User`s Manual U User`s Manual
Contents
1. eko Dishwasher DIS15010 Users Manual Please read this user manual first Dear Customer We hope that you get the best results from your product which has been manufactured with high quality and state of the art technology Therefore please read this entire user manual and all other accompanying documents carefully before using the product and keep it as areference for future use If you handover the product to someone else give the user manual as well Follow all warnings and information in the user manual Remember that this user manual is also applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this User Manual the following symbols are used Warning for hazardous AN situations with regard to life and roperty Packaging materials of the product are manufactured C from recyclable materials in accordance with our National Environment Regulations Important information or useful hints about usage Warning for electric shock Do not dispose of the packaging materials together with the domestic or other wastes Take them to the packaging material collection points designated by the local authorities CONTENTS 1 INSTRUCTIONS FOR SAFETY 5 OPERATING THE PRODUCT22 AND ENVIRONMENT 4 Howto cancel the washing General safety eere2. gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine e Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing 30 35 EN Dishwasher User s Manual Troubleshooting the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme There is a different odour in the machine Anew machine has a peculiar odour It will fade out after a couple of washes i Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care e Dirty dishes are kept in dishwasher for 2 3 days gt gt gt If you are not going to start the machine right after you have put the dishes into it remove the remnants on the dishes and run the Prewash programme without detergent every 2 days In such cases do not close the door of the machine completely in order to avo
3. 4 PrOgTAMME serres peee 23 Ned E l USC a a LLN 4 How to change the washing Children s safety sse 5 programme Q a 23 Disposing of packaging material 5 Half Load Function Q 23 Transportation of the product 5 Tablet Detergent Function 23 Compliance with WEEE Directive and Time Delay asss 23 Disposing of the Waste Product 6 Warning Sound and Inner Illumination Compliance with RoHS Directive 6 Settings Depends on model 24 Package information 6 i 6 MAINTENANCE AND 2 DISHWASHER 7 CLEANING 26 OVEerVIeW miniainiinniiiioniinna 7 Cleaning the outer surface of the Condensing Drying System B PlOGUCl Asawa aaa au asa 26 Technical specifications 8 Cleaning the interior of the machine26 Cleaning the filters sssr 26 3 INSTALLATION 9 Cleaning the hose filter 27 Appropriate installation location 9 Cleaning the impellers wn 27 Connecting water supply Q Lowerimpeller 27 Connection to the drain 10 Upperimpeller 28 Adjusting the feet 10 Electrical connection 10 7TROUBLESHOOTING 29 This appliance must be earthed 11 Fitting a different plug 11 8 GUARANTEE 34 Initial USE u u inini 11 4 PREPARATION 12 Tips for energy saving 12 Water softening
4. amp Freezers 0845 6004903 or 0345 6004903 Electric Cookers 0845 6004902 or 0345 6004902 Gas amp Dual Fuel Cookers 0845 6004905 or 0345 6004905 Washing Machines 0845 6004906 or 0345 6004906 amp Dishwashers Republic of Ireland All Refrigeration All Cookers 01 862 3411 Washing Machines amp Dishwashers Before requesting service please check the trouble shooting guide in the Operating Instructions as a charge may be levied where no fault is found even though your product may still be under guarantee Service once the manufacturers guarantee has expired If you have purchased an extended guarantee please refer to the instructions contained within the extended guarantee agreement document Otherwise please call the appropriate number above where service can be obtained at a charge Should you experience any difficulty in obtaining service please contact the Beko Customer Help Line Tel 0845 6004911 e mail service beko co uk Beko pic Beko House 1 Greenhill Crescent Watford Hertfordshire WD18 8QU UK www beko co uk 15 0224 0100 REV AA 04 2015 Dishwasher User s Manual 35 35 EN
5. exceeds 10 bars a pressure relief valve should be installed in between Open the tap completely after making the connections to check for water leaks For your safety close the water inlet tap completely after the washing programme is over Dishwasher User s Manua 9 35 EN Installation Connection to the drain Water discharge hose can directly be connected to the drain hole or sink s drainage The length of this connection must be min 50 cm and max 100 cm from the floor A discharge hose longer than 4 meters will cause washing performance to be affected Attach the water discharge hose to the drainpipe without bending it Tightly fix the water discharge hose to the drainpipe in order to prevent any dislocation of the water discharge hose during operation of the product si max 100 cm ig z 2 min 50 cm min 4cm Drainpipe must be connected to the foul water system and it should not be connected to any surface water drain Adjusting the feet If the door of the product cannot be closed properly or if the product wobbles when you push it slightly then you need to adjust the feet of the product Adjust the feet of the product as illustrated in the relevant section Electrical connection Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating label corresponds to your electri
6. if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine Detergent dispenser lid is left open gt gt gt Make sure that the detergent dispenser lid is closed tightly after adding detergent Dishes are not dry at the end of cycle Dishes are not placed orderly in the machine gt gt gt Place your dishes in a way that no water will accumulate in them Dishwasher User s Manual 29 35 EN Troubleshooting e Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine e Machine is unloaded right after the programme is over gt gt gt Do not unload your machine right after washing process is completed Slightly open the door and wait for evacuation of the steam inside for a while Unload the dishes after the pieces cool down to a touchable level Start unloading process from the lower basket Thus dropping of water remained on a piece at upper basket onto the pieces at lower basket is prevented Selected programme is unsuitable gt gt gt Since rinsing temperature is low at programmes with short duration drying performance will also be low Select programmes with longer duration for a higher drying performance e Surface quality of the kitchen utensils is deteriorated gt gt gt Desired washing performance can not be obtained on kitchen u
7. in the user manual Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Impellers are stuck gt gt gt Prior to starting the programme turn the lower and upper impellers by hand to make sure that they rotate freely Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as illustrated in section Cleaning and Care Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Filters are installed incorrectly gt gt gt Check the filter system and make sure that it is installed correctly Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it in a closed container if possible For ease of storing we recommend you to use tablet detergents Detergent is not sufficient gt gt gt If you are using powder detergent adjust the amount of detergent according to the soiling degree of your dishes and or programme definitions We recommend you to use tablet detergents for optimum results Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid
8. in the User Instructions Booklet provided Professional installation by a qualified Electrical Domestic Appliance Installer is recommended for all Washing Machines Dishwashers and Electric Cookers Gas Cookers must only be installed by a Gas safe or BORD GAIS registered Gas Installer The guarantee is given only within the boundaries of the United Kingdom and the Republic of Ireland The guarantee is applicable only to new products and is not transferable if the product is resold Beko disclaims any liability for incidental or consequential damages The guarantee does not in anyway diminish your statutory or legal rights The product guarantee does not cover damages to plates glass ware cutlery crockery and also damage to the product itself as a result of using these Three in one Two in one detergents 34 35 EN Dishwasher User s Manual Guarantee Please keep your purchase receipt or other proof of purchase in a safe place you will need to have it should the product require attention under guarantee You should also complete the details below it will help us assist you when requesting service The model number is printed on the Instruction Booklet and the serial number is printed on the Rating Label affixed to the appliance Model No Serial No Retailer Date of purchase For service under quarantee simply telephone the appropriate number below UK Mainland amp Northern Ireland Fridges
9. items particularly such as knives are used for purposes other then their intended uses gt gt gt Protective cover on the edges of knives may get damaged when they are used for purposes such as opening cans Do not use metal kitchen utensils out of their intended uses Cutlery are made of low quality stainless steel gt gt gt Corrosion on such items is inevitable they should not be washed in dishwashers e Kitchen utensils that are already corroded are washed in dishwasher gt gt gt Rust ona corroded item can migrate to other stainless steel surfaces and cause corrosion on those surfaces as well Such items should not be washed in dishwashers Dishwasher User s Manual 31 35 EN Troubleshooting Detergent remains in detergent dispenser Detergent dispenser was damp when adding detergent gt gt gt Make sure that the detergent dispenser is dried well prior to filling it with detergent e Detergent is added long before the washing process gt gt gt Pay attention to add detergent shortly before start up of the washing e Opening of the detergent dispenser lid is prevented during washing gt gt gt Place the dishes in a way that will not prevent the detergent dispenser lid from opening and the water going into the machine from impellers e Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it ina closed co
10. start pause cancel button and close the door of your machine With the Half Load option you can use every part of your lower and upper baskets and you can Save by using less water and power Tablet Detergent Function Depending on the hardness level of the tap water the Tablet Detergent function allows obtaining a better drying performance from the multi purpose detergents such as 2in1 3in1 4in1 5in1 etc called all in one tablets The programmes in which the tablet detergent function can be enabled are indicated in the Programme Data and Table of Average Consumption Values Tablet Detergent Indicator lights when the Tablet Detergent function is selected Salt and Rinse Agent indicators turn off when this function is activated Time Delay Using the Delayed Start button you may delay the starting time of your programme up to 9 hours After delaying the start press Start Cancel button and close the door of your machine Once the delay time Dishwasher User s Manual 23 35 EN Operating the product is over the selected programme will start automatically Cancelling the delay function Keep the Start pause cancel button pressed for 3 seconds The selected delay period will be cancelled As soon as the cancelling starts the water remaining in your machine will be drained for 30 seconds due to safety reasons Warning Sound and Inner Illumination Settings Depends on model You can use the submenu set
11. afe detergents rinse aids and additives must be used The manufacturer waives any responsibility arisen from incorrect usage or transportation This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not pay with the appliance Cleaning and user maintenance shall not be made by children without Supervision Children s safety Electrical products are dangerous for the children Keep children away from the product when itis in use Do not let them to tamper with the product Donot forget to close the door of the product when leaving the room where it is Store all detergents and additives in a safe place away from the reach of the children Disposing of packaging material Packaging materials are dangerous to children seep packaging materials in a safe place away from reach of the children f Packaging materials of the product are manufactured from recyclable materials Dispose of them properly and sort in accordance with recycled waste instructions Do not dispose of them with normal domestic waste Transportation of the product If you need to move the product do it in upright position and hold from the rear side Tilting th
12. cape e Press and hold start pause cancel button for 3 seconds The start stop indicator light will start flashing Close the door The machine will drain the water inside the machine for 45 seconds e The programme is cancelled when start stop indicator light goes off Then you can choose and start anew programme programme you have cancelled there may be detergent residue or rinse aid inside the machine and on the load Make sure the items in the dishwasher are not used before washing properly i Depending on the stage of the How to change the washing programme To change the programme selection while the machine is operating e Open the door Care must be taken when opening the door as steam will escape e Press Start pause cancel button The indicator light will go off Select the new programme Press start pause cancel button The indicator light will be on and new programme will start It will start from the stage last carried out by the previous programme selection The new programme will NOT i Start right from the beginning Half Load Function If you want to run your machine without loading it completely place your dishes into the machine as you desire Press the On Off button to turn on your machine Press the Half Load Combi Tablet button after selecting the desired program until Half Load Indicator lights up then press
13. city supply We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position If the supply cord or the mains lead is damaged please do not replace it yourself The supply cord or the mains lead must be replaced by a Authorised Service Agent ora similarly qualified person 10 35 EN Dishwasher User s Manual Installation This appliance must be earthed If the fitted moulded plug is not suitable for your socket then the plug should be cut off and an appropriate plug fitted Destroy the old plug which is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house The moulded plug on this appliance incorporates a13A fuse Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used Do not forget to refit the fuse cover In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been fitted Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug Fuse covers are available from any good electrical store Fitting a different plug As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug proceed as follows 1 Connect the green yellow or green earth
14. desired programme by using the Programme Selection Button You may use Half Load Combi Tablet button Delayed Start Button features as necessary e Press start pause cancel button e Close the door then programme starts e Anaudio signal with an interval of 8 seconds warns you to switch your machine off when the selected washing programme ends This audible signal will warn you 10 times before it turns off 12345 P1P3P5 8 369 P2P4P6 2 1110 98 76 7 Time Delay Button 8 Rinse Aid Indicator Light 9 Half Load Indicator Light 10 Half Load Tablet Detergent Button 11 Programme Selection Button 12 On Off Button Do not open the dishwasher AN door whilst the appliance isin operation However in case the door is opened while the machine is working then a safety mechanism ensures the machine immediately stops Water may be very hot so be careful Care must be taken when opening the door as steam will escape VAN e Press the on off button after the programme is completed The indicator lights will go off e Unload the baskets we recommend to turn off the water tap when not in use 22 35 EN Dishwasher User s Manual Operating the product How to cancel the washing programme To cancel a programme while the machine is operating Open the door Care must be taken when opening the door as steam will es
15. duct are obtained in the laboratory on basis of the relevant standards Depending on operational and environmental conditions of the product these values may vary Condensing Drying System Condensing drying system ensures efficient drying of your dishes Note for test institutions Data required for performance tests shall be provided upon request Requests can be e mailed to the following address dishwasher standardloading com Do not forget to provide the code stock and serial numbers of the product to be tested in your request e mail along with your contact information Code stock and serial numbers of the product may be found on the type label attached to the side wall of the door 8 35 EN Dishwasher User s Manual E Installation To make the product ready for use make sure that the electricity tap water supply and water drainage systems are appropriate before calling the Authorised Service Agent If they are not call a qualified technician and plumber to have any necessary arrangements carried out Preparation of the location i and electrical tap water and waste water installations at the place of installation is under customer s responsibility Manufacturer shall not be held responsible for damages arising from processes carried out by unauthorised persons Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged p
16. e product onto its front Side may cause the electronic parts in it get wet and damaged 1 Unplug the product before transporting It 2 Remove water drainage and water supply connections 3 Drain the remaining water in the product completely Dishwasher User s Manual 5 35 EN Instructlons for safety and environment Compliance with WEEE collection points designated by Directive and Disposing the local authorities of the Waste Product This product complies with EU WEEE Directive 2012 19 EU This product Dears a Classification symbol for waste electrical and electronic equipment WEEE This product has been f manufactured with ng ay parts and materials which can be reused and are suitable for recycling Do not dispose of the waste product with normal domestic and other wastes at the end of its service life Take it to the collection center for the recycling of electrical and electronic equipment Please consult your local authorities to learn about these collection centers Compliance with RoHS Directive The product you have purchased complies with EU RoHS Directive 2011 65 EU It does not contain harmful and prohibited materials specified in the Directive Package information Packaging materials of the Poou are manufactured rom recyclable materials in accordance with our National Environment Regulations Do not dispose of the packaging materials together with the domestic or oth
17. ely and will also cause scratches on the glassware AA Tablet detergents Tablet detergents exhibit water softening and or rinse aid effect in addition to detergent effect Some types of these detergents also contain special purpose washing chemicals such as glass and stainless steel protectors Tablet detergents give Satisfying results only under certain usage conditions The best washing performance in dishwashers is obtained by using detergent rinse aid and water softening salt individually Information about suitable places detergent dispenser basket etc in the dishwasher to place the tablet can be found amongst the usage instructions on the packages of the tablet detergents i Tablet detergent types commonly found in the market 16 35 EN Dishwasher User s Manual Preparation 2in1 Contains detergent rinse aid or water softening salt 3in1 Contains detergent rinse aid and water softening salt 4in1 Contains glass protectors in addition to detergent rinse aid and water softening Salt 5in1 Contains glass and stainless steel protectors in addition to detergent rinse aid and water softening salt Observe the instructions of the i detergent manufacturer on the package when using tablet detergents When you switch to powder detergent from tablet detergent 1 Make sure that salt and rinse aid reservoirs are full 2 Setthe water hardness to the hig
18. er wastes Take them to the packaging material 6 35 EN Dishwasher User s Manual 2 Dishwasher Overview 12 11 10 ow oN 7 9 AN p Y gt A Upper impeller Lower basket Lower impeller Filters Rating Label Control panel Door Detergent dispenser Cutlery basket 10 Salt reservoir lid 11 Upper basket rail 12 Upper basket 13 Condensing Drying System om Nom pop Dishwasher User s Manual 7 35 EN Dishwasher Technical specifications Compliance to standards and test data EC declaration of conformity C This product complies with the following EU directives Development production and sales stages of this product comply with the safety rulesincluded in allpertaining European Community regulations 2006 95 EC 2004 108 EC 93 68 EC IEC 60436 DIN 44990 EN 50242 220 240 V 50 Hz see rating label Total power consumption 1800 2100 W see rating label Heater power consumption 1800 W see rating label Total current depends on the model 10 A see rating label Drain pump power consumption 30 W see rating label Mpa i i Values stated on the markings of the product or in the printed documents Technical specifications may be changed without prior notice to improve the quality of the product Figures in this manual are schematic and may not match the product exactly accompanying the pro
19. g 3 Select the water hardness level suitable to your machine from the Water Hardness Level Adjustment Table by pressing the Delayed Start Key 4 Press Start Pause Cancel key for once to store the level you have selected 5 Start Stop icon will light continuously when the new water hardness level is stored 6 Press the On Off button to turn off your machine Water Hardness Level Adjustment Table Hardness English Water German Water French Water Level Hardness dE Hardness dH Hardness dF Water Hardness Level Indicator 0 1 Level evel 5 Press the Programme Selection button to set the water hardness 3 Level If the hardness level of the water that you use is above 90 dF French standard for water hardness or if you are using well water than it is recommended to use filter and water purification devices If the hardness level of the water that you use is below 8 dF French standard for water hardness there is no need to use salt in your dishwasher If this is the case No Salt Ewe wes n level to P1 position 6 e e 14 35EN Dishwasher User s Manual Preparation Warning Indicator if any illuminates continuously on the panel of your machine If the water hardness adjustment is set to level 1 the No salt warning indicator will illuminate continuously although it is not necessary to use Salt If you use salt under this condition salt will not be consumed and the lamp wi
20. g to purchase is suitable for washing especially in the dishwasher Placing the dishes into the dishwasher You can use your dishwasher in the optimum way with respect to energy consumption and washing and drying performance only if you place the dishes in an orderly way e Wipe away any coarse food remnants bones seeds etc on the dishes before placing them in the dishwasher 18 35 EN Dishwasher User s Manual Preparation Suggestions for loading the dishwasher MS Z APD Upper basket Dishwasher User s Manual 19 35 EN Preparation Cutlery basket Push the latches back into the correct Cutlery basket is designed to wash your position dishes such as knife fork spoon etc in an efficient manner Since the cutlery basket can be moved A B you can create more space while placing your dishes in the lower basket and free up space for your dishes of different sizes RUS eu NESS Height setting with empty basket In this model the height setting of the upper basket may be changed using the wheels which are mounted at two different heights Release the latches on both the right and left tracks of the upper basket by pushing them outwards Pull out the basket out completely Place the basket back into the tracks at the desired hei
21. ght 20 35 EN Dishwasher User s Manual Preparation Collapsable lower basket wires Foldable wires A located at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc You can create larger spaces by folding each wire individually or all of them at once To bring the collapsible wires into horizontal position grab the wire from mid position and push them in the directions of arrows B To bring the wires back to vertical position just lift them up Collapsible wires will click into the latch again C Bringing the wires to the horizontal position by holding them from the tips may cause them to bend Therefore it will be appropriate to bring the wires in the middle to horizontal or vertical position by holding them from their stems and pushing in the direction of arrow Dishwasher User s Manual 21 35 EN 5 Operating the product 1 Programme Indicator Light 2 Tablet Detergent Indicator 3 Salt Level Indicator Light 4 Time Delay Indicator 5 Start Stop Indicator Light 6 Start Stop Button e Pushin the on off button and check that the programme indicator lights come on e Check the salt and rinse aid level indicator lights before you start the machine If necessary add salt and rinse aid e Select the required programme by referring to the programme chart e Select the
22. hest level and perform an empty run 3 After the empty washing cycle review the user manual and readjust the water hardness level so as to suit the water supply 4 Make the appropriate rinse aid settings i Rinse aid i Depending on the model salt indicator and or rinse aid indicator must be enabled again if they were disabled before The rinse aid used in dishwashers is a special combination used to increase drying efficiency and prevent water or limescale stains on the washed items For this reason care must be paid to have rinse aid in the rinse aid reservoir and to use rinse aids produced specially for dishwashers only 1 Open the lid of the rinse aid reservoir by pressing its latch B 2 Fillthe reservoir until MAX level 3 Close the lid of the reservoir by pressing on it lightly Wipe clean any spilled rinse aid outside the reservoir Rinse aid that spilled accidentally will cause foaming and it will eventually decrease washing performance 4 Turn the rinse aid amount adjuster manually to a position between 1 and 6 4 If there are stains on tableware items after washing level must be Dishwasher User s Manual 17 35 EN Preparation increased and if there is a blue trace e Place thin narrow pieces in the middle after wiping them by hand it must be sections of baskets if possible decreased This is set to po
23. id odour build up in machine You can also use commercially available odour removers or machine cleaners Rust discoloration or surface deterioration occurs on dishes Salt leakage exists gt gt gt Salt may cause deterioration and oxidation on metal surfaces Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the Salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme Salty food remnants have remained on dishes for along time gt gt gt If silverware soiled with such foods will be kept waiting in machine dirt must be removed by prewash or dishes must be washed without being kept waiting Electric installation is not grounded gt gt gt Check if your machine is connected to the actual grounding line Otherwise the static electric created in the product causes arcs on the surfaces of metal items creating pores removing the protective cover on the surface and causing discoloration e Intensive cleansers such as bleaches are used gt gt gt Protective cover on metal surfaces gets damaged and looses its efficiency in time when it gets in contact with cleansers such as bleach Do not wash your dishes with bleach e Metal
24. inS jqe uuu te1Boid eld S 8 W9 SL U19 SZ V sjuab19 0q Buljlos jo aa160q BunieA 1d y ue yey s usip l ep palos uunip ui y 10 uuuue1Boid Bulysem IeS9 tuouo25 8 1SOW aunyesadwia Bulue 5S aweu uuuue1Boid saquinu uuuue1Boid 25 35 EN Dishwasher User s Manual 6 Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if it is cleaned at regular intervals Unplug the product and turn off Do not use abrasive substances for cleaning the tap before attempting any Cleaning the filters Clean the filters at least once a week in order for the machine operates efficiently Check if food residues are left on the filters If there are food residues on filters take them out and clean well under running water 1 Turn the micro filter 1 and coarse filter 2 assembly counterclockwise and pull Clean the filter and impellers at least once a week to ensure the machine operates efficiently cleaning procedures Cleaning the outer surface of the product Clean the outer surface and door gaskets of the product gently with a mild cleaning material and damp cloth Wipe the control panel only with a damp cloth Cleaning the interior of the machine e Clean the interior of the machine and the tank by running a prewash programme without detergent or a long washing programme with detergent based on
25. its seat in the hose 4 Install the hose to tap depends on model Cleaning the impellers Clean the impellers at least once a week in order for the machine operates efficiently Lower impeller Check if the holes on the lower impeller 1 are clogged If they are clogged remove and clean the impeller Pull the lower impeller up to remove it A B w Z A N Dishwasher User s Manual 27 35 EN Maintenance and cleaning Upper impeller Check if the holes on the upper impeller 1 are clogged If they are clogged remove and clean the impeller Turn its nut to left to remove the upper impeller A B Make sure that the nut is tightened well when installing the upper impeller Wy wx 7 28 35 EN Dishwasher User s Manual 7 Troubleshooting Machine does not start Power cable is unplugged gt gt gt Check if the power cable is plugged in Fuse is blown gt gt gt Check the fuses in your house Water is cut gt gt gt Make sure that the water inlet tap is open Door of the machine is open gt gt gt Make sure that you have closed the door of the machine On Off button is not pressed gt gt gt Make sure that you have turned on the machine by pressing the On Off button Dishes are not washed clean Dishes are not placed orderly in the machine gt gt gt Load the dishes as described
26. ll not illuminate i If you move your house it is very important to make the water hardness level adjustment of your machine according to the new location you move in order to preserve the washing efficiency If the water hardness level of your machine is adjusted previously your machine will display the last water hardness level adjustment Adjust the new water hardness level of your machine on basis of the water hardness level of your tap water Since different salt brands in the market have different particle sizes and since the water hardness may vary dissolution of the salt in water may take a couple of hours Therefore Salt Indicator remains on for a while after adding salt into the machine Loose salt grains can cause rust marks in your machine if not rinsed away Only fill salt just before a programme is run Detergent You can use powder or tablet detergent in the machine i Only use in the machine the detergents produced particularly for use with dishwashers We recommend you not to use detergents that contain chlorine and phosphate as they are harmful for the environment i Contact the detergent producer if the dishes are wet and or if you notice limescale spots particularly on glasses after the washing programme is over Adding detergent i Refer to the Programme Table to determine the correct amount of detergent for the selec
27. mme data and average consumption values Do not put more detergent than suggested on the detergent package Water softening system G Your dishwasher requires soft water If the hardness of the water is above 6 dH the water must be softened and descaled Otherwise ions that create the hardness will accumulate on the surfaces of the dishes and may adversely affect the washing shining and drying performances of the product The product is equipped with a water softening system which reduces the hardness of incoming water This system softens the supply water that enters into the product to a level that will allow washing the dishes with the required quality Adjusting the water softening system Washing performance will increase when water softening system is adjusted properly Adjust the new water hardness level according to the Water hardness level instruction in this booklet Adding salt Water softening system needs to be regenerated in order that the product operates with the same performance continuously Dishwasher salt is used for this purpose Use only special softening salts produced particularly for the dishwashers in your machine We recommend using granular or powder softening salts Do not use Salts that are insoluble in water such as table salt or common salt Performance of water softening system may get worse in time E E Salt reservoir will fill with wa
28. n Ou z Unplug the product when not in use Never wash the product by sles pouring water onto it There is the risk of electric shock l Never touch the plug with wet hands Never unplug by pulling on the cable always pul out by grabbing the plug he product must be unplugged during installation maintenance cleaning and repairing procedures f Always have the repair procedures carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised ersons Never use chemical solvents in the product They bring forth the risk of explosion When you pull the upper and lower baskets out completely the door of the product will bear all the weight of the baskets Do not put other loads on the door ass the product may tiit Never leave the door of the product open apart from loading and unloading rocedures o not to open the door of the product when it is running unless necessary Be careful for the rush o hot steam when you need to open the door Intended use This product has been designed for domestic use 4 35 EN Dishwasher User s Manual Instructlons for safety and environment It must be used to do the domestic type dishes only This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops offices and other working environments Only dishwasher s
29. ntainer if possible For ease of storing we recommend you to use tablet detergents Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as illustrated in section Cleaning and Care Decorations and ornaments on kitchen utensils are being erased i Decorated glasses and decorated lustre porcelains are not suitable for washing in the dishwasher Manufacturers of some glassware and porcelain tableware items do not recommend washing such kitchen utensils in the dishwashers either Dishes are scratched Kitchen utensils that contains or are made of aluminum should not be washed in dishwasher Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Spilled salt can cause scratches Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme e Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting e Dishes are not placed orderly in the machine gt gt gt When placing the glasses and o
30. nteed against the cost of breakdown repairs for two years from the date of the original purchase What is covered e Repairs necessary as a result of faulty materials defective components or manufacturing defect The cost of functional replacement parts but excluding consumable items e The labour costs of a Beko approved repairer to carry out the repair What is not covered e Transit delivery or accidental damage or misuse and abuse e Cabinet or appearance parts including knobs flaps handles or container lids e Accessories or consumable items including but not limited to ice trays scrapers cutlery baskets filters and light bulbs e Repairs required as a result of unauthorised repair or inexpert installation that fails to meet the requirements contained in the user instruction book Repairs to products used on commercial or non residential household premises Loss of frozen food in freezers or fridge freezers Food loss insurance is often included within your household contents insurance policy or may be available separately from your retailer Important notes Your Beko product is designed and built for domestic household use only The guarantee will be void if the product is installed or used in commercial or non residential domestic household premises The product must be correctly installed located and operated in accordance with the instructions contained
31. p provided If you move to a different location the level of water hardness will possibly be different It is essential to reset the water hardness in order to obtain optimum washing efficiency Dishwasher User s Manual 13 35 EN Preparation Test Strip f Level 1 No Lime Level 2 II Very low lime content Level 3 BN H ow lime content Level 4 NN EN E Medium lime content Level 5 NN E HN H High lime content Level6 BN BH W W MM Very High lime conten Remove the Letthe water Filla glass with Take the test strip Hold for Set the water hardness level of your dishwasher test strip from flow from your tap water and out of the water and 1 minute according to the result shown by the test strip its packing tap for 1 minute dip the test strip shake it into water for 1 second To Adjust the Water Hardness 1 Turn onthe machine by pressing On Off key while pressing and holding the Programme Selection key when the machine is in off position Press and hold the programme key until the water hardness level stored on your machine is displayed in the program indicator Start Pause indicator will start flashing once the stored water hardness setting is displayed 2 Byusing Programme Selection key adjust water hardness level according to the hardness of the supply water See Water hardness level adjustment table for correct settin
32. roducts cause risks for your safety i Make sure that the water inlet and discharge hoses are not folded pinched or crushed while pushing the product into its place after installation or cleaning procedures When placing the product pay attention not to damage the floor walls piping etc Do not hold the product from its door or panel to move it Appropriate installation location Place the product on a solid and flat floor that has sufficient load carrying capacity The product must be installed on a flat surface in order for the door to be closed comfortably and securely Do not install the product at places where temperature may fall below orc Place the product on a rigid floor Do not place it on a long pile rug or similar surfaces Ensure the power cable does not get trapped under the product Make sure that you select a location that will allow you to load and unload the dishes in a fast and comfortable manner Install the product in a place close to the tap and the drain Select the installation location by considering that it will not be changed after the connections are made Connecting water supply Do not use old or used water inlet hose on the new product Use the new water inlet hose supplied with the product Connect the water inlet hose directly to the water tap Pressure coming from the tap should be minimum 0 3 and maximum 10 bars If the water pressure
33. sition 4 as e There are two separate baskets in factory default which you can place your dishes in the Items not suitable for washing in the dishwasher Place the heavily soiled dishwasher and bigger items in the lower basket e Never wash dishes soiled by cigarette and smaller delicate and light items in ash candle remnants polish dyestuff the upper basket chemicals etc in your dishwasher e Place the hollowed dishes such as e Donotwash iron alloy items in the bowls glasses and pans upside down dishwasher It can get corroded or in the dishwasher Thus accumulation leave stains on other items of water in deep hollows is prevented Do not wash silverware and cutlery To prevent possible injuries with wooden or bone stems glued AN always place the sharp and pieces or pieces that are not resistant pointed dishes such as service to heat as well as copper and tin fork bread knife etc upside plated containers in the dishwasher down so as their pointed ends Decorative prints of chinaware will face down or they will lie i as well as aluminum and silver horizontally in the dish basket items may get discoloured Unload dishes in the lower basket first and or tarnished after washing then the dishes in the upper basket in the dishwasher just as it happens in handwashing as well Some delicate glasstypes Upper basket rack and crystals may become dull in time We strongly recommend you to check if the tableware you are goin
34. system 12 Adjusting the water softening SyS CEM ia u anna ata uakis aaa 12 Adding Salt aaa aina 12 Water hardness amp regeneration SETT NGS asirans einiino uenir 13 Detergent sts 15 Adding detergent 0 15 Tablet detergents 16 RINSE OIG Grsrewatiennvisvtnnvindie 17 Upper basketrack 18 Cutlery DASKE Erisan 20 Height setting with empty basket 20 Collapsable lower basket wires 21 EBinstructions for safety and environment This section contains safety instructions that will help to give protection from risk of personal injury or property damage Failure to follow these Instructions shall void all warranties General safety Never place the product on a carpet covered floor otherwise lack of airflow beneath the product will cause electrical parts to overheat This will cause proar m with your product Do not operate the product if the power cable plug is damaged Call the Authorised Service Agent Connect the product to a arenan outlet protected y a fuse complying with the values in the Technical specifications table Do not neglect to have the en ing installation made y a qualified electrician Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations The water supply and draining hoses mustbe securely fastened and remai
35. t gt Take care that rinse aid is not spilled in the machine when you are filling it Clean any spilled rinse ait with the help of a tissue paper towel e Lid of the rinse aid reservoir is left open gt gt gt Make sure that the lid of the rinse aid reservoir is closed after adding rinse aid Kitchen utensils are broken e Dishes are not placed orderly in the machine gt gt gt Load the dishes as described in the user manual Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Water remains in the dishwasher at the end of the programme e Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care e Discharge hose is clogged blocked gt gt gt Check the discharge hose If necessary remove the discharge hose clear the blockage and insert is as illustrated in the user manual i If you cannot eliminate the problem although you follow the instructions in this section consult your dealer or the Authorised Service Agent Never try to repair a nonfunctional product yourself Dishwasher User s Manual 33 35 EN EI Guarantee Guarantee for Refrigeration Cooking Appliances Washing Machines amp Dishwashers Please visit the Support section on the Beko website at www beko co uk to register your two years warranty Your new Beko product is guara
36. ted programme A Do not put solvents into the detergent dispenser There is the risk of explosion Put the detergent into the detergent dispenser just before operating the machine as illustrated below 1 Push the latch to right to open the detergent dispenser lid A 2 Putsuggested amount of powder or tablet detergent in the dispenser Dishwasher User s Manual 15 35 EN Preparation G Inside the detergent dispenser there are level markings that help you use appropriate amount of detergent When brimful detergent dispenser will contain 40 cm of detergent Fill detergent up to 15 cm or 25 cm level marks in the detergent dispenser according to fullness of the machine and or soiling degree of the dishes 1 If dishes have been waiting for along time and have dried residues fill the 5 cm compartment too 5 i 3 Close the detergent dispenser lid by pressing on it lightly A click will be heard when the lid is closed In programmes with prewash and at high temperature in which you use tablet detergents make sure that the detergent dispenser lid is closed firmly i Use powder detergent in short programmes without prewash since the solubility of the tablet detergent changes depending on the temperature and time G Excessive usaqe of powder detergents will cause the detergent not dissolve complet
37. tensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well Also water can not flow easily on deteriorated surfaces It is not recommended to wash such kitchen utensils in dishwasher i Itis normal that drying complaints can be experienced with Teflon kitchen utensils It is associated with the structure of Teflon Since the surface tensions of Teflon and water are different water droplets will remain as beads on the Teflon surface Tea cafe or lipstick stains remain on dishes Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Surface quality of the kitchen utensils is deteriorated gt gt gt Tea and cafe stains or other dye spots may not be cleaned in dishwasher when they have penetrated in deteriorated surfaces Desired washing performance can not be obtained on kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well It is not recommended to wash such kitchen utensils in dishwasher e Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it ina closed container if possible For ease of storing we recommend you to use tablet detergents Lime traces remain on dishes and glassware gains a misty appearance Rinse aid is not sufficient gt gt
38. ter when you start the product Therefore add the softening salt before starting the machine e 1 First take the lower basket out to add softening salt 12 35 EN Preparation 2 Turn the salt reservoir lid counter clockwise to open it A B Salt reservoir will fill with water when you Start the product Therefore add the softening salt before starting the machine Before initial use fill the water softening system with 1 litre of water C 3 Fill the salt reservoir with salt by using salt funnel D To speed up dissolution rate of salt in water stir it with a spoon You can put about 2 kg of Dishwasher salt into the salt reservoir G 4 Replace the lid and tighten it securely when the reservoir is full 5 If you will not start a washing programme immediately after adding the salt run the machine empty in the shortest programme to dissolve and wash away the scattered Salt in the machine Water hardness amp regeneration settings The dishwasher requires lime free water Hard water leaves watermarks on your dishes Your dishwasher has a special water softening system to remove the hardness of the tap water Setting this system correctly will increase the washing effectiveness To find out the hardness level of water in your area contact your local Water Board or Determine water hardness level by the help of test stri
39. the degree of dirtiness e If water has remained in the machine drain the water by performing the procedures under the topic Canceling a programme If the water cannot be discharged clean any leftover deposits that have piled up in the bottom of the machine blocking the water path 2 Press the two pawls on the coarse filter inwards and separate the coarse filter from the assembly B 3 Pull out the metal plastic filter 3 from the seating C 26 35 EN Dishwasher User s Manual Maintenance and cleaning 4 Cleanall three filters under tap water by means of a brush 5 Replace the metal plastic filter 6 Place the coarse filter into the microfilter Make sure that it is properly seated Turn the coarse filter clockwise until a click sound is heard Do not use the dishwasher without filter i Incorrect placement of the filters will reduce washing efficiency i Cleaning the hose filter Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation such as sand dirt rust etc can be prevented by means of the filter attached to the water inlet hose Check the filter and the hose regularly and clean them if necessary 1 Turn off the tap and remove the hose 2 After taking out the filter clean it under running tap water 3 Place the cleaned filter back to
40. ther glassware into the basket lean them not against other dishes but the edges or racks of the basket or the glass support tines Striking of the glasses to each other or to other dishes due to the impact of water during washing can cause breaks or scratches on their surfaces 32 35 EN Dishwasher User s Manual Troubleshooting A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand A bluish rainbow appearance occurs the glass is pointed to light Excessive rinse aid is used gt gt gt Lower rinse aid setting Clean the spilled rinse aid when adding rinse aid Corrosion has occurred on glass due to soft water gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting If your supply water is soft lt 5 dH do not use salt Choose programmes that wash in higher temperatures e g 60 65 C You can also use glass protective detergents that are commercially available Foam forms in the machine Dishes are washed with hand wash detergent by hand but not rinsed before placing them into the machine gt gt gt Hand wash detergents do not contain antifoam There is no need to hand wash the dishes before placing them into the machine Removing the coarse soil on the dishes under tap water with a tissue paper or fork will be sufficient Rinse aid has spilled into the machine when adding rinse aid gt g
41. tings to change the Warning Sound and Inner IIlumination settings you will use in your machine To change the submenu settings Turn on your machine by pressing the On Off button while pressing and holding Programme Selection and Start Pause Cancel keys Firstly P1 indicator will light up on the display Select the desired setting P1 P2 P3 P4 by pressing the Programme Selection key P1 Warning Sound ON Inner illumination ON P2 Warning Sound OFF Inner illumination ON P3 Warning Sound OFF Inner illumination OFF P4 Warning Sound ON Inner illumination OFF Save the selected setting by pressing Start Pause Cancel key again 24 35 EN Dishwasher User s Manual p ue 5o 1d Jo padesos ase Jey S YSIP Aep pajos Anys 104 qe1ins Operating the product KEM S9 SEj BU u p ue o sse Bunrem 1d y ave yey seysip pallos winipaw y U9 IUA ye wei6oid Bulysem Ajreq asn juablejep Japmod I uO SUONIPUOD jeo Oe d JapUN INDDO Joj 1 u Aew s ou 1u Jjiq SUONIPUOD PJepUe s sapun p uluu181 p 21M 9 qQe y u UMOYS s njea uonduinsuo2o y uuuueJBoid 1s 94 Buisn pue omasa ple suu IIn e pue Jasuadsip yes J u ljos 1972M N e YM JNO paleo q 1snu ZPZOG N3 YPM soUepsJOIe UI s s BY s m sui Bus 104 uutuue15oid 5u 1 J u s usip p lios Ajjewsou sued pue sjod s usip Joy uuuue1Boid Hurysem Aeq payios lIAB u 104 qe
42. wire to the terminal in the plug marked E or with the symbol or coloured green and yellow or green 2 Connect the blue neutral wire to the terminal in the plug marked N or coloured black 3 Connect the brown live wire to the terminal in the plug marked L or coloured red Green and yellow or green Blue or black Brown or red With the alternative plugs a 13A fuse must be fitted either in the plug or adaptor or in the main fuse box If in doubt contact a qualified electrician Initial use Before starting to use the product make sure that all preparations are made in accordance with the instructions in sections Important safety instructions and Installation Before using the product fill the salt reservoir with 1 litre of water add salt see next page and stir to dissolve Run the Dishwasher without dishes ona short programme with a small amount of detergent There might be a small amount of water left in the product after factory quality control tests This causes no harm to the product Dishwasher User s Manual 11 35 EN 4 Preparation Tips for energy saving Following information will help you use the product in an ecological and energy efficient manner Wipe away any coarse food remnants on the dishes before putting them in the product Operate the product after filling it completely When selecting a programme consider the table of Progra
Download Pdf Manuals
Related Search