CPS 2200 User Manual
Contents
1. and so on In this mode the HOME UPS operating voltage in AC mode is within 190 260Vac with the same output voltage The line sensitivity is higher B Select Wide setting to save energy In this mode the operating range of voltage for the HOME UPS is 100 280Vac Therefore the output voltage will be the same as the MAINS input voltage The HOME UPS unit in this mode has a lower sensitivity with a longer transfer time for switching from AC mode to battery mode in the event of power failure You can safely connect and use home appliances which are not sensitive to transfer time limitations such as florescent tubes bulbs TV etc m AC outlet The HOME UPS provides one outlet for connected equipment to insure temporary uninterrupted operation during a power failure and against surges and spikes N AC Inlet Connect to utility power through the input power cord Functional Test AC Mode The HOME UPS delivers power to the load derived from the utility and maintains proper battery charge On Battery Mode The HOME UPS operates on battery when the utility voltage has fallen outside the limits Local users are alerted to this mode of operation by visual and audible indicators The HOME UPS provides power to the load from the battery and the output voltage of the HOME UPS are regulated within a narrow range 1 Switch On Press the power switch then the status LCD will light up 2 Switch Off Press again the power switch the statu2. not turned on Provide adequate ventilation for the battery compartment The battery enclosure should be designed to prevent accumulation and concentration of hydrogen gas at the top of the compartment 5 Connect the Load DO NOT expose the HOME UPS to rain snow or liquids of any type The HOME UPS is designed for Connect the equipment to the HOME UPS outlet Please make sure that the total loads of your l equipments are less than the maximum total power load of the HOME UPS indoor use only DO NOT obstruct the ventilation openings DO NOT connect neutral of the power distribution box on the wall to BASIC OPERATION a The OUTPUT neutral of HOME UPS FRONT PANEL DESCRIPTION or b The INPUT neutral of equipment E Otherwise the reversed polarity will damage the HOME UPS and the connected equipment Utility power Home UPS Common Neutral S EF CAUTION Risk of electric shock do not remove cover No user serviceable parts inside The battery can energize hazardous live parts inside even when the AC input power is disconnected To avoid electrical shock turn off the HOME UPS and unplug it from the AC power source before servicing the battery Servicing the battery can only be performed by trained personnel 1 LCD Module Display High resolution and intelligent LCD display shows all the HOME UPS information with icons and messages For more information please check the Definitions for Illuminated LCD Indicators sect
3. L Jk 2 Ventilation The location should provide adequate air flow around the HOME UPS with 10 CM minimum clearance on all sides for proper ventilation CPS1200EILCD CPS2200EILCD ee ee 4s User s Manual Connect the external battery with the DC cables ge t from the back of the HOME UPS Follow battery if a pene polarity guide located near battery cables as Batt y oboe fe below NK DN J p i 38888 IMPORTANT SAFETY INFORMATION Red cable for battery positive polarity gt Se e AP a SAVE THESE INSTRUCTIONS Black cable for battery negative polarity i a This manual contains important safety instructions Please read and follow all instructions carefully 4 Connect to AC and Charge the Battery during installation and operation of the unit Read this manual thoroughly before attempting to unpack Connect the HOME UPS to a wall outlet Avoid using extension cords and adapter plugs Charging install or operate the HOME UPS the battery for at least 8 hours is recommended to insure that the battery is fully charged To Insure the wall outlet and HOME UPS are located near the equipment being attached for proper recharge the battery simply leave the unit plugged into a wall outlet To maintain optimal battery accessibility charge leave the HOME UPS plugged into an AC outlet at all times To reduce risk of damage and injury please use batteries with good quality This HOME UPS can be charged even when HOME UPS is
4. SW Overload Vv Illuminated X Not Illuminated _ Either HOME UPS Status PREY 8 Display Capacity Display Digital Value Display _ m Load Battery Input Output Voltage Voltage Initial X VM xX UP Uv E o a ee eaan ee 2 ee eee ee EEE ee ee ee ee ee eee Press gt 3sec souibeaney V Press gt 3sec again X V X Sound Enable i ae e a oe Vv Illuminated X Not Illuminated Battery mode Select SW Press Either Off charging mode Auto bypass HOME UPS Status es Display Capacity Display Digital Value Disp Select SW igital Value Display Press y Load Battery Input Output xX x xX X X X X V Illuminated X Not Illuminated Either Visit www cpsww com for more product information and the nearest CyberPower local contact for your region Entire contents copyright 2012 CyberPower Systems Inc All rights reserved Reproduction in whole or in part without permission is prohibited zZ A
5. The total load that you will be placing on the battery powered outlets should not exceed 80 of the unit s capacity 2 DC Input Cable Red Connect to battery positive polarity 1 DC Input Cable Black Connect to battery negative polarity HARDWARE INSTALLATION GUIDE 3 Input Circuit Breaker Before installation please read and understand the following instructions The circuit breaker provides optimal overload protection 1 Placement The HOME UPS must be installed in a protected environment away from heat emitting appliances such as a radiator or heat register Do not install this product where excessive moisture is present gt Charger Control A Select Default setting for general application The charge voltage is 13 7V 27 4V respectively for CPS1200EI and CPS2200EI B Select Customized setting for special battery condition The charge voltage is 13 3V 26 6V respectively for CPS1200EI and CPS2200El Note Operate by trained professionals ONLY Incorrect operation will damage the battery or Input Voltage Range Selector Input voltage range is defined in specification section Output voltage is the same as input voltage in AC mode A Select Narrow setting for general electrical appliance such as TUBE LIGHT ENERGY SAVING LAMP TV JUICER amp MIXER etc It is not suitable for high power motor or inductive load such as the fridge of 1KW the motor of 800W AIR COOLER having risk of rebooting
6. ion INSTALLING YOUR HOME UPS SYSTEM 2 Power Switch UNPACKING Press the power switch to turn the HOME UPS ON or OFF Inspect the unit upon receipt The box should contain the following 3 LCD Function Selected Switch HOME UPS Unit 1 Power Cord x 1 User Manual x 1 The switch can be used to select the LCD display contents including input output voltage and load percentage etc HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT a REAR PANEL DESCRIPTION 1 Insure that the equipment plugged into the AC outlet does not exceed the HOME UPS unit s rated capacity 1200VA 720W for CPS1200EILCD 2200VA 1320W for CPS2200EILCD If rated unit capacities are exceeded an overload condition may occur and cause the HOME UPS unit to shut down or the circuit breaker trip 2 If the power requirements of your equipment are listed in units other than Volt Amps VA convert Watts W or Amps A into VA by doing the calculations below Note The below equation only calculates the maximum amount of VA that the equipment can use not what is typically used by the equipment at any one time Users should expect usage requirements to be approximately 60 of below value TO ESTIMATE POWER REQUIREMENTS 1 220 Vx Amps A VA 2 Add the totals up for all pieces of equipment and multiply this total by 0 6 to calculate actual requirements There are many factors that can affect the amount of power that your computer system will require
7. me is shortened Overload load Alarm buzzer beeps continuously Charge battery for 8 hours or more Battery voltage is too low If any abnormal situations occur that are not listed above please contact service personnel TECHNICAL SPECIFICATIONS CPS1200EILCD 1200VA 720W Wide mode 100VAC 280VAC Narrow mode 190VAC 260VAC 50 60Hz CPS2200EILCD 2200VA 1320W Capacity VA Capacity Watts Input Voltage Range Frequency Range On Battery Output Voltage On Battery Output Frequency Overload Protection Physical Total of HOME UPS Receptacles Simulated Sine Wave at 220Vac 10 50 60Hz On Utility Circuit Breaker On Battery Internal Current Limiting 1 Shuko FR UK India NEMA UN Maximum Dimensions Weight Battery Lead Acid Battery Warning Diagnostics Indicators Audible Alarms Environmental 265mm L 250cm W 90cm H 2 05 kg 4 5 Lbs 2 2 kg 4 9 Lbs 12V 24V HOME UPS Status Display Low Battery Overload Fault Operating Temperature Operating Relative Humidity 32 F to 104 F 0 C to 40 C 0 to 90 NON CONDENSING Management Auto Charger Auto Restart DEFINITIONS FOR ILLUMINATED LCD INDICATORS LCD Indication LOAD BATT CAP INPUT OUTPUT Som U0 A ox DA t HOME UPS Status a na Display Capacity Display Digital Value Display A Load Battery Input Output Cap Cap Voltage Voltage of Load ae a ee ee ee Line mode Select
8. s LCD will go off 3 Cold Start Start on Battery This HOME UPS can be turned on even when AC is not present Press the power switch then the status LCD will light up ROUTINE MAINTENANCE AND STORAGE ROUTINE MAINTENANCE 1 Use dry soft clothes to clean the panel and plastic parts Do not use any detergent that contains alcoholic ingredient 2 Unplug the HOME UPS from power inlet if the HOME UPS will not operate for long period of time STORAGE 1 First turn off your HOME UPS and disconnect its power cord from the wall outlet Disconnect all cables connected the HOME UPS to avoid battery drain 2 The HOME UPS should be stored in a cool dry location 3 Make sure the battery is fully charged before the HOME UPS is stored 4 For extended storage in moderate climates the battery should be charged for 12 hours every 3 months by plugging the power cord into the wall receptacle and turning on the main switch Repeat it every 2 months in high temperature locations TROUBLE SHOOTING Remedy 1 Battery Weak 1 Re charge battery No LCD display 2 Battery defective 2 Battery replacement 3 Power switch is not 3 Press and hold power pressed switch 1 AC Input missing 1 Check AC input Mains normal but not connection works in AC mode 2 Input protector is effective 2 Reset the input protector Verify that the load Overload matches the capability specified in the specs Remove some non critical Backup ti
Download Pdf Manuals
Related Search