www.microhpro.com LEDVIXION/WH User Manual
Contents
1. High light output with 1770LUX 7M one LED High efficiency LED shutter with variable speed Strobe effect with 18 flashes per second and pulse effect 0 100 smooth linear dimmer 8 built in default programs for easy performance 13 30 30 DMX channels switchable in the menu DMX512 master slave and sound activated controllable or auto operation Blue LCD display Efficient low noise fan cooling system Powercon IN OUT as default Two 1 4 turn fastening Omega Clamps 10 Technical Specifications Input Voltage AC90 260V 50 60Hz LED Quantities 4PCS 8W WHITE LEDs Control Signal DMX512 master slave and sound activated or auto operation Control Channel 13 30 30 DMX Channels switchable Power Consumption 107W Dimensions 100 D x1032 W x273 H mm Packing Dimensions 181 D x11633W x313 H mm Net Weight 8kg Gross Weight 10 5kg 11 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be ad2. 063 Shutter open 064 095 Strobe effect from slow to fast 096 127 Shutter open 128 159 Pulse effect in sequences from slow to fast 24 9 24 PAN 4 0 255 PAN 4 movement 25 25 PAN Fine 4 0 255 Fine control of PAN 4 movement 26 10 26 TILT 4 0 255 TILT 4 movement 27 27 TILT Fine 4 0 255 Fine control of TILT 4 movement 0 225 Max to min speed for PAN 4 and TILT 4 226 235 Blackout by movement 28 11 28 Speed 4 236 245 Blackout by all wheel changing 246 255 No function 0 099 No function 100 119 1 120 139 Macro 2 29 12 29 Macro 140 159 Macro 3 160 179 Macro 4 180 199 Macro 5 200 255 Macro 6 0 019 No function 020 029 No function 030 039 No function 040 079 No function 080 099 Motor reset 100 119 nternal program 1 30 13 30 Special 120 139 nternal program 2 140 159 nternal program 3 160 179 nternal program 4 180 199 nternal program 5 200 219 nternal program 6 220 239 nternal program 7 240 255 Internal program 8 9 Key Features 4PCS 8W high power WHITE LEDs 50 000 hours lifespan and low power consumption 4PCS pocket size moving fixture controllable individually Very fast and precise PAN TILT movement 540 PAN and 270 TILT Scan position memory auto reposition after unexpected movement Outstanding white BEAM effect Specific optic system
3. 512 control connections Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX 512 connection with DMX terminator POWER LINK AC 90 260V 50 60Hz CONTROLLER DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket COMMON 1 Ground DMX ee 2 Data 512 OUT DMX512 IN 3 Data SPINKLR J w For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1209 ER 2 3 1 PIN 3 PIN2 6 Menu Operations Function Mode DMX Address A001 AXXX Set to slave Auto Run Internal Program1 8 Master Alone Music Control Internal Program1 8 Master Alone Reset On Off Reverse Pan On Off Reverse Tilt On Off Mic sensitivity 0 99 Special Reset Default On Off Calibration Code Pa
4. MICRO www microhpro com LEDVIXION WH 4 HEAD MINIBEAM User Manual KEEP THIS MANUAL FOR FUTURE NEEDS 1 Unpacking Thank you for choosing the MICROH LED VIXION WH For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs MICROH S LED VIXION WH is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for small to medium live performances theater studio nightclubs and discos LED VIXION WH adopts 4PCS high power 8W White LEDs in 4PCS pocket size moving fixtures in a bar which features high brightness and stability Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box LED VIXION WH One Signal Cable One Omega Clamp Two Power Cable One Safety Chain One User Manual One 2 Safety Instructions CAUTION Be careful with your operations With a dangerous voltag
5. No function 8 3 8 Dimmer 2 0 255 Dimmer 0 100 0 031 Shutter closed 032 063 Shutter open 064 095 Strobe effect from slow to fast 096 127 Shutter open 9 4 9 Shutter 2 128 159 Pulse effect in sequences from slow to fast 160 191 Shutter open 192 223 Random strobe effect from slow to fast 224 255 Shutter open 10 10 PAN 2 0 255 2 movement 11 11 PAN Fine 2 0 255 Fine control of PAN 2 movement 12 12 TILT 2 0 255 TILT 2 movement 13 13 TILT Fine 2 0 255 Fine control of TILT 2 movement 0 225 Max to min speed for PAN 2 and TILT 2 226 235 Blackout by movement 14 14 Speed 2 236 245 Blackout by all wheel changing 246 255 No function 15 15 Dimmer 3 0 255 Dimmer 0 100 0 031 Shutter closed 032 063 Shutter open 16 16 Shutter 3 064 095 Strobe effect from slow to fast 096 127 Shutter open 128 159 Pulse effect in sequences from slow to fast 160 191 Shutter open 192 223 Random strobe effect from slow to fast 224 255 Shutter open 17 17 PAN 3 0 255 PAN 3 movement 18 18 PAN Fine 3 0 255 Fine control of PAN 3 movement 19 19 TILT 3 0 255 TILT 3 movement 20 20 TILT Fine 3 0 255 Fine control of TILT 3 movement 0 225 Max to min speed for PAN 3 and TILT 3 226 235 Blackout by movement 21 21 Speed 3 236 245 Blackout by all wheel changing 246 255 No function 22 22 Dimmer 4 0 255 Dimmer 0 100 0 031 Shutter closed 23 23 Shutter 4 032
6. e you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual gt Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class 1 Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not nece
7. hered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer
8. oints Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The LED VIXION WH provides two unique mounting brackets assembly that integrates the bottom of the base the included Omega Bracket and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the omega bracket As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly Regardless of the rigging option you choose for your LED VIXION WH always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle 5 DMX
9. ssarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 3 Operation Instructions The LED VIXION WH is for beam effect for on site decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make s
10. ssword 088 TILT1 PAN2 TILT2 PANS TILT3 TILT4 Temperature XXX C F Manual Control PAN XXX Edit Program Program1 Steps 1 48 Scenes 01 8 Scenes XX Time xx xS Mode of channel Mode Set 16Bit Mode 8Bit Mode Design Mode Design Mode Set Max Channel XX PAN 001 Version V1 0 V9 9 7 Photometric Data Photometric Beam Angle Data LUX x 0 0929 FC 2 Beam Angle 1LED 7316FC 78750LUX 966FC 10395LUX 322FC 3465LUX 173FC 1859LUX Om Oft 1m 3m 5m 3 28 ft 9 84 ft 16 4 ft 7m 22 96 ft RV 2 Beam Angle 8 DMX Channels Channel Function Value Description 16B 8B DE 1 1 1 Dimmer 1 0 255 Dimmer 0 100 0 031 Shutter closed 032 063 Shutter open 064 095 Strobe effect from slow to fast 096 127 Shutter open 2 2 2 Shutter 1 128 159 Pulse effect in sequences from slow to fast 160 191 Shutter open 192 223 Random strobe effect from slow to fast 224 255 Shutter open 3 3 PAN 1 0 255 PAN 1 movement 4 4 PAN Fine 1 0 255 Fine control of PAN 1 movement 5 5 TILT 1 0 255 TILT 1 movement 6 6 TILT Fine 1 0 255 Fine control of TILT 1 movement 0 225 Max to min speed for PAN 1 and TILT 1 226 235 Blackout by movement 7 7 Speed 1 236 245 Blackout by all wheel changing 246 255
11. ure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 4 Mounting and Installation Cautions For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture from a ceiling or set on a flat level surface see illustration below Be sure this fixture is kept at least 0 5m 1 5 ft away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Mounting p
Download Pdf Manuals
Related Search