View Owner`s Manual - Hot Spot CB Radio Shop
Contents
1. be lengthed 3 The whip is easily cut by filing a notch all the way around and breaking the piece off with pliers NOTE THE PROPER SETTING IS ACHIEVED WHEN THE SWR IS 1 5 OR BELOW AND WHEN IT HAS THE SAME READING FOR CHANNELS BAND A Ch 1 AND BAND F Ch40 If you are having difficulties in adjusting your antenna check the following A All doors must be closed when adjusting the antenna B Make sure the antenna base is grounded C Check your coaxial cable routing it may be pinched when routed into the car D Try a different location on your car keeping in mind the radiation pattern you wish Is the antenna perfectly vertical F Try a different location in your neighborhood Stay away from large metal objects when adjusting metal telephone or light posts fences etc NOTE The transceiver will operate into an SWR of 2 to 1 indefinitely and sustain an SWR of 20 1 for a maximum of 5 minutes at rated operating conditions EXTERNAL SPEAKER The external speaker jack EXT SPK on the rear panel is used for remote receiver monitoring The external speaker should have 8 ohms impedance and be able to handle at least 4 watts When the external speaker is plugged in the internal speaker is disconnected Operation CONTROL FUNCTIONS There are thirteen controls and three indicators on the front panel of your transceiver DX 55HP FRONT PANEL 1 OFF ON VOLUME inner dual concentric Turn clock2. receptacle body Note the location of the screw clearance hole in the plug housing with respect to the threaded hole in the pin receptacle body When the housing is completely threaded into the pin receptacle body a final fraction of a turn either clockwise or counterclockwise may be required to align the screw hole with the threaded hole in the pin receptacle body When these are aligned the retaining screw is then screwed into the place to secure the housing to the pin receptacle body The two cable clamp retainer screws should now be tightened to secure the housing to the microphone cord If the cutting directions have been carefully followed the cable clamp should secure to the insulating jacket of the microphone cable Upon completion of the microphone plug wiring connect and secure the microphone plug in the transceiver 15 MEMO 16 17 WARRANTY This radio is covered by a two year Limited parts and labor warranty Limited means that we will repair problems caused by factory defects or normal use at no charge This warranty does not cover any modifications made to the radio and any modification may void the warranty completely Before returning a radio to us for warranty service please call our Service Department for a Repair Authorization Number RAN This RAN must be written below your return address on the outside of the shipping box Boxes which arrive without an RAN will be refused and the shippi
3. Galaxy DX S5HP F DISPLAY FM OFF R B 10KHz 3 A 7 6 ne O O 4 H PA OFF OFF OFF Cady DX 55HP 10 Meter AM FM Mobile Transceiver Built in Frequency Counter with Roger Beep OWNER S MANUAL Printed In Malaysia A412308BTA TABLE OF CONTENTS Specifications Page SPCCHICATION soeces mirate etl kas Vea ke ates 2 GENERAL Channels 40 CH Installation Frequency Range 28 065 to 28 505 MHz Frequency Control Phase Lock Loop PLL synthesizer Locations 2 0i 64 eee eee edad EEE EFESE 4 Frequency Tolerance 0 005 Frequency Stability 0 001 Mounting the Radio 0 0 0 cece een ees 4 Operating Temperature 30 C to 50 C Range Ignition Noise Interference 005 5 Microphone Plug in dynamic with push to talk switch and coiled cord Antenna 2 cerere ceed ae evade eee ae He Pee es 5 Input Voltage 13 8V DC nominal 15 9V max 11 7V min Positive or negative ground Tuning the Antenna for Optimum SWR 6 Transmit AM full mod 4 5A Receiver Squelched 0 3A External Speaker 0 00000 e eee eeees 7 Maximum Audio output 0 7A Size 2 3 8 H x 7 7 8 W x 9 1 4 D Operation Weight 5 bs Antenna Connector UHF SO239 Control Functions 0 0 0000 e eee eee 8 Meter 2 in 1 Illuminated indicates relative output power and received signal strength ASHrontPanel ects 4 ceetaite bs ee aiaes Aad eg hs 8 TRANSMITTER Bs Rear Pantie 3 s si c05 coh tt dee ne rena ted oe 11 Pow
4. e the accessory contact on most ignition switches by tracing the power wire from the AM broadcast receiver in the car Connect the black lead to ground This is usually the chassis of the car Any convenient location with good electrical contact remove paint may be used Mount the microphone bracket on the right side of the transceiver or near the transceiver using two screws supplied When mounting in an automobile place the bracket under the dash so the microphone is readily accessible IGNITION NOISE INTERFERENCE Use of a mobile receiver at low signal levels is normally limited by the presence of electrical noise The primary source of noise in automobile installations is from the generator and ignition system in the vehicle Under most operating conditions when signal level is adequate the background noise does not present a serious problem Also when extremely low level signals are being received the transceiver may be operated with vehicle engine turned off The unit requires very little current and therefore will not significantly discharge the vehicle battery Even though the transceiver has ANL and NB controls in same installations ignition interference may be high enough to make good communications impossible The electrical noise may come from several sources Many possibilities exist and variations between vehicles require different solutions to reduce the noise ANTENNA A vertically polarized quarter wavelength whip an
5. er output AM FM HIGH 10 watts LOW 2 watts Modulation High and low level Class B Amplitude Press To Talk Microphone 005 12 Modulation AM Variable capacitance Frequency Modulation FM Operating Procedure to Receive 12 Spurious Emissions 60 dB Frequency Response AM and FM 450 to 2500 Hz Operating Procedure to Transmit 12 Output Impedance 50 ohms unbalanced Output Indicators Meter shows relative RF output power Alternate Microphones and Installation 13 Transmit LED glows red when transmitter is in operation RECEIVER Sensitivity Selectivity Image Rejection IF Frequency Adjacent Channel Rejection RF Gain Control Automatic Gain Control AGC Squelch ANL Noise Blanker Audio Output Power Frequency Response Built in Speaker External Speaker Not Supplied AM 1 0 uV for 10 dB S N N at greater than 1 2 watt of audio output FM 1 0 uV for 20 dB S N N at greater than 2 watt of audio output AM FM 6 dB 3 KHz 50 dB 9 KHz More than 65 dB AM FM 10 695 MHz 1 IF 455 KHz 2 IF 60 dB AM 45 dB adjustable for optimum signal reception Less than 10 dB change in audio output for inputs from 10 to 100 000 microvolts Adjustable threshold less than 0 5 uV Switchable RF type 4 watts into 8 ohms 300 to 2800 Hz 8 ohms round 8 ohms disables internal speaker when connected Installation LOCATION Plan the location of the t
6. es If a vise or clamping tool is available it should be used to hold the pin receptacle body during the soldering operation so that both hands are free to perform the soldering If a vise or clamping tool is not available the pin receptacle body can be held in a stationary position by inserting it into the microphone jack of the front panel The numbers of the pins of the microphone plug are shown in Fig 3 as viewed from the back of the plug Before soldering the wire to the pins pre tin the wire receptacle of each pin of the plug 14 Fig 3 Microphone plug pin numbers viewed from rear of pin receptacle Be sure that the housing and the knurled ring of Fig 2 are pushed back onto the microphone cable before starting to solder If the washer is not captive to the pin receptacle body make sure that it is placed on the threaded portion of the pin receptacle body before soldering If the microphone jack is used to hold the pin receptacle during the soldering operation best results are obtained when the connections to pins and 3 are made first and then the connections to pins 2 and 4 Use a minimum amount of solder and be careful to prevent excessive solder accumulation on pins which could cause a short between the pin and the microphone plug housing When all soldering connections to the pins of the microphone plug are complete push the knurled ring and the housing forward and screw the housing onto the threaded portion of the pin
7. h the sign 10KHz FREQUENCY SHIFT SWITCH When switch is pressed the frequency is shifted 1OKHz up On following channels A channel can be used by setting this switch to 10KHz position Normal 3 7 11 15 19 15 FREQUENCY COUNTER This frequency counter LEDS indicate the selected transmit and receive frequency you are operating on 16 CHANNEL INDICATOR The mumbered LEDS indicate the selected channel you are on 10 10KHz 3A 7A 11A 15A 19A REAR PANEL a O lil D PA SP EXT SP SF Bae MADE IN MALAYSIA 17 POWER Accepts 13 8V DC power cable with built in fuse 6 amp to be connected 18 EXT SP Accepts 4 to 8 ohms 5 watt external speaker to be connected When external speaker is connected to this jack the built in speaker is automatically disconnected 19 PA SP Used to connect a PA speaker 8 ohm 4W for PA operation Before operating PA you must first connect a PA speaker to this jack 20 ANTENNA Accepts 50 ohm coaxial cable with a type PL 259 plug to be connected 11 PRESS TO TALK MICROPHONE The receiver and transmitter are controlled by the press to talk switch on the microphone Press the switch and the transmitter is activated release switch to receive When transmitting hold the microphone two inches from the mouth and speak clearly in a normal voice The radios come complete with low impedance 500 ohm dynamic microphone For installation instruction on other microphone
8. ise two of the leads The fourth lead is for receive control and the third is for transmit control The microphone should provide the functions shown in schematic below 4 WIRE MIC CABLE Pin Number Mic Cable Lead 1 Audio shield 2 Audio Lead 3 Transmit control 4 Receive Control Fig 1 Your transceiver microphone schematic If the microphone to be used is provided with pre cut leads they must be revised as follows 1 Cut leads so that they extend 7 16 beyond the plastic insulating jacket of the microphone cable 2 All leads should be cut to the same length Strip the ends of each wire 1 8 and tin the exposed wire Before beginning the actual wiring read carefully the circuit and wiring information provided with the microphone you select Use the minimum head required in soldering the connections Keep the exposed wire lengths to a minimum to avoid shorting when the microphone plug is reassembled 13 oO YS KNURLED RING BS HOUSING s PIN RECEPTACLE ra RETAINING SCREW CABLE CLAMP RETAINER SGREW 2 A MICROPHONE CONNECTOR ASSEMBLY B MICROPHONE CONNECTOR DISASSEMBLED FOR WIRING Fig 2 Microphone plug wiring Remove the retaining screw Unscrew the housing from the pin receptacle body Loosen the two cable clamp retainer screws Feed the microphone cable through the housing knurled ring and washer as shown Fig 2 The wires must now be soldered to the pins as indicated in the above wiring tabl
9. ncentric This switch is used to select transmitting power BAND SELECTOR This switch selects A B C D E or F band of operation CLARIFIER Allows variation of the receiver operating frequencies above and below the assigned frequency It may be used to optimize AM FM signals as described in the Operating Procedure paragraphs operates both TX RX CHANNEL SELECTOR This switch selects any one of the forty channels desired The selected channel appears on the LED readout directly above the Channel Selector knob METER This meter indicates received signal strength and transmitter RF output power MODE FM AM PA SWITCH This switch is used to select PA FM AM mode of operation The AM or FM mode is normally selected but when you set to PA position the transceiver acts as a public address amplifier Before operating PA you must first connect an external PA speaker 8 ohm more than 2W to the PA Speaker jack on the unit rear panel F DISPLAY OFF NB OFF SWITCH When the switch is placed in the NB position the RF noise blanker is activated The RF noise blanker is very effective for repetitive impulse noise such as ignition interference If you wish to turn off the frequency display only set switch to NB position ROGER BEEP SWITCH When this switch is placed in the ROGER BEEP position your radio automatically transmits the audio sign at the end of your transmission The listener can note easily your transmission is over throug
10. ng company will return the unopened box to you Be sure to have a pen and paper ready along with the serial number of your radio before calling We will give you the RAN and our shipping address over the phone The telephone number of the Service Department is 760 480 8800 and we suggest calling between 10 00 AM and 4 00 PM Pacific Time Please include a note with a detailed description of the symptoms This is important because it will help the technician who works on your radio to locate your problem Intermittent problems are easily overlooked so be sure to give as much detail as possible in your note Also please include your daytime telephone number in case our technicians have any additional questions Do not send your power cord or microphone unless we ask for these items during our telephone conversation You are responsible for getting the radio safely to us We suggest using United Parcel Service You must pay to ship the radio to us and we will pay to ship the radio back to you Since we use UPS and they do not ship to Post Offices boxes please provide us with a street address for the return of your radio We will repair and return your radio as soon as we can We appreciate your choosing a Galaxy radio and we want you to be on the air as much as possible Be sure to visit our web site at www GalaxyRadios com 18
11. ransceiver and microphone bracket before starting the installation Select a location that is convenient for operation and does not interfere with the driver or passengers in the vehicles In automobiles the transceiver is usually nounted below the dash panel with the microphone bracket beside it MOUNTING THE RADIO Your transceiver is supplied with a universal mounting bracket When mounting the bracket and radio to your car make sure it is mechanically strong Also provide a good electrical connection to the chassis of the vehicle Proceed as follows to mount the transceiver 1 After you have determined the most convenient location in your vehicle hold the transceiver with mounting bracket in the exact location desired If nothing will interfere with mounting it in the desired position remove the mounting bolts Before drilling the holes make sure nothing will interfere with the installation of the mounting bolts Connect the antenna cable plug to the standard receptacle on the rear panel Most antennas are terminated with a type PL 259 plug and mate with the receptacle Connect the red DC power input wire with the fuse to 13 8V DC This wire extends from the rear panel In automobile installation 13 8V DC is usually obtained from the accessory contact on the ignition switch This prevents the set being left on accidentally when the driver leaves the car and also permits operating the unit without the engine running Locat
12. s see next section ALTERNATE MICROPHONES AND INSTALLATION OPERATING PROCEDURE TO RECEIVE 1 Be sure that power source microphone and antenna are connected to the proper connectors before going to the next step Turn unit on by tuning VOL control clockwise on your transceiver Set the VOLUME for a comfortable listening level Set the MODE switch to the desire mode Listen to the background noise from the speaker Turn the SQUELCH control slowly clockwise until the noise JUST disappears no signal should be present Leave the control at this setting The SQUELCH is now properly adjusted The receive will remain quiet until a signal is actually received Do not advance the control too far or some of the weaker signals will not be heard 6 Set CHANNEL selector switch to the desired channel 7 Set the RF gain control fully clockwise for maximum RF gain AP YN OPERATING PROCEDURE TO TRANSMIT 1 Select the desired channel of transmission 2 Set the MIC GAIN control fully clockwise 3 Ifthe channel is clear depress the push to talk switch on the microphone and speak in a normal voice 12 ALTERNATE MICROPHONES AND INSTALLATION For best results the user should select a low impedance dynamic type microphone or a transistorized microphone Transistorized type microphones have a low output impedance characteristic The microphones must be provided with a four lead cable The audio conductor and its shielded lead compr
13. stable antennas Because the antenna length is directly related to the channel frequency it must be tuned to resonate optimally on all channels of the transceiver Channel requires a longer antenna than Channel 40 because it is lower in frequency Due to the various methods of adjusting antennas for proper SWR we have chosen what we think is the optimum method A Antennas with adjustment screws set screws 1 Start with the antenna extended and tightens the set screw lightly enough so that the antenna can be lightly tapped with your finger for easy adjustment 2 Set your transceiver to Channel 21 on Band C or Band D Press the PTT push to talk switch and tap the antenna making it shorter The SWR meter will show a lower reading each time the antenna is tapped By continuing to shorten the antenna you will notice the SWR reading will reach a low point and then start rising again This means that you have passed the optimum point for Channel 21 Extend the antenna a short distance and again follow the procedure above When the lowest point has been reached switch to Channel 1 on Band A and then to Channel 40 on Band F and compare SWR readings They should be almost equal B Antennas that must be cut to proper length 1 Follow the same procedure as above but adjust the length by cutting in 1 8 increments until a good match is obtained 2 Be very careful not to cut too much at one time as one it is cut it can no longer
14. tenna provides the most reliable operation and greatest range Shorter loaded type whip antennas are more attractive compact and adequate for applications where the maximum possible distance is not required Also the loaded whips do not present the problems of height imposed by a full quarter wavelength whip Mobile whip antennas utilize the metal body of the vehicle as a ground plane When mounted at a corner of the vehicle they are slightly directional in the direction of the body of the vehicle For all practical purpose however the radiation pattern is nondirectional The slight directional characteristic will be observed only at extreme distance A standard antenna connector type SO239 is provided on the transceiver for easy connection to a standard PL 259 cable termination If the transceiver is not mounted on a metal surface it is necessary to run a separate ground wire from the unit to a good metal electrical ground in the vehicle When installed in a boat the transceiver will not operate at maximum efficiency without a ground plate unless the vessel has a steel hull Before installing the transceiver in a boat consult your dealer for information regarding an adequate grounding system and prevention of electrolysis between fittings in the hull and water TUNNING THE ANTENNA FOR OPTIMUM SWR Since there is such a wide variety of base and mobile antennas this section will strictly concern itself to the various types of mobile adju
15. wise to apply power to the unit and to set the desired listening level During normal operation the VOLUME control is used to adjust the output level obtained either at the transceiver speaker or the external speaker if used SQUELCH outer dual concentric This control is used to cut off or eliminate receiver background noise in the absence of an incoming signal For maximum receiver sensitivity it is desired that the control be adjusted only to the point where the receiver background noise or ambient backgrounds noise is eliminated Turn fully counterclockwise then slowly clockwise until the receiver noise disappears Any signal to be received must now be slightly stronger than the average received noise Further clockwise rotation will increase the threshold level which a signal must overcome in order to be heard Only strong signals will be heard at a maximum clockwise setting MIC GAIN inner dual concentric Adjust the microphone gain in the transmit and PA modes This controls the gain to the extent that full talk power is available several inches away from the microphone RF GAIN CONTROL outer dual concentric Use to reduce the gain of the RF amplifier under strong signal conditions 8 10 11 12 13 14 DIMMER inner dual concentric Turns on off the frequency display channel number and the meter lamp Switch on at minimum brightness and rotate clockwise for brighter illumination RF POWER outer dual co
Download Pdf Manuals
Related Search