RAM-6021 Wired Router
Contents
1. red lpn RAM 6021 Wired Router Quick Start Guide amp Hardware Guide November 2013 Quick Start Guide UNPACKING INSTRUCTIONS EN Unpack the Red Lion unit and verify the following components are enclosed for the RAM 6021 Router RAM 6021 amp CD Sixnet Series red l on RAM 6021 H RS232 ROUTER A j je Os RS232 mO Ow L LAN4 LAN LAN2 LANT 2 There are 2 methods to provide power to the router e 4 pin screw terminal e Side mounted 2 5mm barrel connector The modem requires a power source between 8 and 30 VDC to operate Label Color Description GND Black Ground PWR Red Power 8 to 30 VDC 500mMA 12VDC IN White Future feature not supported OUT Green Future feature not supported FEM Connect to the Ethernet RJ45 port for network connectivity ACCESSSING THE WEB USER INTERFACE EN Connect PC to the RAM 6021 Router Connect a CAT 5 Ethernet cable between the local PC and the units Ethernet port Verify that the green LED is lit H Setup PC IP Address For assistance with configuring your PC see the appropriate Microsoft Windows support webpage listed at http support microsoft com PC to Ethernet Interfaces Select Use the following IP address and fill in the blank fields with the information below Ethernet 0 IP address 192 168 02 Subnet mask 255 255 255 0 Default gateway 192 168 0 1 Preferred DNS 192 168 0 1 CONNECT MONITOR CONTR2. input voltage is below 4 VDC Testing the power connection Check the PWR light on the router if it is turned on then the router is powered If its off then review the installation procedures or contact Red Lion Technical Support for further assistance CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved 12
3. 8 30 Vdc nominal Input current max 150mA See Table 6 Operating Temp 40 to 85 C 40 to 185 F Shock IEC 60068 2 27 Vibration IEC60068 2 6 Humidity 5 to 95 non condensing MTBF RAM 6021 1 832K Hours GB 40 C per MIL HNDBK 217F2 Hazardous Locations Class Div 2 Groups A B C D ANSI ISA12 12 01 Electrical Safety UL508 CSA22 2 14 CUL EMC FCC part 15 and Industry Canada ICES 003 CE RoHS CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved RAM 6021 Router Hardware Guide 1 1 2 Mechanical specifications RAM 6021 2 00 13 21cm 4 70 11 84cm 1 00 2 54em 3 77 Drill guide Power 12 serow I9 58emI for direct panel ONO COW Se mounting Jack 8 screw add 6 serew A A T f Panel mounting cars accept up to a SI 12 screw see drill guide to right Dil Serew block l TETE eu 2 3 6666 i5 97cml D z N For 39mm re N N m m O oi a wees IENLOOZ2I POND 2 70 ep 11 94em Removable DIN clip for ee a direct panel mounting t z z optional on some modets 5 g AD OON 5 87em m Se a gt CS WE es SaaS Gw Ep _ 0 39 4 79cm 4 79cm 10 99em CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved RAM 6021 Router Hardware Guide 1 1 3 Power specifications and consumption Power is supplied to the router via d pin screw terminal m Side mounted DC 2 5mm barrel connector router 4 pin Screw Terminal Power i
4. 2 0 Device interface on a Mini B connector It offers Ethernet over USB functionality using the RNDIS driver for Windows XP and Windows Vista Operating systems only The BlueTree RNDIS driver must be installed before the USB interface can be used The driver and instructions can be obtained at www redlion net 1 1 5 3 Serial Port DB9 The router s serial port is an RS232 DCE compliant with EIA 232 standard The connector used is DB9 female and is shown in the illustration below Figure 1 Serial connector looking at front of router CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved 9 RAM 6021 Router Hardware Guide For further serial wiring information refer to the Hardware Installation section 1 1 6 RESET button functions Mode Hard reset Factory restore FW upgrade USB pass through Table 8 Reset button functions Press and hold for less than 3 Standard reboot seconds Press and hold between 3 and To restore default settings for older 10 seconds versions rerun the SN Reflashing RS232 LED flashes quickly procedure found at www redlion net Puts the router in advanced firmware Press and hold between 10 and upgrade mode by restarting the router and 15 seconds running the boot loader only Do not use WAN LED flashes quickly this mode unless instructed to by Red Lion Technical Support Puts the router in main pass through mode Press and hold for longer than 15 to the RF module allowing
5. CCT seconds provisioning and PST support Do not use Signal LED flashes quickly this mode unless instructed to by Red Lion Technical Support CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved 10 RAM 6021 Router Hardware Guide 2 Hardware Installation 2 1 Mounting the RAM 6021 wired router There are 3 different ways to mount a RAM 6021 wired router Horizontally using two 6 screws pan or fillister head onto its horizontal mounting feet Vertically using two 6 screws pan or fillister head onto its vertical mounting feet Vertically using a DIN rail clip 2 2 Ethernet cable If you are connecting to the router via the Ethernet port you will need a straight or crossover category 5 cable with two 8 pin RJ45 connectors on each end To visually confirm that Ethernet cabling was done properly check the LED indication on the Ethernet port located at the rear panel of the router The Link LED should be on when the right cable is used 2 3 USB cable This is an Ethernet over USB connection which behaves like an Ethernet connection It can only be connected to a PC with Windows XP or Windows Vista installed If you are connecting to the router via the USB port you will need a Type A plug to Type B plug USB cable for the mini Type B plug to Type A plug for the RAM 6021 wired router In order for the USB connection to work you need to install the Sixnet USB driver which is available at www redlion net 2 4 Serial cabl
6. IDC 500mMADC Vce 750mVDC Absolute Maximum VDC 30VDC open circuit Absolute Minimum VDC 0 4VDC open circuit 1x Digital Input DIN Configuration un isolated level detection reference to ground Active level 1 6VDC to 30VDC Inactive level OVDC to 1 3VDG Absolute Minimum VDC 0 3VDC Absolute Maximum VDC 33VDC Leakage IDC at 5VDC 150uADC 1x Analog Input Shared with Digital Input DIN AI1 Configuration un isolated input reference to ground Resolution 1024 ADC 10 bit VDC per step 4 8875855mVDC Full scale level 5VDC Zero level OVDC Absolute Minimum VDC 0 3VDC Absolute Maximum VDC 8 3VDC Leakage IDC at 5VDC 265 96uADC TYPE Router view Sixnet Series red l on RAM 6021 A GE e dP RS232 ROUTER Kat Tel CO dzee RS232 PWO Ow Wired Router RAM 6021 CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved 8 RAM 6021 Router Hardware Guide 1 1 4 Indicators Lights LED Table 7 LEDs EE IERE Depending on Serial Application 1 1 5 Data Interface Specifications Serial Ethernet amp USB 1 1 5 1 Ethernet Port The router s 10 100Mbps Ethernet port is compliant with the EIA 568 standard The router s ports are autosensing so they can be used with either a straight or crossover RJ45 cable to connect to host ports The RAM 6021 Router features a 5 port Ethernet switch allowing connectivity to multiple local devices 1 1 5 2 USB Device Port This is a USB
7. OL EN Access Web User Interface Open a web browser amp enter the following in the address bar http 192 168 0 1 10000 newgau html LOGIN INSTRUCTIONS e User Name admin lowercase letters e For Password last six digits of the unit serial number Upon successfully logging in the Web UI will launch Note For security purposes it is recommended that the admin password be changed according to your internal policies To change your password please go to Admin gt Access Settings Figure B Web UI sede System Information Device Model Number SN 6021 Device Serial Number Serial Number 000 Installed Firmware Version SN Version xxxx Current System Uptime 13D 23H 11M 1S Physical Interface Status Interface Name Connection State P Address Link Status Copyright 2013 Red Lion Controls Inc Al Rights Reserved You are now connected to the Web interface If you should see anything other than the screen shown above please refer to the RAM 6021 User Manual located at www redlion net For more information to set up Modbus features please refer to the RAM 6021 User Guide available at www redlion net RED LION CONTROLS TECHNICAL SUPPORT If you have followed all of the instructions up to this point have Satisfied yourself that you are not having an authentication problem are convinced that you have sufficient reception and your unit is still not communicating then it is time to contact Red Lion Technical Support at s
8. e The router has all its serial port pins enabled If all the pins are enabled on the attached serial device it is important to know whether the device is using DIE or DCE as a communication mode The router is a DCE device so use a straight through serial cable between the router and a DIE device such as a terminal Use a NULL router cable adapter between the router and a DCE device such as another router If using custom wiring or if some pins are disabled follow the guidelines below The wiring will vary depending on whether the attached serial device is a DTE or DCE Modem DIE Modem DCE CTS ED CTS CTS RTS RTS ED RTS RTS ED CTS DTR CA DTR DTR ED DSR DSR EI DSR DSR ED DTR Tx EE Tx TX ED RX Ka 4 Rx RA EA TX DCD gt DCD DCD ES DED GND gt GND GND EA GND RI CA RI RI CA RI CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved 11 RAM 6021 Router Hardware Guide 2 5 Power source IMPORTANT Any installations involving electrical wiring and connections should be done by someone who is experienced in this field As described in the Power specifications and consumption section the router can be powered using d pin screw terminal m Side mounted 2 5mm barrel connector WARNING DC 2 5mm Barrel Connector shall not be used in hazardous locations Powering up the router The router will power up as soon as an 8 to 30 VDC voltage is applied to one of its power inputs and shuts off when this
9. ee ee ee ee Ee ee ee 7 1 1 4 Jnai ators LIQIS LEL sessies ses Es ek een ae ge vd ee Ga eg el ee Ge RA E ne Ri aa eer EE eN ee oe IE N n Gede ee ed 9 1 1 5 Data Interface Specifications Serial Ethernet amp USB ie ee ee ee EE Ee ee Ee ee Ee eek ee ee ee ee ee ee ee eek ee 9 LLG BESET DUO TMI CHONG E 10 2 Hardware Installation TE 11 2 1 Mounting the RAM 6021 wired routeF esse esse ee ee ee ee ee RE ee ee ee ee ee ee ee ee ee RR ee ee ee ee ee 11 2 2 dig RE dere AE RI E EE IE EA OE OE EE EE N OE ON EE 11 2 3 ES Ede NE AA OO N VEE ER EE ON OE OE EN DE OE OON EN OO NA DEE 11 EEN Rer ei EE EE OE OE OE OE TE 11 2 5 See Et e E 12 POWETIAG Up Ne de OE OE EE OE EE OR EE EO dant 12 Testing the power connection EE EE EE AE EE EE RE Ee ee AE Ee ee AE RE ee ee Ee ee ee Ee ee ee RE ee ee Ee ee ee EE ee ee RE ee see Ee ee ee RE ee ee RE ee 12 CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved 1 Product Overview 1 1 Specifications RAM 6021 Router Hardware Guide 1 1 1 General specifications Serial interface USB interface LED indicators Dimensions Weight Power Input Power consumption Environmental Certification Table 1 General specifications 1x RS 232 Serial DB9 115200bps 1x USB 2 0 mini configuration port Power WAN RS232 Ethernet Link amp Activity Steel 120 x 96 x 51 mm 4 7 x 3 77 x 2 0 544 g 1 2 bei 4 pin screw terminal Side mounted 2 5 mm barrel connector
10. s supplied to the router via the 4 pin Screw Terminal on the front panel for the RAM 6021 router The pins are described as follows Table 4 4 pin screw terminal Pin Name Description 1 GND Ground 2 PWR Power supply input 8 to 30 VDC 500mA 12VDC 3 OUT Digital output Power connector 4 IN Digital and analog input facing front DC 2 5mm Barrel Connector Power is supplied to the router via the barrel connector on the left side of the RAM 6021 router The contacts are described as follows Table 5 DC 2 5mm Barrel adapter Pin Name Description Sleeve GND Ground Tip PWR Power supply input 8 to 30 VDC KE Power connector facing leit side WARNING DC 2 5mm Barrel Connector shall not be used in hazardous locations Power specification Power input to the router is protected against reverse polarity and over voltage The router s power consumption is as follows Table 6 Power consumption Draw in mA at 12 VDC Standby Transmitting RAM 6021 115 360 CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved 7 RAM 6021 Router Hardware Guide Wiring instructions are provided in the Hardware Installation section All routers are equipped with protection for reversed polarity and power surges over 33 volts The routers are equipped with an internal 3 Amp fuse Electrical Specifications and Pinout 1x Digital Output DOUT Configuration Open Collector reference to ground Absolute Maximum
11. the warranty we will notify you of the repair charges and not repair the IndustrialPro Router without your permission Repairs are guaranteed for 90 days or the remainder of the warranty whichever is longer Buyer s remedies for breach of warranty shall be limited to repair or replacement subject to adjustment as stated herein or full or partial adjustment to purchase price The Red Lion Industrial Pro Router is provided with the following warranty Hardware maintenance and repair is available on a return to factory basis After this initial period configuration assistance will continue to be available on a chargeable basis Software support does not provide for custom code Custom changes are available as a chargeable option The warranty only covers items with a serial number Cables and adapters are not covered For complete and most up to date warranty information go to www redlion net Notice UL Listed as BT 6xxx model CONNECT MONITOR CONTROL 2013 Sixnet Inc All Rights Reserved 3 RAM 6021 Router Hardware Guide TABLE OF CONTENTS CSTR SESE CS MA ONE OE EE OE N EE OO EE EE ER EN 2 UNPACKING IN an CB et el LE 2 d Product OV CIV OW sori ees EA EO N GE Ge Ge GE N GO ER E N We AA oe oe ee 5 dd SPECIE ION AO EO Ee N ON NE EE RE EO EE EE EE EE 5 1 1 1 General spechicatons N nn erenne 5 1 1 2 Mechanical specifications HAM GU 6 1 1 3 Power SPECIFICATIONS and consumpUHON ee Re RA EE ee ee ee RE Ee ee ee ARE Ee ee ee ee ee ee ee ee
12. upport redlion net or 1 877 432 9908 and we will be happy to assist you in getting your unit operational HARDWARE STATUS LEDS LED State Description Power ON Power is applied to the router WAN ON Link established but no data activity FLASH Data transmitted received on network RS232 ON Link established with serial device but no data activity FLASH Data transmitted received with attached serial device Ethernet ON Link established with Ethernet device 2013 Sixnet Inc All Rights Reserved 2 SOFTWARE LICENSING TERMS amp CONDITIONS Software supplied with each Red Lion product remains the exclusive property of Red Lion Controls Red Lion grants with each unit a perpetual license to use this software with the express limitation that the software may not be copied or used in any other product for any purpose It may not be reverse engineered or used for any other purpose other than in and with the computer hardware sold by Red Lion WARRANTY Red Lion Controls provides a limited hardware warranty for the Industrial Pro Router which consists of the following This warranty is effective for three years from the delivery date of the IndustrialPro Router to the purchaser The purchaser is responsible for returning the defective unit to our factory freight prepaid If the IndustrialPro Router is under warranty Red Lion will repair it and return it freight prepaid via standard shipping If the IndustrialPro Router is not covered by
Download Pdf Manuals
Related Search