be displayed 2 Use the A buttons on the SOURCE SOURCE NAE NAME menu to select the port to be aS named and press the button The a gt 6 myne SOURCE NAME dialog will be displayed Soe Right side of the
83. w K COMPUTER IN1 gt COMPUTER IN2 VIDEO HDMI el e While ON is selected for AUTO SEARCH item in OPTION menu M53 the projector will keep checking the ports in above order repeatedly till an input signal is detected 4 Press COMPUTER button on the remote control COMPU TE Ll Each time you press the button the projector switches its input port from the current port as below COMPUTER IN1 gt COMPUTER IN2 Fo RIR OFF DOWN dl vevertan TTON a MITE e m MYBU T e While ON is selected for AUTO SEARCH item in OPTION menu the projector will keep checking every port sequentially till an input signal is detected 2153 If COMPUTER button is pressed when VIDEO or HDMI port is selected the projector will check COMPUTER IN1 port first VIDE 4 Press VIDEO button on the remote control e oauan Each time you press the button the projector switches its input port from the current port as below P HDMI gt VIDEO 7 e While ON is selected for AUTO SEARCH item in OPTION menu the projector will keep checking every port sequentially till an input signal is detected E4153 If VIDEO button is pressed when COMPUTER IN1 or COMPUTER IN2 port is selected the projector will check HDMI port first 21 Selecting an input signal continued q _ Press the MY SOURCE DOC CAMERA button on DOC CAMERA button the remote control The input signal will be changed into the signal you set as

User`s Manual (detailed) Operating Guide

Contents

Download Pdf Manuals

Related Search

Related Contents