Home

Remote Manual

image

Contents

1. NOTES ON NETWORK MANAGEMENT Add a node group or scene can also be referred to as include a node group or scene Remove a node group or scene can also be referred to as Exclude a node group or scene ADDING A DEVICE NODE LIGHT TO THE NETWORK In order to control the lights they must be Z wave enabled and you must first add them to your home network To add a device to your home network without assigning it to a specific number key perform the following steps 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press ADD once Red LED blinks once 3 Press LIGHT once Red LED blinks once 4 Press LIGHT again Green LED blinks rapidly 5 Press the button on the device so that it sends its information to the remote and receives information from the remote 6 When the green LED blinks twice you have successfully added the device to your home network 7 The device can now be added to Groups and or Scenes NOTE If the red LED emits one long steady blink you have pressed an invalid key or the device has not been successfully added to your home network Please make sure the remote is within two feet of the device and try again ADDING A LIGHT DEVICE NODE TO YOUR REMOTE You can add a maximum of 18 lights to your remote so that they can be controlled individually Adding a device to your remote also adds it to your network If the device number you are trying to add is already associated with
2. another device the previous information is lost To add a device to your remote perform the following steps 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press ADD once Red LED blinks once 3 Press LIGHT once Red LED blinks once 4 Press a digit 1 9 for the device location you wish to add Press SHIFT and the digit 1 9 if you are adding devices 10 through 18 Green LED blinks rapidly 5 Press the button on the device so that it sends its information to the remote and receives information from the remote 6 When the green LED blinks twice you have successfully added the device to your remote control NOTE If the red LED emits one long steady blink you have pressed an invalid key or the device has not been successfully added to your remote Please make sure the remote is within two feet of the device and try again REMOVING AN INDIVIDUAL DEVICE LIGHT NODE FROM YOUR REMOTE 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press REMOVE once Red LED blinks once 3 Press LIGHT once Red LED blinks once 4 Press a digit 1 9 for the device location you wish to remove Press SHIFT and the digit 1 9 if you are removing devices 10 through 18 5 When the green LED blinks twice you have successfully removed the device 4 from your remote control NOTE If the red LED emits one long steady blink you have pressed an invalid key or the device has not been suc
3. emits one long steady blink the information has not been successfully transferred Repeat steps 1 6 if this occurs COPYING NETWORK AND OR DEVICE INFORMATION TO THIS REMOTE This allows a second remote to receive information from the first remote and to become a new primary or secondary remote 12 Place the two remotes near each other Press and hold SETUP until both the red and green LEDs blink twice Enter 9 6 7 on the numeric keypad Put the source remote into programming mode so that it sends its information o the GE SmartHome remote as well as receives information from this remote 5 When the green LED blinks twice you have successfully transferred the information 6 Add devices groups and scenes to the new remote as needed PWN Be NOTE If the red LED emits one long steady blink the information has not been successfully transferred Repeat steps 1 6 if this occurs RECOVERING NETWORK INFORMATION To have your remote recover network information perform the following steps 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Enter 9 6 1 on the numeric keypad 3 When the green LED will blink twice You have successfully recovered network information NOTE If the red LED emits one long steady blink the information has not been successfully recovered Repeat steps 1 3 if this occurs RESETTING YOUR NETWORK You can reset your network to clear all device and Z Wave network
4. steps 1 5 if this occurs Controlling a Group To control a Group perform the following steps 1 Press GROUP once to put the remote into GROUP Control mode Red LED blinks once The remote will stay in this mode until either the Light or Scene mode is activated 2 Press the digit key for the group you wish to control 1 9 Press SHIFT and the digit 1 9 if you are controlling groups 10 through 18 The green LED will blink once NOTE If the red LED emits one long steady blink the remote has not successfully communicated with the devices in the group Repeat steps 1 2 if this occurs SETTING UP SCENES Ascene is a single device or group of devices that can be preset to turn to a previously specified setting for example brightness level Scenes are ideal for task or mood lighting You can set up a maximum of 18 scenes containing up to 32 devices per scene Scenes can include lights from different groups Adding a Light Device Node to a Scene 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press ADD once Red LED blinks once 3 Press SCENE once Red LED blinks once 4 Press a digit 1 9 for the scene you wish to add the device to Press SHIFT and the digit 1 9 if you are adding devices to scenes 10 through 18 Green LED blinks rapidly 7 5 Press the button on the light you are adding Green LED pauses briefly blinks once and then resumes blinking rapidly indicating that the re
5. 2 Press DELETE once Red LED blinks once 3 Press ALL once Green LED blinks rapidly 4 Press the button on the device that you wish to remove from All Control 5 The green LED blinks twice You have successfully deleted the device from All Control NOTE If the red LED emits one long steady blink the device has not been successfully deleted from the group Repeat steps 1 5 if this occurs Adding Devices Lights Nodes to All Control The factory default setting for GE Z Wave devices is to be included in All On and All Off control The following section should only be needed if the device has been deleted from All Control 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press ADD once Red LED blinks once 3 Press ALL once Green LED blinks rapidly 4 Press the button on the device you wish to include 5 When the green LED blinks twice you have successfully added the device to all control NOTE If the red LED emits one long steady blink the device has not been successfully added to the group Repeat steps 1 5 if this occurs NOTES ABOUT COPYING INFORMATION TO OR FROM THE REMOTE CONTROL Create Secondary Controller Primary Controller Shift and Controller Copy Receipt are all methods used in the process of Replication Please refer to the respective sections for Create Secondary Controller Primary Controller Shift and Controller Copy for instructions on how to replicate to and or from the
6. 45600 Wireless Lighting Control Remote Manual e Individual Z Wave devices e Groups e Lighting scenes oe Swany Compatible with all Z WAVE products INTRODUCTION Thank you for purchasing the GE SmartHome Remote Your home control network can include up to 232 Z Wave enabled devices This remote allows you to control up to 18 individual Z Wave devices with one easy to use compact unit You can also set up and control up to 18 groups of lights as well as 18 scenes for task or mood lighting Each group can include up to 232 Z Wave devices and each scene can include up to 32 Z Wave devices Lights can be included in multiple groups Scenes can include lights from different groups Please note The terms Device Node and Light all refer to an individual Z Wave enabled device in your home control network and are interchangeable within the context of these instructions If this remote is used as the primary controller you must use it to create your control network You can use multiple remote controls with your Z Wave lighting control network however only one remote will act as the primary controller The primary controller must be used to add or delete devices lights nodes from your network All other remotes are considered secondary and can be used to create groups and or scenes and control your lighting however secondary remotes cannot add or delete devices from your control network NOTE This pr
7. cessfully removed from your remote control Repeat steps 1 5 if this occurs DELETING A DEVICE LIGHT NODE FROM YOUR NETWORK To reset a device to its factory default you must delete it from the network To delete the device from your network perform the following steps 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press DELETE once Red LED blinks once 3 Press LIGHT once Green LED blinks rapidly 4 Press and release the button on the device so that it sends its information to the remote and receives information from the remote 5 When the green LED blinks twice you have successfully deleted the device from your home network NOTE If the red LED emits one long steady blink you have pressed an invalid key or the device has not been successfully deleted from your home network Repeat steps 1 5 if this occurs CONTROLLING INDIVIDUAL LIGHTS DEVICES NODES You can control a light to turn on or off or change its brightness level The operation of a specific device varies by product Refer to the manual for that device to learn its specific operation 1 Press and release the LIGHT key to put the remote into Individual Light Control mode Red LED blinks once The remote will stay in this mode until either the Group or Scene mode is activated 2 Select the light you want to control Press and release SHIFT to control lights 10 through 18 Turning a Light On or Off e To turn alight
8. e of 65 feet by approximately 25 30 e Brick tile or concrete walls block more of the RF signal than walls made of wooden studs and plasterboard drywall e Wall mounted Z Wave devices installed in metal junction boxes will suffer a significant loss of range approximately 20 25 since the metal box blocks a large part of the RF signal Z Wave enabled For questions devices should never e mail support jascoproducts com be used to supply power to or control or call technichal support at 1 800 654 8483 the On Off status of medical and or life is a trademark of the support equipment General Electric Company and is used under license to Jasco Products Company LLC Z Wave home control networks 10 E Memorial Rd are designed to work properly Oklahoma City OK 73114 alongside 802 11 wireless www jascoproducts com computer networks Bluetooth and i z other 2 4GHz or 5 8GHz devices Made in China Some baby cams wireless video Hecho en China devices and older cordless phones using the 900MHz frequency range 45600 2 JASCO 2009 may cause interference and limit the Z Wave functionality Z Wave is a registered US trademark or Zensys A S
9. git 1 9 if you are deleting scenes 10 through 18 5 When the green LED blinks twice you have successfully deleted the scene from your home network NOTE If the red LED emits one long steady blink you have pressed an invalid key or the scene has not been successfully deleted Repeat steps 1 5 if this occurs CONTROLLING SCENES To control a scene perform the following steps 1 Press SCENE once Red LED blinks once The remote will stay in this mode until either the Light or Group mode is activated 2 Press the digit key for the scene you wish to control 1 9 Press SHIFT and the digit 1 9 if you are controlling scenes 10 through 18 The green LED blinks once NOTE If the red LED emits one long steady blink the remote has not successfully communicated with the devices in the scene Repeat steps 1 2 if this occurs Turning All Devices Lights Nodes On or Off To turn all devices on or off perform the following steps 1 Press ALL once Red LED blinks once 2 Press either ON or OFF Any ON or OFF button can be pressed The green LED blinks once NOTE If the red LED emits one long steady blink you have pressed an invalid key or the All On All Off command was not successful Repeat steps 1 2 if this occurs Deleting Devices Lights Nodes from All Control If desired specific devices can be setup to ignore the All On and All Off commands 1 Press and hold SETUP until both the red and green LEDs blink twice
10. in a hazardous condition For these reasons we recommend the following 1 Assign Z Wave controlled appliances to device numbers 10 18 on the GE remote The likelihood of unintentionally turning on the appliance will be reduced significantly because the Shift button will need to be pressed before pressing device numbers 10 18 2 Z Wave devices controlling appliances should be removed from All control setting Instructions on how to do this are included in the manual for your GE remote 3 Do Not include Z Wave devices in Groups or Scenes if they control appliances 4 Do Not use Z Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended or unintentional or automatic power on control 15 Wireless Range This device complies with the Z Wave standard of open air line of sight transmis sion distances of 65 feet Actual performance in a home depends on the number of walls between the remote controller and the destination device the type of construction and the number of Z Wave enabled devices installed in the control network Every Z Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which help eliminate RF dead spots Things to consider regarding RF range e Each wall or obstacle i e refrigerator big screen TV etc between the remote and the destination device will reduce the maximum rang
11. information To reset your network perform the following steps 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Enter 9 6 9 on the numeric keypad 3 When the green LED blinks twice you have successfully reset network information 4 Reset all individual devices as instructed in the section on deleting devices from the network NOTE If the red LED emits one long steady blink the network has not been successfully reset Repeat steps 1 3 if this occurs 13 FCC NOTICE This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off or on the user should e Relocate or reorient the TV or radio antenna e Increase the separation between the device and the receiver Any changes or modifications to the equipment without JASCO s express consent will void the user s right to operate this equipment FCC ID MG345600 WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase This warranty is limited to the repair or replacement of this product only and does not extend to co
12. mote is pending the setup of the bright dim setting on the device 6 Adjust the brightness level on the device within 30 seconds refer to the manual for the device 7 Press SCENE The green LED stops blinking 8 When the green LED blinks twice you have successfully added the device to a scene NOTE If the red LED emits one long steady blink you have pressed an invalid key or the device has not been successfully added to the scene Repeat steps 1 7 if this occurs Removing a Light Device Node from a Scene 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press REMOVE once Red LED blinks once 3 Press SCENE once Red LED blinks once 4 Press a digit 1 9 for the scene you wish to remove the device from Press SHIFT and the digit 1 9 if you are removing devices from scenes 10 through 18 Green LED blinks rapidly 5 Press the button on the device that you wish to remove 6 When the green LED blinks twice you have successfully removed the device from the scene NOTE If the red LED emits one long steady blink you have pressed an invalid key or the device has not been successfully removed from the scene Repeat steps 1 6 if this occurs Deleting a Scene 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press DELETE once Red LED blinks once 3 Press SCENE once Red LED blinks once 4 Press a digit 1 9 for the scene you wish to delete Press SHIFT and the di
13. nsequential or incidental damage to other products that may be used with this product This warranty is in lieu of all other warranties expressed or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state If the unit should prove defective within the warranty period return prepaid with dated proof of purchase to JASCO Products Company 10 E Memorial Rd Oklahoma City OK 73114 14 Compliance with IC Rules AND Regulations IC 6924A 45600 Jasco Products Company Model 45600 Object is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device WARNING e RISK OF FIRE e RISK OF ELECTRICAL SHOCK e RISK OF BURNS Exercise extreme caution when using Z Wave devices to control appliances Operation of the Z Wave device may be in a different room than the controlled appliance also an unintentional activation may occur if the wrong button on the remote is pressed Z Wave devices may automatically be powered on due to timed event programming Depending upon the appliance these unattended or unintentional operations could possibly result
14. oduct can be operated in one Z Wave network with Z Wave certified devices from other manufacturers and or other applications The different listening nodes within the network can act as repeaters regardless of vendor For best results please read and perform all the remaining instructions before using the remote Keep this guide for future reference INSTALLING BATTERIES Three AAA Alkaline batteries not included are required CAUTION Battery Use And Safety e Use only fresh batteries of the required size and recommended type e Do not mix old and new batteries or different types of batteries e If you do not plan to use the remote for an extended period remove the batteries They can leak chemicals that can destroy electronic parts e Dispose of old batteries promptly and properly Do not burn or bury them To Install Batteries 1 Open the battery compartment cover located on the back of the remote 2 Note the and polarity symbols inside the battery compartment 3 Insert the batteries making sure their polarity matches the symbols in the compartment 4 Replace the cover NOTE When the red LED blinks 5 times after a key press you must replace the batteries The remote retains all its user settings while replacing the batteries NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT Z Wave enabled devices should never be used to supply power to or control the On Off status of medical and or life support equipment
15. on press and release the ON key for less than one second The green LED will blink once e To turn alight off press and release the OFF key for less than one second The green LED will blink once Setting a Light s Brightness Level e To make a light brighter press and hold the ON key for more than one second Green LED blinks rapidly 5 eTo dim the light press and hold the OFF key for more than one second Green LED blinks rapidly NOTE If the red LED emits one long steady blink the remote has not successfully communicated with the device Repeat steps 1 2 if this occurs SETTING UP AND CONTROLLING A GROUP You can create a collection of devices lights nodes that you can control as a group You can set up a maximum of 18 groups Each group can contain up to 232 devices Adding a Device Light Node to a Group To add a device to a group perform the following steps 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press ADD once Red LED blinks once 3 Press GROUP once Red LED blinks once 4 Press a digit 1 9 for the group you wish to add the device to Press SHIFT and the digit 1 9 if you are adding a devices to groups 10 through 18 Green LED blinks rapidly 5 Press the button on the device so that it sends its information to the remote and receives information from the remote 6 When the green LED blinks twice you have successfully added the device to your group NOTE If
16. ormation to a secondary remote perform the following steps 1 Place the two remotes near each other 2 Press and hold SETUP until both the red and green LEDs blink twice 3 Enter 9 6 6 2 on the numeric keypad 4 Put the target secondary remote into programming mode so that it sends its information to the primary remote as well as receives information from the remote The primary remote then copies the network information to the new secondary remote Refer to the user manual for the secondary remote for more information 5 When the green LED blinks twice you have successfully transferred the information 6 Add devices groups and scenes to the new secondary remote as needed NOTE If the red LED emits one long steady blink the information has not been successfully transferred Repeat steps 1 5 if this occurs PRIMARY CONTROLLER SHIFT TRANSFER You can transfer all of your remote s information to another remote so it becomes the new primary remote You can do this in two ways either transferring all information or just transferring network information Transferring All Network and Remote Information 1 Place the two remotes near each other 2 Press and hold SETUP until both the red and green LEDs blink twice 3 Enter 9 6 8 1 on the numeric keypad 4 Put the target new primary remote into programming mode so that it sends its information to the source old primary remote as well as receive information 11 f
17. remote CREATE SECONDARY CONTROLLER SENDING DEVICE AND NETWORK INFORMATION TO A SECONDARY REMOTE You can add a secondary remote to your network and copy your primary remote s device and network information to it To send device and network information to a secondary remote perform the following steps 1 Place the two remotes near each other 2 Press and hold SETUP on the primary GE SmartHome remote until both the red and green LEDs blink twice 3 Enter 9 6 6 1 on the numeric keypad Either on off 4 Refer to the user manual for the secondary remote for programming information See the following section on Copying Network Device Information if the target remote is a GE SmartHome remote Put the target secondary remote into programming mode so that it sends its information to the primary remote as well as receives information from that remote The primary remote then copies the network and device information to the new secondary remote 5 When the green LED blinks twice you have successfully transferred the information 10 6 Add devices groups and scenes to the new secondary remote as needed NOTE If the red LED emits one long steady blink the information has not been successfully transferred Repeat steps 1 5 if this occurs SENDING NETWORK INFORMATION TO A SECONDARY REMOTE You can add a secondary remote to your network and transfer your primary remote s network information to it To transfer network inf
18. rom the old primary remote The source remote then transfers the network and device information to the new primary remote Refer to the user manual for the new primary remote for more information 5 When the green LED blinks twice you have successfully transferred the information 6 The source remote is converted into a secondary remote and can not be used to add or delete devices from the network 7 Add devices groups and scenes to the new primary remote as needed NOTE If the red LED emits one long steady blink the information has not been successfully transferred Repeat steps 1 6 if this occurs Transferring Only Network Information 1 Place the two remotes near each other 2 Press and hold SETUP until both the red and green LEDs blink twice 3 Enter 9 6 8 2 on the numeric keypad 4 Put the target new primary remote into programming mode so that it sends its information to the source old primary remote as well as receive information from the old primary remote The source remote then transfers the network information to the new primary remote Refer to the user manual for the new primary remote for more information 5 When the green LED blinks twice you have successfully transferred the information 6 The source remote is converted into a secondary remote and can not be used to add or delete devices from the network 7 Add devices groups and scenes to the new primary remote as needed NOTE If the red LED
19. the red LED emits one long steady blink you have pressed an invalid key or the device has not been successfully added to your group Repeat steps 1 6 if this occurs Removing a Device Light Node from a Group 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press REMOVE once Red LED blinks once 3 Press GROUP once Red LED blinks once 4 Press a digit 1 9 for the group you wish to remove the device from Press SHIFT and the digit 1 9 if you are removing a device from groups 10 through 18 Green LED blinks rapidly 5 Press the button on the device you wish to remove 6 When the green LED blinks twice you have successfully removed the device from your group NOTE If the red LED emits one long steady blink you have pressed an invalid key or the device has not been successfully removed from your group Repeat steps 1 6 if this occurs Deleting a Group 1 Press and hold SETUP until both the red and green LEDs blink twice 2 Press DELETE once Red LED blinks once 3 Press GROUP once Red LED blinks once 4 Press a digit 1 9 for the group you wish to delete Press Shift and the digit 1 9 if you are deleting groups 10 through 18 5 When the green LED blinks twice you have successfully deleted the group from your home network NOTE If the red LED emits one long steady blink you have pressed an invalid key or the group has not been successfully removed from your home network Repeat

Download Pdf Manuals

image

Related Search

Related Contents

DP-3510/4510/6010 Operating Instructions  マレッター基本型 取扱説明書  Page 1 Page 2 Manuale dl istruzioni per I`uso e la manuten  MC68306UMAD2_AD MC68306 Integrated EC000 Processor  Lightolier Work Light MHCR User's Manual  サンファーニ (ティオ・プラス)  RTM-T User Guide - D  USB-1208LS User's Guide - from Measurement Computing  GUIA DEL USUARIO - COMM-CAR  Studio Installation & User Instructions  

Copyright © All rights reserved.
Failed to retrieve file