Home

ACTi E33/E34 Hardware Manual

image

Contents

1. eeseeeseeeene 23 Connecting Multiple Cameras ccccceccseeceeeeeeseeeeeeeeeeeeeeenees 24 Accessing the Camera 25 Configure the IP Addresses scere 25 Using DHCP Server to Assign IP Addresses 25 Using the Default Camera IP Address 27 Access the Camera 1 ecce eiie Leee riesen seen n enn anam a annuas 29 2 www acti com VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 na ACT Hardware Manual Other Adjustments and Accessories 32 Adjust the Viewing Angle sce eee ce recs eve eeu sg ever cecs cece seu ence este secesveren 32 Attach the Sunshield vsccsciscssesctesaisectsersessteessnntsnarwentanmeansteesenectonanecs 33 Appendix 34 How to Make an Ethernet Cable 34 3 www acti com VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision vA Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product Heed all warnings You must adhere to all the warnings on the product and in the instruction manual Failure to follow the safety instruction given may directly endanger people cause damage to the system or to other
2. Bullet Camera Series Hardware Manual E31 E32 E33 E34 Ver 2013 12 04 ACTI Connecting Vision RS VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision vA Hardware Manual Table of Contents Precautions 4 Salelv Inst UIC TIONS dorrera EEEE EE 6 Introduction 7 List of OGG Me denne 7 Package COMENS ERR 8 Physical DESCIIDUOM sosisini aa a 9 Installation Procedures 10 IVIQUIPIT TING CISL d sern E 10 Using the Bundled Bracket ccccccccecceecseeceeeeeeeeeeeeeseeseeeaeees 10 OTIC Mounting E DDIODS wsscaeccatsaeccatscceatecucasataauemeusumentataquemeutnen 13 Waterproof Cable Installation 14 Step 1 Remove the Pre installed Network Cable Pigtail 15 Step 2 Prepare the Conduit Gland and Flex Conduit 16 Step 3 Install the Ethernet Cable 17 Step 4 Connect the Ethernet Cable 18 Replace the Pre Installed Network Cable 19 Step 1 Remove the Pre installed Network Cable Pigtail 20 Step 2 Install the New Ethernet Cable 21 Basic Connections cccceeeeeeneeeeneeeenseeensesenseeensesensesensesensesenees 23 Connecting a Single Camera
3. 44 0 1245 808299 ACTI Connecting Vision bis Hardware Manual 3 Secure the clamping nut to the body NOTE Make sure the clamping nut is tight to avoid possible water leak Step 4 Connect the Ethernet Cable 1 Connect the Ethernet cable to the Ethernet port inside the camera 2 When done close the back cover by tightening the three 3 screws NOTE Make sure the rubber ring on the cover is secured and the screws are completely tightened to avoid possible water leak a VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 WA lt gt ACTI Connecting Vision Hardware Manual Replace the Pre Installed Network Cable The pre installed network cable comes with an Ethernet port female connector or known as a pigtail The length of the cable is around 14 35 cm varies by model The network cable and gland are resistant to salt water weak acid alcohol oil grease and common solvents In case the installation environment requires a change of this network cable follow the step by step procedures in this section to do so To replace the pre installed network cable prepare the following e Screwdriver e Ethernet cable without connectors e RJ 45 Connector x2 e RJ45 Crimping Tool NOTE The above materials tools are not included in the package 9 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax
4. A1D 500 V6 05 xx AC or newer QuickTime http www apple com quicktime download The camera firmware version can be found on the FW Version column of the IP utility or access the Setup page of the Web Configurator see page 31 Disclaimer Notice The camera manufacturer does not guarantee the compatibility of its cameras with VLC player or QuickTime since these are third party softwares The third parties have the right to modify their utility any time which might affect the compatibility In such cases please use Internet Explorer browser instead When using Internet Explorer browser the ActiveX control for video stream management will be downloaded from the camera directly the user just has to accept the use of such control when prompted so No other third party utilities are required to be installed in such case 2 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 V Hardware Manual The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera Assuming that the camera s IP address is 192 168 0 100 you can access it by opening the Web browser and typing the following address into Web browser s address bar http 192 168 0 100 Upon successful connection to the camera the user interface called Web Configurator would appear together with the login page The HTTP port number was not added behind
5. cameras with their new IP addresses Please note that it is also possible to change the IP addresses manually by using the Web browser In such case please plug in only one camera at a time and change its IP address by using the Web browser before plugging in the next one This way the Web browser will not be confused about two devices having the same IP address at the same time VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision vA Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment it is possible to use the Web browser of the PC to access the camera You can use any of the browsers to access the camera however the full functionality is provided only for Microsoft Internet Explorer The browser functionality comparison Functionality Internet Explorer Other browsers PTZ Contro Capture the snapshot Video overlay based configuration Motion Yes No Detection regions Privacy Mask regions When using non Internet Explorer browsers free third party software plug ins must be installed to the PC first to be able to get the live video feed from the camera Check the firmware version of the camera to determine which plug in is necessary Required Plug in A1D 500 V6 04 xx AC or older Basic VLC Media Player hitp www videolan org
6. 16 26 203 00 0F 7C 09 25 F6 A1D 500 V6 03 09 AC Megapixel IP Camera E31 A XX 121 00026 172 16 26 35 00 0F7C 09 8820 A1D 500 V6 03 17 AC Megapixel IP Camera E41 A XX 12L 00112 172 16 26 36 00 0F7C 09 8D 8F A1D 500 V6 03 17 AC MegapixelIP Camera E42 A XX 12K 00027 172 16 26 243 00 0F7C 09 8976 A1D 500 V6 03 17 AC Megapixel IP Camera E42 A XX 12L 00286 192 168 0156 00 0F7C 09 95 6C A10 500 V6 0203 AC Megapixel IP Dome ES3 A XX 12K 00147 17216286180 000F7C 09 05 8D A1D 500 V603 17 AC Megapixel IP Dome ES3 A 30 13A 00089 17216263 00 0F 7C 09 F8 F3 A1D 500 V6 03 10 AC Megapixel IP Dome E73 A XX 13A 00028 172 16 26 4 00 0F 7C 09 F9 57 A1D 500 V6 03 15 AC Megapixel IP Dome E83 A XX 13A 00018 172 16 26 186 00 0F 7C 0A C5 A3 ENR 010 V3 99 11 AC 16 CH Embedded NVR ENR2000 ENR2000 A 13D 00002 17216266 000F7C07DE66 A1D 311 V5 10 02 AC Hemispheric Camera KCM3911 124 X 00312 172 16 26 200 00 0F 7C 06 13 7B A1D 311 V5 08 06 AC Megapixel IP Camera KCMS111 11A X 00008 S STR J J NIN h h3 a i Pw a o e eo I o o eo o o N ho h h3 N ho C 9 oo gt J 4721626210 00 0F 7 11 05 07 A1D 311 V5 0507 AC Mega IP Camera KCM5311 11B X 00010 172 16 26 62 00 0F 7C 07 BB B7 A1D 311 V5 10 02 AC Megapixel IP Camera KCM5311 11L E 00010 Add Remove Device i x Http Port Remove amp n cn
7. 44 0 1245 808299 WA lt gt ACTI Connecting Vision Hardware Manual Step 1 Remove the Pre installed Network Cable Pigtail 1 Loosen the three 3 screws to detach the back cover NOTE A cable is connected inside the camera do not abruptly pull the back Cover 2 Disconnect the network connector A and remove the sealing nut B 3 Pull out the network cable from the back cover and disassemble the parts as marked below 4 Squeeze the seal to pull out the connector and then completely remove the seal claw and sealing nut from the network cable VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 V lt gt ACTI Connecting Vision Hardware Manual Step 2 Install the New Ethernet Cable 1 Insert the new Ethernet cable through the sealing nut claw seal and cable gland of the back cover 2 Attach the RJ 45 connector to the Ethernet cable See How to Make an Ethernet Cable on page 34 for more information 3 Assemble the seal and claw and then connect the RJ 45 connector to the Ethernet port inside the camera 4 Attach the back cover by tightening the three 3 screws NOTE Make sure the rubber ring on the cover is secured and the screws are completely tightened to avoid possible water leak VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 12
8. Reboot con HESSEN oc EE oos SNR f IP Address MAC Address FW Version Model Serial No Multicast IP Status Total 56 172 16 26 2 00 0F 7C 07 DE 65 A1D 311 V5 07 05 AC Hemispheric Camera KCM3911 228 5 6 1 172 16 26 4 00 0F 7C 08 17 C2 A1D 310 V4 12 02 AC Mega IP Camera TCM1111 228 5 6 1 172 16 26 6 00 0 KCM7311 228 5 6 1 Q Change Network Address 93 i 172 16 26 7 00 4 TCM6630 228 5 6 1 172 16 26 10 00 Dynamic IP Address TCM4201 228 5 6 1 172 16 26 11 00 0 KCM3911 228 5 6 1 172 16 26 13 go S Static IP Address KCM5111 228 5 6 1 p 172 16 26 40 00 4 KCM5211 228 5 6 1 Starting IP Address 172 16 26 41 00 0 KCM5311 228 5 6 1 172 16 26 50 00 4 Netmask KCM5111 228 5 6 1 172 16 26 52 00 4 KCM5311 228 5 6 1 Gateway E 172 16 26 53 00 4 TCM5311 228 5 6 1 172 16 26 54 00 4 TCM5611 228 5 6 1 172 16 26 55 00 1 TCM5111 228 5 6 1 172 16 26 57 00 0F 7C 04 87 A 41D 310 V4 12 09 A Video Server TCD2100 228 5 6 1 172 16 26 61 00 0F 7C 04 32 E3 A1D 310 V4 12 09 AC Megapixel IP Camera TCM1231 228 5 6 1 With the procedure shown above all the cameras will have unique IP addresses starting from 192 168 0 101 In case there are 20 cameras selected the last one of the cameras would have the IP 192 168 0 120 Later by pressing the Refresh button of the IP Utility you will be able to see the list of
9. aun un H oH N a 4 You can quickly see the camera model in the list Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 WA lt gt ACTI Connecting Vision Hardware Manual Using the Default Camera IP Address If there is no DHCP server in the given network the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment When the camera is plugged into network and it does not detect any DHCP services it will automatically assign itself a default IP 192 168 0 100 Whereas the default port number would be 80 In order to access that camera the IP address of the PC has to be configured to match the network segment of the camera Manually adjust the IP address of the PC In the following example based on Windows 7 we will configure the IP address to 192 168 0 99 and set Subnet Mask to 255 255 255 0 by using the steps below ME All Control Panel Items Network and Sharing Center RE Network and Internet Network Connt B Control Panel Home i i o fa View your basic network information and set up connections Organize v Disable this network device Diagnos Ch dapter setti
10. go through any opening VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision gt s Hardware Manual Attach the Sunshield The use of sunshield is optional if the camera will be installed indoors However if the camera will be installed outdoors attach the sunshield to protect the lens from all types of weather and lighting conditions 1 Loosely secure the supplied screws and washers to attach the sunshield 2 Slide to adjust the sunshield to cover the lens as far as possible but out of the camera s live view 3 Tighten the screws to fix the position of the sunshield VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 na ACT Hardware Manual Appendix How to Make an Ethernet Cable 1 Prepare the following tools e Ethernet cable without connectors e RJ 45 Connector x2 e RJ45 Crimping Tool e Scissors 2 Cut about 1 inch into the plastic sheath from the end of the cable 1 Stripe Orange 12345678 12345678 2 Orange S 3 Stripe Green 4 Blue 5 Stripe Blue 6 Green 7T Stripe Brown 8 Brown 4 Pinch the wires between your fingers and straighten them out 5 Use the scissors to make a straight cut across the wires 72 inch from the cut end 6 With the RJ 45 connector tab facing down push the wires into the connector all the
11. uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision vA Hardware Manual Introduction List of Models This hardware manual contains the following models 1MP Bullet with D N IR Basic WDR Fixed lens 3MP Bullet with D N IR Basic WDR Fixed lens 5MP Bullet with D N IR Basic WDR Fixed lens 3MP Bullet with D N IR Superior WDR Fixed lens 1 www acti com VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 V lt gt ACTI Connecting Vision Hardware Manual Package Contents Bullet Camera Sunshield Conduit Gland Mounting Screw Kit Sunshield Screw Kit Quick Installation Guide H Quick Installation Guide pi acti Padkaps cosent Gene oF emo femen Pae lex ur jenny tor Vm oon anc Tp Dec Pooc OD wea VA CO tan Vere Safe mi Wa met Gre Aequeet equigesenti betore eytellenion C se MA tent sunto manh roa si tee PC sa bare fase no lom baa 1 But retina Pat ve AIIN ue ao Q poe MEN SRT test maar ascen Bl cmt peee t Pm itm n bene mes Who pno Paddrew 6182100 Uaermame Aimo Pamwced 125436 Accwising Your Camera Astomatic P Setup wir Router DICP server E r Bracket Plate Bracket jactannty Priod 1 pres rem rd Bure EE eee Joie 1 i peren x matre m rp por tow pes Mal ore ii toe en we l lt p T oe T NI 4 4 i ERES NI
12. via a standard RJ45 connector See Basic Connections on page 23 for more information 9 www acti com VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 V lt gt ACTI Connecting Vision Hardware Manual Installation Procedures Mount the Camera Using the Bundled Bracket 1 Mark the location of the three 3 screw holes using the bracket plate included in the package NOTE Depending on the surface where you will install the camera it may be necessary to drill the holes and use the supplied screw tox 2 Attach the plate to the surface using the three 3 supplied screws 3 Attach the bracket to the plate 10 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 WA lt gt ACTI Connecting Vision Hardware Manual 4 Depending on how you want to install the camera attach the camera to the bracket through one of the two 2 holes below 5 Adjust the camera viewing angle and tighten the knob to fix the camera position Depending on the camera angle you may also need to tighten the two 2 screws using the star wrench included in the package to fix the camera position 6 Connect an Ethernet cable from the network side to the Ethernet port of the camera to complete the installation See Basic Connections on page 23 for more information Camera Side Network Si
13. 1 11L E 00010 j KCM5611 12G X 00480 KCM7311 12E X 00188 KCM7911 12H X 00466 KCM8111 12K X 00009 th Network 4 111 items VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 WA lt gt ACTI Connecting Vision Hardware Manual By double clicking with the left mouse on the camera model it is possible to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already If you work with our cameras regularly then there is even a better way to discover the cameras in the network by using IP Utility The IP Utility is a light software tool that can not only discover the cameras but also list lots of valuable information such as IP and MAC addresses serial numbers firmware versions etc and allows quick configuration of multiple devices at the same time The IP Utility can be downloaded for free from http www acti com IP Utility With just one click you can launch the IP Utility and there will be an instant report as follows e IP Utility Daa _ p IP Address NetMask 172 16 26 178 255 255 255 0 x Basic Search O Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot Account admin Password 123456 Total 57 E IP Address MAC Address FW Version Model Serial No Multicast IP 172
14. 299 WA lt gt ACTI Connecting Vision Hardware Manual Step 1 Remove the Pre installed Network Cable Pigtail 1 Loosen the three 3 screws to detach the back cover NOTE A cable is connected inside the camera do not abruptly pull the back cover 2 Disconnect the network connector 3 Remove the pre installed cable gland and network cable using a wrench not included in the package 9 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 bia ACT Hardware Manual Step 2 Prepare the Conduit Gland and Flex Conduit 1 Disassemble the bundled conduit gland as shown below Clamping Nut Body Sealing Insert Lock Nut 2 Pullthe Ethernet cable through the flex conduit 3 Insert the clamping nut through the flex conduit F ie VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision gt S Hardware Manual 4 Insert the sealing insert and attach it at the end of the flex conduit Step 3 Install the Ethernet Cable 1 Insert the body A to the back cover and secure it with the lock nut B 2 nsert the Ethernet cable through the back cover and then align the sealing insert to the gland body 7 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax
15. 45 808299 ACTI Connecting Vision gt s Hardware Manual 5 Tighten the sealing nut Make sure the rubber is tightly squeezed to avoid possible water leak Rubber must be squeezed tightly NOTES on using Ethernet cables When replacing the pre installed network cable it is recommended to use exterior grade Ethernet cables CAT5 CAT5e CAT6 ordinary Ethernet cables are only designed for indoor use and may deteriorate quickly when exposed to outdoor elements Exterior grade Ethernet cables are waterproof and do not require a conduit 2 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 pb ACT Hardware Manual Basic Connections To connect the camera you need to prepare the following e Power over Ethernet PoE supported switch to connect multiple cameras or PoE injector to connect a single camera e Ethernet cables Connecting a Single Camera To connect a single camera use a PoE injector to supply both data and power to the camera using one Ethernet cable Follow the procedures below 1 Connect the camera to the PoE injector using an Ethernet cable 2 Connect the PoE injector to the network and an AC power source 3 Connect a PC to the same network Ethernet Cable lt Ethernet Cable Data Power Cable PoE Injector Ethernet Cable Data Power AC Power Source 2v e F Camera 4 After making the connections acc
16. T 1 romers m ha o m m Fae saec i appenaa ok canina pec n canina AEA La ai Xauf OF acit Pw osortnt porc fos Go Cammy adst CL AMAA eon Tho equiprnent bE iiy Rin G cem cem fete T merae gene Cr pearc Acus nos adopts congr Ir Comers AEE bt ond reaa u i ter morene Perey matte hate Thurs pre Dee ney te fetarmome the arat ewhatnatcr tere dm orca ond reprae with AEM the manay indir date Ver Sayeng date fear ACT Un severe q mee zl m protect enims n ACTU fe meret canon dre h f dte of nite free ACT Adfocied anbean m vered by ACT Autore Daries aang naacal feo Mr y Boti Clem peto Qo N TE Fer Wonarty Repereton secas Qo c 19 oi aT oe LU C rea Yu S ri d Focus Lens Tuner 8 www acti com VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTi a 3 Connecting Vision Hardware Manual Physical Description Internal External Reset Button Ethernet Port e Power LED 1 Reset Button Use the Reset Button to reset the camera to its factory default settings While the camera is powered on press and hold the Reset button for 5 seconds or until the Power LED lights up 2 Power LED The Power LED lights up when the camera is connected to the power source and the camera starts the boot up process Then the Power LED goes off when the boot process is complete 3 Ethernet Port Use the Ethernet Port to connect the camera to the Ethernet
17. Use the following IP address IP address 192 168 0 99 Subnet mask VITSE E NE Default gateway I S S IS S S IS Obtain DNS server address automatically wk Link i Uni Layer Topology Discovery Responder Use the following DNS server addresses Install Uninstall Properties Preferred DNS server Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Alternate DNS server E Validate settings upon exit j ok Cancel 7 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision bis Hardware Manual Manually adjust the IP addresses of multiple cameras If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them all of the cameras would then have the initial IP address of 192 168 0 100 which is not a proper situation for network devices all the IP addresses have to be different from each other The easiest way to assign cameras the IP addresses is by using IP Utility TE IP_Utility IP Address NetMask 172 16 26 192 255 255 255 0 z Basic Search z Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp
18. de NOTES on using Ethernet cables For outdoor installations it is recommended to use exterior grade Ethernet cables CAT5 CAT5e CAT6 ordinary Ethernet cables are only designed for indoor use and may deteriorate quickly when exposed to outdoor elements Exterior grade Ethernet cables are waterproof and do not require a conduit i VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 WA lt gt ACTI Connecting Vision Hardware Manual N CAUTION If the camera will be installed outdoors be sure to waterproof the cable connection by enclosing it inside a junction box or wrap it using a moisture sealant tape such as 3M PRODUCTS Core Series 4 1000 not included in the package or equivalent oee example below For other waterproofing methods see Waterproof Cable Installation on page 14 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision vA Hardware Manual Other Mounting Options In areas with fierce weather conditions the light bundled bracket can be replaced by a heavy duty outdoor bracket combined with additional mounting accessories Below are the optional mounting accessories that you can use with the camera Mount Types Accessories Corner Mount Suitable when mounting the camera on a corner wall PAMX 1103 PMAX 0402 Pole Mount Suitable when mounting the came
19. deo product near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like Don t use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions 1 When the power supply cord or plug is damaged 2 If liquid has been spilled or objects have fallen into the video product 3 If the video product has been directly exposed to rain or water 4 Ifthe video product does not operate normally by following the operating Instructions in this manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine if the video product is in proper operating condition 6 www acti com VolPon www voipon co uk sales voipon co
20. equipment Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Trademarks All names used in this manual are probably registered trademarks of respective companies Liability Every reasonable care has been taken during the writing of this manual Please inform your local office if you find any inaccuracies or omissions We cannot be held responsible for any typographical or technical errors and reserve the right to make changes to the product and manuals without prior notice 4 www acti com VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision vA Hardware Manual Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or tel
21. ess the cameras live view to adjust the viewing angle and focus and configure the camera settings according to your preference See Accessing the Camera on page 25 for more information VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 pb ACT Hardware Manual Connecting Multiple Cameras To connect multiple cameras use a PoE switch 1 Connect the camera s to the PoE switch using Ethernet cables 2 Connect the PoE switch to a network and an AC power source 3 Connect a PC to the same network Ethernet Cable Ethernet Cable Data Power Cable PoE Switch i AC Power Ethernet Cables Source Data Power Cameras 4 After making the connections access the cameras live view to adjust the viewing angle and focus and configure the camera settings according to your preference See Accessing the Camera on page 25 for more information 24 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 bia ACT Hardware Manual Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC both the camera and the PC have to be within the same network segment In most cases it means that they both should have very similar IP addresses where only the last number of the IP address is different from each other There are 2 different approaches to IP Address managemen
22. evision reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e HReorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications to the equipment that are not expressly approved by the responsible party for compliance could void the user s authority to operate the equipment European Community Compliance Statement C 4 This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European Standard EN 55022 and EN 55024 In a domestic environment this product may cause radio interference in which cause the user may be required to take adequate measures 5 www acti com VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision vA Hardware Manual Safety Instructions Don t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Water and Moisture Do not use this vi
23. f See full map a A de e A Local Area Connection Ch d d shari 1 ae SISO_NP_PC1 Network Internet Ciera Network Ir This computer GT Intel R 8 y Disable View your active networks Connect or disconnect Status Diagnose Jd Network Access type Internet Work network Connections Local Area Connection y Bridge Connections Create Shortcut Change your networking settings elete us Set up a new connection or network Delete lt z Set up a wireless broadband dial up ad hoc or VPN connection or set up a router or Rename access point z Hy Properties a Connect to a network Connect or reconnect to a wireless wired dial up or VPN network connection See also i HomeGroup Choose homegroup and sharing options Internet Options Access files and printers located on other network computers or change sharing settings Windows Firewall btocol Version 4 TCP IPv4 Properties L jtm E eee ee Connect using amp Intel R 82567LM 3 Gigabit Network Connection You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically This connection uses the following items iv o Client for Microsoft Networks da VirtualBox Bridged Networking Driver QoS Packet Scheduler B File and Printer Sharing for Microsoft Networks
24. ra on a pole PAMX 1103 PMAX 0503 e For more information about the mounting solutions and accessories please check the Mounting Accessory Selector in our website http www acti com mountingselector e he above mounting accessories are not included in the package Contact your sales agents to purchase d VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision vA Hardware Manual Waterproof Cable Installation The camera and the pre installed network cable are resistant to salt water weak acid alcohol oil grease and other common solvents However in areas with fierce weather conditions and those that can easily be flooded ensure that the exposed length of cable is also protected It is recommended to use a flexible conduit with 1 2 diameter and the conduit gland included in the package to protect the camera cabling In this case the pre installed network cable with pigtail female connector must be replaced with a standard Ethernet cable NOTE The flexible conduit and Ethernet cable are not included in the package and must be sold separately When purchasing make sure the flex conduit size is 1 2 to match the bundled conduit gland To do the waterproof cable installation also prepare the following tools e Screwdriver e Wrench 4 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808
25. t in Local Area Networks by DHCP Server or Manually Using DHCP Server to Assign IP Addresses If you have connected the computer and the camera into the network that has a DHCP server running then you do not need to configure the IP addresses at all both the camera and the PC would request a unique IP address from DHCP server automatically In such case the camera will immediately be ready for the access from the PC The user however might not know the IP address of the camera yet It is necessary to know the IP address of the camera in other to be able to access it by using a Web browser The quickest way to discover the cameras in the network is to use the simplest network search built in the Windows system just by pressing the Network icon all the cameras of the local area network will be discovered by Windows thanks to the UPnP function support of our cameras In the example below we successfully found the camera that we had just connected to the network a nAn Organize v Search Active Directory Network and Sharing Center Jr Favorites j D92 A XX 13E 00047 RE Desktop T Downloads E41 A XX 13A 01224 E42 A XX 12K 00027 E42 A XX 12L 00286 E51 A XX 12J 00073 E53 A XX 13A 00089 E73 A XX 13A 00028 ENR2000 ENR KCM3911 12A X 00312 i Recent Places Documents 2 Music t Pictures B Videos aM E a Libraries W A j KCM5311 11B X 00010 i Computer jj KCMS531
26. the IP address since the default HTTP port of the camera is 80 which can be omitted from the address for convenience Web Configurator Account Password Language English x Login Reset Before logging in you need to know the factory default Account and Password of the camera Account Admin Password 123456 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 ACTI Connecting Vision gt s Hardware Manual To check the firmware version through the Web Configurator access the Setup page and click System gt System Info Web Configurator o x E Host Date amp Time Network IF Settings Video Event User Account Factory Default Firmware Upload Save amp Reboot Logout system Information D For further operations please refer to the Firmware User Manual VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299 WA lt gt ACTI Connecting Vision Hardware Manual Other Adjustments and Accessories Adjust the Viewing Angle 1 Open the front cover 2 Attach the lens focus tuner to the lens 3 Adjust the focus of the target area based on the live view of the camera see Accessing the Camera on page 25 4 When done close the front cover CAUTION The front cover must be tightly closed to ensure water or dust does not
27. way to the end 7 Place the connector into the crimping tool and cinch down to secure the RJ 45 connector to the Ethernet cable 8 Repeat the same procedures to attach the other end 34 VolPon www voipon co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1245 808299

Download Pdf Manuals

image

Related Search

Related Contents

Samsung SCX-4833FD Instrukcja obsługi  VarioS®-Microscanner user manual - Scanner    MV-STAT4B INSTALLATION INSTRUCTIONS  EX542i  User Manual - Akutbutiken.se  Benutzerhandbuch  波長分割多重フィルタ - データコントロルズ  

Copyright © All rights reserved.
Failed to retrieve file