Home
T2684 - Mattel
Contents
1. i upright position The restraint belts must be adjusted to fit your child snugly The tray is not designed to hold the child in the chair e Only use as a high chair when child is capable of sitting up unassisted e Never leave child unattended 1 FRONT VIEW e Fit the tray onto the seat armrests Slide the tray into place Release Button Ga e While pushing the release button on the front of the tray adjust the tray forward or backward 14 High Chair Use a Tray Insert oil z N 5 SIDE VIEW Adjust Seat Position e Fit the tray insert into the tray as shown e Lift the lever on the back of the seat back and push the seat back forward or pull it backwards to insert the tabs into the desired set Hint The tray insert is not microwave safe e To remove the tray insert place your finger in the notch and lift of slots Use the front slots for the upright position and the back slots for the recline position e Release the lever to secure the tabs in the desired set of slots e Push the seat back to be sure it is latched in position r mm Release Button de an a Y ds WE y Y e While pushing the release button on the front of the tray pull the tray towards you and remove 15 High Chair Use Power Switch Sound Select Buttons 6 SIDE VIEW Adjust Seat Height e While pressing the lever on each seat height adjuster lift or lower the
2. SS T2684 Fisher Price 2 High Chair www fisher price com Consumer Information Swing e Weight limit 25 lbs 11 3 kg e If your child weighs less than 25 Ibs 11 3 kg but is really active and appears to be able to climb out of the swing immediately discontinue its use WARNING To prevent injury or death from falls and being strangled in the restraint system e Always use the restraint system Never use the tray to restrain child e Never use with an active child who may be able to climb out of the swing e Never leave child unattended e Never convert to high chair with child in product High Chair e Weight limit 50 Ibs 22 6 kg WARNING Prevent serious injury or death from falls or sliding out e The child should be secured in the high chair at all times by the restraint system either in the reclining or upright position The restraint belts must be adjusted to fit your child snugly The tray is not designed to hold the child in the chair e Only use as a high chair when child is capable of sitting up unassisted e Never leave child unattended e Never convert to swing with child in product Consumer Information CAUTION This package contains small parts in its unassembled state For adult assembly only e IMPORTANT Please keep these instructions for future reference e Please read these instructions before assembly and use of this product e Adult assembly is required e Tools requ
3. Ave Mara C C Macaracuay Plaza Torre B Piso 8 Colinas de la California Caracas 1071 ARGENTINA Mattel Argentina S A Curupayt 1186 1607 Villa Adelina Buenos Aires COLOMBIA Mattel Colombia S A calle 123 7 07 P 5 Bogot PRINTED IN CHINA IMPRIM EN CHINE T2864pr 0920
4. C Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation ICES 003 This Class B digital apparatus complies with Canadian ICES 003 Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NMB 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada L utilisation de ce dispositif est autoris e seule ment aux conditions suivantes 1 il ne doit pas produire de brouillage et 2 Putilisateur du dispositif doit tre pr t a accepter tout brouillage radio lectrique recu m me si ce brouillage est susceptible de compromettre le fonctionnement du dispositif Parts IMPORTANT Please remove all parts from the package and identify them before assembly Some parts may be packed in the pad 2 Feet 2 Upper Frame Tubes Frame Left and Right Left and Right 2 Seat Tubes Seat Bottom Seat Back Left and Right Hinge Rod Tray Tray Insert Allen Wrench Note Tighten or loosen all screws with the Allen wrench or a Phillips screwdriver Do not over tighten y o O M5 x 38 5 mm Screw 2 M4 5 x 12 mm Screw 3 M5 x 32 mm Screw 2 M3 5 x 25 mm Washer Head Screw 2 Al
5. Swing motion setting e Give the seat a light push to start the swinging motion Hints After turning on power this product may not swing unless there is a child in the seat As with most battery power swings a heavier child will reduce the amount of swinging motion on all settings In most cases the low setting works best for a smaller child while the higher setting works best for a heavier child If swinging stops while using a lower setting try a higher setting Give the seat a light push to start the swinging motion again e Press the sound select buttons for music and other soothing sounds e Press the volume buttons to adjust the volume level e When finished slide the power switch OFF O 18 Upper Frame Tube Upper Frame Frame Tube Release Button 1 BACK VIEW e While holding the upper frame tubes press the frame release buttons 2 SIDE VIEW e Slowly and carefully lower the upper frame towards the floor 19 Care e The restraint system frame and trays may be wiped clean using a mild cleaning solution and a damp cloth e The tray insert is also top rack dishwasher safe or use bottom rack without using the drying cycle e The pad is machine washable Wash in cold water on the gentle cycle Do not use bleach Tumble dry separately on low heat and remove promptly To remove the pad e Remove the elastic loops from the pegs on the underside and back of the seat e Unfasten th
6. d end of the waist belt up through the buckle to form a loop Pull the free end of the waist belt Repeat this e Place your child in the seat Position the crotch belt between procedure to tighten the other waist belt your child s legs To loosen the waist belts e Slide the ends of the shoulder belts onto the ends of the e Feed the free end of the waist belt up through the buckle to form a waist belts loop Enlarge the loop by pulling on the end of the loop toward e Fasten both waist shoulder belts to each side of the crotch belt the buckle Pull the anchored end of the waist belt to shorten the Make sure you hear a click on both sides free end of the waist belt Repeat this procedure to loosen the e Check to be sure the restraint system is securely attached other waist belt by pulling it away from your child The restraint system should remain attached 4 TIGHTEN LOOSEN To tighten the shoulder belts e Hold the adjuster and pull the front shoulder strap down To loosen the shoulder belts e Slide the adjuster down e Tighten each waist belt and shoulder belt so that the restraint system is snug against your child Please refer to the next section for instructions to tighten the belts 11 Changing Shoulder Belt Slots Upper Slots Shoulder Belt Shoulder Belt Lower Slots e Use the lower shoulder belt slots for a smaller child and the upper shoulder belt slots for a larger child FRONT VIEW e From
7. e pad hooks from the front edge of the seat e Pull the restraint belts through the slots in the pad e Lift the top of the pad off of the seat back e To replace the pad refer to the assembly section of these instructions IMPORTANT Never use this product without the restraint system CONSUMER ASSISTANCE AYUDA AL CONSUMIDOR SERVICE LA CLIENTELE 1 800 432 5437 US Canada service fisher price com Fisher Price Inc 636 Girard Avenue East Aurora NY 14052 Hearing impaired consumers Clientes con problemas auditivos Pour les malentendants 1 800 382 7470 En M xico 59 05 51 00 Ext 5205 6 01 800 463 59 89 CANADA Mattel Canada Inc 6155 Freemont Blvd Mississauga Ontario LOR 3W2 www service mattel com MEXICO Importado y distribuido por Mattel de M xico S A de C V Insurgentes Sur 3579 Torre 3 Oficina 601 Col Tlalpan Delegaci n Tlalpan C P 14020 M xico D F R F C MME 920701 NB3 CHILE Mattel Chile S A Avenida Am rico Vespucio 501 B Quilicura Santiago Chile Fisher Price Inc a subsidiary of Mattel Inc East Aurora New York 14052 U S A 2010 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc Fisher Price Inc une filiale de Mattel Inc East Aurora New York 14052 U 2010 Mattel Inc Tous droits r serv s O et d signent des marques de Mattel Inc aux E U VENEZUELA Mattel de Venezuela C A RIF J301596439
8. ired for assembly Phillips screwdriver not included and Allen wrench included e Requires four D LR20 alkaline batteries for swing operation sounds and music Batteries not included e Product features and decoration may vary from photographs FCC Statement United States Only This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Consult the dealer or an experienced radio TV technician for help Note Changes or modifications not expressly approved by the manu facturer responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FC
9. l Shown Actual Size Assembly IMPORTANT Before assembly and each use inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Fisher Price for replacement parts and instructions if needed Never substitute parts Front Tube Rear Tubes 4 Front e Tube Y BOTTOM VIEW pr j 1 i Frame e Lift the rear and front tubes to open the frame 3 ve i mu amas FI u z se mm k 1 s Siena fa Po o TT easa ib 2 M4 5 x 12 mm Screws e Insert an M4 5 x 12 mm screw into the hole in the underside of each foot and tighten with a Phillips screwdriver Upper Frame Tube Hubs 2 TOP VIEW e Fit a foot onto the end of each base tube as shown Hint Make sure the feet curve outward e Position the upper frame tubes so that the hubs face each other e Fit the upper frame tubes into the rear frame tubes Hint The upper frame tubes are designed to fit one way If they do not seem to fit turn them around and try again Assembly Seat Back Tabs M5 x 38 5 mm Screw M5 x 38 5 mm Screw e Insert an M5 x 38 5 mm screw into each side of the frame Fully tighten the screws with the Allen wrench e Push the seat back down to fit the tabs on the edge of the seat back to the tabs on the seat bottom Seat Bottom Upper Slots Seat Back Recline Post
10. ou may need to reset the electronics Slide the power switch off and then back on e When motion from the swing becomes slow or stops replace the batteries e Protect the environment by not disposing of this product with household waste 2002 96 EC Check your local authority for meee recycling advice and facilities Europe only Battery Safety Information In exceptional circumstances batteries may leak fluids that can cause a chemical burn injury or ruin your product To avoid battery leakage e Do not mix old and new batteries or batteries of different types alkaline standard carbon zinc or rechargeable nickel cadmium e Insert batteries as indicated inside the battery compartment e Remove batteries during long periods of non use Always remove exhausted batteries from the product Dispose of batteries safely Do not dispose of this product in a fire The batteries inside may explode or leak e Never short circuit the battery terminals e Use only batteries of the same or equivalent type as recommended e Do not charge non rechargeable batteries e Remove rechargeable batteries from the product before charging e f removable rechargeable batteries are used they are only to be charged under adult supervision 10 Securing Your Child Anchored End Anchored End a a Waist Shoulder Belt Waist Shoulder mee ene Belt 3 TIGHTEN LOOSEN Crotch Belt 1 To tighten the waist belts e Feed the anchore
11. s e Position the seat bottom face down on a flat surface e With the seat back also face down fit the recline posts into the upper slots in the seat bottom Hinge Rod M4 5 x 12 mm Screw e Insert the hinge rod through the hinge on the seat bottom e Insert an M4 5 x 12 mm screw into the hinge rod Tighten the screw with a Phillips screwdriver Assembly gt e e ee M3 5 x 25 mm F Armrest M3 5 x 25 mm Screw ON e Insert an M3 5 x 25 mm washer head screw into the hole under each armrest Tighten the screws with a Phillips screwdriver Seat Tubes e While continuing to press the seat height adjustment levers slide a seat tube up through the socket in each seat hub Hint One of the seat tubes includes a tab Match this seat tube with the socket that has a notch Lever e Press the seat height adjustment levers on each side of the seat Assembly Frame Tube Hubs Latches 12 BACK VIEW 14 Crossbar e Fit the ends of the seat tubes up into the holes in each frame tube hub e First lift and then lower the latches onto the crossbar Hint You may need the help of another adult to hold the seat assembly in place 2 M5 x 32 mm Screws Elastic Loops 15 FRONT VIEW e Insert both elastic loops on the pad through the holes in the Note Do not attach the seat tubes to the frame crossbar in this assembly step e While holding the seat assembl
12. seat to the desired height e Push down on the seat to be sure it is secure Music and Sounds e Slide the power switch ON e Press the sound select buttons for music and other soothing sounds e Press the volume buttons to adjust the volume level Hint The swing will not work when in high chair mode e Slide the power switch to O to turn to sounds and music OFF 16 Convert to Swing WARNING Never convert to swing with child in product Release Button Latches IMPORTANT The seat must be completely lowered before using LAr the latches 1 _ ONT VIEW e Lift the latches on the back of the seat e While pushing the release button on the front of the tray pull the tray towards you and remove 4 y SIDE VIEW e Push the seat forward and release the latches 1 _ 4 _ 2 BACK VIEW e Press the lever on each seat height adjuster and completely lower the seat 17 Swing Use Swing Speed Buttons WARNING D To prevent injury or death from falls and being strangled in the Volume Buttons e fh af restraint system e Always use the restraint system Never use the tray to restrain child e Never use with an active child who may be able to climb out of the swing e Never leave child unattended e For best performance do not use the tray when using as a swing e Slide the power switch ON e Press the swing speed buttons to adjust the speed to the desired
13. the front of the seat pull the shoulder belts out and then fit them back through the desired shoulder belt slots in the seat pad and the seat back e Pull on the belts to be sure they are secure in the seat back Shoulder Belts 2 BACK VIEW e Unbuckle the restraint system e From the back of the seat push the shoulder belts through the Seat back slots 12 Convert to High Chair WARNING Never convert to high chair with child in product paz y 3 BACK VIEW gt e Fit the latches onto the crossbar and push into place Push down on the seat to be sure it is locked in place 1 BACK SIDE VIEW e From the back of the seat lift both latches i AD i 2 Ja wR A IMPORTANT Do not raise the seat height unless the seat is locked x pu to the crossbar NS 2 Crossbar e Press the levers on both seat height adjusters and lift or lower the seat to any of three different heights e Make sure both sides of the seat are adjusted to the same height e While lifting the latches pull the seat back toward the crossbar 13 e Push on the seat to be sure it is locked in place High Chair Use Hint Before use thoroughly wash all parts the trays that may contact food The tray is not dishwasher safe NN WARNING Prevent serious injury or death from falls or sliding out e The child should be secured in the high chair at all times by the restraint system either in the reclining or Armrests
14. y in place insert an M5 x 32 mm screw into the hole in each frame tube hub Tighten the screws with the Allen wrench Assembly Elastic Loops Waist Belts Tabs 16 BACK VIEW e From the back of the seat hook the elastic loops to the tabs on the seat back 7 18 e Insert the waist belts through the lowest slots in the seat pad Large Slot Crotch Belt Shoulder Belts 17 FRONT VIEW e From the front of the seat insert the crotch belt up through the large slot in the pad Make sure the crotch belt is not twisted e gt e Insert the shoulder belts through the slots in the pad Hint The shoulder belts are assembled to the seat back in the lower shoulder belt slots If you would like to change to the upper slots go to page 12 Changing Shoulder Belt Slots Assembly Pad Pocket Seat Back 20 SIDE VIEW e Fit the pocket at the top of the pad over the seat back Seat Bottom e Fit both clips on the bottom edge of the pad around the edge of the seat bottom Battery Installation 1 5V x 4 D LR20 e Locate the battery compartment door on the frame e Loosen the screws in the battery compartment door with a Phillips screwdriver e Insert four D LR20 alkaline batteries Hint We recommend using alkaline batteries for longer battery life e Replace the battery compartment door and tighten the screws Do not over tighten e f this product begins to operate erratically y
Download Pdf Manuals
Related Search
Related Contents
Guía del usuario para audífonos Quantum micro-BTE OnCell G2111/G2151I Series User`s Manual Philips Sunmobile HB 950 - Bolawi-Rent Calefacción - Troia España, SL solido 5 e-35 - Site interministériel sur l`assainissement non collectif quadcopter Documentation Release 0.0.1 Chris Laws Geovision GV-1251 smart card reader 今 、語り た い - mono shop MicroScanner Pro™ Copyright © All rights reserved.
Failed to retrieve file